Napoleon 2300 Installation Manual

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

MODEL 2300 MEETS THE 2015 U.S ENVIRONMENTAL PROTECTION AGENCY (E.P.A) CRIB WOOD EMISSION LIMIT FOR WOOD STOVES SOLD AFTER MAY 15,

2015, 40 C.F. R. PART 60. THIS STOVE HAS BEEN TESTED AND LISTED BY INTERTEK TESTING SERVICES TO STANDARDS: CSA B366.2, ULC S627, UL 1482.

2300

PEDESTAL MODEL

SAFETY INFORMATION

WARNING

If the information in these instructions is not followed exactly ,

a ﬁ re or explosion may result causing property damage,

personal injury or death. Improper installation, adjustment,

alteration, service or maintenance can cause injury or property damage, bodily injury or even death. Please read entire manual before you install and use your appliance.

This appliance has not been tested with an unvented gas log set. Do not install an unvented gas log set into the appliance.

FR PG 37

- This appliance can be very hot when burning.

- Combustible materials such as ﬁ rewood, wet clothing, etc. placed too close can catch ﬁ re.

- Children and pets must be kept from touching the appliance when it is hot.

- The chimney must be sound and free of cracks. Before installing this unit, contact the local building or ﬁ re authority and follow their guidelines.

- Operate only with the door tightly closed.

- Burn wood behind the log retainer directly on the ﬁ rebricks.

- Do not use an elevated grate or otherwise raise the ﬁ re.

- At least 14 square inches (90.3 square centimeters) of outside air must be admitted to the room or directly to the unit through a 4” (101.6mm) diameter pipe.

- This appliance is designed to burn natural wood only. Higher efﬁ ciencies and lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

- Do not start a ﬁ re with chemicals or ﬂ uids such as gasoline, engine oil, etc.

- Do not burn trash or garbage, lawn clippings / waste, rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing asbestos, construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood or salted materials, unseasoned wood, coal, charcoal, coloured paper, cardboard, plywood or particleboard.

- Do not let the appliance become hot enough for any part to glow red.

- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C). Attempts to achieve heat output rates that exceed design speciﬁ cations can result in steel distortion and damage.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.timberwolfﬁ replaces.com • ask@timberwolfﬁ replaces.com

WARNING

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

$10.00

1.19D

W415-1473 / A / 09.30.16

TABLE OF CONTENTS

NOTE: The camera icon indicates video tutorials are available as additional reference, visit http://mynapoleon.napoleonproducts.com/download/index/44/1

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.2 SPECIFICATIONS 5

2.3 GENERAL INSTRUCTIONS 6

2.4 GENERAL INFORMATION 7

2.5 RATING PLATE INFORMATION 8

3.0 PRE-INSTALLATION PREPARATION 9

3.1 APPLIANCE PLACEMENT 9

3.2 CLEARANCE TO COMBUSTIBLES 9

3.3 FLOOR PROTECTION 10

3.4 OUTSIDE AIR 10

4.0 INSTALLATION 11

4.1 CHIMNEY 12

4.1.1 CHIMNEY CONNECTION 13

4.1.2 ADDING SECTIONS 14

4.1.3 TYPICAL THROUGH THE CEILING 15

4.1.4 TYPICAL THROUGH THE WALL 16

4.1.5 TYPICAL EXISTING MASONRY 16

5.0 FINISHING 17

5.1 DOOR REMOVAL / INSTALLATION 17

5.2 DOOR HANDLE INSTALLATION 17

5.3 BRICKS AND BAFFLE INSTALLATION 18

6.0 OPTIONAL KIT INSTALLATIONS 19

6.1 BLOWER KIT INSTALLATION 19

6.1.1 BLOWER INSTALLATION 19

7.0 OPERATION 20

7.1 OPTIMUM BURN METHOD 21

7.2 AIR CONTROL 22

7.3 FIRE EXTINGUISHERS / SMOKE & CARBON MONOXIDE DETECTORS 22

7.4 FUEL 23

7.5 LIGHTING A FIRE 23

7.5.1 FLASH FIRE 23

7.5.2 EXTENDED FIRE 24

7.6 SMOKING 24

8.0 MAINTENANCE 24

8.1 ASH REMOVAL PROCEDURES 25

8.2 CREOSOTE FORMATION AND REMOVAL 25

8.3 RUNAWAY OR CHIMNEY FIRE 26

8.4 CHIMNEY CLEANING 26

8.5 GLASS REPLACEMENT 27

8.6 GASKET REPLACEMENT 27

8.7 SECONDARY AIR MANIFOLD REPLACEMENT 28

8.8 CARE OF GLASS 29

8.9 CARE OF PLATED PARTS 29

8.10 WOOD 30

9.0 REPLACEMENTS 31

9.1 OVERVIEW 32

10.0 TROUBLESHOOTING 33

11.0 WARRANTY 34

11.0 SERVICE HISTORY 35

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

W415-1473 / A / 09.30.16

1.0 INSTALLATION OVERVIEW

Draft, see “AIR CONTROL” section.

Door, see “DOOR REMOVAL / INSTALLATION” section.

Brick and Bafﬂes, see “BRICK AND BAFFLES INSTALLATION” section.

Rating plate, see “RATING PLATE INFORMATION” section.

Blower, see “OPTIONAL BLOWER INSTALLATION” section.

Handle, see “DOOR HANDLE INSTALLATION” section.

Ash Drawer, see “ASH REMOVAL PROCEDURES" section of the manual as well as the optional ash drawer kit EP20LAD for the leg model and optional ash pan kit EP20PAD for the pedestal model.

Outside air, see “OUTSIDE AIR” section.

W415-1473 / A / 09.30.16

2.0 INTRODUCTION

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance

according to operating instructions could cause ﬁ re or injury.

• Before installing this appliance, contact the local building or ﬁ re authority and follow their guidelines.

• This appliance must be installed by a qualiﬁ ed installer.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not operate without fully assembling all components.

• Do not let the appliance become hot enough for any part to glow red.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may

be sharp.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid

burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young

children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance. Objects placed in front of the

appliance must be kept a minimum of 4 feet (1.2m) away from the front face of the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot

surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe servicing a separate solid fuel burning appliance.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should

be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all

plastic bags, these are not toys and should be kept away from children and infants.

• If the appliance is not properly installed, a house ﬁ re may result. Do not expose the appliance to the elements (ex.

rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when the appliance is used.

• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.

• Do not start a ﬁ re with chemicals or ﬂ uids such as gasoline, engine oil, etc.

• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke

spillage in your home.

• Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or too

green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote accumulation. When this is ignited it can cause a chimney ﬁ re that may result in a serious house ﬁ re.

• This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings / waste,

rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing asbestos, construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood or salted materials, unseasoned wood, coal, charcoal, coloured paper, gift wrapping, cardboard, plywood or particleboard. Burning these materials may result in release of toxic fumes or render the appliance ineffective and cause smoke.

