NEC HT1000 User Manual
HT1000
Entertainment Projector
User’s Manual
LIMITED WARRANTY
Except as specified below, the warranty that may be provided by the
dealer covers all defects in material or workmanship in this product.
The following are not covered by the warranty:
1. Any product on which the serial number has been defaced, modified
or removed.
2. Damage, deterioration or malfunction resulting from;
a. Accident, misuse, abuse, neglect, fire, water, dust, smoke, lightning or
other acts of nature, unauthorized product modification, or failure to fol-
low instructions supplied with the product.
b. Repair or attempted repair by non-authorized persons.
c. Any shipment of product (claim must be presented to the carrier).
d. Removal or installation of the product.
e. Any other causes which do not relate to a product defect.
3. Cartons, carrying cases, batteries, external cabinets, CDROM, or
anyaccessories used in connection with the product.
4. Removal or installation charges.
5. Cost of initial technical adjustments (set-up), including adjustment
of user controls. These costs are the responsibility of the dealer from
whom the product was purchased.
6. Payment of shipping charges.
GARANZIA LIMITATA
A parte la specificazione seguente, la graanzia che potrebbe essere
fornita dal rivenditore copre tutti i difetti di materiali o nella lavorazione
in questo prodotto. I seguenti non sono coper ti dalla garanzia :
1. Ogni prodotto che ha il numero seriale difettoso, modificato o rimosso.
2. Danni, deterioramento o malfunzionamento risultanti da;
a. Incidenti, abuso, cattivo uso, negligenza, fuoco, acqua, polvere, fumo,
fulmini o altri atti naturali di tipo naturale, modifiche inautorizzate del
prodotto, o errori nel seguire le istruzioni fornite con il prodotto.
b. Riparazioni o tentativi di riparazioni effettuati da persono non autorizzate.
c. Qualsiasi trasporto del prodotto (i reclami devono essere presentati dal
corriere).
d. Rimozione o installazione del prodotto.
e. ogni altra causa non relativa ad un deficit del prodotto.
3. Cartoni, scatole di trasporto, batterie, armadietti esterni, CDROM, o
qualsiasi altro accessorio annesso al prodotto.
4. Carichi di rimozione o installazione.
5. Costi di aggiustamenti tecnici iniziali (set-up), includendo i comandi
di regolazione. Il rivenditore dal quale avete acquistato il prodotto è
responsabile di ciò.
6. Pagamento delle spese di consegna.
GARANTIE LIMITEE
Mis à part les point indiqués ci-dessous, la garantie pouvant être
couverte par le revendeur comporte l’ensemble des défauts se
rapportant au matériel ou aux travaux d’assemblage sur ce produit.
Les points suivants ne sont pas couverts par la garantie:
1. Les produits dont les numéro de série a été effacé, modifié ou retiré.
2. Dommages, dégâts ou dysfonctionnement suite à;
a. Un accident, mauvaise utilisation, abus, négligences, incendies, dégats
dûs aux eaux, à la poussière, à la fumée, aux éclairs ou autres phénomènes
naturels, à une modification non autorisée du produit, ou à la non-
conformité aux instructions fournies avec le produit.
b. Réparation ou tentative de réparation par des personnes non autorisées.
c. Toute expédition du produit (les plaintes doivent être adressées à la société
de frêt).
d. Démontage ou installation du produit.
e. Toute autre cause ne se rapportant pas à un défaut du produit.
3. Les car tons, boîtes, piles, caissons externes, CDROM, ou tout autre accessoire utilisé avec ce poduit.
4. Prix de démontage ou d’installation.
5. Coût des réglages techniques de base (mise au point), incluant les
réglages des commandes utilisateurs. Ces coûts sont placés sous
la responsabilité du revendeur auprès duquel le produit a été acheté.
6. Paiement des frais de transport.
BESCHRÄNKTE GARANTIE
Außer in den unten beschriebenen Fällen deckt die vom Händler unter
Umständen gewährte Garantie alle Material- oder Herstellungsfehler
dieses Produktes ab. In den folgenden Fällen wird keine Garantie
gewährt:
1. Wenn die Seriennummer des Produktes unleserlich gemacht,
geändert oder entfernt worden ist.
2. Bei einer Beschädigung, Beeinträchtigung oder Funktionsstörung,
die aus folgenden Fällen resultiert:
a. Unfall, falscher Gebrauch, Missbrauch, Fahrlässigkeit, Feuer, Wasser,
Staub, Rauch, Blitzeinschlag oder andere Naturereignisse, nicht
autorisierte Veränderungen des Produktes oder die Missachtung der dem
Produkt beigefügten Anleitung.
b. Reparatur oder der Versuch einer Reparatur durch nicht autorisierte
Personen.
c. Jeglicher Transport des Produktes (die Haftung liegt in diesem Fall bei
der den Transport durchführenden Person).
d. Entfernung oder Installation des Produktes.
e. Jegliche andere Ursachen, die nicht mit einem Defekt dieses Produktes
zusammenhängen.
3.
Verwendung von Kartons, Transportkisten, Batterien, Außengehäusen,
CD-ROMs oder anderem Zubehör zusammen mit diesem Produkt.
4. Entfernungs- oder Installationsforderungen und –kosten.
5. Kosten der technischen Anfangseinstellungen (Setup), einschließlich
der Einstellungen der Benutzersteuerungen. Diese Kosten sind vom
Händler zu tragen, von dem das Produkt erworben wurde.
6. Bezahlung von Transportkosten.
GARANTÍA LIMITADA
A excepción de lo que se especifica abajo, la garantía que puede ser
suministrada por el distribuidor cubre todos los defectos en material o
elaboración en este producto. Lo siguiente no es cubier to por la garantía:
1. Cualquier producto en el cual el número serial haya sido desfigurado,
modificado o removido.
