Napoleon Fireplaces WMFE1 User Manual [en, de, fr]

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

YOU MUST BE 18 YEARS OF AGE TO OPERATE THIS APPLIANCE.

OPERATING INSTRUCTIONS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ULC/ORD-C 627.1 / UL1370

WMFE1, WMFE2,

WMFE3 & WMFE4

INSTALLATION AND

ETHANOL DECORATIVE

APPLIANCE

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

SAFETY INFORMATION

WARNING

If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH, in Canada.

WMFE1

WARNING

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

WMFE2

WMFE3

$10.00

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁ replaces.com • ask@napoleonproducts.com

1.32A

W415-0958 / C / 03.01.12

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

3.0 LOCATING APPLIANCE 7

4.0 INSTALLATION 8

5.0 FINISHING 11

6.0 OPERATING INSTRUCTIONS 13

7.0 MAINTENANCE 16

8.0 REPLACEMENT PARTS 17

9.0 TROUBLESHOOTING 18

10.0 WARRANTY 19

11.0 SERVICE HISTORY 20

2.1 DIMENSIONS 5

2.1.1 WMFE1 (CORNER) 5

2.1.2 WMFE2 (SQUARE) 5

2.1.3 WMFE3 (LINEAR) 5

2.1.4 WMFE4 (CONVEX) 5

2.2 GENERAL INSTRUCTIONS 6

2.3 GENERAL INFORMATION 6

2.4 RATING PLATE INFORMATION 6

4.1 MINIMUM CLEARANCE TO COMBUSTIBLES 8

4.2 INSTALLING THE APPLIANCE 9

4.2.1 WMFE1 9

4.2.2 WMFE2, WMFE3 AND WMFE4 10

5.1 BURN POT / BURNER INSTALLATION 11

5.1.1 WMFE1 11

5.1.2 WMFE2, WMFE3 AND WMFE4 11

5.2 GLASS FENDER INSTALLATION 12

5.3 WARNING PLATE LOCATION 12

6.1 FILLING THE BURNER / BURN POT 13

6.1.1 WMFE1 13

6.1.2 WMFE2, WMFE3 AND WMFE4 14

6.2 IGNITION 15

6.3 EXTINGUISHING THE FLAME 15

6.3.1 WMFE1 15

6.3.2 WMFE2, WMFE3 AND WMFE4 16

7.1 CARE OF STAINLESS STEEL 16

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

W415-0958 / C / 03.01.12

1.0 INSTALLATION OVERVIEW

Mantel, see “MINIMUM CLEARANCE TO COMBUSTIBLES” section

Side Wall

Side Wall, see “MINIMUM CLEARANCE TO COMBUSTIBLES” section.

Glass Fender, see “GLASS FENDER INSTALLATION” section.

Rating plate, see “RATING PLATE INFORMATION” section.

W415-0958 / C / 03.01.12

2.0 INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED

• You must be 18 years of age to operate this appliance.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause ﬁ re or injury.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance, install an adjustable safety gate to keep toddlers, young chidlren and other at risk individuals out of the room and away from hot surfaces.

• Clothing and other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Insure that you have incorporated adequate safety measures to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Under no circumstances should the appliance be modiﬁ ed.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Insure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic components.

• Do not drink Ethanol.

• Do not operate while intoxicated.

• Always keep a ﬁ re extinguisher (type ABC) near the appliance.

• Do not smoke while ﬁ lling the appliance burn pot.

• Risk of Explosion

• Never use any fuel other than the fuels speciﬁ cally identiﬁ ed for use in the appliance. Never use gasoline.

• Never reﬁ ll appliance fuel reservoir when appliance is operating or still hot.

• Never use appliance in areas where ﬂ ammable vapours or gas may be present.

• Never store or transport the fuel in other than a metal or plastic container that is acceptable for use with the speciﬁ ed fuel in accordance with the Consumer Chemicals and Containers Regulations and is the original container for the speciﬁ ed fuel.

• Never store fuel in the same location as the appliance.

• Risk of Indoor Air Pollution - Use appliance only in well-ventilated areas and with doors of adjacent room open. People with breathing problems should consult a physician before using the appliance.

• Do not use appliance to heat or boil water or use as a cooking appliance.

• Do not use in a room with oxygen tanks in use.

