N35WG
3/8” STICK ON, BREAKOFF END FLANGE, CENTER LEADS
DESCRIPTION
Nascom’s N35WG Series, 3/8” stick on contact, protects all nonferrous (e.g.
wood, aluminum and vinyl) doors and windows, in both residential and commercial settings.
The N135WG is the installer’s choice of contact conguration where excellent
air and side-to-side gap are required to prevent false alarms caused by shifting or warping doors and windows.
FEATURES
• BREAKOFF FLANGE • ENCAPSULATED HERMETICALLY SEALED CONTACTS
• 12” 22AWG WIRE LEADS • 3M VHB (Very High Bond) DOUBLE SIDED TAPE
• WIDE GAP - N35 NdFeB RARE EARTH MAGNET • ABS HOUSINGS
• LISTED TO UL634 STANDARD
ORDERING INFORMATION
PART
NUMBER
COLOR
CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N35WGSW/ST
N35WGB/ST
N35WGG/ST
N35WGT/ST
N35WGW/ST
SNOW WHITE
BROWN
GREY
TAN
WHITE
DUAL CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N35WGSW/ST2CR
N35WGB/ST2CR
N35WGG/ST2CR
N35WGT/ST2CR
N35WGW/ST2CR
SNOW WHITE
BROWN
GREY
TAN
WHITE
OPEN LOOP, NORMALLY CLOSED, 1FB, SWITCH/MAGNET SET:
N35WGSW/STFB
N35WGB/STFB
N35WGG/STFB
N35WGT/STFB
N35WGW/STFB
SNOW WHITE
BROWN
GREY
TAN
WHITE
SINGLE POLE DOUBLE THROW, SWITCH/MAGNET SET:
N35WGSW/STSD
N35WGB/STSD
N35WGG/STSD
N35WGT/STSD
N35WGW/STSD
SNOW WHITE
BROWN
GREY
TAN
WHITE
HIGH SECURITY, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:
N35WGSW/STHS
N35WGB/STHS
N35WGG/STHS
N35WGT/STHS
N35WGW/STHS
SNOW WHITE
BROWN
GREY
TAN
WHITE
OPERATE
GAP
(in inches)
0.75 to 1.125 200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms
0.75 to 1.125 200 VDC 0.5 Amps 10vA 1.5 Amps 150 mOhms
0.65 to 1.00
0.65 to 1.00
0.1875 to
0.5000
30 VDC 0.2 Amps 3vA 0.5 Amps 100 mOhms
30 VDC 0.2 Amps 3vA 0.5 Amps 100 mOhms
300 VDC
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
CONTACT RATING
(Max DC/Peak AC Resistive)
SWITCHING CARRY
V I V I
0.25
Amps
|
10vA
F: 800.727.4041
Amps
STATIC
CONTACT
RESISTANCE
(50mV, 100mA)
0.25
|
150 mOhms
initial
www.nascominc.com
DWG No. 131118-05 Rev. 1
1
.362
9.19
.118
3
2.140
54.36
.375
9.53
.100
2.54
1.754
44.55
R.075
1.91
TOP
VIEW
FRONT VIEW
.362
9.19
.118
3
2.140
54.36
.100
2.54
1.754
44.55
.375
9.53
R.075
1.91
FRONT VIEW
TOP
VIEW
WIRING SCHEMATIC
N35WG
3/8” STICK ON, BREAKOFF END FLANGE, CENTER LEADS
SWITCH
CONTACT
CLOSED LOOP,
NORMALLY OPEN CONTACT
DUAL CLOSED LOOP,
NORMALLY OPEN CONTACTS
DIMENSIONS - IN [mm]
SWITCH
CONTACT
OPEN LOOP,
NORMALLY CLOSED CONTACT
NC, OPEN LOOP (WHITE)
COMMON
(BROWN)
SPDT, SINGLE POLE DOUBLE THROW
NO, CLOSED LOOP (RED)
SWITCH
MAGNET
INSTALLATION INSTRUCTIONS
This switch and magnet set can be fastened using #4 round head wood screws or pan head sheet metal screws. The switch
and magnet housings feature a break away ange that can be removed if desired for tape mounting only. The installation
instructions refer to the more common mounting method using the supplied 3M VHB tape.
• Pre-t the switch and magnet in the desired location on the window. When mounting, be sure to allow enough clearance
between the switch and magnet for the snap on covers.
• Clean the mounting surface area for both switch and magnet with alcohol and let dry.
• Remove the liner from the tape on the back of the switch and carefully position the switch on the window frame as close
as possible to the movable part of the window.
• Remove the liner from the tape on the back of the magnet and carefully align the magnet parallel with the switch on the
movable part of the window.
• Apply rm pressure to the switch and magnet housing to ensure proper adhesion to the mounting surface.
• Test alarm system for correct operation.
• Snap the covers on the switch and magnet.
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 131118-05 Rev. 1
2
PART NUMBERING SYSTEM
N35WG
XX XX XXX/ XXXX XX XXX X XX
N35WG
3/8” STICK ON, BREAKOFF END FLANGE, CENTER LEADS
COLOR (1 or 2 digits):
• SW = SNOW WHITE
• B = BROWN
• G = GREY
• T = TAN
• W = WHITE
PRODUCT TYPE (1 or 2 digits):
• ST = SWITCH/MAGNET SET
• SW = SWITCH ONLY
• M = MAGNET ONLY
CIRCUIT (0 or 2 digits):
• Blank = CLOSED LOOP
• 2CR = DUAL CLOSED LOOP
• FB = OPEN LOOP
• SD = SPDT
• HS = HIGH SECURITY
•
LEAD LENGTH (zero, 3 or 4 digits):
• Blank - 12 Inches
• All other lengths specied in
Inches with 3 digits (e.g. 036 =
36 Inches)
END OF LINE RESISTOR (zero to 4 digits):
• Blank = Resistor in series with the switch
• P = Resistor in parallel with the switch
• SP = Resistor 1 in series to the switch; resistor
2 in parallel to the switch
BUILT-IN END OF LINE RESISTOR VALUE (zero to 4
digits):
• Blank = No built-in end of line resistor
• All other resistor values are specied (e.g. 1K
= 1,000 Ω)
LEAD WIRE COLOR (zero to 2 digits):
• Blank = Switch Color except:
» resistor contacts standard is red wire
» all 2 conductor jacketed wire is grey
• BL = Blue leads
• OL = Orange leads
WIRE TYPE (0 or 1 digit):
• Blank = UL1061 | 22AWG | 7/30
• Z = Zipcord ZIP NEC (UL) TYPE CL2
• J = 2-conductor PVC Jacketed NEC Type CL2
and CM
Royne Industries LLC, dba NASCOM
|
P: 800.843.5530
|
F: 800.727.4041
|
www.nascominc.com
DWG No. 131118-05 Rev. 1
3
Loading...