Netgear RS200 User Manual

Download

User Manual

Nighthawk WiFi 7 Dual-Band Router

Model RS200 and Model RS150v1

NETGEAR, Inc.

350 E. Plumeria DriveSeptember 2024 San Jose, CA 95134, USA202-12737-01

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Support and Community

Visit netgear.com/support to get your questions answered and access the latest downloads.

You can also check out our NETGEAR Community for helpful advice at community.netgear.com.

Regulatory and Legal

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the device to your place of purchase within your return period.

Applicable to 6 GHz devices only: Only use the device indoors when the 6 GHz band is enabled. The operation of 6 GHz devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.

Trademarks

Trademarks© NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR trademarks are used for reference purposes only.

Revision History

CommentsPublish DatePublication Part

Number

First publication.September 2024202-12737-01

User Manual2

Chapter 1 Introduction

What is WiFi 7?.................................................................................. 11

Additional documentation............................................................... 11

Chapter 2 Hardware Setup

Unpack your router........................................................................... 13

Front panel LEDs and buttons......................................................... 13

Rear panel.......................................................................................... 16

Router label........................................................................................ 17

Position your router.......................................................................... 18

Cable your router.............................................................................. 19

Chapter 3 Connect to the Router Network and Access the Router

Connect to the router network........................................................ 22

Connect to the router WiFi network.......................................... 22

Connect to the router using a wired connection..................... 22

Types of logins.................................................................................. 23

Use a web browser to access the router........................................ 23

Automatic Internet setup............................................................. 23

Change the language.................................................................. 26

Install and manage your router with the Nighthawk app............ 26

Chapter 4 Specify Your Internet Settings

Use the Setup Wizard....................................................................... 29

Manually set up the Internet connection....................................... 30

Set an Internet connection without a login............................... 30

Set a PPPoE Internet connection................................................ 32

Set a PPTP or L2TP Internet connection.................................... 33

About high-speed Internet connections and Internet port

aggregation.................................................................................. 35

Get multi-gigabit Internet with Internet port aggregation...... 36

Set an IPv6 Internet connection...................................................... 37

Types of IPv6 Internet connections............................................ 37

Requirements for entering IPv6 addresses............................... 38

Use auto detect for an IPv6 Internet connection...................... 38

Set a 6to4 tunnel IPv6 Internet connection............................... 39

Set a pass-through IPv6 Internet connection............................ 41

Set a fixed IPv6 Internet connection.......................................... 42

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Set a DHCP IPv6 Internet connection........................................ 43

Set a PPPoE IPv6 Internet connection........................................ 45

Use auto config for an IPv6 Internet connection...................... 47

Set a 6rd IPv6 Internet connection............................................. 48

Manage the MTU size....................................................................... 50

MTU concepts............................................................................... 50

Change the MTU size................................................................... 51

Chapter 5 Control Access to the Internet

NETGEAR Armor............................................................................... 54

Activate Armor using the Nighthawk app...................................... 54

Network access control list.............................................................. 54

Enable the network access control list, set the access rule, and

allow or block connected devices.............................................. 55

Manage allowed devices currently not on the network.......... 57

Manage blocked devices currently not on the network.......... 59

Block Internet sites and services..................................................... 60

Use keywords to block Internet sites......................................... 60

Delete keywords from the blocked list...................................... 62

Prevent blocking on a trusted computer................................... 62

Block services from the Internet................................................. 63

Schedule when to block Internet sites and services................ 64

Set up security event email notifications........................................ 65

Chapter 6 Manage WiFi Settings

Change the name for a WiFi network............................................. 68

Change the WiFi password or the WiFi security option .............. 68

Set up WPA/WPA2 Enterprise WiFi security................................. 70

Hide or broadcast the SSID for a WiFi network............................. 71

Enable or disable AX WiFi............................................................... 72

Enable or disable OFDMA............................................................... 73

Enable or disable Smart Connect................................................... 74

Enable or disable 20/40 MHz coexistence for the 2.4 GHz radio. 74

Change the WiFi mode.................................................................... 75

Change the WiFi mode if AX WiFi is enabled.......................... 75

Change the WiFi mode if AX WiFi is disabled.......................... 77

Change the 2.4 GHz or 5 GHz WiFi channel.................................. 78

Change your country or region....................................................... 79

Set up a guest WiFi network............................................................ 79

Manage advanced WiFi settings..................................................... 81

Enable or disable a WiFi radio.................................................... 81

Set up a WiFi schedule................................................................ 82

Enable or disable implicit beamforming................................... 83

Enable or disable MU-MIMO...................................................... 84

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Enable or disable PMF................................................................. 84

Enable or disable airtime fairness.............................................. 85

Change the CTS/RTS threshold or preamble mode for a

radio............................................................................................... 86

Use the WPS Wizard for WiFi connections.................................... 87

Use the WPS Wizard with the push button............................... 87

Use the WPS Wizard with a PIN.................................................. 88

Chapter 7 Manage the WAN and LAN Network Settings

Manage the WAN settings............................................................... 90

Change the WAN security settings............................................ 90

Set up a default DMZ server........................................................ 91

Manage IGMP proxying............................................................... 92

Manage NAT filtering................................................................... 92

Manage the SIP application-level gateway............................... 93

Change the LAN IP address settings or RIP settings.................... 94

Set the IP addresses that the router assigns.................................. 95

Disable the DHCP server feature in the router.............................. 96

Manage reserved LAN IP addresses............................................... 97

Reserve an IP address.................................................................. 97

Edit a reserved IP address........................................................... 98

Delete a reserved IP address entry............................................ 99

Manage custom static routes........................................................... 99

Set up a static route................................................................... 100

Edit a static route........................................................................ 101

Delete a static route................................................................... 102

Set up an IPTV port or a bridge for a port group or VLAN tag

group................................................................................................ 102

Set up a bridge for a port group.............................................. 103

Set up a bridge for a VLAN tag group..................................... 104

Manage Ethernet LAN port aggregation to a LAN device........ 105

Set up LAN port aggregation to a LAN device...................... 106

View or change the router LAN port aggregation mode..... 107

Chapter 8 Optimize Performance

Enable QoS...................................................................................... 110

Set the Internet bandwidth for your router................................. 110

Update the QoS database............................................................. 111

Manage Wi-Fi Multimedia QoS..................................................... 112

Improve network connections with Universal Plug and Play..... 113

Chapter 9 Manage and Monitor Your Router

Update the router firmware........................................................... 116

Check for new firmware and update the router..................... 116

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Manually upload firmware to the router ................................. 117

Manage the firmware update settings.................................... 118

Change the admin password........................................................ 118

Enable admin password reset....................................................... 119

Reset the admin password............................................................ 120

Use HTTPS to access the router.................................................... 121

Change the router’s device name................................................ 121

Manage the router configuration file........................................... 122

Back up the settings................................................................... 122

Restore the settings................................................................... 123

Erase the settings....................................................................... 123

Monitor the router and network................................................... 124

View information about the router and the Internet and WiFi

settings........................................................................................ 124

View devices currently on the network.................................... 125

View and manage logs of router activity................................. 126

View the Internet connection status or renew the connection. 127

View the PPPoE Internet connection status or renew the

connection.................................................................................. 129

View the packet statistics of the Internet and LAN ports and WiFi

networks ..................................................................................... 129

Monitor, meter, and control Internet traffic................................. 130

Start the traffic meter without traffic volume restrictions...... 131

Restrict Internet traffic by volume............................................ 131

Restrict Internet traffic by connection time............................. 133

View the Internet traffic volume and statistics........................ 134

Unblock the traffic meter after the traffic limit is reached..... 134

Set the NTP server.......................................................................... 135

Set your time zone and daylight saving time.............................. 136

Set up the router as a WiFi access point...................................... 137

Return the router to router mode................................................. 138

Manage LED blinking or turn off LEDs......................................... 138

Connect to your router with Anywhere Access........................... 139

Return the router to its factory default settings........................... 140

Use the Reset button................................................................. 140

Erase the settings....................................................................... 141

Chapter 10 Share a USB Storage Device Attached to the Router

USB device requirements.............................................................. 143

Connect a USB storage device to the router............................... 143

Display network folders on a storage device.............................. 144

Access a storage device connected to the router...................... 145

Access a storage device connected to the router from a

Windows-based computer....................................................... 145

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Map a USB device to a Windows network drive.................... 145

Access a storage device connected to the router from a Mac. 146

Manage access to a USB storage device..................................... 147

Enable FTP access within your network....................................... 149

Change a network folder on a USB storage device................... 150

Add a network folder on a USB storage device.......................... 151

Safely remove a USB storage device............................................ 152

Change the media server settings or rescan media files........... 152

Chapter 11 Use Dynamic DNS to Access a USB Storage Device From the Internet

Set up and manage Dynamic DNS............................................... 155

Set up a new Dynamic DNS account....................................... 155

Use a Dynamic DNS account that you already have.............. 156

Manage your existing NETGEAR or No-IP Dynamic DNS

account........................................................................................ 157

Your personal FTP server............................................................... 158

Set up your personal FTP server: Overview of steps............. 158

Set up FTP access through the Internet.................................. 158

Set up HTTPS access through the Internet.................................. 159

Access a USB storage device through the Internet.................... 160

Chapter 12 Use OpenVPN to Access Your Network

About VPN connections................................................................. 163

LAN IP addressing in VPN networks............................................. 163

Enable OpenVPN service on the router....................................... 164

Install OpenVPN software on a VPN client.................................. 165

Install OpenVPN software on a Windows-based computer.. 166

Install OpenVPN software on a Mac........................................ 167

Install OpenVPN software on an iOS device........................... 168

Install OpenVPN software on an Android device.................. 169

Use VPN to access your Internet service at home...................... 170

Allow VPN client Internet access in the router....................... 170

Block VPN client Internet access in the router........................ 171

Chapter 13 Manage Port Forwarding and Port Triggering

Manage port forwarding to a local server................................... 174

Forward incoming traffic to a local server............................... 174

Add a custom port forwarding service or application........... 175

Change a port forwarding rule................................................. 176

Remove a port forwarding rule................................................ 177

Application example: Make a local web server public.......... 177

How the router implements the port forwarding rule........... 178

Manage port triggering................................................................. 178

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Add a port triggering rule......................................................... 179

Change a port triggering rule.................................................. 180

Remove a port triggering rule.................................................. 181

Set the time-out period for port triggering............................ 182

Disable an individual port triggering rule............................... 182

Disable port triggering.............................................................. 183

Application example: Port triggering for Internet Relay Chat. 184

Chapter 14 Troubleshooting

Quick tips......................................................................................... 186

Sequence to restart your network............................................ 186

Check the power adapter and Ethernet cable connections.. 186

Check the WiFi settings............................................................. 186

Check the network settings...................................................... 187

Reboot the router from its router web interface......................... 187

Troubleshoot with the LEDs.......................................................... 188

Standard LED behavior when the router is powered on...... 188

Power LED is off ......................................................................... 188

Power LED stays solid amber or blinking amber................... 188

Internet or Ethernet LAN port LEDs are off............................. 189

WiFi LED is off............................................................................. 189

You cannot log in to the router..................................................... 189

You cannot access the Internet..................................................... 191

Troubleshoot Internet browsing................................................... 193

Changes are not saved.................................................................. 193

Troubleshoot WiFi connectivity.................................................... 193

Troubleshoot your network using the ping utility...................... 194

Test the LAN path to your router............................................. 194

Test the path from a Windows-based computer to a remote

device.......................................................................................... 195

Introduction

This user manual is for the NETGEAR Nighthawk®WiFi 7 Dual-Band Router Model RS200 and Model RS150v1.

Model RS200 supports WiFi 7 (IEEE 802.11be) with a combined WiFi speed of up to

6.45 Gbps and dual-band concurrent radio operation:

2.4 GHz radio: Supports IEEE 802.11 n/ac/ax/be with 4096-QAM, 20/40 MHzchannel

• width, and a speed of up to 0.7 Gbps

5 GHz radio: Support IEEE 802.11 n/ac/ax/be with 4096-QAM, 20/40/80/160 MHz

• channel width, and a speed of up to 5.8 Gbps

Model RS150v1 supports WiFi 7 (IEEE 802.11be) with a combined WiFi speed of up to

5.0 Gbps and dual-band concurrent radio operation:

2.4 GHz radio: Supports IEEE 802.11 n/ac/ax/be with 4096-QAM, 20/40 MHz channel

• width, and a speed of up to 0.7 Gbps

5 GHz radio: Support IEEE 802.11 n/ac/ax/be with 4096-QAM, 20/40/80/160 MHz

• channel width, and a speed of up to 4.3 Gbps

Both routers provide one 2.5GbE Internet port for cable and fiber ISP connections up to 2.5 Gbps, one 2.5GbE LAN port for connection to high-speed LAN devices, and three 1 Gigabit LAN ports.

This chapter contains the following sections:

• What is WiFi 7?

• Additional documentation

NOTE: For more information about the topics that are covered in this manual, visit the support website at netgear.com/support/.

NOTE: Firmware updates with new features and bug fixes are made available from time to time at netgear.com/support/download/. You can check for and download new firmware manually. If the features or behavior of your product does not match what is described in this manual, you might need to update the firmware.

NOTE: In this manual, WiFi network means the same thing as SSID (service set identifier or WiFi network name) or VAP (virtual access point). That is, when we refer to a WiFi network we mean an individual SSID or VAP.

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

What is WiFi 7?

WiFi 7, also known as IEEE 802.11be Extremely High Throughput (EHT), is a next-generation WiFi standard. The new standard provides the capability for multi-gigabit (multi-gig) WiFi throughout the home with faster speeds, less interference, and better performance for high-bandwidth online activities.

