How it Works
Nec
Loading...
60004827
User Manual
76 pgs13.21 Mb0
Quick Start Guide
5 pgs1.99 Mb0
Product Data Sheet
4 pgs123.44 Kb0
Table of contents
Loading...

Nec 60004827 User Manual

User’s Manual
Large Format Display
MultiSync V554Q
MODEL: V554Q
Please find your model name in the label on the rear side of monitor.
Index
Registration Information .................................................................................................................................................... English-1
Important Information ........................................................................................................................................................ English-2
WARNING .......................................................................................................................................................... English-2
CAUTION ........................................................................................................................................................... English-2
Safety Precautions, Maintenance & Recommended Use .................................................................................................English-3
Safety Precautions and Maintenance ................................................................................................................English-3
Recommended Use ...........................................................................................................................................English-3
Ergonomics ........................................................................................................................................................English-3
Cleaning the LCD Panel ....................................................................................................................................English-4
Cleaning the Cabinet .........................................................................................................................................English-4
Installation ......................................................................................................................................................................... English-5
Attaching Mounting Accessories ........................................................................................................................ English-7
Parts Name and Functions ................................................................................................................................................ English-9
Control Panel .....................................................................................................................................................English-9
Setup .................................................................................................................................................................................English-14
Connections ......................................................................................................................................................................English-16
Basic Operation ................................................................................................................................................................. English-19
OSD (On-Screen-Display) Controls ..................................................................................................................................English-31
Remote Control Functions .................................................................................................................................................English-46
Multiple Monitors Connection ............................................................................................................................................English-47
Controlling the monitor via RS-232C Remote Control ....................................................................................................... English-48
Controlling the monitor via LAN Control .............................................................................................................................English-50
POINT ZOOM .................................................................................................................................................................... English-58
PROOF OF PLAY .............................................................................................................................................................. English-59
INTELLIGENT WIRELESS DATA ...................................................................................................................................... English-60
MULTIPICTURE matrix .....................................................................................................................................................English-60
Video out ........................................................................................................................................................................... English-67
Features ............................................................................................................................................................................ English-68
Troubleshooting ................................................................................................................................................................. English-69
Specifications - V554Q ...................................................................................................................................................... English-71
Manufacturer’s Recycling and Energy Information............................................................................................................ English-72
[Notice] About the MPEG-4 AVC, MPEG-4 Visual license included in this product ........................................................... English-74

Registration Information

Cable Information
CAUTION: Use the provided specified cables with this product so as not to interfere with radio and television reception.
For USB, please use a shielded signal cable with ferrite core. For D-Sub 9-Pin, HDMI and DisplayPort, please use a shielded signal cable. Use of other cables and adapters may cause interference with radio and television reception.
FCC Information
WARNING: The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by
NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.
SUPPLIER’S DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 3250 Lacey Rd, Ste 500 Downers Grove, IL 60515 Tel. No.: (630) 467-3000
Type of Product: Display Monitor Equipment Classification: Class B Peripheral
Model: V554Q
English
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. MultiSync is a trademark or registered trademark of NEC Display Solutions, Ltd. in Japan and other countries. DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video Electronics Standards Association in the
United States and other countries. All other brands and product names are trademarks or registered trademarks of their respective owners. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries. Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other
countries and areas. microSD and microSD SDHC logos are trademarks of SD-3C, LLC. CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of Crestron Electronics, Inc.
in the United States and other countries. Raspberry Pi is a trademark of the Raspberry Pi Foundation. Adobe and the Adobe logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other
countries.
GPL/LGPL Software Licenses
The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL), and others. For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.
English-1

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this device in accordance with the table below. If a power cord is not supplied with this equipment, please contact NEC. For all other cases, please use the power cord with the plug style that matches the power socket where the monitor is located. The compatible power cord corresponds to the AC voltage of the power outlet and has been approved by, and complies with, the safety standards in the country of purchase.
This equipment is designed to be used with a power cord that has a protective earth pin connected to earth. If the power cord is not connected to the earth, it may cause electric shock. Please make sure the power cord is earthed properly.
Plug Type North America
Plug Shape
Region
Voltage
* When operating this monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply
voltage of the AC power outlet being used.
NOTE: This product can only be serviced in the country where it was purchased.
Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.
• TheintendedprimaryuseofthisproductisasanInformationTechnicalEquipmentinanofceordomesticenvironment.
• Theproductisintendedtobeconnectedtoacomputerandisnotintendedforthedisplayoftelevisionbroadcastsignals.
U.S.A./
Canada
120*
Taiwan
110
European
Continental
EU U.K. China Japan
230 230 220 100
U.K. Chinese Japanese
English-2

