NAPCO MAGNUM ALERT 1008e, MAGNUM ALERT 1008eM Installation Instructions Manual

Download

Page 1



INSTALLATION

Publicly traded on NASDAQ Symbol: NSSC

INSTRUCTIONS

MAGNUM ALERT 1008e / 1008eM

CONTROL PANEL / COMMUNICATOR

MAGNUM ALERT

COMPUTERIZED SECURITY SYSTEM

MA1008e: Household Fire & Burglary Warning System Control Unit

MA1008eM: Commercial Burglar Alarm System Control Unit

See page 10 for a summary of changes from the previous edition

L NAPCO Security Systems

1000 SERIES

UL / cUL Listed

WI587E 8/07

MA1008e / 1008eM Installation Instructions

Page 2



TABLE OF CONTENTS

Section Page

1. INTRODUCTION ......................................................................................................3

GENERAL DESCRIPTION .......................................................................................3

FEATURES ...............................................................................................................3

SPECIFICATIONS ....................................................................................................4

ORDERING INFORMATION .....................................................................................4

UL/CUL LISTINGS ....................................................................................................4

COMPATIBLE UL-LISTED DEVICES ......................................................................4

SUMMARY OF UL REQUIREMENTS ......................................................................5

2. INSTALLATION .......................................................................................................6

CONTROL-PANEL MOUNTING ...............................................................................6

KEYPAD MOUNTING ..............................................................................................6

WIRING TO A MERCANTILE BELL ..........................................................................7

TYPICAL FIRE INSTALLATION ..............................................................................7

3. GETTING UP AND RUNNING ..................................................................................8

POWER-UP SEQUENCE .........................................................................................8

DEFAULT PROGRAM ..............................................................................................8

CENTRAL STATION REPORTING ...........................................................................8

USER KEYPAD PROGRAMMING ...........................................................................8

KEYPAD OPERATION .............................................................................................9

TESTING THE SYSTEM ..........................................................................................10

CHANGES FROM PREVIOUS EDITION ..................................................................10

4. PROGRAMMING ...................................................................................................... 11

KEYPAD PROGRAMMING .......................................................................................11

PROGRAMMING SHEETS .......................................................................................12

DOWNLOADING FROM A COMPUTER .................................................................13

PROM PROGRAMMING ..........................................................................................13

5. GLOSSARY & PROGRAMMING DATA ...................................................................17

6. WIRING DIAGRAM ..................................................................................................31

MA1008e / 1008eM Installation Instructions

Index starts on page 28

NAPCO Security Systems, Inc.

333 Bayview Avenue, Amityville, New York 11701

For Sales and Repairs, call toll free: (800) 645-9445

For direct line to Technical Service, call toll free: (800) 645-9440

Internet: http://www.napcosecurity.com

L NAPCO Security Systems

Page 3

1. INTRODUCTION

Page 3



GENERAL DESCRIPTION

The MAGNUM ALERT-1008e and MA1008eM are microcomputer-based eight-zone control panels with provisions for Ambush, three Keypad Panics (Fire, Police and Auxiliary), a supervised Fire Zone and a variety of reporting features. An event log, accessible only through Napco PCD2000 Quickloader software, monitors up to 82 prior events. The MA1008eM "Mercantile" version is supplied with a heavyduty enclosure for increased tamper resistance and a tamper switch for tamper protection. (Note: Do not use Fire Zones in a Mercantile Installation).

The system is contained within a wall-mounted enclosure and Includes an integral digital communicator and a power transformer.

The keypad allows the user to:

• arm and disarm the system

• check the status of each zone

• check which zones were violated after an alarm

• selectively bypass one or more zones

• display bypassed zones

• cancel entry delay

• send a Panic or Ambush alarm

• enter or change arm/disarm codes

• test the audible alarm and backup battery

• test each zone for problems (Fault Find)

• test the telephone line while disarmed

• reset AC-Failure indication

• bypass a Priority Zone with Bypass

• turn the Chime feature on/off

• program zone features and communicator information

Four LEDs, a display and a sounder an the keypad provide visual and audible system and individual zone status Information. Most keys have secondary functions that are accessed by holding down the key until the sounder beeps, and are therefore termed "hold-down" functions. The following holddown functions are provided:

Key [1]: Alarm Test

Key [2]: Display Bypassed Zones

Key [3]: Display Status

Key [4]: Instant Alarm (cancels entry delay)

Key [5]: Chime on/off

Key [6]: Communicator Confidence Test or Manual

Download (see text) Key [7]: Fault Find Key [8]: Program Key [9]: Reset (System-trouble indication; Failure-to-

Communicate sounder; Day Zone Indication; Alarm-

Memory display; Fire Zone; Fault-Find mode; Bypass

Priority-with-Bypass; and Power-Up Delay) Key [B]: Alarm History (indicates last alarmed zone

(s))

The panels may be programmed in a variety of ways: (a)

from the keypad, in its secondary Dealer-Program Mode of operation; (b) from a PROM (programmable read-only memory), which is itself programmed on an accessory programmer; or (c) from an IBM PC-compatible computer using

Napco's PCD-Windows Quickloader Download Software.

Designed for use with the PCI2000 Computer Interface Kit, the MA1008e includes a modem to permit remote downloading/uploading over telephone lines or local downloading using a PCL2000 Local Download Cable.

FEATURES Protection Zones

• Seven end-of-line-resistor supervised zones.

• Two separately-programmable entry delays for Exit/

Entry Zones.

• Burglary Zone options include:

- Priority or Priority with Bypass

- Selective or Group Bypassing

- 24-Hour Protection

- Day Zone Supervision

- Auto Reset

- Exit/Entry Delay 1; Exit/Entry Delay 2

- Preprogrammed Auto Bypass (removable)

- Optional 50mS or 7mS Loop Response (normally 750mS)

- Programmable Abort Delay

- Fire on Burglary Zone

• Separate supervised Fire Zone

• Three keypad panics

Alarm Outputs

• Timed Burglary (sweep siren) and Fire (steady siren)

Output: Programmable by zone and time

• Timed Fire Output: Fixed to dedicated and programmed

Fire Zones, programmable for time

• Pulsing Steady Siren Output: Fixed to dedicated and

programmed Fire Zones, programmable for time

• NTO (No Timed Output) Lug

• Optional voltage on alarm

Keypad Functions

• Keypad permits:

- Arm/Disarm Code Selection of up to 8 user codes, up to 4 digits each

- Digital Code Entry to arm and disarm system

- Selective and Group Bypass Selection

- Panic Zone Activation

- Ambush Activation

- Hold-Down Function Access

- Resetting of various functions and conditions

- Programming zone features and communicator options

• LED display:

- Alarm State (armed/disarmed) (ARMED/ALARM)

- Zone Status (STATUS) - one or more zones in trouble

- Zones Bypassed - one or more zones removed

- Fire Zone Status (FIRE/TROUBLE)

- System troubles

• Display Indicates:

- Zone(s) in alarm and alarm history

- Zone(s) in trouble

- Zone(s) bypassed

- System troubles

- Programmed data entries (Dealer Program Mode)

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 4



Page 4

• Sounder signals:

- Entry Delay in Progress

- Hold-Down Function Accessed

- Entry Door Opened while Disarmed (Chime)

- System Armed with a Zone in Trouble

- Day Zone in Trouble

- Fire Zone Alarm/Trouble

- Central-Station Ringback

- Failure-to-Communicate system trouble

- Exiting Dealer Program Mode

Communicator Features

• Integral digital communicator with true dial tone detec-

tion, double-pole line seizure and anti-jam

• Programmable abort delay time

• Rotary or Touch-Tone

available as backup to unsuccessful Touch-Tone ing

dialing available. Rotary dialing

• Two telephone numbers and receiver/data formats can

be accessed

• Two-digit event codes and 4-digit subscriber codes pro-

grammable for those receivers accepting these formats

• Central-Station Ringback on closing or Auxiliary panic

Reporting Features

• Report on Alarm

• Opening and/or Closing Reporting by Individual User

• Opening Report After Alarm

• Day Zone Trouble; Fire Zone Trouble

• Ambush; Panic; Keypad Auxiliary Panic

• Test Timer; Reset Test Timer on Report

• AC Failure; Low-Battery Report

• Force-Arm Report; Force-Arm/Status Report .

• Control-Panel Restore Report; Zone-Restore Report

• Backup Reporting; Double Reporting; Split Reporting

Other Features

• Supports NAPCO's Super Spectrum's Wireless System

• Audible Bell-Test on Arming

• Power-Up in Last State

• Programmable Chime Duration

• Chine/Display Chime Mode

• No End-of Line Resistor

• Watch Mode

• Sensor Watch™

• 2- or 4-Wire Smoke Detector Compatibility on dedicated

Fire Zone

• Electronic Dealer lockout prevents unauthorized access

SPECIFICATIONS

Operating Temperature: 0-49 °C (32-120 °F) Input Power: 16VAC, Class 2 step-down transformer TRF12

(19.2VA) or TRF11* (40VA) Loop Voltage: 10-13 VDC Loop Current: 2.8mA (normal resistance) Loop Resistance: 300Ω maximum series resistance Alarm Output (Burg/Fire): Commercial, 12-12.5VDC, 1.2A

maximum; Residential, 10.9-12.5VDC, 125mA max. (Dry) Contact Ratings: 24VDC, 2A (resistive)

dial-

Auxiliary Output: Commercial, 12VDC regulated; Residen-

tial, 10.6-12.5VDC

Combined Standby Current: (Remote Power + Aux. Output

+ Relay Output) 450mA maximum with standard TRF12;

500mA maximum with optional TRF11 Remote Station, Current: 35mA typical Maximum Number: 5 Recommended Battery: Rechargeable, sealed-acid,

(12VDC, 4AH) or (12VDC, 7AH) Standby Time: See Wiring Diagram Fuses, Burglary/Fire Output: 3A, 1AG (F2) Remote Power: 1A, 1AG (F3) Battery: 3A, Over Current Protection Housing Dimensions: MA1008e, 12.6 x 14.1 x 3.6" (32 x 36

x 9.1cm) HxWxD; MA1008eM, 13.3 x 13.3 x 3.8" (33.8 x

33.8 x 9.7cm) (HxWxD)

Shipping Weight: MA1008e, Approx. 14lb. (6.4kg);

MA1008eM, Approx. 11lb. (5.0kg) *The TRF11 (40VA) Transformer and RBAT6 (7AH) Battery

are required for Mercantile installations.

ORDERING INFORMATION Equipment Supplied

MA1008e - Residential 8 -zone (7 Burglary; 1 Fire; 3 Key-

pad Panics) 12-volt alarm control panel with integral com-

municator and siren driver, RP1054e keypad, 4AH and

TRF12 power transformer. MA1008eM--As above, but for Mercantile installations. Less

keypad and battery, but with heavy-duty enclosure, Tam-

per Switch and TRF11 40VA power transformer.

Optional Peripherals and Accessories

RP1054e Designer-Style 4-Wire Keypad RP1000eLCD Designer-Style Keypad with LCD display RBAT-H1* Dual Battery Harness (not for UL installations) TRF11 Transformer, 16VAC 40VA, Class 2 (UL Listed) TRF12 Transformer, 16VAC, 19.2VA, Class 2 (UL Listed) EOL2.2K End-of-Line Resistor Assembly, 2.2kΩ. FT2200 End-of-Line Relay/Resistor Supervisory Module PS3002 Power-Supply Module MAV-15 Two-Way Voice/Listen In Module GSM-400 Ground Start Module LOCK-8 Lock & Key Set PCI2000 Quickloader Interface and Software PCL2000 Quickloader Local Download Cable WL1 Wire with Lug Connector, 20" *UL Listed Accessory

UL/cUL LISTINGS

Household Fire and Burglary Warning System Control Unit. Combination Fire and Burglary (see Compatible UL Listed Devices), Commercial Burglary (MA1008eM)

COMPATIBLE UL-LISTED DEVICES (See Note below)

For Residential control panels:

Smoke Detectors:

4-Wire:

System Sensor 1812, 2812TH, 1851B, 2851B, 2851BTH,

each with B102 Base

ESL 445AT*, 445C, 445CT, 445CR, 445CRT

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 5



Gentex 812, 812T, 812P, 812PT, 812PH, 8120, 8120T,

8120P, 8120PT, 8120PH

Hochiki SLG with YBC-RL4-RA Base

2-Wire

System Sensor 1400*, 2400*, 2400TH*, each with B101B

Base; 1451*, 2451*, 2451TH*, each with B401B Base

Subtract total smoke-detector alarm current from a available

standby current.

