Additional information on products, accessories, replacement
parts and services can be found at www.neff-
international.com and in the online shop www.neff-
eshop.com
3
: Important safety information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for
future use or for subsequent owners.
This appliance is only intended to be fully
fitted in a kitchen. Observe the special
installation instructions.
Check the appliance for damage after
unpacking it. Do not connect the appliance
if it has been damaged in transport.
Only a licensed professional may connect
appliances without plugs. Damage caused
by incorrect connection is not covered
under warranty.
This appliance is intended for domestic use
only. The appliance must only be used for
the preparation of food and drink. The
appliance must be supervised during
operation. Only use this appliance indoors.
This appliance may be used by children
over the age of 8 years old and by persons
with reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with the appliance.
Children must not clean the appliance or
carry out general maintenance unless they
are at least 8 years old and are being
supervised.
Keep children below the age of 8 years old
at a safe distance from the appliance and
power cable.
Always slide accessories into the cooking
compartment correctly. See "Description of accessories in the instruction manual.
Risk of fire!
■
Combustible items stored in the cooking
compartment may catch fire. Never store
combustible items in the cooking
compartment. Never open the appliance
door if there is smoke inside. Switch off
the appliance and unplug it from the
mains or switch off the circuit breaker in
the fuse box.
Risk of fire!
■
A draught is created when the appliance
door is opened. Greaseproof paper may
come into contact with the heating
element and catch fire. Do not place
greaseproof paper loosely over
accessories during preheating. Always
weight down the greaseproof paper with a
dish or a baking tin. Only cover the
surface required with greaseproof paper.
Greaseproof paper must not protrude over
the accessories.
Risk of burns!
■
The appliance becomes very hot. Never
touch the interior surfaces of the cooking
compartment or the heating elements.
Always allow the appliance to cool down.
Keep children at a safe distance.
Risk of burns!
■
Accessories and ovenware become very
hot. Always use oven gloves to remove
accessories or ovenware from the cooking
compartment.
Risk of burns!
■
Alcoholic vapours may catch fire in the hot
cooking compartment. Never prepare food
containing large quantities of drinks with a
high alcohol content. Only use small
quantities of drinks with a high alcohol
content. Open the appliance door with
care.
Risk of burns!
■
Hot steam may escape during operation.
Do not touch the ventilation openings.
Keep children away.
Risk of scalding!
■
The accessible parts become hot during
operation. Never touch the hot parts. Keep
children at a safe distance.
Risk of scalding!
■
Water in a hot cooking compartment may
create hot steam. Never pour water into
the hot cooking compartment.
Risk of scalding!
■
When you open the appliance door, hot
steam can escape. Steam may not be
visible, depending on its temperature.
When opening, do not stand too close to
the appliance. Open the appliance door
carefully. Keep children away.
Risk of scalding!
■
The water in the evaporator dish is still hot
even after the appliance has been
switched off. Do not empty the evaporator
dish immediately after switching off the
appliance. Allow the appliance to cool
down before cleaning it.
Risk of scalding!
4
■
Hot liquid may spill over the sides of
cooking containers when they are
removed from the cooking compartment.
Remove hot cooking containers with care
and always wear oven gloves.
Risk of injury!
■
Scratched glass in the appliance door
may develop into a crack. Do not use a
glass scraper, sharp or abrasive cleaning
aids or detergents.
Risk of injury and risk of fire!
■
Flammable liquids can catch fire in the
cooking compartment when it is hot
(explosion). Do not fill the water tank with
any flammable fluids (e.g. alcoholic
drinks). Only fill the water tank with water
or with the descaling solution that is
recommended by us.
Risk of electric shock!
■
Incorrect repairs are dangerous. Repairs
may only be carried out by one of our
trained after-sales engineers. If the
appliance is faulty, unplug the mains plug
or switch off the fuse in the fuse box.
Contact the after-sales service.
Risk of electric shock!
■
The cable insulation on electrical
appliances may melt when touching hot
parts of the appliance. Never bring
electrical appliance cables into contact
with hot parts of the appliance.
Risk of electric shock!
■
Penetrating moisture may cause an
electric shock. Do not use any highpressure cleaners or steam cleaners.
Risk of electric shock!
■
When replacing the cooking compartment
bulb, the bulb socket contacts are live.
Before replacing the bulb, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box.
Risk of electric shock!
■
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
Causes of damage
Caution!
■ Do not place anything on the cooking compartment floor. Do
not cover it with aluminium foil. A build-up of heat could
damage the appliance.
The cooking compartment floor and the evaporator dish must
always be kept clear. Always place ovenware in a perforated
cooking container or on a wire rack.
■ Aluminium foil in the cooking compartment must not come
into contact with the door panel. This could cause permanent
discolouration of the door panel.
■ Ovenware must be heat and steam resistant. Silicone baking
tins are not suitable for combined operation with steam.
■ Do not use ovenware that shows signs of rust. Even the
smallest spots of rust can lead to corrosion in the cooking
compartment.
■ When steaming with a perforated cooking container, always
insert the baking tray or the solid cooking container
underneath. Dripping liquid is caught.
■ Do not store moist food in the closed cooking compartment
for long periods. It can lead to corrosion in the cooking
compartment.
■ Fruit juice may leave stains in the cooking compartment.
Always remove fruit juice immediately and wipe the cooking
compartment with a moist and dry cloth.
■ If the door seal is very dirty, the appliance door will no longer
close properly during operation. The fronts of adjacent units
could be damaged. Always keep the door seal clean and
replace when necessary.
■ Do not place anything on the open appliance door. The
appliance could be damaged.
■ Do not carry or hold the appliance by the door handle. The
door handle cannot support the weight of the appliance, and
could break.
■ The cooking compartment in your appliance is made of high
grade stainless steel. Improper care can lead to corrosion in
the cooking compartment. Refer to the care and cleaning
instructions in the instruction manual. Remove food residues
from the cooking compartment as soon as the appliance has
cooled.
5
Your new appliance
(O
N7
7
In this section, you will find information on
■ the control panel
■ the operating modes
■ automatic calibration
Control panel
HFWURQLFFORF
H[WGLVSOD\
HPSHUDWXUHGLVSOD\
6WRSEXWWRQ6WDUWEXWWRQ
5RWDU\VHOHFWRU
&ORFNIXQFWLRQEXWWRQ
Control elementUse/meaning
Operating mode selectorSwitching the appliance on and off
Electronic clock
KJ
Temperature display (Basic settings)
±
Clock function buttonSelects the clock function (see section: Electronic clock)
Rotary selectorMakes settings within a clock function (see section: Electronic clock)
Info buttonPress briefly: calls up additional information, for example the current temperature
Temperature selectorSets the temperature
2SHUDWLQJPRGHVHOHFWRU
,QIREXWWRQ
7HPSHUDWXUHVHOHFWRU
Selects the desired operating mode
during the heating up phase
Press and hold: calls up the Basic settings menu (see section: Changing the Basic
settings)
Changes the settings in the Basic settings menu (see section: Changing the Basic
settings)
1DYLJDWLRQEXWWRQ
$XWRPDWLFSURJUDPPHV
3
0
0HPRU\
6WDUW
6WRS
Buttons
i
X
l
ƒ
„
Pop-out operating knob
The rotary, temperature and operating mode selectors can all
be popped out. Push the required operating knob to pop it in or
out.
6
Navigation buttonSwitches between the different lines of the text display. The settings are saved as
you do so. If the
options. Press the
Programme buttonSelects automatic programmes (see section: Steam)
Memory buttonSaves and accesses the settings (see section: Memory)
Start buttonStarts the operation
Stop buttonShort press: stops the operation (pause)
Press and hold: ends the operation
M symbol lights up in the text display, there are further selection
i navigation button to move to these.
Operating modes
Using the operating mode selector, you can select the following
operating modes:
Operating modeUse
Steam cooking35 - 100 °CFor vegetables, fish, side dishes, for juicing fruit and for blanching.
é
CircoSteam®120 - 230 °Cfor meat, bakes and baked goods.
8
Hot air30 - 230 °Cfor moist cakes, sponge, pot roasts.
3
Reheat100 - 180 °CFor plated meals and baked items.
ä
Dough proving35 - 50 °CFor yeast dough and sourdough.
ê
Defrost setting35 - 60 °CFor vegetables, meat, fish and fruit.
A
Low-temperature
/
cooking
Plate warming30 - 70 °Cfor porcelain tableware.
P
Keep warm60 - 100 °Cfor keeping food warm for up to two hours
ç
60 - 120 °Cfor sirloin, leg of lamb.
Hot air and steam are combined.
A fan in the back wall of the oven distributes the heat evenly inside the cooking
compartment.
Cooked food is gently reheated. The steam ensures that the food does not dry
out.
Dough will prove considerably more quickly than at room temperature. Hot air and
steam are combined so that the surface of the dough does not dry out
Hot air and steam are combined. The moisture gently transfers the heat to the
food. The food does not dry out or lose shape.
Tender pieces of meat stay particularly juicy.
Food does not cool down so quickly on preheated plates and dishes. Drinks also
remain warm for longer.
EasyClean®Makes cleaning the cooking compartment easier
>
DescalingFor descaling the water system and the evaporator dish
Í
Automatic calibration
The boiling temperature of water depends on the air pressure.
During calibration, the appliance is adapted to the pressure
conditions in the location where it is installed. This happens
automatically when you first use the appliance (see section:
First use). More steam develops than usual.