• The appliance should not be used in a small room where less than 5.7 m3 (200ft3) of air space is provided for each 1000 Btu per hour. Do not use the appliance in a bathroom, a room where sleeping accommodation is provided or any other small room.

• The appliance should be inspected before use.

• The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapours and liquids other than those speciﬁ ed for use with this appliance.

• Keep an A, B, C ﬁ re extinguisher readily available when using this appliance.

WARNING

3.18A

W415-0958 / C / 03.01.12

2.1 DIMENSIONS

2.1.1 WMFE1 (CORNER)

/2”

26”

28 1/4”

2.1.2 WMFE2 (SQUARE)

23”

30 1/2”

2.1.3 WMFE3 (LINEAR)

1”

/16”

/2”

/8”

/4”

11 3/4”

2”

4 3/8”

18”

21”

/2”

/16”

/2”

/4”

2”

23”

2.1.4 WMFE4 (CONVEX)

28 5/16”

/16”

4 3/8”

34 5/16”

/16”

21”

/8”

/4”

/2”

/4”

/16”7 1/16”

W415-0958 / C / 03.01.12

2.2 GENERAL INSTRUCTIONS

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUA TE VENTILA TION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 36” FROM THE

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CON-

TACT WHEN THE APPLIANCE IS OPERATING.

USE ONLY WOLF STEEL APPROVED REPLACEMENT PARTS WITH THIS APPLIANCE. USING NON-

LISTED COMPONENTS COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY

2.3 GENERAL INFORMATION

NEVER USE ANY OTHER FUEL OTHER THAN THE FUELS SPECIFICALLY IDENTIFIED FOR USE IN

USE DENATURED ETHANOL (ETHYL ALCOHOL) FUEL ONLY.

NEVER USE GELLED ETHANOL FUELS. ONLY LIQUID FUELS ARE TO BE USED.

WARNING

FRONT FACE OF THE UNIT.

FIRE RISK. EXPLOSION HAZARD.

AND CERTIFICATION.

WARNING

THIS APPLIANCE.

4.9

RA TES AND EFFICIENCIES

WMFE1 WMFE2 WMFE3 WMFE4

MAX INPUT (BTU/hr 10,000 5,000 10,000 5,000 EFFICIENCY 99% 99% 99% 99% BURNER CAPACITY /litres 3 X 0.3 1.5 2 X 1.5 1.5 MAX BURN TIME(hr) 2 3 3 3

2.4 RATING PLATE INFORMATION

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

CERTIFIED UNDER / HOMOLOGUÉ SELON LES NORMES / ZERTIFIZIERT NACH : ULC/ORD-C627.1-2008, ULC 1370 UNVENTED ETHYL ALCOHOL FUEL BURNING DECORATIVE

APPLIANCES / APPAREILS DÉCORATIFS NON VENTILÉS, ALIMENTÉS À L'ALCOOL ÉTHYLIQUE / UNBELÜFTETES DEKORATIVES GERÄT ZUR VERBRENNUNG VON ETHYLALKOHOL

USE DENATURED ETHANOL FUEL ONLY.

WARNING: THIS APPLIANCE HAS NOT BEEN TESTED FOR USE WITH GLASS DOORS. TO REDUCE THE RISK OF FIRE OR INJURY, DO NOT INSTALL GLASS DOORS.

DO NOT USE AN APPLIANCE INSERT OR OTHER PRODUCTS NOT SPECIFIED FOR USE WITH THE PRODUCT. SEE INSTALLATION AND OPERATING INSTRUCTIONS FOR THIS MODEL.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS: WMFE 1 2,3,4

BACK 2” 1/2” BOTTOM 6” 2” SIDES 0” 12” CEILING / MANTEL 18” 18” FRONT 36” 36”

SERIAL NUMBER / NO. DE SÉRIE:

WMFE

CERTIFIED

CERTIFIED FOR / CERTIFIÉ POUR /

ZUGELASSEN FÜR

CANADA / USA

2 3 4

UTILISEZ DE L’ALCOOL DÉNATURÉ SEULEMENT.

ATTENTION: CET APPAREIL N’A PAS ÉTÉ TESTÉ POUR UNE UTILISATION AVEC DES PORTES VITRÉES. AFIN DE RÉDUIRE LE RISQUE D’INCENDIE OU DE BLESSURE, VEUILLEZ NE PAS INSTALLER DE PORTES VITRÉES.

