NCR 7772, CX7, 7772-1516-8801, 7772-1216-8801, 7772-1316-8801 User Manual

User Guide

NCR CX7 All-in-One POS (7772)

BCC5-0000-5363
Issue A

The product described in this document is a licensed product of NCR Corporation.

NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.

Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.

Email: [e-mail]

Copyright © 2019
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved

Preface

Audience

This book is written for hardware installer/service personnel, system integrators, and
field engineers.

Notice: This document is NCR proprietary information and is not to be disclosed or
reproduced without consent.

Safety Requirements

The NCR CX7 All-in-One POS (7772) conforms to all applicable legal requirements. To
view the compliance statements see the NCR RealPOS Terminals Safety and Regulatory

Statements (B005-0000-1589).

Caution: The on/off switch is a logic switch only. The AC line voltage primaries are live
at all times when the power cord is connected. Therefore, disconnect the AC power
cord before opening the unit to install features or service this terminal.

i

Lithium Battery Warning

Warning: Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type as recommended by the manufacturer. Discard used
batteries according to the manufacturer's instructions.

Attention: Il y a danger d'explosion s'il y a remplacement incorrect de la batterie.

Remplacer uniquement avec une batterie du même type ou d'un type recommandé
par le constructeur. Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.

Battery Disposal (Switzerland)

Refer to Annex 4.10 of SR814.013 for battery disposal.

IT Power System

This product is suitable for connection to an IT power system with a phase-to-phase
voltage not exceeding 240 V.

Peripheral Usage

This terminal should only be used with peripheral devices that are certified by the
appropriate safety agency for the country of installation (UL, CSA, TUV, VDE) or those
which are recommended by NCR Corporation.

Warning: DO NOT connect or disconnect the transaction printer while the terminal

is connected to AC power. This can result in system or printer damage.

Warning: DO NOT connect or disconnect any serial peripherals while the terminal

is connected to AC power. This can result in system or printer damage.

ii

Grounding Instructions

In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is
equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances. Do not
modify the plug provided – if it will not fit the outlet, have the proper outlet installed by
a qualified electrician. Improper connection of the equipment-grounding conductor can
result in a risk of electric shock.

The conductor with insulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor.

If repair or replacement of the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal. Check with a qualified electrician or
service personnel if the grounding instructions are not completely understood, or if you
are in doubt as to whether the product is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole
receptacles that accept the product’s plug. Repair or replace damaged or worn cords

immediately.

Out of Box Failure (OBF)

If you experience an out of box failure (OBF) during installation or staging related to a
missing, wrong or defective unit or item, simply provide NCR with a detailed
description of the issue and the item will be replaced free of charge. For assistance with
this process send an email to [e-mail] with the following details:

• NCR Sales Order # (Sales Order # are located on the box)

• Date of Product Installation

• Product Model #

• Unit Serial #

• NCR part # of defective/missing/wrong component

• Description of Failure (please be specific. For example: “display will not power on”)

• Customer/Requestor’s contact name, phone number and/or e-mail address

• Address to ship replacement part(s)

iii

Warranty

Transport the product in its original packaging to prevent impact damages.

If you do not have access to a computer, you may leave a voice message at: 1-800-528­8658 (USA), or (International) [phone]. When leaving a message, please provide a
phone number and/or an email address so NCR can contact you if additional details are
needed.

Note: Used equipment that experiences a failure does not qualify as an OBF and should
go through the NCR warranty process.

Warranty terms vary by region and country.

All parts of this product that are subject to normal wear and tear are not included in the
warranty. In general, damages due to the following are not covered by the warranty.

• Improper or insufficient maintenance

• Improper use or unauthorized modifications of the product.

• Inadequate location or surroundings. Site installation must conform to guidelines
listed in the NCR CX7 All-in-One POS (7772) Site Preparation Guide (BCC5-0000-5364)
and the NCR Workstation and Peripheral AC Wiring Guide (BST0-2115-53).

For detailed warranty arrangements please consult your contract documents.

iv

Returning Defective Hardware for Service

Use the following procedure to report/return defective hardware.

Call the NCR Customer Care Center at 1-800-262-7782 and have the following information
available when you place the call.

• Class/Model number of the defective equipment

• Serial Number of the defective equipment

• Equipment location in the store

• Description of the problem, including any system error codes, error condition, or
guidance to the area of failure.

The NCR Agent will provide you with a work order number, which serves as your
Return Material Authorization (RMA). Please provide the RMA on the outside of the
shipping box.

Note: A work order must be opened for each device that is shipped for repair.

