NEC N8100-1005F, Express5800/110Ei User Manual

N8100-1005F

NEC Express5800/110Ei

User's Guide

1st Edition

11-2004

ONL-3125aN-110Ei-100-99-0411

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related materials, is the
valuable property of NEC Corporation (NEC) and /or its licensors. NEC and/or its licensors, as
appropriate, reserve all patent, copyright and other proprietary rights to this document, including all
design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are
expressly granted to others.

The NEC product(s) discussed in this document are warranted in accordance with the terms of the
Warranty Statement accompanying each product. However, actual performance of each such
product is dependent upon factors such as system configuration, customer data, and operator control.
Since implementation by customers of each product may vary, the suitability of specific product
configurations and applications must be determined by the customer and is not warranted by NEC.

To allow for design and specification improvements, the information in this document is subject to
change at any time, without notice. Reproduction of this document or portions thereof without
prior written approval of NEC is prohibited.

First Printing, November 2004

Copyright 2004

NEC Corporation

7-1 Shiba 5-Chome, Minato-Ku

Tokyo 108-8001, Japan

All Rights Reserved

Printed in Japan

Keep this manual at hand for quick reference at anytime necessary.

SAFETY INDICATIONS

Follow the instructions in this manual for your safety to use the NEC Express server.

Your server contains components with possible danger, hazards that may cause by ignoring
warnings, and preventive actions against such hazards.

Server components with possible danger are indicated with a warning label placed on or around them
as well as described in this manual.

In this manual or warning labels, "WARNING" or "CAUTION" is used to indicate a degree of danger.
These terms are defined as follows:

WARNING

Indicates the presence of a hazard that may result in death or serious
personal injury if the instruction is ignored.

CAUTION

Indicates the presence of a hazard that may cause minor personal injury,
including burns, or property damage if the instruction is ignored.

Precautions and notices against hazards are presented with one of the following three symbols. The
individual symbols are defined as follows:

This symbol indicates the presence of a hazard if the instruction is ignored.
An image in the symbol illustrates the hazard type. (Attention)

This symbol indicates prohibited actions. An image in the symbol illustrates a
particular prohibited action. (Prohibited Action)

This symbol indicates mandatory actions. An image in the symbol illustrates a
mandatory action to avoid a particular hazard. (Mandatory Action)

(Example)

Symbol to draw attention

Term indicating a degree of danger

CAUTION

High temperature.
Immediately after the server is powered off, its internal components such as
hard disks are very hot. Leave the server until its internal components fully
cool down before installing/removing any component.

Symbol indicating a prohibited
action (may not always be
indicated)

Description of a danger

SYMBOLS USED IN THIS MANUAL AND WARNING LABELS

Attentions

Indicates that improper use may cause an electric shock.

Indicates that improper use may cause personal injury.

Indicates that improper use may cause fingers to be caught.

Indicates that improper use may cause fumes or fire.

Indicates a general notice or warning that cannot be specifically identified.

Indicates that improper use may cause loss of eyesight due to laser beam.

Prohibited Actions

Indicates a general prohibited action that cannot be specifically identified.

Do not disassemble, repair, or modify the server. Otherwise, an electric shock or fire
may be caused.

Mandatory Action

Unplug the power cord of the server. Otherwise, an electric shock or fire may be
caused.

Indicates a mandatory action that cannot be specifically identified. Make sure to
follow the instruction.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

CE Statement

Warning: This is a Class A product. In domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures (EN55022).

BSMI Statement

Trademarks

NEC ESMPRO and NEC EXPRESSBUILDER are trademarks of NEC Corporation.
Microsoft, Windows, Windows Server, Windows NT, and MS-DOS are registered trademarks or
trademarks of Microsoft Corporation in the United States and other countries.
Intel and Pentium are registered trademarks of Intel Corporation.
LSI-Logic, MegaRAID, and Power Console Plus are registered trademarks or trademarks of LSI
Logic Corp.
Datalight is a registered trademark of Datalight, Inc.
ROM-DOS is a trademark of Datalight, Inc.
Novell and NetWare are registered trademarks of Novell, Inc. of the United States.
AT is a registered trademark of International Business Machines Corporation in the United States
and other countries.
Adobe, Adobe logo, and Acrobat are trademarks of Adobe Systems Incorporated.
DLT and DLTtape are trademarks of Quantum Corporation of the United States.
All other product, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective trademark owners.

Windows XP stands for Microsoft® Windows® XP Professional operating system and Microsoft®
Windows® XP Home Edition operating system. Windows 2000 stands for Microsoft® Windows

®

2000 Server operating system and Microsoft® Windows® 2000 Advanced Server operating system,
and Microsoft® Windows® 2000 Professional operating system. Windows 2003 stands for
Microsoft® Windows Server 2003 Server operating system and Microsoft® Windows Server

2003 Standard Edition and Enterprise Edition. Windows Me stands for Microsoft® Windows

®

Millennium Edition Operating System. Windows 98 stands for Microsoft® Windows®98 operating
system. Windows 95 stands for Microsoft® Windows®95 operating system.

Momentary voltage drop prevention:

This product may be affected by a momentary voltage drop caused by lightning. To prevent a
momentary voltage drop, an AC uninterruptible power supply (UPS) unit should be used.

Notes:

(1) No part of this manual may be reproduced in any form without the prior written permission of

NEC Corporation.

(2) The contents of this manual may be revised without prior notice.

(3) The contents of this manual shall not be copied or altered without the prior written permission

of NEC Corporation.

(4) All efforts have been made to ensure the accuracy of all information in this manual. If you

notice any part unclear, incorrect, or omitted in this manual, contact the sales agent where you
purchased this product.

(5) NEC assumes no liability arising from the use of this product, nor any liability for incidental or

consequential damages arising from the use of this manual regardless of Item (4).

i

PREFACE

Congratulations on the purchase of your NEC Express server.

Purchase of this server is your assurance of receiving state-of-the-art, high quality hardware to meet
your needs, both now and in the future.

Read this User's Guide thoroughly to fully understand handling of the NEC Express server and
appreciate its functions to the maximum extent.

ii

ABOUT THIS USER'S GUIDE

This manual is a guide for proper setup and use of your server.
This manual also covers useful procedures for dealing with difficulties and problems that may arise
during setup or operation of your server.
Keep this manual for future use.
The following describes how to proceed with this manual.

How to Use This Manual

To aid you in finding information quickly, this manual contains the following information:

Chapter 1 Notes on Using Your Server

includes information that needs attention to use the server. Make sure to read this chapter
before setting up and using the server. It also includes requirements and advisory information
for transfer and disposal of the server.

Chapter 2 General Description

includes information necessary to use the server, such as names and functions of its
components, handling of the floppy disk and CD-ROM drives.

Chapter 3 Setting Up Your Server

tells you how to select a site, unpack the system, make cable connections, and power on your
system.

Chapter 4 Configuring Your Server

tells you how to configure the system and provides instructions for running the BIOS Setup Utility.
This chapter also provides information on mother board jumper settings.

Chapter 5 Installing the Operating System with Express Setup

describes how to install the operating system.

Chapter 6 Installing and Using Utilities

describes how to install the utilities for the server. It also includes a description on using the
attached "NEC EXPRESSBUILDER" CD-ROM.

Chapter 7 Maintenance

provides you with all the information necessary to maintain successful operation of the server.
This chapter also includes a description on relocating and storing the server.

Chapter 8 Troubleshooting

contains helpful information for solving problems that might occur with your system.

Chapter 9 Upgrading Your Server

provides you with instructions for upgrading your system with an additional processor, optional
memory, optional add-in cards, hard disk drives, peripheral devices, and power supply.

Chapter 10 Internal Cabling Diagram

includes cabling information for the three onboard IDE controller, the optional RAID controller,
and the power supply.

Appendix A Specification

provides specifications for your server.

Appendix B Other Precautions

provides supplementary notes on using the server.

iii

Appendix C IRQ and I/O Port Address

provides a list of factory-set IRQs and I/O port addresses assigned.

Appendix D Installing Windows Server 2003

describes how to install Microsoft Windows Server 2003 without using Express Setup. Using
the Express Setup tool is recommended for installing Windows Server 2003. See Chapter 5 for
details.

Appendix E Installing Windows 2000

describes how to install Microsoft Windows 2000 without using Express Setup. Using the
Express Setup tool is recommended for installing Windows 2000. See Chapter 5 for details.

Appendix F Product Configuration Record Table

provides a table to be filled with your server configuration.

Text Conventions

The following conventions are used throughout this manual. For safety symbols, see "SAFETY
INDICATIONS" provided earlier.

IMPORTANT:

Items that are mandatory or require attention when using the server

NOTE:

Helpful and convenient piece of information

IN THE PACKAGE

The carton contains various accessories, as well as the server itself. See the packing list to make
sure that you have everything and that individual components are not damaged. If you find any
component missing or damaged, contact your sales agent.

 Store the provided accessories in a designated place for your convenience. You will need

them to install an optional device or troubleshoot your server, as well as to set it up.

 Make a backup copy of each provided floppy disk, if any. Store the original disk as the

master disk in a designated place, and use its copy.

 Improper use of any provided floppy disk or CD-ROM may alter your system

environment. If you find anything unclear, immediately ask your sales agent for help.

iv

CONTENTS

Preface ..............................................................................................................................................i

About This User's Guide..................................................................................................................ii

In the Package.................................................................................................................................iii

Chapter 1 Notes on Using Your Server........................................................................ 1-1

Warning Labels.............................................................................................................................1-2

Safety Notes..................................................................................................................................1-3

General .....................................................................................................................................1-3

Power Supply and Power Cord Use .........................................................................................1-4

Installation, Relocation, Storage, and Connection....................................................................1-5

Cleaning and Working with Internal Devices...........................................................................1-6

During Operation .....................................................................................................................1-7

For Proper Operation....................................................................................................................1-8

Transfer to Third Party .................................................................................................................1-9

Disposal and Consumables.........................................................................................................1-10

User Support...............................................................................................................................1-11

Chapter 2 General Description ..................................................................................... 2-1

Overview ......................................................................................................................................2-2

System Chassis .............................................................................................................................2-3

Front View................................................................................................................................2-3

Rear View.................................................................................................................................2-5

Internal View ............................................................................................................................2-7

Mother Board................................................................................................................................2-8

Standard Features .........................................................................................................................2-9

Power Supply .........................................................................................................................2-10

Peripheral Bays ......................................................................................................................2-10

Remote Power-On Feature (Wake On LAN)..........................................................................2-10

AC LINK Feature...................................................................................................................2-11

Security ..................................................................................................................................2-11

NEC EXPRESSBUILDER ....................................................................................................2-11

NEC ESMPRO.......................................................................................................................2-12

Off-line Maintenance Utility..................................................................................................2-12

System Diagnostic Utility ......................................................................................................2-12

Using Your Server.......................................................................................................................2-13

POWER Switch......................................................................................................................2-13

SLEEP Switch........................................................................................................................2-17

Floppy Disk Drive..................................................................................................................2-18

CD-ROM Drive......................................................................................................................2-20

v

Chapter 3 Setting Up Your Server ................................................................................ 3-1

Setup Flow....................................................................................................................................3-2

UNPACKING THE SYSTEM......................................................................................................3-3

Installing Optional Devices ..........................................................................................................3-3

Selecting Server Site.....................................................................................................................3-4

Connecting Peripheral Devices.....................................................................................................3-6

Connecting Power Cord................................................................................................................3-8

Turning On the Server ................................................................................................................3-10

Installing Operating System .......................................................................................................3-12

Installing Utilities .......................................................................................................................3-12

Making Backup Copies of System Information..........................................................................3-12

Chapter 4 Configuring Your Server.............................................................................. 4-1

System BIOS (BIOS Setup Utility) ..............................................................................................4-2

Starting SETUP Utility.............................................................................................................4-3

Description on On-Screen Items and Key Usage.....................................................................4-4

Configuration Examples...........................................................................................................4-5

Menu and Parameter Descriptions ...........................................................................................4-9

Add-in Card's BIOS....................................................................................................................4-28

Configuring Mother Board Jumpers...........................................................................................4-29

RAID Configuration Utility........................................................................................................4-31

Installing the Hard Disk Drives..............................................................................................4-31

Activating the SATA RAID Feature .......................................................................................4-31

Running the Array Configuration Utility (ACU) ...................................................................4-32

Using the Array Configuration Utility....................................................................................4-33

Chapter 5 Installing the Operating System with Express Setup ............................... 5-1

About Express Setup ....................................................................................................................5-2

