NEC Versa P700 Disassembly Manual

NEC

Versa P700

Disassembly Manual

Table of contents

Overview.................................................................................................................................................................3

Technician Notes....................................................................................................................................................3

Disassembly Instructions........................................................................................................................................3

Reassembly Instructions ........................................................................................................................................3

Required Tools .......................................................................................................................................................3

Hazardous Voltage .................................................................................................................................................4

Avoid Electrostatic Discharge.................................................................................................................................4

Power Supply Unit..................................................................................................................................................4

Removing the Battery.............................................................................................................................................5

Removing the VersaBay IV ....................................................................................................................................5

Removing the MultyBay .........................................................................................................................................6

Removing the Wireless Mini PCI Card ...................................................................................................................6

Removing the MDC modem ...................................................................................................................................7

Removing the Memory Module ..............................................................................................................................7

Removing the Keyboard.........................................................................................................................................8

Removing the LED Assy ........................................................................................................................................9

Removing the LCD display...................................................................................................................................10

Disassembling the LCD display............................................................................................................................12

Removing the Hard Disk Drive .............................................................................................................................15

Removing the Touchpad ......................................................................................................................................17

Removing the Speaker Set ..................................................................................................................................18

Removing the CPU...............................................................................................................................................19

Removing the Heat Plate .....................................................................................................................................20

Removing the CMOS Battery ...............................................................................................................................20

Removing the Plastic Cover .................................................................................................................................21

Removing the Power Switch ................................................................................................................................22

Removing the Wireless LED Board......................................................................................................................22

Removing the IDE/Audio Board and Microphone ................................................................................................23

Removing the Main Board....................................................................................................................................24

Removing the Video Board ..................................................................................................................................26

Screws..................................................................................................................................................................27

Notice ...................................................................................................................................................................29

NEC Versa P700 Disassembly Manual

Page 2

Overview

This document contains step-by-step disassembly instructions for the Versa P700 chassis. The instructions are
illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws
that are removed are shown next to the image of the parts themselves.

NEC reserves the right to make changes to the Versa P700 chassis without notice.

Technician Notes

Only technicians authorized by NEC Computers International BV should attempt to repair this equipment. All
troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the
complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component
level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modifications may void any warranty or exchange
allowances.

Disassembly Instructions

When disassembling the system unit, follow these general rules:

 Do not disassemble the system into parts that are smaller than those specified in the instructions.
 Label all removed connectors. Note where the connector goes and in what position it was installed.
 Turn off the power and disconnect all power and all options.

Reassembly Instructions

Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned
to their proper positions. Check that no tools or any loose parts have been left inside the chassis. Check that
everything is properly installed and tightened.

Required Tools

All disassembly procedures can be performed using the following tools:

 Tweezers
 Small Philips screwdriver
 Small Flatbed screwdriver
 HEX bold screwdriver Ø 5 MM
 A plastic flatbed screwdriver

NEC Versa P700 Disassembly Manual

Page 3

Hazardous Voltage

There is hazardous voltage present inside the computer
when it is connected to an AC supply, even when the
computer’s power switch is off. Exposure to hazardous
voltage could cause personal injury. To avoid risk of injury,
contact an Authorized Service Provider for proper
(un)installation of optional hardware devices.

Avoid Electrostatic Discharge

Electrostatic electricity can easily damage circuit cards and
integrated circuits (ICs). To reduce risk of damage, store
them in protective packaging whenever they are not
installed in your system.

Add-in cards can be extremely sensitive to ESD and always
require careful handling. After removing the card from the
computer, place the card flat on a grounded, static-free
surface, component-side up. Use a conductive foam pad if
available, but not the card wrapper. Do not slide the card
over any surface.

Before you install or remove memory modules, video
memory, disk drives, circuit cards or other devices, protect
them from static electricity. To do so, make sure your
computer’s power switch is OFF. Then, unplug the
computer’s AC power cord. Before picking up the device you
(un)install, you should wear an anti-static wrist wrap
(available at electronic supply stores). Be sure to connect
the wrist wrap to an unpainted metal portion of the computer
chassis. As an alternative, you can dissipate electrostatic
build-up by touching an unpainted metal portion of the
computer chassis with one hand. Then touch the device you
are (un)installing with the other hand, and maintain
continuous contact with it until it is (un)installed in the
computer.