It is important that the appliance steams without interruption for
20 minutes at 100 °C. Do not open the appliance door during
this time.
If the appliance was not able to calibrate itself automatically (for
example, because the appliance door was opened), the
calibration process is carried out again during the next cooking
operation.
After moving house
So that the appliance automatically adjusts itself to its new
location, you must reset the appliance to the factory settings
(see section: Basic settings) and repeat the initial start-up
process (see section: First use).
After a power cut
The appliance saves the calibration settings even in the event
of a power cut or disconnection from the mains. Recalibration
is not necessary.
7
Your accessories
*
DWH
The accessories supplied with your appliance are suitable for
making many dishes. Ensure that you always insert the
accessories into the cooking compartment the right way round.
Accessories
The following accessories are supplied with your appliance:
Wire rack
For ovenware, cakes and ovenproof
dishes, and for roasting
Cooking container, perforated,
GN
Y, 40 mm deep
For steaming vegetables, juicing
berries and defrosting
Cooking container, solid, GN
40 mm deep
For cooking rice, pulses and
cereals
Cooking container, perforated,
GN
Z, 40 mm deep
for the steaming of whole fish or
large quantities of vegetables, for
juicing berries, etc.
Cooking container, solid, GN
28 mm deep (baking tray)
For baking tray bakes and for
catching dripping liquid during
steaming
Grease filter
protects the fan of the back panel
of the cooking compartment from
becoming dirty (e.g. from
spattering)
You can buy accessories from the after-sales service, from
specialist retailers or online.
Note: The cooking containers may warp during and after
cooking. This is caused by the considerable temperature
differences acting on the accessories. It may occur if only a
part of the accessory is occupied with food or if you place
frozen items, such as pizza, on the accessory. Once
accessories cool down again, they regain their original shape.
This does not affect their function.
Y,
Z,
Inserting accessories
The accessories are equipped with a locking function. The
locking function prevents the accessories from tilting when they
are pulled out. The accessories must be inserted into the
cooking compartment correctly for the tilt protection to work
properly.
When inserting the wire rack, check
■ that the lug (a) is pointing downwards
■ that the safety lug on the wire rack is at the back and facing
upwards.
D
D
When inserting the cooking container, ensure that the lug (a) is
facing downwards.
D
D
Cooking compartment
The cooking compartment has four shelf positions. The shelf
positions are counted from the bottom up.
UHDVHILOWHU
5DLOVIRUWKH
DFFHVVRULHV
Caution!
■ Do not place anything on the cooking compartment floor. Do
not cover it with aluminium foil. A build-up of heat could
damage the appliance.
The cooking compartment floor and the evaporator dish must
always be kept clear. Always place ovenware in a perforated
cooking container or on a wire rack.
■ Do not slide any accessories between the shelf positions, or
they may tip.
(YDSRUDWRUGLVK
:DWHUWDQNUHFHVV
ZLWKZ
UWDQN
Optional accessories
You can obtain further accessories from specialist retailers:
AccessoriesOrder no.
Z
Y
Z1683X3
Z1682X3
Z1673X3
Z1663X0
Z1662X0
Z1685X0
Z1665X0
Cooking container, solid, GN
deep
Cooking container, perforated, GN
40 mm deep
Cooking container, solid, GN
deep (baking tray)
Cooking container, solid, GN
deep
Cooking container, perforated, GN
40 mm deep
Porcelain cooking container, solid, GN
Porcelain cooking container, solid, GN
Wire rackZ1664X3
Roasting setZ1684X3
Grease filterZ1610X0
Cleaning sponge623 653
Z, 40 mm
Z,
Z, 28 mm
Y, 40 mm
Y,
8
AccessoriesOrder no.
Descaler311 138
Honeycomb microfibre cloth460 770
Before using the appliance for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
■ Setting the clock and language
■ Setting the water hardness range
■ Starting the appliance for the first time
■ Cleaning the accessories before use
■ Fitting the grease filter
Setting the language
Once the appliance has been connected to the power supply,
you must set the language for the text display.
1. Turn the temperature selector until the language you require
appears on the text display.
2. Press and hold the ± info button for 3 seconds.
Your setting is saved.
6SUDFKHZlKOHQ
'HXWVFK
Changing the language
Your appliance must be switched on.
1. If required, turn the operating mode selector to the Û position.
2. Press and hold the ± info button for 3 seconds.
This takes you directly to the language selection screen.
3. Turn the temperature selector until the language you require
appears on the text display.
4. Press and hold the ± info button for 3 seconds.
Your setting is saved.
Setting the clock
Note: When you press the KJ clock function button, you have
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
‹:‹‹ flashes in the clock display.
1. Briefly press the KJ clock function button to go to the
setting mode.
KJ and 3 symbols light up. ‚ƒ:‹‹ appears in the
The
clock display.
2. Set the current time using the rotary selector.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the
button repeatedly until the
KJ and 3 symbols light up again.
Change the time with the rotary selector.
KJclock function
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness "medium" (
Change the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
Notes
■ If your water is very hard, we recommend that you use
softened water.
■ If you use only softened water, you can set your appliance to
the "softened" water hardness range.
■ If you use mineral water, set the water hardness to hard.
■ If you use mineral water, you must only use non-carbonated
mineral water (see section "Filling and emptying the water
tank").
You can change the water hardness range in the basic settings
when the appliance is switched on.
1. If required, turn the operating mode selector to the Û position.
2. Press and hold the ± info button until "Select language"
appears in the text display.
3. Briefly press the ± information button repeatedly until ™‡ƒ
appears in the temperature display (water
hardness "medium").
4. Use the temperature selector to set the water hardness.
Water hardnessSetting symbol (temperature dis-
softened
soft
medium
hard
very hard
5. Press and hold the ± info button for 3 seconds.
Your setting is saved.
™‡ƒ) is the default setting.
play)
™‡‹
™‡‚
™‡ƒ
™‡„
™‡…
9
First use
Before first use, heat the empty appliance with é Steam
cooking for 20 minutes at 100 °C. Do not open the appliance
door during this time. The appliance is automatically calibrated
(see section: Automatic calibration).
1. Press the operating mode selector so that it pops out.
The appliance switches on.
2. Fill and insert the water tank (see section: Filling the water
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
3. Turn the operating mode selector round to é Steam
cooking.
4. Press the Start button.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
5. Press theKJ clock function button to exit the clock function.
6. Turn the operating mode selector back to the Û position and
click in place to turn off the appliance.
Leave the appliance door ajar until the appliance has cooled
down.
Fitting the grease filter in place
Hook the enclosed grease filter onto the hot air grille in the
back wall of the cooking compartment.
Leave the grease filter in the cooking compartment for all
applications.
: Risk of injury!
You could hurt yourself on the grease filter hooks. Always clean
the grease filter with care. Always place the grease filter in the
dishwater so that the hooks for fixing it in place are facing
downwards.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
Operating the appliance
In this section, you can read about
■ how to fill the water tank
■ how to switch the appliance on and off
■ what to note after each cooking operation
Filling the water tank
When you open the appliance door, you will see the water tank
on the right-hand side.
Caution!
Use of unsuitable liquids may damage the appliance
■ Only use fresh tap water, softened water or uncarbonated
mineral water.
■ If your tap water is very hard, we recommend that you use
softened water.
■ Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
You can obtain information about your tap water from your
water supplier. The water hardness can be checked with the
test strips enclosed.
Fill the water tank before each use:
1. Open the appliance door and take out the water tank (fig. A).
2. Fill the water tank with cold water up to the “max” mark (fig.
B).
Clean the grease filter with hot soapy water or in the
dishwasher every time heavy dirt deposits have been left
behind after cooking.
$
3. Close the tank cover until you feel it engage.
4. Slide in the water tank all the way (fig. C).
&
The tank must be flush with the water tank recess (fig. D).
%
PD[
'
10
Switching on the appliance
: Risk of scalding!
When you open the appliance door and remove the cooking
containers, hot liquids may squirt out because the cooking
containers may have warped. When opening, do not stand too
close to the appliance. Open the appliance door carefully.
Remove the cooking container carefully. Keep children at a
safe distance.
Note: Always use the cooking container and wire rack in their
standard position (not the other way up).
1. Press the operating mode selector to make it pop out.
The appliance switches on. "Appliance is ready for use"
appears in the text display.
2. Turn the operating mode selector until the desired operating
mode appears on the text display.
A default temperature appears on the temperature display.
6WHDPFRRNLQJ
water tank to the "max" mark, slide it back in and start the
appliance.
Heating indicator
The heating indicator displays the rising temperature in the
cooking compartment.
■ Temperature reached (fig. A)
■ Appliance reheating (fig. B)
$%
Current temperature
Press the
The current temperature is displayed for 3 seconds.
Displaying and changing the cooking time.
Press the
and
Turn the rotary selector to change the cooking time. The
change is saved automatically.
Changing the temperature
You can change the temperature at any time. To change the
temperature, turn the temperature selector until the required
temperature is displayed.
± info button.
KJ clock function button repeatedly until the KJ
x symbols light up. The current cooking time is displayed.
3. Turn the temperature selector to change the default
temperature.
Operating modeTemperature range Default cooking
Steam35 - 100 °C20 minutes
CircoSteam®120 - 230 °C30 minutes
Hot air30 - 230 °C-
Reheat100 - 180 °C10 minutes
Prove35 - 50 °C30 minutes
Defrost35 - 60 °C30 minutes
Slow cook60 - 120 °C-
Plate warming30 - 70 °C-
Keep warm60 - 100 °C-
For operating modes that use steam, a default cooking time
appears in the electronic clock. The
time) symbols light up.
