NEC N500i User Manual

Emergency Services and Safety Precautions

Emergency Services

To make an emergency call in any country

☛ Press 1 1 2 .

Ask the operator for the service which you require: Police, Ambulance, Fire Brigade, Coastguard or Mountain Rescue Services. Give your position and, if possible, remain stationary to maintain phone contact. The 112 emergency number service is available on every digital network service. The number 999 is an alternative emergency number for the UK only, and can only be used with a valid SIM card.

2 Due to the nature of the cellular system, the success of emergency calls

cannot be guaranteed.

General Care

A cellphone contains delicate electronic circuitry, magnets, and battery systems. You should treat it with care and give particular attention to the following points.

• Do not allow the phone or its accessories to come into contact with liquid or moisture

at any time.

• Do not place anything in the folded phone.

• Do not expose your phone to extreme high or low temperatures.

• Do not expose your phone to naked flame, cigars or cigarettes.

• Do not paint your phone.

• Do not drop or subject your phone to rough treatment.

• Do not place the phone alongside computer disks, credit cards, travel cards and other

magnetic media. The information contained on disks or cards may be affected by the phone.

• Do not leave the phone or the battery in places where the temperature could exceed

60°C; e.g. on a car dashboard or on a window sill, behind glass in direct sunlight, etc.

• Do not remove the phone’s battery while the phone is switched on.

• Take care not to allow metal objects, such as coins or key rings, to contact or short-

circuit the battery terminals.

• Do not dispose of battery packs in a fire. Your phone's Li-ion batteries may be safely

disposed of at Li-ion recycling points. For more specific battery and power supply information, see page 3.

• Do not put your phone's battery in your mouth as battery electrolytes may be toxic if

swallowed.

• Do not attempt to dismantle the phone or any of its accessories.

• This equi pment is fitted with an internal battery th at can only be replaced by a qualified

service engineer. There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of the used battery in accordance with the manufacturer's instructions.

• Using any battery pack, AC adapter, Vehicle power adapter (option) or accessory not

specified by the manufacturer for use with this phone creates a potential safety hazard.

• The earpiece may become warm during normal use and the unit itself may become

warm during charging.

• Use a damp or anti-static cloth to clean the phone. Do NOT use a dry cloth or

electrostatically charged cloth. Do not use chemical or abrasive cleaners as these could damage the case.

• Remember to recycle: the cardboard packaging supplied with this phone is ideal for

recycling.

• Do not leave the battery pack empty or disconnected for a long time, otherwise some

data may be initialized.

• Your phone contains metal which may cause you an itch, a rash or eczema depending

on your constitution or physical condition.

• Take care not to put your phone in the back pocket of your trousers or skirt and then

sit on it. Also, do not put your phone at the bottom of bag where it may subject to excessive weight or pressure. Doing so may damage the LCD and camera lens and cause them malfunction.

• Take care not to hold the Light too close to your or other people’s eyes when the Light

is lit.

• The foam covers the earpiece of the headset. Do not put any other part of the headset

in your ears.

Aircraft Safety

• Switch off your phone and remove its battery when inside or near aircraft. The use of

cellphones in aircraft is illegal. It may be dangerous to the operation of the aircraft and it may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellphone service to the offender, or legal action, or both.

• Do not use your phone on the ground without the permission of the ground crew.

Hospital Safety

• Switch off your phone in areas where the use of cellphones is prohibited. Follow the

instructions given by the respective medical facility regarding the use of cellphones on their premises.

General Safety

• Observe ‘Turn off 2-way radio’ signs, such as those near stores of fuel, chemicals or

explosives.

• Do not allow children to play with the phone, charger or batteries.

• Small parts are included in your phone. Keep them out of reach of small children, for

whom it could be a choking hazard.

• The operation of some medical electronic devices, such as hearing aids and

pacemakers, may be affected if a cellphone is used next to them. Observe any warning signs and manufacturer's recommendations.

• If you have a weak heart, you should take extra precautions when setting functions

such as the Vibrator and Ringer volume functions for incoming calls.

• If you set the Vibrator setting to anything other than OFF, be careful that the phone is

not near a source of heat (e.g. a heater) and that it does not fall from a desk due to the vibration.

Road Safety

• You MUST exercise proper control of your vehicle at all times. Give full attention to

driving.

• Observe all the recommendations contained in your local traffic safety documentation.

• Pull off the road and park before making or answering a call if driving conditions so

require.

• You MUST NOT stop on the hard shoulder of a motorway to answer or make a call,

except in an emergency.

Emergency Services and Safety Precautions

• Switch off your phone at a refuelling point, such as a petrol station, even if you are not

refuelling your own car.

• Do not store or ca rry flammable or explosive materials in the same comp artment where

a radio transmitter, such as a cellphone, is placed.

• Electronic vehicle systems, such as anti-lock brakes, speed control and fuel injection

systems are not normally affected by radio transmissions. The manufacturer of such equipment can advise if it is adequately shielded from radio transmissions. If you suspect vehicle problems caused by radio transmissions, consult your dealer and do not switch on your phone until it has been checked by qualified approved installers.

Vehicles Equipped with an Air Bag

An air bag inflates with great force. Do not place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Third Party Equipment

The use of third party equipment, cables or accessories, not made or authorized by NEC, may invalidate the warranty of your cellphone and also adversely affect the phone’s operation. For example use only the NEC mains cable supplied with the AC charger.

Service

The cellphone, batteries and charger contain no user-serviceable parts. We recommend that your NEC cellphone is serviced or repaired by an NEC authorized service centre. Please contact your Service Provider or NEC for advice.

Non-Ionizing Radiations

The radio equipment shall be connected to the antenna via a non-radiating cable (e.g. coax). The antenna shall be mounted in a position such that no part of the human body will normally rest close to any part of the antenna unless there is an intervening metallic screen, for example, the metallic roof. Use only an antenna that has been specifically designed for your phone. Use of unauthorized antennas, modifications or attachments could damage your phone and may violate the appropriate regulations, causing loss of performance and radio frequency (RF) energy above the recommended limits.

Efficient Use

For optimum performance with minimum power consumption, note the following:

• Your phone has the internal antenna. Do not cover part of the internal antenna of the

phone with your hands. This affects call quality, may cause the phone to operate at a higher power level than needed and may shorten talk and standby times.

Radio Frequency Energy

Your phone is a low-power radio transmitter and receiver. When it is turned on, it intermittently receives and transmits radio frequency (RF) energy (radio waves). The system that handles the call controls the power level at which the phone transmits.

Exposure to Radio Frequency Energy

Your phone is designed not to exceed the limits for exposure to RF energy set by national authorities and international health agencies. * These limits are part of comprehensive guidelines and establish permitted levels of radio wave exposure for the general population. The guidelines were developed by independent scientific organizations such as ICNIRP (International Commission on Non-Ionizing Radiation Protection) through periodic and thorough evaluation of scientific studies. The limits include a substantial safety margin designed to assure the safety of all persons, regardless of age and health, and to account for any variations in measurements.