Table of Contents

Chapter 1: Product Overview

Base Models 2

Features 3

Optional Features 4

Operating Systems 5

Specifications 6

Mounting Configurations 9

Base with Remote Power Supply (F033/F035) 9

v

Base with Integrated Power Supply 9

Operator Controls 10

Power Switch 10

Recovery Tool Button 10

LEDIndicators 11

Power Status LED 11

I/O Panel LED 12

Label Locations 13

CX7 with Base 13

Chapter 2: Hardware Installation

Installation Restrictions 15

Ergonomic Workplace 15

I/O Ports 16

Retail I/O 16

Hospitality I/O 17

I/OBoard Connector Pinouts 18

12V USB +Power 18

24V USB +Power 19

Cash Drawer 20

vi

DisplayPort 22

LAN 23

PowerIn 23

USB-C 24

USB 3.0 24

DB-9 Serial 25

RJ12 Serial 25

RJ45 Serial 26

RJ50 Serial 27

Installing the Terminal 28

Connecting ACPower 29

Connecting to a Network 29

Installing the Cash Drawer 30

Installing the Second Cash Drawer 31

Second Cash Drawer for Retail I/O 31

Second Cash Drawer for Hospitality I/O 32

Installing the Transaction Printer 34

Powering Up the Terminal 35

Chapter 3: Operation and Cleaning

Touchscreens 36

Projected Capacitive Touchscreen 36

Using the PCap Touchscreen 36

Cleaning the Touchscreen 36

Magnetic Stripe Reader 37

Using the MSR 37

Care of Cards 37

Card Thickness 37

Biometrics Fingerprint Reader 38

Using the Biometrics Reader 38

Cleaning the Sensor 39

Software Drivers 39

Cleaning the Cabinet 40

Cleaning the Cooling Vents 41

Chapter 4: Disk Image Backup and Recovery Tool

Introduction 42

Running the Recovery Tool 43

Starting the Recovery Tool 43

Main Screen 44

Save or Load Image 45

Saving an Image 46

Loading An Image 50

Change Settings 54

Change Network Settings 55

vii

Change Password 56

Replace Recovery Image 57

Change Language 58

Creating a Disk Image 59

Chapter 5: Configuring a Second SSD for RAID

Introduction 60

Configuring a RAID System 61

Chapter 6: Power Management

Computer States 66

G3 Mechanical Off 66

G2/S5 Soft Off 66

G1 Sleeping 66

G0 Working 67

ACPI Sleep States (S0 - S5) 67

Enabling Wake on LAN 70

Chapter 7: BIOS Setup

Entering Setup 73

Selecting Menu Options 73

viii

Restoring Factory Settings 73

BIOS Default Settings 74

Advanced Menu 74

Chipset Menu 75

Security Menu 76

Boot Menu 76

Chapter 8: BIOS Updating Procedure

Introduction 77

Prerequisites 77

USB Flash Key update prerequisites 77

Windows Flash Executable update prerequisites 77

SPI/BIOS Updating Procedures 78

Using the Bootable USB Flash Key 78

Using the Windows Flash Executable 82

Chapter 9: Initial Terminal Imaging

Introduction 83

Imaging Procedure 83

Revision Record

Issue Date Remarks

ix

A

Jul 2019 First Issue

x

Chapter 1: Product Overview

The NCR CX7 All-in-One POS (7772), powered by Intel’s 8th Generation Coffee Lake
chipset, features a sleek design, packed with superior performance. The new, stylish
design provides a wide range of configuration versatility. The ability to configure with
an I/O board that accommodates environments with more USB devices or an I/O board
that accommodates environments with more serial devices gives customers the
flexibility that prevents additional expansion boards or hubs.

The CX7 offers two I/O configurations for the base:

• Retail I/O Base

• Hospitality I/O Base

I/O Board Connectors Retail I/O Hospitality I/O

USB-C to Head 1 1

12VPowered USB 3 1

24VPowered USB 1 1

Serial 1 x RJ50

1 x DB9

4 x RJ12
2 x RJ45

USB3.0 (5V) 2 2

DisplayPort 1 1

Cash Drawer (12/24 V) 1 (dual port) 2

1-2 Product Overview

I/O Board Connectors Retail I/O Hospitality I/O

LAN 1 1

Both I/O boards are connected to the CX7 core motherboard through a single USB Type­C connector. In addition to the integration of the board in the base, each I/O can be
configured for a wall mount solution, pole mount solution, or ordered in a remote
chassis to permit placement under the counter.