Horn:

Wheelock 34T-12R* (Rated at 85dB for indoor household

applications)

*Note: Devices not identified with an asterisk (*) require optional power supply PS3002 for UL installations. Compatibility of detectors without "*" has not been evaluated by UL.

For Mercantile control panels (MA1008eM)

Bells:

Ademco AD8-12, AD10-12

Amseco MBL-8/12V, -10/12V

Mercantile Bell:

Ademco AB-12, Bell in Box

Speakers:

Ademco 713

Atlas Sound VT-158U

SUMMARY OF UL REQUIREMENTS

Note: The MA1008e may not be used for fire protection

where prohibited by local codes. The MA1008eM may not be used for fire protection in any installation.

Residential

The following summarizes UL programming and wiring requirements for Residential Household Fire and Burglary installations.

• Recognized Limited-Energy Cable for initiating, indicat-

ing and supplementary circuits;

• Initiating loops supervised if longer than 3 feet;

• FT2200 End-of-Line Relay for Fire (if using 4-wire smoke

detectors);

• Minimum alarm timeout of 4 minutes;

• Maximum exit time: 60 seconds; maximum entry time:

45 seconds;

• Do not program Don't Wait for Handshake, Telco 1 & 2;

Swinger Shutdown; Force Arming; Group Bypass; 7mS

or 50mS Loop Response. Abort Delay may not exceed 45 seconds.

• Program Disable Callback Download; Disable Function

6 Download;

• Key Input on Zone 7 feature may not be enabled;

• Automatic dialer may not dial a police-station number

that has not been dedicated for such service;

• System must be tested at least weekly under AC battery

and battery-only conditions;

• Replace the rechargeable battery at least every 5 years;

• If the battery is heavily discharged, replace it or have it

tested by a qualified technician;

• Remote panic switches must be located in the same

room as the control unit and keypad. Wiring may not

pass through any barrier;

• For silent panic, connect only to UL-Listed holdup de-

vices. In California: CFM-Ilsted for residential use (Listing No. 7165-992:111).

Mercantile

The following summarizes UL programming and wiring

requirements for Mercantile installations.

• TRF11 (40VA) and RBAT6 (7AH) are required;

• Heavy-duty enclosure with door tamper (MA1008eM) is

required;

• Digital communicator must be utilized for Low Battery

reporting, but not Low Battery restore;

• Program Audible Test on Arming; Force-Arm Code; a

maximum exit delay of 10 seconds; Disable Display By-

pass; Auto-Reset;

• Do not use Fire Zones;

• Ademco AB12 Bell & Box is required.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 6



2. INSTALLATION

CONTROL-PANEL MOUNTING

Choose a mounting location accessible to (a) a continuously-powered AC source, (b) a cold-water-pipe ground ideally no further away than 10 feet, and (c) telephone lines (keep telephone wiring away from speaker wires). Remove appropriate knockouts for cables. Place the control panel at a convenient viewing height and mark the mounting holes.

A keypad should be located near the exit/entry door. Up to 5 keypads may be connected if the longest cable run from the panel to the farthest keypad, whether daisy chained or home-run wired, is less than 1800 feet. See Combined Standby Current specifications. Each keypad typically draws 35mA, however do not use more than 5 keypads.

The control panel door is secured shut by 3 screws (supplied). A lock and keyset are available as an option (see ORDERING INFORMATION).

Grounding

Connect the mounting screw at the lower-left corner of the circuit board (EARTH GROUND) to a metal cold water pipe. Do not use a gas pipe, plastic pipe or AC ground connections. Use at least 16-gauge wire. Make the run as short and direct as possible. Avoid sharp bends in the wire.

Tamper Switches

Tamper switches may be installed to prevent opening of the enclosure door or removal of the cabinet from the wall. Ideally, tamper switches should be connected to a zone that is active at all times, thus it may be necessary to program that zone for 24-Hour Protection. When used on a normally-open zone, normally-closed tamper switches (open when set) should be wired in parallel. On a normally-closed zone, install Napco normally-open tamper switches (closed when set) in series. There are two tamper switch provisions in the cabinet:

1. To prevent cabinet removal from the wall, there are three mounting holes on the left side of the cabinet; another hole on the back that allows the switch button to contact the wall.

2. To prevent opening the cabinet door, there are three mounting holes on the right side of the cabinet. When mounted, the tamper-switch button should contact the inside of the door. Be sure to alert the user that opening the enclosure door will cause a tamper alarm.

KEYPAD MOUNTING (Keypad model RP1054e)

Opening the keypad. There are two slats along the bot-

tom edge of the keypad about 1 inch from each side. To open, insert a medium screwdriver into either slot and push up with a slight twisting motion to release the retainer tab. Repeat for the other slot. Pull out at the bottom and lift off the two hooks at the top.

This keypad features a handy pull-up reference label. Before mounting the keypad onto the wall, push the Sliding Label Plate (with label and felt backing affixed and handle facing forward) down the guides at the rear of the keypad until it snaps into place. Once installed, the Sliding Label Plate cannot be removed without first removing the keypad from the wall.

When installing the rear case, be sure that the words "TOP" and "UP" (molded into the case) are properly oriented.

The rear case is provided with a variety of holes to accommodate virtually any mounting situation. The four angled elongated holes are for mounting directly into a wall using appropriate screws; these holes will allow leveling adjustment. If installing into a double-gang box, insert mounting screws through the two vertical elongated holes on the left side of the case and into the box. If the box is visible when viewed from the front, adjust the keypad vertically, then tighten the screws. Then, using hardware suitable far the mounting surface, add one or two screws at the right side of the keypad case directly into the wall to ensure a secure installation.

Keypad Wiring (Also see Wiring Diagram)

Connections to the keypad are summarized in the following

table. Avoid routing keypad wiring close to zone wiring.

Note: If using a soldering iron, avoid splashing solder onto

keypad circuit board or components.

Keypad Wire Color Control Panel Terminal

Yellow 9 (Clock)

Green 10 (I/O)

Red 7 (+)

Black 8 (-)

White*

Table 1. Keypad Wiring.

to N/O momentary contact

pushbutton switch(es)

*Wire additional Panic Switches in parallel. Insulate both

white wires if not used (a short will cause a panic alarm).

Remote Panic. To connect a remote (Police) panic but-

ton, splice the two white keypad wires to a normally-open momentary-contact pushbutton switch. Similarly, additional panic buttons may be wired in parallel with the first, as needed. If remote panic will not be used, insulate both white wires, as a short across them will cause a panic alarm. Note that in UL installations, remote panic buttons must be located in the same room as the keypad, with no intervening barriers.

Backlighting. Keypad backlighting requires no additional

wiring. In normal use, the keypad is always dimly backlit. To reduce or disable backlighting, see Keypad Jumper Options, which follows.

Keypad Jumper Options

Several white jumpers provide a variety of options. Viewing the keypad from the front, these jumpers are conveniently located at the top edge (Jumper D) and along the right side edge (top to bottom: Jumpers C, B, A and E) for easy access.

Disable Keypad Panic. Cut Jumper A to disable all three keypad panic features. (Cutting Jumper A does not disable the two white remote-panic wires).

Disable Keypad Sounder. Cut Jumper B to completely disable the sounder.

Disable Touchpad Backlight. Cut Jumper C to disable touchpad backlighting.

Reduce Touchpad Backlight. Cut Jumper D to reduce backlight intensity.

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 7



Activate Fire & Aux. Panics. Cut Jumper E to enable F/

P/A keypad panics. Note: This jumper must be cut to utilize the three-keypad-panic feature of the MA1088e. Conversely, if the jumper is cut, Enable Keypad Fire Panic or Enable Key- pad Auxiliary Panic must be programmed or adverse operation will result.

Assembling the Keypad. To reassemble the keypad af-

ter installation, hang the top of the front panel onto the hooks in the rear case and push in firmly at the bottom until the retainer tabs snap into place. (If difficulty is encountered, push the retainer tabs up lightly using a screwdriver, as when removing).

WIRING TO A MERCANTILE BELL

Refer to Fig. 1. Use an zone for a Tamper Zone and program it for 24-Hour Protection. The Tamper Zone will supervise the cold-water pipe ground, door tamper and bell box. UL installations require a tamper switch on the control panel door. For this purpose, use the normally closed (when set) tamper switch supplied with the MA1008eM in series with the Tamper Zone.

GROUND

SUPERVISION

WIRE

COLD-WATER-GROUND PIPE

WITH GROU ND CLAMPS MORE

SPLICE

THAN 1/4" APART.

4700-OHM

END-OF-LINE

RESISTOR

TAMPER

EARTH GRO UND

NAPCO MA1008eM

TAMPER

ZONE

DOOR

― BELL +

REQUIRE RIGID CONDUIT

OR ELECTRICAL METALLIC

UL INSTALLATIONS

TUBING (EM T) FOR

ENTIRE LENGTH.

INTERNAL BELL

4700-OHM

END-OF-LINE

RESISTOR

TAMPER

SWITCHES

― BELL +

ADEMCO AB-12

BELL IN BOX

Fig. 1. Wiring to a Mercantile Bell.

TYPICAL FIRE INSTALLATION (Where permitted by local

codes; not for use in Mercantile Installations).

LIVING ROOM

BASEMENT

CONTROL CENTER; FIRE ALARM SOUNDING DEVICE;

KEYPAD; SMOKE DETECTOR; HEAT DETECTOR

ATTIC

BEDROOM

S T

Fig. 2. Typical Fire Installation.

HALL

RECREATION

ROOM

ATTIC

BEDROOM

KITCHEN

ATTIC

GARAGE

At least one smoke detector should be installed directly outside each sleeping area. If there is more than one floor, additional smoke detectors should be installed on each level, including the basement. The living-area and basement smoke detectors should be installed near the stairway of the next upper level.

For increased protection, additional detectors should be installed in areas other than those required, such as dining rooms, individual bedrooms, furnace rooms, utility rooms and hallways. Heat detectors, rather than smoke detectors, are recommended in garages, attics, and kitchens due to conditions that may result in false alarms and improper operation. Large areas and areas with partitions, ceiling beams, doorways, and open joists will require additional detectors. Refer to NFPA Standard 74 (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269) for additional information, including proper mounting methods.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 8



3. GETTING UP AND RUNNING

POWER-UP SEQUENCE

1. Referring to the Wiring Diagram, (a) connect the keypad to the four keypad terminals 7 through 10 and (b) Install endof-line resistors (color code red/red/red) across each zone.

2. Connect an earth ground (cold-water pipe) to the left screw that secures the circuit board to the cross rail.

3. Connect the power transformer to the AC Terminals 1 and 2 and plug the transformer into AC power.

4. Install the standby battery.

5. Check that the green STATUS LED on the keypad is lit.

6. Install loop wiring to zone terminals and relocate resistors to end of loops. Recheck green STATUS LED.

7. If reporting to a central station, connect a telephone connecting cord to the TELCO terminals: green to 23; red to 24; and PHONE terminals: brown to 25; gray to 26. Then see CENTRAL-STATION REPORTING.

DEFAULT PROGRAM

The MA1008e will function as a local alarm control panel right out of the box! The following default program is entered at the factory. It is the installer's responsibility to add, change and/or delete features in accordance with these instructions to customize the system to the user's requirements and to conform to local codes.

• Arm/Disarm Code: 1,2,3 (User 1)

• User Program Code: 1,2,3,4,5,6

• Dealer Program Code: 4,5,6,7,8,9

• Exit/Entry (Entry Delay 1): Zone 1

• Entry Delay 1: 30 seconds

• Entry Delay 2: 30 seconds

• Exit Delay: 45 seconds

• Priority: Zones 1-7

• Selective Bypass: Zones 1-7

• 24-Hour Protection: Keypad Panic

• Auto Reset: Zones 1-7; Keypad Panic

• Swinger Shutdown: Zones 1-7; Keypad Panic

• Chime: Zone 1

• Chime Time: 2 seconds

• Burglary Output: Zones 1-7; Keypad Panic

• Burglary Timeout: 15 minutes

• Fire Timeout: 15 minutes

• Download with Answering Machine enabled

• Auto-Reset After Alarm Timeout enabled

• Power-Up In Last State enabled

• Pulsing Fire Output enabled

• Reset Fire enabled

• Keypad Tactile Beep enabled

• Keypad Panic enabled

• Communicator-Confidence Test enabled

• Alarm/Trouble Codes,

- Zones 1-7: 31-37

- Panic: 21

- Fire: 11

- Ambush: 22

- Fire Trouble: F1

- No AC: F9

- Low Battery: F8

• Restore Codes,

- Zones 1-7: E1-E7

- Fire: E1

- Fire Trouble: EF

- No AC: E9

- Low Battery: E8

• Closing Codes, Users 1-4: C1-C4

• Opening Codes, Users 1-4: B1--B4

• Force-Arm Code: F

CENTRAL STATION REPORTING

The following additional programming is required for central

station reporting.