*Examples of radio frequency exposure guidelines and standards that your phone is

designed to conform to:

• ICNIRP, “Guidelines for limiting exposure to time-varying electric, magnetic, and

electromagnetic fields (up to 300 G Hz)-International Commission on Non-Ionizing Radiation Protection (ICNIRP)”. Health Physics, vol. 74. pp, 494-522, April 1998.

• 99/519/EC Council Recommendation on the limitation of exposure to the general

public to electromagnetic fields 0 Hz-300 GHz, Official Journal of the European Communities, July 12,1999.

• ANSI/IEEE C95.1-1992. “Safety levels with respect to human exposure to radio

frequency electromagnetic fields, 3kHz to 300 GHz”. The Institute of Electrical and Electronics Engineers Inc., New York, 1991.

• FCC Report and Order, ET Docket 93-62, FCC 96-326, Federal Communications

Commission (FCC), August 1996.

• Radio communications (Electromagnetic Radiation Human Exposure) Standard 1999,

Australian Communications Authority (ACA), May 1999.

Declaration of Conformity

• This product complies with the requirements of the R&TTE Directive 1999/5/EC. The

‘Declaration of Conformity’ leaflet can be found within this box.

Disposing of your used NEC product

Licenses

• T9

Text Input and the T9 logo are registered trademarks of Tegic Communication. “T9 Text Input is licensed under one or more of the following: U.S. Pat. Nos. 5,187,480, 5,818,437, 5,945,928, 5,953,541, 6,011,554, 6,286,064, 6,307,548, 6,307,549, and 6,636,162, 6,646,573; Australian Pat. Nos. 727539, 746674, and 747901; Canadian Pat. Nos. 1,331,057, 2,302,595, and 2,227,904; Japan Pat. No. 3532780, 3492981; United Kingdom Pat. No. 2238414B; Hong Kong Standard Pat. No. HK1010924; Republic of Singapore Pat. No. 51383, 66959, and 71979; European. Pat. Nos. 0 842 463 (96927260.8), 1 010 057 (98903671.0), 1 018 069 (98950708.2); Republic of Korea Pat. Nos. KR201211B1 and KR226206B1. People’s Republic of China Pat. Application Nos. 98802801.8, 98809472.X and

96196739.0; Mexico Pat. No. 208141; Russian Federation Pat. No. 2206118; and additional patents are pending worldwide”

• USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG-4

VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE DIRECTLY RELATED TO

•In the European Union

EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes mobile telephones or electrical accessories, such as chargers or headsets. When you dispose of such products, please follow the guidance of your local authority and/or ask the shop where you purchased the product. The mark on the electrical and electronic products only applies to the current European Union Member States.

•Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority and ask for the correct method of disposal.

Emergency Services and Safety Precautions

(A) DATA OR INFORMATION ENCODED BY A CONSUMER FOR PERSONAL AND NON-COMMERCIAL USE WITHOUT REMUNERATION; (B) DATA OR INFORMATION (i) GENERATED BY AND OBTAINED WITHOUT CHARGE FROM A CONSUMER NOT THEREBY ENGAGED IN A BUSINESS ENTERPRISE, AND (ii) FOR PERSONAL USE ONLY; AND (C) OTHER USES SPECIFICALLY AND SEPARATELY LICENSED BY MPEG LA, L.L.C.

• Helvetica is a registered Trademark of Heidelberger Druckmaschinen AG which may

be registered in certain jurisdictions.

• Java and all Java-based trademarks and logos are trademarks or registered

trademarks of Sun Microsystems, Inc in the U.S. and other countries.

• This product contains ACCESS Co., LTD’s Compact NetFront™ Plus internet browser

Compact NetFront™ is a registered trademark or trademark of ACCESS CO., LTD in Japan and selected countries worldwide.

• This product contains ACCESS CO., LTD’s JV-Lite2™ Java virtual machine software.

• Proprietary notice contains Macromedia Flash™ Player technology by Macromedia,

Inc., Copyright © 1995-2005 Macromedia, Inc. All rights reserved. Macromedia, Flash and Macromedia Flash are trademarks or registered trademarks of Macromedia, Inc. in the United States and other countries.

This product features the Macromedia Flash™ Player technology. For further information on the Macromedia Flash Player, visit http://www.macromedia.com/ software/flash/about/.

• This Mobile Printing Ready product is designed to provide easy printing from mobile

phones. This product follows Mobile Imaging and Printing Consortium (MIPC) guidelines version 1.0 for PictBridge.

• The Bluetooth

use of such marks by NEC is under license. Other trademarks and trade names are those of their respective owners.

• i-mode and i-mode logos are trademarks or registered trademarks of NTT DoCoMo.

For the purpose of improvement, the specifications for this product and its accessories are subject to complete or partial change without prior notice.

word mark and logos are owned by the Bluetooth SIG, Inc. and any

Emergency Services and Safety Precautions

iii

Before You Start

▼

User’s manual conventions

The instructions in this user’s manual make use of the shortcuts selection except special cases.

The following markers are used throughout the user’s manual to attract your attention:

/ This type of paragraph will contain details of where to find information related to the topic in question.

2 This type of paragraph will contain information worth noting.

, This type of paragraph will contain important information.

☛ This type of description will contain procedures to operate your phone.

Menu shortcuts selection

The alternative shortcuts method of selection lets you jump straight to a menu or function without highlighting an icon and scrolling through the intermediate menu options. The selection is made by pressing numbers which relate to the displayed menu options.

2 The instructions in this user’s manual make use of the shortcuts selection, except in special cases.

Reading the titles

Some titles in this manual contain information on how to access the functions. In these titles, M stands for , the numbers indicate the menu shortcut numbers (see “Overview of menu function” on page xi for details) and ... (three periods) indicate that there are more operations described in the paragraph.

Reading the procedures

“Highlight” means to use the 4-way navigation keys (▲▼ ) to move the area emphasized with different colouring. “Select” means to highlight an item and then press Procedures are written omitting the verb “press”, except in some special cases. For example, 1 2 means to:

☛ Start from the standby screen ➔ Press to display the Main menu screen ☛ Press 1 to display the Settings screen ➔ Press 2 to display the Phone modes screen

Simple procedures are connected by arrows (➔).

Check box/Radio button

A check box enables/disables an option out of a set of options, and multiple check boxes can be selected at the same time. On the other hand, selecting a radio button automatically cancels the previous selection, so only one radio button can be selected at one time.

A check box/radio button option can be selected/cancelled by highlighting it and pressing .

▼

Before You Start

Display information

▼

Menu title

Desktop icon area

This area contains the automatically displayed and the manually created desktop icons. They provide shortcuts to certain items/functions.

Help area

This area contains clock information and help information appropriate for the current screen (e.g. key presses remaining when composing a message).