2. Daños, deterioro o malfuncionamiento resultado de;
a. Accidente, mal manejo, abuso, negligencia, fuego, agua, polvo, humo,
relámpagos u otros fenómenos naturales, modificaciones del producto
sin autorización, fallas en el seguimiento de las instrucciones
suministradas con el producto.
b. Reparación o intentos de reparación por personas no autorizadas.
c. Cualquier envío del producto (el reclamo debe presentarse al
transportador).
d. Remoción o instalación del producto.
e. Cualquier otra causa que no este relacionada con un defecto del producto.
3. Cartones, estuches de transporte, pilas, gabinetes externos,
CDROM, o cualquier accesorio utilizado en conexión con el producto.
4. Costos por instalación o remoción.
5. Costo de los ajustes técnicos iniciales (configuración), incluyendo
el ajuste de los controles de usuario. Estos costos son
responsabilidad del distribuidor donde se adquirió el producto.
6. Pago de los costos de envío.
BEGRÄNSAD GARANTI
Garantin som ges av återförsäljaren täcker alla brister i material och
utförande med undantag av vad som anges nedan. Följande täcks inte
av garantin:
1. Produkter vars serienummer har blivit oläsligt, modifierats eller tagits
bort.
2. Skador, försämring eller felfunktion som beror på:
a. Olyckor, fel bruk, missbruk, vanskötsel, brand, vatten, rök, stoft, åska
eller annan orsak som beror på naturen, icke auktoriserad modifikation
av produkten samt underlåtenhet att följa anvisningarna som lämnas med
produkten.
b. Reparationer eller försök på reparation av icke auktoriserade personer.
c. Transportskador (dessa bör riktas till transportföretaget).
d. Avmontering eller installation av produkten.
e. Övriga orsaker som inte har något samband med produktens fel.
3. Förpackningslådor, bärväskor, batterier, externa höljen, CD-ROMskivor samt andra tillbehör som används tillsammans med produkten.
4. Avmonterings- och installationskostnader.
5. Kostnader för tekniska justeringar (inställning), inklusive justering
av användarreglagen. Dessa kostnader är återförsäljarens ansvar
där produkten köpts.
6. Betalning för transportkostnader.
LIMITED WARRANTY (USA and Canada only)
NEC SOLUTIONS’ PROJECTOR PRODUCTS
NEC Solutions (America), Inc. (hereafter NEC Solutions) warrants
this product to be free from defects in material and workmanship
under the following terms.
HOW LONG IS THE WARRANTY
NEC Solutions’ HT1000 projector is covered by a two (2) year
limited parts and labor warranty from the date of the first customer purchase. The lamp when used under normal operating
conditions is warranted for 1000 hours or six months, whichever
comes first.
WHO IS PROTECTED
This warranty may be enforced only by the first purchaser, and is
not transferable.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in
material or workmanship in this product.
NEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS
LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT NEC SOLUTIONS’ OPTION. REPLACEMENT PRODUCTS MAY
BE NEW OR ‘LIKE NEW’. The following are not covered by the
limited warranty and NEC Solutions shall not be liable for:
1. Any product which is not distributed in the U.S.A. or Canada
by NEC Solutions or which is not purchased, installed, and
operated in the U.S.A or Canada.
2. Any product on which the serial number has been defaced,
modified or removed.
3. Normal decrease in lamp light output over time.
4. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, abuse, neglect, improper ventilation, fire,
dust, smoke, water, lightning or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone other than a NEC
Solutions authorized service center.
c. Any shipment of the product (claims must be presented to
the carrier).
d. Removal or installation of the product.
e. Any other cause which does not relate to a product defect.
f. Use of the product beyond normal operating conditions.
Normal operating conditions are defined as product use
not in excess of 8 hours per day and 260 days per year.
5. Cartons, carr ying cases, shipping cases, batteries, external
cabinets, magnetic tapes, or any accessories used in connection with the product.
6. Service required as a result of third party components.
WHAT NEC SOLUTIONS WILL PAY FOR
NEC Solutions will pay labor and material expenses for covered
items, but NEC Solutions will not pay for the following:
1. Removal or installation charges.
2. Costs of technical adjustments, set-up, maintenance, or adjustment of user controls.
3. Payment of shipping and related charges incurred in returning
the product for warranty repair.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom
you purchased the product.
Whenever warranty service is required, the original dated invoice
2.
(or a copy) must be presented as proof of warranty coverage. In
order to obtain warranty service, you may be required to describe
and demonstrate the problem to your dealer or to NEC Solutions.
3. All products returned to NEC Solutions for service MUST have
prior approval. To receive approval or for the name of the
nearest NEC Solutions authorized service center, call NEC
Solutions at 800-836-0655.
4. It shall be your obligation and expense to ship the product,
freight prepaid, or to deliver it to a NEC Solutions authorized
service center, in either the original package or a similar package affording an equal degree of protection.
In the event a product is returned to NEC Solutions for warranty
5.
service, and it is determined that there is no product defect or that
the product condition is not covered by this limited warranty, a
diagnostic service fee may be charged to the customer.
LIMITATION OF IMPLIED WARRANTIES
EXCEPT AS EXPRESSLY SET FOR TH IN THIS LIMITED W ARRANTY,
NEC SOLUTIONS MAKES NO OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A P ARTICULAR PURPOSE. ANY IMPLIED W ARRANTIES THA T MA Y BE IMPOSED BY LA W ARE LIMITED TO THE TERMS
AND DURATION OF THIS LIMITED WARRANTY.
EXCLUSION OF DAMAGES
NEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS
LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT NEC SOLUTIONS’ OPTION. NEC SOLUTIONS SHALL NOT
BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS
IN THIS PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME,
COMMERCIAL LOSS; OR
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
HOW STATE LAW RELATES TO THE WARRANTY
SOME STATES DO NOT ALLOW LIMITA TIONS ON HOW LONG
AN IMPLIED W ARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OR LIMITA TION OF INCIDENT AL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
FOR MORE INFORMATION, CONTACT:
NEC SOLUTIONS (AMERICA), INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
TELEPHONE 800-836-0655
www.necvisualsystems.com
Customers are cautioned that product performance is affected by
system configuration, software, the application, customer data,
and operator control, among other factors. While NEC Solutions’
products are considered to be compatible with many systems, the
specific functional implementation by the customers of the product may vary. Therefore, the suitability of a product for a specific
purpose or application must be determined by the customer and
is not warranted by NEC Solutions.