Safety Precautions, Maintenance & Recommended Use

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
• DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.
• Donotbend,crimporotherwisedamagethepowercord.
• Donotplaceanyheavyobjectsonthepowercord.
Damage to the cord may cause shock or fire.
• Fastenthepowercordtothemonitorbyattachingthe
screw and clamp to prevent loose connection.
(RecommendedFastenForce:139-189N•cm).
• Pleasemakesurethatenoughpowerissuppliedto
the monitor. Please refer to the “Power Supply” in the specifications.
• Thepowersupplycordyouusemusthavebeen
approved by and comply with the safety standards of your country. (e.g. Type H05VV-F 3G 0.75 mm2 should be used in Europe).
• IntheUKuseaBS-approvedpowercordwithamolded
plug having a black (5 A) fuse installed for use with this monitor.
• Thepowercableconnectoristheprimarymeansof
detaching the system from the power supply. The monitor should be installed close to a power outlet that is easily accessible.
• Donotspillanyliquidsintothecabinetoruseyour
monitor near water.
• Donotinsertobjectsofanykindintothecabinetslots,
as they may touch dangerous voltage points, which can be harmful or fatal, or may cause electric shock, fire or equipment failure.
• Donotplacethisproductonaslopingorunstablecart,
stand or table, as the monitor may fall, causing serious damage to the monitor.
• Donotmountthisproductupsidedownforanextended
period of time as it may cause permanent damage to the screen.
• Donotusethemonitoroutdoors.
• Ifglassisbroken,handlewithcare.
•
This monitor is equipped with temperature control fans. For reliable performance and long life use of this product, it is required that the vents on the monitor are not covered.
• Ifthemonitororglassisbroken,donotcomeincontact
with the liquid crystal and handle with care.
• Allowadequateventilationaroundthemonitor,sothat
heat can properly dissipate.
• Donotblockventilatedopeningsorplacethemonitor
near a radiator or other heat sources.
• Donotputanythingontopofthemonitor.
• Handlewithcarewhentransporting.Savepackagingfor
transporting.
• Whenrunningthecoolingfancontinuously,we
recommend wiping clean the ventilation holes a minimum of once a month.
• To ensure the monitor’s reliability, please clean the
ventilation holes at the rear side of the cabinet at least once a year to remove dirt and dust.
• WhenusingaLANcable,donotconnecttoaperipheral
device with wiring that might have excessive voltage.
• Donotusethemonitorinhightemperature,humid,dusty,
or oily areas.
• Donotusethemonitorunderrapidchangesin
temperature and humidity, and avoid cold air directly from an air-conditioning vent. These conditions may shorten the life of the monitor or cause condensation. If water condensation has occurred, unplug the monitor and do not use the monitor until the condensation has evaporated.
Connecting to a TV*
• Cabledistributionsystemshouldbegrounded(earthed)
in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
• Thescreenofthecoaxialcableisintendedtobe
connected to earth in the building installation.
Under the following conditions immediately disconnect your monitor from the wall outlet and refer servicing to qualified service personnel:
• Ifthepowersupplycordorplugisdamaged.
• Ifliquidhasspilled,orobjectshavefallenintothemonitor.
• Ifthemonitorhasbeenexposedtorainorwater.
• Ifthemonitorhasbeendroppedorthecabinethasbeen
damaged.
• Ifyounoticeanystructuraldamagesuchascracksor
unnatural wobbling.
• Ifthemonitordoesnotoperatenormallybyfollowing
operating instructions.

Recommended Use

Ergonomics

To realize the maximum ergonomic benefits, we recommend the following:
• Forthemonitor’soptimumperformance,allow20minutes
for warming up. Avoid reproduction of still patterns on the monitor for long periods of time to avoid image persistence (after image effects).
• Restyoureyesperiodicallybyfocusingonanobjectat
least 5 feet away. Blink often.
• Positionthemonitorata90°angletowindowsandother
light sources to minimize glare and reflections.
• Adjustthemonitor’sbrightness,contrastandsharpness
controls to enhance readability.
• Getregulareyecheckups.
• UsethepresetSizeandPositioncontrolswithstandard
input signals.
• Usethepresetcolorsettings.
• Usenon-interlacedsignals.
• Donotviewtheprimarycolorblueonadarkbackground.
It is difficult to see and may cause eye fatigue due to insufficient contrast.
• Suitable for entertainment purposes at controlled luminous environments, to avoid disturbing reflections from the screen.
* The product you purchased may not have this feature.
English
English-3

Cleaning the LCD Panel

• WhentheLCDpanelisdusty,pleasegentlywipewitha
soft cloth.
• CleantheLCDmonitorsurfacewithalint-free,non-
abrasive cloth. Avoid using any cleaning solution or glass cleaner!
• PleasedonotrubtheLCDpanelwithahardorabrasive
material.
• PleasedonotapplypressuretotheLCDpanelsurface.
• PleasedonotuseOAcleanerasitwillcause
deterioration or discoloration on the LCD panel surface.

Cleaning the Cabinet

• Unplugthepowersupply.
• Gentlywipethecabinetwithasoftcloth.
• Tocleanthecabinet,dampentheclothwithaneutral
detergent and water, wipe the cabinet and follow with a dry cloth.
NOTE: DO NOT clean with benzene thinner, alkaline
detergent, alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Rubber or vinyl should not be in contact with the cabinet for an extended period of time. These types of fluids and materials can cause the paint to deteriorate, crack or peel.
English-4