, The Liquid Crystal Displays (LCD) on your phone are manufactured using high-precision technology. Even so, the LCD may contain pixels

(dots) that fail to light or that remain permanently lit. Note that this is normal and does not indicate a problem with your display.

SK1/SK2

This area contains context sensitive descriptions of the Softkeys’ functions appropriate for the current screen.

Status bar area

This area contains icons which indicate the battery strength, new SMS/MMS message(s), signal strength, etc. (see page viii).

Shortcut number

Press the appropriate number to jump straight to a next menu. The row colour is changed when selected (e.g. to activate/ deactivate a facility).

Help icons

Displayed when you can use the key represented by these icons (see page viii).

Shortcut menu number

The current menu number is displayed.

Page scroll bar

Displayed when you can press to scroll to the next page.

Next menu icon

Displayed when you can press or the shortcut number to show the next menu.

▼

Before You Start

Parts and functions

▼▼▼

Speaker

Earpiece

Main-LCD

Through-hole

for straps

Earphone jack cover

Side up key

Side down key

4-way navigation key

(

▲▼

W X

Softkey1(SK1)

Menu ( ) key

Clear (CLR)/Back key

Send ( ) key

)

Internal antenna

Softkey2(SK2) Select key

( )

Phonebook ( )key

End/on-off ( ) key

Alphanumeric keys

Mouthpiece

Charger connector cover

, Be careful not to put your finger or foreign objects in the hinge of the phone when your phone is opened.

4-way navigation key and select key

In this user’s manual, ▲▼ and symbols are used to represent the 4-way navigation key (Up, Down, Left or Right key) and Select key.

Symbols used in the user’s manual

Symbols on the keys

Before You Start

▼

Up key Down key Left key Right key Select key

▲▼

2nd-LCD

LED & light

Camera

Rear cover

for battery

Keypad shortcuts

▼

The following operations are available from the standby screen.

Key Operation that involves pressing a key

Accessing the Main menu screen xi Setting/Cancelling the Side key lock 20

SK1 Accessing the Mail screen 43 Accessing the Inbox screen 44

SK2 Accessing the i-mode menu screen 40 Accessing the Java™ applications screen 68

Accessing the Phonebook list screen 49 Accessing the Message screen 27

▲ Accessing the Phone modes screen 21 Setting the phone to Meeting mode/Returning to the previous mode 21

▼ Accessing the My data screen 61 Accessing the voice recall 8

▼

Accessing the received calls list 12 – –

Accessing the missed calls list 12 – –

Accessing the dialled calls list 12 – –

Highlighting a desktop icon 19 Accessing the homepage 41

Ending a call or returning to the standby screen – Powering off 5

Cancelling the Cell Broadcast message display 33 Deleting all the automatically displayed desktop icons 18

CLR

Deleting character or returning to the previous screen – Deleting all characters when you enter text –

1 Entering phone numbers 5 Calling the Voice mail centre 55

2 to 9 Entering phone numbers 5 One-touch dial to the corresponding number in the phonebook(SIM) 7

0 Entering phone numbers 5 Entering + when you make an international call 14

# Entering # 5 Entering a pause –

Entering

Accessing the volume control screen when your phone is open (Use ▲ ▼, Side keys or 0 to 9 keys to adjust the volume.)

Side up

Activating the ring silencer function when you receive a call 20

Accessing the volume control screen when your phone is open

Side down

(Use ▲ ▼, Side keys or 0 to 9 keys to adjust the volume.)

Activating the ring silencer function when you receive a call 20

See

page

5 Switching the ALS line 1/2 (if the SIM card supports ALS) 20

Operation that involves pressing and holding a key

Accessing the camera view finder screen 56

Turning on the light (To turn it off, press any key or open/close your phone.)

See

page

–

Before You Start

vii

LCD and displayed icons

Main-LCD

Indicates the battery level.

Indicates the battery charging status (fast, slow, stop).

Indicates that there is a new SMS in your phone.

Indicates that there is a new SMS on the network.

Indicates that the SIM memory is full.

Indicates that the Inbox in your phone is full.

(pink)

Indicates that there are mail and MMS on the server.

Indicates that there is a new mail/MMS in your phone.

(yellow)

8 9

2 This yellow icon blinks while a mail/MMS is being

downloaded.

Indicates that the memory for mail/MMS is full.

(red, green/red, green)

Indicates that new voice mail messages are on the network (No ALS or ALS Line 1/ALS Line 1 and 2/ALS Line 2).

Indicates secured communication on WTLS in imode browsing.

Indicates that your phone is connected to a GPRS/EDGE modem such as PC.

(gray)

Indicates that the phone is in the GSM (Global System for Mobile communication) network service area and GPRS/EDGE is active.

(yellow)

Indicates that the GPRS/EDGE is available and i-mode (PDP Context) is active.

Indicates that the i-mode connection is carried out.

Indicates that the i-mode lock is on.

2 No icon appears when the phone is outside the

GSM network service area, or when the phone is in the GSM network service area and GPRS

EDGE is not attached.

Indicates that Bluetooth is set to on, Bluetooth is in operation.

Indicates the line status (No ALS or ALS Line 1/ ALS Line 2). The icon with displayed in red

indicates that the ALS line 1 or 2 is unencrypted/ no ALS.

Indicates the signal strength level.

Appears when you are outside the service area.

Network name (indicated in orange when using

roaming service)

Desktop icons

See “Desktop icons” on page 18 for details

Indicates the call diversion is set.

Indicates the Meeting mode, Pocket mode, Car mode.

2 No icon appears for the Normal mode.

Indicates sound-off, vibrator-on, sound-off/ vibrator-on.

Indicates alarm-on.

Indicates the auto start of a Java™ application has failed.

Date

Day of week

Remote time

Local time

16 17

Indicates that you can use the options menu by pressing .

Indicates that you can use the phonebook list by pressing .

Before You Start

viii

Indicates the usable keys in black, while using imode or a Java™ application is in operation.

Indicates that the help display is available by pressing when using SIM toolkit.

Indicates that a Java™ application is in operation.

<When the camera/video view finder is in

operation>

Indicates single/burst mode (camera).

Indicates the video mode is on or the video is recording.

Indicates that the self timer is on.

Indicates the quality of the picture (super fine, fine, normal, economy or super economy).

Indicates the quality of the video.

Indicates the photo/video screen size.

Indicates the shooting environment.

Indicates the brightness setting. The “+2” setting is the brightest.

Indicates the zoom level.

Indicates the video is playing, on pause, stopped, fast forwarding, or rewinding.

Indicates the video is being downloaded and replayed (progressive download).

2 This icon blinks while buffering, pausing, or

stopping the download.

Indicates the video is played in normal/enlarged screen size.

Displays the current volume level. The 0 is mute and 9 is the maximum.

<When the streaming video player is in

operation>

Indicates the video is playing, on pause, stopped.

Indicates the video type is on-demand (stored on a server and played by your request) or broadcast (currently broadcasted on a server).