Base Models

Model Description

7772-1216-8801 15.6" PCAP RGB w/ Intel Celeron, 8GB DDR4 memory, No

HDD, No Power Supply

7772-1316-8801 15.6" PCAP RGB w/ Intel i3, 8GB DDR4 memory, No HDD,

No Power Supply

7772-1516-8801 15.6" PCAP RGB w/ Intel i5, 8GB DDR4 memory, No HDD,

No Power Supply

Product Overview 1-3

Features

Feature Description

Memory F134 8GB, DDR4 2400MHz (Add On)

F136 16GB, DDR4 2400MHz (Add On)

Storage Media F241 SSD 120 GB, M.2 SATA

F242 DUAL SSD 120 GB, M.2 SATA

F253 SSD 240 GB, M.2 NVMe (PCIe)

F255 SSD 480 GB, M.2 NVMe (PCIe)

Port A(Right Side) Features F140 No Peripheral Filler Plate

F141 NCR Encrypted MSR

Port B(Left Side)Features F150 No Peripheral Filler Plate

F151 Biometrics

Port C (Bottom/ Chin)Features F160 No Peripheral Filler Plate

F165 Wireless Card and Antenna

Port DFeatures F450 No Customer Display - Logo Badge

F452 7" Non-Touch LCD (XL7) Customer Display

F453 7" Touch LCD (XL7) Customer Display

Base Display F457 No Base Display Option

Base and Power Supply F033 Base for Retail I/O, Remote Power Supply

F035 Base for Hospitality I/O, Remote Power

Supply

Power Cord F100 US Power Cord

F101 International Power Cord

F102 UK Power Cord

F103 Australia Power Cord

F104 China Power Cord

F105 SEV Power Cord

F106 India Power Cord

F108 Argentina Power Cord

F109 Power Cord 120V Twist Lock

F119 No Power Cord

1-4 Product Overview

Optional Features

Optional Feature Description

Ethernet Cable F110 7772 10/100/1000 Ethernet Cable

Product Overview 1-5

Operating Systems

The OS image and base platform drivers will be pre-loaded on the solid state drive prior
to shipment. The POS must be configured with a solid state drive.

Product ID Product ID Description

7772-F700 No Operating System Approval

7772-F720 Windows 10 IoT Enterprise 2019 LTSC Value 64 bit

(UEFI) Embedded Operating System

7772-F740 Orderman Windows 10 IoT Enterprise 2019 LTSC

Value 64 bit (UEFI) Embedded Operating System

7772-F790 SUSE Linux Enterprise Server (SLES) 15 64 bit

Operating System

Base client and third-party software are also available on the public NCR Platform
Software Website: http://www.ncr.com/support/support_drivers_

patches.asp?Class=External\display

Configuration
Notes

required

Pre-installed in
the factory

Pre-installed in
the factory

Pre-installed in
the factory

1-6 Product Overview

Specifications

Model Specs Good Better Best

Chipset Intel Q370 “Coffee Lake”

Processor Intel® Celeron®

G4900T

Clock Speed 2.9GHz 3.1GHz 2.1GHz

Turbo Boost for Peak
Loads

Level 2 Cache 2MB 4MB 6MB

Thermal Design
Power

AMT No Yes Yes

Intel vPro No No Yes

Image Recovery
Button

Odometer Chip Yes Yes Yes

RAID Support Yes Yes Yes

TPM Yes Yes Yes

N/A N/A Up to 3.5 GHz

35 Watts 35 Watts 35 Watts

Yes Yes Yes

Intel® Core™ i3­8100T

Intel® Core™ i5­8500T

Memory

Memory Type DDR4-2133MT DDR4-2133MT DDR4-2133MT

Form Factor SODIMM SODIMM SODIMM

Memory Slots 2 2 2

Standard Memory 8GB (1 x 8GB) 8GB (1 x 8GB) 8GB (1 x 8GB)

Maximum Memory 32GB (2 x 16GB) 32GB (2 x 16GB) 32GB (2 x 16GB)

Storage

SSD - Solid State Drive
(M.2 SATA)

SSD - Solid State Drive
(M.2 NVMe)

SSD - Solid State Drive
(M.2 NVMe)

120GB SSD 120GB SSD 120GB SSD

240GB SSD 240GB SSD 240GB SSD

480GB SSD 480GB SSD 480GB SSD

Product Overview 1-7

Model Specs Good Better Best

Dual Solid State Drive

Dual 120GB SSD Dual 120GB SSD Dual 120GB SSD

(M.2 SATA)

