Nedap N V VP4102 Users Manual

VP4102 Reader 434/922 MHz

This sheet is intended as quick start. See service manual for more detailed instructions.

The VP4102 reader is a component that is used to receive data from Smart Tags.

Connections

Compliance statement (part15.19)

This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Déclaration Conformité
Cet appareil se conforme aux normes RSS210 exemptés de license du Industry Canada. L'opération est soumis aux deux
conditions suivantes:
(1) cet appareil ne doit causer aucune interférence, et
(2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de
cet appareil.

Warning (part15.21)

Changes or modifications not expressly approved by party responsible for compliance could void the user’s authority to operate
the equipment. This in particular is applicable for the antenna which can be delivered with the VP4102 System

orange

blue white

blue

black

red

orange white

CAN cable

LAN Ethernet straight cable

white

brown

or

VP4102

CAN cable to VPU (VP8001)

Antenna
922 MHz

Antenna
434 MHz

TIA/EIA 568A TIA/EIA 568B

Antenna default connection is 434MHz. Japan and Korea: switch to 922MHz!

VP4102 – Reader - Quick start 05-2013 Doc.part.no. 9741518 version 1.0 1/ 5

DISPLAY ADDRESS

Shows the actual logic V-pack address

SET ADDRESS

Change the logic address

DISPLAY SECTION

Show section (Default 0, not used for CAN)

SET SECTION

Change section (not used for CAN)

DISPLAY VPU ADDRESS

Shows actual VPU address (one by one)

SET VPU ADDRESS
Changes the actual VPU address (one by one)

SETTINGS TO DEFAULT

All address settings back to factory settings

DHCP IS ON

Press long until blinking to turn on DHCP

DHCP IS OFF

Press long until blinking to turn off DHCP

DISPLAY IP ADDRESS

Shows actual IP address (one by one)

SET IP ADDRESS (only shown in case of DHCP OFF)

192.168.1.101 (not used for CAN)

SET IP ADDRESS

192.168.1.101 (not used for CAN)

SET IP ADDRESS

192.168.1.101 (not used for CAN)

SET IP ADDRESS

192.168.1.101 (not used for CAN)

ACCEPT NEW IP ADDRESS
(not used for CAN)

DISPLAY NETWORK MASK (only shown in case of DHCP OFF)

Shows the network mask (0, 8, 16, 24 or 32) (0= 0.0.0.0, 8= 255.0.0.0 etc.)

SET NETWORK MASK (only shown in case of DHCP OFF)
Changes the network mask (16= 255.255.0.0 etc. 32 = 255.255.255.255)

IP SETTINGS TO DEFAULT

All IP settings back to factory settings

Display Push button

VP4102 – Reader - Quick start 05-2013 Doc.part.no. 9741518 version 1.0 2/ 5

Press button until blinking
Press button short

To leave menu:
press button until display is empty

L1 TEST OUTPUT 1

Signal light

TEST OUTPUT 2

Signal light

TEST FREQUENCY 1

Shows signal strength frequency 1

TEST FREQUENCY 2

Shows signal strength frequency 2

TEST FREQUENCY 3

Shows signal strength frequency 3

TEST FREQUENCY 4

Shows signal strength frequency 4

TEST FREQUENCY 5

Shows signal strength frequency 5

TEST FREQUENCY 6

Shows signal strength frequency 6

RESET UHF CHANNELS SETTINGS TO DEFAULT

All UHF channel settings back to factory settings

DISPLAY ERROR

SE = safeguard error, UE = UHF error.

TRESHOLD RECEPTION (CONFIGURATION MENU)

Enter value to set UHF threshold e.g. …?

FREQUENCY BAND 434MHz (EU/USA)
Press long until blinking to switch to 434Mhz

FREQUENCY BAND 922MHz (Japan/Korea only)
Press long until blinking to switch to 922Mhz

DISPLAYS RSSI STRENGTH OF LAST UHF MESSAGE

View last received RSSI

DISPLAYS NUMBER OF DETECTED UHF DEVICES

(only when UHF network is enabled)

RESTORE FACTORY DEFAULTS

All VP4102 settings back to factory defaults (Default IP address)

VP4102 – Reader - Quick start 05-2013 Doc.part.no. 9741518 version 1.0 3/ 5

POWER

Green on

Power on

off

No power

STATUS

Slow blinking
Fast blinking
1 short flash
2 short flashes
3 short flashes

Operating ok
Downloading or error during download
V-pack not coupled
Firmware present but not active
No firmware present

Display

Blinking

IP fails or CAN fails

V in

Green on

Input power applied

off

No power

Orange

Low power, less than 20V

Orange blinking

Wrong CAN-bus connection, Vin and Vout swapped

Red

Error, plus and minus swapped

V out

Green on

Output power

off

No power

Orange blinking

Low power

Red blinking

Error (overload, shortcut)