Microsoft Windows Server 2003..................................................................................................5-4

Installation Notice ....................................................................................................................5-4

The Flow of Setup....................................................................................................................5-7

Installing and Setting Device Drivers.....................................................................................5-12

Setting for Solving Problems .................................................................................................5-17

Installing Maintenance Utilities .............................................................................................5-20

Updating the System ..............................................................................................................5-21

Making Backup Copies of System Information .....................................................................5-21

Exceptional Setup...................................................................................................................5-22

Microsoft Windows 2000 ...........................................................................................................5-23

Installation Notice ..................................................................................................................5-23

The Flow of Setup..................................................................................................................5-26

Installing and Setting Device Drivers.....................................................................................5-31

Setting for Solving Problems .................................................................................................5-35

Installing Maintenance Utilities .............................................................................................5-38

Updating the System - Installing Service Pack -....................................................................5-39

Making Backup Copies of System Information .....................................................................5-39

Exceptional Setup...................................................................................................................5-40

vi

HostRAID...................................................................................................................................5-41

Overview of HostRAID .........................................................................................................5-41

Notes ......................................................................................................................................5-42

HostRAID Setup Flow ...........................................................................................................5-43

Chapter 6 Installing and Using Utilities ....................................................................... 6-1

NEC EXPRESSBUILDER...........................................................................................................6-2

NEC EXPRESSBUILDER for DOS-Based with Local Console.............................................6-4

NEC EXPRESSBUILDER for Windows-Based (Master Control Menu)................................6-9

Configuration Diskette Creator...................................................................................................6-10

NEC ESMPRO ...........................................................................................................................6-13

Functions and Features...........................................................................................................6-13

Adaptec Storage Manager - Browser Edition..........................................................................6-14

Promise Array Management .......................................................................................................6-15

Power Console Plus....................................................................................................................6-16

Major Functions .....................................................................................................................6-16

Components............................................................................................................................6-16

Server Setup ...........................................................................................................................6-18

Management PC Setup...........................................................................................................6-19

Chapter 7 Maintenance.................................................................................................. 7-1

Making Backup Copies ................................................................................................................7-1

Cleaning........................................................................................................................................7-2

Cleaning the Server ..................................................................................................................7-3

Cleaning the Interior.................................................................................................................7-4

Cleaning the Keyboard/Mouse.................................................................................................7-5

Cleaning CD-ROM ..................................................................................................................7-6

System Diagnostics.......................................................................................................................7-7

Test Items .................................................................................................................................7-7

Starting and Ending the System Diagnostics............................................................................7-8

Relocating/Storing The Server....................................................................................................7-11

Chapter 8 Troubleshooting ........................................................................................... 8-1

System Viewers ............................................................................................................................8-2

Lamps ...........................................................................................................................................8-3

POWER/SLEEP Lamp.............................................................................................................8-4

DISK ACCESS Lamp ..............................................................................................................8-4

Access Lamps...........................................................................................................................8-4

LINK/ACT Lamp.....................................................................................................................8-4

1000/100/10 Lamp ...................................................................................................................8-5

Hard Disk Drive Lamp (DISK Lamp)......................................................................................8-5

Error Messages .............................................................................................................................8-7

Error Messages after Power-on................................................................................................8-7

POST Error Messages ..............................................................................................................8-8

Beep Codes.............................................................................................................................8-10

vii

Solving Problems........................................................................................................................8-11

Problems with NEC Express Server.......................................................................................8-11

Problems with Windows Server 2003 ....................................................................................8-15

Problems with Windows Server 2003 and Windows 2000.....................................................8-15

Problems with NEC EXPRESSBUILDER ............................................................................8-18

Problems with Express Setup.................................................................................................8-19

Problems with Disk Array Configuration...............................................................................8-21

Problems with Master Control Menu .....................................................................................8-22

Collecting Event Log .............................................................................................................8-22

Collect Configuration Information.........................................................................................8-23

Collecting Dr. Watson Diagnostic Information ......................................................................8-24

Memory Dump.......................................................................................................................8-24

Recovery for Windows 2000 System..........................................................................................8-25

Off-line Maintenance Utility ......................................................................................................8-28

Starting the Off-line Maintenance Utility...............................................................................8-28

Features of Off-line Maintenance Utility ...............................................................................8-29

Resetting the Server....................................................................................................................8-30

Forced Shutdown........................................................................................................................8-30

Chapter 9 Upgrading Your Server ................................................................................ 9-1

Safety Notes..................................................................................................................................9-2

Static Precautions .........................................................................................................................9-3

Preparing for Installation and Removal........................................................................................9-4

Installation or Removal Procedure ...............................................................................................9-5

Side Cover................................................................................................................................9-5

Front Mask ...............................................................................................................................9-9

3.5-inch Hard Disk Drive.......................................................................................................9-11

PCI Board...............................................................................................................................9-19

DIMM ....................................................................................................................................9-30

File Device .............................................................................................................................9-34

5-inch File Device Bay...........................................................................................................9-40

Hot-swap SCSI Hard Disk Drive Cage ..................................................................................9-46

Chapter 10 Internal Cabling Diagrams....................................................................... 10-1

Interface Cables ..........................................................................................................................10-2

Addition of Hard Disk............................................................................................................10-2

Connection of Disk Array Controller (SATA) ........................................................................10-4

Connection of Disk Array Controller (SCSI) .........................................................................10-6

Connection of 5.25-inch Device.............................................................................................10-8

Power Cables ............................................................................................................................10-13

viii

Appendix A Specifications............................................................................................A-1

Appendix B Other Precautions.....................................................................................B-1

Transfer Rate of the On-board LAN Controller ......................................................................B-1

Server Management Software .................................................................................................B-1

Floppy Disk............................................................................................................................. B-1

CD-ROM................................................................................................................................. B-4

Tape Media.............................................................................................................................. B-4

Keyboard................................................................................................................................. B-5

Mouse...................................................................................................................................... B-6

Appendix C IRQ and I/O Port Address.........................................................................C-1

Appendix D Installing Windows Server 2003 ..............................................................D-1

Before Installing Windows Server 2003 ......................................................................................D-1

Optional Board Supported by NEC EXPRESSBUILDER......................................................D-1

Installing Service Pack ............................................................................................................ D-1

Updating System .....................................................................................................................D-1

Re-installing to the Hard Disk which has been upgraded to Dynamic Disk ...........................D-2

Manual Installation when N8103-65F/80F Keeps Connection ...............................................D-2

MO Device.............................................................................................................................. D-2

Media such as DAT .................................................................................................................D-2

Partition Size ...........................................................................................................................D-3

Installing Windows Server 2003..................................................................................................D-4

Creating "Windows Server 2003 OEM-DISK for NEC EXPRESSBUILDER" .....................D-4

Windows Server 2003 Clean Installation ................................................................................ D-6

Upgrade Installation ................................................................................................................D-8

Reinstallation to Multiple Logical Drives .............................................................................D-10

Updating the System .............................................................................................................D-12

Driver Installation and Advanced Settings ................................................................................D-13

PROSet..................................................................................................................................D-13

Network Driver .....................................................................................................................D-14

Re-install the Network Driver ...............................................................................................D-15

Graphics Accelerator Driver..................................................................................................D-15

Installing SCSI Controller Driver..........................................................................................D-16

Setting for Collecting Memory Dump (Debug Information)..................................................D-16

ix

Appendix E Installing Windows 2000 .......................................................................... E-1

Before Installing Windows 2000 ................................................................................................. E-1

Optional Board Supported by NEC EXPRESSBUILDER...................................................... E-1

Installing Service Pack ............................................................................................................ E-1

Updating System ..................................................................................................................... E-1

Re-installing to the Hard Disk which has been upgraded to Dynamic Disk ........................... E-2

MO Device.............................................................................................................................. E-2

Media such as DAT ................................................................................................................. E-2

Partition Size ........................................................................................................................... E-3

Installing Windows 2000............................................................................................................. E-4

Creating "Windows 2000 OEM-DISK for NEC EXPRESSBUILDER"................................. E-4

Windows 2000 Clean Installation............................................................................................ E-6

Reinstallation to Multiple Logical Drives ............................................................................... E-7

Updating the System - Installing Service Pack -..................................................................... E-9

Driver Installation and Advanced Settings ................................................................................ E-10

PROSet.................................................................................................................................. E-10

Network Driver ..................................................................................................................... E-11

Re-install the Network Driver ............................................................................................... E-12

Graphics Accelerator Driver.................................................................................................. E-13

USB 2.0 Driver...................................................................................................................... E-13

Installing SCSI Controller Driver.......................................................................................... E-14

Setting for Collecting Memory Dump (Debug Information).................................................. E-14

Appendix F Product Configuration Record Table ...................................................... F-1

Hardware................................................................................................................................. F-1

Software .................................................................................................................................. F-3

x

(This page is intentionally left blank.)

Chapter 1

Notes on Using Your Server

This chapter includes information necessary for proper and safe operation of your server.

1-2 Notes on Using Your Server

WARNING LABELS

The warning label is attached to components with possible danger or their vicinity in your server to
inform the user that a hazardous situation may arise when operating the server. (Do not
intentionally remove or damage any of the labels.)

If you find any labels totally/partially removed or illegible due to damage, contact your sales
representative.

Notes on Using Your Server 1-3

SAFETY NOTES

This section provides notes on using your server safely. Read this section carefully to ensure
proper and safe use of the server. For symbols, see "SAFETY INDICATIONS" provided earlier.

General

WARNING

Do not use the server for services where critical high availability may directly
affect human lives.

Your server is not intended to be used with or control facilities or devices
concerning human lives, including medical devices, nuclear facilities and
devices, aeronautics and space devices, transportation facilities and devices;
and facilities and devices requiring high reliability. NEC assumes no liability for
any accident resulting in personal injury, death, or property damage if the server
has been used in the above conditions.

Do not use the server if any smoke, odor, or noise is present.

If smoke, odor, or noise is present, immediately turn off the server and
disconnect the power plug from the outlet, then contact your sales agent.
Using the server in such conditions may cause a fire.

Keep needles or metal objects away from the server.

Do not insert needles or metal objects into ventilation holes in the server or
openings in the floppy disk or CD-ROM drive. Doing so may cause an electric
shock.

CAUTION

Keep water or foreign matter away from the server.

Do not let any form of liquid (water etc.) or foreign matter (e.g., pins or paper
clips) enter the server. Failure to follow this warning may cause an electric
shock, a fire, or a failure of the server. When such things accidentally enter the
server, immediately turn off the power and disconnect the power plug from the
outlet. Do not disassemble the server. Contact your sales agent.

1-4 Notes on Using Your Server

Power Supply and Power Cord Use

WARNING

Do not hold the power plug with a wet hand.

Do not disconnect/connect the plug while your hands are wet. Failure to follow
this warning may cause an electric shock.

CAUTION

Plug in to a proper power source.

Use a proper wall outlet. Use of an improper power source may cause a fire or
a power leak.
Do not install the server where you need an extension cord. Use of a cord that
does not meet the power specifications of your server may heat up the cord and
cause a fire.

Do not connect the power cord to an outlet that has an illegal number of
connections.

The electric current exceeding the rated flow overheats the outlet, which may
cause a fire.

Do not pull the cable when disconnecting it.

When disconnecting the cable from the device, hold the cable connector and
pull it straight out. Pulling the cable out by the cable portion or giving mechanical
stress to the connector could damage the cables and connectors to result in an
electrical shock hazard or a fire.

Insert the power plug into the outlet as far as it goes.

Heat generation resulting from a halfway inserted power plug (imperfect contact)
may cause a fire. Heat will also be generated if condensation is formed on
dusty blades of the halfway inserted plug, increasing the possibility of fire.

Use the authorized power cord only.

Use only the power cord that comes with your server. Use of an unauthorized
power cord may cause a fire when the electric current exceeds the rated flow.
Also, observe the following to prevent an electric shock or fire caused by a
damaged cord.

 Do not stretch the cord harness.
 Do not pinch the power cord.
 Do not bend the power cord.
 Keep chemicals away from the power cord.
 Do not twist the power cord.
 Do not place any object on the power cord.
 Do not bundle power cords.
 Do not alter, modify, or repair the power cord.
 Do not secure the power cord with staples or equivalents.
 Do not use any damaged power cord. (Replace a damaged power cord with

a new one of the same specifications. Ask your sales agent for
replacement.)

Notes on Using Your Server 1-5

Installation, Relocation, Storage, and Connection

WARNING

Disconnect the power cord(s) before installing or removing the server.