Printed in Japan
7N8P1722
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
U.S. Responsible Party:
Address:
Tel. No.:
Type of Product:
Equipment Classification:
Models:
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
NEC Solutions (America), Inc.
1250 N. Arlington Heights Road
Itasca, Illinois 60143
(630) 467-5000
Projector
Class B Peripheral
HT1000
HT1000
Entertainment Projector
User’s Manual
English
Deutsch
Français
Italiano
Español
Svenska
IMPORTANT INFORMATION
Safety Cautions
Precautions
Please read this manual carefully before using your NEC HT1000 Projector and keep the manual handy for future reference. Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power
outlet.
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the
unit may be sufficient to cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any part inside of
the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this unit has been
provided.
The information should be read carefully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance -3. GSGV:
The sound pressure level is less than 70 dB (A) according to ISO 3744
or ISO 7779.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by NEC Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could void your right to
operate this equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for
help.
In UK, a BS approved power cable with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cable is not
supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
E-2
Fire and Shock Precautions
1.
Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at
least 3 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver
into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified
NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the
projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out
of the lens, can cause unpredictable outcome such as fire or injury
to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while
the projector is on. Doing so can lead to melting of the cap and
possibly burning your hands due to the heat emitted from the light
output.
7. The projector is designed to operate on a power supply of 100-120
or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this
requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can
cause elecrical shock or fire.
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to
ship your HT1000 Projector.
R
E
W
PO
S
ATU
Y
B
ST
D
N
A
T
S
N
LAMP
O
M
R
O
F
E
R
D
3
T
S
U
J
D
A
O
T
C
N
E
A
U
L
C
A
E
D
C
R
R
A
U
C
-
O
C
S
P
R
E
T
N
E
T
C
E
L
E
S
U
N
E
M
Projector
Lens cap
(24FT8661)
E
F
F
E
C
T
O
PO
SITIO
N
MAG
NIFY
H
EL
P
V
PIC-MUT
O
LU
M
E
E
F
OLD
ER
SLIDE
L
I
S
T
Remote control
OFF
V
IDEO
AU
S-VIDEO
TO
PO
ADJ
WE
.
R
C
OMPONENT
O
N
RGB
DV
S
I
E
L
E
C
T
A
S
P
E
CT
FREE
ZE
3
R
D
PICTU
R
E
F
O
RE
R
M
VIEW
ER
S
L
ID
E
Batteries
(7N900371)
Power cable
(7N080204: North America)
(7N080003: G model)
Soft carrying case
(24BS7111)
String and rivet
(24C05051) (24C04531)
RGB signal cable
(7N520001)
CAUTION
1. Do not try to touch the ventilation outlet on the front and side as it
can become heated while the projector is turned on.
2. Do no use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
3. Enable High-Speed Fan mode if you continue to use the projector
for consecutive days. (From the Advanced menu, select [Projector
Options] → [Setup] → [Page 4] → [High Speed Fan Mode].)
4. Do not unplug the power cable from the wall outlet under any one of
the following circumstances.
Doing so can cause damage to the projector:
* While the Hour Glass icon appears.
* While the message "Please wait a moment." appears. This mes-
sage will be displayed after the projector is turned off.
* While the cooling fans are running. (The cooling fans continue to
work for 90 seconds after the projector is turned off).
5. Do not eject the PC card while its data is being accessed. Doing so
can damage your PC card data.
6. Do not hold the lens part with your fingers. Doing so could pinch
fingers or hands causing injury.
Lamp Replacement
•To replace the lamp, follow all instructions provided on page E-48.
• Be sure to replace the lamp when the message "The lamp has
reached the end of its usable life. Please replace the lamp."
appears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
• Allow a minimum of 90 seconds to elapse after turning off the projector. Then turn off the main power switch, disconnect the power
cable and allow 60 minutes to cool the projector before replacing
the lamp.
For Europe only
E-3
Audio cable
(7N520014)
S-Video cable
(7N520015)
SCART adapter
(7N520018)
Composite video cable
(7N520016)
Component video cable
(RCA⳯3-to-RCA⳯3)
(7N520017)
Quick
Connect
User’s
manual
Guide
For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
TABLE OF CONTENTS
IMPORTANT INFORMATION ........................................... E-2
Safety Cautions ........................................................................................... E-2
What's in the Box? ...................................................................................... E-3
INTRODUCTION ......................................................... E-5
Introduction to the Projector ....................................................................... E-5
Part Names of the Projector ........................................................................ E-6
Attaching the lens cap .............................................................................. E-6
Top Features............................................................................................. E-7
Ter minal Panel Features ........................................................................... E-8
Part Names of the Remote Control ...........................................................E-9
Battery Installation .............................................................................. E-10
Remote Control Precautions ............................................................... E-10
Operating Range ................................................................................. E-10
INSTALLATION AND CONNECTIONS .................................. E-11
Setting Up the Screen and the Projector ................................................... E-11
Selecting a Location ............................................................................... E-11
Throw Distance and Screen Size ............................................................ E-12
Making Connections .................................................................................. E-13
Wiring Diagram ...................................................................................... E-13
Connecting Your VCR or Laser Disc Player ............................................ E-14
Connecting Your DVD Player .................................................................. E-15
Connecting Your PC or Macintosh Computer .........................................E-16
When Viewing a DVI Digital Signal ......................................................... E-17
Connecting the Supplied Power Cable ....................................................E-17
PROJECTING AN IMAGE (BASIC OPERATION) ......................E-18
Turning on the Projector ............................................................................ E-18
Selecting a Source .....................................................................................E-19
Adjusting the Picture Size and Position ..................................................... E-19
Correcting the Horizontal and Vertical Keystone Distortion (3D Reform) .. E-20
Optimizing RGB Picture Automatically ...................................................... E-21
Turning Up or Down Volume ..................................................................... E-22
Turning off the Projector ........................................................................... E-22
CONVENIENT FEATURES .............................................. E-23
Using Sweet Vision function ......................................................................E-23
Using Zoom Position ................................................................................. E-23
Turning Off the Image and Sound .............................................................. E-24
Freezing a Picture ...................................................................................... E-24
Enlarging and Moving a Picture .................................................................E-24
Getting the On-line Help ............................................................................ E-24
Changing Background Logo ...................................................................... E-25
USING THE VIEWER ................................................... E-26
Making the Most out of the Viewer Function ............................................. E-26
Operating the Viewer Function from the Projector (playback) ................... E-27
Projecting slides (Viewer) ...................................................................... E-27
Auto Play Mode ...................................................................................... E-28
Switching to Slides Directly from Other Input Modes ............................ E-28
Viewing Digital Images ........................................................................... E-28
