NEC Express5800-1320Xf, Express5800-1080Rf Installation Guide

Windows Server™ 2003 with SP1

Installation Guide

Version 1

855-900550-200

CONTENTS

WINDOWS SERVER™ 2003 WITH SP1................................................................................................................ 1

INSTALLATION GUIDE ..................................................................................................................................... 1

SOFTWARE INSTALLATION AND CONFIGURATION NOTES ............................................................................... 3

Before setting............................................................................................................................................ 3

BIOS Setting............................................................................................................................................. 4

PHow to install ......................................................................................................................................... 4

Installation and setup of the drivers....................................................................................................... 7

Setup for the trouble shooting ................................................................................................................. 9

Memory Dump ........................................................................................................................................ 12

Client of Remote Desktop connection feature....................................................................................... 17

Recovery of System................................................................................................................................. 20

Trouble shooting ..................................................................................................................................... 21

NEC EXPRESSBUILDER ......................................................................................................................... 23

Starting NEC EXPRESSBUILDER ...................................................................................................... 23

Troubleshooting problems...................................................................................................................... 25

ESMPRO/ServerAgent (Windows)......................................................................................................... 27

SystemGlobe GlobalMaster Agent......................................................................................................... 27

NEC ESMPRO Manager........................................................................................................................ 27

SystemGlobe GlobalMaster Manager ................................................................................................... 28

Software Installation and Configuration Notes

Before setting

z Partition size

Minimum size of the partition can be calculated from the following formula.

1635MB + paging file size + dump file size 1635MB = required for installation Paging file size (recommendation) = installed memory size x 1.5

Dump file size = installed memory size + 12MB

重要

Paging file size is required to collect debug information (memory dump). In case paging filesize is below recommendation, there might be a case that correct debug information (memory dump) can not be available.

For example, when installation size is 1024MB, minimum partition size is as follows.

1635MB + (1024MB × 1.5) + (1024MB + 12MB) = 4207MB

When partition size is smaller than “required size for installation + paging file size”,

please enlarge partition or add disks Even if enough dump file size is not available, allocation of it to several disks can be the solution.

1. Set up required size + paging file size when installation

2. Set up debug information (for dump file size) to other disk. Please refer to the later mentioned set up method for failure treatment. （If enough space to write dump file size is not available in the disk, add new disk

after installing “required size for installation + paging file size”.）

Preparation for set up

Before setting up, please prepare following disk and manual.

□ 64bit version Microsoft Windows Server 2003 Enterprise Edition CD-ROM

or 64 bit version Microsoft Windows Server 2003 Datacenter Edition CD-ROM

□ EXPRESSBUILDER CD-ROM

□ Users guide

BIOS Setting

Before you install the Windows 2003 Server, confirm the BIOS setting.

Regarding the System Interruption mode

Confirm the BIOS setting of the system interruption mode corresponding to the OS type. Regarding the BIOS setting, refer to the Hardware Guide;

"System Hardware -> Shrink total number of interrupt vectors".

If the setting is not correct, set the correct setting as follows.

Type of OS’s Value

--------------------------------------------------- -----Windows Server 2003 Datacenter Edition DISABLED Windows Server 2003 Enterprise Edition ENABLED

PHow to install

1. Power the system on

2. Set up DVD-ROM drive in the server “64bit version Microsoft Windows Server 2003 Enterprise Edition CD-ROM or 64bit version Microsoft Windows Server 2003 Datacenter Edition”

3. After setting up “64bit version Microsoft Windows Server 2003 Enterprise Edition CDROM or 64bit version Microsoft Windows Server 2003 Datacenter Edition” in DVDROM drive, please reset. (Press <Ctl> + <Alt> + <Delete>) or Power OFF/ON and reboot the server.

If you want to re-install, follow the below procedure and delete the previous

entry from EFI Boot manager, the go to step 4.

(1)Go to EFI Boot manager, select “Boot Option maintenance menu", press <Enter>. (2)Go to Main menu, select "Delete Boot Option(S)", press <Enter>. (3)Select "Windows Server 2003, Enterprise" or "Windows Server 2003, Datacenter", press <Enter>. (4)Press <Y> when "Delete selected Boot Option[Y-Yes, N-No] is shown. (5)Press <Y> when "Are you sure (Y or N)? " is shown. (6)Go to Boot Option(S), select "Exit", press <Enter>. (7)Press <Y> when "Save NVRAM?" shown. (8)Go to Main Menu and select "Exit".

4. Go to EFI Boot Manager, select "EFI Shell [Built-in]", press <Enter>. Shell screen will be shown.

5. Check the Master)/CDROM(Entry0)

"X" is "0", follow go to 6.

"X" number in fsX: fsX:Acpi(PNP0A03,0)/Pci(1F|1)/Ata(Primary,

ppy

6. Input

"fs0:」after Shell>, press <Enter>

Shell>fs0:

Command prompt will change to fs0:＼

7. Input 「setupldr」 after fs0:＼>, press <Enter>

fs0:＼>setupldr

When a SCSI/RAID adapter needs a driver other than OS standard driver, Please use the driver diskette appended to the adapter, or the driver diskette which copied the driver files of EXPRESSBUILDER inclusion, and execute OS installation in the following procedures. For details, refer to the document a ppended to the adapter, or included on EXPRESSBUILDER.