4. Turn the rotary selector to change the default cooking time.
The new cooking time is saved automatically after 3 seconds.
You can also set the cooking time for operating modes that
do not use steam (see section: Electronic clock).
5. Press the Start button.
If you do not press the Start button, a signal sounds and
"Press Start button" appears in the text display.
When using
until the heating-up time has elapsed.
"Fill water tank?" message
This message appears if you set an operating mode and the
water tank is only half full.
If you think that the water in the water tank is sufficient for the
cooking procedure, you can start the appliance. If not, fill the
é Steam cooking, the cooking time does not start
time
KJ and x (cooking
Pause
Briefly press the Stop button to interrupt cooking (pause). The
cooling fan may continue running. Press the Start button to
restart.
If you open the appliance door during cooking, operation is
interrupted. Close the appliance door and press the Start
button to restart.
If you have switched on the Auto start, there is no need to
restart the appliance (see section: Basic settings).
"Fill water tank" message
If the water tank is empty, a signal sounds. “Fill water tank”
appears on the display. Cooking is interrupted.
1. Open the appliance door carefully.
N.B.: Hot steam will escape.
2. Remove the water tank, fill up to the "max" mark and slide the
tank back in.
3. Press the Start button.
Switching off the appliance
: Risk of scalding!
Hot steam may escape when the appliance door is opened.
Open the appliance door carefully during or after cooking.
When opening the door, do not lean over it. Ensure that,
depending on the temperature, steam is not visible.
Press and hold the Stop button to stop the cooking operation.
If you have set a cooking time, cooking is ended automatically.
A signal sounds. Press the
the signal.
The cooling fan may continue to run when you open the
appliance door.
Turn the operating mode selector back to the
push it in to turn off the appliance.
You can see in the temperature display whether there is high or
low residual heat in the cooking compartment.
Temperature displayText display
•
œ
KJ clock function button to stop
Û position and
Residual heat high
Residual heat low
11
After each use
Emptying the water tank.
1. Open the appliance door carefully.
Hot steam will escape.
2. Remove and clean the water tank.
3. Thoroughly dry the seal in the tank cover and the tank recess
in the appliance.
Caution!
Do not dry the water tank in the hot cooking compartment. This
will damage the water tank.
Electronic clock
Drying the cooking compartment
: Risk of scalding!
The water in the evaporator dish may still be hot. Allow it to cool
before wiping.
1. Leave the appliance door ajar until the appliance has cooled
down.
2. Once it has cooled down, wipe out the cooking compartment
and the evaporator dish with the enclosed cleaning sponge
and dry well with a soft cloth.
3. Remove food residues from the cooking compartment as
soon as the appliance has cooled. Burnt-on remains will be
much harder to remove later.
4. Wipe kitchen units or handles if condensation has formed on
them.
In this section, you can read about
■ how to set the timer
■ how to switch your appliance off automatically (cooking time
and end of operation)
■ how to switch your appliance on and off automatically (preset
operation)
■ how to set the time
Clock functionUse
Minute minderYou can use the minute minder as an egg timer or a kitchen timer. The appliance does
Q
Cooking timeThe appliances switches off automatically after a cooking time setting has elapsed
x
End of operation
y
Preset operationThe appliance switches on and off automatically. Cooking time and end of operation
ClockSetting the clock
3
not switch on or off automatically
‚:„‹ hours)
(e.g.
The appliance switches off automatically at a set time (e.g.
have been combined.
Clock display
&ORFNIXQFWLRQEXWWRQ5RWDU\VHOHFWRU
‚ƒ:„‹ o'clock)
Notes
■ Between the times ƒƒ:‹‹ and †:†Š the clock display is
dimmed if you do not make any settings in that period or no
clock function is activated.
■ When you set a clock function, the time interval increases
when you set higher values (e.g. cooking time up to
the minute, using
to the nearest 5 minutes).
■ For the Q minute minder, x cooking time, y end of
operation and preselection mode clock functions, a signal
sounds when the settings have elapsed and the
symbol flashes. To cancel the audible signal before it ends,
press the
■ Briefly press the KJ clock function button to select a clock
function. You then have 3 seconds to set the selected clock
function. After this time, the setting mode is exited
automatically.
12
KJ clock function button.
‚:‹‹œ
‚:‹‹œ to
Q or y
Switching the clock display on and off
1. Press and hold the KJclock function button for 6 seconds.
The clock display switches off. If a clock function is active,
the associated symbol remains lit.
2. Press the KJclock function button briefly.
The clock display switches on.
Timer
1. Press the KJclock function button repeatedly until the KJ
and
Q symbols light up.
2. Set the duration using the rotary selector (e.g. †:‹‹ minutes).
The setting is applied automatically. Then the clock is
displayed again and the minute minder starts counting down.
Cooking time
Automatic switch-off after a cooking time setting has elapsed.
1. Set the operating mode and temperature.
2. Press the KJ clock function button repeatedly until the KJ
and
x symbols light up.
3. Set the cooking time with the rotary selector
(e.g.
‚:„‹ hours).
4. Press the Start button.
é steam cooking, the cooking time does not start until
When
the heating up time has elapsed.
The appliance switches off automatically at the time set for the
end of operation.
1. Turn the operating mode selector back to the Û position.
2. Press the KJ clock function button to exit the clock function.
Preset operation
The appliance switches on automatically, then switches off
automatically at the time preselected for the end of operation.
Bear in mind that food that spoils easily must not stay in the
cooking compartment for too long.
Preselection mode is not possible with some of the automatic
programmes.
When é Steam cooking, the cooking time does not start until
the heating up time has elapsed. The end of operation which
was set is therefore delayed by the length of time required for
heating-up.
1. Set the operating mode and temperature.
2. Press the clock function button repeatedly until the KJ and
x symbols light up.
3. Set the cooking time with the rotary selector
(e.g.
‚:„‹ hours).
4. Press the clock function button repeatedly until the KJ
and
y symbols light up.
5. Set the end of operation using the rotary selector
(e.g.
‚ƒ:„‹).
6. Press the Start button.
The appliance waits until the appropriate time to switch on (in
the example at
The appliance switches off automatically at the time set for the
end of operation (
flashes.
1. Turn the operating mode selector back to the Û position.
2. Press the clock function button to end the preselection mode.
‚‚:‹‹).
‚ƒ:„‹). A signal sounds and the y symbol
Once the cooking time has elapsed, the appliance switches off
automatically.
1. Turn the operating mode selector back to the Û position.
2. Press the KJ clock function button to exit the clock function.
End of operation
Automatic switch-off at a set time. This function is only possible
for operating modes that do not use steam.
1. Set the operating mode and temperature. Press the Start
button.
The appliance heats up.
2. Press the KJ clock function button repeatedly until the KJ
and
y symbols light up.
3. Set the end of operation using the rotary selector
(e.g.
‚ƒ:„‹ o'clock).
The setting is applied automatically. The clock is then
displayed again.
Setting the clock
You can only change the clock when no other clock function is
active.
1. Press the KJ clock function button repeatedly until
the
KJand 3 symbols light up.
2. Set the clock using the rotary selector.
The setting is applied automatically.
Checking, correcting or deleting settings
1. To check your settings, press the KJ clock function button
repeatedly until the corresponding symbol lights up.
2. If necessary, you can correct your setting using the rotary
selector.
3. If you wish to cancel your setting, turn the rotary selector anti-
clockwise to the original value.
13
Automatic programmes
The automatic programmes enable you to prepare food very
easily. There are 16 programme groups containing a total of
70 programmes.
In this section, you will find out
■ how to set one of the automatic programmes
■ hints and tips on the programmes
■ Which programmes you can set (programme tables)
Setting a programme
Select the correct programme from the programme tables.
Follow the instructions for the programmes.
Example in the picture: You want to steam 500 g fresh chicken
breast.
■ "Poultry" programme group
■ Programme "Chicken breast, fresh, steamed"
Selecting a programme group
1. Press on the operating mode selector to turn on the
appliance.
2. Press the X button.
The first programme group is shown on the text display.
3. Turn the operating mode selector until the desired
programme group appears.
9HJHWDEOHV
3
Enter the weight
A default weight appears on the temperature display.
8. Turn the temperature selector to set the weight of the items to
be cooked.
Press the
± info button to request information on the
accessories. The information is displayed for a few seconds.
6WDUW
3RXOWU\
&KLFNHQEUHDVWIUHVKVWHDPHG
9. Press the Start button to start the programme.
03
No heating indicator appears.
Checking the cooking time
Press the
and
KJ clock function button repeatedly until the KJ
x symbols light up.
Programme with preselected mode
For some programmes, you can set a
y Preselection mode.
The programme will be started later and finish at the desired
time (see Section: Electronic clock).
Cancelling the programme
Press and hold the Start button to cancel the programme.
End of the programme
A signal sounds. Cooking has finished. To turn off the
appliance, press in the operating mode selector so that it clicks
into place.
Selecting the programme
4. Press the ì button.
The first programme in the programme group is shown on
the text display.
5. Turn the operating mode selector until the desired
programme is displayed.
&KLFNHQEUHDVWIUHVKVWHDPHG
3RXOWU\
3
Adjusting the cooking result individually
6. Press the ì button.
Individual adjustment is highlighted “-
7. Turn the operating mode selector to adjust the cooking result:
■ anti-clockwise: cooking results are set less intensively
■ clockwise: cooking results are set more intensively
ЩЩЩШЩЩЩ +”.
