Netgear FS309T Quick Start Manual

Introduction

The NETGEAR®Model FS309T Fast Ethernet Switch provides you
with a low-cost, high-performance network solution and is designed
to support power workgroups operating at either 10 megabits per
second (Mbps) or 100 Mbps, and can relieve server and backbone
bottlenecks with one copper Gigabit Ethernet port.

Verify Package Contents

Product Illustration

Auto Uplink™

The Auto Uplink technology that NETGEAR has included in this
product will automatically sense whether the straight-through cable
plugged into any port should have a ‘normal’ connection, e.g.
connecting to a PC; or an ‘uplink’ connection, e.g. connecting to a
router, switch, or hub. That port will then configure itself to the correct
configuration. This feature also eliminates the need to worry about
crossover cables, as Auto Uplink will accommodate either type of
cable to make the right connection.

Note: Auto Uplink will compensate for setting uplink
connections, and crossover or straight-through cables.
Using Auto Uplink to create multiple paths between any
two network devices will disable your network.

LEDs

This table describes the activity of the Model FS309T switch LEDs.

Label Activity Description Color

PWR On The Switch is receiving power Green

Off The Switch is NOT receiving power

100M/10M On Indicates Link or Activity at 10 Mbps

or 100 Mbps

• 100 Mbps speed Link GREEN

• 100 Mbps speed Activity

GREEN-Blinking

• 10 Mbps speed Link YELLOW

• 10 Mbps speed Activity

YELLOW-Blinking

1000M On Indicates Link or Activity at

1000 Mbps

• 1000 Mbps speed Link GREEN

• 1000 Mbps speed Activity

GREEN-Blinking

FDX/COL On Full Duplex GREEN

Collision

YELLOW-Blinking

Applications

Desktop Switching

The Model FS309T switch, used as a desktop switch to build a small
network that enables users to have Gigabit (1000 Mbps) access to a
server.

Segment Switching

The Model FS309T switch can segment a network into multiple
connected pieces, increasing overall bandwidth and throughput. The
Model FS309T switch segmenting networks that are built with a
NETGEAR Model FE508 Fast Ethernet Hub and a NETGEAR Model
DS516 Dual Speed Hub.

Preparing the Site

Before you begin installing your switch, prepare the installation site.
Make sure that your operating environment meets the operating
environment requirements of the equipment.

Characteristic Requirement

Temperature Ambient temperature between 0 and 40 C

(32 and 104 F). No nearby heat sources such as
direct sunlight, warm air exhausts, or heaters.

Operating humidity Maximum relative humidity of 90%,

noncondensing.

Ventilation Minimum 2 inches (5.08 cm) on all sides for

cooling. Adequate airflow in room or wiring closet.

Operating conditions At least 6 feet (1.83 m) to nearest

source of electromagnetic noise (such as
photocopy machine).

Power Adequate power source within 6 feet (1.83 m).

Installing the Switch

Set the switch up on a flat surface; you do not need any special tools.
Be sure the switch is positioned with at least 2 inches of space on all
sides for ventilation.

Connecting Devices

To connect devices to the switch:

1. Connect the devices to the 10/100 Mbps ports on the switch,
using Category 5 UTP cable and an RJ-45 plug.

Note: Ethernet specifications limit the cable length
between your PC or server and the switch to 328 feet
(100 meters)

2. Connect one end of the Category 5 UTP cable to the Gigabit
port and the other end to the linking server or network device.

3. Connect one end of the AC power cord to the power receptacle
on the rear panel of the switch and the other end of the AC
power cord to the wall outlet.

Verifying Installation

When power has been applied to the switch:

• The green Pwr (power) LED on the front panel is on.

When the switch is connected and operating, refer to the table in
“LEDs” for information about the LEDs and their activity.

Troubleshooting Information

Symptom Cause Solution

Power LED No power is Check the power cord connections
is off. received at for the switch and the connected

the hub. device.

Check for a defective adapter card,
cable, or port by testing them in an
alternate environment where all
products are functioning.

Make sure all cables used are
correct and comply with Ethernet
specifications.

Either 10M, Port connection Check the crimp on the RJ-45
100M, or 1000M is not connectors, and make sure that the
Link LED is off functioning. plug is properly inserted and locked

into the port at both the switch and
the connecting device.

Make sure all cables used are
correct and comply with Ethernet
specifications.

One or more Not all system Test the components in an
components are components are alternate environment where all
malfunctioning. properly installed. other components are functioning

properly.

A segment or One or more Verify that the cabling is correct.
device is not devices are not Be sure all cable connectors are
recognized as properly securely positioned in the required
part of the connected or ports. Straight-through cables
network. cabling does not should be used for all standard

meet Ethernet twisted pair connections.

guidelines. Make sure all devices are

connected to the network.
Equipment may have been
accidentally disconnected.