Power Supply Unit

Under no circumstances should you attempt to disassemble
the power supply. The power supply contains no user­serviceable parts. Inside the power supply are hazardous
voltages that can cause serious personal injury. Always
return a defective power supply to your dealer.

WARNING

Ensure that the computer is disconnected from
its power source and from all
telecommunications links, networks, or modem
lines whenever the chassis cover is removed.
Do not operate the computer with the cover
removed.

AVERTISSEMENT

Assurez-vous que le système est débranché de
son alimentation ainsi que de toutes les
liaisons de télécommunication, des réseaux, et
des lignes de modem avant d’enlever le capot.
Ne pas utiliser le système quand le capot est
enlevé.

WARNUNG

Das System darf weder an eine Stromquelle
angeschlossen sein noch eine Verbindung mit
einer Telekommunikationseinrichtung, einem
Netzwerk oder einer Modem-Leitung haben,
wenn die Gehäuseabdeckung entfernt wird.
Nehmen Sie das System nicht ohne die
Abdeckung in Betrieb.

ADVERTENCIA

Asegúrese de que cada vez que se quite la
cubierta del chasis, el sistema haya sido
desconectado de la red de alimentación y de
todos lo enlaces de telecomunicaciones, de red
y de líneas de módem. No ponga en
funcionamiento el sistema mientras la cubierta
esté quitada.

WAARSCHUWING

Zorg er voor dat alle verbindingen van en naar
de computer (stroom, modem netwerk, etc)
verbroken worden voordat de behuizing
geopend wordt. Zet de computer nooit aan als
de behuizing geopend is.

AVVERTENZA

Prima di rimuovere il coperchio del telaio,
assicurarsi che il sistema sia scollegato
dall’alimentazione, da tutti i collegamenti di
comunicazione, reti o linee di modem. Non
avviare il sistema senza aver prima messo a
posto il coperchio

NEC Versa P700 Disassembly Manual

Page 4

Removing the Battery

Perform the following steps to remove the battery:

1. Make sure the notebook is powered off.

2. Close the lid of the notebook

3. Turn the unit upside down

4. Unlock the battery and lift it out of its place as shown here.

Fig. 1: Removing the battery

Removing the VersaBay IV

Perform the following steps to remove the VersaBay IV:

5. Slide the latch as shown in the image below to unlock the VersaBay IV

Fig. 2: Removing the VersaBay IV.

6. Carefully extract the VersaBay IV from its location.

NEC Versa P700 Disassembly Manual

Page 5

Removing the MultyBay

Perform the following steps to remove the MultyBay:

1. Slide the latch as shown in the image below to unlock the MultyBay.

Fig. 3: Removing the MultyBay

2. Carefully extract the MultyBay from its location.

Removing the Wireless Mini PCI Card

Perform the following steps to remove the Wireless Mini PCI Card:

1. Unscrew one screw to open the cover assy.

2. Carefully disconnect the two antenna wires connected to the wireless mini PCI card.

Fig. 4: Removing the Mini PCI Antenna wires

3. Pull apart the retaining clips, to release the mini PCI card.

NEC Versa P700 Disassembly Manual

(M2.5x3)

Page 6

Fig. 5: Releasing the Mini PCI card

4. Remove the mini PCI wireless card.

Removing the MDC modem

Perform the following steps to remove the Wireless Mini PCI Card:

1. Unscrew one screw to open the cover assy.

2. Unscrew the two black screws.

(M2.5x3)

Fig. 6: Removing the modem screws

3. Disconnect the modem by pulling it away carefully.

Removing the Memory Module

Perform the following steps to remove the memory module:

1. Unscrew one screw to open the cover assy.

2. Pull apart the retaining clips in order to release the memory module.

NEC Versa P700 Disassembly Manual

(M2x4)

(M2.5x3)

Page 7

Fig. 7: Removing the memory module

Removing the Keyboard

Perform the following steps to remove the keyboard:

1. Carefully insert a flatbed screwdriver between the function keys and the keyboard cover.

Fig. 8: Removing the keyboard cover

2. Lever until the keyboard cover comes loose. Then put the keyboard cover aside.

3. Carefully lift the keyboard and put it face down on the front part of the notebook taking
care not to rip off the keyboard cable.