N’UTILISEZ PAS D’APPAREIL ENCASTRABLE OU TOUT AUTRE PRODUIT NON INDIQUÉ POUR UTILISATION AVEC LE PRODUIT. CONSULTEZ LES INSTRUCTIONS D’INSTALLATION ET D’UTILISATION POUR CE MODÈLE.

DÉGAGEMENTS MINIMAUX DES MATÉRIAUX COMBUSTIBLES: WMFE 1 2,3,4

ARRIÈRE 2” 1/2” DESSOUS 6” 2” CÔTÉS 0” 12” PLAFOND / MANTEAU 18” 18” FAÇADE 36” 36”

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 4Y4 CANADA

NUR DENATURIERTES ETHANOL VERWENDEN.

WARNUNG: DIESES GERÄT IST NICHT FÜR DEN BETRIEB MIT GLASTÜREN GETESTET. ZUR VERRINGERUNG VON BRAND- ODER VERLETZUNGSGEFAHR KEINE GLASTÜREN INSTALLIEREN.

KEINEN GERÄTEEINSATZ ODER ANDERE PRODUKTE VERWENDEN, DIE NICHT ZUR VERWENDUNG MIT DIESEM PRODUKT VORGESEHEN SIND. SIEHE INSTALLATIONS- UND BEDIENUNGSANLEITUNGEN FÜR DIESES MODELL.

MINDESTABSTAND ZU BRENNBAREN MATERIALIEN EINHALTEN: WMFE 1 2,3,4

RÜCKSEITE 5,1 cm 1,3 cm UNTERSEITE 15,2 cm 5,1 cm SEITEN 0 cm 30,5 cm DECKE / KAMINSIMS 47,7 cm 45,7 cm VORDERSEITE 91.4 cm 91.4 cm

W385-0552

W415-0958 / C / 03.01.12

3.0 LOCATING APPLIANCE

DUE TO HIGH TEMPERATURES, THIS APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC. KEEP

COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS, CLOTHES AND

CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER WATER CON-

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE APPLIANCE MUST NOT BE

INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED OVERHEATING

COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

APPLIANCE MUST BE ANCHORED ON A SOLID PERMANENT WALL.

CHECK REGULARLY THAT THE APPLIANCE REMAINS FIRMLY ANCHORED.

INSTALL IN AN AREA WITH LIMITED/RESTRICTED ACCESS TO CHILDREN AND PETS.

ALL CLEARANCES TO COMBUSTIBLES MUST BE MAINTAINED.

THIS APPLIANCE MUST BE INSTALLED IN A WELL VENTILATED AND EASILY ACCESSIBLE AREA

FOR EASE OF FILLING, IGNITION AND EXTINGUISHING OF THE APPLIANCE.

WARNING

TAINER.

W415-0958 / C / 03.01.12

4.0 INSTALLATION

4.1 MINIMUM CLEARANCE TO COMBUSTIBLES

WMFE1 WMFE2, WMFE3, WMFE4

SIDES 0" 12" BACK 2" 1/2" TOP 18" to mantel 18" to mantel TOP 18" to ceiling 18" to ceiling FRONT 36" 36" BOTTOM 6" 2"

18”

MIN.

WMFE1

WMFE2, WMFE3, WMFE4

18”

MIN.

6”

MIN.

0”

W415-0958 / C / 03.01.12

2”

MIN.

2”

1/2”

12”

MIN.

WMFE2 ILLUSTRATED

4.2 INSTALLING THE APPLIANCE

4.2.1 WMFE1

NOTE: Wood screws are provided for securing to wooden studs or framework. Use the appropriate anchors

for cement, stone or drywall (hardware not supplied).

4 1/4”

MOUNTING

22”

BRACKETS

22”

A. Select a location that is not prone to moisture and is located at least 36" away from combustible materials such as curtain drapes, furniture, bedding, paper, etc. B. Have two people hold the appliance against the wall to determine the ﬁ nal location. C. Secure the 4 mounting brackets as illustrated using appropriate mounting hardware for your application. All fasteners must be well secured into the wall. NOTE: The top mounting brackets must be installed with the ﬂ anges pointing up. The bottom mounting brackets must be installed with the ﬂ anges pointing down. D. Lift the appliance into place, making sure the brackets on the top of the appliance engage over the mounting bracket ﬂ anges. Brackets may need to be adjusted to keep the appliance tight to the wall. E. Attach the two brackets (supplied) to the bottom of the appliance so the ﬂ anges engage the wall mounting brackets. This prevents the appliance from lifting off the wall.