Storing Images Displayed on the Projector on the PC card (Capture) .... E-28
Deleting Captured Images ...................................................................... E-29
Using the PC Card Files Fucntion (PC Card Files) ................................... E-29
USING ON-SCREEN MENU ............................................ E-30
Basic Menu Operation ............................................................................... E-30
Using the Menus .................................................................................... E-30
Customizing the Menu ........................................................................... E-30
Menu tree .................................................................................................. E-31
Menu Elements ..........................................................................................E-34
Entering Alphanumeric Characters by Using the Menu .......................... E-35
Menu Descriptions & Functions ................................................................ E-35
Source Select ......................................................................................... E-35
Video/S-Video/Component/RGB/DVI (DIGITAL)/Viewer/Entry List
Image Options ........................................................................................ E-36
Selecting Aspect Ratio ........................................................................ E-36
Masking Unwanted Area (Blanking) .................................................... E-38
Adjusting Position and Clock .............................................................. E-38
Zoom Position .................................................................................... E-38
Selecting Resolution ........................................................................... E-38
Selecting Overscan Percentage ........................................................... E-38
Selecting Video Filter Level ................................................................. E-38
Selecting Noise Reduction Level ......................................................... E-38
Selecting Signal Type .......................................................................... E-38
Picture Management .............................................................................. E-38
Picture ................................................................................................ E-39
User Adjust (when using User 1 to 4) ................................................. E-39
Selecting Reference Setting ..........................................................E-39
Selecting Gamma Correction Mode .............................................. E-39
Selecting Color Correction ............................................................E-39
Adjusting Color Temperature and White Balance .......................... E-39
Picture Options .............................................................................E-39
Sweet Vision/3D Y/C Separation/Deinterlace/Black Expansion/Contrast Enhancement
Projector Options ................................................................................... E-40
Using 3D Reform ................................................................................ E-40
Keystone ....................................................................................... E-40
Cornerstone ..................................................................................E-40
Menu [Page1] ..................................................................................... E-40
Selecting Menu Language/Selecting Menu Mode/Customizing the
Menu/Selecting Menu Display Time
Menu [Page 2] .................................................................................... E-40
Tur ning On / Off Source Display / Turning On / Off Message / Selecting
Menu Color
Setup [Page 1] .................................................................................... E-41
Setting Lamp Mode to Normal or Eco/Selecting Projector Orientation/
Selecting a Color or Logo for Background
Setup [Page 2] .................................................................................... E-41
Setting Viewer Options/Selecting Capture Options
Setup [Page 3] .................................................................................... E-41
Selecting Signal Format
Setup [Page 4] .................................................................................... E-41
Enabling Auto Adjust/Enabling Auto Start/Enabling Power Management/Enabling Power Off Confirmation/Enabling Horizontal and Vertical Keystone Correction Save/Enabling High Speed Fan Mode/Enabling
Idle Mode/Enabling Screen Trigger/Enabling 3D Surround/Clearing
Lamp Hour Meter
Setup [Page 5] .................................................................................... E-42
Selecting Communication Speed/Selecting Default Source/Disabling the
Cabinet Buttons
Selecting Aspect Ratio and Position for Screen .................................. E-43
Setting LAN Mode ............................................................................... E-43
IP Address .................................................................................... E-43
Mail .............................................................................................. E-44
Status ........................................................................................... E-44
Setting a Password ............................................................................. E-45
Security ............................................................................................... E-45
Tools ...................................................................................................... E-47
Using Sleep Timer ............................................................................... E-47
Using Capture ..................................................................................... E-47
Using PC Card Files ............................................................................ E-47
Help ........................................................................................................E-47
Contents ............................................................................................. E-47
Information ......................................................................................... E-47
Returning to Factory Default .................................................................. E-47
MAINTENANCE ........................................................E-48
Replacing the Lamp ...................................................................................E-48
Cleaning .................................................................................................... E-49
Lens Protector ....................................................................................... E-49
TROUBLESHOOTING ................................................... E-50
Power Indicator ......................................................................................... E-50
Status Indicator ......................................................................................... E-50
Lamp Indicator .......................................................................................... E-50
Common Problems & Solutions ................................................................ E-51
When using the Viewer function ................................................................ E-51
SPECIFICATIONS ...................................................... E-52
APPENDIX ..............................................................E-53
Cabinet Dimensions .................................................................................. E-53
Pin Assignments of D-Sub RGB Input Connector ...................................... E-53
Compatible Input Signal List ..................................................................... E-54
Compatible Input Signal List for DVI Signal (RGB only) ............................ E-55
PC Control Codes and Cable Connection ................................................... E-56
PC Control Connector (DIN-8P) ................................................................ E-56
Using Software Keyboard .......................................................................... E-56
Operation Using an HTTP Browser ............................................................ E-57
TravelCare Guide ....................................................................................... E-58
E-4
INTRODUCTION
Introduction to the Projector
This section introduces you to your new HT1000 Projector and describes
the features and controls.
Congratulations on Your Purchase of The HT1000 Projector
The HT1000 is our most sophisticated single chip DLP™ based projector for the commercial and residential entertainment user. With the
HT1000 you will enjoy projecting images up to 200" (measured diagonally) from your DVD player, VCR, satellite hookup, HDTV source, PC
or Macintosh computer (desktop or notebook) and images from you
digital camera. The HT1000 can be setup on a coffee table, tabletop,
cart, bookshelf or permanently installed*
quick connect guide and full function remote, you will be ready to immerse yourself in big screen enjoyment.