New technologies in WiFi 7 provide the following benefits:

2.4 times faster speed than WiFi 6

•

Double the maximum bandwidth for your devices

•

Lower latency than WiFi6

•

A more reliable connection

•

For more information, visit the NETGEAR WiFi 7 page at netgear.com/home/discover/wifi7.

Additional documentation

The following documents are available at netgear.com/support/download/:

Quick start guide

•

Data sheet

•

For information about the NETGEAR Nighthawk app, visit netgear.com/home/services/nighthawk-app/.

User Manual11Introduction

Hardware Setup

This chapter contains the following sections:

• Unpack your router

• Front panel LEDs and buttons

• Rear panel

• Router label

• Position your router

• Cable your router

For more information about the topics covered in this manual, visit the support website at netgear.com/support.

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Unpack your router

Your package contains the router, an Ethernet cable, and the power adapter (the type varies by region).

Figure 1. Package contents

Front panel LEDs and buttons

The status LEDs and two buttons are located on the front panel of the router.

User Manual13Hardware Setup

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Figure 2. Top view

Table 1. LED descriptions

Power LED1.

2. Internet LED

DescriptionLED and Button

Solid white: The router is ready.

Solid amber and then blinking amber: The Reset button was pressed. When

you first press the Reset button, the LED lights solid amber. After 5 seconds, the LED turns blinking amber, and the router resets to factory defaults.

Off: Power is not supplied to the router.

Solid white: The Internet connection is ready.

Solid amber: A cable was plugged into the port, but the Internet connection is

not yet ready.

Blinking: The port is sending or receiving traffic.

Off: No Ethernet cable is connected between the router and the modem.

User Manual14Hardware Setup

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Table 1. LED descriptions (Continued)

DescriptionLED and Button

Ethernet LAN ports 1–4

3. LEDs

USB 3.0 port LED4.

2.4 GHz WiFi LED5.

5 GHz WiFi LED6.

The LED color indicates the speed of the Ethernet connection at each LAN port: white for the maximum supported speed on each port (2.5 Gbps on port 1, 1 Gbps on ports 2-4) and amber for lower speeds.

Solid white: The router detected a 2.5 Gbps (port 1) or 1 Gbps (ports 2-4) link with a powered-on device.

Blinking white: The port is sending or receiving traffic at 2.5 Gbps (port 1) or 1 Gbps (ports 2-4).

Solid amber: The router detected a lower speed link with a powered-on device.

Blinking amber: The port is sending or receiving traffic at a lower speed.

Off: No device is connected to this Ethernet LAN port.

Solid white: A USB device is connected to the USB 3.0. port.

Blinking white: The USB 3.0 port is sending or receiving traffic.

Off: No USB device is connected to the USB 3.0 port.

Solid white: The 2.4 GHz WiFi radio is operating.

Off: The 2.4 GHz WiFi radio is off.

Solid white: The 5 GHz WiFi radio is operating.

Off: The 5 GHz WiFi radio is off.

Sync/WPS LED7.

Pressing the Sync/WPS button lets your WPS-enabled device join your router’s WiFi network without typing the WiFi password.

Solid white: The Sync/WPS LED is always solid white. This is normal behavior.

Blinking white: The WPS process is active so that you can connect a WPS-enabled

device to your router’s WiFi network. When the device is connected, the sync/WPS LED shows solid white again.

The Sync/WPS LED is also blinking white when the router is in factory default state or you reset the router to factory default settings.

Off: The router or its LEDs are turned off.

Pressing the LED On/Off button turns off all LEDs except for the Power LED.LED On/Off button8.

User Manual15Hardware Setup

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Rear panel

The following figure shows the rear panel connectors and buttons.

Figure 3. Rear panel

The rear panel contains the following components:

A. Reset button: Pressing the Reset button resets the router.

•

If the Reset button is pressed for at least five seconds and the Power LED blinks amber, the router returns to its factory settings.

B. Power On/Off button: Press the Power On/Off button to provide power to the

• router.

User Manual16Hardware Setup

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

C. 2.5G LAN port: One RJ-45 LAN port that supports speeds up to 2.5 Gbps. Use

• a Category 5e (Cat5e) Ethernet cable or higher rated Ethernet cable to connect the

router to a high-speed LAN server, LAN storage device, or another LAN device. The router supports port aggregation:

LAN aggregation: Use Ethernet LAN ports 1 and 2 to set up a port aggregation

○

link to a LAN device that also supports Ethernet LAN port aggregation. For more information, see Manage Ethernet LAN port aggregation to a LAN device on page 105.

D. Gigabit Ethernet LAN ports: Three Gigabit Ethernet RJ-45 LAN ports that support

• 1G, 100M, and 10M speed. Use these ports to connect Ethernet LAN devices to your

router. The router supports port aggregation:

Internet (WAN) aggregation: Use Ethernet LAN port 4 with the 2.5G Internet

○

port to set up a multi-gigabit Internet connection with port aggregation. For more information, see Get multi-gigabit Internet with Internet port aggregation on page 36.

NOTE: You can set up both LAN aggregation and Internet (WAN) aggregation.

E. USB 3.0 port: Use the USB 3.0 port to connect a USB storage device to your

• router.

F. 2.5G Internet port: An RJ-45 Internet port (marked with yellow) that supports

• speeds up to 2.5 Gbps. Use a Category 5e (Cat5e) Ethernet cable or higher rated

Ethernet cable to connect a high-speed modem for a high-speed Internet connection. For more information, see About high-speed Internet connections and Internet port aggregation on page 35.

G. DC power connector: Connect the power adapter that came in your product

• package to the DC power connector.

Router label

The router label shows the login information, WiFi Network Name (SSID), network key (password), serial number, and MAC address.

User Manual17Hardware Setup

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Figure 4. Router label

Position your router

The router lets you access your network anywhere within the operating range of your WiFi network. However, the operating distance or range of your WiFi connection can vary significantly depending on the physical placement of your router. In addition, position your router according to the following guidelines:

Place your router near the center of the area where your computers and other devices

• operate, and within line of sight to your WiFi devices.

Make sure that the router is within reach of an AC power outlet and near Ethernet

• cables for wired devices.

Place the router in an elevated location, minimizing the of number walls and ceilings

• between the router and your other devices.

User Manual18Hardware Setup

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To avoid wireless signal interference, place the router away from electrical devices

• such as these:

Ceiling fans

○

Home security systems

○

Microwaves

○

Computers

○

The base of a cordless phone

○

2.4 GHz or 5 GHz cordless phones

○

Place the router away from large metal surfaces, large glass surfaces, insulated walls,

• and items such as these:

Solid metal doors

○

Aluminum studs

○

Fish tanks

○

Mirrors

○

Brick

○

Concrete

○

The following factors might limit the range of your WiFi:

The thickness and number of walls the WiFi signal passes through can limit the range.

•

Other WiFi access points in and around your home might affect your router’s signal.

• WiFi access points are routers, repeaters, WiFi range extenders, and any other

devices that emit a WiFi signal for network access.

Cable your router

Connect your router to a modem and power on your router.

User Manual19Hardware Setup

Internet

10G

Ethernet

ResetPower

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Figure 5. Cable your router

To cable your router:

1. Unplug your modem, remove and reinsert the backup battery if it uses one, and then plug the modem back in.

2. Use the Ethernet cable to connect the modem to the yellow Internet port on the router.

NOTE: If your Internet connection does not require a modem, connect the Ethernet cable going to your home to the yellow Internet port on the router.

3. Connect the power adapter to your router and plug the power adapter into an outlet.

The router’s Power LED lights solid white when the router is ready.

After you connect your router to a modem and power it on, finish your router’s installation process using the Nighthawk app or router web interface. For more information, see Connect to the Router Network and Access the Router on page 21.

User Manual20Hardware Setup

Connect to the Router Network and Access the Router

You can connect to the router’s WiFi networks or use a wired Ethernet connection. This chapter explains the ways you can connect and how to access the router and log in.

The chapter contains the following sections:

• Connect to the router network

• Types of logins

• Use a web browser to access the router

• Install and manage your router with the Nighthawk app

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Connect to the router network

You can connect to the router network using a wired or WiFi connection.

NOTE: If you set up your computer to use a static IP address, change the settings so that it uses Dynamic Host Configuration Protocol (DHCP).

Connect to the router WiFi network

You can connect a WiFi-enabled computer or mobile device to the router WiFi network using the router WiFi network name (SSID) and WiFi password (network key)

To connect to the WiFi network:

1. Make sure that the router is receiving power (its Power LED is lit).

2. On your computer or mobile device, open your WiFi network management application.

This is the application that lets you manage your WiFi connections.

3. Find and select the router WiFi network name (SSID).

The router’s default WiFi network name (SSID) is on the router label.

4. Enter the router WiFi password.

The router’s default WiFi password is on the router label. The WiFi password is also known as the network key or passphrase.

Your computer or mobile device connects to the WiFi network.

Connect to the router using a wired connection

You can connect your computer to the router using an Ethernet cable and join the router’s local area network (LAN). After setup, you can also connect other wired devices.

To connect your computer or other device to the router with an Ethernet cable:

1. Make sure that the router is receiving power (its Power LED is lit).

2. Connect an Ethernet cable to an Ethernet port on your computer.

If your computer doesn’t have an Ethernet port, you might be able to connect a USB to Ethernet adapter to a USB port on your computer, and then connect the Ethernet cable to the adapter’s port.

3. Connect the other end of the Ethernet cable to an Ethernet LAN port on the router.

User Manual22Connect to the Router Network

and Access the Router

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Your computer connects to the local area network (LAN).

Types of logins

Separate types of logins serve different purposes. It is important that you understand the differences so that you know which login to use when.

Several types of logins are associated with the router:

ISP login: The login that your Internet service provider (ISP) gave you logs you in to

• your Internet service. Your ISP gave you this login information in a letter or some

other way. If you cannot find this login information, contact your ISP.

WiFi password: Your router is preset with a unique WiFi network name (SSID) and

• password for WiFi access. This information is on the router label. The WiFi password

is also known as the network key or passphrase.

NETGEAR account login: The free NETGEAR account that you need to register your

• router, manage your router remotely, and manage your subscriptions. If you do not

have a NETGEAR account, you can create one.

Router login: The router login password that you need to log in to the router with

• the admin user name when you use a web browser to access and configure the

router.

Use a web browser to access the router

When you connect to the network (either with WiFi or with an Ethernet cable), you can use a web browser to access the router to view or change its settings. We call the router user interface the router web interface.

When you access the router web interface, the software automatically checks to see if your router can connect to your Internet service.

Automatic Internet setup

You can set up your router automatically (see the information below) or manually (see Manually set up the Internet connection on page 30). In either case, you must use a web browser to access the router.

User Manual23Connect to the Router Network

and Access the Router

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Before you start the setup process, get your ISP information and make sure that the computers and devices in the network are using the settings described here. When your Internet service starts, your Internet service provider (ISP) typically gives you all the information needed to connect to the Internet. For example, for DSL service, you might need the following information to set up your router:

The ISP configuration information for your DSL account

•

ISP login name and password

•

Fixed or static IP address setting (special deployment by ISP; this setting is rare)

•

If you cannot locate this information, ask your ISP to provide it.

NOTE: If your Internet service is going through your TV or fiber cable, you might not need the login information.

When your Internet connection is working, you no longer need to launch the ISP login program on your computer to access the Internet. When you start an Internet application, your router automatically logs you in.

The NETGEAR installation assistant runs on any device with a web browser. Installation and basic setup takes about 15 minutes to complete.

To automatically set up your router:

1. Make sure that the router is powered on.

2. Make sure that your computer or mobile device is connected to the router with an Ethernet cable (wired) or over WiFi with the preset security settings listed on the label.

NOTE: If you want to change the router’s WiFi settings, use a wired connection to avoid being disconnected when the new WiFi settings take effect.

3. Launch a web browser.

The page that displays depends on whether you accessed the router before:

The first time you set up the Internet connection for your router, the browser goes

•

to http://www.routerlogin.net and the Configuring the Internet Connection page displays.

If you already set up the Internet connection, enter http://www.routerlogin.net

•

in the address field for your browser to start the installation process.

The page that displays recommends that you use the Nighthawk app. However, the current procedure describes how you can use the router web interface.

4. If the installation process does not start and the browser does not display the page that recommends that you use the Nighthawk app, do the following:

User Manual24Connect to the Router Network

and Access the Router

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Make sure that the computer is connected to one of the Ethernet LAN ports on

•

the router or over WiFi to the router.

Make sure that the router is receiving power and that its Power LED is lit.

•

Close and reopen the browser or clear the browser cache.

•

Browse to http://www.routerlogin.net.

•

If the computer is set to a static or fixed IP address (this setting is uncommon),

•

change it to obtain an IP address automatically from the router.

Use the Reset button, to reset the router to factory default settings (see Use the

•

Reset button on page 140).

5. Scroll down and click the If you don’t have a compatible smartphone, click here link.

A welcome page displays.

6. Follow the onscreen instructions.

The router detects your Internet settings.

7. Follow the onscreen instructions to complete the installation process.

If the router does not detect the Internet settings, the installation assistant cannot complete the installation process, and you must start the installation process again:

1. Before you start again, review your settings. Make sure that you select the correct options and type everything correctly.

2. If the router still does not detect the Internet settings, contact your ISP to verify that you are using the correct configuration information.

3. If problems persist, register your router and contact NETGEAR Technical Support.

Log in to the router after you set up the router

When you set up your router while the router is in factory default state, the browser automatically starts the NETGEAR installation assistant.

After you set up the router, if you want to view or change settings for the router, you can use a browser to log in to the router web interface.