TOP VIEW BOTTOM VIEW

W415-0958 / C / 03.01.12

4.2.2 WMFE2, WMFE3 AND WMFE4

NOTE: Wood screws are provided for securing to wooden studs or framework. Use the appropriate anchors for cement, stone or drywall (hardware not supplied). A. Select a location that is not prone to moisture and is located at least 36" away from combustible

materials such as curtain drapes, furniture, bedding, paper, etc.

B. Have two people hold the appliance against the wall to determine the ﬁ nal location. C. Secure the 2 mounting brackets as illustrated using appropriate mounting hardware for your

application. All fasteners must be well secured into the wall.

D. Lift the appliance into place, making sure the tabs engage into the mounting slots on the rear of the

appliance.

E. Secure the 2 top mount brackets to the back edge of the appliance then to the mounting bracket. This

prevents the appliance from lifting off the wall.

MOUNTING

SLOTS

MOUNTING BRACKETS

TABS

15” (WMFE2,3) 243/4” (WMFE4)

TOP MOUNT BRACKET

MOUNTING BRACKET

W415-0958 / C / 03.01.12

5.0 FINISHING

5.1 BURN POT / BURNER INSTALLATION

The plastic ﬁ lm MUST be removed from the stainless steel ﬁ rebox/burner prior to operating the appliance.

When removing the plastic ﬁ lm from the stainless steel ﬁ rebox/burner, there may be traces of plastic residue which can be easily removed using stainless steel cleaner.

5.1.1 WMFE1

A. Remove the glass fender if installed. B. Place the three empty burn pots into the holes in the ﬁ rebox.

5.1.2 WMFE2, WMFE3 AND WMFE4

A. Remove the glass fender if installed. B. Position the empty burner with the locating tabs towards

the back of the ﬁ rebox.

C. Slide the locating tabs through the locating slots at the

back of the ﬁ rebox. Ensure the burner is resting ﬂ at along the ﬁ rebox bottom.

BURNER LOCATING SLOT

BURNER LOCATING TAB

W415-0958 / C / 03.01.12

5.2 GLASS FENDER INSTALLATION

A. Place the glass retaining pins into the holes with the set screws facing forward, as illustrated. B. Slide the glass fender into the slots of the glass retaining pins. Center the glass. C. Carefully tighten the set screws, making sure not to break the glass. D. Lift the glass fender assembly out of the holes and rotate it 180°, so the set screws are facing the back

of the appliance.

180°

5.3 WARNING PLATE LOCATION

The warning plate is located at the front edge of the appliance. Pull it up, through the slot and tilt it back to read. You may ﬁ nd it easier to access with the glass fender removed.

W415-0958 / C / 03.01.12

6.0 OPERATING INSTRUCTIONS

6.1 FILLING THE BURNER / BURN POT

WARNING

YOU MUST BE 18 YEARS OF AGE TO OPERATE THIS APPLIANCE.

NEVER ALLOW CHILDREN OR OTHER AT RISK INDIVIDUALS TO FILL THE BURNER WITH FUEL

OR OPERATE IT.

NEVER POUR FUEL INTO A BURNING FLAME.

USE DENATURED ETHANOL (ETHYL ALCOHOL) FUEL ONLY.

NEVER USE GELLED ETHANOL FUELS. ONLY LIQUID FUELS ARE TO BE USED.

NEVER USE GASOLINE

ALLOW BURNER / BURN POT TO COOL BEFORE FILLING.

ONLY POUR THE QUANTITY OF FUEL TO BE BURNED INTO THE BURN POT. IT IS RECOMMENDED

TO BURN THE FUEL UNTIL THE FUEL IS COMPLETELY CONSUMED.

DO NOT OVER FILL.

SPILLED FUEL MUST BE REMOVED WITH AN ABSORBENT CLOTH AND CLEANED TO PREVENT

IGNITION OUTSIDE THE BURNER / BURN POT. DISPOSE OF THE CLOTH IN A SAFE MANNER AND

KEEP AWAY FROM APPLIANCE WHILE LIGHTING.

DO NOT ATTEMPT TO POUR FUEL BACK INTO THE ETHANOL CONTAINER. THE BURN POT IS NOT

DESIGNED FOR POURING.