Integrated Touch Display

15.6” Projected

Yes Yes Yes

Capacitive
1366 x 768
10-point touch

Brightness 400 nits 400 nits 400 nits

Screen Life 50K Hours to half

brightness

50K Hours to half
brightness

50K Hours to half
brightness

Integrated Speaker Standard Standard Standard

Peripherals

3-track Encrypted

Option Option Option

MSR

Integrated Wireless

Option Option Option

802.11 AC & Bluetooth

Integrated Biometric

Option Option Option

Reader

Imager Option Option Option

2-in-1 Sign-in Device Option Option Option

Consumer Displays

APA customer display Option Option Option

7” Color LCD

Option Option Option

(Touch or Non-touch)

10” Color LCD

Option Option Option

(Touch or Non-touch)

Dimensions/Weight

CX7 terminal with
base

• Dimensions (w x d x h)

14.95” x 7.81” x 12.08”
(379.7 mm x 198.4 mm x 306.8 mm)

• Weight

11.35 lbs (5.15 kg)

1-8 Product Overview

Model Specs Good Better Best

CX7 terminal without
base

• Dimensions (w x d x h)
Width 14.95” x 1.26” x 9.32”
(379.7 mm x 32.0 mm x 236.6 mm)

• Weight

5.30 lbs (2.40 kg)

Product Overview 1-9

Mounting Configurations

Base with Remote Power Supply (F033/F035)

• with Retail I/O (F033)

• with Hospitality I/O (F035)

Base with Integrated Power Supply

7772-K032 provides an option to permit integration of the power supply in the base.

1-10 Product Overview

Operator Controls

Power Switch

The Power Switch is located on the bottom of the display. This switch is a momentary
contact, push-on-push-off switch.

Recovery Tool Button

The Recovery Tool Button is for the OS Recovery Tool option. The recessed button is
located on the bottom of the display. The button is a momentary contact, push-on-push­off switch.

Product Overview 1-11

LEDIndicators

Power Status LED

The Power Status LED, located on the front of the display, has multiple functions as
defined below.

Color Description

Solid Green Terminal is ON and all voltages from power supply and

motherboard are okay.

Blinking Green Terminal is in SUSPEND (S3/S4)mode.

Solid Red Processor over temperature.

1-12 Product Overview

I/O Panel LED

The Status LED is located on the I/O Panel on the Base.

Color Description

Green

Orange

Off

On

S3

Off

Product Overview 1-13

Label Locations

CX7 with Base

1-14

Chapter 2: Hardware Installation

Installation Restrictions

• The NCR CX7 All-in-One POS (7772) conforms to all applicable legal requirements.
To view the compliance statements see the NCR RealPOS Terminals Safety and

Regulatory Statements (B005-0000-1589).

• Install the CX7 near an electrical outlet that is easily accessible. Use the power cord
as a power disconnect device.

• Do not permit any object to rest on the power cord. Do not locate the CX7 where
the power cord can be walked on.

• Use a grounding strap or touch a grounded metal object to discharge any static
electricity from your body before servicing the CX7 terminal.

Warning: This unit contains hazardous voltages and should only be serviced by

qualified service personnel.

Caution: Do not connect or disconnect the transaction printer while the terminal is on.

This can result in system or printer damage.

Ergonomic Workplace

The NCR CX7 All-in-One POS (7772) has a high–brightness LCD with an anti–glare
screen. For best results, please observe the following when considering the terminal
workplace:

• Avoid direct–glaring and reflective–glaring light. Locate the terminal in a controlled
luminance surrounding. When installed next to windows position the terminal so it
does not reflect the outside light.

• If possible, avoid reflective glaring caused by electric light sources.

• Position the terminal for ideal viewing angles.

2-16 Hardware Installation

I/O Ports

Retail I/O

The following are the default I/O ports for the NCR CX7 All-in-One POS (7772) with a
Retail I/OBase.

Callout Port Name

1 Cash Drawer

2 USB24V

3 USB12V

4 24V Power In

5 LED

6 USB-C

7 LANOut

8 LANIn

9 DB9 Serial

10 DisplayPort

11 Dual USB 3.0

12 RJ50 Serial

Hardware Installation 2-17

Hospitality I/O

The following are the default I/O ports for the NCR CX7 All-in-One POS (7772) with a
Hospitality I/OBase.

Callout Port Name

1

2

3

4

5

6

7

8

9

10 DisplayPort

11 Cash Drawer

12 RJ12 Serial

RJ45 Serial

Dual USB 3.0

USB12V

USB24V

24VPower In

LED

USB-C

LANOut

LAN In