Features you’ll enjoy on the HT1000:
• Phenomenal 3000:1 contrast ratio with a variable IRIS that allows
you to fine-tune the image contrast
• 3D Reform technology for positioning the projector in off center locations in the room and still get aligned images
• NEC designed and developed SweetVision™ technology for enhanced images, more vibrant colors and blacks richer with detail
®
•Faroudja
• Ability to display 16:9 and 4:3 aspect ratio sources
• HDTV, SDTV compatibility
• 3D 10-bit video decoder for expanded black levels and adaptive
gamma correction
• Digital photo viewer to display larger than life images from your digital cameras PC or compact flash card
• Built in speakers with 3D sound for an integrated audio solution
• Easy set up and operation
• High performance long life lamp for low total operating costs
• Eco-mode lamp technology for increased lamp life and energy savings
• Uncompromising display of video and data. Improves white level, color
accuracy, dynamic range, and display of varying levels of black in an
image.
• Sealed optics for reduced maintenance and better performance in
dusty areas
• Wireless remote control operation
• Network capable with a wired card for the ability to maintain and
control your projector from your computer
• Smart security settings for password protection, control panel lock
and PC card protection key to help prevent unauthorized use
• Multiple video mode selections depending on your source.
•Control the unit with a PC using the PC Control port.
• NEC’s exclusive Advanced AccuBlend intelligent pixel blending technology - an extremely accurate image compression technology - offers a crisp image with HTDV 1080p (1920⳯1080) resolution*
• Supports most IBM VGA, SVGA, XGA, SXGA (with Advanced
AccuBlend)*
other RGB signals within a horizontal frequency range of 24 to 69 kHz
and a vertical frequency range of 48 to 88 Hz. This includes NTSC,
PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 standard video
signals.
DCDi™ video processing technology
2
, Macintosh, component signal (YCbCr/ YPbPr) or any
1
. With an extensive input panel,
2
.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
•You can control the projector with a PC using the PC Control port
and wired LAN.
• The contemporary cabinet design is light, compact, easy to carry.
1
Do not attempt to mount the projector on a ceiling yourself.
*
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
2
*
HDTV 1080p (1920⳯1080), HDTV 1080i (1920⳯1080) and
HDTV 720p (1280⳯720) are displayed with NEC’s Advanced
AccuBlend.
Digital Light Processing, DLP, Digital Micromirror Device and DMD are
trademarks of Texas Instruments.
The specifications are subject to change without notice.
Faroudja is a registered trademark of Faroudja Laboratories, Inc. DCDi
is a trademark of Faroudja Laboratories, Inc.
All other trademarks are the property of their respective owners.
All specifications subject to change without notice.
E-5
Part Names of the Projector
PC CONTROL
RGB IN
DVI-D IN
SG TRIGGER
VIDEO IN
S-VIDEO IN
S
-V
ID
E
O
S
-V
ID
E
O
R
G
B
/D
V
I
R
G
B
/D
V
I
V
ID
E
O
V
ID
E
O
A
U
D
IO
IN
A
U
D
IO
IN
C
O
M
P
O
N
E
N
T
Y
C
b
/P
b
C
r/P
r
Remote Sensor (See page E-10)
Focus Ring (See page E-20)
Controls (See page E-7)
WER
PO
S
TU
A
Y
B
ST
D
N
A
P
T
S
N
LAM
O
M
R
O
F
E
R
D
3
T
S
U
J
D
A
O
T
C
N
E
A
U
L
C
A
E
D
C
R
R
A
U
C
-
O
C
S
P
R
E
T
N
E
T
C
E
L
E
S
U
N
E
M
Ventilation (inlet)
Ventilation (outlet)
Heated air is exhausted from here
Built-in Security Slot ( )*
Zoom Lever (See page E-20)
Adjustable Tilt Foot Lever (See page E-19)
Carrying Handle
Lens
Adjustable Tilt Foot (See page E-19)
Lens Cap
Iris Lever (See page E-20)
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
PC Card Eject Button
PC Card Slot
Stereo Speaker (2W)
Lamp cover (See page E-48)
Ventilation (outlet)
Heated air is exhausted from here
Remote Sensor (See page E-10)
Lamp cover screw
Rear Foot
Rear Foot
Rotate to make the projector level. (See page E-20)
AC Input
Connect the supplied power cable's three-pin plug here, and plug the
other end into an active wall outlet. (See page E-17)
Main Power Switch
When you plug the supplied power cable into an active wall outlet and
turn on the Main Power switch, the POWER indicator turns orange and
the projector is in standby mode. (See page E-18)
Attaching the lens cap
To attach the lens cap to the bottom with the supplied string and rivet:
1. Thread the string through the
hole on the lens cap and then
tie a knot in the string.
2. Use the rivet to attach the
string to the bottom of the
projector.
E-6
Top Features
910 45 11
2
678 121 3
1. POWER Button (ON / STAND BY) ( )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
NOTE: To turn on or off the projector, press and hold this button for a minimum of two seconds.
2. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred,
the lamp cover is not attached properly or the projector has overheated. If this light remains orange, it indicates that you have pressed
a cabinet key while the Control Panel Key Lock is enabled. See the
Status Indicator section on page E-50 for more details.
3. POWER Indicator
When this indicator is green, the projector is on; when this indicator
is orange, it is in standby or idle mode. See the Power Indicator section on page E-50 for more details.
4. SOURCE Button
Use this button to select a video source such as a VCR, DVD player,
PC or Viewer (PC card).
Press and release this button quickly to display the Source List.
Each time this button is pressed for a minimum of ONE second the
input source will change as follows:
Video → S-Video → Component → RGB → DVI (DIGITAL) → Viewer →
Video → ...
If no input signal is present, the input will be skipped.
5. AUTO ADJUST Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture. Some signals may not be displayed correctly or take
time to switch between sources.