6.1.1 WMFE1

DO NOT REMOVE THE BURN POT FROM THE APPLIANCE TO FILL. MOVING THE BURN POT BACK INTO POSITION

IMPORTANT: Do not refuel the appliance when it is burning or still hot. Flames may not be readily visible, you must always check for heat from the burner area. If there is any sign of heat, do not refuel.

NOTE: Light the appliance immediately after filling burn pot with fuel. Vapour may build up causing a harsh ignition.

A. Lift the glass fender assembly up and out of the appliance. B. Screw the ﬁ lling spout (provided) to the ethanol container, making sure it doesn't leak. C. With the spout fully extended and bent at a 90° angle, place the end of the spout into the burn pot and

pour the quantity of fuel to be burned. The maximum ﬁ ll level is 1/4" below the burner ring. Care must be taken not to ﬁ ll above the burner ring. DO NOT OVERFILL.

GLASS FENDER ASSEMBLY

WARNING

MAY CAUSE SPILLAGE.

BURNER RING

MAX FILL LEVEL

1/4”

BURN POT

W415-0958 / C / 03.01.12

6.1.2 WMFE2, WMFE3 AND WMFE4

DO NOT REMOVE THE BURN POT FROM THE APPLIANCE TO FILL. MOVING THE BURN POT BACK INTO POSITION

NOTE: Light the appliance immediately after filling burn pot with fuel. Vapour may build up causing a harsh ignition.

A. Lift the glass fender assembly(s) up and out of the appliance. B. Position the burner slide in the fully open position. C. Screw the ﬁ lling spout (provided) to the ethanol container, making sure it doesn't leak. D. With the spout fully extended and bent at a 90° angle, place the end of the spout into the burner

housing. Pour the fuel until it reaches the ﬂ ame diverter. NOTE: The ﬂ ame diverter is marked "MAX FILL LEVEL". DO NOT OVERFILL.

WARNING

MAY CAUSE SPILLAGE.

FULLY OPEN

GLASS FENDER ASSEMBLY

BURNER SLIDE

MAX FILL LEVEL

FULLY CLOSED

FLAME DIVERTER

W415-0958 / C / 03.01.12

6.2 IGNITION

YOU MUST BE 18 YEARS OF AGE TO OPERATE THIS APPLIANCE.

NEVER ALLOW CHILDREN OR OTHER AT RISK INDIVIDUALS TO IGNITE THE FUEL OR OPERATE

NEVER LIGHT APPLIANCE WHEN HOT.

BEFORE IGNITION, ENSURE THERE IS NO EXCESS FUEL ON ANY OF THE SURFACES

SURROUNDING THE BURNER OPENING. ALL EXCESS FUEL MUST BE REMOVED USING A CLOTH

AND CLEANED TO PREVENT IGNITION OUTSIDE THE BURNER HOUSING. DISPOSE OF THE

CLOTH IN A SAFE MANNER AND KEEP AWAY FROM APPLIANCE WHILE LIGHTING.

ALL FUEL CONTAINERS/ACCESSORIES MUST BE STORED A SAFE DISTANCE AWAY FROM THE

BURNER SLIDE MUST BE FULLY OPEN BEFORE LIGHTING. (IF APPLICABLE).

NEVER USE A SPARK TYPE IGNITOR. ONLY USE A FLAME TYPE IGNITOR.

ALWAYS BRING THE IGNITION FLAME TO THE FUEL. DO NOT TRY TO LIGHT THE IGNITOR WITH IT

A. Standing to the side of the appliance, light a long lighter and then position near the fuel. Always make

sure you are a safe distance from the burner opening.

NOTE: You may ﬁ nd it easier to light the fuel with the glass fender removed.

IT MAY TAKE 15-20 MINUTES TO REACH MAXIMUM FLAME HEIGHT. THE APPLIANCE MAY EMIT A SLIGHT, HARMLESS ODOUR WHEN FIRST USED. THIS ODOUR IS

NORMAL. EXPANSION/CONTRACTION NOISES DURING HEATING UP AND COOLING DOWN CYCLES ARE

NORMAL AND EXPECTED.

6.3 EXTINGUISHING THE FLAME

WARNING

IT.

APPLIANCE.

CLOSE TO THE FUEL.