Installation

For box contents, please refer to the printed contents sheet provided in the box.
This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty.
Mounting
CAUTION
For customer:
DO NOT mount the monitor yourself. For proper installation it is strongly recommended to use a trained, qualified technician. Please contact your supplier, as they may be able to provide a list of qualified installation professionals. Mounting on a wall or ceiling and hiring a technician is the customer’s responsibility.
Maintenance
• Periodicallycheckforloosescrews,gaps,distortions,
or other problems that may occur with the mounting equipment. If a problem is detected, please refer to qualified personnel for service.
• Regularlycheckthemountinglocationforsignsof
damage or weakness that may occur over time.
DO NOT block ventilated openings with mounting accessories or other accessories.
For NEC Qualified Personnel:
Stability Hazard.
The device may fall, causing serious personal injury or death. To prevent injury, this device must be securely attached to the floor/wall in accordance with the installation instructions.
Carefully inspect the location where the unit is to be mounted. Not all walls or ceilings are capable of supporting the weight of the unit. Weight of this monitor is mentioned in Specification (see “V554Q” on page 71). Product warranty does not cover damage caused by improper installation, re­modeling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty.
To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location.
Please note the following when mounting on wall or ceiling
CAUTION
• Whenusingmountingaccessoriesotherthanthosethat
are NEC approved, they must comply with the VESA­compatible (FDMlv1) mounting method.
• NECrecommendsmountinginterfacesthatcomplywith
UL1678 standard in North America.
• NECstronglyrecommends
using size M6 screws (10-12 mm + thickness of bracket and washers in length). If using screws longer than 10-12 mm, check the depth of the
under
8.5 mm
Unit
No thread
4 mm
10-12 mm
No gap
hole. (Recommended Fasten
Force:470-635N•cm).Bracket
hole should be under 8.5 mm.
• Priortomounting,inspecttheinstallationlocationto
ensure that it is strong enough to support the weight of the unit so that the unit will be safe from harm.
• For detailed information, refer to the instructions included with the mounting equipment.
• Make sure that there is no gap between the monitor and the bracket.
NOTE: When used in a video wall configuration for a long
time, slight expansion of the monitors may happen due to temperature changes. It is recommended that over one millimeter gap is kept between adjacent monitor edges.
CAUTION: • Wheninstalling,donotapplypressureto
the LCD panel or excessive force to any part of the monitor by pushing or leaning on it. This may cause the monitor to become distorted or damaged.
• To prevent the monitor from falling off from the wall or ceiling, NEC strongly recommends using a safety wire.
• Please install monitor in a spot of the wall or ceiling strong enough to support the monitor.
• Prepare the monitor using mounting accessories such as hook, eyebolt or mounting parts and then secure the monitor with a safety wire. The safety wire must not be tight.
• Donotattempttohangthemonitorusing an installation safety wire. The monitor must be properly installed on a VESA compatible mount.
• Please make sure the mounting accessories are strong enough to support the monitor before mounting it.
Mounting Bracket
Washers
Screw
Thickness of bracket and washers
English
English-5
Please use the handles for landscape position and the two mounting holes with using eyebolts for portrait position.
Safety wire for landscape position
VESA Mounting Interface (M6)
Installing a wire to a monitor for portrait position
Please use eyebolts to install a wire to the monitor. To prevent the monitor from falling off from the wall or ceiling, NEC strongly recommends using a wire.
Please install the monitor in a spot of the wall or ceiling strong enough to support the monitor.
Safety wire for
portrait position
10-12 mm
Mounting location
• Theceilingandwallmustbestrongenoughtosupportthe
monitor and mounting accessories.
• DONOTinstallinlocationswhereadoororgatecanhit
the unit.
• DONOTinstallinareaswheretheunitwillbesubjected
to strong vibrations and dust.
• DO NOT install the monitor next to a location where the main power supply is fed into the building.
• DO NOT install the monitor in a location where people can easily grab and hang onto the unit or the mounting equipment.
• Allow for adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the monitor and from the mounting equipment.
Mounting on ceilings
• Ensurethattheceilingisstrongenoughtosupportthe
weight of the unit and the mounting equipment over time, against earthquakes, unexpected vibrations, and other external forces.
• Besuretheunitismountedtoasolidstructurewithin
the ceiling, such as a support beam. Secure the monitor using bolts, spring lock washers, washer and nut.
• DONOTmounttoareasthathavenosupportinginternal
structure. DO NOT use wood screws or anchor screws for mounting. DO NOT mount the unit to ceiling or to hanging fixtures.
Maintenance
• Periodicallycheckforloosescrews,gaps,distortions,
or other problems that may occur with the mounting equipment. If a problem is detected, please refer to qualified personnel for service.
• Regularlycheckthemountinglocationforsignsof
damage or weakness that may occur over time.
Orientation
• Whenusingthemonitorintheportraitposition,itshould
be rotated clockwise so that the left side is moved to the top, right side is moved to the bottom. This will allow for proper ventilation and will extend the lifetime of the monitor. Improper ventilation may shorten the lifetime of the monitor.
LED Indicator
English-6
Changing NEC logo ornament position
When using the monitor in the portrait position, the NEC logo ornament position can be changed.
Removing the logo ornament: unscrew the installed screw then take off the logo ornament.
Attaching the logo ornament: adjust the protrusions inside of the logo ornament into the protrusion holes on the bezel. Make sure the hole for the screw on the logo ornament and the hole for the screw on the bezel are aligned. Install the logo ornament with the screw, which is used for installing the logo ornament. (Recommended Fasten Force: 30-40N•cm).
Screw hole
Protrusion hole
Protrusion
Inside of NEC logo ornament
Protrusion hole
Screw hole
Protrusion
When using mounting accessories other than NEC compliant and approved, they must comply with the VESA Flat Display Mounting Interface Standard (FDMI).
NOTE: Prior to installation, place the monitor face down
on a flat even surface that is larger than the monitor screen. Use a sturdy table that can easily support the weight of the monitor.
2. Installing an Option Board
1. Turn off the main power switch.
2. Place the monitor face down on the protective sheet.
NOTE: Be sure to place the monitor on a flat and adequate space.
3. Remove the attached slot cover by unscrewing the
installed screws (Figure 1), sliding to right (Figure 2) and moving up (Figure 3).
English
CAUTION: Do not use any other screw to install the logo
ornament.