(red, yellow, green)

Indicates the amount of buffered data. (The colour of icon changes in order from red to yellow to green as buffering progresses.)

Indicates the video is played in normal/enlarged screen size.

Displays the current volume level. The 0 is mute and 9 is the maximum.

Displays the current volume level. The 0 is mute and 9 is the maximum.

Indicates the repeat mode is Repeat all, Repeat one.

Indicates the Equalizer mode is Rock, Jazz, Pop

Indicates the repeat mode is Repeat all, Repeat one.

Displays the current volume level. The 0 is mute and 9 is the maximum.

Before You Start

2nd-LCD

Indicates the battery level.

Indicates

the battery charging status (fast, slow,

stop).

Indicates that there is a new SMS in your phone.

Indicates

that there is a new SMS on the network.

Indicates that the SIM memory is full.

Indicates that the Inbox in your phone is full.

(pink)

Indicates that there are mail and MMS on the server.

(yellow)

Indicates that there is a new mail/MMS in your phone.

2 This yellow icon blinks while a mail/MMS is being

downloaded.

Indicates that the memory for a mail/MMS is full (red, green/red, green)

Indicates that a new voice mail message is on the network (No ALS or ALS Line 1/ALS Line 1 and 2/ALS Line 2).

Indicates the Bluetooth is on, Bluetooth is in active.

Indicates the signal strength level.

Appears when you are outside the service area.

Indicates that the phone is in the Meeting/Pocket/ Car mode.

2 No icon appears for the Normal mode.

<When 2nd-LCD is used as the camera view

finder screen>

Indicates the battery level.

Indicates stop).

Indicates single or burst mode of the camera.

Indicates that the video mode is on or the video is recording.

Indicates the photo/video screen size.

Indicates that the self timer is on.

<When the Music player/MP3 player is in

operation>

Indicates the player is playing, stopped.

Indicates the repeat mode is Repeat all, Repeat one.

213 4 65

the battery charging status (fast, slow,

(blue, red)

Before You Start

Overview of menu function

▼

Standby screen

➡

CLR

Main menu screen

➡

The Main menu has a set of icons for its top levels of options which can be selected either using a combination of the 4-way navigation key (▲ ▼

▼

) and (menu selection),

or just the keypad (shortcuts selection).

2 The title of the selected option will be displayed in the Help area. 2 SIM toolkit icon is displayed only when your SIM card supports this function. 2 With the Main menu screen displayed, 0 to display your own number.

Key Main menu Second level menu

1 Settings Phone

Phone modes Main-LCD 2nd-LCD Power saving Calls Security Network Reset settings

2 Message Inbox

Drafts Outbox Sent Folder1 Folder2 CB

Key Main menu Second level menu

3 i-mode i-mode

Settings

4 Phonebook Lists

Information # Call options

5 Camera Camera

Video recorder

6 My data Videos

Sounds Pictures MP3

Key Main menu Second level menu

7 Java Programs

Prog backlight

8 Accessory Music player

MP3 player Calculator Clock alarm Scheduler ToDo list Notepad Voic e me mo Currency Bluetooth Synchronization

9 SIM toolkit

Before You Start

Getting Started 1

Basic Calls & Phone Use 5

Text Entry 15

Desktop icons 18

Settings (M1) 20

Message (M2) 27

i-mode (M3) 34

Phonebook (M4) 49

Camera (M5) 56

My data (M6) 61

Java™ (M7) 68

Accessory (M8) 69

Bluetooth (M80) 79

Index 84

Emergency Services and Safety Precautions i

Before You Start iv

User’s manual conventions............................................. iv

Display information .......................................................... v

Parts and functions ......................................................... vi

LCD and displayed icons ...............................................viii

Overview of menu function ............................................. xi

Getting Started 1

Preparing the phone ........................................................1

Standby and talk times..................................................... 4

Checking the battery ........................................................4

Low battery alarm ............................................................4

Other battery alarms ........................................................4

Start-up ............................................................................4

Basic Calls & Phone Use 5

Making basic calls............................................................5

Ending a call ....................................................................6

Receiving an incoming call ..............................................6

Unsuccessful calls ...........................................................7

Emergency calls............................................................... 7

Last number redial ...........................................................7

One-touch dial.................................................................. 7

Fast dialling......................................................................7

Displaying your own phone number (M0/M416) ..............8

Voice recall ......................................................................8

Options menu (during a call) ............................................ 8

Putting a call on hold........................................................ 9

Mute .................................................................................9

Call transfer...................................................................... 9

Multi-party calls ................................................................ 9

Recording a call ............................................................. 10

Scratchpad number........................................................ 10

Call options (M43)..........................................................11

Call settings (M16) ......................................................... 12

International dialling codes ............................................14

Roaming......................................................................... 14

Text Entry 15

Mode change ................................................................. 15

English text input ....................................................15

Normal text input............................................................16

Numeric input.................................................................17

Key allocations............................................................... 17

Desktop icons 18

Settings (M1) 20

Phone (M11) .................................................................. 20

Phone modes (M12) ......................................................21

Main-LCD (M13) ............................................................23

2nd-LCD (M14) .............................................................. 23

Power saving (M15) ....................................................... 23

Calls (M16)..................................................................... 24

Security (M17)................................................................ 24

Network (M18) ...............................................................25

Reset settings (M19)......................................................25

Message (M2) 27

Message overview .........................................................27

Contents

xiii

Reading a message (M21) ............................................ 28

Creating a message....................................................... 32

Cell broadcast (M27) ..................................................... 33

i-mode (M3) 34

i-mode operation guide .................................................. 34

i-mode screen ................................................................ 39

i-mode menu screen ...................................................... 40

iMenu screen .................................................................42

Browser Options menu ..................................................43

Mail screen .................................................................... 43

i-mode glossary ............................................................. 47

Phonebook (M4) 49

Phonebook types ........................................................... 49

Accessing your phonebook (M4) ...................................50

Phonebook list Options menu........................................ 50

Personal data Options menu .........................................54

Voice mail (M417).......................................................... 55

Camera (M5) 56

Notes on using the camera............................................ 56

Taking a picture (M51)................................................... 57

Recording a video (M52) ............................................... 59

My data (M6) 61

Videos (M61) ................................................................. 62

Sounds (M62) ................................................................62

Pictures (M63) ............................................................... 63

MP3 (M64) ..................................................................... 65

File selector Options menu ............................................ 65

Java™ (M7) 68

Programs (M71)............................................................. 68

Prog backlight (M72)...................................................... 69

Accessory (M8) 69

Music player (M81) ........................................................ 69

MP3 player (M82) .......................................................... 70

Calculator (M83) ............................................................ 71

Clock alarm (M84) ......................................................... 72

Scheduler (M85) ............................................................ 73

ToDo list (M86) .............................................................. 74

Notepad (M87)............................................................... 76

Voice memo (M88) ........................................................ 77

Currency (M89).............................................................. 77

Bluetooth (M80) ............................................................. 78

Synchronization (M8*) ................................................... 78

Bluetooth (M80) 79

Pairing a Bluetooth device and your phone ................... 80

Using Bluetooth for voice/modem.................................. 81

Bluetooth file transfer..................................................... 81

File browsing service ..................................................... 83

Index 84

xiv

Contents

Getting Started

Preparing the phone

Before trying to use your phone, make sure that a valid Subscriber Identity Module (SIM) card is inserted and the battery is charged.