4. Locate the connector on the main board where the keyboard cable is attached.

NEC Versa P700 Disassembly Manual

Page 8

Fig. 9: Disconnecting the keyboard cable

5. Gently pull the connector latch as shown above, to release the keyboard cable.

6. Take the keyboard off the notebook and put it aside.

Removing the LED Assy

To remove the LED assy, first remove the keyboard cover (see Removing the Keyboard) and
then perform the following steps:

1. Extract the antenna cable that passes to the hole in the LED assy and goes to the
Wireless Mini PCI Card.

Note: You will need to disconnect the antenna cable from the Wireless Mini PCI Card if you have not
done so previously. Refer to the section Removing the Wireless Mini PCI Card for instructions.

2. Disconnect the flat cable from the LED assy, by unlocking the retaining latch and
carefully removing the cable as shown here.

Fig. 10: Disconnecting the flat cable from the LED assy

3. Now disconnect the flat cable from the main board as shown below and put it aside:

NEC Versa P700 Disassembly Manual

Page 9

Fig. 11: Disconnecting the flat cable of the LED assy from the main board

4. Remove the screws marked in the next picture.

Fig. 12: Unscrewing the LED assy

5. Finally carefully remove the LED assy and put it aside.

Removing the LCD display

To remove the LCD display, first remove the keyboard cover (see Removing the Keyboard),
disconnect the antenna from the Wireless Mini PCI Card (see the section Removing the

Wireless Mini PCI Card), then perform the following steps:

1. Close the LCD cover.

2. Turn the notebook up-side down.

3. Remove the two screws shown in the picture that follows:

A (M2.5x9)

B (M2x3)

NEC Versa P700 Disassembly Manual

Page 10

Fig. 13: Removing the bottom screws of the LCD

6. Remove the screws shown in the next picture.

Fig. 14: Removing the back screws of the LCD

7. Now turn the notebook back in the normal position and open the cover.

8. Remove the screws holding the LCD hinge shown below.

(M2.5x9)

(M2.5x5)

A (M2.5x5)

B (M2.5x3)

Fig. 15: Removing the LCD hinge screws

9. Remove the screw holding the LCD flat cable connector onto the main board.

NEC Versa P700 Disassembly Manual

Page 11

Fig. 16: Releasing the LCD flat cable connector

10. Finally carefully lift away the whole LCD display from the notebook.

Disassembling the LCD display

To disassemble the LCD display, first it has to be removed from the notebook. Refer to the
section Removing the LCD Display for instructions on how to do that. After removing LCD
display do as follows:

1. Remove the four rubber tabs and the two stickers that seal the retaining screws of the
frame cover.

A (M2.5x5)

Sticker

Rubber

A (M2x5)

B (M2.5x5)

Fig. 17: Removing LCD rubber tabs and screw seals

2. Remove the screws discovered by removing the rubber tabs and the stickers in the
previous step.

3. Unclip the LCD front cover from the back LCD cover and put it a side.

NEC Versa P700 Disassembly Manual

Page 12

Fig. 18: Detail of the clips found all around the LCD cover

Note: Use extreme caution when unclipping the LCD front cover. There are a great number of plastic
indentations that hold the two parts strongly together. Taking the covers apart might cause the indenting
clips to break if the operation is not carefully performed.

4. Remove the plastic hinge cover from the assembly, carefully freeing it from the antenna
cables and the flat cable.

Fig. 19: Removing plastic hinge

5. Remove the screw that holds the LCD inverter board in position and the screw holding
the cable on the frame, then carefully lift the LCD inverter board from its location.