You can also modify the cooking result permanently for all
programmes at the same time (see Section: Basic settings).
: Risk of scalding!
Hot steam may escape when the appliance door is opened.
Open the appliance door carefully during or after cooking.
When opening the door, do not lean over it. Ensure that,
depending on the temperature, steam is not visible.
Notes about the programmes
All programmes are designed for cooking on one level.
The cooking result can vary according to the size and quality of
the food.
Ovenware
Use the suggested ovenware. All meals have been tested using
this ovenware. The cooking result may change if you use
different ovenware.
When cooking in the perforated cooking container, always
insert the baking tray at level 1. Dripping liquid is caught.
Amount/weight
Do not fill the food more than 4 cm deep in the accessories.
The automatic programmes require the weight of the food. With
individual pieces, always enter the weight of the largest. The
total weight must be within the specified weight range.
Cooking time
After the programme is started the cooking time is displayed. It
may change during the first 10 minutes, as the heating-up time
depends, among other things, on the temperature of the food
and the water.
14
Programme tables
Follow the instructions for the programmes.
Vegetables
Do not season vegetables until after cooking.
ProgrammeNotesAccessoriesLevel
Steam cauliflower/In florets*florets of equal sizePerforated cooking container
+
Baking tray
Steam broccoli florets*florets of equal sizePerforated cooking container
+
Baking tray
Steam green beans*-Perforated cooking container
+
Baking tray
Steam sliced carrots*slices, approx. 3 mm thickPerforated cooking container
+
Baking tray
Steam sliced kohlrabi*slices, approx. 3 mm thickPerforated cooking container
* You can set a preselection mode for this programme
Cereal products
Weigh the food and add the correct ratio of water:
■ Rice 1:1.5
■ Couscous 1:1
■ Millet 1:3
■ Lentils 1:2
Stir cereal products after cooking. The remaining water is then
quickly absorbed.
Making risotto
Add water to the risotto in the ratio of 1:2. Enter the total weight
including water. The message “Stir” appears after approx.
15 minutes. Stir the risotto and, if required, press the Start
button.
other. Enter the weight of the heaviest fish and choose pieces
as similar in size as possible.
+
Baking tray
+
Baking tray
+
Baking tray
+
Baking tray
paper
paper
3
1
3
1
3
1
3
1
2
2
Pastries, dessert
Baking plaited loaf
Leave the yeast dough to prove in the combination steam oven
for half an hour at 40 °C.
Making fruit compote
The programme is only suitable for fruits with stones and pips.
Weigh the fruit and add approximately
then add sugar and spices to taste.
Preparing rice pudding
Weigh the rice and add 2.5 times the amount of milk. Ensure
the level of rice and milk in the accessory is no higher than
ProgrammeNotesAccessoriesLevel
Plaited loaf0.6 - 1.8 kgBaking tray + greaseproof
Sponge cake0.8 - 2 kggreased springform cake tin
Fruit compote*-Baking tray2
Rice pudding-Baking tray2
Yoghurt in glass jars-Glass jars + perforated cooking
* You can set a preselection mode for this programme
Bread, bread rolls
Baking bread
The programmes are designed for baking loaves of bread
without a tin. The dough should not be too soft. Cut into the
dough several times with a sharp knife to a depth of approx.
1 cm before baking.
Y the amount of water,
2.5 cm. Stir after cooking. The remaining milk is quickly
absorbed.
Making yoghurt
Heat the milk to 90 °C on the hob. Then leave to cool to 40 °C.
If you are using UHT milk, you do not need to heat it.
Stir in one to two teaspoons of natural yoghurt per 100 ml milk,
or the corresponding amount of yoghurt culture into the milk.
Pour the mixture into clean jars and seal them.
After preparation, leave the glasses to cool in the refrigerator.
2
paper
2
with fluted ring base, dia. 26 cm
+ wire rack
2
container
Proving and baking bread dough
The message “Score bread” appears after approx. 20 minutes.
Score the dough and press the start button as required.
Bake fresh bread rolls
The rolls should all be the same weight. Enter the weight of an
individual bread roll.
* You can set a preselection mode for this programme
2
2
2
2
2
2
Defrosting
When freezing, lay the food as flat as possible and in portionsized pieces at -18 °C. Do not freeze excessively large
quantities. Once defrosted, food will not keep for as long and
spoils more quickly than fresh food.
Leave the food to defrost in the freezer bag, on a plate or in the
perforated cooking container. Always insert the baking tray
underneath. The food is then not left lying in the defrost water
and the cooking compartment remains clean.
All defrost programmes apply to raw food.
If necessary, the meal can occasionally be split apart or pieces
which have already defrosted can be removed from the
appliance.
After defrosting, allow the food to stand for a further 5 15 minutes to allow the temperatures to even out.
: Health risk!
When defrosting food from animal sources, you must remove
the liquid that escapes during defrosting. It must never come
ProgrammeNoteAccessoriesLevel
Fish/whole fishmax. 3 cm thickPerforated cooking container
Fish/Fish filletmax. 2.5 cm thickPerforated cooking container
Meatmax. weight per piece 1.5 kgPerforated cooking container
Berries-Perforated cooking container
into contact with other food. Bacteria could be transferred.
After defrosting, operate the combination steam oven for
15 minutes using Hot air at 180 °C.
Defrosting fish fillet
Do not place the fish fillets on top of each other.
Defrosting whole poultry
Remove the packaging before defrosting. Leave the poultry to
stand after defrosting. With large poultry (e.g. small turkeys),
you can remove the giblets after approximately 30 minutes
standing time.
Defrost meat
With this programme you can defrost individual joints of meat.
Only thaw fruit (not defrost)
If you only wish to thaw the fruit slightly, you can make an
individual adjustment to the cooking result.
+
Baking tray
+
Baking tray
+
Baking tray
+
Baking tray
+
Baking tray
3
1
3
1
3
1
3
1
3
1
18
Special
Sterilising bottles
Always clean the bottles with a bottle brush immediately after
drinking. Then clean them in the dishwasher.
Place the bottles in the perforated cooking container so that
they do not touch one another.
Dry the bottles with a clean cloth after sterilising. The process
corresponds to normal sterilisation by boiling.
Preserve
This programme is suitable for fruits with a stone and core and
for vegetables (except beans).
Blanch pumpkin before preserving.
ProgrammeNotesAccessoriesLevel
Sterilise bottles*-Perforated cooking container 2
Preservein 1-litre jarsPerforated container +
Eggs/Hard-boiled eggs*Eggs, size M, Max. 1.8 kgPerforated container +
Eggs/Soft-boiled eggs*Eggs, size M, max. 1 kgPerforated container +
* You can set a preselection mode for this programme
The programme is designed for 1 litre jars. For larger or smaller
jars, you must adjust the cooking result individually.
After the end of the programme, open the appliance door to
prevent cooking from continuing. Leave the jars to cool down
for a few minutes in the cooking compartment.
The programme is designed for firm fruit. If the fruit being used
is no longer firm, adjust the cooking results individually.
Cooking eggs
Pierce the eggs before cooking. Do not place eggs on top of
each other. Size M corresponds to a unit weight of approx.
50 g.
Baking tray
Baking tray
Baking tray
3
1
3
1
3
1
Memory
You can use the Memory function to save up to 6 of your own
settings and recall them for use at any time. The Memory
function is particularly useful for dishes that you make on a
regular basis. You can also store one of the automatic
programmes.
Saving to the Memory function
1. Select the operating mode, temperature and cooking time or
one of the automatic programmes
(Do not press the Start button).
2. Press the l button to call up the menu memory.
3. Turn the operating mode selector to choose one of the 6
memory spaces.
4. Press and hold l button until a signal sounds.
"Memory saved" is shown in the text display.
Cancelling the memory function
Press the
saving.
Starting the memory function
1. Turn the operating mode selector to the Û position.
2. Place the meal in the cooking compartment.
3. Press the l button to call up the menu memory.
4. Turn the operating mode selector to select the memory
location.
5. Press the Start button.
After starting, you can change the temperature and cooking
time (not with any of the automatic programmes).
If you select the
start until the heating up time has elapsed.
Stopping (pausing) memory
Briefly press the Stop button. The Start button flashes. The
cooling fan may continue running. Press the Start button to
restart.
Cancelling the memory function
Press and hold the Stop button.
l button briefly to exit the Memory menu without
é Steam cooking, the cooking time does not
Deleting a memory setting
You can delete or replace a memory setting.
1. Turn the operating mode selector to the Û position.
2. Press the l button to call up the menu memory.
3. Turn the operating mode selector to select the memory
location.
4. Press the ì button.
“Delete? No“ appears in the text display.
5. Use the operating mode selector to switch to “Delete? Yes“.
6. Press the ì button to delete the memory setting.
7. Press the l button briefly to exit the Memory menu.
19
Childproof lock
In this section, you can read about
■ how to lock your appliance
■ how to lock your appliance permanently
Lock
Once it has been locked, the appliance cannot be switched on
accidentally or by unauthorised users (e.g. by children playing).
To switch the appliance on again, you must unlock it. After
appliance operation, the appliance is not automatically locked.
Lock it again if necessary or activate the permanent lock.
Lock appliance
1. Switch off the appliance.
2. Press and hold the ± info button for 3 seconds to go to the
basic settings menu.
3. Press the ± info button briefly and repeatedly until ™‚‹
appears in the temperature display.
