Page 1
Nero 15cm Desk Fan
Code: 749015
INSTRUCTION MANUAL
AC220-240V 50Hz 16W
BEFORE OPERATING THIS PRODUCT, READ, UNDERSTAND, AND
FOLLOW THESE INSTRUCTIONS.
BEFORE FIRST USE
Read and follow all the instructions in this “Use And Care” manual even if you feel you are
familiar with the products, and find a place to keep it handy for future reference.
Your attention is drawn particularly to the sections conc erning “IMPORTANT SAFEGUARDS”
IMPORTANT SAFEGUARDS
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT.
When using the electrical appliance, the following basic safety precautions should always be
followed.
WARNING- to reduce the risk of fire, electric shock or injury to persons or property:
Always operate the product from a power source of the same voltage, frequency and
rating as indicated on the product identification plate.
Do not use this fan with any solid state speed control device to reduce the risk of electric
shock.
The appliance is not intended for use by persons (including children) with reduced
physical, sensory, mental capabilities or lack of experience and knowledge, unless they
have been given supervision or instructions concerning use of the appliance by a person
responsible by their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not leave the fan running unattended.
Do not operate the product if it is dropped, damaged or showing signs of product
malfunction. Do not operate the product with a damaged plug or cord. Return the
complete product to the place of purchase for inspection, refund or replacement.
If it is not working properly, contact a qualified electrician or service centre for examination
and repair, never try to dismantle it by yourself.
Do not immerse or expose the product or flexible cord to rain, moisture or any other liquid.
This product should not be used in the immediate vicinity of water, such as bathtubs,
washbowls, swimming pools etc. where the likelihood of immersion or splashing could
occur.
Page 2
Never install the unit where it could be subject to:
Heat sources such as radiators, heat registers, stoves or other products that produce
heat
Direct sunlight
Mechanical vibration or shock
Excessive dust
Lack of ventilation, such as a cabinet or bookcase
Uneven surface
Switch off and unplug from outlet when the product is not in use, before assembling or
disassembling parts and before cleaning. Fully assemble the fan before switching on.
Avoid contact with moving parts. Do not insert any body parts (e.g. finger) or objects
through the grill when the fan is operating.
Do not cover the grille, or operate in close proximity to curtains, etc.
This product is intended for normal domestic/household use only.
Always disconnect the fan when moving it from one location to another.
The use of attachments or accessories not recommended or sold by the product
distributor may cause personal or property hazards or injuries.
Be sure fan is on a stable surface when operating to avoid overturning.
Do not immerse in water.
If the supply cord is damaged,it must be replaced by the manufacturer or its service
agent,or similarly qualified person,in order to avoid a hazard.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
.
PRODUCT ASSEMBLY
Loosen the Adjusting Screw by turning it anti-clockwise until it totally comes out of the M6
Screw Nut.
Place the extension under the motor unit into the slot of the Base
Align the two connecting pieces such that their holes are in line.
Penetrate the Adjusting Screw through the holes of the two connecting pieces
Fasten by turning the Adjusting Screw clockwise.
OPERATION OF THE PRODUCT
CAUTION:
Select a suitable location for the fan. Always choose a safe location in accordance to the
safety recommendations outlined.
When placing a fan on a table or shelf, always ensure that the power cord does not hang
where it can accidentally be pulled and that the unit cannot accidentally fall.
Do not hang or mount the fan on a wall or ceiling.
1. On / Off and Speed Control
The ON/Off and Speed is controlled by the Turning Switch, which is located on the rear motor
housing indicated in the above diagram.
0- The Fan is switched Off
1- The Fan operates at the lowest speed
2- The Fan operates at the highest speed
2. Angle Adjustment
Switch off the fan. Slightly loosen the Adjusting Screw by turning it anti-clockwise. Adjust the fan
to the desired angle and then tighten the Adjusting Screw by turning it clockwise.
CLEANING
Switch off and unplug from the power supply before assembling or disassembling and
cleaning.
Keep the air vents at the rear of the main body free from dust or fluff– use a vacuum
cleaner to remove these when necessary. Do not probe any opening to remove fluff.
Fan component parts should be cleaned using mild soap and a damp cloth or sponge. Do
not allow any water or other liquid to enter the motor housing.
Thoroughly remove soap film with clean water.
CAUTION: Do not use harsh detergents, chemical cleaners or solvents as they may
damage the surface finish of the fan components.
Imported By R. Weatherdon & Co Pty Ltd
Sydney - Australia
www.weatherdon.com.au
Made in China
Loading...