To log in to the router web interface:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

User Manual25Connect to the Router Network

and Access the Router

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

NOTE: You can also enter http://www.routerlogin.com or http://192.168.1.1. The procedures in this manual use http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

Change the language

By default, the Auto setting uses your region to automatically set the language that displays when you log in to the router web interface.

To change the language:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. In the upper right corner, select a language from the menu.

5. When prompted, click the OK button to confirm this change.

The page refreshes with the language that you selected.

Install and manage your router with the Nighthawk app

With the Nighthawk app, you can easily install and manage your router. The app lets you update the router to the latest firmware, allows you to personalize your WiFi network, and helps you to register your router with NETGEAR. You can also manage your router remotely and use the Armor and Smart Parental Controls services.

User Manual26Connect to the Router Network

and Access the Router

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The Nighthawk app is available for iOS and Android mobile devices.

NOTE: Your router is not connected to the Internet until you finish setting it up with the app. If you are connected to your router’s WiFi network before your router is set up, you do not have Internet access and cannot download the app.

Use your cellular data or connect to your previous router’s WiFi network to download the app. During router installation, the app instructs you when you need to connect to your router's WiFi.

To install your router using the Nighthawk app:

1. Visit Nighthawk-app.com to download the Nighthawk app.

NOTE: To download the app, you need to use your cellular data or connect your mobile device to your previous router’s WiFi network.

2. Wait for the Nighthawk app to download on your mobile device.

3. Launch the Nighthawk app.

4. Follow the instructions that display in the app to install your router and connect to the Internet.

and Access the Router

User Manual27Connect to the Router Network

Specify Your Internet Settings

Usually, the quickest way to set up the router to use your Internet connection is to allow the NETGEAR installation assistant to detect the Internet connection.

After you set up your router, you can use the Setup Wizard to redetect the Internet settings, or you can manually specify your Internet settings.

This chapter contains the following sections:

• Use the Setup Wizard

• Manually set up the Internet connection

• Set an IPv6 Internet connection

• Manage the MTU size

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Use the Setup Wizard

You can use the Setup Wizard to redetect your Internet settings and automatically set up your router.

To use the Setup Wizard:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup Wizard.

The Setup Wizard page displays.

5. Select the Yes radio button.

6. Click the Next button.

The Setup Wizard searches your Internet connection for servers and protocols to determine your Internet configuration.

7. Follow the onscreen instructions.

The router detects your Internet settings.

8. Follow the onscreen instructions to complete the Setup Wizard process.

If the router does not detect the Internet settings, the Setup Wizard cannot complete its process, and you must start the Setup Wizard again:

1. Before you start again, review your settings. Make sure that you select the correct options and type everything correctly.

2. If the router still does not detect the Internet settings, contact your ISP to verify that you are using the correct configuration information.

3. If problems persist, register your router and contact NETGEAR Technical Support.

User Manual29Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Manually set up the Internet connection

You can view or change the router’s Internet connection settings.

Set an Internet connection without a login

You can manually specify the connection settings for an Internet service for which you do not need to log in. Use the information that your ISP gave you to connect to your Internet service. If you cannot find this information, contact your ISP. Entering incorrect information might prevent the router from connecting to the Internet.

To set an Internet connection without a login:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Internet.

The Internet Setup page displays.

5. In the WAN Preference section, select one of the following options:

Internet Port (2.5 Gbps). Select this option if you connected a modem to the

•

Internet port on your router. For more information about a high-speed Internet connection, see About high-speed Internet connections and Internet port aggregation on page 35.

Multi-Gig Internet (2.5 Gbps + 1 Gbps). Select this option if you want to set up

•

multi-gigabit Internet and use the Internet port together with Ethernet LAN port 4 for your Internet connection. For more information, see Get multi-gigabit Internet with Internet port aggregation on page 36.

6. In the Does your Internet connection require a login? section, leave the No radio button selected.

7. If your Internet connection requires an account name or host name, do the following:

User Manual30Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

a. In the Account Name section, click the Edit button.

b. Enter the account name.

By default, the account name is the model number of the router.

c. Click the Apply button.

d. Select Internet.

The Internet Setup page displays again.

8. If your Internet connection requires a domain name, type it in the Domain Name (If Required) field.

For the other sections on this page, the default settings usually work, but you can change them.

9. Select an Internet IP Address radio button:

Get Dynamically from ISP: Your ISP uses DHCP to assign your IP address. Your

•

ISP automatically assigns these addresses.

Use Static IP Address: Enter the IP address, IP subnet mask, and the gateway IP

•

address that your ISP assigned. The gateway is the ISP router to which your router connects.

10. Select a Domain Name Server (DNS) Address radio button:

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

11. Select a Router MAC Address radio button:

Use Default Address: Use the default MAC address.

•

Use Computer MAC Address: The router captures and uses the MAC address

•

of the computer that you are now using. You must use the one computer that the ISP allows.

Use This MAC Address: Enter the MAC address that you want to use.

•

12. Click the Apply button.

Your settings are saved.

13. Click the Test button to test your Internet connection.

If the NETGEAR website does not display within one minute, see You cannot access the Internet on page 191.

User Manual31Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Set a PPPoE Internet connection

You can manually set the connection settings for a PPPoE Internet service for which you must log in. Use the information that your ISP gave you to connect to your Internet service. If you cannot find this information, contact your ISP. Entering incorrect information might prevent the router from connecting to the Internet.

To set a PPPoE Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Internet.

The Internet Setup page displays.

5. In the WAN Preference section, select one of the following options:

Internet Port (2.5 Gbps). Select this option if you connected a modem to the

•

Internet port on your router. For more information about a high-speed Internet connection, see About high-speed Internet connections and Internet port aggregation on page 35.

Multi-Gig Internet (2.5 Gbps + 1 Gbps). Select this option if you want to set up

•

6. In the Does your Internet connection require a login? section, select the Yes radio button.

The page adjusts.

7. From the Internet Service Provider menu, select PPPoE as the encapsulation method.

This is the default selection in the menu.

8. In the Login field, enter the login name that your ISP gave you.

This login name is often an email address.

9. In the Password field, type the password that you use to log in to your Internet service.

10. If your ISP requires a service name, type it in the Service Name (if Required) field.

User Manual32Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

11. From the Connection Mode menu, select Always On, Dial on Demand, or Manually Connect.

12. To change the number of minutes until the Internet login times out, in the Idle Timeout (In minutes) field, type the number of minutes.

This is how long the router keeps the Internet connection active when no one on the network is using the Internet connection. A value of 0 (zero) means never log out.

13. Select an Internet IP Address radio button:

Get Dynamically from ISP: Your ISP uses DHCP to assign your IP address. Your

•

ISP automatically assigns these addresses.

Use Static IP Address: Enter the IP address, IP subnet mask, and the gateway IP

•

address that your ISP assigned. The gateway is the ISP router to which your router connects.

14. Select a Domain Name Server (DNS) Address radio button:

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

15. Select a Router MAC Address radio button:

Use Default Address: Use the default MAC address.

•

Use Computer MAC Address: The router captures and uses the MAC address

•

of the computer that you are now using. You must use the one computer that the ISP allows.

Use This MAC Address: Enter the MAC address that you want to use.

•

16. Click the Apply button.

Your settings are saved.

17. Click the Test button to test your Internet connection.

If the NETGEAR website does not display within one minute, see You cannot access the Internet on page 191.

Set a PPTP or L2TP Internet connection

You can manually specify the connection settings for a PPTP or L2TP Internet service for which you must log in. Use the information that your ISP gave you to connect to your Internet service. If you cannot find this information, contact your ISP. Entering incorrect information might prevent the router from connecting to the Internet.

User Manual33Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To set a PPTP or L2TP Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Internet.

The Internet Setup page displays.

5. In the WAN Preference section, select one of the following options:

Internet Port (2.5 Gbps). Select this option if you connected a modem to the

•

Internet port on your router. For more information about a high-speed Internet connection, see About high-speed Internet connections and Internet port aggregation on page 35.

Multi-Gig Internet (2.5 Gbps + 1 Gbps). Select this option if you want to set up

•

6. Select the Does your Internet connection require a login? Yes radio button.

The page adjusts.

7. From the Internet Service Provider menu, select PPTP or L2TP as the encapsulation method.

The page adjusts again.

8. In the Login field, enter the login name that your ISP gave you.

This login name is often an email address.

9. In the Password field, type the password that you use to log in to your Internet service.

10. From the Connection Mode menu, select Always On, Dial on Demand, or Manually Connect.

11. To change the number of minutes until the Internet login times out, in the Idle Timeout (In minutes) field, type the number of minutes.

This is how long the router keeps the Internet connection active when no one on the network is using the Internet connection. A value of 0 (zero) means never log out.

User Manual34Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

12. If your ISP gave you fixed IP addresses and a connection ID or name, type them in the My IP Address, Subnet Mask, Server Address, Gateway IP Address, and Connection ID/Name fields.

If your ISP did not give you IP addresses, a connection ID, or name, leave these fields blank. The connection ID or name applies to a PPTP service only.

13. Select a Domain Name Server (DNS) Address radio button:

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

14. Select a Router MAC Address radio button:

Use Default Address: Use the default MAC address.

•

Use Computer MAC Address: The router captures and uses the MAC address

•

of the computer that you are now using. You must use the one computer that the ISP allows.

Use This MAC Address: Enter the MAC address that you want to use.

•

15. Click the Apply button.

Your settings are saved.

16. Click the Test button to test your Internet connection.

If the NETGEAR website does not display within one minute, see You cannot access the Internet on page 191.

About high-speed Internet connections and Internet port aggregation

Use the router’s yellow Internet port, which supports speeds up to 2.5 Gbps, to connect the router to your modem.

The router’s Internet speed depends on the speed that your ISP offers and the speed that your modem supports. For example, if your ISP and your modem both support a speed of 2.5 Gbps, the router’s Internet speed is also 2.5 Gbps. However, if, for example, your ISP supports a speed of 2.5 Gbps but your modem supports a speed of only 1 Gbps, your router’s Internet speed is limited to 1 Gbps.

If your ISP offers Internet speeds faster than 2.5 Gbps, your modem does not provide a high-speed or multi-gigabit port, but your modem does support link aggregation, set up Internet port aggregation by aggregating the yellow Internet port and Ethernet LAN

User Manual35Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

port 4 on the router. By default, the Ethernet LAN 4 port functions as a regular LAN port, but you change the function of the Ethernet LAN port 4 to a second WAN port in an Internet link aggregation setup. For more information, see Get multi-gigabit Internet with Internet port aggregation on page 36.

Get multi-gigabit Internet with Internet port aggregation

If your ISP offers Internet speeds faster than 1 Gbps, your modem does not provide a high-speed or multi-gigabit port, but your modem does support link aggregation, you can get multi-gigabit Internet with your router by setting up Internet port aggregation. You can aggregate the Internet port and Ethernet LAN port 4 on the router.

NOTE: For information about a different type of aggregation, which is port aggregation to a LAN device, see Manage Ethernet LAN port aggregation to a LAN device on page 105.

To set up Internet port aggregation, you need the following:

A service provider that offers an Internet speed that’s over 1 Gbps.

•

A modem that support both an Internet speed that’s over 1 Gbps and two Ethernet

• ports that support static Link Aggregation Control Protocol (LACP), for example, the

NETGEAR Nighthawk Multi-Gig Cable Modem, model CM1200.

To set up Internet port aggregation:

1. Set up Internet port aggregation on your modem.

For information about how to set up Internet port aggregation on your modem, see the documentation that came with your modem.

2. Launch a web browser from a computer or mobile device that is connected to the router network.

3. Enter http://www.routerlogin.net.

A login window displays.

4. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

5. Select Internet.

The Internet Setup page displays.

6. In the WAN Preference section, select the Multi-Gig Internet (2.5 Gbps + 1 Gbps) radio button.

User Manual36Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

7. Click the Apply button.

Your settings are saved.

8. Connect the yellow Internet port and the Ethernet LAN port 4 on your router to two Ethernet ports on your modem.

Set an IPv6 Internet connection

The router supports many different types of IPv6 Internet connections for which you can specify the settings manually.

Types of IPv6 Internet connections

The router can support an IPv6 Internet connection through the following connection types:

Auto Detect: See Use auto detect for an IPv6 Internet connection on page 38.

•

6to4 tunnel: See Set a 6to4 tunnel IPv6 Internet connection on page 39.

•

Pass-through: See Set a pass-through IPv6 Internet connection on page 41.

•

Fixed: See Set a fixed IPv6 Internet connection on page 42.

•

DHCP: See Set a DHCP IPv6 Internet connection on page 43.

•

PPPoE: See Set a PPPoE IPv6 Internet connection on page 45.

•

Auto Config: See Use auto config for an IPv6 Internet connection on page 47.

•

6rd: See Set a 6rd IPv6 Internet connection on page 48.

•

Which connection type you must use depends on your IPv6 ISP. Follow the directions that your IPv6 ISP gave you.

If you are not sure what type of IPv6 connection the router uses, use the Auto Detect

• connection type, which lets the router detect the IPv6 type that is in use (see Use

auto detect for an IPv6 Internet connection on page 38).

If your ISP did not provide details, use the 6to4 tunnel connection type (see Set a

• 6to4 tunnel IPv6 Internet connection on page 39).

When you enable IPv6 and select any connection type other than IPv6 pass-through, the router starts the stateful packet inspection (SPI) firewall function on the WAN interface. The router creates connection records and checks every inbound IPv6 packet. If the router does not expect to receive such a packet, or the packet is not in the connection record, the router blocks this packet.

User Manual37Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Requirements for entering IPv6 addresses

IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated by colons. You can reduce any four-digit group of zeros within an IPv6 address to a single zero or omit it.