IF POSSIBLE LET THE FUEL BURN OUT COMPLETELY, THIS WILL PREVENT ODOURS, BUILD UP

IF FLAME IS OUT OF CONTROL, USE ONLY A TYPE ABC DRY CHEMICAL FIRE EXTINGUISHER

NOTE: In case the ﬂ ame doesn't extinguish immediately leave the diverter/cover closed for 15 minutes,

allowing the fuel to cool, then repeat steps below..

6.3.1 WMFE1

To extinguish the ﬂ ames, slide the burner cover out from underneath the appliance. Flip it over and cover the ﬂ ames.

WARNING

NEVER EXTINGUISH THE FLAME WITH WATER.

OF VAPOURS AND POSSIBLE RE-IGNITION.

(MINIMUM SIZE 2.5 LBS) TO EXTINGUISH THE FLAME.

ALWAYS HAVE AN EXTINGUISHER READILY AVAILABLE NEAR THE APPLIANCE.

SLIDE TO THE RIGHT

BURNER COVER

W415-0958 / C / 03.01.12

6.3.2 WMFE2, WMFE3 AND WMFE4

To extinguish the ﬂ ames pull the shut-off key from the magnet located underneath the appliance. Position the slot on the key over the ﬂ ame diverter handle (under the glass fender) and pull forward until closed.

MAGNET

SHUT-OFF KEY

FLAME DIVERTER HANDLE

7.0 MAINTENANCE

NEVER CLEAN THE BURNER IF IT STILL CONTAINS FUEL. LIGHT AND BURN OFF ANY FUEL

ALLOW BURNER / BURN POT TO COOL BEFORE CLEANING.

It is recommended that the empty burner housing be cleaned after every use using a soap and warm water solution. The burner housing must be completely dry before reﬁ lling. Manufacturer is not responsible for damages caused by the use of inappropriate cleaning products.

7.1 CARE OF STAINLESS STEEL

Stainless steel tends to oxidize or stain in the presence of chlorides and sulﬁ des, particularly in coastal areas and other harsh environments, such as the warm, highly humid atmosphere around pools and hot tubs. These stains could be perceived as rust, but can be easily removed or prevented. To provide stain prevention and removal, wash all stainless steel surfaces every 3-4 weeks or as often as required with fresh water and/or stainless steel cleaner.

CLEANING THE STAINLESS STEEL SURFACE:

Do not use abrasive cleaners or steel wool on the stainless steel parts. Doing so will scratch the ﬁ nish. Sur- faces should be cleaned with warm soapy water while the metal is still warm to the touch. To clean stainless surfaces, use a stainless steel or non-abrasive cleaner. Always wipe in the direction of the grain. Over time, stainless steel parts discolour when heated, usually to a golden or brown hue. This discolouration is normal and does not affect the performance of the appliance.

WARNING

BEFORE CLEANING.

81.1

W415-0958 / C / 03.01.12

8.0 REPLACEMENT PARTS

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMA TION, CONTACT YOUR AUTHORIZED DEALER.

COMPONENTS

REF NO. PART NO. DESCRIPTION

1 W300-0143 GLASS FENDER 2 W515-0006 GLASS RETAINER 3 4 W010-2461 BURN POT (WFME1) 5 W010-2432 BURNER (WMFE2, 3, 4) 6 W080-1140 WALL MOUNT BRACKET (WMFE1) 7 W655-0368 WALL MOUNT BRACKET (WMFE2, 3, 4) 8 W715-0861 SIDE TRIM (WMFE2, 3) SPECIFY COLOUR 9 W715-0860 TOP/BOTTOM TRIM (WMFE2) SPECIFY COLOUR 10 W715-0863 TOP/BOTTOM TRIM (WMFE3) SPECIFY COLOUR 11 W080-1143 TOP MOUNTING BRACKET (WMFE2, 3, 4)

W365-0003 SHUT OFF KEY

WARNING

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

41.1

W415-0958 / C / 03.01.12

9.0 TROUBLESHOOTING

TURN OFF THE APPLIANCE COMPLETELY AND LET IT COOL BEFORE SERVICING. ONLY A

QUALIFIED SERVICE PERSON SHOULD SERVICE OR REPAIR THE APPLIANCE.

SYMPTOM PROBLEM TEST SOLUTION

Smoke or smell coming from the burner/appliance.

Flame is very active going from side to side.

Flames will not extinguish when turned off.

Burner won’t light. Insufﬁ cient fuel. - Fill to appropriate level.

Spilled fuel Spilled fuel - Remove all ignition sources.