NOTE: This function may not be available depending upon the input signal.
6. PC CARD Access Indicator
Lights while accessing a PC card.
7. ENTER Button
Executes your menu selection and activates items selected from the
menu.
8. CANCEL Button
Press this button to exit "Menus". Press this button to return the adjustments to the last condition while you are in the adjustment or
setting menu.
9. SELECT 왖왔왗왘 (+) (–) / Volume Buttons
왖왔 : Use these buttons to select the menu of the item you wish to
adjust. When no menus appear, these buttons work as a volume control.
왗왘 : Use these buttons to change the level of a selected menu item.
A press of the 왘 button executes the selection. When the menus
or the Viewer tool bar is not displayed, these buttons can be
used to select a slide, or to move the cursor in Folder List or
Slide List.
10. MENU Button
Displays the menu.
11. LAMP Indicator
If this light blinks red rapidly, it's warning you that the projection lamp
has exceeded 1500 hours (up to 2000 hours in Eco mode) of service.
After this light appears, replace the lamp as soon as possible. (See
page E-48). If this is lit green continually, it indicates that the lamp
mode is set to Eco. See the Lamp Indicator section on page E-50 for
more details.
12. 3D REFORM Button
Press this button to enter 3D Reform mode to correct the keystone
(trapezoidal) distortion, and make the image square.
E-7
Terminal Panel Features
PC CONTROL
VIDEO IN S-VIDEO IN
93511
71213
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
SC TRIGGER
RGB IN
DVI-D IN
24110 86
1. RGB IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player. This connector also
supports SCART output signal. See page E-16 for more details.
2. DVI-D IN (DVI 24 Pin)
This connector can be used to accept digital signal output from a
computer or a setup box with a DVI connector. (HDCP compatible)
3. RGB/DVI AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your computer connected to RGB IN or DVI-D IN.
4. COMPONENT (Y, Cb/Pb, Cr/Pr) input Connectors (RCA)
Connect component video outputs (Y/Cb/Cr, Y/Pb/Pr) of the external
equipment such as DVD player.
NOTE: These connectors accept component signal only.
5. COMPONENT AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your DVD player or
component equipment connected to COMPONENT IN.
6. VIDEO IN (RCA)
Connect a VCR, DVD player or laser disc player here to project video.
7. VIDEO AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your VCR, DVD player
or laser disc player connected to VIDEO IN.
8. S-VIDEO IN (Mini DIN 4 Pin)
Connect a VCR, DVD player or laser disc player with S-Video output.
NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.
9. S-VIDEO AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your VCR, DVD player
or laser disc player connected to S-VIDEO IN.
10. PC CONTROL Port (Mini DIN 8 Pin)
Use this port to connect your PC to control your projector via a serial
cable. This enables you to use your PC and serial communication
protocol to control the projector. The NEC optional serial cable
(CA03D) is required to use this port. If you are writing your own program, typical PC control codes are on page E-56. A cap is put on the
port at the factory. Remove the cap when using the port.
11. SC TRIGGER Mini Jack
When the projector is powered ON the screen trigger output sends a
high voltage trigger to the screen controller and the screen will go
down.
When the projector is powered OFF the screen trigger stops sending
a low voltage trigger to the screen controller and the screen will go
up.
NOTE: To enable the SC.TRIGGER function, be sure to turn on "Screen Trigger" in "Page 4" of the Setup. See page E-42.
NOTE: Screen Controllers are supplied and supported by screen manufactures. This option is not included with the projector.
NOTE: Do not use this jack for anything other than intended use. Connecting
an audio cable or equivalent to the SC. TRIGGER Mini Jack causes damage to
this mini jack.
Stereo mini cable
(not supplied)
Tip (12V)
Ring (NC)
Sleave (ground. 0V)
12. PC CARD Eject Button
Press to eject a PC card partially.
13. PC CARD Slot
Insert a PC card or commercially available wired LAN card here.
E-8
R
E
ER
M
Part Names of the Remote Control
3D
E
A
O
T
U
A
POWER
E
M
SELECT
FREEZE
PICTURE
VOLUME
SELECT
COMPONENT
N
U
A
C
3D REFORM
VIEWER
SLIDE
FOLDER
SLIDE
EZ
ON
RGB
DVI
L
E
C
N
LIST
1. Infrared Transmitter
Direct the remote control toward
the remote sensor on the projector cabinet.
2. LED
VI
D
B
RG
.
J
D
N
COMPONENT
O
R
E
S-VIDEO
OW
P
EO
ID
V
FF
O
Flashes when any button is
pressed.
1
3. POWER ON Button
If the main power is applied, you
can use this button to turn your
projector on.
NOTE: To turn on the projector, press
and hold the POWER ON button for a
minimum of two seconds.
2
4
OFF
6
VIDEO
AUTO ADJ.
S-VIDEO
4. POWER OFF Button
You can use this button to turn
your projector off.
NOTE: To turn off the projector, press
and hold the POWER OFF button for
a minimum of two seconds.
5. VIDEO Button
Press this button to select an
NTSC, PAL, PAL-N, PAL-M,
PAL60, SECAM or NTSC4.43
compatible video source from a
VCR, DVD player, or laser disc
player.
6. S-VIDEO Button
Press this button to select an
11
19
15
18
20
21
22
23
24
E
N
T
E
R
ASPECT
EFFECTOR
POSITION MAGNIFY
HELP
PIC-MUTE
S-Video source from a VCR, DVD
player or laser disc player.
7. COMPONENT Button
Press this button to select a video source from component equipment connected to your COMPONENT input.
8. RGB Button
Press this button to select a video source from computer or component equipment connected to your RGB INPUT port.
9. AUTO ADJ Button
Use this button to adjust an RGB source for an optimal picture. Some
signals may not be displayed correctly or take time to be displayed.
See page E-21.
NOTE: This function may not be available depending upon the input signal.
10. DVI Button
Press this button to select a DVI digital signal from a computer or
settop box.
11. MENU Button
Displays the menu for various settings and adjustments.