Attaching Mounting Accessories

The monitor is designed for use with the VESA mounting system.
1. Attach Mounting Accessories
Be careful to avoid tipping the monitor when attaching accessories.
VESA Mounting Interface (M6)
300 mm
300 mm
Mounting accessories can be attached with the monitor in the face down position. To avoid scratching the LCD panel, always place a soft cloth, such as a blanket that is larger than the monitor’s screen area, on the table before laying the monitor face down. Make sure there is nothing on the table that can damage the monitor.
Figure 1 Figure 2
Figure 3 Figure 4
4. Insert the Option Board into the monitor and fix it with the
removed screws (Figure 4).
NOTE: Please contact your supplier for a list of Option
Boards available for your monitor. Do not apply excessive force to manipulate the Option Board before fixing it with screws. Make sure that the board is inserted into the slot in the correct orientation.
WARNING: Ensure the Option Board is attached by the
removed screws. Otherwise, the Option Board may fall out and expose you to danger.
(RecommendedFastenForce:139-189N•cm).
English-7
3. Installing and Removing the Optional
100 mm
100 mm
30 mm
100 mm
100 mm
Table Top Stand
CAUTION: • Installingandremovingthestandmustbe
done by two or more people.
• ONLYusescrewswhicharesuppliedwith the optional table top stand.
• Wheninstallingthemonitorstand,handle the unit with care to avoid pinching your fingers.
For installation, follow the instructions included with the stand or mounting equipment. Use only those devices recommended by the manufacturer.
NOTE: • UsetheST-401.PleaserefertotheST-401
user’s manual for more detail.
• DO NOT use this monitor on the floor with the table top stand. Please use this monitor on a table or with a mounting accessory for support.
CAUTION: Please refer to the table top stand manual of
ST-401 for “structure of Prevent Tipping”.
300 mm
2. Please install the stand pole and the pipe with included
screws. Please screw the two screw holes at the pipe (Figure 4).
Pipe
Stand pole
Figure 4
CAUTION: Installing the monitor at the wrong height can
cause tipping. Please install your monitor at proper height.
4. Ventilation Requirements
When mounting in an enclosed space or recessed area, leave adequate room between the monitor and the enclosure to allow heat to disperse, as shown below.
Height adjustment
1. The lines on the stand pole are indicators of the height adjustment (Figure 3). Please adjust the pipe to the lines.
Pipe
V554Q High/Low
Adjust the pipe to a line.
Figure 3
Must be under 40 Degree Celsius.
Allow adequate ventilation or provide air conditioning around the monitor, so that heat can properly dissipate away from the unit and the mounting equipment; especially when you use monitors in a multiple screen configuration.
NOTE: The sound quality of the internal speakers will be
different depending on the acoustics of the room.
English-8

Parts Name and Functions

Control Panel

A Button (power button)
Switches the power on/standby. See also page 19.
B MUTE Button
Switches the audio mute on/off.
C INPUT/SET Button
INPUT: Cycles through the available inputs when OSD menu is turned off. [DisplayPort1], [DisplayPort2], [HDMI1], [HDMI2], [HDMI3], [MP], [OPTION*], [C MODULE]* are available inputs only, shown as their factory preset name. NOTE: MP is an abbreviation of Media Player. SET: Acts as a “set” button when making a selection when the OSD (On Screen Display) menu is open. *: This function depends on which Option Board you are using. *1: This input is available when the optional Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute Module are installed.
D + Button (plus button)
Increases the audio output level when the OSD menu is turned off. Acts to move the highlighted area to the right when navigating through the OSD menu options. Acts as (+) to increase the adjustment of an OSD menu option after it has been selected with the SET button.
E - Button (minus button)
Decreases the audio output level when the OSD menu is turned off. Acts to move the highlighted area to the left when navigating through the OSD menu options. Acts as (-) to decrease the adjustment of an OSD menu option after it has been selected with the SET button.
1
. These
F p Button (up button)
Activates the OSD menu when the OSD menu is turned off. Acts as p button to move the highlighted area up to select adjustment items within the OSD menu.
G q Button (down button)
Activates the OSD menu when the OSD menu is turned off. Acts as q button to move the highlighted area down to select adjustment items within the OSD menu.
H MENU/EXIT Button
Activates the OSD menu when the OSD menu is turned off. Acts as a back button within the OSD to move to the previous OSD menu. Acts as an EXIT button to close the OSD when on the main menu.
I Remote Control Sensor and Power Indicator
Receives the signal from the remote control (when using the wireless remote control). See also page 13. Glows blue when the monitor is in active mode*. Green and Amber blink alternately when the [SCHEDULE SETTINGS] function is enabled* When a component failure is detected within the monitor, the indicator will blink red or blink a combination of red and blue. *: If [OFF] is selected in the [POWER INDICATOR]
page 42
(see active mode. *1: If [OFF] is selected in the [SCHEDULE INDICATOR] (see
page 42
NOTE: Please refer to the [POWER INDICATOR] (see page 42).
), the LED will not glow when the monitor is in
), the LED will not blink.
1
.
J Room Light Sensing Sensor
Detects the level of ambient light, allowing the monitor to make automatic adjustments to the backlight setting, resulting in a more comfortable viewing experience. Do not cover this sensor. See page 42.
English
English-9