All of the following examples specify the same IPv6 address:

2001:db8:0000:0000:020f:24ff:febf:dbcb

•

2001:db8:0:0:20f:24ff:febf:dbcb

•

2001:db8::20f:24ff:febf:dbcb

•

2001:db8:0:0:20f:24ff:128.141.49.32

•

The following errors invalidate an IPv6 address:

More than eight groups of hexadecimal quartets

•

More than four hexadecimal characters in a quartet

•

More than two colons in a row

•

Use auto detect for an IPv6 Internet connection

To set up an IPv6 Internet connection through autodetection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select Auto Detect.

The page adjusts.

After you click the Apply button, the router automatically detects the information in the following fields:

User Manual38Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Connection Type: This field indicates the connection type that is detected.

•

Router’s IPv6 Address on WAN: This field shows the IPv6 address that is acquired

•

for the router’s WAN (or Internet) interface. The number after the slash (/) is the length of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no address is acquired, the field displays Not Available. However, not every IPv6 connection type shows the WAN address information.

Router’s IPv6 Address on LAN: This field shows the IPv6 address that is acquired

•

for the router’s LAN interface. The number after the slash (/) is the length of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no address is acquired, the field displays Not Available.

6. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive the IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

7. (Optional) Select the Enable RIPng check box.

This selection enables RIP Next Generation (RIPng) on IPv6 Internet connections. RIPng is an extension of Routing Information Protocol (RIP) that supports IPv6. You might want to enable RIPng if you are an advanced user with a complex home network configuration that requires dynamic routing.

8. (Optional) Select the Use This Interface ID check box and specify the interface ID to be used for the IPv6 address of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

9. Click the Apply button.

Your settings are saved.

Set a 6to4 tunnel IPv6 Internet connection

The remote relay router is the router to which your router creates a 6to4 tunnel. Make sure that the IPv4 Internet connection is working before you apply the 6to4 tunnel settings for the IPv6 connection.

User Manual39Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To set a 6to4 tunnel IPv6 Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select 6to4 Tunnel.

The page adjusts.

After you click the Apply button, the router automatically detects the information in the Router’s IPv6 Address on LAN field. This field shows the IPv6 address that is acquired for the router’s LAN interface. The number after the slash (/) is the length of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no address is acquired, the field displays Not Available.

6. Select a Remote 6to4 Relay Router radio button:

Auto: Your router uses any remote relay router that is available on the Internet.

•

This is the default setting.

Static IP Address: Enter the static IPv4 address of the remote relay router. Your

•

IPv6 ISP usually provides this address.

7. Select an IPv6 Domain Name Server (DNS) Address radio button:

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address. This option uses the DNS servers assigned by the ISP for the IPv6 connection.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

8. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive the IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

User Manual40Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

9. (Optional) Select the Use This Interface ID check box and specify the interface ID to be used for the IPv6 address of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

10. Click the Apply button.

Your settings are saved.

Set a pass-through IPv6 Internet connection

In pass-through mode, the router works as a Layer 2 Ethernet switch with two ports (LAN and WAN Ethernet ports) for IPv6 packets. The router does not process any IPv6 header packets.

To set a pass-through IPv6 Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select Pass Through.

The page adjusts, but no additional fields display.

6. Click the Apply button.

Your settings are saved.

User Manual41Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Set a fixed IPv6 Internet connection

To set a fixed IPv6 Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select Fixed.

The page adjusts.

6. Configure the fixed IPv6 addresses for the WAN connection:

IPv6 Address/Prefix Length: The IPv6 address and prefix length of the router

•

WAN interface.

Default IPv6 Gateway: The IPv6 address of the default IPv6 gateway for the

•

router’s WAN interface.

Primary DNS Server: The primary DNS server that resolves IPv6 domain name

•

records for the router.

Secondary DNS Server: The secondary DNS server that resolves IPv6 domain

•

name records for the router.

NOTE: If you do not specify the DNS servers, the router uses the DNS servers that are configured for the IPv4 Internet connection on the Internet Setup page. (See Manually set up the Internet connection on page 30.)

7. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive an IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

8. (Optional) Select the Enable RIPng check box.

User Manual42Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

9. In the IPv6 Address/Prefix Length fields, specify the static IPv6 address and prefix length of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

10. Click the Apply button.

Your settings are saved.

Set a DHCP IPv6 Internet connection

To set a DHCP IPv6 Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select DHCP.

The page adjusts.

After you click the Apply button, the router automatically detects the information in the following fields:

Router’s IPv6 Address on WAN: This field shows the IPv6 address that is acquired

•

Router’s IPv6 Address on LAN: This field shows the IPv6 address that is acquired

•

6. (Optional) In the User Class (If Required) field, enter a host name.

User Manual43Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Most people can leave this field blank, but if your ISP gave you a specific host name, enter it here.

7. (Optional) In the Domain Name (If Required) field, enter a domain name.

You can type the domain name of your IPv6 ISP. Do not enter the domain name for the IPv4 ISP here. If your ISP provided a domain name, type it in this field. For example, Earthlink Cable might require a host name of home, and Comcast sometimes supplies a domain name.

8. Select an IPv6 Domain Name Server (DNS) Address radio button:

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

9. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive an IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

10. (Optional) Select the Enable RIPng check box.

11. (Optional) Select the Use This Interface ID check box and specify the interface ID to be used for the IPv6 address of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

12. Click the Apply button.

Your settings are saved.

User Manual44Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Set a PPPoE IPv6 Internet connection

To set a PPPoE IPv6 Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select PPPoE.

The page adjusts.

After you click the Apply button, the router automatically detects the information in the following fields:

Router’s IPv6 Address on WAN: This field shows the IPv6 address that is acquired

•

Router’s IPv6 Address on LAN: This field shows the IPv6 address that is acquired

•

6. Configure the login settings:

a. In the Login field, enter the login information for the ISP connection.

This is usually the name that you use in your email address. Some ISPs (like Mindspring, Earthlink, and T-DSL) require that you use your full email address when you log in. If your ISP requires your full email address, type it in this field.

b. In the Password field, enter the password for the ISP connection.

c. In the Service Name field, enter a service name.

If your ISP did not provide a service name, leave this field blank.

User Manual45Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

NOTE: The default setting of the Connection Mode menu is Always On to

provide a steady IPv6 connection. The router never terminates the connection. If the connection is terminated - for example, when the modem is turned off

- the router attempts to reestablish the connection immediately after the PPPoE connection becomes available again.

7. Select an IPv6 Domain Name Server (DNS) Address radio button:

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address. This option uses the DNS servers assigned by the ISP for the IPv4 connection.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

8. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive the IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

9. (Optional) Select the Enable RIPng check box.

This selection enables RIP Next Generation (RIPng) on IPv6 Internet connections. RIPng is an extension of Routing Information Protocol (RIP) that supports IPv6.

10. (Optional) Select the Use This Interface ID check box and specify the interface ID to be used for the IPv6 address of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

11. Click the Apply button.

Your settings are saved.

User Manual46Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Use auto config for an IPv6 Internet connection

To set up an IPv6 Internet connection through auto configuration:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select Auto Config.

The page adjusts.

After you click the Apply button, the router automatically detects the information in the following fields:

Router’s IPv6 Address on WAN: This field shows the IPv6 address that is acquired

•

Router’s IPv6 Address on LAN: This field shows the IPv6 address that is acquired

•

6. (Optional) In the DHCP User Class (If Required) field, enter a host name.

Most people can leave this field blank, but if your ISP gave you a specific host name, enter it here.

7. (Optional) In the DHCP Domain Name (If Required) field, enter a domain name.

You can type the domain name of your IPv6 ISP. Do not enter the domain name for the IPv4 ISP here. For example, if your ISP’s mail server is mail.xxx.yyy.zzz, type xxx.yyy.zzz as the domain name. If your ISP provided a domain name, type it in this field. For example, Earthlink Cable might require a host name of home, and Comcast sometimes supplies a domain name.

8. Select an IPv6 Domain Name Server (DNS) Address radio button:

User Manual47Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address. Unless the ISP assigns DNS servers through DHCPv6, this option uses the DNS servers assigned by the ISP for the IPv4 connection.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

9. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive the IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

10. (Optional) Select the Enable RIPng check box.

This selection enables RIP Next Generation (RIPng) on IPv6 Internet connections. RIPng is an extension of Routing Information Protocol (RIP) that supports IPv6.

11. (Optional) Select the Use This Interface ID check box and specify the interface ID to be used for the IPv6 address of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

12. Click the Apply button.

Your settings are saved.

Set a 6rd IPv6 Internet connection

The 6rd protocol makes it possible to deploy IPv6 to sites using a service provider’s IPv4 network. 6rd uses the service provider’s own IPv6 address prefix. This limits the operational domain of 6rd to the service provider’s network and is under direct control of the service provider. The IPv6 service provided is equivalent to native IPv6. The 6rd mechanism relies on an algorithmic mapping between the IPv6 and IPv4 addresses that are assigned for use within the service provider’s network. This mapping allows for automatic determination of IPv4 tunnel endpoints from IPv6 prefixes, allowing stateless operation of 6rd.

With a 6rd tunnel configuration, the router follows the RFC5969 standard, supporting two ways to establish a 6rd tunnel IPv6 WAN connection:

Auto Detect mode: In IPv6 Auto Detect mode, when the router receives option 212

• from the DHCPv4 option, autodetect selects the IPv6 as 6rd tunnel setting. The router

User Manual48Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

uses the 6rd option information to establish the 6rd connection. For more information, see Use auto detect for an IPv6 Internet connection on page 38.

Manual mode: In 6rd mode, if the router receives option 212, the fields are

• automatically completed. Otherwise, you must enter the 6rd settings.

To set a 6rd IPv6 Internet connection:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > IPv6.

The IPv6 page displays.

5. From the Internet Connection Type menu, select 6rd.

The page adjusts.

After you click the Apply button, the router automatically detects the information in the following sections:

6rd (IPv6 Rapid Development) Configuration: The router detects the service

•

provider’s IPv4 network and attempts to establish an IPv6 6rd tunnel connection. If the IPv4 network returns 6rd parameters to the router, the page adjusts to display the correct settings in this section.

Router’s IPv6 Address on LAN: This field shows the IPv6 address that is acquired

•

6. If the router does not automatically detect the information in the 6rd fields, specify the following 6rd settings:

6rd Prefix: Type the IPv6 prefix that your ISP gave you.

•

6rd Prefix Length: Type the IPv6 prefix length that your ISP gave you.

•

6rd IPv4 Border Relay Address: Type the border router’s IPv4 address that your

•

ISP gave you.

6rd IPv4 Address Mask Length: Type the IPv4 mask length that your ISP gave

•

you.

7. Select an IPv6 Domain Name Server (DNS) Address radio button:

User Manual49Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Get Automatically from ISP: Your ISP uses DHCP to assign your DNS servers.

•

Your ISP automatically assigns this address. This option uses the DNS servers assigned by the ISP for the IPv4 connection.

Use These DNS Servers: If you know that your ISP requires specific servers, select

•

this option. Enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it also.

8. Select an IP Address Assignment radio button:

Use DHCP Server: Use this method if devices on the LAN cannot receive an IPv6

•

address through auto configuration but must receive the IPv6 address through a DHCP server.

Auto Config: This is the default setting.

•

This setting specifies how the router assigns IPv6 addresses to the devices on your home network (the LAN).

9. (Optional) Select the Use This Interface ID check box and specify the interface ID that you want to be used for the IPv6 address of the router’s LAN interface.

If you do not specify an ID here, the router generates one automatically from its MAC address.

10. (Optional) In the MTU Size (in bytes) field, enter a size in bytes.

The default size for this type of IPv6 connection is 1480 bytes.

11. Click the Apply button.

Your settings are saved.

Manage the MTU size

The maximum transmission unit (MTU) is the largest data packet a network device transmits.

MTU concepts

When one network device communicates across the Internet with another, the data packets travel through many devices along the way. If a device in the data path uses a lower maximum transmission unit (MTU) setting than the other devices, the data packets must be split or “fragmented” to accommodate the device with the smallest MTU.

The best MTU setting for NETGEAR equipment is often the default value. In some situations, changing the value fixes one problem but causes another. Leave the MTU unchanged unless one of these situations occurs:

User Manual50Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

You experience problems connecting to your Internet service, and the technical

• support of either the Internet service provider (ISP) or NETGEAR recommends

changing the MTU setting.

For example, if a secure website does not open, or displays only part of a web page, you might need to change the MTU.

You use VPN and experience severe performance problems.

•

You used a program to optimize MTU for performance reasons and now you are

• experiencing connectivity or performance problems.

CAUTION: An incorrect MTU setting can cause Internet communication

problems. For example, you might not be able to access certain websites, frames within websites, secure login pages, or FTP or POP servers.

If you suspect an MTU problem, a common solution is to change the MTU to 1400. If you are willing to experiment, you can gradually reduce the MTU from the maximum value of 1500 until the problem goes away. The following table describes common MTU sizes and applications.

Table 2. Common MTU sizes

ApplicationMTU

1500

The largest Ethernet packet size. This setting is typical for connections that do not use PPPoE or VPN and is the default value for NETGEAR routers, adapters, and switches.

Used in PPPoE environments.1492

Maximum size to use for pinging. (Larger packets are fragmented.)1472

Used in some DHCP environments.1468

Used in PPPoA environments.1458

Used in PPTP environments or with VPN.1436

Change the MTU size

To change the MTU size:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

User Manual51Specify Your Internet Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The BASIC Home page displays.

4. Select ADVANCED > Setup > WAN Setup.

The WAN Setup page displays.

5. In the MTU Size field, enter a value from 616 to 1500.

6. Click the Apply button.

Your settings are saved.