12. SELECT 왖왔왗왘 Button
왖왔 : Use these buttons to select the menu of the item you wish to
adjust.
왗왘 : Use these buttons to change the level of a selected menu item.
A press of the 왘 button executes the selection. When the menus
or the Viewer tool bar is not displayed, these buttons can be
used to select a slide, or to move the cursor in Folder List or
Slide List.
T
E
M
OIN
U
P
L
VO
RE
P
F
L
E
H
T
C
E
P
AS
13. ENTER Button
Executes your menu selection and activates items selected from the
menu.
14. CANCEL Button
Press this button to exit "Menus". Press this button to return the adjustments to the last condition while you are in the adjustment or
setting menu.
15. ASPECT Button
Press this button to display the Aspect Ratio select screen. See page
E-36.
3
16. FREEZE Button
This button will freeze a picture. Press again to resume motion.
7
85
17. 3D REFORM Button
109
Press this button to enter 3D Reform to correct the keystone (trapezoidal) distortion, and make the image square. See page E-20.
12
18. EFFECTOR Button
Press this button to display the Sweet Vision setup screen. You can
1413
set options for the Sweet Vision feature in the Setup from the menu.
See page E-23.
19. PICTURE Button
16
Press this button to display the Picture Management window. See
17
page E-38.
25
20. POSITION Button
26
This button adjusts position of a zoomed image. See page E-23.
27
21. MAGNIFY (+) (–) Button
28
Use this button to adjust the image size up to 400%. The image is
magnified about the center of the screen. When the image is magnified, you can move the image by using the SELECT 왖왔왗 왘 button.
See page E-24.
22. HELP Button
Provides the online help or the set information.
23. PIC-MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an image
and sound without turning off the menu.
24. VOLUME (+) (–) Button
Press (+) to increase the volume and (–) to decrease it.
25. VIEWER Button
Press this button to select the Viewer source.
26. SLIDE (+) (–) Button
Press (+) to select the next folder or slide and (–) to select the previous folder or slide. See page E-27.
27. FOLDER LIST Button
Press this button to select Viewer source to display a list of folders
included in a PC card. See page E-27.
28. SLIDE LIST Button
Press this button to select Viewer source to display a list of slides
included in a PC card. See page E-27.
E-9
Battery Installation
1. Press firmly and slide the battery cover off.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the
batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of
batteries together
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries' polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not
mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT 왗왘왖왔 button while installing new
batteries, the remote control may fail to work properly.
Should this happen, remove the batteries and then install them again
without touching the SELECT button.
Operating Range
7m/22 feet
7m/22 feet
30°
25°
30°
30°
Remote sensor on the
projector cabinet
• The infrared signal operates by line-of-sight up to a distance of about
22 feet / 7 m and within a 55°(Front) / 60°(Rear) angle of the remote
sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor.
Weak batteries will also prevent the remote control from properly
operating the projector.
Remote control
E-10
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
Set up a screen and the projector.
z
x
Connect your video equipment to the projector. See page E-13 – 17.
c
Connect the supplied power cable. See page E-17.
NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. When
moving the projector or when it is not in use, cover the lens with the lens cap.
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the
image can be is approximately 30" (0.8 m) measured diagonally when the projector is roughly 4 feet
(1.0 m) from the wall or screen. The largest the image can be is 200" (5.08 m) when the projector is
about 23 feet (7 m) from the wall or screen. Use the drawing below as a guide.
Screen size (Unit: cm/inch)
406.4(W) X 304.8(H)/160"(W) X 120"(H)
365.8(W) X 274.3(H)/144"(W) X 108"(H)
304.8(W) X 228.6(H)/120"(W) X 90"(H)
243.8(W) X 182.9(H)/96"(W) X 72"(H)
203.2(W) X 152.4(H)/80"(W) X 60"(H)
162.6(W) X 121.9(H)/64"(W) X 48"(H)
121.9(W) X 91.4(H)/48"(W) X 36"(H)
81.3(W) X 61.0(H)/32"(W) X 24"(H)
61.0(W) X 45.7(H)/24"(W) X 18"(H)
Lens center
30"
40"
1.0/3.3
60"
80"
1.3/4.3
100"
120"
2.0/6.6
150"
180"
2.7/8.9
200"
3.4/11.2
Screen size
4.1/13.5
6.2/20.34
5.2/17.1
Distance (Unit: m/feet)
6.9/22.6
NOTE: The above shows the throw distance for 4:3 screen.
E-11
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and
screen. Refer to the table to determine the position of installation.
Distance Chart
Screen Height
Screen Width
Screen Diagonal
Screen center
(B)
Screen Bottom
(D)
Lens Center
Throw Angle (움)
Throw Distance (C)
B=Ve rtical distance between lens center and screen center
C=Throw distance
D=Ver tical distance between lens center and bottom of screen
α = Throw angle
4:3
Screen Size B C
Diagonal Width Height
inch
inch
inch
24
100
120
150
180
200
30
40
50
60
80
120
144
160
18
32
24
40
30
48
36
64
48
80
60
96
72
90
108
120
inch
12.6
16.8
21.0
25.2
33.6
42.0
50.4
63.0
75.6
84.0
Wide – Tele
inch
35.7 – 43.4
48.2 – 58.4
60.7 – 73.5
73.2 – 88.5
98.1 – 118.6
123.1 – 148.6
148.1 – 178.7
185.5 – 223.8
223.0 – 268.9
248.0 – 298.9
inch
12.0
14.4
18.0
21.6
24.0
D
3.6
4.8
6.0
7.2
9.6
NOTE: A 16:9 image is supported within the limits of the above values.
WARNING
* Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector severely damaged.
• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41˚F (5˚C) and 95˚F
(35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will
harm the screen image.
• Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the side or the front of
the projector.
α
Wide – Tele
degree
19.3 – 16.1
19.1 – 16.0
19.0 – 15.9
18.9 – 15.8
18.9 – 15.8
18.8 – 15.7
18.8 – 15.7
18.7 – 15.7
18.7 – 15.7
18.7 – 15.7
NOTE: Distances may vary +/–5%.