• Burn wood directly on the ﬁ rebricks. Do not elevate grate or otherwise raise the ﬁ re.

• Do not store wood within appliance installation clearances or within the space required for re-fueling and ash removal.

• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away

from the home or structure until completely cool.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic components.

• If equipped, the catalyst must be installed and in good working order. It is recommended that the catalyst is inspected at least 3 times per heating season.

3.17G

W415-1473 / A / 09.30.16

2.1 DIMENSIONS

2.2 SPECIFICATIONS

31 3/4"

806mm

29 1/8"

740mm

178mm

25 3/8"

12 3/4"

324mm

644mm

152mm

DIA.

SPECIFICATIONS 2300

CHAMBER (D.W.H) 22 1/2” x 18” x 12” (57.2cm X 45.7cm X 30.5cm ) CAPACITY 3.0 FT3 (0.9m3) APPROX. AREA HEATED** 1000-3500 FT2 (305m2 - 1067mm2 ) MAXIMUM HEAT OUTPUT *** 85,000 BTU/Hr HEAT OUTPUT* 11,800 - 34,000 BTU/Hr DURATION LOW FIRE** 12 HRS WEIGHT w/o BRICKS 285 LBS (129kg) WEIGHT OF BRICKS 114 LBS (52kg) IDEAL WOOD LENGTH 21” (533mm)

* As tested using test method 28 ** Figures will vary considerably with individual conditions. *** Wolf Steel Ltd. estimated realistic BTU/hr with cordwood logs and regular refueling.

W415-1473 / A / 09.30.16

2.3 GENERAL INSTRUCTIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH

LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 CANADIAN

ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE ANSI/NFPA NO. 70 IN

THIS APPLIANCE HAS NOT BEEN TESTED WITH ANY VENTED OR UNVENTED GAS LOG SET. TO

REDUCE RISK OF FIRE OR PREVENT INJURY, DO NOT INSTALL A VENTED OR UNVENTED GAS LOG

BURNING YOUR UNIT WITH THE ASH DUMP DOOR OPEN OR AJAR CREATES A FIRE HAZARD THAT

MAY RESULT IN DISCOLOURATION TO THE GOLD PLATED DOOR, INTERNAL DAMAGE TO THE

DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

THIS APPLIANCE AND IT’S COMPONENTS ARE DESIGNED TO BE INSTALLED AND OPERATED AS A

SYSTEM. ANY ALTERATION TO OR SUBSTITUTION FOR ITEMS IN THIS SYSTEM, UNLESS ALLOWED

BY THESE INSTALLATION INSTRUCTIONS, WILL VOID THE LISTING AND MAY VOID THE PRODUCT

WARRANTY. IT MAY ALSO CREATE A HAZARDOUS INSTALLATION. READ THROUGH THESE

INSTRUCTIONS THOROUGHLY BEFORE STARTING YOUR INSTALLATION AND FOLLOW THEM

WARNING

THE UNITED STATES.

SET INTO THE APPLIANCE.

APPLIANCE OR A HOUSE CHIMNEY FIRE.

CAREFULLY THROUGHOUT YOUR PROJECT.

4.7

• Before beginning your installation, consult with your local building code agency or ﬁ re ofﬁ cials and insurance representative to ensure compliance.

• Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a window near the appliance.

• Remove any dust or debris off the top of the appliance before ﬁ ring the appliance as the paint will become soft as the appliance heats up and will harden as the appliance cures. To cure the paint on your appliance burn your appliance moderately hot during the ﬁ rst few ﬁ res.

• To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door every 5-10 minutes.

• For the ﬁ rst two weeks use generous amounts of fuel and burn the appliance with the damper wide open for an hour as the appliance goes through a process of eliminating moisture in the steel and ﬁ rebricks. The initial heat output will be reduced while the moisture is being drawn from the appliance and it will be necessary to build several hot ﬁ res to remove this moisture. DURING THIS PROCESS

DO NOT OVERFIRE THE APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE APPLIANCE IF THE APPLIANCE OR CHIMNEY BECOMES RED.

W415-1473 / A / 09.30.16

2.4 GENERAL INFORMATION

We suggest that our woodburning hearth products be installed and serviced by professionals who are certified in the U.S. by the National Fireplace Institute® (NFI) as NFI Woodburning Specialists or who are certified in Canada by Wood Energy Technical Training (WETT).

DO NOT OPERATE THIS APPLIANCE WITHOUT THE PEDESTAL INSTALLED.

Your appliance has been speciﬁ cally designed to meet the 2015 U.S.A. EPA particulate emission standards and has been extensively tested in Canadian and American laboratories. This system is the most efﬁ cient, simple and trouble free we know and works as follows:

The chimney vent system used on your wood burning appliance should be designed with the least amount of restriction possible to enable the exhaust products to easily ﬂ ow through it. Chimney vent systems that are too short or too long can also have an adverse affect on the ﬂ ow of exhaust through it. The wood burning appliance and chimney vent system also require a sufﬁ cient supply of combustion air not only to support the combustion in the combustion chamber but to replace the exhaust leaving it so it can ﬂ ow freely up through the vent system and out into the atmosphere. It is the correct balance of combustion air and the chimney vent system that will ensure the appliance provides you with its optimum performance.

Combustion air enters through two holes in the bottom which can be adjusted by a single air control. Air from the front hole goes up on either side of the door into a preheating airwash located across the top and then down the window to feed the ﬁ re and also to ensure that the glass remains clean. Air from this hole also feeds directly into the combustion chamber at hearth level. Secondary air from the rear hole travels up the back in the secondary air housing to the manifold located at the top and shoots out laterally to oxidize the gases below the smoke exit. The combustion chamber is lined with high temperature ﬁ rebrick on both sides, the back and across the bottom, with a layer of ﬁ bre bafﬂ es at the top to maintain a high temperature in the combustion chamber so that gases mixing with the preheated air from the secondary air manifold tube are easily ignited and burned. The appliance sides and back are shielded to direct the heat upwards and forwards into the room.

WARNING

PRIMARY AIR SECONDARY AIR

FLUE GLASS

HOT SECONDARY AIR FIBRE BRICKS REFRACTORY

2 SIDES, BACK & BOTTOM

CERAMIC GLASS

AIR CONTROL

CLOSED

OPEN

COMBUSTION AIR INTAKE

Be sure to provide sufﬁ cient combustion air. There are many other appliances in your home competing for air such as: a kitchen range hood, forced air heating devices or a bathroom exhaust fan.

Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.

After extended periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for a few hours. This is caused by dust particles on the ﬁ rebox burning off. Open a window to sufﬁ ciently ventilate the room.

CALIFORNIA PROP 65 WARNING:

Use of this product may produce smoke which contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

If optional ash drawer is purchased, ensure that the ash dump door is tightly closed, allow the door to snap shut dislodging anything (ashes or pieces of coal) that may be stuck in the opening.

If outside air is utilized, you should never experience a shortage of combustion air. If you choose not to utilize outside air and experience draft or smoking problems, you may need to open a door, a window or otherwise provide some method of supplying combustion air to the appliance.