User Manual52Specify Your Internet Settings

Control Access to the Internet

The router comes with a built-in firewall that helps protect your home network from unwanted intrusions from the Internet.

This chapter contains the following sections:

• NETGEAR Armor

• Activate Armor using the Nighthawk app

• Network access control list

• Block Internet sites and services

• Set up security event email notifications

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

NETGEAR Armor

Your router supports NETGEAR Armor.

After you start your subscription, NETGEAR Armor protects your home network from potential cyber threats and provides complete data protection, advanced threat defense, webcam protection, multilayer ransomware protection, anti-phishing, safe files, secure browsing, rescue mode, anti-fraud, and anti-theft. In addition, NETGEAR Armor provides multiple performance and privacy tools.

NETGEAR Armor includes an anti-malware application for your Windows-based computers and your Mac OS, iOS, and Android devices.

For more information about NETGEAR Armor, visit netgear.com/landings/armor/default.aspx.

You can use the Nighthawk app to view and manage NETGEAR Armor.

Activate Armor using the Nighthawk app

To activate Armor using the Nighthawk app:

1. Launch the Nighthawk app.

The dashboard displays.

2. Tap Security.

The Security page displays.

If Armor was not yet activated, it is now activated automatically, or you are prompted to purchase Armor.

Network access control list

You can use the network access control list (ACL) on the router to block or allow access to your network and the Internet. The ACL identifies a WiFi or wired device by its MAC address. The router detects the MAC addresses of the devices on the network and either allows or denies access.

User Manual54Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The router detects and stores the MAC addresses of devices that connect to the network, so it lists the MAC addresses both of devices that are currently connected and any that were previously connected.

If you set up a network ACL that allows all new devices to connect, the following applies:

You can either select or manually enter devices that you want to block from

• connecting to the network.

All other devices are allowed access to the network.

•

If you set up a network ACL that blocks all new devices from connecting, the following applies:

You can either select or manually enter devices that you want to allow access to the

• network.

Devices that are currently connected to the network or that were allowed to connect

• in the past are automatically placed on the network ACL as allowed devices.

All other devices are denied access to the network.

•

NOTE: Each network device has a MAC address that serves as a unique identifier. The MAC address is a 12-character physical address, containing the hexadecimal characters 0–9, a–f, or A–F (uppercase or lowercase) only, and separated by colons (for example, 00:09:AB:CD:EF:01). Typically, the MAC address is on the label of a device. If you cannot see the label, you can display the MAC address using the network configuration utilities on your computer or mobile device.

Enable the network access control list, set the access rule, and allow or block connected devices

When you enable network access control, you must select whether new devices are automatically allowed to access the network or are blocked from accessing the network. By default, devices that are already connected to the network are added to the ACL as allowed, but you can choose to block one or more of these devices from accessing the network.

To enable and manage the network access control list for the entire network and allow or block connected devices:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

User Manual55Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Access Control.

The Access Control page displays.

5. Select the Turn on Access Control check box.

You must select this check box before you can select an access rule and use the Allow and Block buttons. When the Turn on Access Control check box is cleared, all devices are allowed to connect, even if a device is on the list of blocked devices.

6. Select an access rule to apply to new devices:

Allow all new devices to connect: With this setting, if you connect a new device

•

to the network, it can access the network. You do not need to enter its MAC address on this page. This option works for most home networks. You can also block one or more devices from accessing the network. For more information, see the following step.

Block all new devices from connecting: With this setting, if you want to allow

•

a new device to connect, you must enter its MAC address on this page. (In this situation, a new device is a device that was not previously connected to the network.) For more information about allowing one or more devices, see the following step.

If you block all new devices from connecting, the device that you are currently using to connect to the router web interface, any other devices that are currently connected to the network, and all devices that were allowed to connect to the network in the past are still allowed access. That means that these devices are automatically added to the network ACL as allowed devices. If you want to block any of these devices, see the following step.

NOTE: Selecting an access rule does not affect previously blocked or allowed devices. It applies only to new devices trying to access the network after you apply this setting.

7. To change access for devices that are connected or were connected to the network, do the following:

Currently connected devices:

•

In the table that contains the ACL, the Status column shows either Allowed or Blocked for a device. To change the status, select the check box for the device, and click either the Allow button or the Block button.

User Manual56Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

NOTE: If you blocked all new devices from connecting, make sure that

the computer or mobile device that you are currently using to access the router web interface shows as Allowed in the Status column.

Devices that were connected in the past:

•

To manage allowed devices that are currently not connected to the network,

○

see Manage allowed devices currently not on the network on page 57.

To manage blocked devices that are currently not connected to the network,

○

see Manage blocked devices currently not on the network on page 59.

8. Click the Apply button.

Your settings are saved.

Manage allowed devices currently not on the network

If you set up an access control list (ACL) that blocks all new devices from accessing the network, you can add new devices that must be allowed access to the network, remove old devices, or change whether devices that were allowed must now be blocked when they try to connect to the network.

For example, you could add a second computer or mobile device for access to the router web management interface in case the device that you are currently using needs to be removed from the network for repairs.

To manage allowed devices currently not on the network:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Access Control.

The Access Control page displays.

5. Click the View list of allowed devices not currently connected to the network link.

User Manual57Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

A table displays the detected device name, MAC address, and connection type of the devices that are not connected but allowed to access the network.

In the following steps, we refer to the list of allowed devices not currently connected to the network as the list of allowed devices.

6. To add a device to the list of allowed devices, do the following:

a. Click the Add button.

The Add Allowed Device page displays.

b. Enter the MAC address and device name for the device that you want to allow.

c. On the Add Allowed Device page, click the Apply button.

The device is added to the list of allowed devices.

7. To remove a device from the list of allowed devices, do the following:

a. Select the check box for the device.

b. Click the Remove from the list button.

The device is removed from the list of allowed devices.

8. To change the device status by blocking access for a device on the list of allowed devices, do the following:

a. Select the check box for the device.

b. Click the Edit button.

The Edit Device Name page displays.

c. From the Access Control menu, selected Block.

d. On the Edit Device Name page, click the Apply button.

The device is moved to the list of blocked devices not currently connected to the network.

9. To change the device name for a device on the list of allowed devices, do the following:

a. Select the check box for the device.

b. Click the Edit button.

The Edit Device Name page displays.

c. In the Device Name field, enter a name.

d. On the Edit Device Name page, click the Apply button.

The device name is changed on the list of allowed devices.

10. Click the Apply button.

Your settings are saved.

User Manual58Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Manage blocked devices currently not on the network

If you set up an access control list (ACL) that allows all new devices to access the network, you can add new devices that must be blocked from accessing the network, remove old devices, or change whether devices that were blocked must now be allowed when they try to connect to the network.

To manage blocked devices currently not on the network:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Access Control.

The Access Control page displays.

5. Click the View list of blocked devices not currently connected to the network link.

The Access Control page displays.

A table displays the detected device name, MAC address, and connection type of the devices that are not connected and are blocked from accessing the network.

In the following steps, we refer to the list of blocked devices not currently connected to the network as the list of blocked devices.

6. To add a device to the list of blocked devices, do the following:

a. Click the Add button.

The Add Blocked Device page displays.

b. Enter the MAC address and device name for the device that you want to block.

c. On the Add Blocked Device page, click the Apply button.

The device is added to the list of blocked devices.

7. To remove a device from the list of blocked devices, do the following:

a. Select the check box for the device.

b. Click the Remove from the list button.

User Manual59Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The device is removed from the list of blocked devices.

8. To change the device status by allowing access for a device on the list of blocked devices, do the following:

a. Select the check box for the device.

b. Click the Edit button.

The Edit Device Name page displays.

c. From the Access Control menu, selected Allow.

d. On the Edit Device Name page, click the Apply button.

The device is moved to the list of allowed devices not currently connected to the network.

9. To change the device name for a device on the list of blocked devices, do the following:

a. Select the check box for the device.

b. Click the Edit button.

The Edit Device Name page displays.

c. In the Device Name field, enter a name.

d. On the Edit Device Name page, click the Apply button.

The device name is changed on the list of blocked devices.

10. Click the Apply button.

Your settings are saved.

Block Internet sites and services

You can prevent access to specific Internet sites by defining keywords and domains (websites) that must be blocked. You can also block Internet services on your network from accessing the Internet.

Use keywords to block Internet sites

You can use keywords to block certain Internet sites from your network. You can use blocking all the time or based on a schedule.

NOTE: Keyword blocking only works for website URLs that begin with http:// only. It does not work for URLs that begin with https://.

User Manual60Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To block Internet sites:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Block Sites.

The Block Sites page displays.

5. Select when to block keywords:

Per Schedule: Turn on keyword blocking according to a schedule that you set.

•

For more information, see Schedule when to block Internet sites and services on page 64.

Always: Turn on keyword blocking all the time, independent of the Schedule

•

page.

6. In the Type keyword or domain name here field, enter a keyword or domain that you want to block.

For example:

Specify xxx to block http://www.badstuff.com/xxx.html and any site that includes

•

xxx, such as http://www.badxxxstuff.com and http://www.badstuffxxx.org.

Specify the domain suffix (for example, .com) if you want to block only sites with

•

a domain suffix such as .com. In such a situation, sites with domain suffixes such as .edu and .gov are still allowed.

Enter a period (.) to block all Internet browsing access.

•

7. Click the Add Keyword button.

The keyword is added to the keyword list. The keyword list supports up to 32 entries.

8. Click the Apply button.

Your settings are saved. Keyword blocking takes effect.

User Manual61Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Delete keywords from the blocked list

To delete keywords from the list:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Block Sites.

The Block Sites page displays.

5. Do one of the following:

To delete a single word, select it and click the Delete Keyword button.

•

The keyword is removed from the list.

To delete all keywords on the list, click the Clear List button.

•

All keywords are removed from the list.

6. Click the Apply button.

Your settings are saved.

Prevent blocking on a trusted computer

You can exempt one trusted computer from blocking. The computer that you exempt must be assigned a fixed IP address. You can use the reserved IP address feature to specify the IP address. See Manage reserved LAN IP addresses on page 97.

To specify a trusted computer:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

User Manual62Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The BASIC Home page displays.

4. Select ADVANCED > Security > Block Sites.

The Block Sites page displays.

5. Scroll down and select the Allow trusted IP address to visit blocked sites check box.

6. In the Trusted IP Address field, enter the IP address of the trusted computer.

7. Click the Apply button.

Your settings are saved.

Block services from the Internet

You can block Internet services on your network based on the type of service. You can block the services all the time or based on a schedule.

NOTE: Service blocking works only for services and applications that are using Transmission Control Protocol (TCP) or User Datagram Protocol (UDP) for communication.

To block services:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Block Services.

The Block Services page displays.

5. Select when to block the services:

Per Schedule: Turn on service blocking according to a schedule that you set.

•

For more information, see Schedule when to block Internet sites and services on page 64.

Always: Turn on service blocking all the time, independent of the Schedule page.

•

6. Click the Add button.

The Block Services Setup page displays.

User Manual63Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

7. To add a service that is in the Service Type menu, select the application or service.

The settings for this service automatically display in the fields.

8. To add a service or application that is not in the menu, select User Defined, and do the following:

a. If you know that the application uses either TCP or UDP, select the appropriate

protocol. Otherwise, select TCP/UDP (both).

b. Enter the starting port and ending port numbers.

If the service uses a single port number, enter that number in both fields. To find out which port numbers the service or application uses, you can contact the publisher of the application, ask user groups or newsgroups, or search on the Internet.

9. Select a filtering option:

Only This IP Address: Block services for a single computer.

•

IP Address Range: Block services for a range of computers with consecutive IP

•

addresses on your network.

All lP Addresses: Block services for all computers on your network.

•

10. Click the Add button.

Your settings are saved.

Schedule when to block Internet sites and services

When you schedule blocking, you can use the same schedule to block sites, block services, or block both. The schedule does not become active until you assign it to site blocking, service blocking, or both.

To set up a schedule for blocking:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > Schedule.

User Manual64Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The Schedule page displays.

5. Specify when the schedule is active:

Days to Block: Select the check box for each day that you want to enable

•

blocking, or select the Every Day check box, which automatically selects the check boxes for all days.

Time of Day to Block: Set a start and end time in 24-hour format, or select the

•

All Day check box for 24-hour blocking.

6. Click the Apply button.

Your settings are saved.

Set up security event email notifications

The router can email you its logs of router activity. The log records router activity and security events such as attempts to access blocked sites or services.

To set up email notifications:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Security > E-mail.

The E-mail page displays.

5. Select the Turn E-mail Notification On check box.

6. In the Primary E-mail Address field, type the email address to which logs and alerts must be sent.

This email address is also used for the From address. If this field is blank, log and alert messages are not sent.

7. (Optional) In the Secondary E-mail Address field, type a second email address to which logs and alerts must be sent.

8. In the Sender field, type the name that you want to show in the email as the sender.

User Manual65Control Access to the Internet

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

9. In the Your Outgoing Mail Server field, type the name of your ISP outgoing (SMTP) mail server (such as mail.myISP.com).

You might be able to find this information in the configuration window of your email program. If you leave this field blank, log and alert messages are not sent.

10. In the Outgoing Mail Server Port Number field, type a port number in the field.

If you do not know the port number, leave the default port number.

11. If your outgoing email server requires authentication, select the My mail server requires authentication check box, and do the following:

a. In the User Name field, type the user name for the outgoing email server.

b. In the Password field, type the password for the outgoing email server.

12. To send alerts when someone attempts to visit a blocked site, select the Send Alerts Immediately check box.

Email alerts are sent immediately when someone attempts to visit a blocked site.

13. To send logs based on a schedule, specify these settings:

a. From Send logs according to this schedule menu, select the schedule type.

b. From the Day menu, select the day.