Terminal Panel

USB Upstream
A AC IN Connector
Connects with the supplied power cord.
B Main Power Switch
On/Off switch to turn main power ON/OFF.
C Audio IN
Audio signal input from external equipment such as a computer or player.
D DisplayPort OUT
Output DisplayPort signals from DisplayPort IN1. You can connect multiple monitors by using DisplayPort daisy-chain connection. See [MULTI DISPLAY] (page 38) and Video out (page 67).
E DisplayPort IN1/IN2
DisplayPort signals input.
F HDMI IN1/IN2/IN3
HDMI signals input.
G RS-232C IN (D-Sub 9 pin)
Connect RS-232C input from external equipment, such as a computer, in order to control RS-232C functions. See page 48.
H Remote IN
Use the optional sensor unit by connecting it to your monitor. NOTE: Do not use this connector unless specified.
I microSD Card Slot
microSD memory card reader for use with the Media Player (See page 22). To install the microSD card slot cover, please refer to “Installing microSD card slot cover” (See page 22).
J USB Port
USB1: Downstream port (USB Type-A). Connect USB devices. USB2: Upstream port (USB Type-B). Connect external equipment such as a computer. To control the monitor from connected external equipment, please use this port. USB CM1 (2A): Power supply port. USB CM2*: Service port. Please do not connect devices. * USB functionality is available when the optional Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute Module are installed. USB MP: USB storage device reader for use with the Media Player. See page 21. This port is for future software upgrades. To use the Media Player, please connect USB storage device to this port (See page 18). MP is an abbreviation of Media Player.
K LAN Port 1/2 (RJ-45)
Connect to LAN in order to manage and control the monitor over the network. See page 47 and page 50. NOTE: Please give priority for use to LAN1.
L Audio OUT
Audio signal output from the AUDIO IN, DisplayPort and HDMI to an external device (stereo receiver, amplifier, etc.). NOTE: This connector is not a Headphone terminal.
M Internal/External Speaker Switch
: Internal speaker : External speaker. NOTE: Please turn off the monitor’s main power when you use the Internal/External speaker switch.
N External Speaker Terminal
Audio signal output. Red terminal is plus (+). Black terminal is minus (-). NOTE: This speaker terminal is for 15 W + 15 W (8 ohm) speaker.
English-10
O Internal Speaker P Option Board Slot
Slot for installation of a Slot 2 type Option Board. See page 7. NOTE: Please contact your supplier for a list of compatible Option Boards.
Q Security Slot
Security and theft protection lock slot compatible with Kensington security cables/equipment. For products, visit Kensington’s website.
R Rating Label S Intelligent Wireless Data Sensor
Sensor for wireless communication to the monitor for information and settings. See page 60.
T Option Speaker Mounting Hole
NOTE: Please contact your supplier for a list of compatible speakers.
Raspberry Pi Compute Module Slot
Slot for installing a Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute Module. Please refer to https://www.nec-display.com/dl/en/manual/raspberrypi/ for more information.
CAUTION: Installation must be performed by a qualified
technician. Do not attempt to install a Compute Module Interface Board and Raspberry Pi Compute Module by yourself.
English
English-11

Wireless Remote Control

I p/q Button (up/down button)
Acts as pq button to move the highlighted area up or down to select adjustment items within the OSD menu. When using PIP (picture in picture), moves the small screen up or down.
J -/+ Button (minus/plus button)
Increases or decreases the adjustment level within the OSD menu settings. When using PIP (picture in picture), moves the small screen left or right.
K SET/POINT ZOOM Button
SET: When OSD is shown, this button acts as “set button” when you make a selection. POINT ZOOM: When OSD is not shown, this button acts as “point zoom button”.
L VOLUME +/- Button
Increases or decreases the audio output level.
A POWER ON/STANDBY Button
Switches the power on/standby.
B INPUT Button
Selects the input signal. Input signal for the MEDIA PLAYER is shown as MP.
C OPTION MENU Button D KEYPAD
Press the buttons to set and change passwords, change channel and set REMOTE ID. The following buttons are used for [CEC] (Consumer Electronics Control) (See page 43) and the Media Player function (See page 21): 1 , 2 , 3 , 5 , 6 .
E ENT Button
Confirm the AUTO PLAY FOLDER in Media Player.
M CH/ZOOM +/- Button*
Increases or decreases the POINT ZOOM level. Please refer to POINT ZOOM (See page 58).
N GUIDE Button*
1
1
O MUTE Button
Turns on/off the mute function.
P PICTURE MODE Button
Selects the picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1], [CUSTOM2], [SVE-(1-5) SETTINGS]. See page 30.
HIGHBRIGHT: For moving images such as DVD. STANDARD: For images. sRGB: For text based images. CINEMA: For movies. CUSTOM1 and CUSTOM2: Custom setting. SVE-(1-5) SETTINGS: For images and movies.
Q ASPECT Button
Selects the picture aspect, [FULL], [WIDE]*, [DYNAMIC]*, [1:1], [ZOOM] and [NORMAL]. See page 20.
* HDMI1, HDMI2, HDMI3 inputs only.
R AUDIO INPUT Button
Selects the audio input source [IN], [HDMI1], [HDMI2], [HDMI3], [DisplayPort1], [DisplayPort2], [OPTION]*1, [MP], [C MODULE]*2.
F DISPLAY Button
Turns on/off the information OSD. See page 27. If you lock remote control buttons using the [IR LOCK SETTINGS] function, you can unlock the buttons by holding down this DISPLAY button for more than 5 seconds.
G MENU Button
Turns on/off the menu mode.
H EXIT Button
Returns to the previous menu within the OSD menu.
S STILL Button
ON/OFF Button: Activates/deactivates still picture mode. CAPTURE Button: Captures still picture. NOTE: This function deactivates when selecting [MULTI
PICTURE MODE], [TEXT TICKER], [SCREEN SAVER], POINT ZOOM, [IMAGE FLIP] except for [NONE], [SUPER] in [INPUT CHANGE], [TILE MATRIX]. If input signal is [OPTION], this button’s actions depend on which Option Board you are using.
*1: This button’s action depends on which Option Board you are using. *2: This input is available when the optional Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute Module are installed.
English-12
T IMAGE FLIP Button
Toggleswitchesbetween[HFLIP],[VFLIP],[180°ROTATE]
and [NONE]. See page 34.
ACTIVE PICTURE Button
Selects active picture.
MULTI PICTURE Button
ON/OFF Button: Toggle switches between ON and OFF. MODE Button: Selects a mode from PIP (picture in picture)
or PBP (picture by picture).
CHANGE Button: Swaps images between two pictures. PICTURE ASPECT Button: Selects active picture frame
aspect. NOTE: Enable to change each multi picture size by pressing SET/POINT ZOOM button during multi picture mode.
REMOTE ID Button
Activates the REMOTE ID function. See page 46.
MTS Button*
1