W415-1473 / A / 09.30.16

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2015 particulate emissions standards. Not approved for sale after May 15, 2020. Certifié conforme à la norme d’ émanation de particles de 2015. Non approuvé pour la vente après le 15 mai, 2020. 40 CFR Part 60, Subpart AAA. 2.8 Grams Per Hour / 2015 Crib Wood / 2.8 Grammes par heure / Crib Wood 2015

)CK WALL (M

4545

WALL (M/L)WALL (M/L)

(

)

OLE PO

SUR UNE BA

QUI DOIT DÉPASSER LQUI DO

OR DOUDO

NTLY. UNDER CERTAIN

ITIONS OF USE CREOSOTE

NECT POWERNECT POWER

ENT ENT

OIS SEULEMENT. N’UTILISEZ PAS DE IS SEULEMENT. N’UTILISEZ PAS

CHENET OU NE SURÉLEVEZ PAS LE NET OU NE SURÉLEVEZ PAS L

RE.

ENT: RISQU

CONDITCONDI

CRÉOCRÉ

2.5 RATING PLATE INFORMATION

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

LISTED SOLID FUEL BURNING SPACE HEATER / POÊLE À COMBUSTIBLE SOLIDE

9700539 (WSL) 4001657 (NGZ)

INSTALL AND USE ONL Y IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS AND LOCAL BUILDING CODES. MINIMUM CEILING HEIGHT: 7FT (2.13m) HEARTH EXTENSION / COMBUSTIBLE FLOOR PROTECTION: IF INSTALLED ON A COMBUSTIBLE FLOOR, UNIT MUST BE PLACED ON A NON-COMBUSTIBLE FLOOR PROTECTOR EXTENDING 18” (455mm) IN FRONT AND 8” (205mm) TO THE SIDES AND BACK. CHIMNEY TYPE: MINIMUM 6” (152mm) DIAMETER APPROVED RESIDENTIAL TYPE FOR MOBILE HOME USE A CHIMNEY LISTED TO ULC S629 IN CANADA OR UL 103HT IN THE USA. CHIMNEY CONNECTOR: 6” (152mm) DIAMETER MINIMUM 24 GAUGE STEEL MINIMUM CLEARANCE FROM HORIZONTAL CONNECTOR AND CEILING 18” (455mm). DO NOT OBSTRUCT SPACE UNDER HEATER. SPECIAL METHODS ARE REQUIRED WHEN PASSING A CHIMNEY THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILDING CODES. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. FUEL: FOR USE WITH WOOD ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. WARNING: RISK OF SMOKE SPILLAGE. OPERATE ONLY WITH DOOR FULLY CLOSED. REPLACE GLASS ONLY WITH CERAMIC GLASS. DO NOT OVERFIRE. IF HEATER OR CHIMNEY CONNECTORS GLOW, YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUIL D - U P MA Y OCCUR RAPIDLY . OPTIONAL BLOWER KIT: EP-62, 115V, 60HZ, 0.82AMP. ROUTE CORD AWAY FROM UNIT. DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT.

4001659 (WUSA) 4001658 (NAC)

HOMOLOGUÉ TESTED TO: / TESTÉ SELON : UL1482 / ULC S627

POUR INSTALLATION ET UTILISATION CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET AUX CODES LOCAUX DU BÂTIMENT. HAUTEUR DE PLAFOND MINIMAL 7PI (2,13m). PROLONGEMENT D’ÂTRE/PROTECTION DU PLANCHER COMBUSTIBLE: SI INSTALLÉ SUR UN PLANCHER COMBUSTIBLE, L’APPAREIL DOIT ÊTRE PLACÉ SUR UNE PLAQUE PROTECTRICE INCOMBUSTIBLE S’ÉTENDANT SUR 18” (455mm) À L’AVANT ET 8” (205mm) À L’ARRIÈRE ET SUR LES CÔTÉS. TYPE DE CHEMINÉE: DIAMÈTRE MINIMAL DE 6” (152mm) APPROUVÉE POUR USAGE RÉSIDENTIEL. MAISON MOBILE EMPLOYEZ UNE CHEMINÉE HOMOLOGUÉE ULC S629 AU CANADA OU UL 103HT AUX ÉTATS-UNIS. RACCORD DE CHEMINÉE: DIAMÈTRE DE 6” (152mm) D’ACIER DE CALIBRE 24 MINIMUM. 18” (455mm) DE DÉGAGEMENT MINIMAL ENTRE LE RACCORD HORIZONTAL ET LE PLAFOND. NE RIEN ENTREPOSER SOUS L’APPAREIL. DES MÉTHODES SPÉCIALES SONT REQUISES LORSQU’UNE CHEMINÉE TRAVERSE UN MUR OU UN PLAFOND. VOIR LES INSTRUCTIONS ET LES CODES DU BÂTIMENT. NE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE APPAREIL. COMBUSTIBLE: POUR USAGE AVEC LE BOIS SEULEMENT. N’UTILISEZ PAS DE CHENET OU NE SURÉLEVEZ PAS LE BOIS. PRÉPAREZ LE FEU DIRECTEMENT

R L’ÂTRE.

SUR L’ÂTRE.

VERTISSEMENT: RISQUE

AVERTISSEMENT: RISQUE D’ÉCHAPPEMENT DE FUMÉE. TENIR LA PORTE FERMÉE LORSQUE LE POÊLE FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN CÉRAMIQUE SEULEMENT. NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPAREIL OU LES RACCORDS ROUGEOIENT, L’APPAREIL SURCHAUFFE. INSPECTEZ ET NETTOYEZ LA CHEMINÉE FRÉQUEMMENT. DANS CERTAINES CONDITIONS, DES DÉPÔTS DE CRÉOSOTE PEUVENT SE FORMER RAPIDEMENT. SOUFFLERIE OPTIONNELLE: EP-62, 115V, 60HZ, 0,82A. TENEZ LE CORDON ÉLECTRIQUE LOIN DE L’APPAREIL. DANGER: RISQUE DE SECOUSSE ÉLECTRIQUE. DÉBRANCHEZ AVANT DE PROCÉDER À L’ENTRETIEN.

MODEL / MODÈLE - EPA 1900

1900

CONTACT LOCAL BUILDING FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTIONS IN YOUR LOCAL AREA. A MINIMUM CLEARANCE OF 18 INCHES (457mm) TO THE CHIMNEY CONNECTOR MAY BE REQUIRED BY THE AUTHORITY HAVING JURISDICTION.

RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES DU BÂTIMENT ET DU SERVICE DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS D’INSTALLATION DANS VOTRE RÉGION. UN DÉGAGEMENT MINIMALE DE 18 POUCES (457mm) JUSQU’AU RACCORD DE LA CHEMINÉE PEUT ÊTRE EXIGÉ PAR L’AUTORITÉ AYANT JURIDICTION.

