NEFF T29R96N0AU/01 Installation Instruction
This cooktop is for use with Natural Gas and LPG
Neff GmbH
Carl-Wery-Stra
81739 München
Cod. 9
000235447
e 34
ß
B
T29R8
N0AU
Dear customer,
We would like to thank and congratulate you for your choice.
This practical modern appliance has been made using materials of
the highest quality, which have been put through the strictest of
Quality Controls during manufacture and meticulously tested to
ensure that they meet all of your cooking demands.
We kindly ask you to read and follow these simple instructions
in order to guarantee first-class results from the very start. This
booklet contains important information not only concerning use,
but also concerning your own personal safety and maintenance of
the appliance.
Our products need to be carefully packed to protect them during
transportation. All the material used for packing is considered
essential for this purpose and is also completely recyclable. You
too can contribut towards protecting the environment by disposing
of this material at your nearest recyclable refuse collection point.
Do not dispose of used cooking oil down the kitchen sink. Oil may
seriously damage the environment. Dispose of it in a closed container
at your nearest collection point or, failing this, dispose of it in your
rubbish bin. Although this last solution is far from perfect, your oil
will be taken to a controlled refuse dump where it will not be allowed
to pollute water. You and your children will appreciate it.
Render your old appliance useless before disposing of it at your
nearest recyclable refuse collection centre.
Your local authority will be pleased to inform you where your nearest
centre is.
2
CONTENT
For your safety
What to do if yo smell gas
Warnings
Installation
Preparing to install
Clearances
Installation of cooktop into Kitchen bench
Installation procedure
Connection
Electrical connection
Gas connection
Conversion front Nat. Gas to LPG
To change injectors
Injector size chart
Minimum flame adjustment
Operating instructions
Burner location
Burner ignition & control
On and residual heat display
User instructions
Warnings concerning cooking
Cleaning and maintenance
Service
Trouble shooting
On indicators and fault messages
Wiring diagram
4Safety considerations
4
4
4
6
6
7
7
8
9
9
10
11
11
12
12
13
13
13
14
14 Automatic ignition system
15
17
18
19
19
20
21
3
Safety considerations
For your safety
What to do if you
smell gas
Warnings
• If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal
injury or death.
• Do not store articles on or against this appliance.
• Do not store flammable material near this appliance.
• Do not spray aerosols in the vicinity of this appliance while
it is in operation.
• Do not try to light the appliance.
• Do not touch any electrical switch; do not use any phone
in your building.
• Inmediately call your gas supplier from a neighbour’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier , call the fire department.
• Installation and service must be performed by an authorised
person.
1. Do not allow the flame to extend beyond the edge of the
cooking utensil. This instruction is based on safety considerations.
2. Do not forget that the unit becomes hot when in use.
Common sense is important. Just because the flame is out,
does not mean parts cannot still be hot.
3. This appliance shall not be used for space heating.
This instruction is based on safety considerations.
4. Be sure to disconnect the electrical supply before disassembly of the appliance.
5. Keep the appliance area clear and free from combustible
materials, gasoline and other flammable vapours and liquids.
6. This appliance must be installed in a position with the proper
level of ventilation. Do not obstruct the flow of combustion and
ventilation air.
7. Cabinets installed above the gas cooktop must have a
minimum clearance of 650 mm (24”).
8. The gas pressure regulator supplied with the appliance
must be installed in line with the gas pipe. (N.G. only)
9. For pressure testing in excess of 3.5 kPa (1/2 psig) the
appliance and its individual shutoff valve must be disconnected
from the gas suply piping system.
4
10. Important. When using a very large pot, leave a gap of at
least 50 mm (2”) to avoid damaging any parts in bench top
wood, plastic or other non-heat resistant materials. Never leave
oil or hot fat unattended.
11.The surfaces on heating and cooking appliances get hot
when in use. Be careful. Keep children away from the
appliance.
12.Only use your appliance for the preparation of food and
never
for room-heating purposes.
13.This appliance leaves the factory set for the gas supply
indicated on the data label. Call the Service Centre
to be altered.
14. Do not tamper inside the appliance. If necessary, call your
local Service Centre.
15. Overheated fat or oil can easily catch fire. Never leave the
appliance unattended when cooking food with fat or oil, e.g.
chips.
16. Never pour water on burning fat or oil. DANGER OF
Cover the receptacle to smother the flames and turn
BURNS!
the hob off.