Operating Range for the Remote Control

Point the top of the remote control toward the monitor’s remote control sensor during button operation.
Use the remote control within a distance of about 7 m (23 ft.) from the remote control sensor, or at a horizontal and
verticalangleofwithin30°andwithinadistanceofabout
3.5 m (10 ft.).
English
*1: This button’s action depends on which Option Board you are using. Refer to the Option Board’s user’s manual for further information.
NOTE: The buttons with no explanation do not function.
NOTE: The remote control system may
not function when direct sunlight or strong illumination strikes the remote control sensor, or when there is an object in the path.
Handling the remote control
• Donotexposetostrongshock.
• Donotallowwaterorotherliquidto
splash on the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoidexposuretoheatandsteam.
• Excepttoinstallthebatteries,donotopentheremote
control.
English-13

Setup

1. Determine the installation location
CAUTION
• Installingyourmonitormustbedonebyaqualied
technician. Contact your supplier for more information.
• MOVINGORINSTALLINGTHEMONITORMUSTBE
DONE BY TWO OR MORE PEOPLE. Failure to follow this caution may result in injury if the monitor falls.
• Donotmountoroperatethemonitorupsidedown.
NOTE: This monitor has internal temperature sensors and
cooling fans, including a fan for the Option Board. If the monitor becomes too hot, the cooling fans will turn on automatically. The Option Board’s fan is active although the temperature is lower than normal operating temperature for cooling the Option Board. If the monitor becomes overheated while the cooling fan is running, a “Caution” warning appears. If the “Caution” warning appears, stop using the unit, turn off the power and allow it to cool. Using the cooling fans will reduce the likelihood of early unit failure and may help reduce image degradation and “Image Persistance”.
CAUTION: If the monitor is used in an enclosed
area or if the LCD panel is covered with a protective screen, please check the inside temperature of the monitor by using the [HEAT STATUS] control in the OSD (see page 40). If the temperature is higher than the normal operating temperature, please turn the cooling fan to [ON] within the [FAN CONTROL] menu within the OSD (see page 40).
NEC recommends the following battery use:
• Place“AAA”sizebatteriesmatchingthe(+)and(-)signs
on each battery to the (+) and (-) signs of the battery
compartment.
• Donotmixbatterybrands.
• Donotcombinenewandoldbatteries.Thiscanshorten
battery life or cause liquid leakage of batteries.
• Removedeadbatteriesimmediatelytopreventbattery
acid from leaking into the battery compartment.
• Donottouchexposedbatteryacid,itmayinjureyourskin.
NOTE: If you do not intend to use the Remote Control for
a long period of time, remove the batteries.
3. Connect external equipment (See page 16, page 17 and page 18)
• Toprotecttheexternalequipment,turnoffthemainpower
before making connections.
• Refertothe user’s manual of your equipment for further
information. NOTE: Do not connect/disconnect cables when turning
on the monitor or other external equipment as this may result in a loss of the monitor image.
4. Connect the supplied power cord
The monitor should be installed close to an easily accessible power outlet.
CAUTION: Fasten the power cord to the monitor
by attaching the screw and clamp. (Recommended Fasten Force: 139 -189N•cm).
IMPORTANT: To avoid scratching the LCD panel, always
place a soft cloth, such as a blanket that is larger than the monitor’s screen area, on the table before laying the monitor face down.
2. Install the remote control batteries
The remote control is powered by two 1.5V AAA batteries. To install or replace batteries:
1. Press and slide to open the cover.
2. Align the batteries according to the (+) and (–) indications inside the case.
3. Replace the cover.
CAUTION: Incorrect usage of batteries can result in
leaks or bursting.
WARNING: • Pleaserefertothe“Important Information”
section of this user’s manual for proper selection of an AC power cord.
• Fullyinserttheprongsintothepower outlet socket. A loose connection may cause image instability and may pose a fire hazard.
Screw
Clamp
English-14
5. Cable information
CAUTION: Use the provided specified cables with this
product so as not to interfere with radio and television reception. For USB, please use a shielded signal cable with ferrite core. For D-Sub 9-pin, HDMI and DisplayPort, please use a shielded signal cable. Use of other cables and adapters may cause interference with radio and television reception.
6. Turn on the power for the external
equipment and the monitor
When connected to a computer, switch on the monitor power first.
7. Operate the attached external equipment
Select the input source for the attached equipment to show the image signal on screen.
8. Adjust the sound
Make volume adjustments when required.
9. Adjust the picture settings (See page 32)
If necessary, make adjustments to such as the backlight or contrast in the OSD [PICTURE] menu.
English
10. Recommended Adjustments
To reduce the risk of the “Image Persistence”, please adjust the following items based on the application being used: [SCREEN SAVER], [SIDE BORDER COLOR] (See page 40), [DATE & TIME] (See page 35), [SCHEDULE SETTINGS] (See page 35). It is recommended that the [FAN CONTROL] setting (See page 40) be checked [ON] also.
English-15

Connections

USB1
USB2
USB CM1 (2A)
USB CM2
USB MP
NOTE: Do not connect or disconnect cables when turning on the monitor’s main power or other external equipment’s power
as this may result in a loss of image.
NOTE: Do not use an attenuating (built-in resistor) audio cable. Use an audio cable without a built-in resistor. Using an audio
cable with a built-in resistor will lower the sound level.
Before making connections:
* Turn off the device’s power before connecting it to the monitor. * Refer to the device’s user manual for available connection types and instructions for the device. * We recommend turning off the monitor’s main power before connecting or disconnecting a USB storage device or a microSD
memory card to avoid data corruption.