(M2x3)

Fig. 20: Removing LCD inverter board screw

6. Disconnect the connectors from the LCD inverter board and put the inverter board aside.

NEC Versa P700 Disassembly Manual

Page 13

Fig. 21: Disconnecting the connectors fo the LCD inverter board

7. Remove the two screws shown below..

Fig. 22: Removing the bottom screws of the hinge

8. Remove, on both sides of the LCD assembly, the screws shown in the next picture.

Fig. 23: Removing antenna and hinge screws

Note: At the right side of the LCD assembly, all four screws have all the same size namely M2x3

9. Carefully remove the LCD from the back cover.

10. Remove the screws marked in the next picture to free the bare LCD panel from the
hinges.

(M2.5x5)

A (M2x3)

B (M2x2)

Fig. 24: Removing hinges screws

11. Turn the LCD panel face down.

(M2x2)

NEC Versa P700 Disassembly Manual

Page 14

12. Disconnect the LCD cable at the back from the LCD panel.

Fig. 25: Removing the LCD cable

Note: The LCD cable connector is hold in place with the aid of an additional transparent adhesive tape.
Be careful when removing the tape, not to cause any damage to either cable or connector.

Removing the Hard Disk Drive

Perform the following steps to remove the hard disk drive:

1. Turn the notebook up-side down.

2. Remove the screws shown in the picture below

(M2.5x12)

Fig. 26: Removing the hard disk drive cover screws

3. Turn the notebook back in the normal position.

4. Remove the hard disk drive cover sliding out of its position it as shown next.

NEC Versa P700 Disassembly Manual

Page 15

Fig. 27: Removing the hard disk drive cover

5. Slide the hard disk drive as shown in the next picture to disconnect it and carefully lift it
out of the system.

Fig. 28: Removing the hard disk drive

6. Finally remove the black screws shown next to free the hard disk drive from its brackets.

(M3x3)

Fig. 29: Removing the bracket screws

NEC Versa P700 Disassembly Manual

Page 16

Removing the Touchpad

Perform the following steps to remove the touchpad:

1. Turn the notebook up-side down.

2. Remove the screws shown in the picture below.

Fig. 30: Removing the touchpad and the hard disk drive cover screws

3. Remove the hard disk drive cover as explained in the section Removing the Hard Disk

Drive.

4. Carefully lift and tilt the touchpad assembly and lay it face down on the system.

Note: Observe care when performing this operation. The touchpad is still connected to the system via a
small flat cable that might damage if you do not operate carefully.

5. Disconnect the flat cable of the touchpad from the system as shown below. Now you can
remove the touchpad assembly from the system.

Fig. 31: Disconnecting the touchpad flat cable

6. With the back of the touchpad assembly still facing up, remove the flat cable from the
assembly.

A (M2.5x9)

B (M2.5x3)

C (M2.5x12)

NEC Versa P700 Disassembly Manual

Page 17

Fig. 32: Removing the flat cable from the touchpad

7. Remove the screws marked in the next picture and finally lift the touchpad out of the
assembly.

A (M2x3)

Fig. 33: Removing the touchpad screws

Removing the Speaker Set

To remove the speaker set, first remove the Hard disk drive cover (see Removing the Hard

Disk Drive), remove the touchpad assembly (see Removing the Touchpad), then perform the

next steps:

1. Remove the one screw holding down the left speaker.

2. Disconnect the speakers from the audio board (refer to the picture below for the location
of screw and connector mentioned).

Fig. 34: Removing the speaker set

NEC Versa P700 Disassembly Manual

B (M2x3)

(M2x6)

Page 18

Removing the CPU

To remove the CPU, first remove the keyboard (see Removing the Keyboard) then perform
the following steps:

1. Remove the two black screws at the left side of the heat sink and loosen the four other
screws in the center of the heat sink

A (M2x4)

Fig. 35: Removing the heat sink

2. Remove the conducting tape connecting the heat sink with the heat plate.

3. Carefully lift the heat sink and disconnect the two CPU fan connectors.

Fig. 36: Removing the CPU fan connectors

4. Unlock the CPU with an appropriate screwdriver by turning CPU lock anti clockwise.

NEC Versa P700 Disassembly Manual

Page 19

Fig. 37: Unlocking the CPU

5. Carefully lift the CPU from the CPU socket and put it aside.

Removing the Heat Plate

To remove the heat plate, first remove the keyboard (see Removing the Keyboard), remove
the LED assy (see Removing the LED Assy), remove the heat sink (see Removing the CPU),
remove the Hard disk drive cover (see Removing the Hard Disk Drive
assembly (see Removing the Touchpad), then perform the following steps:

1. Remove the seven screws marked in the next picture.

), remove the touchpad

Fig. 38: Removing the heat plate screws

2. Carefully lift out the front side of heat plate from the system, slide the heat plate slightly
towards the left side to free it from the plastic cover and put it aside.