Make sure to power off the server and disconnect the power cord(s) from a
power outlet before installing/removing the server. All voltage is removed only
when the power cords are unplugged.

CAUTION

Never attempt to lift the server only by yourself.

Your server weighs max 20 kg (depending on its hardware configuration).
Carrying the server only by yourself may strain your back. Hold the server firmly
by its bottom with at least two or more people. Do not hold the front mask to lift
the server. The front mask may be disengaged from the server, causing
personal injury.

Do not install the server in any place other than specified.

Do not install the server in the following places or any place other than specified
in this manual. Failure to follow this instruction may cause a fire.

 a dusty place
 a humid place such as near a boiler
 a place exposed to direct sunlight
 an unstable place

Do not connect any interface cable with the power cord of the server plugged to
a power source.

Make sure to power off the server and unplug the power cord from a power
outlet before installing/removing any optional internal device or
connecting/disconnecting any interface cable to/from the server. If the server
is off-powered but its power cord is plugged to a power source, touching an
internal device, cable, or connector may cause an electric shock or a fire
resulted from a short circuit.

Do not use any unauthorized interface cable.

Use only interface cables provided by NEC and locate a proper device and
connector before connecting a cable. Using an authorized cable or connecting
a cable to an improper destination may cause a short circuit, resulting in a fire.
Also, observe the following notes on using and connecting an interface cable.

 Do not use any damaged cable connector.
 Do not step on the cable.
 Do not place any object on the cable.
 Do not use the server with loose cable connections.

1-6 Notes on Using Your Server

Cleaning and Working with Internal Devices

WARNING

Do not disassemble, repair, or alter the server.

Never attempt to disassemble, repair, or alter the server on any occasion other
than described in this manual. Failure to follow this instruction may cause an
electric shock or fire as well as malfunctions of the server.

Do not look into the CD-ROM drive.

A laser beam used in the CD-ROM drive is harmful to the eyes. Do not look
into or insert a mirror into the drive while the drive is powered. If a laser beam
is caught in your eyes, you may lose your eyesight (the laser beam is invisible).

Do not remove the lithium battery.

Your server contains the lithium battery. Do not remove the battery. Placing
the lithium close to a fire or in the water may cause an explosion.

When the server does not operate appropriately due to the dead lithium battery,
contact your sales agent. Do not disassemble the server to replace or
recharge the battery by yourself.

Disconnect the power plug before accessing inside the server, or connecting the
peripherals.

Make sure to power off the server and disconnect the power plug from a power
outlet before cleaning or installing/removing internal optional devices.
Touching any internal device of the server with its power cord connected to a
power source may cause an electric shock even of the server is off-powered.

Disconnect the power plug from the outlet occasionally and clean the plug with a
dry cloth. Heat will be generated if condensation is formed on a dusty plug,
which may cause a fire.

CAUTION

Avoid installation in extreme temperature conditions.

Immediately after the server is powered off, its internal components such as
hard disks are very hot. Leave the server until its internal components fully
cool down before installing/removing any component.

Make sure to complete board installation.

Always install a board firmly. An incompletely installed board may cause a
contact failure, resulting in smoking or fire.

Protect the unused connectors with the protective cap.

The unused power supply cable connectors are covered with the protective cap
to prevent short circuits and electrical hazards, when removing the power supply
cable connector from the install devices, attach the protective cap to the
connector. Failure to follow this warning may cause a fire or an electric shock.

Notes on Using Your Server 1-7

During Operation

CAUTION

Stay away from the fan.

Keep your hand or hair away from the cooling fan on the rear of the server.
Failure to follow this warning may get your hand or hair caught in the fan,
resulting in injury.

Avoid contact with the server during thunderstorms.

Disconnect the power plug from the outlet when a thunderstorm is approaching.
If it starts thundering before you disconnect the power plug, do not touch any
part of the server including the cables. Failure to follow this warning may cause
a fire or an electric shock.

Keep animals away from the server.

Failure to follow this warning may cause a fire or an electric shock.

Do not leave the CD tray open.

If dust gets on the lens of CD-ROM drive, the drive may have problems reading
your disks.
Also, the CD tray may be broken by contacting any objects.

Take off the headset before connection.

To protect your ears, take off the headset before connecting it to the headset
jack. Make sure that the volume is not extremely turned up before connection.

Do not place any object on top of the server.

The server may fall and cause property damage to the surroundings.

Do not use a cellular phone or pager around the server.

Turn off the cellular phone or pager. Radio interference may cause
malfunctions of the server.

1-8 Notes on Using Your Server

FOR PROPER OPERATION

Observe the following notes for successful operation of the server. Use of the server ignoring the
notes will cause malfunctions or failures of the server.

 Install the server in a place that meets requirements for successful operation. For details,

see Chapter 3, "Setting Up Your Server."

 If the power cord supplied with your system is not compatible with the AC wall outlet in

your region, contact your service representative to obtain a suitable power cord.

 Make sure to power off the server before connecting or disconnecting cables between the

server and peripheral devices.

 Verify that the access lamp on the server is unlit before turning off the server or ejecting

the floppy disk.

 When plugging the power cord to the system, you may experience 10 seconds delay from

the time you press the POWER/SLEEP switch on the front panel. This is normal system
operation.

 When you have just turned off the server, wait at least 10 seconds before turning it back

on. If the server is connected to the UPS, set at least 10 seconds delay in the power-on
schedule.

 For the disk which does not conform to the CD standard, the playback of such a disk with

the CD drive is not guaranteed.

 Turn off the power and unplug the power cord from the outlet before relocating the server.

 Clean the server on a regular basis. (See Chapter 7 for cleaning.) Regular cleaning

proactively prevents various failures of the server.

 Lightning may cause a momentary voltage drop. To prevent this problem, it is

recommended to use of an uninterruptible power supply unit.

 Make sure to use optional devices supported by the server. Some non-supported devices

may be physically installed/connected but cause failures of the server as well as
malfunctions of the server.

 NEC recommends you use NEC's genuine products. Some third-party products claim

that they support the server. However, repair of the server due to a failure or damage
resulted from use of such third-party products will be charged.

Notes on Using Your Server 1-9

TRANSFER TO THIRD PARTY

The following must be observed when you transfer (or sell) the server or software provided with the
server to a third party:

Make sure to provide this manual along with the server to a third party.

IMPORTANT: About data on the hard disk

Be sure to take appropriate measures not to leak important data (e.g.,
customers' information or companies' management information) on the
removed hard disk to any third parties.

Data seems to be erased when you empty "Recycle Bin" of Windows or
execute the "format" command of the operating system. However, the
actual data remains written on the hard disk. Data not erased completely
may be restored by special software and used for unexpected purposes.

It is strongly recommended that the software or service (both available
at stores) for data erasure should be used in order to avoid the trouble
explained above. For details on data erasure, ask your sales
representative.

Provided software

To transfer or sell any software application that comes with the server to a third party, the following
requirements must be satisfied:

 All provided software applications must be transferred and no backup copies must be

retained.

 Transfer requirements listed in "Software License Agreement" that comes with each

software application must be satisfied.

 Software applications that are not approved for transfer must be uninstalled before

transferring the server.

1-10 Notes on Using Your Server

DISPOSAL AND CONSUMABLES

 Dispose of the server, all the internal devices, floppy disks, and CD-ROMs according to

all national laws and regulations.

IMPORTANT:

 For disposal (or replacement) of the battery on the mother board of

the server, consult with your sales agent.

 It is the user's responsibility to completely erase or modify all the

data stored in storage device such as hard disk so that the data
cannot be restored.

 Your server contains some components that are only good for a limited period of time and

require replacement, such as fans, internal batteries, the internal CD-ROM drive, the
floppy disk drive, and the mouse. For stable operation of the server, NEC recommends
you replace these components on a regular basis. Consult with your sales agent for
replacement or the product lives.

WARNING

Do not remove the lithium battery.

Your server contains the lithium battery. Do not remove the battery. Placing
the lithium or nickel cadmium battery close to a fire or in the water may cause an
explosion.

When the server does not operate appropriately due to the dead lithium battery,
contact your sales agent. Do not disassemble the server to replace or recharge
the battery by yourself.

Mother board

Notes on Using Your Server 1-11

USER SUPPORT

Before Asking for Repair, do the following when the server appears to fail:

1. Check if the power cord and the cables to other devices are properly connected.

2. See Chapter 8 to find if your problem fits the description. If it does, take the

recommended measure for it.

3. Check if the software required for operation of the server is properly installed.

If the server still appears to fail after you have taken the above actions, consult with your sales agent
immediately. Take notes on lamp indications of the server and alarm indications on the display
unit before consultation, which may provide a significant help to your sale agent.

1-12 Notes on Using Your Server

Advice for Health

The longer you keep using the computer equipment, the more you become
tired, which may cause disorders of your body. When you use a
computer, observe the following to keep yourself from getting tired:

Good Working Posture

You have good posture if the following are satisfied when you use a
computer:

• You sit on a chair with your back straight.

• Your hands are parallel with the floor when you put them on the

keyboard.

• You look at the screen slightly lower than your eye height.

You have "good working posture" as described in the above when no part
of your body is under excess strain, in other words when your muscles are
most relaxed.

You have "bad posture" when you sit with your back hunched up or you
operate a display unit with your face close to the screen. Bad working
posture may cause eye strain or poor eyesight.

Adjustment of Display Unit Angles

Most display units are designed for adjustment of the horizontal and
vertical angles. This adjustment is important to prevent the screen from
reflecting bright lights and to make the display contents easy to see. You
will not be able to keep "good working posture" and you will feel more tired
than you should if you operate a display unit without adjusting horizontal
and vertical angles.

Adjustment of Screen Brightness and Contrast

The display unit has brightness and contrast adjustment functions. The
most suitable brightness and contrast depend on the individual and the
working environment (well-lighted room or insufficient light). Adjust
brightness and contrast so that the screen will be easy to see. An
extremely bright or dark screen will give a bad effect to your eyes.

Adjustment of Keyboard Angle

The keyboard provided with the server is designed for adjustment of an
angle. Adjust the keyboard angle at which the keyboard is easy to
operate. The adjustment assists in reducing strain on your shoulders,
arms, and fingers.

Cleaning of Equipment

Clean equipment regularly. It is difficult to see the display contents on a
dusty screen. Keeping equipment clean is also important for your sight.

Fatigue and Rest

If you feel tired, you should stop working and do light exercises.

Chapter 2

General Description

This chapter provides information that you should be familiar with before using the server. It
includes names and functions of the components and features of the server.

2-2 General Description

OVERVIEW

Your server is a modular, multiprocessing server based on the Intel® Pentium® 4 microprocessor
family. It is a solid performer and offers the latest technology. The combination of compute
performance, memory capacity, and integrated I/O provides a high performance environment for
many server market applications. These range from large corporations supporting remote offices to
small companies looking to obtain basic connectivity capability such a file and print services, e-mail,
web access, web site server, etc. Your server is housed and available as a tower-based system.

Front View

As application requirements increase, you can expand your server with an additional memory, add­in boards and peripheral devices; tape devices, CD-ROM, and hard disk drives. The server features
the following major components.

 A high-performance Intel Pentium 4 processor

 Up to 4GB of memory (using 1GB DIMMs)

Minimum configuration is 256MB of memory

 Dual channel memory configuration

 Five integrated I/O expansion PCI-X/PCI slots for add-in boards (one PCI Express slot,

two 64-bit/100 MHz and two 32-bit/33 MHz slots)

 Onboard enhanced IDE interface controller

 Onboard enhanced serial ATA RAID controller

 Onboard 1000/100/10 network controller

 Integrated CD-ROM and 1.44MB diskette drives

 Three hard disks expansion bays

 One removable media expansion bay

 Embedded PC-compatible support (serial, parallel, mouse, keyboard, USB, LAN, and

video)

 High degree of SATA hard disk drive fault tolerance and advanced disk array management

features through the use of RAID Technology.

General Description 2-3

SYSTEM CHASSIS

Names and functions of the components are shown below.

Front View

1

2

3

4

5

6

7

8

9

4

2

A

dditional

slot 1

A

dditional

slot 2

With optional 5-inch file device

bay installed

2-4 General Description

1 File bay

The file bay contains both a 5.25-inch device bay and a 3.5-inch device bay.

2 CD-ROM drive

The CD-ROM drive reads data from the inserted CD-ROM.
Each drive is equipped with the following:

• Tray Eject button to eject the tray

• Access lamp that indicates the disk access status

• Emergency hole to forcibly eject the tray

3 5.25-inch device bay

Backup file device may be installed in the 5.25-inch device bay.
The server can include a maximum of two devices.
A CD-ROM drive is installed on the top of bay.