Wiring Diagram

Stereo Amplifier
USB devices
such as
USB camera or
USB cable
USB port
(Type-A)
Computer (USB)*
USB port (Type-B)
1
USB memory
Devices that
require power
supply:
Ex:
MultiPresenter
Stick
USB storage device
AV Amplifier
DVD Player
(HDMI)
DVD Player or
Computer
Dotted lines = other signal Solid lines = video signal Dashed lines = audio signal
*: Multiple monitors that are daisy-chained have a limit to the connectable monitors. *1: The device connected to USB2 can control the device connected to USB1.
DVD Player (HDMI) or
Computer (HDMI)
DVD Player
(HDMI)
Computer (DisplayPort)
Computer (DisplayPort)
Second monitor*
Computer
DVD Player Stereo Amplifier
AV
Amplifier
VCR player or DVD player
English-16

Connecting to a Personal Computer

The type of video connections that can be used to connect to a computer depends on the computer’s display adapter. The following table show the typical factory preset signal timing for each connection type. Some display cards may not be able to support the required resolution for proper image reproduction with the selected connection. The monitor will show the proper image by automatically adjusting the factory preset timing signal.
<Typical factory preset signal timing>
Resolution
640 x 480 31.5 kHz 60 Hz Yes Yes Yes Yes 800 x 600 37.9 kHz 60 Hz Yes Yes Yes Yes
1024 x 768 48.4 kHz 60 Hz Yes Yes Yes Yes 1280 x 720 45.0 kHz 60 Hz Yes Yes Yes Yes 1280 x 768 47.8 kHz 60 Hz No No Yes Yes 1280 x 800 49.7 kHz 60 Hz Yes Yes Yes Yes
1280 x 1024 64 kHz 60 Hz Yes Yes Yes Yes
1360 x 768 47.7 kHz 60 Hz No No Yes Yes 1366 x 768 47.7 kHz 60 Hz No No Yes Yes
1400 x 1050 65.3 kHz 60 Hz Yes Yes Yes Yes
1440 x 900 55.9 kHz 60 Hz Yes Yes Yes Yes 1600 x 1200 75.0 kHz 60 Hz Yes Yes Yes Yes 1680 x 1050 65.3 kHz 60 Hz Yes Yes Yes Yes 1920 x 1080 67.5 kHz 60 Hz Yes Yes Yes Yes 1920 x 1200 74.6 kHz 60 Hz Yes Yes Yes Yes 1920 x 2160 133.3 kHz 60 Hz Yes Yes Yes Yes 3840 x 2160 65.7 kHz 30 Hz No No Yes* 3840 x 2160 67.5 kHz 30 Hz Yes* 3840 x 2160 133.3 kHz 60 Hz No Yes No Yes* 3840 x 2160 135.0 kHz 60 Hz No Yes*
4096 x 2160* 4096 x 2160*3135.0 kHz 60 Hz No Yes No No
*1: Recommended resolution. *2: Only HBR2 is set. *3: Compressed image.
Scanning frequency HDMI DisplayPort
Horizontal Vertical MODE1 MODE2 1.1a 1.2
1
Yes No No
1
3
54.0 kHz 24 Hz Yes Yes No No
No No
1
Yes
1, *2
English

Connecting to a Player or Computer with HDMI

• PleaseuseanHDMIcablewiththeHDMIlogo.
• Itmaytakeamomentforthesignaltoappearafterturningonthecomputer.
• Somedisplaycardsordriversmaynotdisplayanimagecorrectly.
• WhenyouuseacomputerwithHDMI,pleaseset[OVERSCAN]to[AUTO]or[OFF]asdisplaydriversmaynotbefully
compatible and may not display an image correctly (see page 33).
• To output HDMI audio, set [HDMI1], [HDMI2] or [HDMI3] at [AUDIO INPUT] in the OSD or choose [HDMI1], [HDMI2] or [HDMI3] by pressing the remote control AUDIO INPUT button.
• If the source signal is 3840 x 2160 (60 Hz) and 4096 x 2160 (60 Hz), please set [MODE2] at [HDMI] in [TERMINAL SETTINGS] (See page 37).
• If the monitor’s main power is turned on after a connected computer is turned on, sometimes an image is not displayed. In this case, please turn off the computer then turn it on again.

Connecting to a Computer with DisplayPort

• PleaseuseaDisplayPortcablewiththeDisplayPortcompliancelogo.
• To use the DisplayPort out connector, please refer to Video out (See page 67).
• Itmaytakeamomentforthesignaltoappearafterturningonthecomputer.
• WhenconnectingaDisplayPortcabletoacomponentwithasignalconversionadapter,animagemaynotappear.
• SomeDisplayPortcablesfeaturealockingfunction.Whenremovingthiscable,holddownthetopbuttontoreleasethelock.
• To output DisplayPort audio, set [DisplayPort1] or [DisplayPort2] at [AUDIO INPUT] in the OSD or choose [DisplayPort1] or
[DisplayPort2] by the remote control AUDIO INPUT button.
• To display individual images at each connected monitors with the DisplayPort OUT connector, please set [DisplayPort1.2] and [MST] at [DisplayPort] in the [TERMINAL SETTINGS] (See page 37).
• If the monitor’s main power is turned on after a connected computer is turned on, sometimes an image is not displayed. In this case, please turn off the computer then turn it on again.
English-17

Connecting a USB device

USB1: USB downstream port (Type-A). Connect a USB compatible flash memory or keyboard to Down Stream Port.
USB2: USB upstream port (Type-B). Connect to a USB compatible computer with a USB cable. A USB compatible computer connected to USB2 can control the devices connected to USB1.
USB CM1 (2A): Power supply port. Please refer to the specifications page for power supply information (see page 71).
USB CM2: Service port. Please do not connect devices.
USB MP: USB downstream port (Type-A). To use the Media Player function, please use this port.
• Pleasemakesuretheconnectorshapeandorientationis correctly aligned when connecting the USB device or cable.
• DependingontheuseofcomputerBIOS,OSordevice,theUSBfunctionmaynotbeworking.Inthiscase,pleasecheck
user’s manual of your computer or device, or contact your supplier for detailed information.
• BeforeturningoffthemainpowerswitchofthemonitororshuttingdownWindows®, please turn off the USB function and
remove the USB cable from the monitor. You may lose data when the computer crashes.
• ItmaytakeafewsecondsuntilthemonitorrecognizestheUSBinput.DonotdisconnecttheUSBcableordisconnect and reconnect the USB cable before the monitor recognizes the input.
• You can set power supply for USB CM1 (2A) at [USB POWER] in the OSD menu (see page 43).
• When you use the USB CM1 (2A) port for power supply, please use a USB cable that supports 2A.
• Please refer to the [USB] in the OSD menu (See page 43) for the USB setting.
NOTE: USB CM1 (2A) and USB CM2 are not corresponding port.
Please refer to the connection (See page 16) to connect USB devices to the monitor.
CAUTION: Do not bind the USB cable. It may trap heat and start a fire.
English-18

