NEC 1850X User Manual

MultiSync LCD1850X

User’s Manual

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN
EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE
COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK • DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

CAUTION

Caution:

When operating the MultiSync LCD1850X (LH-18S02-1 and LH-18S02-BK1) with a
220-240V AC power source in Europe, use the power cord provided with the monitor.

In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse
installed for use with this equipment. If a power cord is not supplied with this equipment
please contact your supplier.

When operating the MultiSync LCD1850X with a 220-240V AC power source in
Australia, use the power cord provided with the monitor.

For all other cases, use a power cord that matches the AC voltage of the power outlet
and has been approved by and complies with the safety standard of your particular
country.

(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have
sufficient magnitude to cause electric shock. Therefore, it is dangerous to make
any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation
and maintenance of this unit has been included. Therefore, it should be read
carefully in order to avoid any problems.

English

ENERGYSTAR is a U.S. trademark.
As an ENERGYSTAR® Partner, NEC-Mitsubishi Electronics Display of America, Inc. has

determined that this product meets the ENERGYSTAR guidelines for energy efficiency. The
ENERGYSTAR emblem does not represent EPA endorsement of any product or service.

IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A and XGA are registered trademarks of
International Business Machines Corporation.

Apple and Macintosh are registered trademarks of Apple Computer Inc.

Microsoft and Windows are registered trademarks of the Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

All other trademarks or registered trademarks are property of their respective owners.

English-1

Declaration

Declaration of the Manufacturer

We hereby certify that the colour monitor

MultiSync LCD1850X (LH-18S02-1)
MultiSync LCD1850X (LH-18S02-BK1)

is in compliance with

Council Directive 73/23/EEC:

Council Directive 89/336/EEC:

and marked with

– EN 60950

– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024

NEC-Mitsubishi Electric Visual Systems, Corp.

MS Shibaura Bldg., 13-23,

Shibaura 4-chome,

Minato-Ku, Tokyo 108-0023, Japan

Power consumption of the monitor is less
than 3 W when in power-saving mode.

English-2

For the Customer to use in U.S.A. or Canada

Canadian Department of Communications
Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouiller du Canada.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety
Regulations according to CSA C22.2 #950.
Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de
sûrele Canadiens selon CAN/CSA C22.2 No. 950.

FCC Information

1. Use the attached specified cables with the MultiSync LCD1850X
colour monitor so as not to interfere with radio and television
reception.

(1)The power supply cord you use must have been approved by and

comply with the safety standards of U.S.A., and meet the following
condition.

Power supply cord Non shield type, 3-conductor

Length 1.8 m

Plug shape

English

(2)Shielded video signal cable. Use of other cables and adapters

may cause interference with radio and television reception.

English-3

2. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced
radio/television technician for additional suggestions. The user may
find the following booklet, prepared by the Federal Communications
Commission, helpful: “How to Identify and Resolve Radio-TV
Interference Problems.” This booklet is available from the U.S.
Government Printing Office, Washington, D.C., 20402,
Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions. (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

U.S. Responsible party: NEC-Mitsubishi Electronics

Display of America, Inc.

Address: 1250 N. Arlington Heights Road

Itasca, Illinois 60143-1248

Tel. No.: [phone]

Type of Product: Computer Monitor

Equipment Classification: Class B Peripheral

Models: MultiSync LCD1850X

We hereby declare that the equipment specified above conforms to the technical

standards as specified in the FCC Rules.

English-4

Contents

Your new NEC MultiSync LCD monitor box* should contain the following:

• MultiSync LCD1850X

• Power Cords

• Video Signal Cable (15-pin mini D-SUB male to DVI-A)

• Video Signal Cable (DVI-D to DVI-D Cable)

• User’s Manual

• NEC LCD Setup Software, Pivot Software, User’s Manual and other

helpful files. To see the User‘s Manual, Acrobat Reader 4.0 must be
installed on your PC.

monitor with tilt base

English

* Remember to save your original box and packing material to transport

or ship the monitor.