4 3.5-inch floppy disk drive

Reads/writes data from/to the 3.5-inch floppy disk inserted.
The floppy disk drive is equipped with the following:

• Eject button to eject the floppy disk

• Access lamp that indicates the floppy disk access status

5 Disk access lamp (green)

The disk access lamp is lit while the system accesses to a built-in hard disk. If the built-in hard
disk is connected to the proper optional board, this lamp can be lit only when the LED cable
provided with the system is connected.

6 POWER/SLEEP lamp (green)

Lights in green when the server is powered on. Blinks when the system is placed in the sleep
mode.

7 POWER/SLEEP switch

The POWER/SLEEP switch is used to turn the power of the server ON/OFF. If you press this
switch once, the power is turned on with the lamp going on green. If you press the switch
again, the power is turned off.

Some OS setting can provide the function of switching to the power saving (sleep) mode. If
you press the POWER/SLEEP switch once after the setting, the system is entered into the
power saving mode. If you press the switch again, the system is returned to the normal state.
(Depending on installed optional boards, the function cannot be provided.)

8 Front mask

The front mask protects the front face of the chassis.

9 Release tabs (3 at an end of front mask)

The release tabs are provided to release the lock of the front mask. Press the tabs to remove
the front mask.

General Description 2-5

Rear View

1

2

3

2

45

6

7

8

9

10

11

12

2-6 General Description

1 AC inlet

The AC inlet is connected with the power cord.

2 Fixing screws

Secures the left side cover.

3 Cover lock plate

Installing a theft prevention device
protects the internal components of the
workstation from being stolen.

4 Mouse connector

The mouse connector is connected with the mouse coming with the server.

5 Keyboard connector

The keyboard connector is connected with keyboard coming with the server.

6 USB connectors

The USB connectors are connected with devices accepting the USB interface.

7 Serial port connector

The serial port connector is used to connect the server to a device with the serial interface.
The server cannot be directly connected to a leased line through the connector.

8 Printer port connector

The printer port connector is connected with a printer with the Centronics interface.

9 Monitor connector

The monitor connector is connected with the display unit.

10 LAN connector

The LAN connector is connected with a network system on LAN (1000BASE-T/100BASE­TX/10BASE-T). The value following the bold-faced number indicates the port number.

11 1000/100/10 lamp

1000/100/10 lamp indicates the LAN transfer rate.

12

Link/ACT lamp

The Link/ACT lamp shows the LAN access status.

General Description 2-7

Internal View

1 Power supply
2 Processor cooling fan (mounted on the processor)
3 DIMMs (factory-installed in slot #1.)
4 CD-ROM drive
5 File bay

A standard CD-ROM drive and floppy disk drive are installed. The device bay can include a
maximum of two 5.25-inch devices and one 3.5-inch device.

6 3.5-inch floppy disk drive (dotted line)
7 Device bay fixing screw

To remove the hard disk drive bay, loosen this screw. To remove the file bay, remove this screw.

8 Front cooling fan (dotted line)
9 PCI guide rail

10 Hard disk drive bay

Hard disk drive bay can be equipped with three hard disks.

11 Hard disk drive (optional)
12 Mother board
13 PCI board retention spring
14 Rear cooling fan

123 4

7

8

91011

13

14

6

12

5

2-8 General Description

MOTHER BOARD

1

Processor socket

12

Connector (not used in this system)

2

Power connectors

13

LED connector

3

DIMM sockets

14

PCI board slots

4

PCI boards cooling fan connector Slot 14-#1: PCI Express ×4

5

Configuration jumper switch (CMOS/Clear) Slot 14-#2 and #3: 64bit/100 MHz PCI-X

6

Front panel connector Slot 14-#4 and #5: 32bit/33 MHz PCI-X

7

Lithium battery

15

Rear cooling fan connector

8

Serial ATA connectors

16

Heat sink fan connector

9

Buzzer

17

Connector for external device

10

Floppy disk drive connector

11

Ultra ATA100 connector (for CD-ROM drive)

1 2

3-#4
3-#3
3-#2
3-#1

17

4

5

6
7

8-4

8-3

9

10

11

8-1 8-2

1213

14-1

14-2

14-3

14-4

14-5

15

16

General Description 2-9

STANDARD FEATURES

High performance Expandability

 Intel



Pentium 4 Processor

 High-speed 1000BASE-T/100BASE-

TX/10BASE-T interface
(1Gbps/100Mbps/10Mbps supported)

 Serial ATA 150
 Dual channel memory configuration

 Five integrated I/O expansion PCI-X slots

(one PCI Express, two 64-bit/100 MHz and
two 32-bit/33 MHz)

 Large memory of up to 4GB

(four 1GB DIMMs)

 Three hard disk drive bays
 USB interface (USB 2.0)

High-reliability Many Available Features

 El Torito Bootable CD-ROM (no emulation

mode) format support

 Remote power-on feature
 AC-LINK feature

Self-diagnosis

 Memory monitoring feature (single-bit

error correction/double-bit error detection)

 Temperature detection
 Cooling fan monitoring feature
 Internal voltage monitoring feature
 BIOS password feature
 Embedded serial ATA RAID drive

configuration feature

 Optional SCSI controllers

 Power On Self-Test (POST)
 Test and Diagnosis

Management Utilities Easy and Fine Setup

 NEC ESMPRO
 Off-line Maintenance Utility

 NEC EXPRESSBUILDER (system setup

utility)

 BIOS setup utility
 Serial ATA RAID configuration utility
 Configuration Diskette Creator

Power Saving Feature

 Sleep feature

(available for Windows Server 2003 /
Windows 2000)

2-10 General Description

Power Supply

The system contains one auto-sensing 380-watt power supply at an operating frequency of 50/60
Hz.

The power supply is designed to comply with existing emission standards and provide sufficient
power for a fully loaded system configuration.

Peripheral Bays

The system supports a variety of standard PC AT-compatible peripheral devices. The chassis
includes these peripheral bays:

 One 3.5-inch file bay for installing the standard 3.5-inch floppy disk drive (supports

720KB and 1.44MB floppy disk media) or an optional file device.

 Two 5.25-inch file bays for installing half-height 5.25-inch peripheral devices such as an

optional tape drives. (An ATAPI CD-ROM drive is factory-installed.)

 The hard disk drive bays for installing up to three ATA150 or SCSI hard disk drives.

NOTE: The optional peripheral device bay can include two 5.25-inch

file devices (or one hot-swap SCSI hard disk drive bay), one slim­height CD-ROM drive, and one 3.5-inch floppy disk drive.

Remote Power-On Feature (Wake On LAN)

The remote power-on function turns on the server through a network. It sends a special packet
from the management computer to a remote server to turn it on if the server is off-powered.

To enable this feature, you must select "Enabled" for each submenu in the Power Management
Setup of the Advanced menu of the BIOS setup utility, "SETUP." (See Chapter 4.)

The remote power-on feature is not available in the following cases. Press the POWER/SLEEP
switch once to start the OS, and turn off the server in an appropriate procedure.

 Abnormal previous system shut-down

 No power supply to the server (due to turned-off breaker, disconnected power cord, power

blackout, etc.)

General Description 2-11

AC LINK Feature

When the power cord of the server is connected to an uninterruptible power supply (UPS) unit, the
server supports the power linkage feature that enables control over the power supply from the UPS
to the server. The AC LINK feature can be enabled or disabled with Power Management Setup in
the Server menu of the BIOS setup utility, "SETUP." (See Chapter 4.)

Security

The BIOS setup utility provides a number of security features to prevent unauthorized or accidental
access to the system. Once the security measures are enabled, access to the system is allowed only
after the user enters the correct password(s). For example:

 Set and enable an administrative password.

 Set and enable a user password

 Check the user account when entering the BIOS setup utility or booting the system.

NEC EXPRESSBUILDER

The CD-ROM that comes with your server contains a setup utility called "NEC
EXPRESSBUILDER." When you have first installed the server or append features to the server,
use the NEC EXPRESSBUILDER to set up your server.

Refer to Chapter 6 for details.

IMPORTANT: Do not use the NEC EXPRESSBUILDER for any

other computers than the server, nor other NEC Express5800 series
servers than the one that NEC EXPRESBUILDER is provided for. Not
following this instruction may cause failures.

The major functions of the NEC EXPRESSBUILDER are:

 To install the OS.

It installs an operating system.

 To diagnose the system.

It diagnoses the server.

 To create a support disk.

It copies utilities in the NEC EXPRESSBUILDER CD-ROM into a floppy disk to launch
them from the floppy disk.

 To update the BIOS

It updates the BIOS features of the server.

2-12 General Description

 To update the Windows System*

It updates the several resources of Microsoft Windows Server 2003, Microsoft Windows

2000.

 To install the utilities*

It install the management utilities of NEC ESMPRO.

 To read the online documents*

It opens the online document files (".pdf" files).

* These functions are available under Windows system.

NEC ESMPRO

The NEC ESMPRO is server management software that runs on the OS. The NEC ESMPRO
includes the NEC ESMPRO Manager for the server monitoring terminal and the NEC ESMPRO
Agent for the NEC Express server.

NOTE: For details of major functions of the NEC ESMPRO, system

configuration and setups with the NEC ESMPRO, see Chapter 6.
Available functions of the NEC ESMPRO depend on the OS you install.
Ask your sales agent for details.

Off-line Maintenance Utility

The Off-line Maintenance Utility is used for proactive maintenance and fault analysis of the server.
Normally this utility is used by the maintenance engineer.

Refer to Chapter 8 for details.

System Diagnostic Utility

The system diagnostic utility contained in the NEC EXPRESSBUILDER is useful to prevent the
hardware failures. See Chapter 7 for details.

General Description 2-13

USING YOUR SERVER

This section describes basic operations of your server including how to use devices such as the
floppy disk drive and the CD-ROM drive. See Appendix B for notes on using the floppy disk, CD­ROM, and accessories including the keyboard and the mouse.

POWER Switch

Use the POWER/SLEEP switch to turn on/off the server.

Power On

Press the POWER switch on the front of the computer chassis.

The POWER/SLEEP lamp lights in green.

IMPORTANT:

 If the power cord is connected to a power control device such as a

UPS (Uninterruptible Power Supply), make sure that the power
control device is powered.

 Do not turn off the server until characters appear on the screen.

POWER/SLEEP lamp

2-14 General Description

POST

POST (Power On Self-Test) is the self-diagnostic program stored in the system memory.

When you power on the server, the system automatically runs POST to check the mother board,
ECC memory module, CPU module, keyboard, and mouse. POST also displays messages of the
CMOS Setup utility, such as the start-up message, while in progress.

With the factory setup of the server, the NEC logo appears on the display unit while POST is in
progress. (To display the POST check results, press Esc.)

NOTE: You can set the POST check results to appear on the display

unit without pressing Esc. To do so, select "Enabled" for "Boot-time
Diagnostic Screen" under the Advanced menu of the BIOS setup utility.

You don't always need to check the POST check results. Check messages that POST displays
when:

 you use the NEC Express server for the first time.

 the server appears to fail.

 the server beeps for many times between power-on and OS start-up.

 an error message appears on the display unit.

General Description 2-15

POST Execution Flow

The following describes the progress of POST in the chronological order.

IMPORTANT:

 Do not make key entries or perform mouse operations while POST

is in progress.

 Some system configurations may display the message "Press Any

Key" to prompt a key entry. This message is driven by BIOS of an
installed optional board. Make sure to read the manual that comes
with the optional board before any key entry.

 Powering on the server, after you installed or removed an optional

PCI board or moved it to another slot, may display the message that
indicates incorrect board configuration and suspend POST.
In such a case, press F1 to continue POST. Board configuration
can be made using the utility described later.

1. After a few seconds from power-on, POST starts checking the memory. The count

message of the basic and expansion memory appears at top left on the display unit screen.
The memory check may takes a few minutes to complete depending on the memory size
of the server. Also, it may take approximately one minute for the screen display to
appear after rebooting the server.

2. Some messages appear upon completion of the memory check. These messages appear

to indicate that the system has detected the CPU, keyboard, and mouse.

3. After a few seconds, POST displays the following message prompting you to launch the

BIOS setup utility, stored in the system memory of the server. This message appears at
bottom left on the screen.

Press <F2> to enter SETUP or Press <F12> LAN Boot

Launch the BIOS setup utility when you need to change the settings to meet the
requirements for the server. As long as the above message is not displayed with an error
message, you don't have to launch the utility. (Ignore the message. POST will
automatically proceed.)

