Neff T29R96N0NL User Manual [de]

Assembly instructions

please keep

Einbauanleitung

bitte aufbewahren

Instructions dassemlage

veuillez conserver

Istruzioni di montaggio

si prega di conservare

Instrucciones de montaje

por favor, guardar

Installatievoorschrift

s.v.p. bewaren

Instruçoes de montagem

por favor, guardar

Montaj talimatlarý

lütfen saklayýnýz

min.

480

520

min.

5030

30 50

880

915

min.

30 50

490

520-530

915

61,8

600

min.50

490

150

850

650 min.

150

850 x 490

880 x 490 880 x 500

850 x 500

7 mm.

Put these instructions in a safe place for future reference

Instructions for the installation technician

All operations connected with the installation, adjustment and adaptation of this unit to another type of gas must be carried out by authorised personnel from our Technical Services Department, and should observe the current regulations and instructions of gas companies.

IMPORTANT: Before you begin, turn off the

gas and electricity supply to the appliance.

Before connecting up the appliance to the installation, first check that it has been adjusted for the type of gas with which it is to be supplied. Our cooking hobs leave the factory designed to function with the type of gas that is indicated on the specifications plate.

It is of the utmost importance that the place in which the appliance is installed has suitable ventilation in accordance with regulations. so that the combustion gases are piped outside.

Check the dimensions of the cooking hob as well as the dimensions of the hole to be cut in the kitchen unit.

The panels located above the work surface, right next to the cooking hob, must be made of non-inflammable material. Both the stratified surfacing and the glue used to secure it should be heat resistant, to prevent deterioration.

No electrical cables should come into contact with hot areas.

The power cable must be secured to the furniture module to prevent it from touching any hot parts of the oven or the cooking hob.

All appliances containing any electrical components must be earthed. This appliance must be installed in accordance with the current regulations and always in a wellventilated space. Read these instructions before installing or using the appliance.

Handle the appliance with care during the entire installation process. Do not knock the appliance.

In the event that this advice is not followed, the installation technician will be responsible for any damage caused, and the manufacturer will be exempt from all responsibility.

Installing the cooking hob in the furniture module

The option to locate the cooking hob in the kitchen unit (in accordance with the regulation for gas appliances EN 30-1 ) is Type 3.

Fitting measurements

- Minimum distances (mm). Cut an aperture of the necessary dimensions in the work surface. Fig. 1. *Measurements for warm glass hobs. Follow the instructions for the installation of cooker hoods.

- The wood fibres that have been used to

make the cooking hob modules tend to swell quite quickly when they come into contact with moisture. We therefore recommend that the cut edges are treated with a special glue to protect them from steam or any condensation that might drip down beneath the work surface of the cooker unit.

Depending on the model, the clips and the watertight seal (underside of the cooking hob) may already be fitted; if this is the case, do not under any circumstance remove them. The seal ensures that the entire work surface will be watertight, and prevents water seepage.

If this item has not been fitted in the factory, remove the pan supports and the gas burners covers and diffusers from your cooking hob, and turn it upside down. Now fit the adhesive seal supplied with the appliance onto the lower edge of the cooking hob, remove the

the attached accessories bag and them into the lateral orifices that are

provided for this purpose (see Fig. 3).

-1

staples from

secure

If no oven is installed under an electrical or mixed (gas and electric) hob, place a

separator of non-flammable material e.g. plywood or metal at a distance of 10 mm. from the bottom of the hob to prevent access to the lower part of the hob. If no oven is installed under a gas hob, it is suggested to place a separator of nonflammable material e.g. plywood or metal at a distance of 10 mm. from the bottom of the hob to prevent access to the lower part of the hob. In the event that a drawer is located beneath the appliance, please make sure that the drawer contains no heat-sensitive or easily combustible objects, such as spray cans or shoe polish. Use a heat-resistant utility drawer only.

To install the hob over an oven, check the

dimensions given in the installation manual.

- Press down all around the edges so that the cooking hob is supported along its entire perimeter (Fig. 4). Place the cooking hob in the middle of the hole where it is to be inserted into the kitchen unit.

Tighten the 6 securing clips (Fig. 3) and firmly screw it to the kitchen unit. Never remove them! The appliance is supplied ready to be installed in an 850 x 490 mm hole. If the hole you wish to insert it into is a different size (850 x 500, 880 x 490 or 880 x 500), use the centring pieces that are available from our technical assistance service (code 493716) as shown in Fig. 3.