English-5

Quick Start

To attach the MultiSync LCD monitor to your system, follow these
instructions:

1. Turn off the power to your computer.

2. For the PC or Mac with DVI digital output: Connect the DVI-D to
DVI-D signal cable to the connector of the display card in your
system (Figure A.1). Tighten all screws.

For the PC with Analog output: Connect the 15-pin mini D-SUB to
DVI-A signal cable to the connector of the display card in your system
(Figure A.2).

For the Mac: Connect the MultiSync Macintosh cable adapter to the
computer (Figure B.1). Attach the 15-pin mini D-SUB signal cable to
the MultiSync Macintosh cable adapter (Figure B.1).

NOTE: Some Macintosh systems do not require a Macintosh cable

adapter.

3. Remove connector cover. Connect the DVI signal cable to the
connector on the back of the monitor. Place the video signal cable
(Figure C.1).

Replace connector cover.

NOTE: Incorrect cable connections may result in irregular operation,

damage display quality/components of LCD module and/or
shorten the module’s life.

4. Connect one end of the power cord to the AC inlet on the back of the
monitor and the other end to the power outlet (Figure D.1).

NOTE: Please refer to Caution section of this manual for proper

selection of AC power cord.

5. Check the Vacation Switch on the right hand side of the monitor is in
the ON position. Turn on the monitor with the Power Button
(Figure E.1) and the computer.

NOTE: There are two switches: one on the right side and one on the

front side of the monitor. DO NOT switch on/off quickly.

English-6

6. To complete the setup of your MultiSync LCD monitor, use the
following OSM controls:

• Auto Adjust Contrast (Analog input only)

• Auto Adjust (Analog input only)

Refer to the Controls section of this User’s Manual for a full description
of these OSM controls.

NOTE: If you have any problems, please refer to the Troubleshooting

section of this User’s Manual.

NOTE: Refer to User’s Manual in the NEC LCD Setup Software CD

case for installation and operation of this software.

English

Figure A.1

Macintosh Cable
Adapter (not included)

Figure A.2

Macintosh G3 and G4 do not
need a Macintosh cable adapter

Figure B.1

English-7

Input1 Input2

Figure D.1

Figure C.1

Power Button

Figure E.1

English-8

Vacation Switch

Raise and Lower Monitor Screen

The monitor may be raised or lowered in either Portrait or
Landscape mode.

To raise or lower screen, place hands on each side of the monitor and
lift or lower to the desired height (Figure RL.1).

Screen Rotation

Before rotating, the screen must be raised to the highest level to avoid
knocking the screen on the desk or pinching your fingers.

To raise the screen, place hands on each side of the monitor and lift up
to the highest position (Figure RL.1).

To rotate screen, place hands on each side of the monitor screen and
turn clockwise from Landscape to Portrait or counter-clockwise from
Portrait to Landscape (Figure R.1).

To toggle the orientation of the OSM menu between Landscape and
Portrait modes, press the RESET button while OSM menu is off.

Tilt and Swivel

Grasp both sides of the monitor screen with your hands and adjust the
tilt and swivel as desired (Figure TS.1).

Remove Monitor Stand for Mounting

English

To prepare the monitor for alternate mounting purposes:

1. Disconnect all cables.

2. Place hands on each side of the monitor and lift up to the
highest position (Figure RL.1).

3. Place monitor face down on a non-abrasive surface (Place the
screen on a 50 mm platform so that the stand is parallel with the
surface.) (Figure S.1).

4. Press the “
same time slide the lower stand cover. (Figure S.2)

Next, lift up the stand, remove the lower stand cover, then go on to
remove the upper stand cover. (Figure S.3)

Return the stand to its original position, remove the 4 screws that
connect the monitor to the stand, and lift off the stand assembly.
(Figure S.4)

” portion with your index finger and at the

English-9

5. Reverse this process to reattach stand.

NOTE: Use only VESA-compatible alternative mounting method.

Figure RL.1

Figure R.1

Figure TS.1

English-10