To launch the BIOS setup utility, press F2 while the above message is displayed. See
Chapter 4 for setup and parameters.

2-16 General Description

NOTES:

 Depending on the installed memory capacity, the time taken to

accept F2 may be rather short. If so, press F2 just after the power­on of the server or after the NEC logo appears (Esc may not be
pressed).

 In some setting of the BIOS setup utility, the screen of prompting

the security password appears before the main menu if the password
is registered. There are two types of passwords, supervisor and user
passwords. If you log on to the system as a supervisor, you can not
only check all the settings but also change them by using the BIOS
setup utility. If you log on to the system as a user, you can only
check or change some settings limitedly.

The server automatically restarts POST all over again when you exit the BIOS setup
utility.

4. If your server uses onboard serial ATA (SATA) RAID feature, the following message is

displayed on the screen to prompt you to run Array Configuration Utility (ARC).

Press <Ctrl><A> for Adaptec RAID Configuration Utility

Press Ctrl + A to run ARC. For detail explanation, refer to Chapter 4.

5. If the server has an optional RAID controller or SCSI card, POST displays the message

prompting you to launch the RAID configuration utility and the disk array BIOS setup
utility.

Refer to the manual supplied with the disk array controller for detail instructions.

POST will automatically proceed a few seconds later.

6. If you set a password entry using the BIOS setup utility, the password entry screen

appears upon successful completion of POST.

IMPORTANT: Do not set a password before installing an OS.

7. The OS starts when POST completes.

General Description 2-17

POST Error Messages

When POST detects an error, it displays an error message on the display unit screen or emits beep
code. See Chapter 8 for POST error codes.

IMPORTANT: Take a note on the messages displayed before

consulting with your sales agent. Alarm messages are useful
information for maintenance.

Power Off

Follow the procedure below to power off the server. If the power cord of the server is connected to
a UPS, refer to the manual that comes with the UPS or the manual for the application that controls
the UPS.

IMPORTANT: Always allow POST to complete before turning off the
server.

1. Shut down the OS.

2. Press the POWER/SLEEP switch on the front of the server.

The POWER/SLEEP lamp goes out.

3. Power off peripheral devices.

SLEEP Switch

The POWER/SLEEP switch allows you to save almost all power of the server (power-saving mode
or sleep mode).

Press the POWER/SLEEP switch on the front of the server to place the server in the power-saving
mode. (The POWER/SLEEP lamp blinks.) In the power-saving mode, the server retains the
memory data and the status of the previous operations.

To resume the original state, press the POWER/SLEEP switch again. (It may take a little time to
resume the original state.)

NOTE: The operational level in the power-saving mode depends on

the OS in use. (Available for Windows Server 2003 and Windows

2000.)

2-18 General Description

Floppy Disk Drive

Your server is provided with the 3.5-inch floppy disk drive on its front to write/read data to/from a
floppy disk.

Your server supports the following 3.5-inch floppy disks:

 2HD floppy disk (double-sided high-density track type)

Stores data of 1.44MB.

 2DD floppy disk (double-sided double-density track type)

Store data of 720KB.

Make sure that the server is powered (the POWER/SLEEP lamp is lit) before inserting a floppy disk
into the floppy disk drive.

When you completely insert the floppy disk into the floppy disk drive, the drive clicks and the eject
button on the floppy disk is slightly pushed out.

NOTES:

 You cannot use a 1.2MB-formatted floppy disk to boot the system.

 When an unformatted floppy disk is inserted, the message notifying

that date read is not available and the message prompting formatting
are displayed. Refer to the manual that comes with the OS to
format the floppy disk.

 If the floppy disk contains a system, powering on or restarting the

server with the floppy disk inserted boots the system from the
floppy disk.

To eject the floppy disk from the floppy disk drive, press the eject button.

NOTE: Make sure that the floppy disk access lamp is unlit before

ejecting the floppy disk. Ejecting the disk when the access lamp is lit
may destroy the disk data.

General Description 2-19

NOTE: Use of the floppy disk

The floppy disk is an important data storage media with delicate
structure and requires care. Keep the following notes in mind to use
it:

 Insert the floppy disk into the floppy disk drive gently as far as it

goes.

 Attach the label to the correct position.

 Do not write anything directly onto the disk surface with a pencil or

ball-point pen.

 Do not open the shutter.

 Do not use the floppy disk in a dusty place.

 Do not place anything on the floppy disk.

 Do not leave the floppy disk in a high-temperature place (e.g., place

exposed to direct sunlight or close to a heater).

 Keep the floppy disk away from cigarette smoke.

 Keep the floppy disk away from any liquid (e.g., water) and

chemicals.

 Keep the floppy disk away from any magnetic objects (e.g.,

magnet).

 Do not pinch the floppy disk with a paper clip or drop it.

 Keep the floppy disk in a floppy disk case that protects it from

magnetism and dust.

 A floppy disk has a write-protect switch that prevents the stored data

from accidental erasure. You can read data from a write-protected
floppy disk, but you cannot save data into the floppy disk or format
it. NEC recommends that you should write-protect any floppy disk
containing valuable data unless you are about to save data. To
write-protect a 3.5-inch floppy disk, use the write-protect switch
provided on its back.

 The floppy disk is a very delicate storage media. Dust or thermal

changes, as well as operator's misconduct or sever failures, may
cause loss of data. To avoid loss of data, NEC recommends that
you should make a back-up copy of your valuable data on a regular
basis. (Make sure to make a back-up copy of every floppy disk
provided with the server.)

Write-protect switch

Write

disable

Write

enable

2-20 General Description

CD-ROM Drive

Your server is provided with the CD-ROM drive on its front to read data from a CD-ROM (read­only compact disk). The CD-ROM provides larger and faster data read than the floppy disk.

CAUTION

Observe the following instructions to use the server safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage. See
pages 1-3 to 1-8 for details.

■ Do not leave the tray ejected from the CD-ROM drive.

■ Take off the headphone before you plug in the headphone jack.

Setting and Removing the CD-ROM

Make sure that the server is powered (the POWER/SLEEP lamp is lit) before inserting a CD-ROM
into the CD-ROM drive.

Press the Open/Close button on the front of the CD-ROM drive to eject the tray. With the CD­ROM label facing up, place a CD-ROM in the tray gently and securely.

Press the Open/Close button or gently push on the tray front. The tray is automatically retracted
into the CD-ROM drive.

Open/Close button

General Description 2-21

IMPORTANT: If the CD-ROM drive produces large noise after the

setting of a CD-ROM, reload the CD-ROM.

To remove a CD-ROM, press the Open/Close button to eject the tray, as described for inserting it,
and then take the CD-ROM out of the tray. (The orange-lit access lamp indicates ongoing disk
access. The Open/Close button does not work while the lamp is lit.)

Your OS may have a command to eject the tray.

When you have taken out the CD-ROM, retract the tray back in place.

When you fail to eject:

When you fail to eject the CD-ROM tray with the Open/Close button and take out the CD-ROM
from the server, follow the procedure below.

1. Press the POWER switch to power off the server. (The POWER/SLEEP lamp goes off.)

2. Insert a metal pin of approximately 1.2 mm in diameter and 100 mm in length (a

straightened large paper clip will make a substitute) into the emergency hole on the right
front of the CD-ROM drive and gently push it in until the tray is ejected.

IMPORTANT:

 Do not use a toothpick or plastic stick that is easy to break.

 If the above procedure does not let you take out the CD-ROM,

contact your sales agent.

3. Hold the tray and pull it out.

4. Take out the CD-ROM.

5. Push the tray back into position.

2-22 General Description

Use of the CD-ROM

Keep the following notes in mind to use the CD-ROM for the server:

 For the disk which does not conform to the CD standard, the playback of such a disk with

the CD drive is not guaranteed.

 Do not drop the CD-ROM.

 Do not place anything on the CD-ROM or bend the CD-ROM.

 Do not attach any label onto the CD-ROM.

 Do not touch the signal side (nothing is printed on this side) with your hand.

 Place the CD-ROM with its printed side upward and gently put it on the tray.

 Do not scratch the CD-ROM or write anything directly on it with a pencil or ball-point

pen.

 Keep the CD-ROM away from cigarette smoke.

 Do not leave the CD-ROM in a high-temperature place (e.g., place exposed to direct

sunlight or close to a heater).

 When dust or fingerprints are attached on the CD-ROM, wipe the CD-ROM from its

center to edge with a dry soft cloth slowly and gently.

 Use the CD cleaner to clean the CD-ROM. Do not use record spray/cleaner, benzene, or

thinner.

 Keep the CD-ROM in a CD-ROM case when not in use.

 If the CD-ROM emits large noise in the CD-ROM drive, remove the CD-ROM and insert

it back again.

Chapter 3

Setting Up Your Server

This chapter describes how to set up your server appropriate for your system, on a step-by-step
basis.

3-2 Setting Up Your Server

SETUP FLOW

Follow the flowchart below to set up the server.

Unpacking the system

Unpack the server and accessories from the shipping carton box.

Installing optional devices

If you have purchased any optional device for the server, see Chapter 9 to install it.

Selecting the server site

Select a suitable site for the server.

Connecting peripheral devices

Connect peripheral devices to the server.

Connecting the power cord

Connect the power cord to the server.

Turning on the server

Power on the server to start software setups. Setups depend on the optional internal
devices installed and the peripheral devices connected.

Installing the operating system

Install an operating system to the server. See Chapter 5.

Installing the utilities

Install the utilities in the provided NEC EXPRESSBUILDER CD-ROM.
See Chapter 6.

Making backup copies of system information

After all the system setup procedures are completed, make backup copies of system
information.

System information is required for recovering the server from the trouble or after
replacing the system board.

Setting Up Your Server 3-3

UNPACKING THE SYSTEM

When you receive your system, inspect the shipping containers prior to unpacking. If the shipping
boxes are damaged, note the damage, and if possible, photograph it for reference. After removing
the contents of the containers, keep the cartons and the packing materials. If the contents appear
damaged when you unpack the boxes, file a damage claim with the carrier immediately.

INSTALLING OPTIONAL DEVICES

To install any optional device, see Chapter 9, "Upgrading Your Server," for the installation
procedure. Proceed to the next section if you have no optional devices to install.

IMPORTANT: There are third-party products (memory modules, hard

disks, etc.) available for the server in the markets. However, NEC
recommends that you should use NEC products for stable operation.
NEC assumes no liability for data errors and failures due to malfunction
of the server resulted from installation of those third-party products.

3-4 Setting Up Your Server

SELECTING SERVER SITE

Read the following precautions before selecting a suitable site for your server. The following
describes installation of the server and connections to the server.

CAUTION

Observe the following instructions to use the server safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage. See
pages 1-3 to 1-8 for details.

■ Never attempt to lift the server only by yourself.

■ Do not install the server in any place other than specified.

The following figure illustrates a site suitable for installing the server.

* It is recommended that the server should be used in a room where

temperature is in the range between 15 to 25ºC.

Clean and tidy room

Allow clearance of at least 150 mm in

front of and behind the server.

100 to 120 Vac/200 to 240
Vac parallel bi-polar wall
power outlet with the
ground line.

Room that satisfies the
following conditions for
operation: *
Temperature: 10 to 35ºC

Humidity: 20 to 80%

Close enough to connect the

mouse and the display.

Install the server on

a flat, rigid desk

Setting Up Your Server 3-5

When you have selected a server site, hold the server by its bottom with at least three persons and
carry it to the site, then place it slowly and gently.

IMPORTANT: Do not hold the server by its front mask to lift the

server. The front mask may be disengaged and damage the server.

Do not install the server in the following locations as it may cause malfunctions of the server.

 Places with drastic changes in temperature (e.g., near a heater, air conditioner, or

refrigerator)

 Places with strong vibration

 Places with corrosive gas in presence, near chemicals, or with possibilities of chemicals

sprayed over

 On a non-antistatic carpet

 Places with possibilities of falling objects

 Places where a power outlet that shares the ground line with another (especially the one to

which a device with large power consumption is connected) must be used for the server

 Do not install the server near equipment that generates power noise (e.g., contact spark at

power-on/power-off of commercial power supply through a relay). (To install the server
near equipment that generates power noise, ask your sales agent for separating the power
wiring or installing a noise filter.)

3-6 Setting Up Your Server

CONNECTING PERIPHERAL DEVICES

Connect peripheral devices to the server. The server is provided with connectors for wide variety
of peripheral devices. The figure on the next page illustrates available peripheral devices for the
server in the standard configuration and locations of the connectors for the devices.