4. Turn the temperature selector until ™‚‚ appears on the
temperature display.
5. Press and hold the ± info button until the ‚ symbol appears
in the temperature display.
Note: If you try to switch on the locked appliance, on the temperature display and “controls locked” appears on
the text display.
Unlocking the appliance
1. Press and hold the ± info button until ™‚‚ appears in the
temperature display.
2. Turn the temperature selector until ™‚‹ appears on the
temperature display.
3. Press and hold the ± info button until the ‚ symbol goes
out.
†- appears
Permanent lock
Once it has been permanently locked, the appliance cannot be
switched on accidentally or by unauthorised users (e.g. by
children playing).
To switch the appliance on, you must interrupt the permanent
lock briefly. After you have switched your appliance off, it locks
again automatically.
Locking the appliance permanently
1. Switch off the appliance.
2. Press and hold the ± info button for 3 seconds to go to the
basic settings menu.
3. Press the ± info button briefly and repeatedly until ™‚‹
appears in the temperature display.
4. Turn the temperature selector until ™ƒ‚ appears on the
temperature display.
5. Press and hold the ± info button for 3 seconds.
Your appliance will be locked after 30 seconds. The
symbol appears in the temperature display
Note: If you try to switch on the locked appliance, on the temperature display and “Appliance permanent lock”
appears on the text display.
Interrupting permanent lock
1. Press and hold the ± info button until ™ƒ‚ appears in the
temperature display.
2. Turn the temperature selector until ™ƒ‹ appears on the
temperature display.
3. Press and hold the ± info button until the ‚ symbol goes
out.
The permanent lock is interrupted.
4. Switch the appliance on within 30 seconds.
After the permanent lock is switched off, it is reactivated after
30 seconds.
Unlocking the appliance permanently
1. Press and hold the ± info button until ™ƒ‚ appears in the
temperature display.
2. Turn the temperature selector until ™ƒ‹ appears on the
temperature display.
3. Press and hold the ± info button until the ‚ symbol goes
out.
4. Within 30 seconds, press and hold the ± info button again for
3 seconds to go to the basic settings menu.
5. Press the ± info button briefly and repeatedly until ™ƒ‚
appears in the temperature display.
6. Turn the temperature selector until ™‚‹ appears on the
temperature display.
7. Press and hold the ± info button for 3 seconds.
The appliance is permanently unlocked.
‚
†˜ appears
Basic settings
Your appliance has various basic settings, which are preset at
the factory. You can change the basic settings as you require.
If you want to cancel all the changes, you can restore the
factory settings.
20
You can only change the basic settings if the appliance is
switched on.
1. If required, turn the operating mode selector to the Û position.
2. Press and hold the ± info button until "Select language“
appears in the text display.
3. Press the ± button repeatedly until the desired basic setting is
displayed (e.g. “Audible signal off“).
4. Use the temperature selector to change the basic setting
(e.g. to “Audible signal duration 2 minutes“).
5. Press and hold the ± info button for 3 seconds.
The change is saved.
You can change the following basic settings:
Basic settings menu
Sub menuBasic settingSetting
Select languageAdditional languages are
Childproof lockLock is not activated
Audible signal
duration
Auto startoff
Adjust individually
* Restore the appliance to the factory settings:
■ all changes to the basic settings are deleted
■ Memory is cleared
■ automatic calibration is carried out again
possible.
Lock is activated
Permanent lock is activated
Audible signal off
Audible signal duration
30 seconds
Audible signal duration
2 minutes
Audible signal duration
10 minutes
on
-
ЩЩЩШЩЩЩ +™†...
symbol
™‚‹
™‚‚
™ƒ‚
™„‹
™„‚
™„ƒ
™„„
™…‹
™…‚
Basic settings menu
Sub menuBasic settingSetting
Water hardness
range
Steam heating up
signal
Factory settings*Do not restore
* Restore the appliance to the factory settings:
■ all changes to the basic settings are deleted
■ Memory is cleared
■ automatic calibration is carried out again
softened
1-soft
2-medium
3-hard
4very hard
off
on
Restore
symbol
™‡‹
™‡‚
™‡ƒ
™‡„
™‡…
™ˆ‹
™ˆ‚
™‰‹
™‰‚
Automatic safety cut-out
The automatic safety cut-out is only activated if you have not
made any settings on your appliance for a prolonged period.
The length of time after which your appliance switches itself off
depends on the settings that you make.
Care and cleaning
In this section, you will find information on
■ Care and cleaning of your appliance
■ Oven cleaning aid EasyClean®
■ Descaling
: Risk of short circuit!
Do not use high-pressure cleaners or steam jet cleaners to
clean your appliance.
Caution!
Risk of surface damage: Do not use
■ harsh or abrasive cleaning agents
■ oven cleaners
‹‹‹ flashes in the temperature display. Cooking is interrupted.
Turn the operating mode selector back to the
deactivate the automatic safety switch-off function. You can now
make new settings.
■ corrosive or aggressive cleaners, or those containing
chlorine
■ cleaning agents with a high alcohol content
If such an agent comes into contact with the front of the
appliance, wash it off immediately with water.
Caution!
Risk of surface damage: If descaler or the oven and grill
cleaning gel comes into contact with the front of the appliance
or other sensitive surfaces, wash it off immediately with water.
Remove food residues from the cooking compartment as soon
as the appliance has cooled. Burnt-on remains will be much
harder to remove later.
For heavy soiling use the cleaning aid (see section: Cleaning
aid EasyClean®).
Û position to
21
Salts are very corrosive and can cause rust. Remove remains
of acidic sauces (ketchup, mustard) or salted food from the
cooking compartment immediately after cooling.
Do not use hard scouring pads or cleaning sponges.
Cleaning agents
Appliance exterior (with aluminium front)Use soapy water and dry with a soft cloth.
Appliance exterior (with stainless steel
front)
Cooking compartment interior with evaporator dish
Grease filterRemove the grease filter on the back wall of the cooking compartment by lifting it off
Mild window cleaning agent - wipe the aluminium front horizontally and without applying pressure using a soft window cloth or a lint-free microfibre cloth.
Use soapy water and dry with a soft cloth.
Always remove flecks of limescale, grease, starch and albumin (e.g. egg white) immediately. Special stainless steel cleaning agents can be obtained from the after-sales
service or from specialist retailers.
Hot, soapy water or a vinegar solution use the enclosed cleaning sponge or a soft
washing-up brush.
Caution!
The cooking compartment could rust.: Do not use steel pads or scourers.
If the cooking compartment contains heavy deposits of dirt, use only the oven and grill
cleaning gel recommended by the after-sales service (ordering no. 463 582, also
available online in the eShop). Follow the manufacturer's instructions. Other oven
cleaners could damage the appliance.
The cooking compartment light and the seals around the door, light and evaporator
dish must not come into contact with the gel. Allow the gel to act for at least 12 hours
and do not switch on the appliance during this time. Then rinse out the cooking compartment thoroughly with water (e.g. with a spray bottle) to remove all gel residues.
upwards and clean it with hot soapy water or in the dishwasher. Clean the grease filter
every time heavy dirt deposits have been left behind after cooking
: Risk of injury!
You could hurt yourself on the grease filter hooks. Always clean the grease filter with
care. Always place the grease filter in the dishwater so that the hooks for fixing it in place
are facing downwards.
Water tankSoapy water - do not clean in the dishwasher.
Water tank recessRub dry after every use
Seal in the water tank lidThoroughly dry after every use
RailsSee section: Cleaning the rails
Door panelsSee section: Cleaning the door panels
Caution!
Surface damage: After cleaning, wipe the door panels with glass cleaner, then dry. Otherwise, stains will appear which it will not be possible to remove.
Door sealHot soapy water
AccessoriesSoak in hot soapy water. Clean with a washing-up brush or sponge or in the dish-
washer.
Clean stains caused by starchy food (e.g. rice) with a vinegar solution
Cleaning sponge
The enclosed cleaning sponge is very absorbent. Use the
cleaning sponge only for cleaning the cooking compartment
and for removing residual water from the evaporator dish.
Wash the cleaning sponge thoroughly before using for the first
time. You can wash the cleaning sponge in the washing
machine (hot wash).
Microfibre cloth
The honeycomb microfibre cloth is particularly suitable for
cleaning sensitive surfaces such as glass, glass ceramic,
stainless steel or aluminium (product no. 460 770, also
available from our online eShop). It removes liquid and greasy
deposits in one go.
Roasting set
If possible use the roasting set when roasting (ordering
no. Z1684X3, also available online in the eShop). This
considerably reduces the amount of spatter from the roast and
therefore the amount of soiling in the cooking compartment.
22
Oven cleaning aid
The cleaning aid loosens dirt in the cooking compartment using
steam. It can then be removed easily.
The cleaning process consists of:
■ Cleaning (approx. 30 minutes), then empty the evaporator
dish and wipe out the appliance
■ 1st rinse (20 seconds), then empty the evaporator dish
■ 2nd rinse (20 seconds), then remove the remaining water
All three steps must be completed in full. The appliance is
ready for operation again only after the 2nd rinse.
Preparation
Allow the cooking compartment to cool down and remove the
accessories. Clean the evaporator dish with the enclosed
cleaning sponge.
Put a drop of washing-up liquid into the evaporator dish on the
cooking compartment floor.
Starting the cleaning aid
1. Press the operating mode selector to make it pop out.
The appliance switches on.