BACK WALL (M/A)

IF THE STOVE IS TO BE INSTALLED ON A COMBUSTIBLE FLOOR, IT MUST BE PLACED ON AN APPROVED NON-COMBUSTIBLE HEARTH PAD, THAT EXTENDS 8” (200MM) BEYOND THE STOVE SIDES AND BACK, AND 18” (455MM) TO THE FRONT. SI LE POÊLE EST INSTALL

I LE P

ÊTRE PLACÉ

ÊTRE PLACÉ SUR UNE BASE DE PROTECTION INCOMBUSTIBLE CERTIFÉE QUI DOIT DÉPASSER LES CÔTÉS ET L ’AMÉRE DU

ET SE PROLONGER DE 18” (455mm) SUR LE DEVANT.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL USING SINGLE OR DOUBLE WALL CHIMNEY CONNECTORS / DÉGAGEMENT MINIMAL AUX MATÉRIAUX COMBUSTIBLE AVEC DES CONDUITS DE RACCORDEMENT À PAROI SIMPLE OU À DOUBLE PAROI

THIS WOOD APPLIANCE NEEDS PERIODIC INSPECTION AND REPAIR FOR PROPER OPERATION. CONSULT THE OWNER'S MANUAL FOR FURTHER INFORMATION. IT IS AGAINST UNITED STATES FEDERAL REGULATIONS TO OPERATE THIS WOOD APPLIANCE IN A MANNER CONSISTENT WITH THE OPERATING INSTRUCTIONS IN THE OWNER'S MANUAL. CET APPAREIL AU BOIS DOIT FAIRE L'OBJET D'UNE INSPECTION ET D'UN ENTRETIEN PÉRIODIQUES POUR UN FONCTIONNEMENT ADÉQUAT. CONSULTEZ LE MANUEL D'INSTRUCTIONS POUR PLUS D'INFORMATION. LES RÈGLEMENTS FÉDÉRAUX DE L'ÉTATS-UNIS INTERDISENT D'UTILISER CET APPAREIL DE CHAUFFAGE D'UNE MANIÈRE ALLANT À L'ENCONTRE DES INSTRUCTIONS DE FONCTIONNEMENT CONTENUES DANS CE MANUEL.

BACK WALL (M/A)

BACK WALL (M/A

L M

45°

IDE WALL SIDE WALL (M/L)

É SUR UN PLANCHER COMBUSTIBLE, IL DOIT

FROM HEATER / DU POÊLE

RESIDENTIAL / RÉSIDENTIEL

A. 22IN/PO (560 mm)

B. 12IN/PO (305mm) C. 8IN/PO (205mm)

SIDE WALL (M/L)

18"

POÊLE DE 8” (200mm)

MANUFACTURE DATE: / DATE DE FABRICATION: YEAR: MONTH:

2016

243658710912111

CAUTION:

ATTENTION:

U.S. ENVIRONMENTAL PROTECTION AGENCY

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

2017 2018

HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND FURNITURE AW A Y . CONT ACT MA Y CAUSE SKIN BURNS.

QUAND L’APP AREIL FONCTIONNE, LA SURFACE DEVIENT CHAUDE. NE PAS TOUCHER. TENIR LES ENF ANTS, LES VÊTEMENTS ET LES MEUBLES À L’ÉCART . LE CONT ACT PEUT CAUSER DES BRÛLURES À LA PEAU.

EPA1900

2019 2020

W385-2032 / B

W415-1473 / A / 09.30.16

1900 SERIES RATING PLATE ILLUSTRATED

3.0 PRE-INSTALLATION PREPARATION

3.1 APPLIANCE PLACEMENT

Have an authorized dealer install the appliance. If you install the appliance yourself, have your dealer review your installation plans and/or installation. Draw out a detailed plan of the installation including dimensions and verify the dimensions with the requirements listed in this manual. You may wish to adjust the appliance position slightly to ensure the vent does not intersect with a framing member. Appliance must be positioned so that no combustibles are within, or can swing within (e.g. drapes, doors), 4 feet (1.2m) of the front of the appliance.

3.2 CLEARANCE TO COMBUSTIBLES

WARNING

DO NOT INSTALL INTO ANY AREA HAVING A HEIGHT LESS THAN 7 FEET (2.1m)

(CEILING OF ENCLOSURE TO APPLIANCE BOTTOM, EXCLUDING HEARTH HEIGHT)

67.1B

BACK WALL

SIDE WALL

PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR

SIDEWALL (A) 22" (55.9cm) 22" (55.9cm) SIDEWALL TO FLUE (B) 31 3/4" (80.6cm) 31 3/4" (80.6cm) BACK WALL (C) 12" (30.5cm) 12" (30.5cm) BACK WALL TO FLUE (D) 15 1/2" (39.4cm) 15 1/2" (39.4cm) CORNER (E) 8" (203mm) 8" (203mm) CEILING (F) 84" (2134mm) 84" (2134mm) Clearances can be reduced with shielding acceptable to local authorities. Reduced installation must comply

with NFPA 211 or CAN/CSA-B365.

SIDE WALL

W415-1473 / A / 09.30.16

3.3 FLOOR PROTECTION

EMBER PROTECTOR:

3.4 OUTSIDE AIR

This appliance must be installed on a non-combustible protector that extends to the front, sides and back of the appliance as per the minimum requirements below.

NOTE: Ember protection is required for spark and ash shielding, not for limiting ﬂ oor temperatures from the radiant heat of the appliance. The appliance was designed and safety tested so that without

any protection, the ﬂ oor will not overheat.

IF ROOM AIR STARVATION OCCURS BECAUSE THE FRESH AIR INTAKE IS BLOCKED WITH ICE,

LEAVES, ETC., OR BECAUSE THE APPLIANCE DOOR WAS LEFT OPEN, OR DUE TO A STRONG

EXHAUST FAN OPERATING ETC., DANGEROUS FUMES AND SMOKE FROM THE OPERATING

CANADA 18” (45.7cm) 8” (203.2mm) 8” (203.2mm) N/A USA 16” (40.6cm) 8” (203.2mm) 8” (203.2mm) 2” (50.8mm)

APPLIANCE COULD BE DRAWN INTO THE ROOM.

FRONT (I) SIDES (J) BACK (K) VENT (L)

MINIMUM FLOOR PROTECTION

WARNING

99.1B

The following are signs that a fresh air kit may be required:

• When there is combustion present: Wood burns poorly, smoke spills, back-draft takes place and your chimney does not draw steadily.

• In the winter there is too much condensation on the windows.

• Opening a window seems to alleviate the above symptoms.

• A ventilation system is installed in the house.

• Other devices are present that exhaust house air.

• The house has tight ﬁ tting windows and/or is equipped with a well-sealed vapour barrier.

11 11/16"

13 3/8" 340mm

If possible connect the air intake at the pedestal’s back or bottom to the outside with a 4" (102mm) diameter fresh air kit available at your local authorized dealer / distributor.

297mm

W415-1473 / A / 09.30.16

4.0 INSTALLATION

WARNING

WEAR GLOVES AND SAFETY GLASSES FOR PROTECTION.