17. In the event of a fault, cut the gas and electricity supplies
to the appliance. Call our Service Centre to repair the fault.
18. Do not use unstable or uneven-based receptacles on
cooking plates or burners. They may accidentally tip over.
19. If a gas supply knob/valve jams, do not force it. Call your
official Service Centre immediately for them to repair or replace
it.
20. The illustrations used in this booklet are only intended as
a guide.
21. Grids become very hot during use. When operating the
appliance control knobs, take care not to make contact
with the grids.
22. Do not use this appliance neither in marine craft nor in
caravans.
This appliance is not intented for the use by young children or
infirm persons without supervision. Young children should
be supervised to ensure they do not play with this appliance.
Make sure you keep these instructions for use and assembly in
a safe place, so that you can hand them on with the
appliance if it ever changes owner.
Note: To avoid jeopardising the electrical safety of the appliance,
it is forbidden to use high-pressure or steam jet cleaning
devices.
if it needs
SHOULD THE RELEVANT CONDITIONS NOT BE
PROPERLY SATISFIED, THE INSTALLER, AND NOT
THE MANUFACTURER, SHALL HELD LIABLE.
5
Installation
Statutory
requirements
Preparing to
install
This installation must conform with the following:
• Manufacturer’s Installation instructions
• Local Gas Fitting Regulations
• Municipal Building Codes
• Gas Installations Standard - AS 5601
• S.A.A. Wiring Code
• Local Electrical Regulations
• Any other statutory regulations
Refer to the Gas Installations Standard for piping size
details. These built-in hobs are intended to be
inserted in a benchtop cutout.
Only authorised personnel should connect
the appliance.
Before you begin, turn off the gas and electricity supply.
Installation dimensions are shown in Fig.1.
520-530
LPG
880
Pressure
80
test point.
915
45
27
490
61,8
Natural gas
130
Pressure
test point
m
i
n
3
0
/
min. 100
850
+
-
1
m
a
x
60
min.50
+
490
1
-
min. 600
45
Gas inlet
connection
1
Before connecting the unit, check whether the local
connection conditions (type of gas) are compatible with
the unit’s setting. Observe any special conditions imposed
by local suppliers (utilities). The specifications of this
cooktop are stated on the data label located on the
bottom of the cooktop base.
A duplicate data label is supplied for adhesion to
an accessible location near the hotplate if the data
label on the base of the hotplate cannot be
accessed when the hotplate is installed.
6
Clearances
Installation of
cooktop into the
kitchen bench
A range hood fitted above the top must be installed
according to the installation instructions for the range
hood. A minimum distance of 650 mm is required for a
range hood and 750 mm for an exhaust fan.
Any adjoining wall surface situated within 200mm from the
edge of any hob burner must be a suitable non-combustible material for a height of 150mm for the entire
length of the hob. Any combustible construction above
the hotplate must be at least 650mm above the top of
the burner and no cons
above the top of the
A minimum depth of 50mm from the top of the
surface must be provided for the appliance.
If the base of the hotplate can be touched, a protecting
shield must be fitted. This shield must be at least
10mm from the lowest part of the hotplate and must
be capable of withstanding the appliance temperatures.
Minimum thickness of benchtop is 30 mm. See Fig. 2.
2
Installation procedure:
Side clearances:
periphery of the
is less than
accordance
1. For cutout dimensions and clearances refer
2. a) If the clamps and the selfadhesive seal (lower edge
of the hob) are already fitted (depending on the model),
do not under any circumstance remove them. The seal
keeps the entire work surface watertight and prevents
spilage from leaking into cupboards underneath. Slightly
losen the retaining screws of the clamps positioned at
the bottom of the cooktop.
b ) If the clamps and the selfadhesive seal have not
been fitted in the factory, remove the pan support and
the gas burner covers from your cooking hob and turn it
upside down. Now fit the selfadhesive seal supplied
with the appliance onto the lower edge of the hob. Take
the clamps and screw them into the lower point designed
for this purpose. See Fig. 3.
200 mm, the surface shall be protected in
with clauses 5.12.1.1 & 5.12.1.2 of AS 5601.
truction shall be within 4 50mm
burner
If the distance measured from the
nearest burner to any vertical surface
.
worktop
30 mm
minimum
Fig.1.
7
Loading...