2. Turn the operating mode selector to > EasyClean®.
3. Fill the water tank with water up to the "max" mark and slide it
in.
4. Press the Start button.
The cleaning aid starts running. The light in the cooking
compartment remains switched off.
“’† appears in the
temperature display.
Emptying the evaporator dish and wiping out the appliance
A signal sounds after approx. 30 minutes. "Wipe out appliance"
appears in the text display.
1. Open the appliance door.
2. Take the rails out of the cooking compartment and clean
them (see section: Cleaning the rails).
3. Wipe out all loosened food residues from the cooking
compartment and the evaporator dish using a soft washingup brush and the cleaning sponge.
4. If required, fill the water tank with water and reinsert it.
5. Close the appliance door.
1st rinse
Press the Start button.
The appliance starts rinsing. "1st rinse" appears in the display.
Empty evaporator dish
After 20 seconds, "Empty evaporator dish" appears in the text
display.
1. Open the appliance door.
2. Thoroughly rinse out the cleaning sponge.
3. Remove the remaining water from the evaporator dish using
the cleaning sponge.
4. Close the appliance door.
2nd rinse
Press the Start button.
The appliance starts rinsing. "2nd rinse" appears in the display.
Removing the remaining water
After 20 seconds, "End" and "Empty evaporator dish" appear in
the text display.
1. Open the appliance door.
2. Remove the remaining water from the evaporator dish using
the cleaning sponge.
3. Wipe out the cooking compartment using the cleaning
sponge and then dry with a soft cloth.
4. Turn the operating mode selector back to the Û position.
5. To turn off the appliance, press in the operating mode
selector so that it clicks into place.
The cleaning aid is complete.
Cancelling the cleaning aid
Note: After cancelling the cleaning aid, the appliance must be
rinsed twice. The appliance is locked against other applications
until the second rinsing operation is complete.
1. Press and hold the Stop button to cancel the Cleaning aid.
To ensure that no washing-up liquid remains in the appliance,
it must be rinsed twice after a cancellation.
2. Press the Start button.
"Wipe out appliance" appears in the display.
3. If required, fill the water tank with water, reinsert it and press
the Start button.
Now proceed as described in the section “Emptying the
evaporator dish and wiping out the appliance”.
Descaling
The appliance must be descaled at regular intervals in order for
it to continue operating correctly. "Descale the appliance"
reminds you of this.
You can only dispense with descaling completely if you
exclusively use softened water.
The descaling consists of:
■ Descale (approx. 30 minutes), then empty the evaporator
dish and refill the water tank
■ 1st rinse (20 seconds), then empty the evaporator dish
■ 2nd rinse (20 seconds), then remove the remaining water
All three steps must be completed in full. The appliance is
ready for operation again only after the 2nd rinse.
Descaler
Only use the liquid descaler recommended by the after-sales
service for descaling (product no. 311 138, also available
online from the eShop). Other descalers may damage the
appliance.
1. Prepare a descaling solution by mixing 300 ml water and
60 ml liquid descaler.
2. Empty the water tank and fill with descaling solution.
Caution!
Risk of surface damage: If descaler comes into contact with the
front of the appliance or any other sensitive surfaces, wash it off
immediately with water.
Starting descaling
The cooking compartment must have cooled down completely.
1. Press the operating mode selector to make it pop out.
The appliance switches on.
2. Turn the operating mode selector to Í Descale.
3. Slide in the water tank containing the descaling solution and
close the appliance door.
4. Press the Start button.
The descaling process starts. The light in the cooking
compartment remains switched off.
Emptying the evaporator dish and refilling the water tank
An audible signal sounds after approx. 30 minutes. "Empty
evaporator dish and refill water tank" appears in the text
display.
1. Open the appliance door.
2. Remove the descaling solution from the evaporator dish
using the cleaning sponge provided.
3. Rinse the water tank thoroughly, fill with water and reinsert.
"Appliance ready to rinse" and "1st rinse" appear in the text
display.
4. Close the appliance door.
1st rinse
Press the Start button.
The appliance starts rinsing. "1st rinse" appears in the display.
Empty evaporator dish
After 20 seconds, "Empty evaporator dish" appears in the text
display.
1. Open the appliance door.
2. Thoroughly rinse out the cleaning sponge.
23
3. Remove the remaining water from the evaporator dish using
the cleaning sponge.
4. Close the appliance door.
2nd rinse
Press the Start button.
The appliance starts rinsing. "2nd rinse" appears in the display.
Removing the remaining water
After 20 seconds, "End" and "Empty evaporator dish" appear in
the text display.
1. Open the appliance door.
2. Remove the remaining water from the evaporator dish using
the cleaning sponge.
3. Wipe out the cooking compartment using the cleaning
sponge and then dry with a soft cloth.
4. Turn the operating mode selector back to the Û position.
5. To turn off the appliance, press in the operating mode
selector so that it clicks into place.
Descaling is complete.
Cancelling the descaling
Note: After cancelling the descaling, you must rinse the
appliance twice. The appliance is locked against other
applications until the second rinsing operation is complete.
1. Press and hold the Stop button to cancel the descaling
process.
To ensure that no descaling solution remains in the
appliance, it must be rinsed twice after a cancellation.
2. Press the Start button.
"Empty evaporator dish and refill water tank" appears in the
text display.
Now proceed as described in the "Emptying the evaporator
dish and refilling the water tank" section.
Removing the appliance door
1. Open the appliance door fully.
2. Fold out the locking levers on the left and right fully (figure A).
The hinges are secured and cannot snap closed.
3. Close the appliance door until you feel some resistance.
4. With both hands, grip the door on the left and right-hand side,
close the door a little more and pull it out (Fig. B).
$
Fitting the appliance door
Refit the appliance door after cleaning.
1. Insert the hinges in the left and right-hand bracket (figure C).
The notch on both hinges must engage.
2. Open the appliance door fully.
3. Close the locking levers on the left and right-hand side fully
(figure D).
&
%
'
Descaling the evaporator dish only
You can also use "Descale" if you do not wish to descale the
whole appliance, but only the evaporator dish in the cooking
compartment.
The only difference is as follows:
1. Prepare a descaling solution by mixing 100 ml water and
20 ml liquid descaler.
2. Completely fill the evaporator dish with descaling solution.
3. Fill the water tank with water only.
4. Start "Descale" as described.
You can also descale the evaporator dish manually.
Removing and fitting the appliance door
You can remove the appliance door to clean it more
thoroughly.
: Risk of injury!
The hinges of the appliance door may snap shut with great
force. Always open the hinge locking lever fully when removing
the appliance door and close it fully after refitting. Do not reach
into the hinge.
: Risk of injury!
If the appliance door has only been unhinged on one side, do
not reach into the hinge. The hinge can snap back with great
force. Call the aftersales service.
The appliance door is secured and can no longer be
removed.
4. Close the appliance door.
Cleaning the door panels
To facilitate cleaning, you can remove the door panels from the
appliance door.
: Risk of injury!
The components inside the appliance door may have sharp
edges. Take care not to cut yourself. Wear protective gloves.
: Risk of injury!
The appliance must not be used again until the door panels
and appliance door have been correctly fitted.
Removing the door panel
1. Unhook the appliance door and lay it on a soft, clean surface
with the front side facing downwards (see section:Removing
and installing the appliance door).
24
2. Grip the door panel next to the hinges and pull it out of the
plug-in holders (not visible).
3. Lift the door panel slightly and remove it in the direction of the
hinges.
Removing the intermediate panel
Before removing, make a note of the position in which the
intermediate panel is fitted, so that you do not refit it the wrong
way round later.
1. Press the left and right-hand holders outwards.
2. Lift the intermediate panel slightly and take it out.
Cleaning
Clean the door panels with glass cleaner and a soft cloth.
Caution!
Do not use any sharp or abrasive medium or a glass scraper.
The glass could be damaged.
Cleaning the rails
The rails can be removed for cleaning.
: Risk of burning due to hot components in the cooking
compartment!
Wait until the cooking compartment has cooled down.
Detaching the rails
Note: Swing the front of the rail as far as possible (until you feel
resistance), because otherwise the appliance side panel may
become bent.
1. Carefully press the front of the rail upwards until it becomes
detached, and release it from the holder at the side (fig. A).
2. Detach the rail from the holder and remove it (fig. B).
$
3. Clean the rails with washing-up liquid and a sponge/brush
or
Clean the rails in the dishwasher.
Attaching the rail
1. Position the rail so that the indentations are facing upwards.
2. Hook the rail in at the back and push it towards the rear until
it engages (fig. C).
3. Hook the front of the rail onto the holder and press down until
it engages and is fixed level in place in the appliance once
more (fig. D).
%
Fitting the intermediate panel
1. Insert the intermediate panel on the left and right into the
supports.
2. Push the intermediate panel downwards in the retainers.
Fitting the door panel
1. Insert the door panel on the left and right into the supports.
2. Press the door panel downwards into the plug-in holders.
&
Each set of rails only fits on one side.
'
3. Refit the appliance door.
25
Troubleshooting
Malfunctions often have simple explanations. Please read the
following instructions before calling the after-sales service.
Repairs may only be carried out by fully trained after-sales
service technicians. Incorrect repairs to your appliance may
present considerable risks for the user.
ProblemPossible causeNotes/remedy
The appliance does not workThe plug is not plugged inConnect the appliance to the electricity
Power cutCheck whether other kitchen appliances
Circuit-breaker faultyCheck in the fuse box to make sure that
Faulty operationSwitch off the circuit-breaker for the appli-
The appliance cannot be startedThe appliance door is not fully closedClose the appliance door
The appliance is not switched offTurn the operating mode selector back to
The appliance cannot be started. "Descale" appears in the text display.