If you select When log is full, Hourly, or Daily, the day setting does not apply.

c. From the Time menu, select the time, and select the am or pm radio button.

If you select When log is full or Hourly the time settings do not apply.

14. Click the Apply button.

Your settings are saved.

Logs are sent automatically according to the schedule that you set. If the log fills before the specified time, it is sent. After the log is sent, it is cleared from the router memory. If the router cannot email the log and the log buffer fills, the router overwrites the log.

User Manual66Control Access to the Internet

Manage WiFi Settings

You can customize the router’s WiFi settings.

The chapter includes the following sections:

• Change the name for a WiFi network

• Change the WiFi password or the WiFi security option

• Set up WPA/WPA2 Enterprise WiFi security

• Hide or broadcast the SSID for a WiFi network

• Enable or disable AX WiFi

• Enable or disable OFDMA

• Enable or disable Smart Connect

• Enable or disable 20/40 MHz coexistence for the 2.4 GHz radio

• Change the WiFi mode

• Change the 2.4 GHz or 5 GHz WiFi channel

• Change your country or region

• Set up a guest WiFi network

• Manage advanced WiFi settings

• Use the WPS Wizard for WiFi connections

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Change the name for a WiFi network

For each WiFi network, the WiFi network name (also referred to as the SSID) is randomly generated and is on the router label. You can change the default network name. The network name can be up to 32 characters long and is case-sensitive.

NOTE: If Smart Connect is enabled, the 2.4 GHz, 5 GHz, and 6 GHz radios use the same WiFi network name (SSID). To use a different SSID for each band, disable Smart Connect.

To change the name for a WiFi network:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. In the Name (SSID) field, enter a new name.

6. Click the Apply button.

Your settings are saved.

Change the WiFi password or the WiFi security option

The WiFi password is different from the admin password that you use to log in to the router.

Your router comes with preset WPA3 security, which is printed on the router label. We recommend that you use the preset security, but you can change the settings. We also recommend that you do not disable the WiFi security.

User Manual68Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To change the WiFi password or the WiFi security option:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. To change the 2.4 GHz or 5 GHz WiFi password, enter a new password in the Password (Network Key) field. The Password (Network Key) field displays for the following WiFi security options:

WPA2-PSK [AES]: Requires a password that contains 8 to 63 characters (or 64

•

hexadecimal characters).

WPA-PSK [TKIP] + WPA2-PSK [AES]: Requires a password that contains 8 to

•

63 characters (or 64 hexadecimal characters).

WPA3-PSK: Requires a password that contains 8 to 127 characters (or 128

•

hexadecimal characters).

WPA-PSK2 [AES] + WPA3-PSK: Requires a password that contains 8 to 63

•

characters (or 64 hexadecimal characters).

NOTE: By default, your password is hidden. To display your password, click the icon next to the Password field.

6. To change the WiFi security option for the 2.4 GHz or 5 GHz WiFi network, select a

Security Options radio button:

None: An open WiFi network that does not provide any security. Any WiFi device

•

can join the WiFi network. We recommend that you do not use an open WiFi network.

WPA2-PSK [AES]: Enables WiFi devices that support WPA2 to join the router’s

•

WiFi network. WPA2 provides a secure connection but some older WiFi devices do not detect WPA2 and support only WPA. If your network includes such older devices, select WPA-Personal [TKIP] + WPA2-Personal [AES] security.

WPA-PSK [TKIP] + WPA2-PSK [AES]: Enables WiFi devices that support either

•

WPA or WPA2 to join the router’s WiFi network. However, WPA-Personal [TKIP] is less secure than WPA2-Personal [AES] and limits the speed of WiFi devices to 54 Mbps.

User Manual69Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

WPA/WPA2 Enterprise: Requires that your WiFi network can access a RADIUS

•

server. For more information, see Set up WPA/WPA2 Enterprise WiFi security on page 70.

WPA3-PSK: The default setting, which enables WiFi devices that support WPA3

•

to join the WiFi network. WPA3 is the latest security standard, uses SAE encryption, and is more secure than WPA2. If all devices on your network support WPA3, we recommend that you keep this security option. If your network includes devices that do not support WPA3, select WPA2-PSK [TKIP] + WPA3-PSK security.

NOTE: If you did not change the WiFi password, the default password displays. The default password is printed on the router label.

WPA2-PSK [AES] + WPA3-PSK: Enables WiFi devices that support either WPA2

•

or WPA3 to join the router’s WiFi network. However, WPA2-PSK [AES] is less secure than WPA3-PSK.

7. Click the Apply button.

Your settings are saved.

Set up WPA/WPA2 Enterprise WiFi security

Remote Authentication Dial In User Service (RADIUS) is an enterprise-level method for centralized Authentication, Authorization, and Accounting (AAA) management. To enable the router to provide WPA and WPA2 enterprise WiFi security, the WiFi network that the router provides must be able to access a RADIUS server.

NOTE: If you use WPA/WPA2 Enterprise security, you cannot use Wi-Fi Protected Setup (WPS).

To set up WPA/WPA2 Enterprise security:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

User Manual70Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

4. Select Wireless.

The Wireless Setup page displays.

5. For the 2.4 GHz or 5 GHz WiFi network, select the WPA/WPA2 Enterprise radio button:

6. Specify the following settings:

Encryption mode: From the Encryption Mode menu, select the enterprise

•

mode:

WPA2 [AES]: WPA2 provides a secure connection but some older WiFi devices

○

do not detect WPA2 and support only WPA. If your network includes such older devices, select WPA [TKIP] + WPA2 [AES] security.

WPA [TKIP] +WPA2 [AES]: This type of security enables WiFi devices that

○

support either WPA or WPA2 to join the router’s WiFi network. This is the default mode.

RADIUS server IP Address: Enter the IPv4 address of the RADIUS server to which

•

the WiFi network can connect.

RADIUS server Port: Enter the number of the port on the router that is used to

•

access the RADIUS server for authentication. The default port number is 1812.

RADIUS server Shared Secret: Enter the shared secret (RADIUS password) that

•

is used between the router and the RADIUS server during authentication of a WiFi user.

7. Click the Apply button.

Your settings are saved.

Hide or broadcast the SSID for a WiFi network

By default, a WiFi network broadcasts its WiFi network name (also referred to as the SSID) so that WiFi clients can detect the SSID in their scanned network lists. For additional security, you can turn off the SSID broadcast and hide the SSID so that users must know the SSID to be able to join the WiFi network.

To hide or broadcast the network name for a WiFi network:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

User Manual71Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. Select or clear the Enable SSID Broadcast check box.

Selecting this check box enables broadcast of the SSID (the default setting) and clearing this check box hides the SSID.

6. Click the Apply button.

Your settings are saved.

Enable or disable AX WiFi

AX WiFi improves your network’s capacity, Internet upload and download speeds, and WiFi range by allowing WiFi traffic from different devices to be concurrently managed. To do this, AX WiFi can use Orthogonal Frequency-Division Multiple-Access (OFDMA), 4x4 multi-user MIMO, and intelligent scheduling.

AX WiFi is enabled by default.

To enable or disable AX WiFi:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. Select or clear the Enable AX check box.

Selecting this check box enables AX WiFi (the default setting) and clearing this check box disables AX WiFi.

6. Click the Apply button.

User Manual72Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Your settings are saved.

Enable or disable OFDMA

If AX WiFi is enabled (which it is by default), you can enable Orthogonal Frequency-Division Multiple-Access (OFDMA) for each radio band independently. By default, OFDMA is disabled in both radio bands, even when AX WiFi is enabled.

OFDMA allows data transmission signals to be split into smaller signals. Your router sends these small signals directly to individual devices in your network. Because multiple devices can be served in the same transmission window, your router can increase network speed and efficiency.

Note the following about OFDMA:

Enable OFDMA if your network includes many Internet of things (IoT) devices.

•

After you enable OFDMA, if you notice that some of your devices do not function

• as expected, disable OFDMA to see if the devices function normally.

If your network includes many older devices, you might want to keep OFDMA

• disabled.

To enable or disable OFDMA:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. Select or clear the Enable OFDMA in 2.4 GHz check box.

Selecting this check box turns on OFDMA in the 2.4 GHz radio band and clearing this check box turns off OFDMA in the 2.4 GHz radio band.

6. Select or clear the Enable OFDMA in 5 GHz check box.

Selecting this check box turns on OFDMA in the 5 GHz radio band and clearing this check box turns off OFDMA in the 5 GHz radio band.

7. Click the Apply button.

User Manual73Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Your settings are saved.

Enable or disable Smart Connect

Smart Connect selects the fastest WiFi band for your router. For Smart Connect to work, the 2.4 GHz and 5 GHz bands must use the same WiFi network name (SSID) and network key (password). That means that when you connect to the router with WiFi, you see only one SSID that connects to both bands.

NOTE: If you enable Smart Connect and the SSID and passwords for the 2.4 GHz and 5 GHz bands do not match, the WiFi settings for the 2.4 GHz band overwrite the WiFi settings for the 5 GHz band.

To enable or disable Smart Connect:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. Select or clear the Enable Smart Connect check box.

Selecting this check box enables Smart Connect and clearing this check box disables Smart Connect (the default setting).

6. Click the Apply button.

Your settings are saved.

Enable or disable 20/40 MHz coexistence for the 2.4 GHz radio

20/40 coexistence allows a 20 MHz and 40 MHz channel width to be supported simultaneously. By default, 20/40 MHz coexistence is enabled on the 2.4 GHz radio to

User Manual74Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

prevent interference between WiFi networks in your environment at the expense of WiFi speed. If no other WiFi networks are present in your environment, you can disable 20/40 MHz coexistence to increase the WiFi speed on the 2.4 GHz radio to the maximum supported speed for the WiFi mode.

20/40 MHz coexistence applies to the 2.4 GHz radio.

To enable or disable 20/40 MHz coexistence for the 2.4 GHz radio:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. Select or clear the Enable 20/40 MHz Coexistence check box.

Selecting this check box enables coexistence (the default setting) and clearing this check box disables coexistence.

6. Click the Apply button.

Your settings are saved.

Change the WiFi mode

The WiFi mode options for the 2.4 GHz and 5 GHz WiFi networks depend on whether AX WiFi is enabled. For more information about AX WiFi , see Enable or disable AX WiFi on page 72.

Change the WiFi mode if AX WiFi is enabled

To change the WiFi mode settings if AX WiFi is enabled:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

User Manual75Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. In the Wireless Network (2.4 GHz b/g/n/ax) section, select a WiFi mode from the

Mode menu.

Up to 54 Mbps: Allows 802.11ax, 802.11n, 802.11g, and 802.11b devices to

•

join the network but limits 802.11ax and 802.11n devices to functioning at up to 54 Mbps.

Up to 230 Mbps: Allows for reduced interference with neighboring WiFi

•

networks. Allows 802.11ax, 802.11n, 802.11g, and 802.11b devices to join the network but limits 802.11ax and 802.11n devices to functioning at up to 230 Mbps.

Up to 460 Mbps: Allows 802.11ax, 802.11n, 802.11g, and 802.11b devices to

•

join the network and allows 802.11ax and 802.11n devices to function at up to 460 Mbps. This mode is the default mode.

6. In the Wireless Network (5 GHz a/n/ac/ax) section, select a WiFi mode from the Mode menu.

Up to 286 Mbps: Allows 802.11ax, 802.11ac, 802.11n, and 802.11a devices to

•

join the WiFi network in the 5 GHz band but limits 802.11ax, 802.11ac, and

802.11n devices to functioning at up to 286 Mbps.

Up to 572 Mbps: Allows for reduced interference with neighboring WiFi

•

networks. Allows 802.11ax, 802.11ac, 802.11n, and 802.11a devices to join the WiFi network in the 5 GHz band but limits 802.11ax and 802.11ac devices to functioning at up to 572 Mbps.

Up to 1200 Mbps: Allows 802.11ax, 802.11ac, 802.11n, and 802.11a devices

•

to join the WiFi network in the 5 GHz band and allows 802.11ax and 802.11ac devices to function at up to 1200 Mbps. This mode is the default mode.

7. Click the Apply button.

Your settings are saved.

User Manual76Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Change the WiFi mode if AX WiFi is disabled

To change the WiFi mode settings if AX WiFi is disabled:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. In the Wireless Network (2.4 GHz b/g/n/ax) section, select a WiFi mode from the

Mode menu.

Up to 54 Mbps: Allows 802.11ax, 802.11n, 802.11g, and 802.11b devices to

•

join the network but limits 802.11ax and 802.11n devices to functioning at up to 54 Mbps.

Up to 145 Mbps: Allows for reduced interference with neighboring WiFi

•

networks. Allows 802.11ax, 802.11n, 802.11g, and 802.11b devices to join the network but limits 802.11ax and 802.11n devices to functioning at up to 145 Mbps.

Up to 300 Mbps: Allows 802.11ax, 802.11n, 802.11g, and 802.11b devices to

•

join the network and allows 802.11ax and 802.11n devices to function at up to 300 Mbps. This mode is the default mode if AX WiFi is disabled.

6. In the Wireless Network (5 GHz a/n/ac/ax) section, select a WiFi mode from the Mode menu.

Up to 173 Mbps: Allows 802.11ax, 802.11ac, 802.11n, and 802.11a devices to

•

join the WiFi network in the 5 GHz band of the network but limits 802.11ax,

802.11ac, and 802.11n devices to functioning at up to 173 Mbps.

Up to 400 Mbps: Allows for reduced interference with neighboring WiFi

•

networks. Allows 802.11ax, 802.11ac, 802.11n, and 802.11a devices to join the WiFi network in the 5 GHz band but limits 802.11ax and 802.11ac devices to functioning at up to 400 Mbps.