CAREFULLY FOLLOW THE INSTRUCTIONS FOR ASSEMBLY OF THE PIPE AND OTHER PARTS

NEEDED TO INSTALL THE APPLIANCE. FAILURE TO DO SO MAY RESULT IN A FIRE, ESPECIALLY IF

COMBUSTIBLES ARE TOO CLOSE TO THE APPLIANCE OR CHIMNEY AND AIR SPACES ARE

BLOCKED, PREVENTING THE FREE MOVEMENT OF COOLING AIR.

DO NOT DRAW OUTSIDE AIR FROM GARAGE SPACES. EXHAUST PRODUCTS OF GASOLINE ENGINES

ARE HAZARDOUS. DO NOT INSTALL OUTSIDE AIR DUCTS SUCH THAT THE AIR MAY BE DRAWN

FROM ATTIC SPACES, BASEMENTS OR ABOVE THE ROOFING WHERE OTHER HEATING APPLIANCES

OR FANS AND CHIMNEYS EXHAUST OR UTILIZE AIR. THESE PRECAUTIONS WILL REDUCE THE

POSSIBILITY OF APPLIANCE SMOKING OR AIR FLOW REVERSAL. THE OUTSIDE AIR INLET MUST

REMAIN CLEAR OF LEAVES, DEBRIS ICE AND/OR SNOW. IT MUST BE UNRESTRICTED WHILE

APPLIANCE IS IN USE TO PREVENT ROOM AIR STARVATION WHICH CAN CAUSE SMOKE SPILLAGE

AND AN INABILITY TO MAINTAIN A FIRE. SMOKE SPILLAGE CAN ALSO SET OFF SMOKE ALARMS.

NEGATIVE PRESSURE WITHIN YOUR HOME MAY INADVERTENTLY AFFECT YOUR APPLIANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE APPLIANCE MUST NOT BE INSTALLED AGAINST VAPOUR BARRIERS OR EXPOSED INSULATION. LOCALIZED OVERHEATING

COULD OCCUR AND A FIRE COULD RESULT.

DO NOT USE MAKESHIFT COMPROMISES DURING INSTALLATION. DO NOT BLOCK OR RESTRICT

AIR, GRILLE OR LOUVRE OPENINGS. DO NOT ADD A HOOD.

TO PREVENT PERSONAL INJURY KEEP HAND TOOLS IN GOOD CONDITION, SHARPEN CUTTING

EDGES AND MAKE SURE TOOL HANDLES ARE SECURE.

ALWAYS MAINTAIN THE MINIMUM AIR SPACE REQUIRED TO THE ENCLOSURE TO PREVENT FIRES.

68.3C

W415-1473 / A / 09.30.16

4.1 CHIMNEY

WARNING

NEVER INSTALL A SINGLE WALL SLIP SECTION OR SMOKE PIPE IN A CHASE STRUCTURE.

THE HIGHER TEMPERATURE OF THIS SINGLE WALL PIPE MAY RADIATE SUFFICIENT HEAT TO

COMBUSTIBLE CHASE MATERIALS TO CAUSE FIRE.

DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY SYSTEM SERVING ANOTHER APPLIANCE.

TO AVOID DANGER OF FIRE, ALL INSTRUCTIONS MUST BE STRICTLY FOLLOWED, INCLUDING

THE PROVISIONS OF AIR SPACE CLEARANCE BETWEEN CHIMNEY SYSTEM AND ENCLOSURE.

TO PROTECT AGAINST THE EFFECTS OF CORROSION ON THOSE PARTS EXPOSED TO THE

WEATHER, WE RECOMMEND THAT THE CHASE TOP BE PAINTED WITH A RUST RESISTANT PAINT.

DO NOT FILL ANY FRAMED SPACE AROUND THE CHIMNEY WITH INSULATION OR ANY OTHER

MATERIAL. INSULATION PLACED IN THIS AREA COULD CAUSE ADJACENT COMBUSTIBLES TO

OVERHEAT.

MAINTAIN A MINIMUM 2” (50.8mm) AIR CLEARANCE TO ALL PARTS OF THE CHIMNEY SYSTEM AT

ALL TIMES (EXCLUDING THE CHIMNEY CONNECTOR). FAILURE TO MAINTAIN THIS 2” (50.8mm) AIR

CLEARANCE WILL CAUSE A STRUCTURE FIRE. NEVER FILL THIS SPACE WITH ANY TYPE OF MATERIAL.

DETAILED INSTRUCTIONS FOR INSTALLATION OF THE CHASE TOP, STORM COLLAR AND

TERMINATION CAP ARE PACKAGED WITH THESE PARTS. MINIMUM CLEARANCE TO

COMBUSTIBLES WILL VARY DEPENDING ON THEIR DESIGN.

DO NOT CUT RAFTERS OR CEILING JOISTS WITHOUT FIRST CONSULTING A BUILDING OFFICIAL

TO ENSURE STRUCTURAL INTEGRITY IS NOT COMPROMISED.

FIRESTOP SPACERS MUST BE USED WHENEVER THE CHIMNEY PENETRATES A CEILING/FLOOR AREA.

THE TOTAL HORIZONTAL VENT LENGTH SHOULD NOT EXCEED 40% OF THE CHIMNEY HEIGHT

ABOVE THE APPLIANCE. ALL HORIZONTAL SMOKE PIPE MUST SLOPE SLIGHTLY UPWARDS A

MINIMUM OF 1/4” (21.2mm) PER FOOT (METER) AND ALL CONNECTIONS MUST BE TIGHT AND

SECURED BY THREE SHEET METAL SCREWS EQUALLY SPACED. AN UNINSULATED SMOKE PIPE

SHALL NOT PASS THROUGH AN ATTIC, ROOF SPACE, CLOSET, OR SIMILAR CONCEALED SPACE,

OR THROUGH A FLOOR, CEILING, WALL OR PARTITION, OR ANY COMBUSTIBLE CONSTRUCTION.

DO NOT USE ANY MAKESHIFT MATERIALS DURING INSTALLATION.

63.8A

Your appliance may be connected to a factory built or masonry chimney. If you are using a factory built chimney, it must comply with ULCS629 (Canada) or UL103 HT (USA) standards. It must therefore be a 6" (152mm) HT Type (2100°F) chimney. Use only speciﬁ ed components with no substitutions. It is extremely important that it be installed according to the manufacturer's speciﬁ cations. The manufacturer's installation instructions and speciﬁ ed clearances should always be followed in accordance with local and national codes. In Canada the CSA B365 and the CSA C22.1 installation codes are to be followed. In the USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed.

Chimney and chimney connector must be in good condition and kept clean.

W415-1473 / A / 09.30.16

4.1.1 CHIMNEY CONNECTION

Your chimney connector and chimney must have the same diameter as the appliance’s exhaust ﬂ ue outlet. The appliance pipe must be made of aluminized or cold roll steel with a minimum 24 gauge thickness. It is strictly forbidden to use galvanized steel.