Build up of dust or dirt on appliance.

Foreign material in burn pot / burner.

Incorrect fuel being used - Use only denatured ethanol Appliance was just turned

off. Draft blowing on the

ﬂ ame. (ie. Ceiling fan, open window etc.)

Overﬁ lled burn pot / burner.

Flame diverter pulled too slowly, allowing vapour to build up and burn through the cracks.

Foreign material obstructing ﬂ ame diverter, not allowing it to close.

Fuel is too cold. - Allow some time for it to warm up. Flame diverter is not fully

open. Incorrect fuel being used - Use only denatured ethanol.

WARNING

- Clean the appliance

- Clean burn pot / burner

- The smell only lasts for a short period of time.

- Remove any air inﬂ uence or relocate the appliance when cool.

- People walking too close to the appliance. Relocate to a low trafﬁ c area when cool.

- Fill to appropriate level.

- Allow fuel to burn out completely.

- Open the ﬂ ame diverter, allow the ﬂ ame to settle and then close with a faster motion.

- Allow fuel to burn out completely.

- Clean burner.

- Open ﬂ ame diverter completely.

- Clean using an absorbant cloth to prevent ignition. Dispose of cloth in a safe manner and keep away from the appliance and ignition sources.

- Ventilate where spill occured.

- Only light the appliance when 100% sure spill has been cleaned up.

W415-0958 / C / 03.01.12

42.21A

10.0 WARRANTY

NAPOLEON® ethanol appliances are manufactured under the strict Standard of the world recognized

NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen who take

great pride in their work. Once assembled the complete appliance is thoroughly inspected by a qualiﬁ ed technician before

packaging to ensure that you, the customer, receives the quality product that you expect from NAPOLEON®.

NAPOLEON® ETHANOL APPLIANCE 2 YEAR LIMITED WARRANTY

All stainless steel components of your new NAPOLEON® ethanol appliance are warranted against defects for two years from date of purchase. * All other components are warranted against defects for 90 days from date of purchase. All repair work must be done through an authorized Napoleon Dealer. * Construction of models vary. Warranty applies only to components included with your speciﬁ c appliance.

NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an authorized NAPOLEON® dealer your appliance is subject to the following conditions and limitations: Warranty coverage begins on the date of purchase. This limited warranty applies only while the unit remains at the site of original installation, and only if the unit is installed in Canada or the United States. This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives. Installation must be done in accordance with the installation instructions included with the product and all local and National building and ﬁ re codes. This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other manufacturers will nullify this warranty. This limited warranty further does not cover any scratches, dents, corrosion or discolouring caused by excessive heat, abrasive and chemical cleaners. This warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been operated in accordance with the operation instructions and under normal conditions. With respect to this Limited Warranty, NAPOLEON® may, at its discretion, fully discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s). NAPOLEON® will not be responsible for installation, labour or any other costs or expenses related to the reinstallation of a warranted part, and such expenses are not covered by this warranty. Notwithstanding any provisions contained in this Limited Warranty, NAPOLEON’S responsibility under this warranty is deﬁ ned as above and it shall not in any event extend to any incidental, consequential or indirect damages. This warranty deﬁ nes the obligations and liability of NAPOLEON® with respect to the NAPOLEON® ethanol appliance and any other warranties expressed or implied with respect to this product, its components or accessories are excluded. This limited warranty does not cover damages resulting from the use of components not supplied with the appliance, or the use of fuel other than those speciﬁ ed. Any damages to appliance due to weather, long periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®. All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation. The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or replace such defect. Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without authorization will be refused and returned to sender. Shipping costs are not covered under this warranty. Additional service fees may apply if you are seeking warranty service from a dealer. Labour, travel, diagnostic tests, shipping and other related charges are not covered by this warranty. This warranty does not cover any service calls to correct installation or use of this appliance.

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS.

NAPOLEON® IS A REGISTERED TRADEMARK OF WOLF STEEL LTD.

ISO 9001 : 2008 Quality Assurance Certiﬁ cate.

CONDITIONS AND LIMITATIONS

2.14A

W415-0958 / C / 03.01.12

11.0 SERVICE HISTORY

W415-0958 / C / 03.01.12

43.1

+ 44 hidden pages

Napoleon Fireplaces WMFE1 User Manual [en, de, fr]

Specifications and Main Features

Frequently Asked Questions

User Manual