Technical Specifications

Type Specification

Standards ISO/IEC 802-3 (ANSI/IEEE 802.3i) 10BASE-T
Compatibility Ethernet

IEEE 802.3u,100BASE-TX Fast Ethernet
IEEE 802.3ab, 1000BASE-T Gigabit Ethernet
compatible with major network software, including
Windows

®

networking, NetWare, and Linux

Data Rate 100 Mbps with 4B/5B encoding and MLT-3

physical interface for 100BASE-TX
10 or 100 or 1000 Mbps half-duplex
20 or 200 or 2000 Mbps full-duplex

Network Interface RJ-45 connector for 10BASE-T or 100BASE-TX

or 1000BASE-T Ethernet interface

Power 3.7 w max

Physical Specifications

Dimensions: 25.3 x 3.5 x 18.0 cm

Weight: 2.86 lb; 1.30 kg

Environmental Specifications

Operating 0 to 40° C (32 to 104° F)
temperature:

Operating 90% maximum relative humidity,
humidity: noncondensing

Electromagnetic CE mark, commercial; FCC Part 15, Class A;
Compliance EN 55 022 (CISPR 22), C-Tick, VCCI A

Safety Agency CE mark, Commercial
Approvals for UL listed (UL 1950)
the Power Adapter

Performance Specifications

Frame filter rate: 14,800 frames/sec max for 10M port

148,000 frames/sec max for 100M port
1,480,000 frames/sec max for 1000M port

Frame forward 14,800 frames/sec max for 10M port
rate: 148,000 frames/sec max for 100M port

1,480,000 frames/sec max for 1000M port

Network latency 100 Mbps to 100 Mbps: 9.5 µs max
(using 64-byte 100 Mbps to 1000 Mbps: 8.5 µs max
packets): 1000 Mbps to 100 Mbps: 3.2 µs max

Address 4000 MAC addresses
database size:

Addressing: 48-bit MAC address

Queue buffer: 128 kilobytes

1

2

3

4

Model FS309T
Fast Ethernet Switch

Installation Hardware

Installation Guide,
Warranty & Registration Card
and Support Information Card

Power code

(for switch)

Front Panel of the Model FS309T Switch

10M/100M

Link, Activity LED

10/100Mbps

Fast Ethernet Switch

with Gigabit Port

9 87654321

Gigabit Port

Ethernet

PWR

Rear Panel of the Model FS309T Switch

1 2 3 4 5 6 7 8 9

Power
LED

10/100M Port Power Socket

GREEN = 100M, YELLOW = 10M, BLINKING = ACT

GREEN = FDX, YELLOW = COL

1000M
Link, Activity LED

1000M

MODEL

FS309T

FDX LED
Collision LED

100-240VAC, 50-60Hz

9462FA

Key

1000 Mbps
100 Mbps
10 Mbps

Server with Model GA302T
Gigabit Card

9 87654321

Model FS309T Switch

100-240VAC, 50-60Hz

9607FA

Key

1000 Mbps
100 Mbps
10 Mbps

Model FE508
Fast Ethernet Hub

Server with Model GA302T
Gigabit Card

9 87654321

Model FS309T Switch

100-240VAC, 50-60Hz

Model DS516
Dual Speed Hub

9608FA

© 2001 by NETGEAR, Inc. All rights reserved.

Trademarks

NETGEAR is a registered trademarks of NETGEAR, Inc. in the United States and in
other countries. Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. All other trademarks and registered trademarks are the properties
of their respective owners. All rights reserved. Information subject to change without
notice.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability,
NETGEAR reserves the right to make changes to the product described in this document
without notice.
NETGEAR does not assume any liability that may occur due to the use or application of
the product(s) or circuit layout(s) described herein.

Certificate of the Manufacturer/Importer

It is hereby certified that the NETGEAR Model FS309T Fast Ethernet Switch has been
suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991
and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in
accordance with the regulations may, however, be subject to certain restrictions. Please
refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this
equipment on the market and has been granted the right to test the series for compliance
with the regulations.

VCCI Statement

This equipment is in the Class A category (information equipment to be used in a
residential area or an adjacent area thereto) and conforms to the standards set by the
Voluntary Control Council for Interference by Data Processing Equipment and Electronic
Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read instructions for correct handling.

Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause
undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commerical environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

EN 55 024 Declaration of Conformance

This is to certify that the NETGEAR Model FS309T Fast Ethernet Switch is shielded
against the generation of radio interference in accordance with the application of Council
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 024
Class A (CISPR 22).

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (NETGEAR Model FS309T Fast Ethernet Switch) does not exceed
the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio
Interference Regulations of the Canadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des
Communications

Cet appareil numérique (NETGEAR Model FS309T Fast Ethernet Switch) respecte les
limites de bruits radioélectriques visant les appareils numériques de classe A prescrites
dans le Règlement sur le brouillage radioélectrique du ministère des Communications du
Canada.

10/100/1000 Mbps Fast Ethernet FS309T

Fast Ethernet Switch with Gigabit Port

Installation Guide

NETGEAR, Inc.

4500 Great America Parkway

Santa Clara, CA 95054

USA

Phone: 1-888-NETGEAR

E-mail: [e-mail]

www.NETGEAR.com

Support Information

See Support Information Card for phone numbers.

Internet / World Wide Web

Go to http://www.NETGEAR.com for the NETGEAR Web page.

Defective or damaged merchandise can be returned to your point-of-sale representative.

IMPORTANT!

Please register online. YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE

RETAIN PROOF OF PURCHASE and this warranty information.To register your product, get product

support, or to obtain product information and NETGEAR product documentation, direct your Web

browser to the http://www.NETGEAR.com Web page. If you do not have access to the World Wide

Web, you can register your product using the enclosed registration card and mail it to NETGEAR

customer service.

November, 2001

M-FS309TNA-0