CAUTION

Observe the following instructions to use the server safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage. See
pages 1-3 to 1-8 for details.

■ Do not use any damaged cable connector.

■ Do not use any unauthorized interface cable.

■ Do not use the server with any loose interface connection.

■ Do not step on the interface cable or place any heavy object on it.

IMPORTANT:

 Power off the server and a peripheral device before connection.

Connecting a powered peripheral device to the powered server will
cause malfunctions and failures.

 To connect a third-party peripheral device or interface cable to the

server, consult with your sales agent for availability of such a device
or cable. Some third-party devices may not be used for the server.

 To connect the provided keyboard and mouse, plug their connectors

to the server with the "∆" mark on the connectors facing right.

 Do not connect the serial ports with the telephone line directly.

 Do not connect any devices to the connectors not instructed in this

subsection. Doing so could damage the device, your server, or both.

Setting Up Your Server 3-7

Device with the serial
interface (e.g., modem)*

Keyboard

Mouse

Display unit

Hub
(multiport
repeater)

Printer with the
parallel interface

Device with the USB interface
(e.g., terminal adapter)

3-8 Setting Up Your Server

CONNECTING POWER CORD

Connect the provided power cord to the server.

WARNING

Observe the following instructions to use the server safely. Failure to follow
these instructions may result in death or serious personal injury. See pages 1­3 to 1-8 for details.

■ Do not hold the power plug with a wet hand.

CAUTION

Observe the following instructions to use the server safely. Failure to follow
these instructions may cause a fire, personal injury, or property damage. See
pages 1-3 to 1-8 for details.

■ Do not plug the power cord in to an improper power source.

■ Do not connect the power cord to an outlet that has an illegal number of

connections.

■ Insert the power plug into the outlet as far as it goes.

■ Use the authorized power cord only.

1. Plug the provided power cord into the power receptacle on the rear of the server.

2. Plug the other end of the power cord into the wall outlet.

Setting Up Your Server 3-9

To connect the power cord from the server to an interruptive power supply (UPS), use service
outlets on the rear of the UPS.

The UPS service outlets are categorized into two groups: SWITCH OUT and UN-SWITCH OUT.
(They may be called "OUTPUT1" and "OUTPUT2".)

To control power supply with an application (NEC ESMPRO UPSController) that controls the UPS,
connect the power cord to an SWITCH OUT outlet.

For constant power supply, connect the power cord to a UN-SWITCH OUT outlet. (Connect the
modem that is in service for 24 hours to this outlet.)

<Example>

When the power cord from the server to a UPS, change the BIOS setup utility of the server to link
with power supply from the UPS.

Change a parameter for "AC-LINK" of the Advanced menu of the BIOS setup utility. See Chapter
4 for details.

UN-SWITCH OUT

(OUTPUT 2)

SWITCH OUT

(OUTPUT 1)

3-10 Setting Up Your Server

TURNING ON THE SERVER

Turn on the server and follow the on-screen instructions for setup.

IMPORTANT: Before turning on the server:

 Some optional boards require setups with the BIOS setup utility

before installation. If the server has a PCI board with the PCI-to­PCI bridge installed, the BIOS setup utility is enabled to launch.
Check on the board specifications to find out whether it requires
pre-installation setups before actually installing the board.

 Some installed optional devices or connected peripheral devices

require setups before proceeding to the next step.

To use the server with no optional devices installed besides the graphic
board, install a desired OS to the server.

1. Make sure all external devices, such as a video display, keyboard, and mouse (optional)

have been connected, and the power cords are connected.

2. Power on the video display and any other external devices.

3. Make sure that the floppy disk drive contains no floppy disk and the CD-ROM drive

contains no bootable CD-ROM.

4. Press the POWER/SLEEP switch.

NOTES:

 If the power cord is connected to the power control unit such as the

UPS, turn on the power control unit.

 Connect the power cord and wait a few seconds before pressing the

POWER switch. The POWER/SLEEP switch does not work in a
few seconds after connecting the power cord due to firmware start­up.

POWER/SLEEP lamp

Setting Up Your Server 3-11

The POWER/SLEEP lamp on the front of the server comes on.

In a few seconds, the NEC logo appears on the screen and the Power On Self-Test (POST)
begins.

The POST runs automatically when you power on the server or reset it with a keyboard
operation (Ctrl + Alt + Delete). The POST runs diagnostics, initializes the server, sets
interrupt vectors, detects installed peripheral devices, and boots the operating system (if
installed). See Chapter 2 for detailed description on POST.

If the server halts before completing the POST, the POST emits a beep code indicating a
fatal system error requiring immediate attention. (See Chapter 8, "Troubleshooting," for
troubleshooting information.)

During memory test, the POST displays the amount of memory it was able to access and
test. Depending on the amount of installed memory, it may take several minutes to
complete the memory test.

NOTE: The factory-set is defined to hide the POST screen with the

NEC logo screen. You can always change the NEC logo screen to the
POST screen by pressing Tab. To change the start-up screen, use the
BIOS setup utility, "CMOS Setup." (See Chapter 4 for details.)

During the POST, you will see the banner message to prompt you to launch the BIOS setup utility
stored in ROM on the mother board or on an installed option board.

Start the BIOS setup utility appropriate to your system environment to change the CMOS Setup.
For detail explanation on the BIOS setup utility for the server, see Chapter 4. For the BIOS utility
for the option board, refer to the manual that comes with the option board.

IMPORTANT: Always allow POST to complete before turning off

your system.

3-12 Setting Up Your Server

INSTALLING OPERATING SYSTEM

See Chapter 5 for installing Microsoft Windows Server 2003 and Microsoft Windows 2000.

To install the other operating system listed above, contact your sales agent.

IMPORTANT: Use NEC EXPRESSBUILDER for initial setup of

your server. The NEC EXPRESSBUILDER is a support software for
the server. It simplifies the process of installing and configuring your
server. See Chapter 6 for details on NEC EXPRESSBUILDER.

INSTALLING UTILITIES

Install the utilities that come with the server. See Chapter 6 for details.

MAKING BACKUP COPIES OF SYSTEM INFORMATION

The system information includes the current BIOS settings and any specific information for the
server.

Save the information after completing the system setup.

Without the backup data, you will not be able to recover the information.

You can save the information by the following process.

1. Set the "NEC EXPRESSBUILDER" CD-ROM in the CD-ROM drive and reboot the

system.

2. Select [Tools].

3. Select [Off-line Maintenance Utility].

4. Select [System Information Management].

5. Insert a floppy disk into the floppy disk drive.

6. Select [Save].

Chapter 4

Configuring Your Server

Configuration and setup utilities are used to change your system configuration. You can configure
your system, as well as option boards you may add to your system, using the BIOS Setup utility.
Several unique system parameters are configured using the BIOS Setup utility, which is stored in
the system FLASH memory.

The Array Configuration Utility (ACU) controls the serial ATA hard disk drives as a RAID drive.
Use this utility if you need to configure the RAID drive with the serial ATA hard disk drives or to
perform a RAID disk format or verify disk operation on the serial ATA disk drives. The Array
Configuration Utility is used only for the serial ATA hard disk drives that are connected with the
serial ATA channel on your server board.

If your system has been factory configured, the BIOS Setup utility or Array Configuration Utility do
not need to be run unless you want to change the password or security features, add certain types of
option boards or devices, or upgrade your mother board.

This chapter also provides information on several system configuration parameters that are set by
jumpers on the system board. However, these parameters do not usually require change.

Use NEC EXPRESSBUILDER CD-ROM to create the device driver diskettes.

4-2 Configuring Your Server

SYSTEM BIOS (BIOS SETUP UTILITY)

The BIOS Setup utility is provided to make basic hardware configuration for the server. This
utility is pre-installed in the flash memory of the server and ready to run.

The server is configured with the correct parameters using the BIOS Setup utility and shipped in the
best conditions. Thus, you don't need to use the BIOS Setup utility in most cases. However, you
might wish to use the BIOS Setup utility in the cases described below.

IMPORTANT:

 The BIOS Setup utility is intended for system administrator use

only.

 The BIOS Setup utility allows you to set a password. The server is

provided with two levels of password: Supervisor and User. With
the Supervisor password, you can view and change all system
parameters of the BIOS Setup utility. With the User password,
system parameters available for viewing and changing are limited.

 Do not set any password before installing the OS.

 The server contains the latest version of the BIOS Setup utility.

Dialog boxes appear on your BIOS Setup utility, thus, may differ
from descriptions in this manual. If you find anything unclear, see
the online help or ask your sales agent.

Configuring Your Server 4-3

Starting SETUP Utility

A few seconds after powering on, the following message appears at bottom left on the screen.

Press <F2> to enter SETUP or Press <F12> to LAN Boot

Press F2 to start the BIOS Setup utility and display its Main menu.

If you have previously set a password with the BIOS Setup utility, the password entry screen
appears. Enter the password.

Enter password:[ ]

Up to three password entries will be accepted. If you fail to enter the password correctly for three
consecutive times, the server halts. (You can no longer proceed.) Power off the server.

NOTE: The server is provided with two levels of password:

Administrator and User. With the Administrator password, you can
view and change all system parameters. With the User password,
system parameters available for viewing and changing are limited.

4-4 Configuring Your Server

Description on On-Screen Items and Key Usage

Use the following keyboard keys to work with the BIOS Setup utility. These keys are also listed at
the bottom of the menu screen.

Cursor (↑, ↓):

Move cursor up and down. The cursor moves only to the settings
that you can change.

Cursor (←, →):

Move between menus.

– and +:

Select the previous value (–) or the next value (+) for the field.

Enter

Execute command or select ³ submenu.

Esc

Exit the current menu and return to the previous menu.

F1:

Get Help about an item.

F9:

Load default configuration values for this menu.

F10:

Save configuration values and exit.

Indicates the current menu.

Indicates there
are submenus.

Setup item
menu

Explanation of key functions menu

Parameter (high-lights upon selection) menu

Online
help
window

Configuring Your Server 4-5

Configuration Examples

The following describes examples of configuration required to use software-link features or for
system operations.

Time and Date Settings

You can also change the time and date settings via the operating system commands.

Select [Main] - [System Time].

Select [Main] - [System Date].

Link with Management Software

To control power supply of the server with NEC ESMPRO Manager via the network

Select [Advanced] - [Advanced Chipset Control] - [Wake On LAN/PME] - [Enabled].

Select [Server] - [AC LINK] - [Stay Off].

ATA Drive Settings

To check the ATA drives connected with the onboard ATA channels.

Select [Main] - [Primary IDE Master], [Primary IDE Slave], [IDE Secondary/Master], and
[IDE Secondary/Slave].

To configure the RAID drive.

Select [Advanced] - [I/O Device Configuration] - [SATA Controller Mode Option] ­[Enhanced] - [SATA RAID Enabled], [Enabled], and use the RAID configuration utility
(see "RAID Configuration Utility" in this chapter).

UPS

To link power supply with the UPS

 To power on the server when power is supply from the UPS

Select [Server] - [AC LINK] - [Power On].

 To keep the server off-powered even when power is supplied from the UPS

Select [Server] - [AC LINK] - [Stay Off].

4-6 Configuring Your Server

Boot

To change the boot order of devices connected to the server

Select [Boot] and specify the boot order.

To display POST check results

Select [Advanced] - [Boot-time Diagnostic Screen] - [Enabled].

You can also press Esc while the NEC log is on the screen to display POST check results.

To control from the remote console

Select [Server] - [Console Redirection] and set each item.

Memory

To check the installed memory (DIMM board) status

Select [Advanced] - [Memory Configuration] and check the status indications.

The on-screen DIMM group numbers and socket locations on the mother board are
associated as shown in the following figure.

To clear the memory (DIMM board) error information

Select [Advanced] - [Memory Configuration] - [Memory Retest] - [Yes] and reboot.

To run power-on memory test

Select [Advanced] - [Memory Configuration] - [Extended RAM Step] - [1MB] and
reboot.

DIMM Group #1

DIMM Group #2

DIMM Group #3

DIMM Group #4

Configuring Your Server 4-7

CPU

To check the installed CPU status

Select [Main] - [Advanced Processor Options] – [Processor 1 CPUID] and check the
status indications.

To clear the CPU error information

Select [Main] - [Advanced Processor Options] - [Processor Retest] – [Yes] and reboot.

Keyboard

To set Numlock

Select [Advanced] - [Numlock] – [Auto]/[On]/[Off].

Security

To set passwords on the BIOS

Select [Security] - [Set Administrator Password] and enter a password.

Select [Security] - [Set User Password] and enter a password.

