Napoleon NEFI18H Installation Manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

EN

OPERATING INSTRUCTIONS

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278

NEFI18H

ELECTRIC LOG SET INSERT

FR
PG
23

SAFETY INFORMATION

!

WARNING

If the information in these instructions
are not followed exactly, a fi re may result
causing property damage, personal injury
or loss of life.

- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone [phone] • Fax [phone] • www.napoleonfi replaces.com •[e-mail]

$10.00

1.16F

W415-1654 / B / 10.24.16

EN

2

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 5

1.3 GENERAL INSTRUCTIONS 5

1.4 RATING PLATE INFORMATION 6

1.5 LABEL LOCATION 6

2.0 LOCATING LOG SET 7

2.1 UNPACKING AND TESTING LOG SET 7

2.2 GROUNDING LOG SET 7

3.0 INSTALLATION 8

3.1 LOG SET INSTALLATION 8

3.1.1 INSTALLING LOG SET INTO EXISTING FIREPLACE 8

3.1.2 INSTALLING LOG SET INTO MANTEL 9

3.2 HARD WIRING INSTALLATION 10

4.0 OPERATING INSTRUCTIONS 11

4.1 OPERATING CONTROL PANEL 11

4.2 OPERATING BY REMOTE CONTROL 12

4.3 REMOTE BATTERY INSTALLATION 12

5.0 FINISHING 13

5.1 NEFI18H LOG PLACEMENT 13

5.2 CHARCOAL EMBER PLACEMENT 14

6.0 WIRING DIAGRAM 15

7.0 REPLACEMENT PARTS 16

7.1 NEFI18H OVERVIEW 16

8.0 TROUBLESHOOTING 18

9.0 WARRANTY 19

10.0 NOTES 20

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

W415-1654 / B / 10.24.16

Batteries must be disposed of according to the local laws and regulations. Some batteries may be
recycled, and may be accepted for disposal at your local recycling center. Check with your municipality
for recycling instructions.

1.0 INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF
CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fi re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.

• Clothing or other fl ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of traffi c and away from furniture and
draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children
from hot surfaces. These screens and guards must be fastened to the fl oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance
and are kept clean. The appliance should be inspected before use and at least annually by a qualifi ed
service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding
material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and
other fl ammable vapors and liquids.

• Under no circumstances should this appliance be modifi ed.

• Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician
to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the
glass should be done by a licensed or qualifi ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traffi c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fi re, or damage the appliance.

• To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or
relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the
appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,
discolouration or damage to decorations, a T.V. or other electronic components.

!

WARNING

3

EN

3.7C

W415-1654 / B / 10.24.16

EN

4 5/8"

117mm

13 1/2"

343mm

10"

254mm

13"

331mm

18"

457mm

16 9/16"

1 3/8"

421mm

34mm

FRONT VIEW RIGHT SIDE VIEW TOP VIEW

HARDWIRE JUNCTION BOX

OR POWER CORD

4

1.1 DIMENSIONS

W415-1654 / B / 10.24.16

5

1.2 LISTING APPROVALS

This log set has been tested in accordance with the CSA and
UL Standards for fi xed and location-dedicated electric room
appliances in the United States and Canada. If you need
assistance during installation, please contact your local dealer.

NOTE: This log set must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest
edition in the United States or the Canadian Electric Code,
CSA C22.1 in Canada.

1.3 GENERAL INSTRUCTIONS

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL
ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

A. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B. The appliance may emit a slight, harmless odour when fi rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C. If your appliance does not emit heat, consult the operation section of this manual for further

information.

D. Use with a CSA- or UL-certifi ed surge protector.
E. Do not route the power cord directly underneath the appliance.

Model Number

Description

Voltage

Appliance Width

Appliance Height

Appliance Depth

Net Weight

Gross Weight

!

WARNING

AND/OR PROPERTY DAMAGE.

RESULT IN A SAFETY HAZARD.

POWER SUPPLY CIRCUIT.

RECEPTACLE AND FULLY INSERT.

Watts

Amps

NEFI18H

18" Electric
Logset Insert

120V AC

1500W

15 AMP Ground­ed Circuit

18" (457mm)

13.5"
(343mm)

13" (330mm)

22.5lbs (10.2kg)

27.6lbs (12.5kg)

EN

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured
homes when installed according to these instructions.

4.8B

As with most electronic devices, your new log set has been designed to operate at temperatures between 5°C
(41°F) and 35° C (95°F). During the colder winter months, allow the log set to reach room temperature before
turning it on.

