NEFF S5943X2GB/15 Use Instruction

en
Short and handy: everything your dishwasher needs...
Before using for the first time, read the Installation and Operating Instruc­tions!
Add salt.
Setting the water softening system *
Find out the water hardness at your water utility company and
enter below
* only before using the
dishwasher for the first time or if the water hard­ness changes
Dissolves limescale (not required for set value 0!)
Read off the setting
0–6
0–11
0–8
7–14 15–21 22–35
12–25 26–37 38–62
9–18 19–26 27–44
0–1.1
1.2–2.5
2.6–3.7
3.8–6.2
Quickly sorted
and then select a setting
SettingdH fH Clarke mmol/l
0
1
2
3
ABC
Reset
– Hold down programme button B and switch on the main
switch, then release the buttons. The . display flashes and buttons A and B illuminate (water hardness setting was set to 2 at the factory).
– Each time button B is depressed, the setting increases by
one (0-3). If buttons A, B and C illuminate, the maximum water hardness setting has been reached. If the water hardness setting is now increased again, the lights go out and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
Brief Instructions: Dishwasher
Add rinse-aid.
Add detergent.
Select programme.
Unscrew the lid.
Only before using the dishwasher for the first time pour approx. 1 l / 1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz salt (never deter­gent!)
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1, lift up lid 2.
Pour in rinse aid.
Very dirty dishes, a lot of detergent ...
If required, open the lid (press the pin).
Warning,
combination products are not suitable for all programmes, follow manufac­turer’s instructions.
Pour in detergent.
Quick, economical or intensive ...
Overview of programmes
This overview indicates the max. possible number of programmes. The programmes which correspond to your appliance can be found on your appliance fascia.
The programme data are values measured in the laboratory in compliance with Standard EN 50242. Deviations is practice are possible.
Duration in minutes Power consumption in kWh Water consumption in litres
Intensive Normal Eco Quick Prerinse
109
1,35
20
104
1,15
17
155
0,80
13
Screw on the lid. Switch on dishwasher immediately.
Close the lid. CLICK!
Push the lid shut, press. PLOP!
35 50 70 65
30
0,50
10
20
0,10
4
5 600 047 370 (8205) 450J
Switch appliance ON, off we go...
Press main switch, choose programme. Close door.
Switch appliance OFF, everything OK...
Signal sounds, open door. End-of-programme indicator flashes, press main switch.
Maintenance and care
For perfect rinsing results
Filters
Check and, if required, clean:
Spray arms
Remove blockages/ deposits
Breakdown and assistance
Problem Possible causes Remedy
Water left in the appliance Appliance not working/ stopst ...
Appliance not working/ stops ...
Pull up lower arm Unscrew upper arm Clean under running
The correct procedure
The appliance was opened during the programme ...
No / too little water check whether ...
Rotate filter cylinder, remove filter system
Close the appliance and switch it on, or stop the programme (see Stopping the programme).
the water supply is turned on. the supply fittings are not obstructed or furred up. the supply hose is not bent.
Rinse under running water
water (if required, use a toothpick)
Problem Possible causes Remedy
Plastic parts/crockery discoloured ...
Milky deposits on the crockery (removable) ...
Use a milder cleaning agent ... Too little cleaning agent ...
Rinsing agent dose too high (streaks visible) ... Rinsing agent dose too low ...
Insert Screw on filter
Insert lower arm Screw on upper arm
Use a cleaning agent containing chlorine bleach. Refer to the manufacturer’s instructions.
Reduce or increase the dosage according to the instructions.
system. NOTE MARK!
The crockery is not clean ...
There are powdery or greasy residues on the crockery ...
Crockery is stacked too closely together/on top of each other ... Too little cleaning agent ...
Wrong programme ... The spray arms are obstructed
The filter is loose ... The filter is dirty ...
The spray arm nozzles are blocked ... Too little water ...
Reload according to the instructions. Refer to the manufacturer’s instructions. Select the appropriate programme. Rearrange items causing a blockage (e.g. large spoons).
Clean the filter (see above) secure the filter correctly (MARKING). Clean the filter (see above). Clean the spray arms (see above).
See “Appliance is no longer working”.
Interrupting the programme ... Terminating the programme ...
Open the door.Press the START/STOP
button.
– To continue, press the
START/STOP button again.
Close the door.
Open the door.Press the two RESET
buttons simultaneously (approx. 3 seconds) (RESET).
– Close the door.
Glasses cloudy/dull ...
Rust on the cutlery ...
After 1 minute the programme ends. The ”signal sounds and the standby indicator illuminates”.
Switch off the appliance.
Water too hard ... Glasses not dishwasher-proof ... Unsuitable cleaning agent ...
Cutlery not rustproof ...
You will find further information in the instructions for use ... you may be able to solve the problem yourself.
Refill the special salt/ adjust water softening system. Use dishwasher-proof glasses. Use a glass-enhancing cleaning agent.
Use dishwasher-proof cutlery.
Arranging dishes correctly ...
Arrange dishwasher-proof dishes in accordance with the operating manual (without residual ash, wax, lubricating grease, ink, sticky labels; remove any large remnants of jam, milk products or food) and check that the spray arms can rotate freely.
Loading...