SIM card

Before using your phone, you must sign-up with one of the digital network service providers. In addition to your subscription details you will receive a personal SIM (Subscriber Identity Module) card which is inserted into your phone.

If the SIM card is removed, the phone becomes unusable until a valid SIM card is fitted. It is possible to transfer your SIM card to another compatible phone and resume your network subscription. The screen on your phone will display appropriate messages if no SIM card is fitted.

, If the phone, or the SIM card, is lost or stolen then you should contact your service provider immediately in order to bar it from use.

2 The phone supports a number of languages and the keyboard symbols have been chosen for world-wide operation. 2 The digital technology of your phone helps to ensure that your conversations are kept secure. 2 The SIM card contains personal data such as your electronic phonebook, messages (see “Message (M2)” on page 27) and also details of the network

services you have subscribed to. The phone will not work (except for emergency calls on some networks) unless a valid SIM card is fitted.

, Be sure to turn the phone off before inserting and removing a SIM card. Otherwise damage to the SIM card can occur.

Inserting a SIM card

, Be sure to turn the phone off before removing the battery pack.

☛ While pressing down the areas marked with of the rear cover as indicated by arrow ➀, slide the rear cover about 3 mm in the direction of

arrow ➁ with your finger tip. Then, lift the cover up in the direction of arrow ➂ to remove it.

☛ Lift the finger tab of the battery pack up in the direction of arrow ➃. Then lift the battery pack out in the direction of arrow ➄. ☛ With the metal part facing down, insert the straight end of the SIM card under the holder in the direction of arrow ➅. Slide the SIM card all the way

until it reaches the end.

, Be careful not to damage electric parts of the SIM holder when inserting a SIM card.

☛ Insert the two tabs on the battery pack into the slots on the phone in the direction of arrow ➇, making sure that the tabs on the battery pack fit

properly into the slots on the phone. Then, press the battery pack down in the direction of arrow ➈ to clip it into the phone.

, Make sure that the battery pack is securely attached to the phone and align the rear cover with the grooves on the phone so that there is a gap

of about 3 mm at the end of the cover. After making sure that there is no gap between the rear cover and the phone body, slide the rear cover in the direction of arrow ➉ until you hear a click.

Getting Started

Rear cove

Battery

Finger tab

Slots

Tabs

Holde

out 3 mm

SIM card

, If the SIM card is not fully inserted when the battery is replaced, damage to the SIM card can occur.

/ If the SIM card is already fitted, see “Start-up” on page 4.

Removing a SIM card

☛

With the battery removed, push the short and straight end of the SIM card with your thumb to slide it gently in the direction of arrow ➆ ➔ Lift the SIM card after it is completely removed from the holder.

, Be careful not to damage electric parts of the SIM holder when removing a SIM card.

Getting Started

bout 3 mm

Check that there is no gap between the rear cover and the phone body.

Charging the battery

Before trying to use your phone, insert the phone’s battery, and connect the NEC battery charger (AC adapter) supplied with your phone to a suitable mains power socket.

☛ Pull open the charger connector cover gently.

, Be careful when handling the charger connector cover. Do not pull strongly.

☛ With the arrow marks of the charger plug facing up, hold the buttons on both sides of

the charger plug with your thumb and index finger.

Charger connecto

☛ Press the buttons as indicated by the arrow marks on the charger plug and insert the

plug into the charger connector.

, Make sure to insert the charger plug with the arrow marks facing up. Otherwise,

damage to the charger connector can occur when disconnecting the charger plug.

2 If your phone is turned on and charging starts, the battery charging icon will be

displayed. LED will turn on in red while charging. When charging is complete, the LED will turn off.

rrow marks

PressPress

Charger plug

2 You are recommended to switch off the phone while charging. If you need to receive

calls, your phone can be switched on and left in standby while being charged, although the total time taken to charge is then increased.

☛ After the charging is complete, press the buttons of the charger plug as indicated by

the arrow marks on the charger plug (➀) and gently pull straight out of the charger connector (➁).

Charger connecto

PressPress

Charger plug

, Make sure to press both buttons when disconnecting the charger plug from the

charger connector. If you pull the charger plug forcibly without pressing the buttons, damage to the charger connector can occur.

The icons show the charging status of battery.

Fast battery charging Slow battery charging while the phone is in use Battery charging stopped due to overheat

, Using any battery pack, AC adapter, vehicle power adapter (option) not specified by NEC for use with this phone can be dangerous and

may invalidate any warranty and approval given to the cellphone. Do not leave the charger connected to the mains supply when it is not in use.

, Do not try to charge the battery if the ambient temperature is below 5°C (41°F) or above 35°C (95°F). , DO NOT connect a charger or any other external DC source until the phone’s battery is inserted.

2 If the phone does not respond, please wait for a few minutes. The charging will then start. 2 If you use the phone while charging, handle the phone carefully since the cable or adapter is connected. 2 If you make/receive a call while charging, the charging may temporarily be interrupted. 2 Charging takes approximately 3 hours with your phone turned off. 2 Even if the phone remains connected to the charger, battery residual capacity may decrease when the phone is used for video recording, playing or

other battery consuming operation.

Getting Started

, IMPORTANT BATTERY CHARGING INFORMATION

Charging a very low battery

The battery’s charge continues to drop after the low battery warning is displayed. In extreme cases where the battery is left uncharged for some considerable time after this warning, a trickle charge is used to slowly top-up the battery to the safe level at which the fast charging can begin. The phone can be in trickle charge for a few minutes before the fast charging starts.

Standby and talk times

Your phone works closely with the network you are using to provide the services you need, and the standby and talk times achieved will depend on how you use the phone and choices made by the network operator.

In particular, factors such as your location within the network, the frequency at which this location is updated, the type of SIM card you have, your reception of area messages or cell broadcast messages and the use of full rate or enhanced full rate speech, will affect both standby and talk times.

Checking the battery

☛ Check icon at the top of the standby screen.

The number of blocks on the icon shows the charge of your battery pack.

Full battery power Partial battery power Low battery power Battery empty

Low battery alarm

When the battery voltage falls below the working level, a low battery warning is displayed on the screen accompanied by LED illumination and a short tone along with an empty battery icon. The phone will automatically power down shortly afterwards.

2 Please charge the battery as much as possible when the battery is very low.

Other battery alarms

Your phone may display warnings when the battery temperature is too high, or the voltage of the battery or the charger is over the appropriate level. Follow the instruction given by these warnings immediately.