The appliance cannot be started. "Clean"
appears in the text display.
‹:‹‹ flashes in the clock display
‹:‹‹ flashes in the clock display, §§§
appears in the temperature display
The appliance is not in operation. A cooking time is shown on the display.
"Safety cut-out" appears in the text display
and
‹‹‹ flashes in the temperature dis-
play
‹‹‹ flashes in the temperature display
"Fill water tank" appears even though the
water tank is full
"Fill water tank" appears even though the
water tank is not yet empty, or the water
tank is empty but "Fill water tank" does not
appear
The water tank empties for no discernible
reason. The evaporator dish overflows
The evaporator dish has boiled empty
even though the water tank is full.
"Empty/Clean tank?" appears in the display
Descaling has been cancelledPress the Start button. Then rinse the
Cleaning aid was cancelledPress the Start button. Then rinse the
Power cutReset the clock (see section: Electronic
Power cut during cooking
The Start button was not pressed after the
setting had been made.
Automatic safety cut-out is activeTurn the operating mode selector back to
The appliance is not switched offTurn the operating mode selector back to
The water tank has not been inserted
properly
The detection system is not workingCall the after-sales service
The water tank is dirty. The moving water
level indicators are jammed
The water tank was not closed properlyClose the lid until you feel it lock into place
The tank lid seal is dirtyClean the seal
The tank lid seal is faultyObtain a new water tank from the after-
The water tank has not been inserted
properly
The feed line is blockedDescale the appliance. Check whether the
The appliance has not been used for at
least two days and the water tank is full
: Risk of electric shock!
■ Work on the appliance electronics may only be performed by
a specialist.
■ Always disconnect the appliance from the power supply
when work is carried out on the electronics. Switch off the
circuit breaker or remove the fuse from your household fuse
box.
supply
are working
the circuit-breaker for the appliance is OK
ance in the fuse box and switch it back on
after approx. 10 seconds
the
Û position and switch on again.
appliance twice (see section: Descaling).
Proceed as described in the section "Emptying the evaporator dish and refilling the
water tank".
appliance twice (see section: EasyClean®
cleaning aid. Proceed as described in the
section "Emptying the evaporator dish and
wiping out the appliance")
clock)
Press the KJ clock function button, reset
the clock (see section: Electronic clock)
Press the Start button or delete the setting
with the Stop button
the Û position and lock it in place
the
Û position and lock it in place
Push in the water tank until it locks into
place.
Shake and clean the water tank. If the
parts cannot be freed, obtain a new water
tank from the after-sales service
sales service
Push in the water tank until it locks into
place
water hardness range is set correctly
Empty and clean the water tank. Always
empty the water tank after cooking
26
ProblemPossible causeNotes/remedy
There is a "pop" noise during cookingCold/warm effect with frozen food, caused
When you cook with steam, a lot of steam
is created
When cooking with steam, a great deal of
steam is created again
Steam escapes from the ventilation slots
during cooking
The appliance is not producing steam
properly
Error message "E011" appears in the temperature display
An error message "E..." appears in the
temperature display
The appliance is no longer heating. The
colon is flashing in the clock display. For
example,
ture display
The appliance is unable to calibrate itself
automatically if cooking times are too
short
Limescale has formed in the applianceDescale the appliance (see section: Des-
A button was pressed for too long or is
jammed
Technical fault
A button combination was actuatedSwitch off the appliance, press and hold
This is normal
This is normal
Restore the appliance to the factory setting (see section: Basic settings). Then
start
é Steam cooking at 100 °C for
20 minutes
This is normal
caling).
Press the
delete the error message. Press all of the
buttons individually and check if they are
clean
Press the
delete the error message, and reset the
clock if necessary. If the error message
appears again, call the after-sales service
the
and hold the
4 seconds, then press and hold the
button for 3 seconds
KJ clock function button to
KJ clock function button to
± info button for 3 seconds, then press
KJ clock function button for
± info
Replacing the cooking compartment bulb
Heat-resistant 230 V/25 W halogen bulbs with seals are
available from the after-sales service. Please specify the E
number and FD number of your appliance.
: Risk of burns!
Allow the cooking compartment and cooking compartment light
to cool before changing the bulb.
Always use a dry cloth to remove a new halogen bulb from the
packaging, otherwise it will not last as long.
1. Switch off the fuse in the fuse box or unplug at the mains.
2. Turn the cover anti-clockwise to remove.
3. Remove the bulb and replace with a bulb of the same type.
4. Slide the new seals and the clamping ring onto the glass
cover in the right order.
Changing the door seal
If the seal around the outside of the cooking compartment is
faulty, it must be replaced. Replacement seals for your
appliance can be obtained from the after-sales service. Please
specify the E number and FD number of your appliance.
1. Open the appliance door.
2. Pull off the old seal.
3. Push in the new door seal at one point and pull it in all the
way round. The joint must be at the side.
4. Check again that the seal is correctly fitted in the corners.
5. Screw the glass cover with the seals back on again.
6. Connect the appliance to the mains and reset the clock.
Never operate the appliance without the glass cover and seals.
Replacing the glass cover or seals
Any damaged glass cover or seals must be replaced. Please
provide the after-sales service with the E number and FD
number of your appliance.
27
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
E number and FD number
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate bearing these numbers can
be found on the lower left-hand side when you open the
appliance door.
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
After-sales service
O
FD no.
Environmental protection
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with European
Directive 2012/19/EU concerning used electrical and
electronic appliances (waste electrical and electronic
equipment - WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Please note that there will be a fee for a visit by a service
technician in the event of a malfunction, even during the
warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
GB0844 8928989
Calls from a BT landline will be charged at up to
3 pence per minute. A call set-up fee of up to 6 pence
may apply.
IE01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Trust the expertise of the manufacturer, and rest assured that
the repair will be carried out by trained service technicians
using original spare parts for your domestic appliance.
Tips for saving energy
■ Only preheat the appliance if this is specified in the recipe or
in the operating instructions table.
■ Open the appliance door as infrequently as possible while
the food is cooking.
■ Use dark, black lacquered or enamelled baking tins for
baking. They absorb the heat particularly well.
■ It is best to bake several cakes one after the other. The
combination steam oven will still be hot. This reduces the
baking time for the second cake. You can also place two loaf
tins next to each other.
■ If the cooking time is relatively long, you can switch off the
combination steam oven 10 minutes before the end of the
cooking time and use the oven's residual heat to complete
the cooking process.
■ When steaming, you can cook on several levels at the same
time. When preparing foods with different cooking times,
those with the longest cooking time should be placed in the
oven first.
Tables and tips
The tables contain a selection of dishes which are particularly
suitable for your combination steam oven. You can find out
which operating mode, accessories and cooking time to select.
Unless otherwise stated, the information given applies to
inserting accessories when the appliance is cold.
Accessories
Use the accessories provided.
When steaming in the perforated cooking container, always
insert the baking tray underneath. Dripping liquid is caught.
Ovenware
When using ovenware, always place it in the middle of the wire
rack.
Ovenware must be heat and steam resistant. Cooking times are
increased when thick-walled ovenware is used.
28
Food which would normally be prepared in a bain-marie should
always be covered with foil (e.g. when melting chocolate).
Grease filter
Leave the grease filter in the cooking compartment for all
applications.
Steam cooking
Steaming is a particularly gentle way of cooking food. The
steam surrounds the dish thereby preventing a loss of nutrients
from the food. Cooking takes place without excess pressure.
As a result, the shape, colour and typical aroma of the dishes
are retained.
Cooking times and quantities
The cooking times when steaming depend on the item size, but
do not depend on the total quantity. The appliance can steam
food to a maximum of 2 kg.
Follow the unit sizes given in the tables. The cooking time is
reduced for smaller pieces and increased for larger ones.
Cooking time is also influenced by the quality and ripeness of
the food. The values quoted can therefore only serve as a
guideline.
Distributing food evenly
Always distribute the food evenly in the ovenware. It will not
cook evenly if the layers are of different depths.
Pressure-sensitive food
When layering delicate foods in the cooking container, do not
pile them too high. It is better to use two containers.
Cooking a menu
With steam, you can cook a whole menu at once, without the
different flavours mixing. Place the food with the longest
cooking time in the appliance first and delay the rest until the
appropriate time. This means that all the food will be ready at
Vegetables
Place the vegetables in the perforated cooking container and
insert at level 3. Insert the baking tray underneath at level 1.
Dripping liquid is caught.
the same time.
The overall cooking time is extended with menu cooking, as a
little steam escapes each time the appliance door is opened
and has to be reheated.
Hot air
The Hot Air operating mode is ideal for sweet and savoury
baking, pot roasts and various cakes.
CircoSteam®
The CircoSteam® operating mode uses a combination of hot
air and steam, and is particularly suitable for the preparation of
roast dishes, chicken and baked items such as yeast-risen
pastry and bread.
Roasts and chicken are nice and crisp on the outside and juicy
inside. What is more, meat loses less of its weight.
Baked items, such as yeast-risen pastry and bread, take on a
particularly attractive surface shine and they do not dry out.
as clean as possible. You can purchase the roasting set as an accessory from specialist
retailers (see section: Accessories)
press down on the roast with a spoon. If it feels firm, it is ready. If the spoon can be
pressed in, it needs to be cooked for a little longer.