LAST

Green on

V-pack is last one on the CAN-bus

off

V-pack is not last one on the CAN-bus

Orange blinking

CAN-bus error and last V-pack on CAN-bus

Red

CAN-bus error

Red blinking

CAN-bus warning / connected wrong

LINK

off

LAN No connection

Green

LAN connection(10 Mbps / 100 Mbps)

ACT

Green flashing

Network activity

off

No network activity

Red

Network error

O1 / O2

Green on

Output on

off

Output off

Red blinking

Output error (overload, shortcut)

UHF

Green on

Data receive

off

No data

Red

UHF Error

Specifications VP 4102

Dimensions

143 x 120 x 68 mm LxWxH (excluding mounting rail) Weight: ± 279 gr

CAN

CAN-bus communication 125 kbit/s

Ethernet

100mbit/s max 100m

Power

Input voltage 12VDC -30 VDC
Power consumption 160mA – 85mA (25VDC 100 mA) (without connected I/O such as
signal lamp)
Protected against reverse connection power supply

Software

Downloadable by the CAN network or ethernet

Outputs

Max. 0.4 Amp by current limiter, short-circuiting and thermal protected

Antennas

G-CXL 70-1LW/h nedap art. 4602366

Detection distance

Lactivator Realtime labels: +/- 50m dependable of antenna situation

Environment

Temperature: Operating: -10 – 55 °C, Storage: -25 – 70 °C
Relative humidity: 10 – 93% non condensing

IP class

IP 30. When installed in V-box IP 65 (cover and cables installed correctly !)

Always use a NEDAP power supply VP2001 or VP2002. The Nedap guarantee-regulations are only valid when is
installed as indicated in this manual. Install data cables at a safe distance from (high) powered cables
For more detailed information contact your local Nedap supplier or check the internet site.

LED indicators

VP4102 – Reader - Quick start 05-2013 Doc.part.no. 9741518 version 1.0 4/ 5

POWER

Green on

Power on

off

No power

STATUS

Slow blinking
Fast blinking
1 short flash
2 short flashes
3 short flashes

Operating ok
Downloading or error during download
V-pack not coupled
Firmware present but not active
No firmware present

Display

Blinking

IP fails or CAN fails

V in

Green on

Input power applied

off

No power

Orange

Low power, less than 20V

Orange blinking

Wrong CAN-bus connection, Vin and Vout swapped

Red

Error, plus and minus swapped

V out

Green on

Output power

off

No power

Orange blinking

Low power

Red blinking

Error (overload, shortcut)

LAST

Green on

V-pack is last one on the CAN-bus

off

V-pack is not last one on the CAN-bus

Orange blinking

CAN-bus error and last V-pack on CAN-bus

Red

CAN-bus error

Red blinking

CAN-bus warning / connected wrong

LINK

off

LAN No connection

Green

LAN connection(10 Mbps / 100 Mbps)

ACT

Green flashing

Network activity

off

No network activity

Red

Network error

O1 / O2

Green on

Output on

off

Output off

Red blinking

Output error (overload, shortcut)

UHF

Green on

Data receive

off

No data

Red

UHF Error

Specifications VP 4102

Dimensions

143 x 120 x 68 mm LxWxH (excluding mounting rail) Weight: ± 279 gr

CAN

CAN-bus communication 125 kbit/s

Ethernet

100mbit/s max 100m

Power

Input voltage 12VDC -30 VDC
Power consumption 160mA – 85mA (25VDC 100 mA) (without connected I/O such as
signal lamp)
Protected against reverse connection power supply

Software

Downloadable by the CAN network or ethernet

Outputs

Max. 0.4 Amp by current limiter, short-circuiting and thermal protected

Antennas

G-CXL 70-1LW/h nedap art. 4602366

Detection distance

Lactivator Realtime labels: +/- 50m dependable of antenna situation

Environment

Temperature: Operating: -10 – 55 °C, Storage: -25 – 70 °C
Relative humidity: 10 – 93% non condensing

IP class

IP 30. When installed in V-box IP 65 (cover and cables installed correctly !)

Always use a NEDAP power supply VP2001 or VP2002. The Nedap guarantee-regulations are only valid when is
installed as indicated in this manual. Install data cables at a safe distance from (high) powered cables
For more detailed information contact your local Nedap supplier or check the internet site.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.

This radio transmitter with certification number 1444A-VP4102 has been approved by Industry Canada to operate with the antenna
type listed below and with the maximum permissible gain and required antenna impedance indicated. Antenna types not included
in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Model: G-CXL 70-1LW/h (nedap art. 4602366)
Antenna gain: 2 dBi
Nominal impedance: 50 Ω

LED indicators

VP4102 – Reader - Quick start 05-2013 Doc.part.no. 9741518 version 1.0 4/ 5