Start-up

Switching the phone on

☛

Hold down for about a second to switch on. The screen will display the selected greeting (if set, see page 23) and the phone is then in standby.

2 You may need to charge the battery before using your phone. 2 When your phone is turned on, the specified ringer may sound.

Getting Started

2 If your phone is accidentally turned off while downloading or deleting Java™ application, it will take longer than usual to start up the phone the next

▼

time you turn on the power.

Switching the phone off

☛ Hold down until the display shows the switch off message.

PIN code

The SIM card issued by your service provider has a security feature called PIN code protection. The Personal Identification Number (PIN) is a number put on to the card by your service provider, and is 4 to 8 digits long. Some service providers supply SIM cards which will cause your phone to prompt for a PIN code when it is turned on. If this is the case, enter your code with the phone’s keypad. If you insert a SIM card other than your own, information such as call logs may be lost (see “Security (M17)” on page 24 for details).

Basic Calls & Phone Use

Making basic calls

You make a simple call in the same way as you would with a normal phone, except that you need to press after entering the area Subscriber Trunk Dialling (STD) code and the phone number. To make international calls, you must first enter the international dialling code (see page 14).

2 Use the full STD area code even if you are calling to a person in the same town. If the numbers are too long to be displayed within one line, after

pressing , excess part is deleted and ‘...’ is added at its end.

2 The main-LCD display shows the strength of the radio signal that links your phone to the network. The maximum signal strength is shown by 4 shaded

blocks and the minimum signal strength by 1 block.

Starting a call

☛

Key in the phone number. Check the number on the display ➔ or SK1 to send the input number to start the call

☛ Before the other party answers the call, you can end the call by pressing briefly, pressing SK2 or closing your phone. When you use the

headset, you can also end the call by pressing and holding the button on it.

2 When connecting a wired headset and Bluetooth headset at the same time, the wired headset will work partially (only its button will work).

When the call is sent, the screen displays the number called, the name stored in the phonebook and a connection graphic or a Calling Line Identification (CLI) picture that has been allocated to the number called (see page 53).

Correcting mistakes

▼

Use the and to move the cursor and then CLR to clear individual digits, or hold down CLR to completely clear a phone number.

Basic Calls & Phone Use

Ending a call

☛ While talking, SK2 or briefly, or close your phone. The phone returns to the standby screen.

2 If is held down, your phone will turn off. 2 When you use the headset, you can also end a call by pressing and holding the button on it. 2 When connecting a wired headset and Bluetooth headset at the same time, the wired headset will work partially (only its button will work). 2 You cannot end a call by closing your phone when the headset is connected.

Receiving an incoming call

When someone calls your number, the ringer will play (if set - see page 22), the LED glows in the specified colour, and the phone number of the caller may be displayed if the calling line identification facility is available and the caller has activated the feature. If the caller’s phone number has been related and stored in your phonebook with a name and a CLI picture (see page 53), that name and picture will be displayed. If the caller has withheld their identity, the screen will give a message that the caller’s number is being withheld. If the origin of the call cannot be determined, no information is displayed on the screen.

2 You also have options for holding and forwarding calls. These options depend on your network and your subscription arrangements. 2 When connecting a wired headset and Bluetooth headset at the same time, the wired headset will work partially (only its button will work).

Accepting an incoming call

☛

While receiving an incoming call, or SK1

2 When you use the headset, you can also accept an incoming call by pressing the button on it. 2 When Auto answer function (see page 22) is set to on and a headset is connected to the phone, the incoming call is automatically accepted after

several rings.

2 You can accept an incoming call by opening your phone, when Fold answer function (see page 20) is set to on. 2 You can set your phone to answer a call when any key is pressed (see “Any key answer” on page 20).

Rejecting an incoming call

☛ While receiving an incoming call, or SK2 briefly or close your phone.

2 When you use the headset, you can also reject an incoming call by pressing and holding the button on it. 2 You cannot reject a call by closing your phone when the headset is connected.

If your phone receives a call and you do not answer it, the main-LCD will display a desktop icon of the phone number (or the name if stored) of the caller (if available).If your phone is closed, the 2nd-LCD will also display a missed call icon, and you can display the details by pressing Side up. This information is stored in the missed calls list. Up to 20 missed calls are stored in this list.

2 If you are making a call, the phone gives priority to receiving a call unless you have already pressed .

/ See also: “Call diversion (M161)” on page 12 and “Call waiting and holding (M162)” on page 13.

Basic Calls & Phone Use

/ See also: “Call options (M43)” on page 11.

Unsuccessful calls

If dialled call is not successfully connected, the display will give an appropriate message. If your phone has the auto redial function activated, the number will be automatically called again after a short delay (see page 13).

Emergency calls

The standard emergency number of 112 can be used.

☛ Key in 1 1 2 ➔ or SK1 to connect the call to the local emergency services.

2 On some networks, emergency calls can be made using the 112 number without a SIM card inserted.

Last number redial

You can redial the last number you called.

☛ Ensure that the standby screen is displayed and no phone number is shown ➔ twice to dial the last number you called.

/ See also: “Call options (M43)” on page 11.

One-touch dial

One-touch dial for the phonebook (SIM) is available by pressing and holding the number keys between 2 and 9.

2 A number for the One-touch dial corresponds to the location number in the phonebook (SIM). 2 One-touch dial is available only for the phone numbers with the location number 2 to 9 stored in the phonebook (SIM).

Fast dialling

You can make a call to the phone number in the phonebook (Phone/SIM) with just a few press of button. To fast-dial the phone number in the phonebook (SIM), use the following procedure:

☛ From the standby screen, key in the Location number of a personal data in the phonebook (SIM) ➔ #. The corresponding personal data is

displayed.

☛ to dial the phone number.

To fast-dial the phone number in the phonebook (Phone), use the following procedure:

☛ From the standby screen, key in the Abbreviated Dialing Number (ADN) of a personal data in the phonebook (Phone) ➔ . The corresponding

personal data is displayed.

Basic Calls & Phone Use

☛ Use the and keys to choose the phone number (if there are more than one), then to dial the phone number.

▼

Displaying your own phone number (M0/M416)

☛ 0 or 4 1 6

Voice recall

You can store up to 10 voice recall recordings which can be allocated to a personal data stored in the phonebook (Phone). To store the voice recall sound, see page 53. To use the voice recall function, use the following procedure:

☛ Press and hold ▼

2 When you use the headset, you can also activate the voice recall function by pressing and holding the button on it from the standby screen.

☛ Within 4 seconds, say the word or words you have recorded to identify the record you wish to recall. If the word or words were recognized, the

first phone number of the personal data stored in the phonebook (Phone) will be called automatically.

