Nedap N V STOREIDT Users Manual

!D Top

-AYYYY-MM-DD

Documentation released

-

Ref.Nr.

REV.

DATE

DESCRIPTION

APPROVED

DIM. IN MM

ROUGHNESS ACC.

ISO 1302 in µM

GENERAL TOLERANCES

SCALE:

FORMAT:

Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this

A

B

C

D

E

F

6

3

2

1

A3

9954139

N/A

A.01

ARTICLE NUMBER

REV.

ISO A

GROENLO HOLLAND

SHEET:

4

7

8

5

10.01 OF 1

1:5

± 1°

± 0.2

DESCRIPTION

LIN.

ANG.

N/A

??

??

??

DRW:

CHCK:

YYYY-MM-DD

YYYY-MM-DD

YYYY-MM-DD

DSGN:

5

8(4x)

D

E

F

7

8

D

E

F

7

8

!D Top mounting template for ceiling

The !D top is most stable when the wires form a
broader basis (see picture on the right).
To make this mounting template more rigid

h

use the cardboard packaging of the !D top

steps for mounting !D Top on the ceiling

1. determine the position of the !D top in store

2. measure the height between !D top and ceiling

3. find the corresponding mounting holes on this

height max. 250 cm

part no. 9741291

drawing no. t9741-291a

height max. 250 cm

template, closest to the measured height

4. position this template to the ceiling and mark the
four mounting holes (pierce through the paper)

5. drill the holes, connect the cables and the !D top

height max. 200 cm

height max. 200 cm

height max. 150 cm

height max. 150 cm

height max. 100 cm

height max. 100 cm

height max. 50 cm

height max. 50 cm

height max. 25 cm

height max. 25 cm

height max. 25 cm

height max. 25 cm

height max. 50 cm

height max. 50 cm

height max. 100 cm

height max. 100 cm

height max. 150 cm

height max. 150 cm

height max. 200 cm

height max. 200 cm

height max. 250 cm

height max. 250 cm

1x !D Top

3x Tie-wrap4x Mounting set

dimensions remove cover

198.5mm / 7.8”

500mm / 1.6ft

500

198,5

65mm / 2.6”

84,5

65

84.5mm / 3.3”

50(4x)

35(4x)

7(4x)

4(8x)

7(4x)

265

265mm / 10.4”

900mm / 3ft

900

DETAIL A

distance between antennas

recommended - 2.0m/6.6ft
absolute max. - 2.4m/7.9ft

recommended - 3.0m/9.8ft
absolute max. - 3.5m/11.5ft

2x Bracket (wall mounting)

1

2

2m / 6ft 2m / 6ft

1m / 3ft 1m / 3ft

1

2

2m / 6ft2m / 6ft

1m / 3ft1m / 3ft

required label free zone

1x Poster

1

2

oor

recommended label free zone

orientation in the shop

Power inserter

sales oor stock room

all antennas
in the same
direction.

drw: CB 2013/05/29

description:

quick reference !D Top

GROENLO - HOLLAND

chk:

doc. article no: 5279615

rev. : B.01

Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be repro­duced or distributed in any form or by any means, or stored in a data base or retrieval system without the
prior written permission of NEDAP.

sheet: 45.01 of 1

drawing: T5279-615

drilling holes (poster recommended)

(not included)

4x plugs S6 (recommended)

4x screw 4x40 (recommended)

ceiling

520mm / 1.7ft

520

220

220mm / 8.7”

!D Top ceiling installation

ceiling

steel-cable

adjust height
press here.

01

ceiling

top-view

included

not included

02

steel-cable

processing unit

C

D

E

F

10

7

2

1

8

11

12

9

3

4

5

6

G

H

Power for Reader
network IN
USB host
network OUT
USB service port

1 Green Processing unit at output

2 Blue Blink No device at output

Blue Continuous Power inserter at output

3 Red Power error

power supply

Power supply 9561811. One needed for
every installed system. (not included)

Not compatible with IEEE 802.3a* standard

Recommended to place in switch-room

1 Yellow Heartbeat

2 Green Disk access

3

1 2

3 Green Firmware running

+

buzzer

-

Out

In

previous

!D Reader

next

Led Blue Orange Red Green Green

-

Firmware running Error RFID active Power

01

installation of

power-supply OUT

one !D Top

x cable with

tie-wrap

ceiling

mounting power cable

note:
use only cat5e ethernet cable or better,
with all 8 wires connected.

unit - network IN

02

installation of
one !D Top

ceiling

mounting ethernet cable

note:
use only cat5e ethernet cable or better,
with all 8 wires connected.

x cable with

tie-wrap

RJ45 connector to ethernet
outlet - customer network.

01

installation of
two !D Tops

!D-Top - 1

place cover

x cable with

tie-wrap

note:
use only cat5e ethernet cable or better,
with all 8 wires connected.

RJ45 connector to ethernet
outlet - customer network.

ceiling

x cable with

tie-wrap

!D-Top - 2

unit - network OUT unit - network IN

2

connect voltage supply

2

2

Note :

1

1

1

230V
110V

The start up of all the
processes takes
approximately 3 minutes.

Model: !D Top Region 2
FCC ID: CGDSTOREIDT IC: 1444A-STOREIDT

Model: !D Top Region 2
FCC ID: CGDSTOREIDT IC: 1444A-STOREIDT

This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada.

L’opération est soumis aux deux conditions suivantes:

(1) cet appareil ne doit causer aucune interférence, et

(2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu

de cet appareil.

Les changements ou modications n’ayant pas été expressément approuvés par la partie responsable de la conformité peuvent
faire perdre à l’utilisateur l’autorisation de faire fonctionner le matériel.

FCC and IC Radiation Exposure Statement:
This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 22 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme a RSS-102 limites énoncées pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec une distance minimale de 22 cm entre le radiateur et votre corps.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.