Check the shelf height and temperature.
Next time, choose a smaller roasting dish or add more liquid.
Next time, choose a larger roasting dish or add less liquid.
3
1
3
1
mode
Steam cooking 80 - 8512 - 18
Steam cooking 80 - 8515 - 20
Temperature in °C Cooking time
in min.
Fish
FoodAmountAccessoriesLevelOperating
Sea bream, wholeper 0.3 kgPerforated +
Baking tray
Sea bream filletper 0.15 kgPerforated +
Baking tray
Fish terrineBain marie 1.5 l Wire rack 2Steam cooking 70 8040 - 80
Trout, wholeper 0.2 kgPerforated +
Baking tray
Cod filletper 0.15 kgPerforated +
Baking tray
Salmon filletper 0.15 kgPerforated +
Baking tray
Mussels1.5 kgBaking tray2Steam cooking 10010 - 15
Ocean perch filletper 0.15 kgPerforated +
Baking tray
Sole rolls, stuffed-Perforated +
Baking tray
3
1
3
1
3
1
3
1
3
1
3
1
3
1
mode
Steam cooking 80 9015 25
Steam cooking 80 9010 - 20
Steam cooking 80 9012 - 15
Steam cooking 80 9010 - 14
Steam cooking 1008 - 10
Steam cooking 80 9010 - 20
Steam cooking 80 9010 - 20
Temperature in °C Cooking time
in min.
Cooking meat at a low temperature
Low-temperature cooking is the ideal cooking method for all
tender pieces of meat which are to be cooked medium rare or
à point. The meat remains very juicy and turns out as soft as
butter.
Slide the baking tray into the combination steam oven and
preheat with the Low-temperature cooking mode.
Sear the meat on the hob on all sides.
Place in the preheated steam oven and continue to cook gently.
When cooked, arrange on preheated plates and serve with a
hot sauce or gravy.
32
FoodAmountAccessoriesLevelTemperature in °C Cooking time
Boned leg of lamb1 - 1.5 kgBaking tray280140 - 160
Sirloin1.5 - 2.5 kgBaking tray280150 180
Fillet of pork-Baking tray280 9050 - 70
Pork medallions-Baking tray28060 80
Beef steaksapprox. 3 cm thick Baking tray28040 60
Weigh the fruit and add approximately
then add sugar and spices to taste.
Rice pudding
Weigh the rice and add 2.5 times the amount of milk. Ensure
the level of rice and milk in the accessory is no higher than
2.5 cm. Stir after cooking. The remaining milk is quickly
absorbed.
Y the amount of water,
Yoghurt
Heat the milk to 90 °C on the hob. Then leave to cool to 40 °C.
If you are using UHT milk, you do not need to heat it.
Stir in one to two teaspoons of natural yoghurt per 100 ml milk,
or the corresponding amount of yoghurt culture into the milk.
Pour the mixture into clean jars and seal them.
After preparation, leave the glasses to cool in the refrigerator.
The cake collapsesNext time, use less liquid or set the baking temperature 10 °C lower. Note the stirring
The cake has risen in the middle but is
lower around the edge
Cakes baked in a tray or tin are overbrowned at the back
The cake is too dryMake tiny holes in the finished cake using a cocktail stick. Then drizzle fruit juice or an
The bread or cake looks good but it is
soggy inside (overmoist with wet
streaks)
The cake or pastry is unevenly browned Next time, set the temperature a little lower
Use similar items in the baking tables as a guide
Approx. 10 minutes before the end of the baking time stated in the recipe, insert a cocktail stick into the cake at its deepest point. If the cocktail stick comes out clean, the cake
is ready.
times indicated in the recipe.
Do not grease the edge of the springform cake tin. After baking, carefully loosen the
cake using a knife
Place the baking tray in the middle of the accessories, not directly against the rear wall
alcoholic drink over it. Next time, set the temperature 10 °C higher and shorten the baking times or use the CircoSteam® operating mode
Next time, use less liquid. Bake at a lower temperature for a little longer. For cakes with a
moist topping, bake the base first. Cover the base with almonds or bread crumbs first
and then apply the topping. Observe the baking time in the recipe
Reheating food
Using Reheat, dishes can be gently reheated. They taste and
look like they have been freshly prepared. Even baked items
from the day before can be recrisped.
When freezing, lay the food as flat as possible and in portionsized pieces at -18 °C. Do not freeze excessively large
quantities. Once defrosted, food will not keep for as long and
spoils more quickly than fresh food.
Leave the food to defrost in the freezer bag, on a plate or on
the perforated cooking container. Always insert the baking tray
underneath. The food is then not left lying in the defrost water
and the cooking compartment remains clean.
Use the Defrost operating mode.
If necessary, the meal can occasionally be split apart or pieces
which have already defrosted can be removed from the
appliance.
After defrosting, allow the food to stand for a further 5 15 minutes to come up to room temperature.
FoodAmountAccessoriesLevelTemperature in°C Cooking time in
Chicken1 kgperforated +
Chicken drumsticks0.4 kgperforated +
Vegetables frozen in blocks
(e.g. spinach)
Berries0.3 kgperforated +
A
baking tray
baking tray
0.4 kgperforated +
baking tray
baking tray
: Health risk!
When defrosting food from animal sources, you must remove
the liquid that escapes during defrosting. It must never come
into contact with other food. Bacteria could be transferred.
After defrosting, operate the combination steam oven for
15 minutes using Hot air at 180 °C.
Defrost meat
Allow pieces of meat which are to be breadcrumbed to defrost
to the point where seasoning and breadcrumbs adhere to the
meat.
Defrosting poultry
Remove from packaging before defrosting. You must tip the
defrost liquid away.
min.
3
1
3
1
3
1
3
1
45 - 5060 70
45 - 5030 - 35
45 - 5020 30
45 - 505 - 8
35
FoodAmountAccessoriesLevelTemperature in°C Cooking time in
Fish fillet0.4 kgperforated +
baking tray
Whole fish1 kgperforated +
baking tray
Goulash-perforated +
baking tray
Joint of beef-perforated +
baking tray
3
1
3
1
3
1
3
1
45 - 5015 - 20
45 - 5040 50
45 - 5040 50
45 - 5070 80
min.
Dough proving
êUsing the dough proving operating mode, dough rises
considerably quicker than at room temperature.
You may select any shelf position you wish for the wire rack or
place the wire rack carefully on the cooking compartment floor.
N.B.: Do not scratch the cooking compartment floor.
Stand the dough bowl on the wire rack. Do not cover the
dough.
FoodAmountAccessoriesTemperature in °C Cooking time
Yeast dough1 kgBowl + wire rack4020 30
Sourdough1 kgBowl + wire rack4020 30
in min.
Juicing
Before juicing, place the berries in a bowl and sprinkle with
sugar. Leave to stand for at least one hour to draw out the
juice.
FoodAccessoriesLevelOperating
RaspberriesPerforated cooking con-
tainer
+ baking tray
RedcurrantsPerforated cooking con-
tainer
+ baking tray
Add the berries to the perforated cooking container and insert
at level 3. Slide the baking tray into level 1 to catch the juice.
Finally, place the berries in a cloth and squeeze out the rest of
the juice.
Temperature in °C Cooking time
in min.
3
1
3
1
mode
Steam cooking 10030 - 45
Steam cooking 10040 - 50
Preserve
Preserve food which is as fresh as possible. When foods are
stored for a relatively long period, their vitamin content is
reduced and they cook more readily.
Only use fruit and vegetables which are in perfect condition.
The following foods cannot be preserved with your appliance:
Contents of tins, meat, fish or pastry dough.
Check preserving jars, rubber rings, clips and springs.
Clean rubber rings and jars thoroughly with hot water. The
"Sterilise bottles" programme is also suitable for cleaning
glasses.
Place the jars in the perforated cooking container. They must
not be in contact with each other.
After the specified cooking time, open the appliance door.
Do not remove the preserving jars from the appliance until they
have completely cooled down.
These tables have been produced for test institutes to facilitate
the inspection and testing of the various appliances.
Baking
Test dishes tested in accordance with standards EN 50304/
EN 60350 (2009) and IEC 60350.
The values in the table apply to dishes placed in a cold cooking
compartment.
Note: For baking, use the lower of the temperatures indicated
first.
FoodAccessoriesLevelOperating
mode
Piped cookiesBaking tray2Hot air160 17017 - 20
Small cakesBaking tray2Hot air160 17025 - 33
Hot water sponge cake26 cm springform cake tin 2Hot air150 16035 - 40
Double crust apple pie20 cm springform cake tin 2Hot air160 17060 - 70
Temperature in °C Cooking time
in min.
Steaming
Test dishes tested in accordance with standard EN 60350-1.
FoodAccessoriesLevelOperating
Broccoli
(Steam distribution)
Broccoli
(Steam supply)
Peas**
(Maximum load)
* The cooking time for "al dente" must be established beforehand.
** Spread out 2.0 kg of peas evenly in the container.
*** The end of the cooking time has been reached when the peas at the coldest point have reached a temperature of 85 °C.
Perforated +
baking tray
Perforated +
baking tray
Perforated +
baking tray
3
1
3
1
3
1
mode
Steam cooking 100*
Steam cooking 100*
Steam cooking 100***
Temperature in °C Cooking time
in min.
38
39
Constructa Neff
Vertriebs-GmbH
Carl-Wery-Straße 34
D-81739 München
*9000746284*
9000746284
930731
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.