Options menu (during a call)

☛ During a call, to display the options menu

No. Options menu (during a call)

1 Main menu Displays the Main menu screen. See “Overview of menu function” on page xi for details.

2 Hold/Retrieve Puts the call(s) on hold or retrieves the call(s).

3Mute/Unmute Mutes or unmutes your voice to all active calls.

4 Transfer call Enables to transfer the call and connect other parties.

5 Add to conference Merges calls and makes a multi-party call.

6 Private call Make a private call to the highlighted party within the multi-party call.

7 Record call Records the call while talking.

8 Disconnect party Disconnects the highlighted party.

9 Switch call to Bluetooth/

Switch call to phone

0 Bluetooth On Activates the Bluetooth device.

2 After transferring the call, your call will be dropped.

Switches the audio path state of the call.

2 You can also switch call to Bluetooth or phone by pressing and holding #. 2 This option is available only when the Bluetooth device is connected to the phone.

Basic Calls & Phone Use

2 Depending on the conditions, some options may be displayed in gray and not be available.

Putting a call on hold

☛ To put the received or dialled call on hold, SK1 or 2. To retrieve the call, SK1 or 2 again.

Mute

You can mute the sound from the mouthpiece during a call. When your call is muted, the other party cannot hear any sound from your phone, but you can still hear the sound from the other party.

☛ To mute the sound during a call, 3. To retrieve the sound, 3 again.

2 The mute function is automatically released after the call ends. 2 The mute function is not available while using the headset.

Call transfer

When you have an active call and a held call, you can transfer the call and connect the two parties, then you can drop from the line while leaving those two calls active.

☛ To transfer the call, 4.

2 After dropping from the call with the other two parties, if you have a call waiting, you can proceed the call with it.

, Call transfer facility is SIM dependent.

Multi-party calls

If your SIM card is multi-party enabled, you can make a conference call to more than one caller. To create the multi-party calls, at least 3 parties, including the host, are needed.

Receiving the second call

☛ SK1 or to accept the second call ➔ SK2 or 5 to merge both calls to initiate a multi-party call.

2 When you accept the second call, the first call will be put on hold.

Making the second call

☛ SK1 to put the first call on hold ➔ Key in the phone number ➔ SK1 or to make the second call ➔ After the second participant answers, SK2

or 5 to merge both calls to initiate a multi-party call.

Basic Calls & Phone Use

Putting the multi-party calls on hold

☛

SK1 or 2 to put all calls on hold ➔ To retrieve the call, SK1 or 2 again.

2 You can put the multi-party calls on hold only when you are a host of the multi-party calls.

Making a private call

While on the multi-party call, you can make a private call to a specific party.

☛ To make a private call, highlight the desired party you want to make a private call to ➔ 6 ☛ To end a private call and return to the normal multi-party call ➔ 5

2 While you are on a private call, other parties can continue with their conversation. 2 You can make a private call only when you are a host of the multi-party calls.

Ending the multi-party calls

☛

To end the multi-party calls, or SK2.

☛ To disconnect a specific party on a multi-party call, highlight the party you wish to disconnect ➔ 8

2 You can disconnect a specific party on the multi-party calls only when you are a host of the multi-party calls.

, Multi-party call facilities are network dependent.

Recording a call

You can record the conversation during the call.

☛ During a call, press and hold ▼ or 7 to display the Voice memo screen ➔ SK1 to start the recording ➔ SK1 to pause and SK2 to stop the

recording

2 To play the recording, see “Recording/playing voice memo or setting speaker” on page 77.

Scratchpad number

Your phone has a scratchpad facility that enables you to take down a phone number during a call and then make a call to it when you have finished. This scratchpad number can be stored in memory for future use.

Noting & calling a scratchpad number

☛

During a call, key in the number to be placed in the scratchpad. It will be shown on your phone’s screen ➔ when the call is finished. The number will still be displayed ➔ to dial the displayed number.

Basic Calls & Phone Use

Call options (M43)

▼

From Call options, you can display the list of missed, received and dialled calls, the duration of the last call made and all calls, charge information and the redial blacklist.

☛ 4 3 to display the Call options screen.

No. Call options

1 Missed calls Displays the list of missed calls. You can also access this function by pressing from the standby screen.

2 Received calls Displays the list of received calls. You can also access this function by pressing from the standby screen.

3 Dialled calls Displays the list of dialled calls. You can also access this function by pressing from the standby screen.

4 Last call duration Displays the duration of the last call made on your phone.

▼

☛ SK1 to reset the display to zero.

5 Total calls duration Displays the duration of the total calls made on your phone.

☛ SK1 ➔ 1 to reset the duration of the total dialled calls, 2 to reset the duration of the total received calls,

or 3 to reset the duration of all calls.

6Charge info Displays the charge information (Advice of Charge - AoC).

, The AoC facility is SIM card and network dependent.

2 To reset the display to zero, set the maximum charges or edit the unit price, you may be prompted to

enter the PIN2 code.

1 Total charge Displays the total charge.

☛ SK1 to reset the display to zero.

2 Maximum

charge

3 Unit price Displays the unit price.

7 Redial blacklist Accesses the numbers in the blacklist.

2 If dialled call is not successfully connected (e.g. number busy), the auto redial facility will be offered (see

page 13). If you have set auto redial and the call still fails, the number called will be added to the blacklist.

2 Depending on the conditions, some options may be displayed in gray and not be available.

Displays the maximum charge.

☛ Key in the maximum number of units allowed ➔ SK1

☛ Highlight the whole number (integer), the decimal number or the currency field

➔ Key in the required value for the whole number and decimal number fields.

For the currency field, key in the currency type using a maximum of three characters ➔ SK1

Basic Calls & Phone Use

Display missed/received/dialled calls Options menu (M431M/M432M/M433M)

▼

☛

or 4 3 1 for missed calls, or 4 3 2 for received calls, or or 4 3 3 for dialled calls.

▼

☛ Highlight a number in the list ➔

No. Missed calls/Received calls/Dialled calls Options menu

1 Call Calls the current number.

2 Create message Creates a new message to the highlighted phone number.

3 Add to phonebook Adds the current number to the phonebook.

☛ 1 to add it as a new personal data, 2 to add it to an existing personal data ➔ Press the appropriate

number for the storage destination ➔ Press the appropriate number for the phonebook data field to copy the current number to.

4 Delete one Deletes the current number.

5 Delete all Deletes all the numbers in the list.

6Info Displays information on the current number.

7 Add desktop icon Creates a desktop icon of the selected number.

8Items/Page Selects either to display 4 or 8 phone numbers in one screen.

2 Depending on the conditions, some options may be displayed in gray and not be available.

Call settings (M16)

From the Calls screen, you can change various call settings: the call diversion, call waiting and holding, auto redial and line identification.

Call diversion (M161)

Setting Call diversion

☛ 1 6 1 ➔ or to select the type of call you wish to divert from Speech, Data or Fax.

▼

2 There will be a delay while your phone checks its divert status with your network.

☛ Highlight one of the conditions ➔ When the phone number field of a divert condition is highlighted, either enter the phone number to divert to, or

delete any existing phone number.