• Report on Alarm

• Subscriber ID (Account) Numbers, Groups 1 & 2*

• Receiver Format*

• Data Format*

• Telephone Number*

*Obtained from central station.

Note: Remember, for optimum security, the following code must also be reprogrammed:

• User-1 Code (see Programming User Codes, below).

For other programming, see Dealer Keypad Programming (Section 4) and the programming aid shown in Fig.

USER KEYPAD PROGRAMMING Programming User Codes

Note: The User Program Mode is disabled for the first

three minutes after power-up to allow you to use the Dealer Program Code. To cancel the delay, hold down Key [9].

Up to eight different Arm/Disarm Codes may be entered into the control panel using the keypad. User Code 5 may be programmed as a Service Code, a special user code intended for temporary or occasional use only (see Service Code).

To program a User Code:

1. Hold down Key [8] until the sounder beeps, then enter the User Program Code. (The default User Program Code is 1,2,3,4,5,6, but this code must be reprogrammed). When the User Program Code has been entered, the first three LED's on the keypad will flash and the sounder will beep rapidly, indicating the User Program Mode.

2. Now enter up to eight codes using any combination of up to four digits (digits 1-9 only).

Examples: Press:

[B], [1], then any 4 digits = User 1's code* [B], [5], then any 4 digits = User 5's code** [B], [8], then any 4 digits = User 3's code

*Default User-1 Code 1,2,3 must be changed. **May be programmed as Service Code or Arm-Only

Code.

3. To exit User Program Mode, press [B] twice.

The numbers selected are the only codes recognized by the system. Each user should be assigned his own dissimilar code and cautioned against divulging that code to anyone else Thus, should it became necessary to remove a user from the

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 9



system, that one code may be voided without affecting other codes, and that user would then be prevented from entry.

Service Code

The Service Code, if programmed, provides reduced access to the control panel for those with limited authority. Operation is similar to that of a regular Arm/Disarm Code, except that the Service Code is disabled at times. When active, it may be used to arm or disarm as many times as necessary. See User 5 Service Code in the Glossary.

The Service Code is controlled by User 1 . Whenever User 1 arms using his code, the Service Code is deactivated. To activate, merely arm using the Service Code. The Service Code can always be used to arm.

Changing or Voiding a Code

To change any User's Code, refer to Programming User Codes and simply change the 4-digit combination. Thus, to

change User 3's code, for example:

1. Hold down Key [8] until the function beep sounds.

2. Enter the User Program Code.

3. Press [B], [3], then 4 new digits = User 3's new code.

4. Press [B] twice to exit User Program Mode.

Similarly, User 3's code may be voided by not entering a 4digit combination. Thus, to void User 3's code:

1. Hold down Key [8] until the function beep sounds.

2. Enter the User Program Code.

3. Press [B], then [3] = User 3's code erased.

4. Press [B] twice to exit User Program Mode.

KEYPAD OPERATION Arming & Disarming the System

When a User Code is entered into the keypad, the red ARMED / ALARM LED will either turn on, indicating that the panel is armed; or turn off, indicating that the panel is disarmed. A "P" on the display with a steady sounder indicates an attempt to arm with (a) a system trouble (hold down [9] to reset keypad and arm), or (b) a Priority Zone in trouble (reenter code, then secure or bypass zone). If a wrong code is entered, the system will fail to respond. Wait at least 2 seconds before attempting to re-enter a code.

Alarm Reset

Disarm the panel to silence a sounding device.

Ambush Zone

The Ambush Zone is tripped by entering the Ambush Code just prior to disarming. Thus, should a user be forced to disarm by an assailant, the user can silently signal an emergency while appearing to be merely disarming the system. The Arm/ Disarm Code must be entered less than 10 seconds after the Ambush Code for an ambush report to be transmitted.

Keypad Panic

If using an F/P/A-Panic keypad, three keypad panics are available: Fire, Police and Auxiliary (cut keypad jumper to enable panics). If enabled, each is tripped by simultaneously pressing the following pairs of panic buttons:

• Fire Panic: press Keys [9/F] and [#]

• Police Panic: press Keys [*/P] and [#]

• Auxiliary Panic: press Keys [B/A] and [#]

Police Panic may be programmed to send a silent alarm to a central station, activate an audible alarm, or both. Note that the key pairs must be pressed at the same time to activate panic. See Panic Zone In the Glossary; also see Section 2: Keypad Jumper Options.

Bell / Battery Test (Hold-Down Function 1)

The terminal voltage of the battery is constantly monitored by the control panel. Hold-Down Function 1 provides a manual dynamic test by briefly sounding the bell directly from the battery.

A weak or defective battery is indicated by the display of a System Trouble "2". The system trouble display will be cleared and a restore reported when (a) the battery terminal voltage has returned to its specified restored level and (b) the condition has been detected by either the subsequent 24-hour dynamic test, a manual bell / battery test (Hold Down Function

1) or a manual reset (Hold-Down [9]).

To test the battery with a pre-existing low battery displayed, hold down Key [9] to temporarily reset the keypad, then hold down Key [1] to check bell operation from the battery. If the low-battery display returns the next time the system is disarmed, the battery is still weak and may require replacement. (Allow at least 4 hours for the battery to recharge). Also see System Trouble 2: Low Battery.

Communicator-Confidence Test (Hold-Down Function 6)

This feature checks the telephone line for the presence of a dial tone in those systems that are programmed to communicate with a central station. Note: Do not arm and disarm the panel just before making this test.

Hold down Key [6] until the sounder starts to pulse. If the line is okay, the pulsing will stop, otherwise a steady tone will sound (check phone lines). To silence the sounder, hold down Reset Key [9].

Note: Hold-Down Function 6 has a secondary feature (Manual Download) that can only be accessed within 5 seconds after arming and disarming the control panel. See DOWNLOADING FROM A COMPUTER for use of this feature.

Fault Find (Hold-Down Function 7)

When the Fault-Find mode is accessed, two things occur: (a) the loop response of all zones is preset to 7mS (fastest loop response), and (b) securing a zone in trouble will cause the sounder to beep for about 2 seconds. This set of conditions aids both installer and user. The installer, tapping and poking at suspect points, can easily locate swingers by listening for the beep. Similarly, the user can confirm the repair of a zone in trouble by listening for the beep, and thus eliminate the need of returning to the keypad to visually check after each attempt.

Hold down Reset Key [9] to restore normal operation. Arming the system successfully will automatically cancel the FaultFind mode.

System Trouble Indications

The following system troubles will display at the keypad, whether armed or disarmed, accompanied by flashing ARMED, STATUS and BYPASS LED's. The indication may be temporarily reset by holding down Reset Key [9] in order to check zone status and/or arm the system.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 10



1. AC Failure. Indicates loss of AC power. The AC-Failure

indication will clear when AC power is restored.

2. Low Battery. Displays when battery terminal voltage

drops below 11.5 volts, nominally. The system trouble display will be cleared and a restore reported when (a) the battery terminal voltage has returned to its specified restored level and (b) the keypad is reset using Hold-Down Function 9. Also see Bell / Battery Test.

3. Failure to Communicate. Indicates an unsuccessful

transmission to the central station. If the panel is armed, disarm. Hold down Key [9] to reset the keypad, then hold down Key [5] to test the phone lines. If the test is successful, the display will clear; otherwise the trouble will return,

flashing red ARMED/ALARM LED. Subsequent disarming will initiate the system trouble indication.

4. Auto-Download Failure. Indicates failure of a Function-6

Auto-Download. Reset the display by holding down Key [9], then try again to auto-download the program.

TESTING THE SYSTEM

After installation is completed, test the system a follows: Call the central station to inform them of the test. Initiate an alarm, preferably on a zone that activates a steady output. Verify proper signaling, then call the central station to confirm their receipt of a good transmission.

Important: Be sure to test the operation of all enabled keypad-panic features.

indicating a need for service. A successful communication followed by a Hold-Down [9] Reset will also clear the display.

Note: If the system is armed and in alarm, the sounder will

turn on but the violated zones will display, along with a

CHANGES FROM PREVIOUS EDITION

The following changes have been made to this manual (WI587E) since the previous edition (WI587D):

• Cover: UL Listing text descriptions changed to "UL/cUL".

• Page 3: 2nd paragraph, removed text "If complemented by NAPCO wireless transmitters…" (to end of paragraph).

• Page 4, 5, 18: Recommended battery specifications changed.

• Pages 4-5: Removed ordering information for certain items, including wireless equipment.

• Page 5: Updated UL classification information.

• Page 5 and 7: Renamed "Grade-A Bell" to "Mercantile Bell".

• Page 5: In "Summary of UL Requirements", removed bullet referencing Battery Fuse.

• Page 5: Updated UL Mercantile requirement descriptions.

• Page 10: Removed steps 4-6.

• Page 17: Added row to table 4, "Temporal Fire" output.

• Page 22: Removed text "

on Zone 7" description.

• Page 27: Removed entry, "Transmitters See R1000 Receiver Instructions WI604".

• Index: Re-created index entries.

• Page 31: Updated Wiring Diagram.

Note: A wireless transmitter mapped to Zone 7 may be used for remote arming." from "Key Input

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 11

4. PROGRAMMING

Page 11



KEYPAD PROGRAMMING

Keypad Programming may be divided into two sub-groups: User Program Mode and Dealer Program Mode. USER KEY- PAD PROGRAMMING is limited to user codes. In the Dealer Program Mode, the keypad provides full programming capabilities.

Dealer Keypad Programming.

Set the keypad to the Dealer Program Mode: Hold down Key [8] until a beep sounds, then enter the Dealer Program Code. (The default Dealer Program Code is 4,5,6,7,8,9, but this code must be reprogrammed to preserve system security. See Glossary and the programming example, which follows). The center segment of the numeric display will light to indicate the Dealer Program Mode.

The Dealer Program Mode cannot be accessed while the panel is armed or communicating except during the first three minutes after power-up. (See Power-Up Delay in Glossary). To shut this 3-minute "window" early, that is, before it times out, hold down Key [9]. Note: If the Dealer Program Mode has been accessed during this 3-minute "window", then complete the required programming, exit the Dealer Program Mode (see following), power down and power up the system once again.

Set the location to be programmed by pressing Key [B] (the three horizontal segments of the display and the green LED will light), followed by the location number. Each location must be entered as a three digit number, that is, 001, 020, 157, etc. Notice that as each of the three digits is entered, the three display segments extinguish in succession from bottom to top. When the last digit is entered, the yellow LED will light and the display will show the data (if any) programmed in that location.

At this point, several numeric keys take on new function assignments, as shown in Fig. 3.

Keys [1] or [6] (Prior Location) and [2] or [3] (Next Location) - Change the location. Use Key [1] or [6] to move down

to the next lower location, or Key [2] or [3] to move up to the next higher location. Whenever a new location is entered, a beep will sound.

Keys [4] (Data Up) and [7] (Data Down) - Select the data

for the chosen location: numbers 1-9, 0, and letters B, C, D, E, and F, as will be indicated in the display. Key [4] sequences data values in ascending order; Key [7], in descending order.

Key [5] (Clear) - Clears data from the selected location

(display will go blank).

Key [8] (Exit) - Exits the Dealer Program Mode. Hold down

until the beep sounds, then enter the Dealer Program Code within 10 seconds to exit.

Key [B] (Set) - Sets the location to be programmed. After

pressing Key [B], enter a three-digit location number.

To exit the Dealer Program Mode, hold down Key [8] until the beep sounds; all four LED's will light. Within 10 seconds, enter the Dealer Program Code; the LED's will go out. (If the LED's go out before your code is entered, repeat this procedure).

Caution: Before exiting the Dealer Program Mode, be sure that Location 083 contains the data shown in Table 2. lf the control panel comes up armed on power-up, you have three minutes to access the Dealer Program Mode. Hold down Key [8] for two seconds, then enter your Dealer Program Code. By checking Location 083, you can prevent accidental erasures of required data from going undetected. (If invalid data resides in Location 083, a non-existent fire trouble and/or loss of keypad functions may result). If you encounter this problem and need assistance, call Napco's Technical Service Department (toll free) at (800) 645-9445.