Set Administrator password first, then User password.

External Devices

To set up external devices

Select [Advanced] - [I/O Device Configuration] and set up each device.

Internal Devices

To set up internal PCI devices of the server

Select [Advanced] - [Advanced Chipset Control] - [PCI Device] and set up each device.

To install the disk array controller board or SCSI controller board

Select [Advanced] - [PCI Configuration] - [PCI Slot n Option ROM] - [Enabled].
n: slot number

To clear the hardware configuration data (after installing/removing internal devices)

Select [Advanced] - [Reset Configuration Data] - [Yes].

4-8 Configuring Your Server

Saving the Configuration Data

To save the current configuration data

Select [Exit] - [Exit Saving Changes] or [Save Changes].

To discard changes to the current configuration data

Select [Exit] - [Exit Discarding Changes] or [Discard Changes].

To load the user-defined default

Select [Exit] - [Load Setup Defaults].

Configuring Your Server 4-9

Menu and Parameter Descriptions

The SETUP utility has the following six major menus:

 Main

 Advanced

 Security

 Server

 Boot

 Exit

To set minute functions, select a submenu from the above menus. The following describes
available functions and parameters, as well as the factory-set, for each menu.

Main

If BIOS Setup is started, the Main menu appears first. If you select a menu item preceded by
symbol ³ and press Enter, the appropriate submenu appears.

The items which can be set on the Main menu screen and their functions are described below.

4-10 Configuring Your Server

Option Parameter Description Your Setting

System Time HH:MM:SS Set the system time.
System Date MM/DD/YYYY Set the system date.
Legacy Diskette A Disabled

360Kb 51/

4

1.2MB 51/

4

720Kb 31/

2

[1.44/1.25MB 31/2]

2.88MB 31/

2

Set the settings of floppy disk
drive A (standard configuration).

Legacy Diskette B [Disabled]

360Kb 5

1

/

4

1.2MB 51/

4

720Kb 31/

2

1.44/1.25MB 31/

2

2.88MB 31/

2

Set the settings of floppy disk
drive B. No second floppy disk
drive is included in this system.

Hard Disk Pre-Delay [Disabled]

3 seconds
6 seconds
9 seconds
12 seconds
15 seconds
21 seconds
30 seconds

Allows slower spin-up drives to
come ready.

Primary IDE Master/
Primary IDE Slave

Secondary IDE/Master
Secondary IDE/Slave

Select submenu Set the information on the device

connected to each channel on
the submenu. The settings of
some items may be changed.
However, leave the items as they
are at the shipment.

Advanced Processor
Options

Select submenu Shows the processor settings

submenu.

Language [English (US)]

Français
Deutsch
Español
Italiano

Select which language BIOS
displays.

[ ]: Factory-set

Configuring Your Server 4-11

Advanced Processor Options

If you select "Advanced Processor Options" on the Main menu, the screen shown below appears.

See the table below for the items.

Option Parameter Description Your Setting

Processor Retest [No]

Yes

If yes, BIOS will clear historical
processor status and retest the
processor on the next boot.

CPU Speed nnn GHz

Displays clock speed for the
processor. (View only)

Processor 1
CPUID

Numeral
Disabled

Displays CPU ID for processor, if
present.

"Disabled" indicates that the
processor is defected. (View only)

Processor 1 L2
Cache

nnn KB Displays L2 cache size for processor.

Hyper-Threading
Technology

[Enabled]
Disabled

Disable or enable the
Hyper-Threading Technology.

[ ]: Factory-set

4-12 Configuring Your Server

Advanced

The Advanced menu appears if you move the cursor to the position of "Advanced."

If you select a menu item preceded by symbol

³ and press Enter, the appropriate submenu appears.

See the table below for the items.

Option Parameter Description Your Setting

Boot-time
Diagnostic Screen

[Disabled]
Enabled

If enabled, the BIOS will display the NEC
logo during POST. Press Esc to switch to
the POST execution screen.

Reset
Configuration Data

[No]
Yes

Select "Yes" if you want to clear the system
configuration data during the next boot.
Automatically reset to "No" in the next boot.

NumLock [Auto]

On
Off

Sets power on Numlock state.

Memory/Processor
Error

[Boot]
Halt

If "Halt" is selected, the boot is stopped
when POST error occurs.

Multiprocessor
specification

1.1
[1.4]

Defines Multiprocessor Specification (MPS)
version.

[ ]: Factory-set

Configuring Your Server 4-13

Memory Configuration

The following screen appears if you select "Memory Configuration" on the Advanced menu.

See the table below for the items.

Option Parameter Description Your Setting

System Memory nnn KB Indicates the total capacity of the basic

memory. (View only)

Extended Memory nnnnnnn KB Indicates the total capacity of the

extended memory. (View only)

DIMM Group #1 ­#4 Status

Normal
Not installed
Disabled

Displays the current status of the
memory bank. Disabled indicates that
a DIMM in the bank has failed and the
entire bank has been disabled.

Memory Retest [No]

Yes

Causes BIOS to retest all memory on
the next boot.

Extended RAM
Step

1MB
[Disabled]

"1MB" indicates that the memory test
is done in the unit of 1MB. "Disabled"
indicates that only memory
initialization is done.

[ ]: Factory-set

4-14 Configuring Your Server

PCI Configuration

The following screen appears if you select "PCI Configuration" on the Advanced menu. Selecting
an item on the screen allows the proper submenu to appear.

Option Parameter Description Your Setting

PCI Slot 1 Option
ROM – PCI Slot 5
Option ROM

[Enabled]
Disabled

Enable option ROM scan of the
selected device.
When the graphics accelerator board
is installed or the disk array controller
or SCSI controller boards to be
installed are connected to the hard
disk in which OS is installed, set this
item to "Enabled." When the LAN
controller board with installation of the
option ROM BIOS is used but the
board does not provide network
booting, set this item to "Disabled."

[ ]: Factory-set

Configuring Your Server 4-15

– Embedded Video Controller submenu

Option Parameter Description Your Setting

Onboard VGA
Control

Disabled
[Enabled]

Specify whether the onboard graphics

controller is enabled or disabled.
Pre-Allocated
Memory Size

1MB
[8MB]

Specify the memory size for internal

graphics device.

[ ]: Factory-set

– Embedded NIC (Gbit #1) submenu

Option Parameter Description Your Setting

Onboard LAN1
Control

Disabled
[Enabled]

If Disabled, the BIOS will hold the

embedded chip in reset. In this

configuration, the controller hardware is

completely disabled, and will be invisible to

the PnP operating systems.
Option ROM Scan Disabled

[Enabled]

If Enabled, initialize device expansion ROM.

[ ]: Factory-set

4-16 Configuring Your Server

I/O Device Configuration

The screen shown below appears if you select "I/O Device Configuration" on the Advanced menu.

See the table below for the items.

IMPORTANT: Note that the interrupt and/or base I/O address are not

overlapped with others. If the value set for the interrupt or base I/O
address is used in another resource, the yellow asterisk (*) appears.
Reset any item with the yellow asterisk properly.

Option Parameter Description Your Setting

Serial Port A Disabled

[Enabled]

Selects whether serial port A is
enabled or disabled.

Base I/O Address [3F8/IRQ4]

2F8/IRQ3
3E8/IRQ4
2E8/IRQ3

Selects the base I/O address for serial
port A.

Interrupt IRQ 3

[IRQ 4]

Selects the interrupt for a serial port A.

Serial Port B Disabled

[Enabled]

Selects whether serial port B is
enabled or disabled (display only).

Parallel Port Disabled

[Enabled]

Selects whether the parallel port is
enabled or disabled.

Mode [Bi-directional]

EPP
ECP

Selects the operation mode of the
parallel port.

Base I/O address [378]

278

Selects the base I/O address for
parallel port.

Interrupt IRQ5

[IRQ7]

Selects the interrupt for parallel port.

PS/2 Mouse Disabled

[Enabled]

If disabled, PS/2 mouse port will not
function.

Configuring Your Server 4-17

Option Parameter Description Your Setting

USB Controller Disabled

[Enabled]

If disabled, the USB ports do not
accept the USB device class 3 (HID:
Human Interface Deice).

USB 2.0 Controller Disabled

[Enabled]

If disabled, the USB2.0 device will not
function.

Legacy USB
Support

Disabled
[Enabled]

Selects whether the USB keyboard is
made available in OS which does not
support USB formally.

Serial ATA Disabled

[Enabled]

Selects whether the serial ATA is
enabled or disabled.

Native Mode
Operation

[Auto]
Serial ATA

Selects the native mode for ATA.
Note: A specific OS does not support

the native mode.

SATA Controller
Mode Option

[Compatible]
Enhanced

Compatible mode:

SATA and PATA drives are
automatically detected and
recognized as legacy mode.

Enhanced mode:

SATA and PATA drives are
automatically detected and
recognized as native mode.

Note: The pre-installed Windows 2000
does not work in enhanced mode.

SATA AHCI Enabled [Disabled]

Enabled

The server does not support the AHCI
feature. Always set this item to
[Disabled].

SATA RAID Enabled [Disabled]

Enabled

Selects whether the RAID disk drives
that uses the onboard SATA is
enabled or disabled.

Note: If you attempt to start the system
from SATA hard disk drive with
different setting, the data may be
destroyed.

[ ]: Factory-set

4-18 Configuring Your Server

Advanced Chipset Control

The following screen appears if you select "Advanced Chipset Control" on the Advanced menu.

See the table below for the items.

Option Parameter Description Your Setting

Enable Multimedia
Timer

[No]
Yes

Specify whether the timer
corresponding to multimedia is
enabled or disabled.

Wake On
LAN/PME

Disabled
[Enabled]

Specify whether the remote power-on
function through embedded NIC, PCI
devices in slots 1 to 5 is enabled or
disabled.

Wake On Ring [Disabled]

Enabled

Specify whether the remote power-on
function through a serial port is
enabled or disabled.

Wake On RTC
Alarm

[Disabled]
Enabled

Specify whether the remote power-on
function by using RTC alarm feature is
enabled or disabled.

[ ]: Factory-set

Configuring Your Server 4-19

ICH6 Root Port #1 Sub-Menu

The following screen appears if you select "ICH6 Root Port #1 Sub-Menu" on "Advanced Chipset
Control" in the Advanced menu.

See the table below for the items.

Option Parameter Description Your Setting

PCI Express Port #1 Disabled

Enabled
[Auto]

If disabled, PCI Express Port #1
will not accept PCI Express device.

Port #1 Enabled – Displays the Port #1 Enabled or

Disabled. (View only)

Port #1 Number – Displays the Port #1 Number.

(View only)

Port #1 Width – Displays the Port #1 Width. (View

only)

Port #1 Slot Number – Displays the Port #1 Slot Number.

(View only)

Port #1 Power Limit – Displays the Port #1 Power Limit.

(View only)

Port #1 Slot Card Detected – Displays the Port #1 Slot Card

Detected or not Detected. (View
only)

[ ]: Factory-set

4-20 Configuring Your Server

PCI Device

The following screen appears if you select "PCI Device" in "Advanced Chipset Control" on the
Advanced menu.

See the table below for the items.

Option Parameter Description Your Setting

PCI IRQ line 1
PCI IRQ line 2
PCI IRQ line 3
PCI IRQ line 4
PCI IRQ line 5

Disabled
[Auto Select]
3
4
5
6
7
9
10
11
12
14
15

PCI devices use hardware interrupts
called IRQs. A PCI device cannot use
IRQs already in use by ISA devices.
Use "Auto" only if no ISA legacy cards
are installed.

[ ]: Factory-set

Configuring Your Server 4-21

Security

The Security menu appears if you move the cursor to the position of "Security."

Press Enter on "Set Administrator Password" or "Set User Password," to display the following
screen.

Enter the passwords on the dialog box. Passwords may have up to seven characters including
alphanumerics and symbols.

IMPORTANT:

 User password can be set only when Administrator password is

already set.

 Set the passwords only after OS is installed.

 If you forget the passwords, contact your service representative.

4-22 Configuring Your Server

See the table below for the items.

Option Parameter Description Your Setting

User Password Is Clear

Set

Status only, user cannot modify.
Once set, this can be disabled by
setting it to a null string, or by clearing

password jumper on system board
(see Configuring Mother Board
Jumpers in this Chapter).

Supervisor
Password Is

Clear
Set

Status only, user cannot modify.
Once set, this can be disabled by

setting it to a null string, or by clearing
password jumper on system board
(see Configuring Mother Board
Jumpers in this Chapter).