W415-1654 / B / 10.24.16

6

FOYER À ÉLECT

FOYER À ÉLECT

APPROPAPPROP

60Hz 60H

:POWER:

150 150

MODÈLE:

1.4 RATING PLATE INFORMATION

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 1278 /

EN

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 1278

ELECTRIC FIREPLACE. SUITABLE FOR
BEDROOM AND BED-SITTING ROOM
INSTALLATION. SUITABLE FOR MOBILE
HOME INSTALLATION.

FOYER À ÉLECTRIQUE. HOMOLOGUE POUR
INSTALLATION DANS UNE CHAMBRE A
COUCHER, UNE SALLE DE BAIN ET UN STUDIO.
APPROPRIE POUR INSTALLATION DANS UNE
MAISON MOBILE.

WOLF STEEL LTD.

24 NAPOLEON ROAD,
BARRIE, ON, L4M 0G8 CANADA

MASTER CONTRACT: 161746

FREQUENCY: 60Hz FRÉQUENCE: 60Hz
POWER: 1500W PUISSANCE: 1500W
DATE CODE: XXXXX CODE DE DATE:
DESIGNED IN NORTH AMERCIA
BY WOLF STEEL LTD.
MADE IN CHINA

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model of the appliance.

For rating plate location, see “LABEL LOCATION” section.
This illustration is for reference only. Refer to the rating plate on the log set for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

NOTE: Do not use the log set during mobile home transportation.

1.5 LABEL LOCATION

"DO NOT COVER"

LABEL (W385-1946)

MODEL / MODÈLE:

VOLTAGE: 120 VAC TENSION: 120VCA

ATE CODE:

120 VAC

OWER

SERIAL NUMBER/NO. DE SERIE:

CONTRAT-CADRE: 161746

NEFI18H

DESIGN AMERIQUE DE NORD
PAR WOLF STEEL LTD.
FABRIQUE EN CHINE

NEFI18

W385-2143

ATTENTION

LABEL

(W385-2133)

WARNING

LABEL

(W385-1943)

W415-1654 / B / 10.24.16

FRONT

RATING PLATE WITH

SERIAL NUMBER

NEFI18H (W385-2143)

WARNING LABEL

(W385-1944)

CAUTION LABEL

(W385-1945)

HARD WIRING

LABEL

(W385-2003)

RIGHT SIDELEFT SIDE

2.0 LOCATING LOG SET

!

WARNING

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

2.1 UNPACKING AND TESTING LOG SET

Carefully remove the appliance from the box and remove the support brackets. Prior to installing the
appliance, remove all packaging material and test to make sure the appliance operates properly by plugging
the power supply cord into a conveniently located 120V, 15 Amp minimum grounded outlet.

7

EN

2.2 GROUNDING LOG SET

This appliance is for use on 120 volts. The cord has a plug
as shown in (A). An adapter as shown in (C) is available for
connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding plug extending from the
adapter must be connected to a permanent ground such as
a properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove
plug from outlet.

NOTE: Must be connected to a dedicated 15 amp circuit.
The use of an extension cord is NOT permitted.

GROUNDING METHODS

METAL SCREW

(A)

COVER OF

GROUNDED

OUTLET BOX

GROUNDING PIN

(C)

GROUNDING

(B)

ADAPTER

MEANS

NOT ALLOWED IN CANADA

96.1

W415-1654 / B / 10.24.16

8

3.0 INSTALLATION

EN

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

NOTE: Follow all National and local electrical codes.

!

WARNING

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

3.1 LOG SET INSTALLATION

The log set can be installed in any location. It is suggested to install the log set into an existing fi replace or a
wood mantel for aesthetic purposes. When installed, ensure the log set is stable and not apt to tip.

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture, and high
traffi c areas.

3.1.1 INSTALLING LOG SET INTO EXISTING FIREPLACE

NOTE: Clean fi replace prior to installing log set to prevent debris and/or ash from entering the heater.

A. The log set insert must be installed in an opening with the minimum cavity sizes shown below:

MINIMUM FIREPLACE CAVITY SIZE

HEIGHT WIDTH DEPTH

LOG SET A B C

NEFI18H 14"

(356mm)

B. Place the log set in a position which provides optimum fl ame performance. To achieve fl ame
effect, the log set should be 2" away from the rear wall.