☛ If you have made any mistake, highlight the appropriate field ➔ SK1 to clear any mistakes. ☛ If the settings are correct,

, There will be a short delay while the network sends the divert status of your phone. , There may be an additional charge for this service depending on your network.

Basic Calls & Phone Use

, There may be unavailable settings depending on your network.

Call diversion edit options menu

☛ Highlight the required edit field ➔

No. Call diversion edit options menu

1Copy Copies the number in the edit field.

2Paste Pastes the previously copied number.

3 Disable all Disables the numbers from all the fields.

4 Phonebook Displays the phonebook to insert a number in the edit field.

5 Add to phonebook Adds the number to the phonebook as a new personal data or saves the number in an existing personal data.

2 Depending on the conditions, some options may be displayed in gray and not be available.

Call waiting and holding (M162)

This facility informs you that another call is being made to your phone while an existing call is in progress.

Setting up call waiting

☛ 1 6 2 ➔ 1 1 to activate, 1 2 to deactivate the call waiting, or 2 to check the status of call waiting.

Using call waiting

☛ If you are on a call and another comes in, you will be alerted by a beep in the earpiece ➔ SK1 to accept the incoming call.

☛ To switch the calls, SK1 ☛ To merge the calls, SK2 (see “Multi-party calls” on page 9). ☛ To end the current call, ☛ To retrieve the held call SK1

Auto redial (M163)

With the auto redial facility, your phone will redial a number up to 10 times if the first attempt fails. A tone will be heard at each redial attempt. Your phone cannot connect a call if the other party is busy or if there are network problems. Pressing SK2 during a redial attempt will abort it.

☛ 1 6 3 ➔ 1 to activate or 2 to deactivate the auto redial facility.

Basic Calls & Phone Use

Line ID (M164)

, The line ID (identification) facility is network dependent.

The line ID facility enables you to choose whether or not to send your own phone number when you make a call and also whether or not to display a caller’s phone number when you receive a call.

☛ 1 6 4 to display the Line ID screen with a ✔ over an activated line and a ✘ over a deactivated line. ☛ To set the status of each line (see the table on the right), highlight a line (the line will flash when selected). ☛ SK1 to set the line identification on or off ➔ to save the current settings.

Line type Setting

Outgoing Send own #

Show connected #

Incoming Show Incoming #

Return own #

International dialling codes

When you make an international call from any country, you must start by dialling a special international access code. Your phone has the facility to prefix a + symbol to the numbers, so that you need not enter the access code for the country that you are calling from.

Entering international dialling codes

☛

Hold down 0. The 0 character displayed will change to a + character ➔ Key in the country code, area code, and phone number that you wish to call. The UK country code is always 44, no matter what country you are dialling from. For example, a typical UK number of 0131 1234567 is entered as:

International access country code area code phone number

+ 44 131 1234567

Roaming

, You will be charged for calls forwarded to you while roaming.

The roaming facility enables you to use your phone in many parts of the world and pay all charges through your normal service provider. Your network operator usually has agreements with named networks in other countries so that automatic roaming can take place with these named networks. The phone also allows you to set network preferences of your own.

When dialling, you will need to add the international access codes if required. So, storing all numbers with the codes (such as +44 for UK) is helpful (see “Entering international dialling codes”).

2 Before leaving your home country, you should select any preferences such as bar calls or call diversion.

Setting Automatic or Manual network selection (M181)

☛

1 8 1 ➔ 1 to select the automatic mode or 2 to select the manual mode.

, Before you manually select a network, ensure it is covered under the agreement you have with your service provider.

New search (M182)

☛

1 8 2 to search the available networks➔ Highlight the desired network ➔ to connect to it.

Basic Calls & Phone Use

Viewing/editing network list (M183)

, Before editing your network list, please consult with your service provider.

☛ 1 8 3 to read the network list in the SIM memory ➔ Highlight the required network ➔

No. SIM list Options menu

1Add Adds a new network to the list.

2Move Moves the highlighted network within the list.

☛ Use ▲ and ▼ to move the network ➔ SK1

3Remove Deletes the highlighted network.

2 Depending on the conditions, some options may be displayed in gray and not be available.

Selecting the frequency band (M184)

You have to select the frequency band to suit the location.

☛ 1 8 4 ➔ Select the required frequency band.

2 Frequency bands must be adjusted to suit the location when roaming (Europe, US, etc.), for the phone to work properly.

Text Entry

This section describes how you enter text.

Mode change

☛ With a text entry screen displayed, SK1 to change the text entry mode: T9

T9® English text input

Your phone incorporates T9® Text Input, enabling fast, easy and intuitive text input. For each letter to be keyed in, you only need to press the alphanumeric key once. The screen will display the word you may require based on the internal English dictionary of your phone.

☛ With a text entry screen displayed, SK1 until the entry mode is T9

i) For example, to enter “Good”:

☛ 4 6 6 3, and then 0 to confirm the word.

ii) To enter “Peter is good”:

☛ to shift to upper case (for one letter). You will see a green arrow in the Help area. ☛ 7 3 8 3 7 to display “Peter”, and then 0 to confirm. ☛ 4 7 to display “is”, and then 0 to confirm.

English text, Normal text (ABC), Numeric input

English input.

Text Entry

☛ 4 6 6 3 to display “good”, and then 0 to confirm and the sentence is completed.

▼▼▼

Key Function

0 Confirms a word and inserts a space.

1 Inserts a period or a single quote as in “Let’s”, “we’re”, “it’s”, etc.

SK1(List) Displays the list of other matching words.

SK1(Spell?) Activates the spell mode which temporarily deactivates T9

SK2(Dismiss) Cancels the T9

SK2(Next) or # Displays the next candidate.

▼

or Places the cursor.

0 to 9 (press and hold) Inserts the number.

CLR Deletes any character.

(press and hold) Press and hold to activate the highlight mode (see “Highlight mode” on page 33 for details).

# Activates symbol mode when no word is highlighted.

spell mode ends when you key in 0 to enter a space, or SK1(T9).

Toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case).

matching word list.

for you to spell the word in Normal text input. The

Normal text input

☛ With a text entry screen displayed, SK1 until the entry mode is Normal text (ABC) input. ☛ Use alphanumeric keys to enter letters. For example, to enter “e,” press 3 twice; to enter “f,” press 3 three times. For other functions, see the table

below.

2 When you are in the Normal text (ABC) input, any word entered that is not in the T9

Key Function

Toggles between lower case, shift (upper case for one letter) and caps lock (permanent upper case).

(press and hold) Press and hold to activate the highlight mode (see “Highlight mode” on page 33 for details).

0 Inserts a space.

0 to 9 (press and hold) Inserts the number.

CLR Deletes any character.

or Places the cursor.

# Activates symbol mode.

dictionary will be added automatically.

Text Entry

+ 69 hidden pages