Removing the CMOS Battery

To remove the CMOS battery, first remove the keyboard (see Removing the Keyboard), then
follow the next steps:

1. Disconnect the battery connector from the main board (see picture below).

A (M2x2)

B (M2x10)

C (M2.5x5)

D (M2x4)

NEC Versa P700 Disassembly Manual

Page 20

Fig. 39: Disconnecting the CMOS battery

2. Take the battery out of the system and put it aside.

Removing the Plastic Cover

To remove the plastic cover, first remove the keyboard (see Removing the Keyboard), remove
the LED assy (see Removing the LED Assy), remove the LCD assembly (see Removing the

LCD Display), remove the heat sink (see Removing the CPU), remove the Hard disk drive

cover (see Removing the Hard Disk Drive), remove the touchpad assembly (see Removing

the Touchpad), remove the heat plate (see Removing the Heat Plate), then perform the next

steps:

1. Remove the screw on the bottom of the system at the VersaBay location (see picture
below).

A (M2x4)

(Cone 2.5X3)

Fig. 40: Removing screw in VersaBay location

2. Remove the screws marked in the next picture

B (M2.5x5)

Fig. 41: Removing the plastic cover

NEC Versa P700 Disassembly Manual

Page 21

3. Carefully lift the front side of the plastic cover.

4. Flip over the plastic cover along the top edge.

5. Disconnect the power switch connector shown in the next picture after having
disconnected the other end of the same cable on the main board..

Fig. 42: Disconnecting the power switch connector

6. Now remove the plastic cover and put it aside.

Removing the Power Switch

To remove the power switch, first remove the keyboard (see Removing the Keyboard),
remove the LED assy (see Removing the LED Assy), remove the LCD assembly (see

Removing the LCD Display), remove the heat sink (see Removing the CPU), remove the Hard

disk drive cover (see Removing the Hard Disk Drive

Removing the Touchpad), remove the heat plate (see Removing the Heat Plate), remove the

plastic cover (see Removing the Plastic Cover), then perform the next steps:

1. Take the plastic cover that was removed in the section Removing the Plastic Cover .

2. Turn the plastic cover up-side down.

3. Remove the one screw holding the power switch to the plastic cover and put the power
switch aside..

), remove the touchpad assembly (see

Fig. 43: Removing the power switch

Removing the Wireless LED Board

To remove the wireless LED board, first remove the keyboard (see Removing the Keyboard),
remove the LED assy (see Removing the LED Assy), remove the LCD assembly (see

NEC Versa P700 Disassembly Manual

(M2x3)

Page 22

Removing the LCD Display), remove the heat sink (see Removing the CPU), remove the Hard

disk drive cover (see Removing the Hard Disk Drive

), remove the touchpad assembly (see

Removing the Touchpad), remove the heat plate (see Removing the Heat Plate), remove the

plastic cover (see Removing the Plastic Cover), then perform the next steps:

1. Remove the screw holding the LED board in place.

2. Disconnect the LED board connector from the main board and put the LED board aside.

Fig. 44: Removing the wireless LED board

Removing the IDE/Audio Board and Microphone

To remove the IDE/Audio board and microphone, first remove the keyboard (see Removing

the Keyboard), remove the LED assy (see Removing the LED Assy), remove the LCD

assembly (see Removing the LCD Display), remove the heat sink (see Removing the CPU),
remove the Hard disk drive (see Removing the Hard Disk Drive), remove the touchpad
assembly (see Removing the Touchpad), remove the heat plate (see Removing the Heat

Plate), remove the plastic cover (see Removing the Plastic Cover), then perform the next

steps:

1. Disconnect the speaker set connector (see Removing the Speaker Set).

2. Disconnect the microphone connector and put the microphone aside.

3. Remove the screws marked in the picture below.

(M2x3)

(M2.5x5)

Fig. 45: Removing the IDE/Audio board

NEC Versa P700 Disassembly Manual

Page 23

4. Carefully lift the IDE/Audio vertically to disconnect it from the main board and put it
aside.

Note: The IDE/Audio board is connected to the main board through two connectors. These connectors
are located underneath the IDE/Audio board.