NOTE: Seal all chimney drafts with non-combustible materials to prevent any chimney debris from
falling onto the log set. Cap the top of the chimney fl ue to prevent rain from entering.

18"

(472mm)

14"

(356mm)

Do not install the
log set into a cavity
smaller than that
referenced in the
table.

A

B

C

Plug the log set into an outlet which has a 15Amp, 120V rating. If it is necessary to hard wire the log set, see
"HARD WIRING INSTALLATION" section.

WARNING: Due to the high temperatures, do not use existing fi replace doors which close or seal off
the log set. If installed behind any fi replace door, allow heat to be exhausted. If using existing screens,
the screen must provide adequate airfl ow in front of the log set.

W415-1654 / B / 10.24.16

3.1.2 INSTALLING LOG SET INTO MANTEL

!

!

NOTE: To prevent damaging the base of the mantel, carefully lift the log set into the mantel while
avoiding contact with the front edge of the mantel base.

A. Lift the log set up and insert into the opening. Do not push or slide the bottom of the log set on the

fl oor base (Figure 1).

B. Set the log set down and into place (Figure 2).

NOTE : To achieve fl ame effect, the log set should be 2" away from the rear wall.

9

EN

Fig. 1

NE GLISSEZ PAS L'APPAREIL

DO NOT SLIDE LOGSET

MANTEL

STEP 2: INSERT

STEP 1: LIFT

Fig. 2

MANTEL

STEP 3:

SET APPLIANCE

W415-1654 / B / 10.24.16

10

BLACK

WHITE

GREEN

GREEN

BLACK

WHITE

BLACK

WHITE

GREEN

3.2 HARD WIRING INSTALLATION

EN

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

HARD WIRING CONNECTION

If it is necessary to hard wire the appliance, a qualifi ed electrician must remove the cord connection, and wire
directly to the household wiring. The wire and power supply breaker must be rated for 120V and a minimum
of 15 Amps.

This log set must be electrically connected and grounded in accordance with local codes, if hard wired. In
the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the
current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

NOTE: There are 3 wires from the appliance junction; white (neutral), black (power L1) and green
(ground) that connect to 120V power supply (breaker panel), see below.

!

WARNING

White, Green and

Black wires:

Connect to 120V

power supply.

A. Remove the securing screws (2) from the electrical cover plate, located on the rear of the log set.
B. Add an electrical box connector and feed the supply wires through the 7/8" (22mm) hole.
C. Separate the black, white and green wires that have the wire nuts on them.
D. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the

power supply. Connect the white wire from the appliance to the white (neutral) wire from the
power supply. Connect the green wire to the ground wire.

E. Resecure the cover plate.

'

+

*

6

3

/

&

$

1

5

­*

"

0

$

/

&

W415-1654 / B / 10.24.16

BLACK

WHITE

GREEN

(L1)

(N)

(G)

WIRE NUT

BLACK

WHITE

GREEN

8

4

1

6

0

1
1

&

-

3

:

NOTE: To aid with
moving the appliance,
leave enough wire so
that the log set can
be removed from the
enclosure without
disconnecting the
power supply. If
servicing, shut off
power supply.

4.0 OPERATING INSTRUCTIONS

11

Once the log set has been plugged into a grounded electrical outlet or hard wired to a dedicated grounded
120V power supply, it is ready to operate.

ATTENTION: Ensure the house circuit breakers for the power supply are turned on. When initially
connecting the appliance into a power source, the appliance will perfom an LED check. The appliance
will fl ash on and off for 5 seconds then remain off until turned on by control panel or remote.

4.1 OPERATING CONTROL PANEL

The Control Panel is located on the front of the log set.

POWER

FLAME & EMBER LIGHT
CONTROL

HEATER CONTROL

TIMER

F° / C° SWITCH

HEATER LOCK

TEMPERATURE
CONTROL

Hold 5

seconds

Hold 5

seconds

Hold 5

seconds

Turns the appliance ON/OFF.

Controls Flame brightness and the Ember Light.
5 Settings: Flame & Ember off (FO), Ember on but Flame

off (LL), small Flame & Ember (F1), medium Flame &
Ember (F2), brightest Flame and Ember (F3).
Default setting is (F3).

Turns the Heater and Blower ON/OFF.
4 Settings: Heater & Blower off (HO), Blower on (BL), low

heat (H1), high heat (H2).
Default setting is (HO).