A 6” (152mm) diameter single wall chimney connector, used to connect the appliance to the chimney, must be installed with the crimped end toward the appliance. This will ensure that the moisture which condenses from the burning wood will ﬂ ow back into the ﬁ re chamber. Each joint in the chimney connector must be secured with at least three sheet metal screws.

For installation of your chimney connector, the following recommendations may be useful.

• The chimney connector must be short and straight. For optimum performance it is recommended that all horizontal runs have a minimum 1/4” (6mm) rise per foot, with the upper end of the section toward the chimney. For safe and proper operation of the appliance, see “INSTALLATION” instructions.

• To insure a good draft, the total horizontal vent length should not exceed 40% of the chimney height above the appliance. All horizontal smoke pipe must slope slightly upwards a minimum of 1/4” (6.4mm) per foot (meter) and all connections must be tight. In the case of vertical installation, the total length of the connector can be longer and connected without problem to the chimney at the ceiling level.

• There should never be more than two 90° elbows in the entire connector and chimney system. Never start with a 90° elbow. Always go up vertically for at least 2 feet (0.6m) from the ﬂ ue collar before using a 90° elbow.

• The connector must not pass through any combustible material, nor may it pass through a concealed space (such as an attic, roof space, or closet). If passing through a wall, ceiling, or into a masonry chimney, use either chimney components listed for that speciﬁ c use, or means acceptable to local authorities having jurisdiction over the installation.

This appliance must be connected to: A. A chimney complying with the requirements for

Type HT chimneys in the Standard for Chimneys, Factory-Built, Residential Type and Building Heating Appliance, or

B. A code-approved masonry chimney with a ﬂ ue

liner. Vent the stove into a masonry chimney or an approved, insulated solid-fuel stainless-steel chimney with as short and straight a length of 6” (152.4mm) diameter

to a masonry chimney must be by a metal or masonry

thimble cemented in place.

chimney connector as possible. Connection

TOWARD APPLIANCE

MALE END OF CONNECTOR OR CHIMNEY PIPE

FLUE GAS DIRECTION

58.1B

W415-1473 / A / 09.30.16

4.1.2 ADDING SECTIONS

dd chimney sections, according to the manufacturers installation instructions. The chimney must extend at

least, 3 feet (1m) above its point of contact with the roof and at least 24 inches (61cm) higher than any wall, roof, building or obstacle within 10 feet (3m) horizontally.

LESS THAN

10 FEET

(3m)

24” (61cm)

MIN

3 FT (1m)

MIN

3 FT (1m)

MIN

24” (61cm) MIN

10 FT (3m)

TO NEAREST

ROOFLINE

RIDGE

LESS THAN

10 FT (3m)

10 FEET

(3m)

OR MORE

3 FT (1m)

MIN

24” (61cm)

MIN

FLAT ROOF

WALL

59.1B

W415-1473 / A / 09.30.16

4.1.3 TYPICAL THROUGH THE CEILING

A. Move the stove into position with the ﬂ ue centered, midpoint between two

joists to prevent having to cut them. Use a plumb bob to line up the center.

B. Cut and frame an opening in the ceiling to provide a 2” (50.8mm) clearance

between the outside of the chimney and any combustible material. DO NOT

FILL THIS SPACE WITH ANY TYPE OF MATERIAL.

Nail headers between the joist for extra support.

Firestop spacers must be placed on the bottom of each framed opening in any ﬂ oor or ceiling that the chimney passes through.

HEADERS

If your chimney system is enclosed within the attic area, a rafter radiation shield is required.

C. Hold a plumb bob from the underside of

the roof to determine where the opening in

FIRESTOP SPACER UNDERSIDE OF JOIST

the roof should be. Cut and frame the roof opening to maintain proper 2” (50.8mm) clearances.

NOTE: The chimney must be supported at the ceiling or roof so that it’s weight does not rest on the appliance and must comply with it’s manufacturer’s instructions.

LISTED

CHIMNEY

SPECIFIED

CLEARANCE

MAINTAIN

2” (50.8mm)

CLEARANCE

LISTED CHIMNEY

TERMINAL

STORM

COLLAR

FLASHING

ROOF

INSULATION

CEILING

SUPPORT

TO STOVE

FLOOR

PROTECTOR

CHIMNEY

SUPPORT

CHIMNEY

CONNECTOR

COMBUSTIBLE

WALL

60.1B

W415-1473 / A / 09.30.16

FLOOR

PROTECTOR

CHIMNEY

CONNECTOR

COMBUSTIBLE

WALL

CLEARANCE

EAVE

RAFTER

CLEARANCE WITH FIRESTOP

CEILING JOIST

THIMBLE

4.1.4 TYPICAL THROUGH THE WALL

If possible, design the installation so that the connector does not pass through a combustible wall. If during

your installation you must pass through a combustible wall, check with your building inspector before you begin. Also check with the chimney connector manufacturer for any speciﬁ c requirements.

Consult with your dealer regarding special connection components available for use for wall pass-throughs. Use only parts that have been tested and listed for use in a wall pass-through.

COMBUSTIBLE OUTSIDE WALL

SECTION

LISTED

CHIMNEY

STOVE

THIMBLE

PIPE

WALL SPACER

FOR OUTSIDE

LISTED

CHIMNEY

2” (50.8mm)

CLEARANCE INSULATED

SUPPORT

WALL

“T” WALL

ROOF

COMBUSTIBLE

CHIMNEY

CONNECTOR

MAINTAIN 2”

(50.8mm) CLEARANCE

THROUGH EAVE

CEILING

TERMINAL

STORM

COLLAR

FLASHING

4.1.5 TYPICAL EXISTING MASONRY

You can also install your appliance using your existing masonry chimney. To do so, follow the guidelines below. Use a factory-built thimble, or construct your own brick thimble. If you are using a masonry chimney, it is important that it be built in compliance with the speciﬁ cations of the Building Code in your region. It must normally be lined with ﬁ re clay bricks, metal or clay tiles sealed together with ﬁ re cement. (Round ﬂ ues are the most efﬁ cient). The maximum ﬂ ue size is 8” (203.2mm) x 8” (203.2mm) square or 6” (152.4mm) round. For greater diameters it is necessary to install a 6” stainless steel liner.

FLOOR

PROTECTOR

COMBUSTIBLE

WALL

61.1A

62.1A

W415-1473 / A / 09.30.16

5.0 FINISHING

5.1 DOOR REMOVAL / INSTALLATION

A. Pivot the door open and lift up to

clear the bushings. Do not pivot the door any further than necessary.

B. Carefully set the door aside and

pull the pins out from the door bushings. Repeat in reverse order to install the door.

C. Install the door in reverse order.

5.2 DOOR HANDLE INSTALLATION

BURNING YOUR APPLIANCE WITH THE DOORS OPEN OR AJAR CREATES A FIRE HAZARD THAT

MAY RESULT IN A HOUSE AND OR CHIMNEY FIRE.

DO NOT STRIKE OR SLAM DOOR.

