Netgear RPS4000 Installation Manual

Check the LEDs

RPS ports

Installation Guide

Redundant Power System and Power Bank

Model RPS4000v2

The Redundant Power System and Power Bank RPS4000v2 provides power
system redundancy to external devices such as NETGEAR chassis switches,
managed switches, or smart switches with an RPS capability.

Each RPS4000v2 includes four power module bays, and can provide a maximum
output of 4000W when four APS1000W power supply units (PSU) are installed.
The RPS4000v2 can supply power to devices that support dynamic power
allocation as well as to legacy devices. The RPS4000v2 acts as a redundant power
system in 12 VDC context and acts as a power bank in PoE (56 VDC) context.

Package Contents

This package includes:

• Redundant Power System and Power Bank RPS4000v2

• AC power cable

• RPS cable, 60 cm (23.6 in.),16 pin

Power system indicators are listed in the following table:

Label Color Activity Description

PWR
(Power)

Power
Module
Status

RPS Port
Status

Green On Power is being provided to the RPS4000v2.

Green On An APS1000W is present and working properly.

Yellow On An APS1000W is present but is not working

properly.

Off Off There is no APS1000W present.

Green On The switch supports dynamic power allocation, and

the APS1000W in the corresponding RPS port and
power module bay is supplying power to the switch.

Blinking The switch supports dynamic power allocation, but

the APS1000W in the corresponding RPS port and
power module bay is not supplying power to the
switch. Power is being supplied by the APS1000W in
a different power module bay.

Yellow On The switch does not support dynamic power

allocation, and the APS1000W is providing power to
the switch.

Blinking The switch does not support dynamic power

allocation, but the APS1000W is not supplying
power to the switch.

Off Off No power is being supplied to the switch, or the

switch is not recognized.

Each RPS port on the RPS4000v2 can provide a maximum of 1440W at 56 VDC
and 200W at 11 VDC. Output power depends on the number of power supply
units (PSU) installed, and the settings of the Type selector and Current Share (CS)

selector on the back panel of the RPS4000v2.

To determine the RPS type for other switches, see the hardware installation guide
,which you can download by visiting netgear.com/support/download/.

Install the RPS4000v2

Install the RPS4000v2 in a standard 19-inch rack.

WARNING: Do not stack equipment, or place equipment in tight spaces or in

drawers. Be sure that your equipment is surrounded by at least 2 inches (5 cm) of
air space.

Insert a power supply unit

In models with more than one PSU, the PSUs are hot-pluggable.

1. If your switch functions with a single PSU only, disconnect the power cord
from the PSU and let the switch power down.

If your switch functions with more than one PSU, you do not need to power
down the switch and you can perform a hot swap.

2. Remove the PSU from the power module bay by moving the orange release
latch to the left and pulling the extraction handle.

3. Insert the replacement PSU into the power module bay, and gently push the
PSU into the bay until the latch locks.

CAUTION: When inserting the PSU, do not use unnecessary force. Doing so

can damage the connectors on the back of the PSU and on the midplane.

4. Connect the end of the power cord to the power receptacle on the PSU.

To install the RPS4000v2:

1. Attach the supplied mounting brackets to the side of the RPS4000v2.

2. Use the provided Phillips head screws to fasten the brackets to the sides of
the RPS4000v2.

Connect a switch to the RPS4000v2

WARNING: To prevent an electrical hazard, make sure that the RPS AC power

cord is not connected to the RPS before you install an APS1000W PSU or connect
the RPS to a switch.

Support and Community

Visit netgear.com/support to get your questions answered and access the latest
downloads.

3. Tighten the screws with a No. 1 Phillips screwdriver to secure each bracket.

4. Align the bracket and rack holes. Use two pan-head screws with nylon
washers to fasten each bracket to the rack.

5. Tighten the screws with a No. 2 Phillips screwdriver to secure the switch in
the rack.

Check the installation

Before you apply power, perform the following checks:

1. Inspect the equipment thoroughly.

2. Verify that all cables are installed correctly.

3. Check cable routing to ensure that cables are not damaged and do not
create a safety hazard.

4. Be sure that all equipment is mounted properly and securely.

1. Make sure an APS1000W PSU is installed into the power module bay on the
RPS4000v2.

2. Connect a switch to the corresponding RPS port.

3. Based on the RPS specication for the switch, set the position for the Type
and CS selectors on the back panel of the RPS4000v2. See the RPS4000v2

Hardware Installation Guide for conguration instructions.

4. Connect the switch to the RPS port on the RPS4000v2 using a NETGEAR RPS
cable (60 cm, 16 pin).

5. Power on the APS1000W that is connected to the switch.

Specications

Technical Specications

RPS port interface 4 NTGR RPS ports, 16 pin

Power 100–240 VAC, 50–60 Hz

Dimensions (H x W x D) 1.7 x 17.32 x 16.92 in. (43 x 440 x 430 mm)

Weight 12.8 lbs (5.8 kg)

Operating temperature 0° to 50°C (32° to 104°F)

Operating humidity 90% maximum relative humidity, noncondensing

Safety agency
approvals

UL, LVD, CB

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Regulatory and Legal

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
français canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian
French at https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of
Conformity, visit https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at

https://www.netgear.com/about/terms-and-conditions. If you do not agree, return

the device to your place of purchase within your return period.

March 2020

© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.

NETGEAR, Inc.

350 East Plumeria Drive
San Jose, CA 95134, USA

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3
University Technology Centre
Curraheen Road, Cork,
T12EF21, Ireland