TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
Caution:
When operating the MultiSync LCD1860NX with a 220-240V AC power source in Europe, use the power cord provided with
the monitor.
In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment.
If a power cord is not supplied with this equipment please contact your supplier.
When operating the MultiSync LCD1860NX with a 220-240V AC power source in Australia, use the power cord provided with
the monitor.
For all other cases, use a power cord that matches the AC voltage of the power outlet and has been approved by and
complies with the safety standard of your particular country.
English
Declaration
We hereby certify that the colour monitor
MultiSync LCD1860NX (L182R4)
is in compliance with
Council Directive 73/23/EEC:
– EN 60950
Council Directive 89/336/EEC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
Declaration of the Manufacturer
and marked with
NEC-Mitsubishi Electric Visual
Systems Corporation
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
English-1
Canadian Department of Communications Compliance
Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 950.
FCC Information
1.Use the attached specified cables with the MultiSync LCD1860NX (L182R4) colour monitor so as not to interfere with
radio and television reception.
(1)Please use the supplied power cord or equivalent to ensure FCC compliance.
(2)Please use the specified shielded video signal cable, 15-pin mini D-SUB to 15-pin mini D-SUB cable,
DVI-D to DVI-D cable.
2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party:NEC-Mitsubishi Electronics Display of America, Inc.
Address:1250 North Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
Tel. No.:(630) 467-3000
Type of Product:Display Monitor
Equipment Classification:Class B Peripheral
Model:MultiSync LCD1860NX (L182R4)
We hereby declare that the equipment specified above conforms
to the technical standards as specified in the FCC Rules.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ENERGY STA R
is a U.S. registered trademark. All other brands and product names are trademarks or registered trademarks of their
respective owners.
As an ENERGY STAR® Partner, NEC-Mitsubishi Electronics Display of America has determined that this product meets the
ENERGY STAR guidelenes for energy efficiency. The ENERGY STAR emblem does not represent EPA endorsement of any product
or service.
English-2
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
•MultiSync LCD1860NX monitor with height adjustable base
•Power Cord(s)
•Video Signal Cable
•User’s Manual
•Cable Management Cover
•NEC LCD Setup Software, User’s Manual and other helpful files.
To see the User‘s Manual, Acrobat Reader 4.0 must be installed on your PC.
Power Cord(s)
English
MultiSync LCD1860NX
User’s ManualVideo Signal CableSoftware CD
Remember to save your original box and packing material to transport or ship the monitor.
*
Cable Management Cover
English-3
Quick Start
To attach the MultiSync LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your
system (Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB to 15-pin mini D-SUB signal cable to the connector of
the display card in your system (Figure A.1).
For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal
cable to the MultiSync Macintosh cable adapter (Figure B.1).
Macintosh
Cable Adapter
(not included)
Figure A.1Figure B.1
NOTE:Some Macintosh systems do not require a Macintosh cable adapter.
3. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector on the back of the monitor.
Place the video signal cable (Figure C.1). Connect only DVI to input 2.
For the PC with Analog output: Connect the 15-pin mini D-SUB to the connector on the back of the monitor. Place the
video signal cable (Figure C.1). Connect only 15-pin mini D-SUB to input 1.
NOTE:Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module
and/or shorten the module’s life.
Collect cables and keep them at backside of the stand (Figure C.1). And cover the cables by the optional Cable
management Cover (Figure C.2).
Please check Tilt, Rise and Lower monitor screen when you manage cables.
4. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet
(Figure C.1).
NOTE:Use the supplied AC power cord. If it does not match the shape and the voltage of AC power outlet being used,
please refer to the Recommended Use section for proper use of the AC power cord.
5. The Vacation Switch on the left side of the monitor must be turned on. Turn on the monitor with the front power button
(Figure D.1) and the computer.
NOTE:There are two switches - one on the left side and on the front side of the monitor. DO NOT switch on/off quickly.
6. To complete the setup of your MultiSync LCD monitor, use the following OSM controls:
• Auto Adjust Contrast (Analog input only)
• Auto Adjust (Analog input only)
Refer to the Controls section of this User’s Manual for a full description of these OSM controls.
NOTE:If you have any problems, please refer to the Troubleshooting section of this User’s Manual.
NOTE:Refer to User’s Manual in the NEC LCD Setup Software CD case for installation and operation of this software.
English-4
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.