Disarmed Armed

5 7, D or F

Table 2. Valid data for Location 083

Example 1. Reprogram the existing (default) Dealer Program Code to 8,1,5,4,8,7.

1. Hold down Key [8] until the beep sounds.

2. Enter the existing (default) Dealer Program Code, 4,5,6,7,8,9. The center segment of the display will light.

3. Set Location 244, the first location of the Dealer Program Code block, as follows: (a) Press Key [B] (the three horizontal display

segments and green LED will light); (b) press [2],[4],[4] (the yellow LED will come on and the display will indicate the first digit of the existing code, "4").

4. Program the first digit of the new Dealer Program Code as follows: Press Key [4] (Data Up) repeatedly until an "8" is displayed.

5. Press Key [2] (Next Location) once to advance to Location 245, the second digit of the code. A "5" (the second digit of the de-

fault code) will be displayed. To program the second digit of the new code press Key [5] (Clear), then press Key [4] (Data Up) once - a "1" will be displayed.

6. Press Key [2] (Next Location) once again to advance to the third location (246) of the code. Using Key [7] (Data Down), replace

the "6" with a "5".

7. Repeat this procedure, using Key [2] to advance locations and Keys [4] and [7] to select data, until the entire code has been re-

programmed. To check the code, press Key [1] (Prior Location) five times to return to Location 244, then press Key [2] to step through each location, noting the data displayed.

8. To exit the Dealer Program Mode, hold down Key [8] until the beep sounds, then enter the new Dealer Program Code within 10 seconds. This will confirm operation of the new code.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 12



ENTER/EXIT PROGRAM MODE HOLD DOWN KEY [8] UNTIL BEEP SOUNDS. ENT ER DEALER PROGRAM CODE.

SEGMENTS LIT

2: PRESS "SET" (with no LED's lit) TO SET 3-DIGIT LOCATION.

3,2,1: ENTER 1ST OF 3 DIGITS. 3,2: ENTER 2 3: ENTER 3

2: ENTER DEALER CO DE (with all LED's

OF 3 DIGITS.

DIGIT; DATA DISPLAYED.

lit) TO EXIT.

MAGNUM ALERT

3 2 1

LOCATION DATA PAGE 1

LED'S LIT

GREEN: .......... ENTER LOCATION DIGITS

YELLOW: ........ VIEW/CHANGE DATA

RED (RIGHT) : . PAGE-1 LOCATION

ALL: ................ READY TO EXIT

LOCATION KEYS [1] (OR [8]) AND [2] (OR [3]) BEEP = SHIFTED 1 LOCATION NO BEEP = NO SHIFT

COMPUTERIZED SECURITY SYSTEM

LOCATION

PRIOR NEXT NEXT DATA UP

5 6 7 8

CLEAR PRIOR DATA DOWN ENTER/E XIT

9 F

2 1 3 4

PROGRAMMING SHEETS

Programming Sheets similar to those that follow are completed when planning system features and communicator information for the particular installation. These sheets should be retained for future reference. The Glossary contains information and instructions for programming each feature.

General Programming Steps

1. Contact the central station to confirm receiver format, data

format, event codes, subscriber numbers and telephone

number(s). Two receiver descriptions and telephone num-

bers, and up to 4 Subscriber Identification Numbers may be

required.

2. Fill out the Programming Record Sheets by circling the

numbers representing the zone features or system features

to be programmed. Referring to the programming sheets

and the accompanying table, note that each program loca-

tion is assigned data values (1, 2, 4, 8) such that adding

any combination will produce a unique total (entry). Also

note that because the entry can be only one character, the

two-digit totals greater than 9 are replaced by zero and let-

ters B through F, as shown. Check the Glossary for guid-

ance in selecting "data" entries.

SET

3. To program the subscriber PROM, follow the instructions furnished with the programmer. While programming, remember to keep the address page number in mind, and be sure that the position of the PAGE switch (PRO410/410M) is set accordingly. Note: If using the Napco PRO410/410M programmer, before attempting to program either page, be sure that all data in programmer memory are erased (press [ERASE], then [EXECUTE]).

4. Program the entries (data totals from Programming Record Sheets in Step 2) into the respective locations. The display will show the entry numerically, but will display "0" for the number 10, and letters "B", "C", "D", "E", and "F" for the numbers 11 through 15, respectively. To program a 10, enter [0]. To program 11 through 15, enter [B] through [F] respectively, if using the Napco PRO410/410M programmer to program a PROM, use the [PLUS] key to enter any two or more digits that add up to the desired entry. To program 13, for example, enter either [d] or [8] [PLUS] [5], or [8] [PLUS] [4] [PLUS] [1], etc. Similarly, to add to an existing PROM location, first press the [PLUS] key, then the complementary digit, otherwise the digit entered will re- place the digit in memory. Refer to the PRO410/410M instructions for further programming information.

Example 2. Program Zones 1-7 to report on alarm. Referring to the Communicator Information section of the Programming

Sheet, Report on Alarm is contained in Locations 166 and 167. Circle data values for Zones 1-7.

Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8/

Report on Alarm

166 166 166 166 167 167 167 167 Location

1 2 4 8 1 2 4 8 Data

Add the data values for Location 166: 1 + 2 + 4 + 8 = 15. From Table 3, 15 is programmed as an "F". Now add the data values

for Location 167: 1 +2 + 4 = 7. From Table 3, enter a "7" In Location 167.

MA1008e / 1008eM Installation Instructions

Panic

L NAPCO Security Systems

Page 13



LOCATION XXX ENTRY

blank

(1) 1

(2) 2

(1) (2) 3

(4) 4

(1) (4) 5

(2) (4) 6

(1) (2) (4) 7

(8) 8

(1) (8) 9

(2) (8) 0 (10)

(1) (2) (8) B (11)

(4) (8) C (12)

(1) (4) (8) D (13)

(2) (4) (8) E (14)

(1) (2) (4) (8) F (15)

Table 3. Determining data entry for a location. Numbers in pa-

rentheses indicate selected zones or features.

(See Programming Sheet.)

DOWNLOADING FROM A COMPUTER USING NAPCO SOFTWARE AND INTERFACE

Local Downloading

Data may be locally downloaded with the use of PCL2000 Local Download Cable, which is supplied with the PCI2000 interface. The panel need not be wired nor the keypad connected. Also refer to the instructions included with the PCI2000.

1. Referring to the PCI2000 Wiring Diagram, connect the PCL2000 Local Download Cable between the modem LINE connector and the control panel TELCO terminals. (Remove the plug shown coming from the PCI2000-J5).

2. With the control panel unpowered, set up the computer for a Function-6 Method download.

3. When a high-pitched tone is heard at the modem, power up the panel (connect the battery or transformer). A connection will automatically be established, ignoring the status of the zones.

4. Make all required selections and download the program.

5. After the computer indicates a successful download, terminate the connection, then remove power to the panel.

Remote Downloading

Data may be remotely downloaded to the panel via telephone lines using an IBM PC-compatible computer with Napco PCD2000 software and PCI2000 interface. Onscreen prompting and the extensive use of help menus simplify programming, and an error-checking mode locates omissions and incompatible data to reduce the possibility of mistakes. Remote downloading requires (a) a modem compatible with the PCI2000 and (b) PCD2000 software Version 2.E or higher. Note: Remote downloading may be disabled through programming and must be disabled in UL installations.

A program may be downloaded remotely using either of the following procedures.

Callback Method. This method is used to download to an unattended panel. The MA1008e will accommodate an an-

swering machine at the site if line seizure is used on the house phones. Program a "1" in Location 082 (Enable Download with Answering Machine). Refer to the instructions furnished with the PCD2000 for details. Note: The number of rings programmed into the panel must exceed that of the answering machine.

Function-6 Method. Call the central station from the site

to request a Manual Download. During this procedure, voice contact will be lost, therefore both the installer and the computer operator should be familiar with the operation. When a high-pitched tone is heard at the site phone, arm the panel, disarm, then access Hold-Down Function 6 (Manual Download) within 5 seconds; the site phone will go dead. Hang up the phone and wait for a call from the central station confirming a successful download.

Auto-Download Method. Napco PCD2000 Software Ver-

sion 2.E and later includes PC-Preset, a utility wherein blocks of up to 99 programs each may be preset for remote uploading or downloading from the installation site while the computer is unattended. The Auto-Download ID Number identifies the pro- gram in the computer that will be selected. (Note that the Dealer Program Code in the PCD2000 must agree with that of the control panel for the remote connection to be established.)

At the installation site, the Auto-Download ID Number corresponding to that in the computer is programmed into the panel, along with the Callback Telephone Number of the com- puter. To execute an Auto-Download, arm the panel, disarm, then access Function 6 within 5 seconds.

PROM PROGRAMMING

A blank DD493BNK PROM may be programmed using a PRO410 or PRO410M Programmer. See General Program- ming Steps and the manual furnished with the programmer for operating instructions, and also the Programming Record Sheets that follow. PROM programming may be used to program all features except the Dealer Program Code (Locations 244-249) and User Arm/Disarm Codes.

The following programming is required:

• Page-0, Location 083: "5"

• Page-1, Location 251: "C"

• Page-1, Location 252: "4"

Transferring Memory from PROM

Data programmed in the PROM are saved in memory as follows:

1. At the panel, with AC and battery power off, insert the programmed PROM into the MEMORY CHIP socket. Align the dot on the PROM with the dot on the circuit board.

2. Apply ac power. Enter the Dealer Program Mode: Hold down Key [8] until the function beep sounds, then enter the Dealer Program Code.

3. Exit the Dealer Program Mode: Hold down Key [8] until the beep sounds, then enter the Dealer Program Code.

4. An "L" or "LOADING PROM" will display at the keypad. When loading is complete, remove both AC and battery power, remove the PROM from the socket, then power up normally.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 14



PROGRAMMING RECORD SHEET FOR THE MA1008e

Communicator Features - Default programming shown in parenthesis.

REPORT ON ALARM 166 167 168 169

CONTROL - PANEL RESTORE 170 171 172 173

(SEE NOTE 1)

ZONE RESTORE 184 185

(SEE NOTE 1)

ALARM / TROUBLE

CODES

Extended or

Two Digit

RESTORE CODES S ingle Digit

Extended or

Two Digit

Single Digit

OPENING / CLOSING CODES CLOSING FORCE OPENING

SINGLE DIGIT

EXTENDED OR TWO DIGIT

SUBSCRIBER ID NUMBERS AL ARM/RESTO RE ID (SEE NOTE 3) OPENING/CLOSING ID

1 2 3 4 5 6 7 8

1 2 4 8 1 2 4 8 1 2 4 8 1 2 4

1 2 4 8 1 2 4 8

000 002 004 006 008 010 012 014 016 018 020 022 024 026 028 062

(3) (3) (3) (3) (3) (3) (3) (2) (1) (2) (F) (F) (F )

001 003 005 007 009 011 013 015 017 019 021 023 025 027 029 063

(1) (2) (3) (4) (5) (6) (7) (1) (1) (2) (1) (9) (8)

040 042 044 046 048 050 052 054 056 058 060 062 064 066 068

(E) (E) (E) (E) (E) (E) (E) (E) (E) (E) (E)

041 043 045 047 049 051 053 055 057 059 061 063 065 067 069

(1) (2) (3) (4) (5) (6) (7) (1) (F) (9) (8)

USER ARM USER

(1) (2) (3) (4) (SEE NOTE 2) (1) (2) (3) (4)

SELECT USER(S)

CLOSING

GROUP 1 GROUP 2 (SEE NOTE 4)

TELEPHONE 1 100 101 102 103 104 105 106 107 108 109 110 111

TELEPHONE 2 132 133 134 135 136 137 138 139 140 141 142 143

030 032 034 036

031 033 035 037

GROUP 1 GROUP 2

ZONE K/P FIR DAY TST NO LOW

1 2 3 4

174

1 2 4 8

038

039

SELECT USER(S)

FIR AMB TBL TBL TMR AC BAT AUX

1 2 3 4

070 072 074 076

OPENING

071 073 075 077

176

1 2 4 8

CUSTOMER: DATE:

ACCOUNT NO. TEL:

ADDRESS:

FORMAT

RCVR DATA

TELEPHO NE 1

(E)

TELEPHO NE 2

(E)

286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301

ENTRY RECEIVER FORMAT

BLANK ADEMCO, SILENT KNIGHT SLOW

1 SESCOA, VERTEX, DCI, FRANKLIN (SEE NOTE 5)

2 RADIONICS FAST (SEE NOTE 5)

3 SILENT KNIGHT FAST

4 RADIONICS, DCI, FRANKLIN SLOW (SEE NOTE 5)

5 UNIVERSAL HI-SPEED

6 FOR 2300HZ HANDSHAKE, ADD AN "8" TO THIS LOCATION

112 113 114 115 116

144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163

PRE ACC D/T

DLY NO. DET

# OF

RINGS

269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285

MA1008e / 1008eM Installation Instructions

TELEPHONE NUMBER 1

117 118 119 120 121 122 123 124 125 126 127 128 129 130 131

TELEPHONE NUMBER 2

CALLBACK TELEPHONE NUMBER 1

NOTE: PROM LOCATIONS

ARE 013 - 029, PAGE 1

CALLBACK TELEPHONE NUMBER 2

ENTRY DATA FORMAT

BLANK EXTENDED OR SINGLE DIGIT

1 SINGLE DIGIT

2 TWO DIGIT (OR 4/2)

4 SUM CHECK

NOTES: (1) IF PROGRAMMING ZONE RESTORE, ALSO PROGRAM CONTROL-PANEL RESTORE. (2) TWO DIGIT FORMAT ONLY. (3) GROUP-2 CODES MUST BE ENTERED, EVEN IF THEY ARE THE SAME AS GROUP 1 CODES. (4) MUST BE PROGRAMMED IF OPENING/

NOTE: PROM LOCATIONS

ARE 030 - 045, PAGE 1

CLOSING CODES ARE PROGRAMMED. (5) THESE FORMATS TYPICALLY USE A 2300HZ HANDSHAKE; ADD AN "8" TO THIS ENTRY.