Set User
Password

Up to eight
alphanumerics

Supervisor password controls access
to the setup utility.

When Enter is pressed, the user is
prompted for a password; press Esc
to abort. Once set, this can be
disabled by setting it to a null string, or
by clearing password jumper on
system board (refer to Configuring
Mother Board Jumpers in this
chapter).

Set Supervisor
Password

Up to eight
alphanumerics

When the <Enter> key is pressed, the
user is prompted for a password;
press ESC key to abort. Once set, this
can be disabled by setting it to a null
string, or by clearing password jumper
on system board (refer to Configuring
Mother Board Jumpers in this
chapter).

Password on boot [Disabled]

Enabled

Disables or enables password entry
on boot.

Fixed disk boot
sector

[Normal]
Write Protect

Will write protect the boot sector of the
hard drive to prevent viruses from
corrupting the drive under DOS if set
to write protect.

Diskette access User

[Supervisor]

Controls access to the floppy disk
drive.

[ ]: Factory-set

Configuring Your Server 4-23

Server

The Server menu appears if you move the cursor to "Server."

See the table below for the items.

Option Parameter Description Your Setting

Assert NMI on
SERR

Disabled
[Enabled]

Indicates whether PCI SERR is
supported or not.

Post Error Pause Disabled

[Enabled]

Indicates whether POST is aborted once
at the end of POST if an error occurs
during the execution of POST.

AC LINK Stay Off

[Last State]
Power On

Indicates the AC LINK function. Shows
the state of the power of the server.

[ ]: Factory-set

IMPORTANT:

 To power on the server from the UPS (Uninterruptible Power

Supply), select [Server] - [AC Link] - [Power On].

 If the server is connected to the UPS, set at least 10 seconds delay in

the power-on schedule.

The table below shows the operation when the AC power to the server is turn off once and then on
again, depending on the setting of "AC LINK."

Setting of AC LINK

System status before AC power off

Stay Off Last State Power On

Operating Off On On
Aborting (DC power being off also) Off Off On
Forced shutdown Off Off On

* Press the power switch continuously for four seconds or longer. This forcibly turns off the

power.

4-24 Configuring Your Server

System Management

The following screen appears if you select "System Management" on the Server menu and press
Enter.

See the table below for the items.

Option Parameter Description Your Setting

BIOS Version -

Displays the current BIOS version.
(View only)

Board Part
Number

-

Displays the mother board part
number. (View only)

Board Serial
Number

-

Displays the mother board serial
number. (View only)

System Part
Number

-

Displays the system part number.
(View only)

System Serial
Number

-

Displays the System serial number.
(View only)

Chassis Part
Number

-

Displays the chassis part number.
(View only)

Chassis Serial
Number

-

Displays the chassis serial number.
(View only)

GBIA Module
Version

-

Displays the GBIA module version.
(View only)

Configuring Your Server 4-25

Console Redirection

The following screen appears if you select "Console Redirection" on the Server menu and press
Enter.

See the table below for the items.

Option Parameter Description Your Setting

BIOS Redirection
Port

[Disabled]
Serial Port A

Specify the address/interrupt of the
serial port to which a remote console
is connected.

ACPI Redirection
Port

[Disabled]
Serial Port A

Specify the serial port to which an
ACPI console is connected.

Baud Rate 9600

[19.2k]

38.4k

57.6k

115.2k

Specify the baud rate used for the
interface with successive remote
consoles.

Terminal Type [PC ANSI]

VT100+
VT-UTF8

Specify the type of remote console.

Flow Control None

XON/XOFF
[CTS/RTS]
CTS/RTS+CD

Specify the flow control method.

[ ]: Factory-set

4-26 Configuring Your Server

Boot

If you move the cursor to the position of "Boot," the Boot menu appears, which is used to set the
boot priority.

The server searches for devices in the order set in this menu on booting. Finding the boot software,
the server starts the software.

The priority of the boot devices can be changed by using the ↑, ↓, +, and - keys. Move the cursor
to the desired device with the ↑ or ↓ key and change the priority with the + or - key.

IMPORTANT: To boot NEC EXPRESSBUILDER, set the priority of

the devices as shown in the figure above.

Configuring Your Server 4-27

Exit

The Exit menu appears if you move the cursor to "Exit."

The options on the menu are described below.

Exit Saving Changes

Exit after writing all modified BIOS Setup item values to CMOS.

Exit Discarding Changes

Exit leaving CMOS unmodified. User is prompted if any of the setup fields ware modified.

Load Setup Defaults

Load default values for all BIOS Setup items.

IMPORTANT: This option sets [SATA RAID Enabled] in the

[Advanced] - [I/O Device Configuration] menu to [Disable]. If the
SATA hard disk drives are installed in your server and the onboard
SATA RAID feature is used, change the parameter of the [SATA RAID
Enabled] from [Disable] to [Enable] before exiting BIOS Setup.

Discard Changes

Read the previous values of the all BIOS Setup items from CMOS.

Save Changes

Write all BIOS Setup item values to CMOS.

4-28 Configuring Your Server

ADD-IN CARD'S BIOS

Refer to the documentation coming with the optional add-in card for details.

When the server has multiple optional PCI boards installed, the server first displays the start-up
message of the CMOS Setup Utility of the mother board. It then displays the utility start-up
message for optional PCI boards one by one. The start-up message appears for the optional PCI
board in the PCI #1 slot first, then PCI #2, PCI #3, PCI #4, and finally PCI #5. The message
displayed may vary depending on the optional PCI board. Refer to the manual that comes with the
optional PCI board for details.

Configuring Your Server 4-29

CONFIGURING MOTHER BOARD JUMPERS

You can use the following procedure to clear the CMOS data in the server.

IMPORTANT:

 Clearing the CMOS data resumes the factory-set configuration data.

 Do not change any other switch settings. Any change may cause

the server to fail or malfunction.

The following describe the clearing procedure.

WARNING

Do not disassemble, repair, or alter the server.

Never attempt to disassemble, repair, or alter the server on any occasion other
than described in this manual. Failure to follow this instruction may cause an
electric shock or fire as well as malfunctions of the server.

1. Power off the server and disconnect the power cord and all the cables connected on the

rear of the server.

2. Remove the left side cover (see Chapter 9).

3. Remove the jumper from position 2 - 3 on jumper block.

4. Install the jumper on position 1 - 2 (CMOS clear) of the jumper block. Refer to the

following figure to find the location of this jumper.

4-30 Configuring Your Server

5. After three seconds later, reinstall the jumper.

6. Reinstall the server and then turn on the power.

7. Press F2 at the prompt to run the BIOS Setup utility, and select "Load Setup Default" at

the Exit menu.

IMPORTANT: If the SATA hard disk drives are installed in your

server and the onboard SATA RAID feature is used, change the
parameter of the [SATA RAID Enabled] in the [Advanced] - [I/O
Device Configuration] menu from [Disable] to [Enable] before exiting
BIOS Setup.

Configuring Your Server 4-31

RAID CONFIGURATION UTILITY

Your server includes the serial ATA RAID controller by supporting the RAID levels 0 and 1. The
Array Configuration Utility (ACU) that is an embedded BIOS utility is used to create, configure,
and manage arrays.

NOTES:

 You can also configure the SATA RAID drive by using NEC

EXPRESSBUILDER. Refer to Chapter 6 for detail.

 To configure the RAID drive with the SCSI or IDE hard disk drives,

purchase the optional RAID controller board and hard disk drives.

Installing the Hard Disk Drives

Install the two serial ATA hard disk drives to your server. Refer to Chapter 9 for detail.

IMPORTANT: Use hard disks of the same capacity and revolution.

Activating the SATA RAID Feature

To run the Array Configuration Utility (ACU), run the BIOS setup utility and change the "SATA
RAID Enable" option in the "I/O Device Configuration" of "Advanced" menu to "Enable". Refer to
"System BIOS (BIOS SETUP Utility)" described earlier in this chapter for detail.

4-32 Configuring Your Server

Running the Array Configuration Utility (ACU)

To run ARC, press Ctrl + A when prompted by the following message during the system startup:

Press <Ctrl><A> for Adaptec RAID Configuration Utility

The ARC menu appears, presenting these options:

 Array Configuration Utility (ACU)

 Disk utilities

To select an option from this menu, browse with the arrow keys and then press Enter. In some
cases, selecting an option displays another menu. To return to the previous menu at any time, press
Esc.

Configuring Your Server 4-33

Using the Array Configuration Utility

The Array Configuration Utility (ACU) enables you to create, manage, and delete arrays from the
controller’s BIOS, and initialize drives.

Managing Arrays

Use the Manage Arrays option to view array properties and members, and delete arrays. The
following sections describe these operations in greater detail.

Viewing Array Properties

To view the properties of an existing array:

1. At the BIOS prompt, press Ctrl + A.

2. From the ACU menu, Array Configuration Utility.

3. From the main menu, select Manage Arrays.

4. From the List of Arrays dialog box, select the array you want to view and press Enter.

The Array Properties dialog box appears, showing detailed information on the array. The
physical disks associated with the array are displayed here.

5. Press Esc to return to the previous menu.

4-34 Configuring Your Server

Deleting Arrays

IMPORTANT: Back up the data on an array before you delete it.

Otherwise, all data on the array is lost. Deleted arrays cannot be
restored.

To delete an existing array:

1. Turn on your server and press Ctrl + A when prompted to access the ACU.

2. From the ACU menu, Array Configuration Utility.

3. From the main menu, select Manage Arrays.

4. Select the array you wish to delete and press Delete.

5. In the Array Properties dialog box, select Delete and press Enter.

The following prompt is displayed:

Warning!! Deleting the array will render array unusable. Do you want to delete
the array?(Yes/No):

RAID 1 only—the following prompt is also displayed:

Deleting the partition will result in data loss! Do you also want to delete the
partition? (Yes/No):

6. Press Y to delete the array or partition or N to return to the previous menu.

7. Press Esc to return to the previous menu.

Configuring Your Server 4-35

Creating Arrays

Before creating arrays, make sure the disks for the array are connected and installed in your system.
Note that disks with no usable space, or disks that are uninitialized are shown in gray and cannot be
used. See Initializing Disk Drives described later.

To create an array:

1. Turn on your server and press Ctrl + A when prompted to access the ACU.

2. From the ACU menu, Array Configuration Utility.

3. From the main menu, select Create Array.

4. Select the disks for the new array and press Insert. To deselect any disk, highlight the

disk and press Delete.

5. Press Enter when both disks for the new array are selected.

The Array Properties menu displays.

4-36 Configuring Your Server

Assigning Array Properties

NOTE: Once the array is created and its properties are assigned, you

cannot change the array properties using the ACU. Instead, use Adaptec
Storage Manager - Browser Edition. (See Chapter 6 for details.)

To assign properties to the new array:

1. In the Array Properties menu, select an array type and press Enter. Note that only the

available array types, RAID0 and RAID1, are displayed. Each of these types requires two
drives.

2. Type in an optional label for the array and press Enter.

Configuring Your Server 4-37

3. For RAID0, select the desired stripe size. Available stripe sizes are 16, 32, and 64 KB

(default).

NOTE: NEC recommends that you do not change the default.

4. Create RAID via allows you to select between the different creation methods for RAID0

and RAID1. The following table gives examples of when each is appropriate.

RAID level Create via When appropriate

RAID0 No Init Creating a RAID0 on new drives.
RAID0 Migrate Creating a RAID0 from on new drive and one drive with

data you wish to preserve. (Your server does not support
this option.)

RAID1 Build Any time you wish to create RAID1, but especially if you

have data on one drive that you wish to preserve. (Your
server does not support this option.)

RAID Clear Creating a RAID1 on new drives, or when you want to

ensure that the array contains no data after creation.

RAID1 Quick Init Fastest way to create a RAID1. Appropriate when using

new drives.

4-38 Configuring Your Server

NOTES:

 Before adding a new drive to an array, back up any data contained

on the new drive. Otherwise, all data will be lost.

 If you stop the Build or Clear process on a RAID1 from ACU, you

can only restart it from Adaptec Storage Manager - Browser
Edition. (See Chapter 6 for details.)

 A RAID1 created using the Quick Init option may return some data

miscompares if you later run a consistency check. This is normal
and is not a cause for concern.

 The ACU allows you to use drives of different sizes in a RAID1.

During a build operation however, only the smaller drive can be
selected as the source or first drive.

 Adaptec does not recommend that you build an array on Windows

dynamic disks (volumes), as it will result in data loss.

5. Select a source drive from the Select Source Drive list box and press Enter.

6. When you are finished, press Done.