Assembly Instructions - Please keep for future reference
Cat No.
RE446
Kempton Coffee Set Brown
No. People Assembly Time
30 - 60
Minutes
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the JDW customer helpline: 0871 231 2000
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools
listed on the next pages.
• Remove all ttings from the
plastic bags and seperate
them into their groups.
• Keep children and animals
away from the work area,
small parts could choke if
swallowed.
Care and Maintenance
• Please clean using cloth
with glass cleaner, do not
use bleach or abrasive
cleaners.
• Make sure you have
enough space to lay out
the parts before starting.
• Do not stand or put weight
on the product, this could
cause damage.
• Assemble the item as close
to its nal position (in the
same room) as possible.
• Assemble on a soft, level
surface to avoid damaging
the unit or your oor.
• From time to time check
that there are no loose
screws on this unit.
• We do not recommend the
use of power
drills/drivers
for inserting
screws as this
could damage
the unit. Only use hand
screwdrivers.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Warning
Important - In order to help prevent overturning, this product must be used with the wall anti-tip
strap/device provided.
• To help prevent product toppling over please follow the below steps:
• Use the anti-tip strap/device provided.
• Do not allow children to climp or hang on the furniture.
• Do not place heavy items on top of the furniture, unless the furniture has been designated for
this purpose.
Please note that only the anti-tip strap/devices and screw are provided, you will need to provide
wall plugs and screws applicable for your wall type.
If you need help or have damaged or missing parts, call the JDW
customer helpline: 0871 231 2000
If you are unhappy with the product and wish to return it,
please follow the retailer’s returns procedure.
Exploded View
D
J1
G
P
J2
I
H
B
K
A
J1
Q
C
A
B
J2
F
E
Components - Panels
Please check that you have all the components listed below before constructing your item.
Part No Description Qty
A 2
B
C 1
D 2
E 2
F 2
G 1
H 1
I 1
J1 3
J2 3
2
K 1
P 1
Q 2
Components - Fixings
Please check that you have all the components listed below before constructing your item.
L M6x25mm 20
M
N M6 32
O M6x15mm 16
R 1
Tools Required
Allan Key
M6x30mm
12
Ruler - Use this to measure your screws (mm)
Assembly Instructions
Note: All Bolt Head Caps and Nut Caps should not be attached before finally
tightening all Bolts with the Allen Key.
Only tighten all bolts when you are satisfied with the alignment of all components.
Step 1
• Connect the table
A
B
leg part (Part A)
with the side part
(Part B), fasten
them by bolts
(Part L) and
washers (Part N).
L
Step 2
• Connect the other
table leg part
(Part A) with the
side part (Part B),
fasten them by
bolts (Part L) and
washers (Part N).
N
A
L
N
Step 3
• Connect another
table side part
(Part B) with the
B
leg part, fasten
them by bolts
Step 4
L
N
(Part L) and
washers (Part N).
• Add the adjusting
knob (Part O) to
the bottom of the
table leg. Put the
table top part
(Part C) into the
table middle
position.
C
O
Step 6
• Connect the chair
right armrest part
(Part J1) with the
chair back part
K
Step 5
• Put the table
glass (Part K) on
the table top.
(Part D) by insert.
Fasten them
together by bolts
(Part M) and
washers(Part N).
L
N
E
DM
J1
Step 7
• Fasten the chair
front part (Part E)
with the right
armrest part by
bolts (Part L) and
N
washers (Part N).
Step 8
• Connect the chair
left armrest part
(Part J2) with the
Step 9
• Put the chair seat
part (Part F) into
N
M
J2
L
N
chair back part
by insert and
bolts (Part M) and
washers (Part N).
•
Fasten the
armrest part with
the chiar front
part by bolts
(Part L) and
washers(Part N).
F
the chair seat and
add the adjusting
knob (Part O) to
the bottom of
the armrest.
O
Step 10
Q
• Put the chair seat
cushion (Part Q)
on the seat.
M
Step 11
• Connect the sofa
right armrest part
(Part J1) with the
sofa back part
(Part G) by insert.
Fasten them
N
Step 12
• Fasten the sofa
front part (Part H)
with the right
armrest part by
bolts (Part L) and
washers (Part N).
J1
L
together by bolts
(Part M) and
G
washers (Part N).
N
H
N
M
J2
Step 13
• Connect the sofa
left armrest part
(Part J2) with the
sofa back part by
insert and bolts
(Part M) and
washers (Part N).
Fasten the
L
N
•
armrest part with
the sofa front part
by bolts (Part L)
and washers
(Part N).
Step 14
•
Put the sofa seat
part (Part I) into
the sofa seat.
Add the adjusting
knob (Part O)
to the bottom
of the armrest.
Step 15
•
Put the sofa seat
I
O
cushion (Part P)
on the seat.
P
CARE AND CLEANING:
1. TO CLEAN,WIPE WITH DAMP CLOTH.DO NOT USE BLEACH,ACID SOLVENTS OR ABRASIVE CLEANERS
OR FRAME PARTS.
2. DURING VARYING WEATHER CONDITIONS AND WINTER PERIOD,WE STRONGLY RECOMMEND THAT
IT CAN BE.STORED IN A DRY AREA
WITH A SUITABLE COVER BEFORE STORAGE,PLS INSURE IT IS CLEAN AND DRY.
3
.
PERIODICALLY CHECK AND ENSURE THAT ALL THE SCREWS ARE COMPLETELY TIGHTEN.
4
.
A MATCHING FURNITURE COVER IS STRONGLY RECOMMENDED TO EXTEND THE USAGE LIFE-SPAN.
Manchester
M60 6ES
Loading...