L NAPCO Security Systems

Page 15

PROGRAMMING RECORD SHEET FOR THE MA1008e

Zone Features & Keypad Codes - Default programming shown in parentheses.

ZONE FEATURES

SWINGER SHUTDOWN 184 085

NO END-OF-LINE RESISTOR 086 087

CHIME ZONE 088 089

NEVER ARM 090 091

PIR ZONE 092 093

UNTIMED OUTPUT 096 097 098 099

(ONTO LUG 15)

ENABLE KEYPAD SOUNDER 164 165

ON ALARM

DAY ZONE 186 187

PRIORITY ZONE WITH BYPASS 188 189

(SEE NOTE 1)

PRIORITY ZONE 190 191

REMOVE AUTO BYPASS 192 193

(SEE NOTE 1)

SELECTIVE BYPASS 194 195 REFER TO R1000 RECEIVER INSTRUCTIONS

GROUP BYPASS 196 197

24-HOUR PROTECTION 198 199

AUTO-RESET 200 201

EXIT / ENTRY ZONE 202 203

(ENTRY DELAY 1)

EXIT / ENTRY ZONE 204 205

(ENTRY DELAY 2)

EXIT / ENTRY FOLLOWER 206 207

ABORT DELAY 208 209

BURGLARY OUTPUT 210 211

7mS LOOP RESPONSE 214 215

(SEE NOTE 2) 1 2 4 8 1 2 4 8

50mS LOOP RESPONSE 216 217

(SEE NOTE 2) 1 2 4 8 1 2 4 8

FIRE ON BURGLARY ZONE 306 307

(SEE NOTE 3) 1 2 4 8 1 2 4 8

1 2 3 4 5 6 7 8

1 2 4 8 1 2 4 8

1 2 4 8 1 2 4 8 1 2 4 8 1 2 4 8

1 2 4 8 1 2 4 8

GROUP 1 GROUP 2

ZONE K/P FIR DAY TST NO LOW

FIR AMB TBL TBL TMR AC BAT ARM

<--(ALSO SEE TIMES & TIMEOUTS, LOC. 230-231)

<--(SEE NOTE 7)

<--(ALSO SEE TIMES & TIMEOUTS, LOC. 094-095)

<--(SEE NOTE 7)

<--(ALSO SEE TIMES & TIMEOUTS, LOC. 218-219; 220-221)

<--(SEE NOTE 7)

<--(ALSO SEE TIMES & TIMEOUTS, LOC. 218-219; 222-223)

<--(SEE NOTE 7)

<--(ALSO SEE TIMES & TIMEOUTS, LOC. 232-233)

<--(ALSO SEE TIMES & TIMEOUTS, LOC. 224-225; 228-229)

NOTE: For wireless systems, refer to R1000 Receiver Installation Instructions (WI604) for Transmitter Mapping Locations 308-315.

<--(SEE NOTE 7)

TRANSMI TTER ZONE M AP

(FOR WIRELESS SYSTEMS ONLY)

TX# LOC ZONE

1 308

2 309

3 310

4 311

WI604 FOR TRANSMITTER MAPPING AND LEARNING INSTRUCTIONS AND OTHER WIRELESS INSTALLATION INFORMATION.

TX# LOC ZONE

1 312

2 313

3 314

4 315

Page 15



KEYPAD CODES (DO NOT ENTER ZEROS)

SEE NOTE 4

AMBUSH USER PROGRAM CODE DEALER PROGRAM CODE

236 237 238 239 240 241 242 243 244 245 246 247 248 249

(1) (2) (3) (4) (5) (6) (4) (5) (6) (7) (8) (9)

USER 1

316 317 318 319 320 321 322 323 324 325 326 327

USER 5 USER 6

332 333 334 335 336 337 338 339 340 341 342 343

ENTRY TOTAL: 2 3 4 5 6 7 8 9 10 11 12 13 14 15

PROGRAMMER DISPLAYS ● 2 3 4 5 6 7 8 9 0 B C D E F

USER 2

See Note 5 See Note 6

NOTES: (1) If programming PRIORITY ZONE WITH BYPASS, do not program REMOVE AUTO BYPASS. (2) If neither 7mS nor 50mS LOOP RESPONSE is pro-

grammed, Loop response will be 750mS. (3) FIRE ON BURGLARY ZONE's must also be programmed for 24-HOUR PROTECTION, but for no other zone features except UNTIMED OUTPUT. (4) The Dealer Program Code must not start with the same numbers as the User Program Code. (5) ● (dot) or blank for no entry. (6) To conform with Telephone Company convention, program zeros in Telephone Numbers, Alarm Codes and Subscriber ID Numbers as an entry total of 10. (Press DATA UP button until "0" is displayed; in PRO410, press Key [0].) (7) Zone "8" for wireless operation only. To use as other than keypad Panic, also program DIRECT KEYPAD PANIC TO AMBUSH (see GLOSSARY).

L NAPCO Security Systems

USER 3

USER 7

USER 4

328 329 330 331

USER 8

344 345 346 347

MA1008e / 1008eM Installation Instructions

Page 16



PROGRAMMING RECORD SHEET FOR THE MA1008e

System Features & Timeouts - Default programming shown in parentheses.

SYSTEM FEATURES

INSTRUCTIONS: FOR EACH LOCATION: (1) CIRCLE NUMBERS FOR FEATURES DESIRED. (2) PLACE SUM OF CIRCLED NUMBERS IN "ENTRY" BOX. WARNING: DO NOT ATTEMPT TO PROGRAM "RESERVED" LOCATIONS AS IMPROPER OPERATION MAY RESULT.

LOCATION 078 ENTRY--> DISPLAY DAY ZONES AFTER RESET 1

FAILURE TO COMMUNICATE ON NTO LUG 2

USER 5 ARM ONLY 4

USER 5 REPORT AS USER 1 8

LOCATION 079 ENTRY-->

USER 5 SERVICE CODE 1

DISABLE DAY-ZONE REPORT 2

USERS 6, 7, 8 REPORT AS USERS 2, 3, 4 4

KEYPAD AUXILIARY ALARM ON NTO LUG 8

LOCATION 080 ENTRY-->

DIRECT KEYPAD PANIC TO AMBUSH 1

DIRECT ZONE 8 TO AMBUSH 2

DISABLE CALLBACK DOWNLOAD 4

DISABLE FUNCTION-6 DOWNLOAD 8

LOCATION 081 ENTRY-->

WATCH ON WITH GROUP BYPASS 1

CHIME ON WITH GROUP BYPASS 2

DISPLAY OPEN ZONES 4

DISABLE DISPLAY BYPASS 8

LOCATION 082 ENTRY-->

ENABLE DOWNLOAD W/ANSWERING MACH. 1

REMOTE STATUS LED ON NTO LUG 2

ENABLE KEYPAD FIRE (SEE NOTE 1) 4

ENABLE K EYPAD AUX. (SEE NOTE 1) 8

LOCATION 178 ENTRY--> TOUCHTONE DIALING 1

TOUCHTONE WITH ROTARY BACKUP 2

BACKUP REPORTING 4

DOUBLE REPORTING 8

LOCATION 179 ENTRY-->

OPENIN G REPORT AFTER ALARM 1

FORCE ARM 2

STATUS REPORT 4

SPLIT REPORTING 8

LOCATION 180 ENTRY-->

AUDIBLE TEST ON ARMING 1

AUTO-RE SET AFTER AL ARM TIMEOUT 2

POWER UP IN LAST STATE 4

SOUNDER OUTPUT ON LUG E4 8

LOCATION 181 ENTRY-->

PULSING FIRE OUTPUT 1

RESET FIRE ZONE 2

ENABLE KEYPAD TACTILE BEEP 4

RESET TEST TIMER ON REPORT 8

LOCATION 182 ENTRY-->

DISABLE FAULT FIND 1

ENABLE KEYPAD PANIC 2

ENABLE COMMUNICATOR CONF. TEST 4

DISABLE BELL TEST 8

LOCATION 183 ENTRY--> DISPLAY AN Y BYPASS 1

NO OPNG REPT AFTER ALRM ON ZONE 6 2

INCL MANL BYP IN FORCE-ARM/STATUS 4

KEY INPUT ON ZONE 7 8

LOCATION 304 ENTRY-->

DON'T WAIT FOR HANDSHAKE, TELCO 1 1

DON'T WAIT FOR HANDSHAKE, TELCO 2 2

(RESERVED) 4

(RESERVED) 8

LOCATION 305 ENTRY-->

AUDIO VERIFICATION ON NTO LUG 1

BURGLARY OUTPUT ON AMBUSH 2

RESET SHOCK SENSORS ON ARMING 4

DISABLE LOW-BATTERY DISPLAY 8

TIMES & TIMEOUTS

TIME EXAMPLES

TIME 1ST BOX 2ND BOX

5 5 NONE

10 0 NONE

15 F NONE

30 E 1 230 231

45 D 2

60 C 3

X1 X16

094 095

250 251

X1 X16 DELAY TIME

218 219

220 221

222 223

232 233

SENSOR WATCH (HOURS)

TEST-TI MER OFFSET (HOURS)

EXIT DELAY

(D, 2) (SECONDS)

ENTRY DELAY 1

(SECONDS)

(E, 1)

ENTRY DELAY 2

(SECONDS)

(E, 1)

ABORT DELAY

(SECONDS)

DD493BNK PROM Required Programming: Page 0, Location 083 = "5"; Page 1, Location 251 = "C"; Page 1, Location 252 = "4"

ENTRY TOTAL: 2 3 4 5 6 7 8 9 10 11 12 13 14 15

PROGRAMMER DISPLAYS ● 2 3 4 5 6 7 8 9 0 B C D E F

See Note 3 See Note 4

NOTES: (1) This feature requires that all system keypads have F/P/A keypad panics. (2) Program in decimal numbers; do not use leading zeros. (3) ● (dot) or blank

for no entry. (4) To conform with Telephone Company convention, program zeros in Telephone Numbers, Alarm Codes and Subscriber ID Numbers as an entry total of

10. (Press DATA UP button until "0" is displayed; in PRO410, press Key [0].)

X1 X16 TIMEOUT

224 225

228 229

X1 X10

252 253

254 255

BURG OUT TIMEOUT

(F, ) (MINUTES)

FIRE TIMEOUT

(F, ) (MINUTES)

CHIME TIME

(8, ) (1/4 SECONDS)

AUTO D/L ID NO.

(SEE NOTE 2)

CALLBACK SELECT

(ENTER 1 OR 2)

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 17

5. GLOSSARY & PROGRAMMING DATA

Page 17



Abort Delay (Locations 208, 209; 232, 233)

A delay period that allows cancellation of the central sta-

tion report. This is done by disarming the panel within the delay period. Program Locations 208-209 for zone selection; Locations 232, 233 for delay time (see Time Selection). The NTO Lug E15 will be subject to the abort delay if Untimed Output and Abort Delay are programmed for the same zone. Note: If Abort Delay is selected for a 24-Hour Zone or a Zone-Restore Zone, the cause of the alarm must be corrected before disarming the panel.