Timer can be programed to run appliance for specific
lengths of time (30mins. minimum to 6hrs maximum).
Default setting is Timer de-select.

To change temperature format, Fahrenheit or Celsius.
Press and hold the Flame button for 5 seconds.
Default setting is Fahrenheit.

Heater button can be locked or unlocked by holding the
Heater button for 5 seconds.
Default setting is heater unlock

Press and hold the Timer button for 5 seconds. This
will change the button to Temperature Control, or vice
versa. There are 7 temperature settings (61
75

°F, 81°F, 85°F and OFF).

Default setting is de-select Temperature Control.

°F, 64°F, 70°F,

EN

W415-1654 / B / 10.24.16

EN

12

4.2 OPERATING BY REMOTE CONTROL

!

WARNING

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND

CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.

KNOT BEFORE THROWING AWAY.

NOTE: When operating the remote control, it must be directed towards the front center of the log set.

A. The power button can be used to turn the log set on/off. Pressing

this button activates the power to the log set. Pressing the
power button again will turn off the log set. The ember and log will
fade after 4 seconds after turning off the log set.

B. To adjust the fl ame brightness and ember log light, press the fl ame

button . There is one ember log light and three fl ame brightness
levels to cycle through and then an off setting (LL, F1, F2, F3 and
then F0). F3 is the brightest fl ame level, LL is the ember log light
only.

C. To control the thermostat function, press the thermostat

button . There are 7 temperature settings (61°F, 64°F, 70°F, 75°F,
81°F 85°F and off). The default setting will display Fahrenheit. Press
the thermostat button to cycle through the settings. Once you have
selected the desired temperature, the heater will automatically
operate until that temperature is reached. When the room
temperature is 2 degrees lower than the temperature setting, the
heater will turn on.

D. To activate the heater and blower, press the heater button , the

blower will turn on. Press the heater button again to set desired low

or high heat temperature; press the heater button again to turn off
the heater.

E. The timer controls all operating modes of the log set. To activate the

timer, press the timer button , the icon will illuminate and the time will appear on the LED display.
To choose the desired time, continue to press the timer button, there are 8 settings (30mins,1h, 2h,
3h, 4h, 5h, 6h and off). The fi replace will turn off at the setting time.

F. To turn off the log set, press the power button once on the remote, or press the power button once

on the control panel on the appliance.

NOTE: This handheld remote control must remain within 6 meters or 19 feet of the log set to be
effective.

4.3 REMOTE BATTERY INSTALLATION

1. To replace the existing battery, remove the battery
holder.

2. To remove the battery holder, turn remote onto
front side and press the left side lever towards the
center while pulling the battery holder out using the
slot provided.

3. Replace existing battery, type CR 2025, with a
new battery and reinstall the battery holder into the
remote by sliding it into position, as shown.

4. Battery cover is secure onto the remote control
when a "CLICKING" noise is heard.

BATTERY (CR 2025)

REMOTE

(REAR SIDE)

W415-1654 / B / 10.24.16

BATTERY COVER

5.0 FINISHING

13

!

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

5.1 NEFI18H LOG PLACEMENT

1 2

#1

PIN

WARNING

EN

PIN

#2

Place the log (#1) onto the pins. Ensure the log is

secure onto the pins, as shown.

3 4

#3

Place the log (#2) onto the pins. Ensure the log is

secure onto the pins, as shown.

#4

Place the log (#3) into the groove. Ensure the log

is secure, as shown.

Place log (#4) into the groove. Ensure the log is

secure, as shown.

W415-1654 / B / 10.24.16

EN

14

5.2 CHARCOAL EMBER PLACEMENT

TO AVOID DANGER OF SUFFOCATION, KEEP THE PACKAGING BAG AND CHARCOAL EMBERS
AWAY FROM BABIES AND CHILDREN. DO NOT USE IN CRIBS, BEDS, CARRIAGES OR PLAY PENS.
THE BAG IS NOT A TOY. KNOT BEFORE THROWING AWAY. PREVENT EMBERS FROM BEING
SWALLOWED.

A. Place the charcoal ember around the front and sides of the fi rebox, as indicated on the diagram

below.

Fine dust found in the bottom of the bag should not be used.

NOTE: DO NOT BLOCK AIR INTAKE OPENING AND OUTLET WITH CHARCOAL EMBERS.

!

WARNING

OUTLET

OPENING

AIR INTAKE

OPENING

CHARCOAL

EMBERS

W415-1654 / B / 10.24.16