Screen Size B C
Diagonal Width Height
mm
762.0
1016.0
1270.0
1524.0
2032.0
2540.0
3048.0
3810.0
4572.0
5080.0
609.6
812.8
1016.0
1219.2
1625.6
2032.0
2438.4
3048.0
3657.6
4064.0
mm
mm
457.2
609.6
762.0
914.4
1219.2
1524.0
1828.8
2286.0
2743.2
3048.0
mm
319.8
426.5
533.3
640.0
853.4
1066.9
1280.4
1600.6
1920.8
2134.3
Wide – Tele
mm
907 – 1102
1224 – 1484
1541 – 1866
1858 – 2248
2493 – 3011
3127 – 3775
3761 – 4539
4713 – 5684
5664 – 6829
6298 – 7593
D
mm
91.2
121.7
152.3
182.8
243.8
304.9
366.0
457.6
549.2
610.3
Wide – Tele
19.3 – 16.1
19.1 – 16.0
19.0 – 15.9
18.9 – 15.8
18.9 – 15.8
18.8 – 15.7
18.8 – 15.7
18.7 – 15.7
18.7 – 15.7
18.7 – 15.7
Reflecting the Image
Using a mirror to reflect your projector's image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
you're using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or 왖왔 buttons on your remote control to correct the orientation. (See page E-41.)
α
degree
E-12
Making Connections
Wiring Diagram
Video Game
PC CONTROL
Component video cable
(RCA
⳯
3)
(Supplied)
VIDEO IN S-VIDEO IN
VCR, DVD Player or
LaserDisc Player
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
To video, S-video, and audio inputs on the projector.
SC TRIGGER
RGB IN
DVI-D IN
RGB Signal cable (supplied)
To mini D-Sub 15-pin connector on
the projector. It is recommended
that you use a commercially available distribution amplifier if connecting a signal cable longer than
the supplied cable.
DVD Player
(with component output)
Macintosh
(Desktop type or notebook type)
IBM VGA or Compatibles
(Desktop type or notebook type)
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.
E-13
Connecting Your VCR or Laser Disc Player
VIDEO AUDIO IN
or
S-VIDEO AUDIO IN
VIDEO IN
PC CONTROL
S-VIDEO IN
VIDEO IN S-VIDEO IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
Y Cb/Pb Cr/Pr
Composite video
cable (supplied)
Audio cable
(supplied)
VCR/ Laser disc player
AUDIO OUT
RL
VIDEO OUT
Audio cable (not supplied)
Use the supplied composite video cable to connect your VCR or laser
disc player to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR or laser disc player.
2. Connect one end of the composite video cable to the video output
connector on the back of your VCR or laser disc player, connect the
other end to the Video input on your projector. Use an audio cable
(not supplied) to connect the audio from your VCR or laser disc player
to your audio equipment (if your VCR or laser disc player has this
capability). Be careful to keep your right and left channel connections
correct for stereo sound.
3. Turn on the projector and the VCR or laser disc player.
COMPONENT
SC TRIGGER
DVI-D IN
RGB IN
S-video cable (supplied)
Audio equipment
AUDIO IN
LR
S-VIDEO OUT
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source
is played back in fast-forward or fast-rewind via a scan converter.
E-14
Connecting Your DVD Player
COMPONENT
AUDIO IN
COMPONENT IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
SC TRIGGER
DVI-D IN
RGB IN
PC CONTROL
VIDEO IN S-VIDEO IN
Audio cable
(supplied)
Component video RCA
⳯
3 cable
(supplied)
DVD player
AUDIO OUT
RL
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use
the supplied component video cable (RCA
player to the COMPONENT IN connectors on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a composite VIDEO output of the DVD player to the Video Input of the projector.
Use an audio cable (not supplied) to connect the audio from your
VCR or laser disc player to your audio equipment (if your VCR or
laser disc player has this capability). Be careful to keep your right and
left channel connections correct for stereo sound.
3. Turn on the projector and DVD player.
⳯
3) to connect your DVD
Audio Equipment
AUDIO IN
LR
COMPONENT OUT
Audio cable (not supplied)
NOTE: Refer to your DVD player's owner's manual for more information about
your DVD player's video output requirements,
E-15
Connecting Your PC or Macintosh Computer
Audio cable (not supplied)
PHONE
AUDIO IN
PC CONTROL
VIDEO IN S-VIDEO IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
RGB IN
SG TRIGGER
DVI-D IN
RGB IN
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recommended
that you use a commercially available distribution amplifier if connecting a signal cable longer than the supplied one.
NOTE: For older Macintosh, use
a commercially available pin
adapter (not supplied) to connect to your Mac's video port.
IBM VGA or Compatibles (Desktop type)
or Macintosh (Desktop type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the
projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer you've connected to the
projector.
For European model only
To connect SCART output (RGB)
Before connections: The supplied SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE: Audio signal is not available for this connection.
Video equipment
such as DVD player
Projector
R
E
W
O
P
S
U
T
A
T
BY
S
P
M
STAND
A
L
ON
ALIGNMENT
AUTO ADJUST
SOURCE
U
N
C
N
E
A
L
C
D
R
A
C
C
P
R
E
T
N
E
T
C
E
L
E
S
E
M
PHONE
IBM VGA or Compatibles (Notebook type)
or Macintosh (Notebook type)
NOTE: The HT1000 is not compatible with video decoded outputs of NEC ISS6020 and ISS-6010.
1. Turn off the power to the projector and your video equipment.
2. Use the supplied SCART adapter and a commercially available
SCART cable to connect the RGB input of your projector and a SCART
output (RGB) of your video equipment.
3. Turn on the power to the projector and your video equipment.
4. Use the RGB button on the remote control to select the RGB input.
5. Press the MENU button on the remote control to display the menu.
6. From the Advanced menu, select [Projector Options]
→
[Setup]
→
[Page 3] → [Signal Select RGB] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs
and DVD players. It is also referred to as Euro-connector.
Commercially available
SCART cable
To RGB IN
SCART adapter
ADP-SC1 (supplied)
E-16
Loading...