AC-Failure Reporting (Locations 169;173)

If AC is removed from the panel, the first three LED's will flash slowly and a "1" will be displayed (while armed or disarmed). If disarmed, holding down Key [9] will reset the indication for about three minutes to permit arming. However, the failure indication will return within a few minutes, whether armed or disarmed, unless AC power is restored. If programmed for Report on Alarm, the report will be delayed for 1 hour. Restores report immediately.

Access Number for Outside Line (Locations 115, 147)

Some subscribers will have a telephone system that requires one digit to access an outside line before the telephone number can be dialed. Also, the first dial tone encountered (prior to the access number) may have a frequency that is different from that of the accessed dial tone (440Hz). One or more 4-second Pre-Dial Delay "D"s may be entered before the access number instead of a dial tone with frequency "E". See Pre-Dial Delay.

If your subscriber's system uses an access number:

1. Contact the telephone-equipment supplier to find out if a dial tone other than 440Hz is received prior to dialing the access number. If the communicator must delay before dialing the access number instead of attempting to recognize the dial tone, find out how many 4-second delays must be programmed.

2. For Telephone 1, (a) enter the Dial-Tone Detection "E" or Pre-Dial Delay "D" in Location 114. Enter any extra "D" that may be required starting in Location 115; (b) enter the access number digit in Location 115, or the first available location thereafter; (c) starting in the first available location after the access number, enter any Pre-Dial Delay "D"s needed before the second dial tone; the Dial Tone Detection "E" for the second dial-tone fre-

quency; then the telephone number.

3. If Telephone 2 is used, repeat step 2 starting in location

146. (See Backup Reporting; Double Reporting; and Split Reporting). Also see Dial-Tone Detection; Pre-Dial Delay.

Alarm Codes See Report on Alarm

Alarm History

Hold-Down Key [B] will display (on the digital readout) all alarm conditions that have occurred. While holding down Key [B], note the number(s) displayed indicating the zone(s) violated. When the system is rearmed, the previous alarm history will stay memorized until automatically erased by a new alarm condition. Note that Alarm History will not display Fire, Fire Trouble, Ambush, or zones directed to Ambush, but it will display Fire on Burg Zone alarms.

Alarm Outputs (Locations 181, 210-211; 224-225; 228-229; Terminals 3, 4; NTO Lug E15)

The MA1008e has a common Burglary/Fire siren output at Terminals 3 and 4. Steady bell and pulsing bell outputs for Burglary and Fire, respectively, are selectable options. Table 4 summarizes wiring and programming for signaling an alarm in typical installations. Refer to Time Selection for timeout durations.

Ambush Code (Locations 236, 237) Burglary Output on Ambush (Location 305)

A 1- or 2-digit code that is entered by the user prior to disarming to access the Ambush Zone, causing a silent report to be sent to a central station. Thus, should a user be forced to disarm by an assailant, he can silently signal an emergency while appearing to be merely disarming the system. The Arm/Disarm Code must be entered less than 10 seconds after the Ambush Code for an ambush report to be transmitted. The Ambush Zone will automatically report when programmed to report on alarm.

To program the ambush feature, (a) program Ambush to Report on Alarm (enter a "2" in Location 168); (b) enter 1 or 2 digits as the Ambush Code In Locations 236-237; (c) enter an Ambush alarm report code in Locations 018-019.

Inform the user what the Ambush Code is, and that his arm/disarm code must be entered less than 10 seconds after the Ambush Code for an ambush report to be sent.

Burglary Output on Ambush may be programmed in

Output Wiring Output Locations Timeout Locations Remarks

Sweep Siren Speaker on 3 (+) & 4 (–) 210, 211 224, 225 –

Fire (Steady) Siren Speaker on 3 (+) & 4 (–) – 228, 229

Fire (Pulsing) Siren Speaker on 3 (+) & 4 (–) "1" in location 181 228, 229

Steady Bell Bell on 3 (+) & 4 (–) 210, 211 224, 225

Pulsing Bell Bell on 3 (+) & 4 (–) "1" in location 181 228, 229

Temporal Fire Bell on 3(+) & 4 (–) "C" in location 175 –

Untimed Output (NTO) E15 (–) & 5 (+) 096-999 –

Note: (1) For UL Residential Fire installations, use a bell on Terminals 3 (+) and 4 (-); cut Jumpers E and PS and install Jumper J2 (see Wiring Diagram). See Time Selection for timeouts. (2) Cut Jumper to prevent the fire signal from sounding a steady siren (or bell, if Jumper E is cut). (3) Cut Jumper D to produce an alternating two-tone siren sound.

L NAPCO Security Systems

Fire Zones only

Cut Jumper E

Fire Zones only; cut Jumper E

Provides supervised Bell Output

<300mA for strobes, etc. See NTO.

Table 4. Alarm Outputs

MA1008e / 1008eM Installation Instructions

Page 18



conjunction with either Direct Zone 8 to Ambush or Direct Keypad Panic to Ambush to sound are audible alarm when ambush is tripped. Also see Direct Keypad Panic to Ambush; Direct Zone 8 to Ambush.

Anti-Jam Time

If the communicator does not detect a dial tone within 12 seconds, the Anti-Jam feature will be activated. That is, the communicator will go off-line for a 15-second anti-jam interval in order to free the telephone circuit from incoming calls, then make another 12-second attempt at dial-tone detection. If still unsuccessful, the communicator will again go off-line for 15 seconds, then proceed to dial anyway.

To test the Anti-jam feature, call the alarm phone line from a different phone line, then activate an alarm. The incoming call should be disconnected by the control panel.

Arm Lug (Lug E4)

Lug E4 (ARM) will go to approximately 1Vdc when the system is armed. This lug may be used for auxiliary equipment. For use, refer to the instructions furnished with the peripheral device. Also see Sounder Output On Lug E4.

Audible Test on Arming (Location 180)

(Required for UL Mercantile installations). To test the alarm circuit each time the system is armed, add a "1" to Location

180. The alarm is then activated briefly about 8 seconds after the panel is armed. If the alarm does not sound, the device may be defective.

Audio Verification on NTO Lug See Untimed Output

Auto-Bypass Zone See Remove Auto-Bypass

Auto-Download ID Number (Locations 252, 253) Callback Select (Location 254)

Napco PCD2000 Software Version 2.E and later includes a PC-Preset utility wherein numerous programs may be preset for automatic remote uploading or downloading from the installation site while the computer is unattended (in standby mode). The Auto-Download ID Number identifies the program in the computer that will be selected. (Note that the Dealer Program Code in the PCD2000 must agree with that of the control panel for the remote connection to be established).

At the installation site, program the Auto-Download ID Number in Locations 252 and 253, in decimal numbers, corresponding to that in the computer. Also program the Callback Telephone Number of the computer. If two phone numbers are programmed, select the phone to be called in Location

254. Then, arm the panel, disarm and, within five seconds, access Function 5 to execute an Auto-Download.

Auto-Reset (Location 200-201) Auto-Reset After Alarm Timeout (Location 180)

If a zone signals an alarm and is selected for Auto-Reset, it will automatically rearm itself soon after the alarm condition is removed. Auto-Reset may be delayed to occur after the timeout period by programming a "2" in Location 180.

Zones 1--8/Panic that are not programmed for Auto-Reset will not be capable of signaling another alarm until (a) the cause of the alarm has been removed and (b) the panel is disarmed.

Also see Swinger Shutdown.

Backup Reporting (Location 178)

When Backup Reporting is selected and the communicator

does not reach the first telephone number after two attempts, seven attempts will be made to reach the second telephone number. Enter Subscriber Identification Numbers for Telephone 2 (Locations 132-143) and other information required for Telephone 2 (Locations 144-163). If Double Reporting is selected with Backup Reporting, all reports sent to the first telephone number will also be transmitted to the second telephone number. However, if the first transmission fails, two reports will be sent to Telephone 2 (Double Reporting). Note: Subscriber Identification Numbers for both Telephones 1 and 2 must be entered, even if they are the same.

Battery

12VDC standby power source in the control panel to provide backup protection in the event of a power loss. The 4AH battery is supplied; the 7AH is available as an option. Note that the battery is an integral part of the system. It must be installed, even if AC power is present.

Battery Lug (Lug E14)

This is a fused battery output (3A) designed primarily for use with the MVA-1000 Talking Siren Driver.

Burg Lug (Lug E14)

Lug E10 (BURG) will go to about 1VDC when a burglary alarm is tripped. E10 may be used to trip an LW-900 LongRange Wireless interface. Or, a relay (400Ω minimum) may be connected between E10 and Terminal 5 (+ AUX. POWER) if a diode is wired in series (cathode to E10; anode to relay coil).

Burglary Output See Alarm Outputs

Burglary Output on Ambush See Ambush Code

Callback Telephone Number 1 (Locations 270-285;

PROM Page-1 Locations 014-029)

Callback Telephone Number 2 (Locations 286-301,

PROM Page-1 Locations 030-045)

Number of Rings (Location 269; PROM Page-1 Location

013)

The control panel will call back the PCI2000 as a security check prior to downloading when using the Callback Method. Provisions for two callback telephone numbers are made for the Auto-Download Mode. Program at least one callback number starting in Location 270. (Remember that a "D" or an "E" must be programmed before the telephone number - see Telephone Numbers). The panel will initiate the callback after waiting 15 rings, unless programmed otherwise. To change the number of rings before callback, enter the desired number of rings (3 minimum, 15 maximum) in Location 269. Also see Auto-Download ID Number.

Chime Zone (Location 088-089) Chime On with Group Bypass See Group Bypass

This annunciator feature may be programmed for any zone to sound at the keypad while disarmed when the zone goes into trouble. Hold down Key [5] until the function beep sounds to enable or disable the Chime. Chime duration is programmable (Locations 230, 231) in units of 1/4 seconds. See Time Selection. The Chime-Zone number will be displayed for the duration of the programmed chime time, or for as long as the zone is open (or shorted), whichever is greater. Also see Never-Arm Zone. Note: A "1" in Location 230 will prevent the sounder from coming on.

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 19



Closing Report (Select User(s) Closing) (Location 174) Force Arm Report (Locations 179; 038-039) Status Report (Locations 179; 000-029; 038-039) Include Manual Bypass in Force-Arm/Status Report

(Location 183)

On arming, the communicator can transmit a closing code for each user, a Force-Arm Code, and a Status Report that identifies the problem zone to the central station. Note that Subscriber Identification Numbers (Locations 108-111; 140-143) and Closing Codes (Locations 030-037) must be entered for any closing report. Program closing report (Select User(s) Closing, Location 174) to report each time the panel is armed. Each of up to four users may have his own Closing Code (Locations 030-037).

Select Force Arm Report ("2" in Location 179) to report only when arming with an auto-bypassed zone. This transmission will consist of a Closing Code followed by a ForceArm Code. Select both closing report and Force Arm to always send a closing report, and a Force Arm report only if one or more zones were auto-bypassed. Also see Prior- ity Zone with Bypass.

Select Status Report ("4" in Location 179) to send a Force Arm report followed by a Status Report that identifies the auto-bypassed zone(s). The second Alarm-Code location is usually used for this purpose. If this location is vacant, the first location will be used.

To include manual bypasses in a Force Arm/Status Report, program a "4" in Location 183. (Either Force Arm or Status Report must also be programmed).

Following is an example of a typical Force-Arm/Status Report.

Example. A burglar breaks into a commercial establishment during the night, breaking the window foil. The Alarm Subscriber Identification Number is '"123"; the Alarm Code is "1" (Burglary Zone 1); the Opening/Closing Subscriber Identification Number is "456"; the Force-Arm Code is "F"; the Closing Code for User 1 is "C". The communicator will send the following report to the central station (single-digit data format):

1231 - Sent when alarm occurs. 456B - Opening; User returned and inspected damage. 456C - Closing. CCC1 - User 1 rearmed. 456F - Force Arm. FFF1 - Zone status at time of closing: Window foil still

Control-Panel Restore See Restore Report

broken. Zone 1 auto-bypasses; repair required.

Data Format (Locations 113,145)

Consult the central station to find out which of the following formats to use.

Extended Format. Extended-format reporting allows the communicator to transmit an extra digit to the central station. This extra digit is generally used to report the user or the zone on which the event occurred.

Example. An installation uses the following programmed transmission information: Subscriber Identification Number is ;"678"; a Closing Report is selected for User 3; Extended Format Closing Code is "C3" (Closing, User

3). If User 3 closes, the communicator will transmit:

678C - Subscriber "678" has closed.