Basic Operation

Power ON and OFF Modes

Press the power button on the Control Panel or Remote Control to turn on the monitor. NOTE: The Main Power switch must be in the ON position in order to power up the monitor using the remote control or the
button on the Control Panel.
OFF
Main Power Switch
ON
English
Button
Using the remote control
POWER ON button
English-19

Power Indicator

LED indicator
status and
lighting pattern
Glowing blue Normal Blinking green*1Under any of the conditions
below, no input signal has been detected by the monitor during the period of time you set:
• The monitor is using an
• [INPUT DETECT] is set to a
• [USB POWER] is set to [ON].
• [DisplayPort] in the
Glowing amber No AV signal input has been
detected by the monitor during the period of time you set. (with network signal input)
Blinking amber No AV signal input has been
detected by the monitor during the period of time you set. (no network signal input)
Glowing red Turn off the monitor by the
remote control or the monitor button.
*1: Time setting for [AUTO POWER SAVE] is available at [POWER SAVE] (See page 40).
Condition Recovery
Option Board.
setting except for [NONE].
[TERMINAL SETTINGS] is set to [MST].
1. Turn on the monitor by the remote control or the monitor button.
2. Send an AV signal input to the monitor.
Turn on the monitor by the remote control or the monitor button.
NOTE: If the indicator is blinking red in a combination
of long and short, a certain failure might have occurred, please contact your supplier.

Using Power Management

This monitor follows the VESA approved DPM (Display Power Management) function. The power management function is an energy saving function that automatically reduces the power consumption of the monitor when the keyboard or the mouse has not been used for a fixed period. This allows your monitor to enter a Power Management mode if the monitor’s [POWER SAVE] function is set to [ENABLE], and a certain amount of time has passed since the monitor recognized “no signal input”. It will increase the life and decrease the power consumption of the monitor.
NOTE: Depending on the computer and display card
used, this function may not operate. After the video signal was lost, the monitor automatically goes into OFF at a preset time period.

Aspect

For [MP] (Media Player)
FULL ZOOM NORMAL
For [DisplayPort1], [DisplayPort2], [OPTION]*
FULL 1:1 ZOOM NORMAL
For [HDMI1], [HDMI2], [HDMI3]
FULL WIDE DYNAMIC 1:1 ZOOM NORMAL
*1: This function depends on which Option Board you are using.
Aspect ratio
of image
Unchanged view*
3
NORMAL
4:3
DYNAMIC
FULL
Squeeze
WIDE
Letterbox
*3 Grey areas indicate unused portions of the screen.
NORMAL: Reproduces the aspect ratio that is sent from the source.
FULL: Fills the entire screen. WIDE: Expands a 16:9 letterbox signal to fill the entire
screen. DYNAMIC: Expands a 4:3 pictures to fill the entire screen
with non-linearity. Some of the outside image area will be cut off due to expansion.
1:1: Shows the image in a 1 by 1 pixel format.
ZOOM
The image can be expanded beyond the active screen area. The parts of the image outside the active screen area are not shown.
ZOOM
1
Recommended selection
for picture aspect*
3
English-20
ZOOM

Media Player

Plays saved data, such as still and motion images, BGM (Background Music), on a USB storage device or microSD memory card connected to the monitor.
Top screen of the viewer
• Select [SETTINGS] to change the media player settings.
• While [AUTO PLAY] has been set to [SLIDESHOW] in [SETTINGS], the monitor starts performing [AUTO PLAY] by the
operation below:
- When connecting a USB storage device to the USB MP (Terminal Panel page 10), with the monitor already powered ON and the Media Player top screen displayed.
-
When the input signal is changed to [MP], with a USB storage device already connected to the USB (2A) port of the monitor.
For starting [AUTO PLAY], the system will automatically search the folder which is set in the [AUTO PLAY] settings [FOLDER] field, in the USB storage device and then display found still images or movies. The images and movies will be displayed in the [Sorted] order.
NOTE: Only 1 USB storage device can be recognized by the viewer.
English
A window will appear when you press the control panel buttons while the Media Player is active. You can select to control either the OSD menu or the Media Player from the window that opens.
If Media Player contents are played while [TILE MATRIX] is active, the image play timing might have a gap within monitors. If a monitor is used in portrait position, please set [OSD ROTATION] to [PORTRAIT]. Image orientation is changed according to
what you set at [OSD ROTATION]. When [OSD ROTATION] is set to [PORTRAIT], please use the motion image, which is rotated anticlockwise by [90°].
Displayable/playable files
Still
Supported formats
File extension Supported
.jpg, .jpeg, .jpe Baseline, Progressive, RGB, CMYK .png
Motion image
Supported formats
File extension Video codec Audio codec
.mpg, .mpeg MPEG1, MPEG2 MPEG Audio Layer3 (Abbreviation: MP3) AAC-LC (Abbreviation: AAC), LPCM .wmv H.264, WMV MP3, WMV Standard, WMA 9/10 Professional .mp4 H.264 MP3, AAC .mov H.264 MP3, AAC .flv, .f4v H.264 MP3, AAC
Interlace, α channel
English-21
Loading...
+ 53 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use