NEVER REMOVE THE DOOR WHEN THE APPLIANCE IS HOT.

WARNING

PINS

NOTE: DOOR MAY NOT BE AS

ILLUSTRATED

FRONT VIEW

DOOR

HANDLE

SPRING

WASHER

SPACER

DOOR HANDLE

LATCH

LOCK

NUT

NOTE: Position of door handle latch.

98.1

W415-1473 / A / 09.30.16

5.3 BRICKS AND BAFFLE INSTALLATION

WARNING

OPERATION OF THE APPLIANCE WITHOUT THE BAFFLES CAN RESULT IN EXCESSIVE

TEMPERATURES THAT COULD DAMAGE THE APPLIANCE, CHIMNEY AND THE SURROUNDING

ENCLOSURE.

With appliance and chimney installation completed, move the bricks into place for your appliance as illustrated.

A. Install the bottom bricks, working from the back of the appliance forward. B. Before installing the back bricks, loosen the screw holding the brick retainer and ensure that it has

been moved forward. Install the six bricks along the back wall by pivoting the bricks up under the brick retainer. Retighten the screw.

C. Referring to the appropriate illustration for your appliance, install the ﬁ rst two rows of side bricks

as shown. Pivot ﬁ bre bafﬂ e into place, with the brick retainer down and towards the outside of the appliance. Slide top row of bricks into place to support the bafﬂ e. Bafﬂ e must sit ﬂ at on outside row of bricks as well as the ﬂ ange on the manifold shield. Push bafﬂ e all the way to the rear of the ﬁ rebox, leaving a minimum of a 1" (25mm) gap along the front. This will allow ﬂ ue gases to escape the ﬁ rebox.

D. Install the 4 bricks along the front opening.

NOTE: Do not operate if bafﬂ e and manifold shield are not in position.

(All Firebricks are 1 1/4” (32mm) Thick)

FIREBRICK

DIMENSIONS

4 1/2” x 9” (114mm x 229mm) W090-0015 (X23)

PAR T #

FIREBRICK

DIMENSIONS

RS Notched Brick

4 1/2” x 9” (114mm x 229mm)

PAR T #

W090-0208 (X1)

3” x 9” (76mm x 229mm) W090-0166 (X4)

4 1/2” x 4 1/2” (114mm x 114mm) W090-0003 (X2)

3” x 9” (76mm x 229mm) W090-0002 (X2)

LS Notched Brick

4 1/2” x 9” (114mm x 229mm)

NOTE: BRICKS

E & F ARE

NOTCHED AT

REAR.

W090-0207 (X1)

2 1/4” x 9” (57mm x 229mm) W090-0018 (X1)

2 1/4” x 6 1/8” (57mm x 79mm) W090-0019 (X1)

4 1/2” x 2 1/2” (114mm x 64mm) W090-0016 (X1)

4 1/2” x 6 1/2" (114mm x 165mm)

Ash Plug

W510-0011 (X1)

BRICK

RETAINERS

(Fibre Bafﬂes)

W018-0130 X2

W415-1473 / A / 09.30.16

6.0 OPTIONAL KIT INSTALLATIONS

6.1 BLOWER KIT INSTALLATION

RISK OF FIRE AND ELECTRICAL SHOCK.

TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE.

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH

THIS APPLIANCE. USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS

COMPONENTS, VENTING COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL

ENSURE THAT THE FAN’S POWER CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE

APPLIANCE TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE. DO NOT RUN THE POWER

THE WIRE HARNESS PROVIDED IN THE BLOWER KIT IS A UNIVERSAL HARNESS. WHEN

INSTALLED, ENSURE THAT ANY EXCESS WIRE IS CONTAINED, PREVENTING IT FROM MAKING

Provisions have been made on the appliance to install an optional blower kit (EP65) that comes complete with a variable speed switch to turn the blower on and off, as well as adjusting the blower speed and a thermostatic sensor to thermally activate the blower.

Drywall dust will penetrate into the blower bearings, causing irreparable damage. Care must be taken to prevent drywall dust from coming into contact with the blower or its compartment. Any damage resulting from this condition is not covered by the warranty policy.

Use of the blower increases the output of heat.

TURN OFF THE ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE.

VOID THE WARRANTY AND CERTIFICATION.

CONTACT WITH MOVING OR HOT OBJECTS.

WARNING

CORD BENEATH THE APPLIANCE.

51.5

6.1.1 BLOWER INSTALLATION

A. Ensure the thermal disc bracket is in the correct position, refer to Figure 1. B. Remove the knock-out from the back of the appliance. C. Install the blower and housing as shown using the 4 screws supplied, refer to Figure 2. D. Loosen the thermal disc bracket (2 screws) and slide the bracket until the thermal disc is touching the

rear of the ﬁ rebox and secure.

Fig. 1

THERMAL DISC BRACKET

Fig. 2

KNOCKOUT

SCREWS

BLOWER

THERMAL DISC

BRACKET

W415-1473 / A / 09.30.16

7.0 OPERATION

WARNING

ALWAYS OPERATE THIS APPLIANCE WITH THE DOOR CLOSED AND LATCHED EXCEPT DURING START UP AND RE-FUELING. ALWAYS WEAR GLOVES TO PREVENT INJURY. DO NOT LEAVE THE

FIRE UNATTENDED WHEN THE DOOR IS UNLATCHED AS UNSTABLE WOOD COULD FALL OUT OF

THE FIRE CHAMBER CREATING A FIRE HAZARD TO YOUR HOME.

NEVER LEAVE CHILDREN UNATTENDED WHEN THERE IS A FIRE BURNING IN THE APPLIANCE.

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID,

OR SIMILAR LIQUIDS TO START OR ‘FRESHEN UP’ A FIRE IN THIS APPLIANCE. KEEP ALL SUCH

LIQUIDS WELL AWAY FROM THE APPLIANCE WHILE IT IS IN USE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE SHOULD BE KEPT A MINIMUM OF 4 feet

(1.2m) FROM THE FRONT FACE.

ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE

TESTING AUTHORITY IS CONSIDERED BREACHING CSA B365 (CANADA) AND ANSI NFPA 211 (USA).

OPEN AIR CONTROL (AND DAMPER WHEN FITTED) BEFORE OPENING FIRING DOOR.

HOT WHILE IN OPERATION, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY

CAUSE SKIN BURNS. WEAR GLOVES TO OPERATE YOUR APPLIANCE.

BURNING YOUR APPLIANCE WITH THE DOORS OPEN OR AJAR CREATES A FIRE HAZARD

THAT MAY RESULT IN A HOUSE AND OR CHIMNEY FIRE.

THIS WOOD APPLIANCE HAS A MANUFACTURER-SET MINIMUM LOW BURN RATE THAT MUST

NOT BE ALTERED. IT IS AGAINST FEDERAL REGULATIONS IN THE UNITED STATES TO ALTER THIS

SETTING OR OTHERWISE OPERATE THIS WOOD APPLIANCE IN A MANNER INCONSISTENT WITH

OPERATING INSTRUCTIONS IN THIS MANUAL.