Up to 866 Mbps: Allows 802.11ax, 802.11ac, 802.11n, and 802.11a devices to

•

join the WiFi network in the 5 GHz band and allows 802.11ax and 802.11ac

User Manual77Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

devices to function at up to 866 Mbps. This mode is the default mode if AX WiFi is disabled.

7. Click the Apply button.

Your settings are saved.

Change the 2.4 GHz or 5 GHz WiFi channel

You can change the 2.4 GHz or 5 GHz WiFi channel.

In some regions, not all channels are available. Do not change the channel unless you experience interference (shown by lost connections or slow data transfers). If this happens, experiment with different channels to see which is the best.

When you use multiple access points, it is better if adjacent access points use different channels to reduce interference. The recommended channel spacing between adjacent access points is four channels (for example, for the 2.4 GHz radio, use channels 1 and 5, or 6 and 10).

NOTE: If you change the 2.4 GHz or 5 GHz channel, the change also applies to the guest network.

To change the WiFi channel:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. To change the 2.4 GHz or 5 GHz WiFi channel, select a channel number from the Channel menu in the Wireless Network (2.4 GHz b/g/n/ax) section, Wireless Network (5 GHz a/n/ac/ax) section, or in both sections.

6. Click the Apply button.

Your settings are saved.

User Manual78Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Change your country or region

In some countries, the router is sold with a preconfigured country or region setting and you might not be able to change it.

To view or change your country or region:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Wireless.

The Wireless Setup page displays.

5. From the Region menu, select your region.

In some locations, you cannot change this setting.

6. Click the Apply button.

Your settings are saved.

Set up a guest WiFi network

A guest WiFi network allows visitors to use the Internet without using your WiFi security password or with a different WiFi password. By default, the guest WiFi network is disabled. You can enable and configure the guest WiFi network for each WiFi band.

The WiFi mode of the guest WiFi network depends on the WiFi mode of the main WiFi network. For example, if you configure the WiFi mode for the main WiFi network as Up to 54 Mbps in the 2.4 GHz band, the guest WiFi network also functions in the Up to 54 Mbps mode in the 2.4 GHz band. The channel also depends on the channel selection of the main WiFi network. The router provides two default guest WiFi networks with the following names (SSIDs):

2.4 GHz guest WiFi network SSID: NETGEAR-Guest

•

5 GHz guest WiFi network SSID: NETGEAR-5G-Guest

•

User Manual79Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

By default, these networks are configured as open networks without security but are disabled. You can enable one or both guest networks. You can also change the SSIDs for these networks.

To set up a guest WiFi network:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select Guest Network.

The Guest Network Settings page displays.

5. Configure the following settings to set up a 2.4 GHz or 5 GHz guest WiFi network:

Enable Guest Network: By default, the guest WiFi network is disabled. To enable

•

the guest WiFi network for the 2.4 GHz or 5 GHz WiFi band, select the Enable

Guest Network check box.

Enable SSID Broadcast: By default, the router broadcasts the SSID of the WiFi

•

band so that WiFi stations can detect the WiFi name (SSID) in their scanned network lists. To turn off the SSID broadcast for the 2.4 GHz or 5 GHz guest WiFi network, clear the Enable SSID Broadcast check box.

Allow guests to see each other and access my local network: By default, WiFi

•

clients that are connected to the 2.4 GHz or 5 GHz guest WiFi network cannot access WiFi devices or Ethernet devices that are connected to the main WiFi network. To allow access to the main WiFi network, select the Allow guests to

see each other and access my local network check box.

Guest Wireless Network Name (SSID): The SSID is the 2.4 GHz or 5 GHz guest

•

WiFi network name. The default 2.4 GHz SSID is NETGEAR-Guest. The default 5 GHz SSID is NETGEAR-5G-Guest.

To change the SSID, enter a name of maximum 32 characters in the field. The SSID is case-sensitive.

6. Select a WiFi security option for the 2.4 GHz or 5 GHz guest WiFi network:

None: An open WiFi network does not provide any security. Any WiFi device can

•

join the guest WiFi network. This is the default setting for the guest WiFi network.

WPA2-PSK [AES]: Provides a secure and fast connection but some older WiFi

•

devices do not detect WPA2 and support only WPA. If your guest WiFi network includes these older devices, select WPA-PSK [TKIP] + WPA2-PSK [AES] security.

User Manual80Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To use WPA2 security, in the Password (Network Key) field, enter a phrase of 8 to 63 characters. To join the guest WiFi network, a user must enter this password.

WPA-PSK [TKIP] + WPA2-PSK [AES]: Enables WiFi devices that support either

•

WPA or WPA2 to join the guest WiFi network. However, WPA-PSK [TKIP] is less secure than WPA2-PSK [AES] and limits the speed of WiFi devices to 54 Mbps.

To use WPA-PSK [TKIP] + WPA2-PSK [AES] security, in the Password (Network Key) field, enter a phrase of 8 to 63 characters. To join the guest WiFi network, a user must enter this password.

WPA3-PSK: Enables WiFi devices that support WPA3 to join the guest WiFi

•

network. WPA3 is the latest security standard, uses SAE encryption, and is more secure than WPA2. If all devices on your guest WiFi network support WPA3, we recommend that you use this type of security.

To use WPA3 security, in the Password (Network Key) field, enter a phrase of 8 to 127 characters. To join the guest WiFi network, a user must enter this password.

WPA2 + WPA3: Enables WiFi devices that support either WPA2 or WPA3 to join

•

the guest WiFi network. This type of security is also referred to as WPA2-PSK/WPA3-PSK and uses SAE and AES encryption. WPA2-PSK (which uses AES) is less secure than WPA3 (which uses SAE).

To use WPA2 + WPA3 security, in the Password (Network Key) field, enter a phrase of 8 to 63 characters. To join the guest WiFi network, a user must enter this password.

7. Click the Apply button.

Your settings are saved.

Manage advanced WiFi settings

CAUTION: Take extra care changing advanced WiFi settings because incorrect

configuration might affect the WiFi function of the router.

Enable or disable a WiFi radio

A WiFi radio is the component inside your router that broadcasts WiFi signal. Each radio (for example, the 5 GHz) radio has its own WiFi broadcast.

You can log in to the router and enable or disable a WiFi radio. If all WiFi radios are off, you can still use an Ethernet cable for a LAN connection to the router.

User Manual81Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To enable or disable a WiFi radio:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Wireless Settings page displays.

5. Select or clear the Enable Wireless Router Radio check box for a radio.

Selecting this check box turns on the radio and clearing this check box turns off the radio.

By default, all radios are enabled.

6. Click the Apply button.

Your settings are saved.

Set up a WiFi schedule

You can turn off the WiFi signal from your router at times when you do not need a WiFi connection. For example, you might turn it off for the weekend if you leave town. You can set up multiple schedules, and you can set up separate schedules for the 2.4 GH and 5 GHz radios.

To set up a WiFi schedule for a radio:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Wireless Settings page displays.

User Manual82Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

5. Click the Add a new period button for a radio.

The Turn off wireless signal by schedule page displays.

6. Use the menus, radio buttons, and check boxes to set up a period during which you want to turn off the WiFi signal.

7. Click the Apply button.

The Wireless Settings page displays.

The new schedule displays in the table. (You can edit or delete the schedule.)

8. Select the Turn off wireless signal by schedule check box for the radio to activate the schedule.

Selecting this check box enables all WiFi schedules for the radio radio and clearing this check box disables all WiFi schedules for the radio. By default, no WiFi schedule is set up and the check box is disabled.

9. Click the Apply button.

Your settings are saved.

Enable or disable implicit beamforming

Beamforming shapes a directional WiFi signal aimed at a WiFi client based on the client’s location, as opposed to radiating the signal out in all directions. This feature improves WiFi range and performance. Client devices do not need to support beamforming to benefit from implicit beamforming.

To enable or disable implicit beamforming:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Wireless Settings page displays.

5. Scroll down and select or clear the Enable Implicit BEAMFORMING check box.

Selecting this check box enables implicit beamforming (the default setting). Clearing this check box disables implicit beamforming.

6. Click the Apply button.

User Manual83Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Your settings are saved.

Enable or disable MU-MIMO

Multiuser multiple input, multiple output (MU-MIMO) improves performance when many WiFi clients that are MU-MIMO-capable transfer data at the same time. For MU-MIMO to function, WiFi clients must support MU-MIMO (some older devices do not), and they must be connected to the 5 GHz WiFi band. This feature is enabled by default, but you can disable it.

To enable or disable MU-MIMO:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Wireless Settings page displays.

5. Scroll down and select or clear the Enable MU-MIMO check box.

Selecting this check box enables MU-MIMO (the default setting). Clearing this check box disables MU-MIMO.

6. Click the Apply button.

Your settings are saved.

Enable or disable PMF

Protected Management Frames (PMF) is a security feature that protects unicast and multicast management frames from being intercepted and changed for malicious purposes.

PMF is not enabled by default because some older devices do not support PMF.

To enable or disable PMF:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

User Manual84Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Wireless Settings page displays.

5. Scroll down and select or clear the Disable PMF check box.

Selecting this check box disables PMF (the default setting). Clearing this check box enables PMF.

CAUTION: If you enable PMF, devices that do not support PMF cannot

connect to the WiFi network.

6. Click the Apply button.

Your settings are saved.

Enable or disable airtime fairness

Airtime fairness ensures that all WiFi clients receive equal time on the network. Network resources are divided by time, so if you have five WiFi clients, they each get one-fifth of the network time. The advantage of this feature is that your slowest WiFi clients don’t control network responsiveness. This feature is enabled by default, but you can disable it.

To enable or disable airtime fairness:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Wireless Settings page displays.

5. Scroll down and select or clear the Enable AIRTIME FAIRNESS check box.

User Manual85Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Selecting this check box enables airtime fairness (the default setting). Clearing this check box disables airtime fairness.

6. Click the Apply button.

Your settings are saved.

Change the CTS/RTS threshold or preamble mode for a radio

For most WiFi networks, the CTS/RTS threshold and preamble mode work fine and we recommend that you do not change the settings. (In general, these settings are intended for WiFi testing.)

CAUTION: We recommend that you do not change these settings unless directed

by NETGEAR support or unless you are sure what the consequences are. Incorrect settings might disable the WiFi function of a radio unexpectedly.

NOTE: If the Smart Connect feature is enabled, the CTS/RTS threshold and preamble mode apply to all radios. That means that you cannot change the CTS/RTS threshold and preamble mode for each radio individually.

To change the CTS/RTS threshold or preamble mode for a radio:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Wireless Settings.

The Advanced Wireless Settings page displays.

5. In the CTS/RTS threshold (1-2347) field for a radio, enter a value from 1 to 2437.

The default value is 2347.

6. From the Preamble Mode menu for a radio, select the preamble mode:

Long Preamble: A long transmit preamble might provide a more reliable

•

connection or a slightly longer range.

Short Preamble: A short transmit preamble might give better performance.

•

User Manual86Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

CAUTION: Incorrect settings might disable the radio’s WiFi broadcast

unexpectedly.

7. Click the Apply button.

Your settings are saved.

Use the WPS Wizard for WiFi connections

WPS (Wi-Fi Protected Setup) lets you connect a WPS-enabled device to your WiFi network without typing the WiFi password. Instead, you push a software button in the router web interface or enter a PIN to connect.

If you use the push button method, the device that you are trying to connect must provide either a physical button or a software button. If you use the PIN method, you must know the PIN of the device that you are trying to connect.

NOTE: You cannot use the WPS Wizard to connect a device to a guest network.

Use the WPS Wizard with the push button

To use the push button method to connect a WiFi device to your WiFi network, the device must have either a physical button or a software button.

To use the WPS Wizard with the push button:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > WPS Wizard.

A note explaining WPS displays.

5. Click the Next button.

The Add WPS Client page displays.

User Manual87Manage WiFi Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

By default, the Push Button (recommended) radio button is selected.

6. Click the green WPS software button on the page.

7. Within two minutes, go to the WPS-enabled device and use its WPS software to connect to the WiFi network.

The WPS process automatically sets up the WPS-enabled device with the network password when it connects. The router web interface displays a confirmation message.

Use the WPS Wizard with a PIN

To use a PIN to connect a WiFi device to your WiFi network, you must know the PIN of the device.

To use the WPS Wizard with a PIN:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > WPS Wizard.

A note explaining WPS displays.

5. Click the Next button.

The Add WPS Client page displays.

By default, the Push Button (recommended) radio button is selected.

6. Select the PIN Number radio button.

7. In the Enter Clients' PIN field, enter the PIN of the device.

8. Click the Next button.

For four minutes, the router attempts to find the WiFi device.

9. Within four minutes, go to the WiFi device and use its WPS software to join the network without entering a password.

The WPS process automatically sets up the WPS-enabled device with the network password when it connects. The router web interface displays a confirmation message.

User Manual88Manage WiFi Settings

Manage the WAN and LAN Network Settings

You can customize the router’s wide area network (WAN) settings for the Internet port and local area network (LAN) settings for local devices. We recommend that you install the router and connect it to the Internet before you change its network settings.

This chapter contains the following sections:

• Manage the WAN settings

• Change the LAN IP address settings or RIP settings

• Set the IP addresses that the router assigns

• Disable the DHCP server feature in the router

• Manage reserved LAN IP addresses

• Manage custom static routes

• Set up an IPTV port or a bridge for a port group or VLAN tag group

• Manage Ethernet LAN port aggregation to a LAN device

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Manage the WAN settings

You can change security and other settings that determine how the router interacts with the Internet, also known as the wide area network (WAN).

Change the WAN security settings

The wide area network (WAN) security settings include port scan protection and denial of service (DoS) protection, which can protect your local area network (LAN) against many common cyber attacks. By default, DoS protection is enabled and a port scan is rejected.