(1) Press <F6> when the following message appears on the screen.

"Press F6 if you need to install..."

(2) Press <S> to specify an additional device when the following message appears on the screen.

Setup could not determine the type of one or more mass storage devices installed in your system, or you have chosen to manually specify an adapter. Currently, Setup will load support for the following mass storage devices(s):

(3) Insert the driver diskette and press <Enter> when the following message appears on the

screen.

Manufacturer-supplied hardware support disk

Please insert the disk labeled

into Drive A:

* Press ENTER when ready.

(4) Select the appropriate driver from the list by arrow key. Press <Enter> to proceed. (5) Press <S> when the following message appears on the screen. And advance the OS

installation according to message of the screen.

The driver you provided seems to be older than the Windows default driver. : :

S=Use the driver on flo

ENTER=Use the default Windows drive

(6) Press <Enter> when the reading from the Driver FD device is finalized, continue setup.

When following dialog is shown, press [OK] and continue

8. Continue set up following the message and complete installation.

When following message is shown, press [Enter] and continue. "System partition can not be found" At the initial set up, Hard disk configuration is as follows. Please do not delete

"Partition 1[FAT] " and "Partition 2[reserved]".

Partition1

Do not delete

Partition2

Open area

When the installation is completed, Windows Server 2003 Hot fixes are required to be installed. Please ask sales representative for details.

Installation and setup of the drivers

This section describes installation and setup of the standard devices' drivers. After completion of the driver setup, go to "Setup for the trouble shooting" section.

The device developed by NEC

Installation of the driver for the device developed by NEC is executed from "Software Setup Menu" of NEC EXPRESSBUILDER.

1. Insert the NEC EXPRESSBUILDER CD-ROM in the CD-ROM drive.

The NEC EXPRESSBUILDER Master Control Menu appears.

2. Select the “Setup”.

The Software Setup Menu appears.

3. Click “th e dev ice developed by NEC” to run the set up program.

4. Click [Open], if the [download] dialog box appeard.

5. When the [installation completed] dialog appears, click [OK].

The driver installation for devices developed by NEC is completed.

Other devices

Installation and setup of the driver for other devices, please refer to the document attached to the device, and provided in the NEC EXPRESSBUILDER CD-ROM.

Be sure to update a driver according to the document, although Windows standard driver will be installed automatically in these devices. System may become unstable unless the driver has not updated.

The standard devices which are listed below, use Windows standard driver.

Network device (Additional Setup)

Set up link speed and Duplex mode after installing a network driver.

Floppy disk drive

・

DVD-ROM drive (ATAPI)

・

USB

・

COM port

・

Mouse

・

Keyboard

・

System devices

・

If you deleted the network driver, reboot the system. Then, network drivers will be installed automatically.

· We recommend you to add a [network monitor] from [Add/Remove Windows Components] of

a control panel. The network monitor can supervise the message sending/receiving frame (or packet) of a computer on which it is installed. It is a tool effective in the analysis of a network obstacle etc. Refer to the section of "Setup of obstacle processing" next to this part. Here is the procedure, provided it is indicated in the described way.

- Select "taskbar's properties" and "Start Menu" tab, click "Classic Start menu".

- Select "explorer's folder options", click "Show common tasks in folders".

- Select “display’s properties” and “Setting” tab, select “Windows Classic style” from

“windows and buttons” pull-down menu.

1. Click Start menu, Click [Settings] and Click

[Network Connections]. The [Network Connections] dialog box appears.

2. Right-click [Local Area Connection] and click

[Properties] from pop-up menu. The [Local Area Connection Properties] dialog box appears.

3. Click [Configure].

The property dialog box for network adapter appears.

4. Select [Advanced] tab and set the [Link Speed

& Duplex] value the same as the value specified for HUB.

5. Click [OK] on the property dialog box for

network adapter.

The network driver setup is completed.

Setup for the trouble shooting

In order to recover the system from the unexpected trouble, please finish the following setup in advance. When you finish the following setup, please go on with the section

重要.

of "Installation of Management utility".

Here is the procedure, provided it is indicated in the described way.

- Select "taskbar's properties" and "Start Menu" tab, click "Classic Start menu".

- Select "explorer's folder options", click "Show common tasks in folders".

- Select “display’s properties” and “Setting” tab, select “Windows Classic style”

from “windows and buttons” pull-down menu.

Setup of the Backup Tool

The periodical backup by the OS standard backup tool (Ntbackup) or other backup tools on market is highly recommended. Please send your inquiries to the shop where you bought the tool or the service company for the details about the backup tool which could be used in this equipment.

Setup of Memory Dump (Information for Debug)

This setup is for collecting the Memory Dump (Information for Debug) of the server.

Notice for the Memory Dump

z The collection of Memory Dump could be done only by the workers of the

service company. Please set up the memory dump only yourself.

z After the setup introduced here, if the machine is rebooted to keep the

memory dump while trouble occurs, sometimes the message of insufficient virtual memory appears. Please go on with your reboot. After the reboot, sometimes the memory dump could be kept correctly.

It is necessary to reset the memory dump when the memory is enhanced.

+ 19 hidden pages