Your Timberwolf EPA listed product is a Hi-tech appliance, designed with the most advanced technology. The appliance is extremely airtight. It has an exclusive direct outside air supply (optional kit), a safety feature

designed to prevent spillage, and to keep your house free of carbon monoxide, in case of a down drafting chimney or an internal negative pressure. This appliance requires periodic inspection and repair for proper

operation. It is against federal regulations in the United States to operate this appliance in a manner inconsistent with operating instructions in this manual.

The ﬁ rst ﬁ re(s) in your appliance will be difﬁ cult to get going and keep going with little amount of heat being generated. This is a result of the moisture being driven out of the ﬁ re brick. During the break-in period (the ﬁ rst 2 or 3 ﬁ res) create only small, ﬁ res using kindling; this will allow the ﬁ rebrick to cure. Do not be alarmed if small hairline cracks develop in the ﬁ rebrick. This is a normal occurrence and does not pose a safety hazard. The paint may also smell a little for the ﬁ rst few ﬁ res as it cures and you may wish to open a door or window to alleviate the smell.

To start, a brisk ﬁ re is required. Place loosely crumpled paper on the ﬂ oor of the appliance and cover with dry kindling. Open the air control fully by sliding control all the way to the right. Light the paper and leave the door slightly ajar (one inch) until all kindling is burning. To maintain a brisk ﬁ re, a hot coal bed must be established and maintained.

During the refueling and rekindling of a cool ﬁ re, or a ﬁ re that has been burned down to the charcoal phase, operate the appliance at a medium to high ﬁ ring rate for about 10 minutes to ensure the temperature reaches 600°F (315°C)

Slowly add larger wood (2x4 size pieces). Lay the pieces lengthwise from side to side in the hot coal bed with a shallow trench between, so that the primary air can ﬂ ow directly into this trench and ignite the fuel above. When the ﬁ re seems to be at its peak, medium sized logs may be added. Once these logs have caught ﬁ re, carefully close the door. (Closing the door too quickly after refueling will reduce the ﬁ rebox temperature and result in an unsatisfactory burn.) Remember it is more efﬁ cient to burn medium sized wood, briskly, and refuel frequently than to load the appliance with large logs that result in a smouldering, inefﬁ cient ﬁ re and dirty glass.

W415-1473 / A / 09.30.16

As soon as the door is closed, you will observe a change in the ﬂ ame pattern. The ﬂ ames will get smaller and lazier because less oxygen is getting into the combustion chamber. The ﬂ ames, however, are more efﬁ cient. The ﬂ ames will remain lazy but become larger again as soon as the ﬁ rebricks have been heated thoroughly and the chimney becomes heated and provides a good draft. At this point, the roaring ﬁ re that you see when the door is opened is wastefully drawing heated room air up the chimney, certainly not desirable. Always operate with the door fully closed once the medium sized logs have caught ﬁ re.

You can now add larger pieces of wood and operate the appliance normally. Once the appliance is entirely hot, it will burn very efﬁ ciently with little smoke from the chimney. There will be a bed of orange coals in the ﬁ rebox and secondary ﬂ ames ﬂ ickering just below the top bafﬂ es. You can safely ﬁ ll the ﬁ rebox with wood to the top of the door and will get best burns if you keep the appliance pipe temperatures between 250°F (120°C) and 450°F (270°C). A surface thermometer will help regulate this.

Without a appliance thermometer, you are working blindly and have no idea of how the appliance is operating! An appliance thermometer offers a guide to performance and should be located 18" (457mm) above the ﬂ ue collar. Install the thermometer according to manufacturers instructions.

Can’t get the ﬁ re going?

Use more kindling and paper. Assuming the chimney and vent are sized correctly and there is sufﬁ cient combustion air, the lack of sufﬁ ciently dry quantities of small kindling is the problem. Thumb size is a good gauge for small kindling diameter.

Can’t get heat out of the appliance?

One of two things may have happened. The appliance door may have been closed prematurely and the appliance itself has not reached optimum temperature. Reopen the door and/or draft control to re-establish a brisk ﬁ re. The other problem may have been wet wood. The typical symptom is sizzling wood and moisture being driven from the wood.

7.1 OPTIMUM BURN METHOD

For optimal emissions performance and efﬁ ciency follow these simple guidelines when using your appliance:

A. Maintain a 2" (51mm) deep, hot, glowing red coal bed. B. Burn dry seasoned wood with less than 20% moisture content and burn so that the glass door

remains clean.

C. A stove thermometer 18" (457mm) up on the single wall stove pipe should indicate 350°F (176°C) as

an average temperature.

D. Maintain a minimal trace of smoke coming from the chimney when the appliance is burning as

intended.

E. Inspect and replace all necessary components such as gaskets, manifolds, glass and other

components which may affect the overall appliance performance.

F. Ensure an adequate draft to control burn rate and temperature.

Refer to “OPERATION” and “MAINTENANCE” sections for detailed information.

W415-1473 / A / 09.30.16

7.2 AIR CONTROL

THIS WOOD APPLIANCE HAS A MANUFACTURER-SET MINIMUM LOW BURN RATE AND MAXIMUM

HIGH BURN RATE THAT MUST NOT BE ALTERED. IT IS AGAINST FEDERAL REGULATIONS IN THE

UNITED STATES TO ALTER THIS SETTING OR OTHERWISE OPERATE THIS WOOD APPLIANCE IN A

Draft is the force which moves air from the ﬁ rebox up through the chimney. The amount of draft in your chimney depends on the length and diameter of chimney, local geography, nearby obstructions and other factors including the amount of heat generated by the ﬁ re which can be measured by an appliance thermometer.

Adjusting the air control regulates the temperature. The draft can be adjusted from a low burn rate with the handle in fully, to a high rate with the handle fully out.

Inadequate draft may cause back-pufﬁ ng into the room through the appliance and chimney connector points and may cause plugging of the chimney. Too much draft may cause an excessive temperature in the appliance, glowing red appliance parts or chimney connectors or an uncontrollable burn which can lead to a chimney ﬁ re or permanent damage to the appliance.

Do not operate your appliance for longer than 30 minutes with the draft control on “HIGH” (fully open).

WARNING

MANNER INCONSISTENT WITH OPERATING INSTRUCTIONS IN THIS MANUAL.

ASH LIP

7.3 FIRE EXTINGUISHERS / SMOKE & CARBON MONOXIDE DETECTORS

NOTE: Always check your smoke and CO detectors are working properly.

All homes with a solid fuel burning appliance should have at least one ﬁ re extinguisher in a central location, known to all and at least one smoke detector and carbon monoxide (CO) detector in the room containing the appliance. If the smoke detector sounds an alarm, correct the cause but do not de-activate or relocate the smoke detector. If the carbon monoxide detector sounds an alarm, immediately vent the area, evacuate and call your local ﬁ re department.

91.1A

W415-1473 / A / 09.30.16

+ 50 hidden pages