Removing the Main Board

To remove the main Board, first remove the keyboard (see Removing the Keyboard), remove
the LED assy (see Removing the LED Assy), remove the LCD assembly (see Removing the

LCD Display), remove the heat sink (see Removing the CPU), remove the Hard disk drive

(see Removing the Hard Disk Drive), remove the touchpad assembly (see Removing the

Touchpad), remove the heat plate (see Removing the Heat Plate), remove the plastic cover

(see Removing the Plastic Cover), remove the wireless LED board (see Removing the

Wireless LED Board), remove the speaker set (see Removing the Speaker Set), remove the

IDE/Audio board (see Removing the IDE/Audio Board and Microphone
steps:

1. Remove the last two screws holding the heat sink covering the chipset..

), then follow the next

(M2x3)

Fig. 46: Removing chipset heat sink

2. Remove the two screws shown next and take out the metal brackets that the screws
held in place.

(M2.5x5)

Fig. 47: Removing brackets

NEC Versa P700 Disassembly Manual

Page 24

3. Remove the one screw holding the metal plate at the VersaBay location, remove the
plate and put it aside.

Fig. 48: Removing metal plate at VersaBay location

4. Remove the screws marked below, that hold the rails for the Multibay.

Fig. 49: Removing the MultiBay rails

5. Now you can remove the screw, disconnect the lid switch and put it aside.

(M2.5x5)

A (HEX 12 mm)

B (M2x4)

C (M2x6)

(M1.5x6)

Fig. 50: Removing the lid switch

6. Remove the screws at the back of the notebook as shown.

NEC Versa P700 Disassembly Manual

Page 25

Fig. 51: Removing screws on back of notebook

7. Removed the screws marked below.

Fig. 52: Removing main board screws

(HEX 5 mm)

A (HEX 16 mm)

B (HEX 10 mm)

C (HEX 12 mm)

8. Carefully extract the main board from the base assembly.

Note: Underneath the main board there is still the video board connected. If the memory module, the
Wireless Mini PCI Card and the modem have not previously been removed, they will also be still on the
motherboard on the same side as the video board. Please refer to Removing the Memory Module

Removing the Wireless Mini PCI Card

, Removing the MDC Modem, for instructions on the removal of

such parts.

Removing the Video Board

To remove the video board, first remove the main board (see Removing the Main Board) then
follow the next steps:

1. Take the main board and flip it over.

D (HEX 12 mm

w/groove)

,

E (HEX 7 mm

w/groove)

F (HEX 8 mm)

G (M2x4)

J (M2x3)

H (Cone 2.5x3)

K (M2.5x3)

NEC Versa P700 Disassembly Manual

Page 26

2. Remove the screws retaining the video board to the main board.

Fig. 53: Removing the video board

3. Carefully pull away the video board which is still attached to the main board through
connectors and put it aside.

Screws

HEX Spacer 5 mm HEX Spacer 8 mm HEX Spacer 10 mm HEX Spacer 12 mm HEX Spacer 16 mm

HEX Spacer

w/groove 12 mm

M2x4 mm M2x3 mm M3x3 mm M2x3 mm M2x3 mm M2x2

M2x5 mm M2x6 mm Cone 2.5x3 mm M1.5x6 mm

M2x10 mm M2.5x3 mm M2.5x5 mm M2.5x9 mm M2.5x12 mm

NEC Versa P700 Disassembly Manual

HEX Spacer

w/groove 7 mm

(M2.5x5)

Page 27

NEC Versa P700 Disassembly Manual

Page 28

Notice

The information in this guide is subject to change without notice.

This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in
any form or by any means without prior written consent from NEC Computers International BV.

NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS
OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.

Copyright © 2003 NEC Computers International BV. All rights reserved.

NEC is a trademark of NEC Computers International BV.
The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks
of their respective owners.

The software described in this guide is furnished under a license agreement or nondisclosure agreement. The
software may be used or copied only in accordance with the terms of the agreement.

Versa P700 Disassembly Manual

Authors: Vincenzo D'Apice
Daniel Bensoussan
First Edition: January 2003
Version: 1.0

NEC
A division of NEC Computers International BV

NEC Versa P700 Disassembly Manual

Page 29