- The end of the gas hob's inlet collector

has a

/2" thread, Fig. 5. This thread ensures:

A rigid connection. A copper pipe, a bolt and a watertight seal are supplied together with the cooking hob.

If you need to connect the gas supply horizontally, our technical services department can supply you with an adaptor (code 173018) and a seal (code 034308).

Connection using a metal pipe. In this case, it is necessary to install the accessory 9000060077 and the seal (034308) between the outlet of the manifold and the gas supply. Fig. 5a. With this option, you must prevent the pipe from coming into contact with moving parts of the insertion unit (for example, a drawer) or access to any spaces which might become obstructed

If you need to connect the gas supply horizontally, our technical services department can supply you with an adaptor (code 173018) and a seal (code 034308).

To be able to use this appliance in France, it is necessary to carry out a direct connection to the outlet of the manifold with the seal 034308. Fig. 5b. The position of the gas pipe, relative to the hole in the kitchen unit where it is to be fitted is shown in Fig. 1b.

Make sure that all the connections that have been installed are airtight. The manufacturer accepts no responsibility for leaks or for connections carried out by the installation technician.

5 - The following must be checked on the specifications plate: the voltage and the total power. This appliance must be earthed.

Always make certain that all connections that have been installed are in accordance with national legal requirements. Observe all the requirements of the local electrical supply company.

In order to meet standard safety regulations, the installation technician must provide an omnipolar cut-off switch with a contact separation of at least 3 mm. This is not necessary if the connection is made via a plug, so long as the user has access to it.

Our cooking hobs are provided with a power cable with or without a plug.

All appliances fitted with plugs should only be connected up to sockets which have been correctly earthed.

This appliance is type "Y", which means that the input cable MUST NOT BE CHANGED BY THE USER, only by the service technician for that particular make. The section and type of cable must be observed.

Do not make any adjustments in the interior of the appliance. If this should be necessary, call our technical assistance service. Types of cables: Power cable:

cooking hob:

All gas 3 x 0.75 mm

Changing gas type

All operations related to the installation, adjustment and adaptation of this unit to another type of gas must be carried out by authorised personnel from our Technical Services Department, and current gas company regulations and instructions must be observed.

IMPORTANT: Before you begin, turn off the gas and electricity supply to the appliance.

Provided that national laws so permit, this cooking hob may be adapted to function with other types of gas. To do so, all the following steps should be carried out:

) Change the hob burner tips (Table 1).

- Remove the pan supports, covers and

the main body of the burner.

2 - Change the burner tips using a 7 mm socket spanner and make sure that they are tightened all the way in order to ensure that they are correctly sealed. Fig. 6. With these burners the air does not have to be adjusted.

) Adjust the burner taps for reduced

consumption.

1 - Turn the taps down to minimum.

2 - Remove the control knobs from the taps. Fig. 7.

3 - Remove the anti-spillage disc seals.

If your cooking hob is fitted with exterior plastic disc seals, remove them by inserting a screwdriver through the discs' central orifice and levering them out. Fig. 8.

 When you have removed the disc seals from the orifice the control shaft emerges from, you will find an interior seal made of flexible rubber; you only need to press this with the tip of a screwdriver to clear the path to the tap adjusting screw. Do not remove the interior disc seal.

 If your cooking hob is only fitted with soft plastic inner disc seals, remove them with a screwdriver by levering them around the edge in order to gain access to the adjusting screw. 4 - Adjust the By-pass screw. Depending on the type of gas you wish to change the appliance to, you must perform one of the following processes, marked A, B, C and D:

A - The By-pass screws must be fully done

up. Fig. 10.

B - The By-pass screws must be loosened

until the correct flame is achieved. Fig. 11.

C - The By-pass screws that are fitted on the appliance must be substituted for the ones that are supplied in the transformation kit.

D - In this case, you must not alter the Bypass screws. In all cases, after the gas changeover has been carried out, make sure that the burner flames are correct by ensuring that when you go from the maximum setting to the minimum they do not go out and there is no flame backdraught. Consult Table 2 in order to find out which case applies to you: A, B, C or D.

5 - It is important to make sure that all the seals are in place in order to ensure that, in the case of spillages on the hob, there are no short circuits.

6 - Replace the control knobs on the taps.

Do not dismantle the tap shaft: In the event

of a malfunction, change the whole tap.

C) Place the sticker indicating that the appliance's gas supply has been changed next to the specifications plate.

+ 11 hidden pages