CCC3 - Closing, User 3.

Extended Format may be used with most central-station receivers. Most receivers capable of recognizing multiple reporting will also recognize Extended Format. The central station will indicate the event codes to be programmed. Extended Format does not require any programming in Locations 113 and 145. To use Extended Format, follow Steps 2 through 5 of Two-Digit Event Code Format later in this section.

Single-Digit Event Code Format. If the receiver cannot accept extended reporting,

1. Program a "1" in Location 113 (and 145 for a second

telephone number, if used). See Double Reporting and Backup Reporting.

2. Enter the first digit for any Alarm/Trouble Code, Restore Code and Opening/Closing Codes.

Note: If it is desired to have a Single-Digit Event Code

for one telephone number and Extended Format for the other, program both digits for all event codes. Use the first digit to indicate the alarm type and the second digit to indicate the zone. The telephone number with a "1" in Location 113 (or 145) will transmit only the first digit. The other telephone number will use both digits. (Single-Digit Format will ignore the second digit of the event code).

Two-Digit Event Code Format. Some central-station

receivers require that a two-digit code be sent in each report.

Example. In a certain installation, the Alarm Subscriber Number is "123"; a burglar alarm occurs on Zone 1 (Alarm Code "31"). The communicator will send "12331".

To use Two-Digit Event Code Format,

1. Program a "2" in Location 113 (145 for a second tele-

phone number, if used). See Double Reporting and Backup Reporting.

2. Enter an Alarm Code (Locations 000-029) for each

zone or condition to report on alarm (see Report on Alarm) or for a Force-Arm/Status Report as follows: a. Enter the first digit of the Alarm Code. (This digit

may be used to indicate alarm type.)

b. Enter the second digit of the Alarm Code. (This

digit may be used to indicate the zone.)

3. Repeat Step 2 to enter Restore Codes (Locations 040-069) for each zone selected for Control-Panel Restore or Zone Restore (see Restore Report).

4. If Opening Report or Opening Report After Alarm is selected, enter a two-digit Opening Code for each user (Locations 070-077). See Opening Report; Opening Report After Alarm.

5. If Closing Report is selected, enter a two-digit Closing Code (Locations 030-037) for each user. If a Force Arm or Force-Arm/Status Report is selected, also enter a two-digit Force-Arm Code (Locations 038, 039).

Note: Single-Digit Format will override Two-Digit For-

mat in Locations 113 and 145 if both are pro- grammed.

Sum-Check Format. Sum Check is a sophisticated

data format used to enhance the speed and check the accuracy of the received transmission. This format should be preferred if the central station is capable of receiving it.

After transmitting the Subscriber identification Number and the event code, the communicator sends a verifying digit that is the sum of both. The receiver compares the

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 20



verifying digit with the sum of the other two numbers to check transmission accuracy. To select Sum Check, program a "4" in Location 113 (or 145 for a second telephone number, if used).

Day Zone (Locations 186, 187) Disable Day-Zone Report See PIR Zone Display Day Zones After Reset (Location 078)

A Day Zone is a Burglary Zone that will cause visual and audible indication at the keypad if the loop has an open condition only when disarmed. This feature may be used to warn of trouble during the day, when the control panel is not armed. If the Day Zone experiences a problem (a break in a window foil, for example), the green STATUS LED on the keypad will flash, the sounder will beep repeatedly, and the display will indicate the problem zone(s). Hold down Key [9] to silence the sounder and clear the display. Arm and disarm the panel to reset the Day Zone.

If a "1" is programmed in Location 078 (Display Day Zones After Reset), the Day-Zone number(s) will continue to display after the sounder is silenced until the condition is corrected, and the Day Zone will auto-reset without the need to arm/ disarm.

Note: For high security Day-Zone supervision, also program Disable Fault Find (enabling Fault Find will disable Day- Zone supervision).

Also see Watch On with Group Bypass.

Dealer Program Code (Locations 244-249)

This code is required to enter the Dealer Program Mode. The default Dealer Program Code is 4,5,6,7,8,9, however this code must be changed to preserve system security. Reprogram the 3- to 6-digit Dealer Program Code starting in location

244. Note: (1) The Dealer Program Code must not start with the same numbers as the User Program Code. (2) The Dealer Program Code also serves as your Download Security Code.

Dial-Tone Detection (Locations 116,148)

At least one Dial-Tone Detection entry is usually required for each telephone number used to ensure that a dial tone is present before the communicator dials.

When an "E" is programmed before the first digit of an outside telephone number, the communicator dial-tone detection circuit is set to detect the standard 440Hz dial tone. The "E" is generally entered in Location 116 for Telephone 1 and Location 148 for Telephone 2, if used.

It may be necessary to program at least one 4-second Pre- Dial Delay before a Dial Tone Detection "E". With certain nonstandard exchanges, Pre-Dial Delay "D"s may be used without a Dial-Detection "E". (See Access Number for Outside Line; Pre-Dial Delay).

Direct Keypad Panic to Ambush (Location 080) Direct Zone 8 to Ambush (Location 080)

Program Direct Keypad Panic to Ambush ("1" in Location

080) to free Zone 8 for wireless use while providing silent panic. Or, select Direct Zone 8 to Ambush ("2" in Location

080) to have wireless transmitters that are mapped to Zone 8 send a silent report. (These will report using the Ambush Code).

Disable Bell Test (Location 182)

Program an "8" in Location 182 to prevent unauthorized persons from sounding the bell.

Disable Callback-Method Download (Location 080)

Data may be remotely downloaded to an MA1008e using Napco Quickloader™ software and interface if the correct download security code is known. Program this feature to prevent downloading to an unattended panel.

Disable Day-Zone Report See PIR Zone

Disable Display Bypass (Location 081)

For added security, this feature disables Hold-Down Function 2 and the BYPASS LED after exit delay expires.

Disable Fault Find (Location 182)

When the Fault-Find mode is accessed (Hold-Dawn Key [7]), two things occur: (a) the loop response of all zones is preset to 7mS (fastest loop response), and (b) securing a zone in trouble will cause the sounder to beep for about 2 seconds. This set of conditions aids bath installer and user. The installer, tapping and poking at suspect points, can easily locate swingers by listening for the beep. Similarly, the user can confirm the repair of a zone in trouble by listening for the beep and thus eliminate the need of returning to the keypad to visually check after each attempt.

Hold dawn Reset Key [9] to restore normal operation. Arming the system successfully will automatically cancel the Fault-Find mode. Program a "1" in Location 182 to prevent unauthorized use of the Fault-Find mode.

Disable Function-6 Download (Location 080)

An "8" in Location 080 will prevent manual remote downloading at the panel. See Manual Download.

Disable Low-Battery Display See Low Battery

Display Any Bypass (Location 183)

Hold-Down Function 2 (Display Bypass) normally displays manually-bypassed zones only, when Display Any Bypass is selected and a zone is auto-bypassed, the yellow BYPASS LED will light, and Hold-Down Function 2 will display AutoBypassed and Priority bypassed Zones as well.

Display Day Zones After Reset See Day Zone

Display Open Zones (Location 081)

A "4" in Location 081 will cause any non-24-Hour zone that is open (or shorted) while disarmed to automatically display at the keypad in addition to the flashing green LED.

Don't Wait for Handshake, Telco 1 (Location 304) Don't Wait for Handshake, Telco 2 (Location 304)

Select this feature for telephones not reporting to a central station. (This feature may be useful for demo purposes).

Double Reporting (Location 178)

When Double Reporting is selected, only information that is successfully sent to Telephone 1 will be sent to Telephone 2 as well. To program, enter an "8" in Location 178. Enter Subscriber Identification Numbers for Telephone 2 (Locations 132-143) and related information required for Telephone 2 (Locations 144-163).

If Backup Reporting is selected with Double Reporting, reports sent to the first telephone number will also be sent to the second. However, if the first transmission fails, two reports will be sent to Telephone 2. Split Reporting will override Double Reporting if both are programmed.

Note: Subscriber Identification Numbers for Telephones 1 and 2 must be entered, even if they are the same.

"E" Lugs see INDEX

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 21



Enable Communicator-Confidence Test (Location 182)

Program a "4" in Location 182 to enable the Communica-

tor-Confidence Test. This feature checks the telephone line for the presence of a dial tone only in those systems that are programmed to communicate with a central station. Note: Do not arm and disarm the panel just before making this test.

Hold down Key [6] until the sounder starts to pulse. If the line is okay, the pulsing will stop; if not, a steady tone will sound (check phone lines). To silence, hold down Key [9].

Enable Download with Answering Machine (Location 082)

Permits downloading to a telephone with an answering machine (factory programmed). After one ring, the panel will listen for the modem tone produced by the PCI2000. If recognized, the panel will go into line seizure and, if security codes match, establish connection with the PCI2000.

Enable Keypad Auxiliary Panic (Location 082)

This feature may be enabled only if all system keypads are F/P/A-panic compatible. (Cut panic-enabling jumpers in all keypads). Pressing the [B/A] and [#] keys simultaneously will activate Keypad Auxiliary Panic. This is a "report only" feature. Program an Alarm Code in Locations 062-063 and a Group-2 Subscriber ID Number. A successful report will be indicated by a ringback at the keypad. In order to prevent multiple alarms from being transmitted, subsequent AuxiliaryPanic alarms cannot be tripped for five minutes. Also see Keypad Aux. Alarm on NTO Lug.

Enable Keypad Fire Panic (Location 082)

This feature may be enabled only if all keypads in the system have the F/P/A-panic capability. (Cut panic-enabling jumpers in all keypads). Pressing the [9/F] and [#] keys simultaneously will activate Keypad Fire Panic.

Enable Keypad (Police) Panic See Panic Zone

Enable Keypad Sounder on Alarm (Locations 164-165)

Programmable for Zones 1-7 and Keypad Panic. When tripped, a steady tone will sound at the keypad until the panel is disarmed.

Enable Keypad Tactile Beep (Location 181)

Causes the sounder to beep briefly with each press of a button. For RP1000LCD and RP1000eLCD keypads: Cut the keypad tactile-beep jumper to prevent a double beep from sounding.

Exit/Entry Delay (Locations 218-223)

Permits exit and entry through the Exit/Entry Zone(s) (see Locations 202-205) after the system is armed without setting off an immediate alarm. Exit delay allows the user to leave the premises after the panel has been armed. Entry delay allows the user time to enter and disarm the panel. Upon entering, the keypad sounder will emit a steady tone to remind the user to disarm.

Two separately-programmable entry delays are provided to accommodate different entry zones (only one exit delay is provided). If two or more Exit/Entry Zones are entered in succession, the delay programmed for the last Exit/Entry Zone entered will take precedence over all others.

Exit time (Locations 218-219) and entry time (Locations 220-223) may each be programmed for up to 255 seconds (4¼ minutes). See Time Selection. If times are not programmed, exit time will be 60 seconds; entry delay will be 30 seconds. (In UL installations, exit time may not exceed 60

seconds; entry time may not exceed 45 seconds).

Entry delay may be cancelled by holding down Key [4] (Instant Protection) prior to or after arming, however it will be automatically reinstated upon disarming.

Exit Entry Follower (Locations 206, 207)

A zone programmed as an Exit/Entry Follower will ignore detection during the exit delay, and only during entry delay if the Exit/Entry Zone is entered first. Thus, detection devices (passive infrared detectors, for example) along the path between the keypad and the exit/entry door will not signal an alarm during exit/entry delay under normal conditions. However, if a device in the Exit/Entry Follower Zone detects a violation when the exit/entry door has not first been entered, there will be no entry delay and the Exit/Entry Follower Zone will go into an instant alarm.

If the panel is armed with the entry delays cancelled (Instant Protection), any violation on the Exit/Entry Zone or the Exit/Entry Follower Zone will cause an immediate alarm.

Extended Format See Data Format

Failure to Communicate on NTO Lug See Untimed Output

Fault Find See Disable Fault Find

Fire Lug (Lug E9)

Lug E9 (FIRE) will go to about 1VDC when a fire alarm is tripped. E9 may be used to trip an LW-900 Long-Range Wireless Interface. Or, a relay (400Ω minimum) may be connected between E9 and Terminal 5 (+ AUX. POWER) if a diode is wired in series (cathode to E9; anode to relay coil).