You can also enable the router to respond to a ping to its Internet port. This feature allows your router to be discovered from the Internet. We recommend that you enable this feature only as a diagnostic tool or if a specific reason exists.

To change the default WAN security settings:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > WAN Setup.

The WAN Setup page displays.

5. To disable the protection for port scans and DoS attacks, select the Disable Port Scan and DoS Protection check box.

6. To enable the router to respond to a ping request from the Internet, select the Respond to Ping on Internet Port check box.

7. Click the Apply button.

Your settings are saved.

Network Settings

User Manual90Manage the WAN and LAN

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Set up a default DMZ server

The default DMZ server feature is helpful when you are using some online games and videoconferencing applications that are incompatible with Network Address Translation (NAT). The router is programmed to recognize some of these applications and to work correctly with them, but other applications might not function well. In some cases, one local computer can run the application correctly if the IP address for that computer is entered as the default DMZ server.

WARNING: DMZ servers pose a security risk. A computer designated as the

default DMZ server loses much of the protection of the firewall and is exposed to exploits from the Internet. If compromised, the DMZ server computer can be used to attack other computers on your network.

The router usually detects and discards incoming traffic from the Internet that is not a response to one of your local computers or is not accessing a service that you configured on the Port Forwarding/Port Triggering page. Instead of discarding this traffic, you can specify that the router forwards the traffic to one computer on your network. This computer is called the default DMZ server.

To set up a default DMZ server:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > WAN Setup.

The WAN Setup page displays.

5. Select the Default DMZ Server check box.

6. Type the IP address.

This must be a static IP address. For more information, see Manage reserved LAN IP addresses on page 97.

7. Click the Apply button.

Your settings are saved.

Network Settings

User Manual91Manage the WAN and LAN

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Manage IGMP proxying

IGMP proxying allows a computer on the local area network (LAN) to receive the multicast traffic (such as video streaming) it is interested in from the Internet. If you do not need this feature, leave it disabled, which is the default setting.

To enable IGMP proxying:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > WAN Setup.

The WAN Setup page displays.

5. Clear the Disable IGMP Proxying check box.

Clearing the Disable IGMP Proxying check box enables IGMP proxying and selecting the Disable IGMP Proxying check box disables IGMP proxying. By default, IGMP proxying is disabled.

6. Click the Apply button.

Your settings are saved.

Manage NAT filtering

Network Address Translation (NAT) filtering determines how the router processes inbound traffic. Secured NAT filtering blocks more unsolicited traffic from the Internet but might prevent some online games, point-to-point applications, or multimedia applications from working. Open NAT filtering provides a less secured firewall but allows almost all Internet applications to work. Secured NAT filtering is the default setting.

To change the default NAT filtering settings:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

User Manual92Manage the WAN and LAN

Network Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > WAN Setup.

The WAN Setup page displays.

5. Select a NAT Filtering radio button:

Secured: Blocks more unsolicited traffic from the Internet but might prevent

•

some Internet games, point-to-point applications, or multimedia applications from functioning. This is the default setting.

Open: Provides a less secured firewall but allows almost all Internet applications

•

to function.

6. Click the Apply button.

Your settings are saved.

Manage the SIP application-level gateway

The application-level gateway (ALG) for the Session Initiation Protocol (SIP) is enabled by default for enhanced address and port translation. However, some types of voice over IP (VoIP) and video traffic might not work well when the SIP ALG is enabled. For this reason, the router provides the option to disable the SIP ALG.

To disable the SIP ALG:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > WAN Setup.

The WAN Setup page displays.

5. Select the Disable SIP ALG check box.

Selecting the Disable SIP ALG check box disables the SIP ALG and clearing the Disable SIP ALG check box enables the SIP ALG. By default, the SIP ALG is enabled.

6. Click the Apply button.

User Manual93Manage the WAN and LAN

Network Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Your settings are saved.

Change the LAN IP address settings or RIP settings

The router is preconfigured to use private IP addresses on the local area network (LAN) side and to act as a Dynamic Host Configuration Protocol (DHCP) server. We also refer to the LAN IP address settings as the LAN TCP/IP settings. The router’s default LAN IP configuration is as follows:

LAN IP address: 192.168.1.1

•

Subnet mask: 255.255.255.0

•

These addresses are part of the designated private address range for use in private networks and are suitable for most applications. If your network requires a different IP addressing scheme, you can change these settings.

You might want to change these settings if you need a specific IP subnet that one or more devices on the network use, or if you use competing subnets with the same IP scheme.

Router Information Protocol (RIP) allows a router to exchange routing information with other routers on the same network.

To change the LAN IP address settings or RIP settings:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

5. To change the LAN IP address settings, do the following:

a. In the IP Address field, type the IP address.

b. In the IP Subnet Mask field, type the subnet mask of the router.

Network Settings

User Manual94Manage the WAN and LAN

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The IP address and subnet mask specify the IP address range that the devices on your network can use.

6. To change the RIP settings, do the following:

a. Select the RIP direction:

Both: The router broadcasts its routing table periodically and incorporates

• information that it receives.

Out Only: The router only broadcasts its routing table periodically.

•

In Only: The router only incorporates the RIP information that it receives.

•

b. Select the RIP version:

Disabled: This is the default setting.

•

RIP-1: This format is universally supported. It is adequate for most networks,

• unless you are using an unusual network setup.

RIP-2: This format carries more information. Both RIP-2B and RIP-2M send

• the routing data in RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M

uses multicasting.

7. Click the Apply button.

Your settings are saved.

If you changed the LAN IP address of the router, you are disconnected when this change takes effect.

8. To reconnect, close your browser, relaunch it, and log in to the router.

Set the IP addresses that the router assigns

By default, the router acts as a Dynamic Host Configuration Protocol (DHCP) server. The router assigns IP, DNS server, and default gateway addresses to all computers connected to the LAN. The assigned default gateway address is the LAN address of the router.

These addresses must be part of the same IP address subnet as the router’s LAN IP address. Using the default addressing scheme, define a range between 192.168.1.2 and 192.168.1.254, although you can save part of the range for devices with fixed addresses.

User Manual95Manage the WAN and LAN

Network Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To set the pool of IP addresses that the router assigns:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

5. Make sure that the Use Router as DHCP Server check box is selected.

6. Specify the range of IP addresses that the router assigns:

a. In the Starting IP Address field, type the lowest number in the range.

b. In the Ending IP Address field, type the number at the end of the range of IP

addresses.

7. Click the Apply button.

Your settings are saved.

The router delivers the following address information to any LAN device that requests a DHCP address:

An IP address from the range that you define

•

Subnet mask

•

Gateway IP address (the router’s LAN IP address)

•

DNS server IP address (the router’s LAN IP address)

•

Disable the DHCP server feature in the router

By default, the router acts as a DHCP server. The router assigns IP, DNS server, and default gateway addresses to all devices connected to the LAN. The assigned default gateway address is the LAN address of the router.

You can use another device on your network as the DHCP server or manually specify the network settings of all your devices.

User Manual96Manage the WAN and LAN

Network Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

To disable the DHCP server feature in the router:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

5. Clear the Use Router as DHCP Server check box.

6. Click the Apply button.

Your settings are saved.

7. (Optional) If this service is disabled and no other DHCP server is on your network, set your device IP addresses manually so that the devices can access the router and the Internet.

Manage reserved LAN IP addresses

When you specify a reserved IP address for a device on the LAN, that device always receives the same IP address each time it requests an IP address from the router's DHCP server (for example, when the device restarts). Assign reserved IP addresses to devices or servers that require permanent IP settings.

Reserve an IP address

To reserve an IP address:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

User Manual97Manage the WAN and LAN

Network Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

The BASIC Home page displays.

4. Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

5. In the Address Reservation section, click the Add button.

The Address Reservation page displays.

6. To reserve the IP address for a device that the router detects automatically, in the Address Reservation Table, select the radio button for the device.

7. To manually reserve an IP address for a device, do the following:

a. In the IP Address field, type the IP address to assign to the device.

Choose an IP address from the router’s LAN subnet, such as 192.168.1.x. (In a typical LAN subnet, IP addresses 192.168.1.0, 192.168.1.1, and 192.168.1.255 are reserved and cannot be used. 192.168.1.0 and 192.168.1.255 are not used by any devices.)

b. In the MAC Address field, type the MAC address of the device.

c. In the Device Name field, type a name for the device.

8. Click the Add button.

Your settings are saved. The reserved address is entered into the Address Reservation table on the LAN Setup page.

The reserved address is not assigned until the next time the device requests an IP address from the router’s DHCP server. Restart the device to force the device to request an IP address from the router.

Edit a reserved IP address

To edit a reserved address entry:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

Network Settings

User Manual98Manage the WAN and LAN

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

5. Select the radio button next to the reserved address that you want to edit.

6. Click the Edit button.

The Address Reservation page displays.

7. Change the settings.

8. Click the Apply button.

Your settings are saved.

Delete a reserved IP address entry

To delete a reserved address entry:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

5. Select the radio button next to the reserved address that you want to delete.

6. Click the Delete button.

The address is removed.

Manage custom static routes

For almost all Internet traffic, routes are automatically and dynamically selected. You can also set up a fixed, static route. Typically, you only need to add static routes when you have more than one router or multiple IP subnets on your network.

As an example of when a static route is needed, consider the following case:

Your main Internet access is through a cable modem to your ISP. The cable modem

• is connected to your router.

Your network also includes an ADSL router that you use to access a remote office

• site. This ADSL router is connected to a DSL modem, which is used on-demand only.

User Manual99Manage the WAN and LAN

Network Settings

Nighthawk WiFi 7 Dual-Band Router Model RS200, Model RS150v1

Your LAN subnet is 192.168.1.0, and the ADSL router’s address on your LAN is

•

192.168.1.100.

The public IP address range at the remote office site is 134.177.0.0.

•

When you set up your router, two implicit static routes were created:

1. A default route was created between your router and your ISP's gateway.

2. A second static route was created between your router and your LAN for all

192.168.1.0 addresses.

With this configuration, if you try to access a device on the 134.177.0.0 network at the remote office site, your router forwards your request to your ISP. In turn, the ISP forwards your request to the remote office site, where the firewall will deny the request.

In this situation, you must define a static route, telling your router to access 134.177.x.x addresses through your ADSL router at its LAN address of 192.168.1.100.

Here is an example static route setting for this configuration:

Destination IP address and subnet mask settings: The route applies to all addresses

• at the remote site, so set the destination IP address to 134.177.0.0 and the subnet

mask to 255.255.0.0.

Gateway IP address: Traffic for addresses in the 134.177.x.x network must be

• forwarded to the ADSL router, so set the gateway IP address to 192.168.1.100 (the

ADSL router’s address on your LAN).

Private route: Make the static route private as a security precaution in case Routing

• Information Protocol (RIP) is activated. A private route is not reported in RIP messages.

Active: Select the Active check box to ensure the route is active.

•

Metric: Set a low value for the metric (for example, 2).

•

Set up a static route

To set up a static route:

1. Launch a web browser from a computer or mobile device that is connected to the router network.

2. Enter http://www.routerlogin.net.

A login window displays.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified when you set up your router. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Static Routes.

Network Settings

User Manual100Manage the WAN and LAN

Netgear RS200 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Introduction

What is WiFi 7?

Additional documentation

Hardware Setup

Unpack your router

Front panel LEDs and buttons

Rear panel

Router label

Position your router

Cable your router

Connect to the Router Network and Access the Router

Connect to the router network

Connect to the router WiFi network

Connect to the router using a wired connection

Types of logins

Use a web browser to access the router

Automatic Internet setup

Log in to the router after you set up the router

Change the language

Install and manage your router with the Nighthawk app

Specify Your Internet Settings

Use the Setup Wizard

Manually set up the Internet connection

Set an Internet connection without a login

Set a PPPoE Internet connection

Set a PPTP or L2TP Internet connection

About high-speed Internet connections and Internet port aggregation

Get multi-gigabit Internet with Internet port aggregation

Set an IPv6 Internet connection

Types of IPv6 Internet connections

Requirements for entering IPv6 addresses

Use auto detect for an IPv6 Internet connection

Set a 6to4 tunnel IPv6 Internet connection

Set a pass-through IPv6 Internet connection

Set a fixed IPv6 Internet connection

Set a DHCP IPv6 Internet connection

Set a PPPoE IPv6 Internet connection

Use auto config for an IPv6 Internet connection

Set a 6rd IPv6 Internet connection

Manage the MTU size

MTU concepts

Change the MTU size

Control Access to the Internet

NETGEAR Armor

Activate Armor using the Nighthawk app

Network access control list

Enable the network access control list, set the access rule, and allow or block connected devices

Manage allowed devices currently not on the network

Manage blocked devices currently not on the network

Block Internet sites and services

Use keywords to block Internet sites

Delete keywords from the blocked list

Prevent blocking on a trusted computer

Block services from the Internet

Schedule when to block Internet sites and services

Set up security event email notifications

Manage WiFi Settings

Change the name for a WiFi network

Change the WiFi password or the WiFi security option

Set up WPA/WPA2 Enterprise WiFi security

Hide or broadcast the SSID for a WiFi network

Enable or disable AX WiFi

Enable or disable OFDMA

Enable or disable Smart Connect

Enable or disable 20/40 MHz coexistence for the 2.4 GHz radio

Change the WiFi mode

Change the WiFi mode if AX WiFi is enabled

Change the WiFi mode if AX WiFi is disabled

Change the 2.4 GHz or 5 GHz WiFi channel

Change your country or region

Set up a guest WiFi network

Manage advanced WiFi settings

Enable or disable a WiFi radio

Set up a WiFi schedule

Enable or disable implicit beamforming