Page 1
Attention:
1. Please read the owner’s ma n ual before using this product.
2. Do not fill iron with any ot her liqu id except water.
3.
The iron must not be left unattended while it is connected to the
supply mains.
4. The plug must be removed from the socket out l et b efo r e th e w at er
reserv oir is fill ed with water.
5. When setting the iron on support, be sure the support is stable.
6. Do not use the iron if it's broken or damaged after dropping. The
appliance is not to be used by children or persons with reduced
physi cal, s ensory or me ntal ca pabilit ies or la ck of exper ience a nd
knowledge, unless they have been given supervision or instruction.
Cautions:
1. Make sure that the applied voltage is the same as the rating
voltage.
2. If the supply cord is damaged,
it must be replaced by the
manufa c t ur er, s ervi c e a g ent or qu a li fi ed persons i n order to a vo i d a
hazard.
3. This ir on is for h ousehol d use only.
4. Do not immerse the iron i nto any li quid for cleaning.
5. Do not touch the hot metal plate, hot water, or steam to avoid
scalding.
Main technical parameters:
Type Rated voltage
Rated
frequency
Rated p ow e r
R-338 220-240V 50/60Hz 2000-2400W
Nero Steam Iron
Code: 742700 Ceramic
Code: 742715 Stainless Steel
Please read these instructions before
use and
view the illustrations before using this
appliance.
Page 2
Characteristics and structure:
A: Soleplate
I: Top handle
B: Skirt J: Cord guard
C: Handle K: Clean button
D: Spray nozzle L: Temperatu re dial
E: Water tank
M: Pilot light
F: Fill co ver
N: Rear cov er
G: Steam knob O: Water tank cover
H: Spr ay & burst of steam button
Filling water:
1. Before filling with water, please pull out the plug first.
2. Set the steam control to the minimum position.
3. Pull down the cover of water filling mouth, and then fill with water.
Spraying:
Press t he s pra y bu tt on, and water will spray o ut f r om t he spr a y n ozzle.
Always keep enough water in the water tank.
Steam ironing:
1. To use stea m ironi ng, t urn t he stea m cont rol t o mini mum p ositi on
and set the temperature control at the ‘…’ or MAX position.
2. When the indica tor light goes out, t urn the stea m control to the
suitable position.
Burst of steam:
Set the temperature control at the ‘…’ or MAX pos ition, t hen press
down the burst of steam button.
Dry ironing:
Turn the st eam cont rol to minimu m positi on, then s et the temperature
control to the suitable position.
Self cleaning:
Fill with water, then plu g the ir on into t he mains . Set the temperature
contr ol t o t he max i mu m position. About 3 minutes lat er, press t he sel f clea n
button for about 1 minute. Steam an d h ot wa ter wi ll b e s pra ye d t o cl e an t h e
steam chamber. For best results use this function once every two weeks.
Anti-drip:
This ir on is eq uip ped wit h a dr ip sto p func tio n: the ir on a utomat ical ly
stops steaming when the temperature is too low to prevent water from
dripping out of th e sol eplate.
Anti-calc:
The anti-ca lc function filtrates the mi neral s from t he wate r to pre vent
mineral residue build up in the steam chamber.
Automatic shut o ff:
If the iron is switched on and not moved for a period of 8 minutes while
standing on its heel,
or 30 seconds while standing on the soleplate, an
internal safety feature will switch the iron off a nd t he au to shut off in dica tor
will blink. Move the appliance sharply to switch it on again.
Storage:
Page 3
After using, pull out the plu g a nd pour out the r emaini ng water. Turn
the st eam co ntrol t o and the temperature control to ‘min’. Let the iron cool
down, then store the iron vertically in a sa fe a n d dr y pl a c e .
Imported By R. Weatherdon & Co Pty Ltd
Sydney - Australia
www.weatherdon.com.au
Made in China
Loading...