Fire Zone (Terminals 11 & 12) Fire on Burg Zone (Locations 306-307)

(Note: Do not use Fire Zones in Mercantile installations). The Fire Zone is indicated by the red FIRE/TROUBLE keypad LED. Normally-open devices are connected across Terminals 11 and 12, in parallel with the 2200Ω end-of-line resistor (see Wiring Diagram). A short across the Fire Zone will cause a fire alarm: the red LED will light and the sounder will pulse; an open circuit (trouble) will cause a blinking red LED and a pulsing sounder after a 10-second delay. The sounder may be silenced using Reset Key [9]. The LED will go off within 30 seconds after reset if the alarm or trouble is cleared. Note: Even if the Fire Zone is not used, the end-of-line resistor must be installed.

For the Fire Zone to report on alarm (Location 168) or to restore (Location 172), program Alarm Codes in Locations 016-017 and Restore Codes in Locations 056-057. Trouble and Restore Trouble on all Fire Zones (including Fire on Burg

Zones, see below) are reported in Locations 020-021 and 060-061, respectively. To reset Fire, program a "2" in Loca-

tion 181 (see Reset Fire Zone).

Any Zone 1-7 may be converted to a Fire Zone by programming it for Fire on Burg Zone, however that zone must be programmed for 24-Hour Protection as well. No other zone feature except Untimed Output may be selected for that zone, however program reporting features as required; Fire alarms will activate a steady siren unless Pulsing Fire Output is programmed. Note: Only 4-wire smokes may be used on zones programmed as Fire on Burg Zone.

When an alarm condition is detected on any Fire Zone, a Fire Alarm Verification feature will cause all zones to power down for 10 seconds. Power is restored and a 4-second

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 22



power-up time is started. Thereafter, the zone will be active again. This represents a total processing time of 14 seconds from the time the alarm is first detected. If an alarm condition still exists or reoccurs within 2 minutes, an alarm will be initiated, otherwise the zone will return to its original state. Note: Alarm restores are sent individually; trouble restores are not sent until all fire troubles are restored.

Force-Arm Report See Closing Report Ground-Start Module, GSM-400 (Lug E3)

If the dial tone is not continuously active, Ground-Start Module Model GSM-400 will be required at Lug E3 to establish the dial tone. For installation, refer to the instructions furnished with the GSM-400.

Group Bypass (Location 196, 197) Chime On with Group Bypass (Location 081)

Group Bypass removes a programmed group of zones from the system. It is often used to deactivate some or all interior zones simultaneously so that the user may move freely throughout the premises but still be protected from intrusion through armed perimeter zones.

Group Bypass is executed by pressing Key [B] twice; the yellow BYPASS LED on the keypad will light. When the panel is subsequently disarmed, all bypassed zones automatically revert to non-bypassed zones. The zones bypassed may be checked by holding down Key [2] (Display Bypass) until the beep sounds and all zones have been displayed.

When a "1" is entered in Location 081 (Watch On with Group Bypass), all Day Zones will be activated simultaneously (Watch Mode) when Group Bypass is activated. See Watch On with Group Bypass.

When a "2" is entered in Location 081 (Chime On with Group Bypass), the Chime Mode will be enabled for all programmed zones when Group Bypass is activated. Note that (a) Group Bypass need not be programmed for any zone to use this feature; (b) if a zone is programmed as a Chime Zone, it may not be programmed for Group Bypass; and (c) if this feature is programmed, Hold-Down Function 5 (Chime On/Off) is disabled. Also see Chime Zone.

Include Manual Bypass in Force-Arm/Status See Closing Report

Key Input on Zone 7 (Location 183)

For a remote arm/disarm keyswitch station, program an "8" in Location 183 and wire a normally-open momentary keyswitch to Zone 7. Supervise the keyswitch with an end-of-line resistor in parallel and program Zone 7 for 24-Hour Protection. This feature reports as User 1.

Keypad Aux. Alarm on NTO Lug See Untimed Output

Keypad Panic See Panic Zone

Line-Reversal Module, M278

The Line-Reversal Module allows the control panel to be monitored by a central station through leased lines. On alarm, the module reverses normal line voltage polarity. For details, see instructions furnished with the module.

Listen-in Lug (Lug E5)

If the installation requires one, connect a Listen-In module to Lug E5. The 12V at Lug E5 will drop to zero when the communicator goes off-hook. The voltage will return when the transmission is completed and the module can occupy the

phone line. Note: A Listen-In Module may not be used in UL installations.

Also see Untimed Output: Audio Verification on NTO.

Loop Response (Locations 214-217)

Loop response is the amount of time that a normally closed circuit must remain open, or a normally-open circuit remain closed, to trip an alarm. The slower the loop response, the more immune the system will be to intermit tents ("swingers"). Selectable loop-response times are:

750mS (.75 sec.): The slowest loop-response time, rec-

ommended for use with magnetic contacts, window foil, etc. Unless programmed otherwise, loop-response time will be .750mS (milliseconds) for all zones.

50mS (.05 sec.): Used for momentary panic buttons and

area protection devices, such as photoelectric eyes, passive infrared sensors, floor mats, etc.

7mS (.007 sec.): An extremely fast loop response used

primarily for window bugs.

Low Battery (Location 169,173) Disable Low-Battery Display (Location 305)

A low-battery alarm will signal a system trouble ("2'" flashing with LED's) when the battery terminal voltage drops below

11.5V (nominal). A low-battery condition may report to a central station by programming a "4" in Location 169. LowBattery restores report upon detection of a specified terminal voltage during a dynamic battery test. See Bell/Battery Test (Hold-Down Function 1).

If Disable Low-Battery Display is programmed, there will be no indication of a low-battery system trouble at the keypad unless accompanied by another system trouble.

Never Arm (Locations 090-091)

A zone programmed as Never-Arm cannot go into alarm. When tripped, it will display at the keypad when Hold-Down Function 3 (Display Status) is selected. A chime will sound at the keypad while armed or disarmed if Chime is programmed for that zone and enabled. (The display will also indicate the zone if Display Chime is programmed). This feature is suggested for use as a garage-door or driveway monitor or similar application.

No AC See AC-Failure Reporting

No End-of-Line Resistor (Locations 088-087)

Program for any normally-closed zone that is not wired with an end-of-line resistor.

No Opening Report After Alarm on Zone 6 (Location 183)

If Opening Report After Alarm is selected and a TM900 Test Timer is installed, wire the TM900 to zone 6. Program a "2" in Location 183. Also see Opening Report After Alarm.

NTO Lug See Untimed Output

Number of Rings See Callback Telephone Number 1, 2

Opening (Closing) Codes See Opening (Closing) Report

Opening Report (Select User(s) Opening) (Location 176) Opening Report After Alarm (Location 179)

Opening and closing reports are generally used in commercial installations. On disarming, the communicator can send an opening code for each user (Select User(s) Open- ing), or it may transmit only when the panel is disarmed

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 23



after an alarm has occurred (Opening Report After

Alarm). Note that Subscriber Identification Numbers

(Locations 108-111; 140-143) and Opening Codes (Locations 070-077) must be entered for either opening report;

Program Select User(s) Opening (Location 176) to report

each time the panel is disarmed. Each of up to four users may have his own Opening Code (Locations 070-077). If selecting Opening Report, do not select Opening Report After Alarm.

Program Opening Report After Alarm ("1" in Location

179) to report only when disarming after an alarm. This feature may be used by the central station to verify that the subscriber has responded to the alarm and disarmed the panel. If Opening Report After Alarm is selected, do not select Opening Report.

Panic Zone Enable Keypad Panic (Location 182)

To enable Panic from the keypad (K/P on Programming

Sheet), program a "2" in Location 182. The Panic Zone is tripped by simultaneously pressing Keys [*] and [#] and may be programmed to send a silent alarm to a central station, activate an audible alarm, or both. (For silent panic, see Direct Keypad Panic to Ambush.) Keypad Panic may be disabled at individual keypads by cutting a jumper on the keypad circuit board. Also see Enable Keypad Auxiliary Panic; Enable Keypad Fire Panic.

Remote momentary pushbutton panic switches (normally open) are connected across the two white wires on the keypad (only on those keypads that support remotepanic switches). In UL systems, remote panic buttons must be located in the same room as the keypad.

PIR Zone (Locations 092, 093) Sensor Watch

(Locations 094-095)

Disable Day-Zone Report (Location 079) Power-Up Delay

Program for any zone containing a PIR or dualtechnology sensor, floor mats, door contacts, etc. Upon powering up the control panel, a 3-4 minute delay on these zones allows sensors to stabilize. For power-up delay only, do not program Sensor-Watch Time (Locations 094-095, see Time Selection). Power-up delay may be cancelled by holding down Reset Key [9] until the function beep sounds.

If no trip is detected within the programmed SensorWatch time, a Day-Zone trouble will be transmitted to the central station, if programmed to report ("8" in Location

158). There is no audible indication at the keypad.

Program Sensor Watch in Locations 094-095. Select a value according to the expected activity within the coverage area while disarmed. In calculating the Sensor Watch time, note that only the disarmed hours (the time between armed periods) are added. In moderate traffic areas, a Sensor Watch time of perhaps 15 hours may be appropriate, whereas in remote areas, a time of 60 hours or more may be in order. Sensor Watch time should be calculated for the PIR Zone with the least amount of traffic. However, if no activity is expected on a zone (in an attic, for example) that zone should not be programmed as a PIR Zone, (if Locations 094-095 are left blank, PIR Zones will still be delayed on power-up, but they will not be monitored for activity).

If this feature is selected and any other zones are pro-

grammed as Day Zones, a "2" may be programmed in Location 079 (Disable Day-Zone Report) to inhibit Day-Zone trouble reports. A Day-Zone condition will still display at the keypad, but a trouble report at the central station will now indicate a PIR-Zone trouble.

Power Up in Last State (Location 180)

If programmed, the panel will return in its last state (armed or disarmed) when AC is restored after a lengthy power failure (and the backup battery is depleted). If the panel returns armed and closings are programmed to report for User 1, it will report as USER 1.

Pre-Dial Delay (Locations 114,146)

A Pre-Dial Delay may be used whenever a delay is required before dialing. It is usually required to program Dial- Tone Detection, which causes the communicator to wait for a dial tone before dialing (see Dial-Tone Detection). Certain telephone exchanges send a nonstandard dial tone that the communicator may not be able to detect. With these nonstandard exchanges, it is possible to program Pre-Dial De- lay rather than Dial-Tone Detection. This will cause the communicator to wait for a predetermined time before dialing rather than look for a nonstandard dial tone.

Contact the telephone-equipment supplier to find out how long a delay is required before dialing. Select Pre-Dial Delay by programming one "D" for each 4-second delay required. Enter Pre-Dial Delay "D"s starting in Location 114 for Telephone 1, and starting in Location 146 if Telephone 2 is used. See Backup Reporting; Double Reporting; Split Reporting. Also see Access Number for Outside Line.

Priority Zone (Locations 190, 191)

A zone that will prevent arming if in trouble. If an attempt is made to arm, the sounder will emit a steady tone and a "P" will be displayed. The priority condition may be silenced by disarming. Any zone may be selected as a Priority Zone. A zone in trouble that is neither a Priority Zone nor an Auto-Bypass Zone will cause an alarm on arming.

Priority Zone with Bypass (Locations 188, 189)

A Priority Zone that will permit arming if the priority condition is bypassed by pressing Reset Key [9], then entering a User Code. The zone will auto-bypass and, if status is reported, the condition can be communicated to a central station.

Any zone not selected as a Priority Zone may be programmed as a Priority Zone with Bypass. When programming a zone as Priority with Bypass, do not program Re- move Auto-Bypass. Also see Display Any Bypass.

Pulsing Fire Output See Alarm Outputs

Receiver Format (Locations 112, 144)

The communicator can transmit to any standard central station receiver. A receiver format must be programmed for each telephone number used, but a different format may be assigned to each.

Refer to Double Reporting and Backup Reporting to determine if Telephone 2 will be programmed. Call the central station for each telephone number to check the type of receiver in use. From Table 5, enter the receiver format for each phone number.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 24



Entry Receiver Format

blank

Ademco, Silent

Knight Slow

Sescoa, Vertex,

2 Radionics Fast 1800 13/12 400

3 Silent Knight Fast 1900 40/30 560

5 Universal Hi-Speed

6 Reserved

DCI, Franklin

Radionics, DCI,

Franklin Slow

Add "8" for 2300Hz Handshake; do not add if 1400Hz Handshake

Table 5. Receiver Formats

Data Freq.

(Hz)

1900 60/40mS 600mS

1800 30/20 800

1800 60/40 600

Duty Cycle

(On/Off)

Interdigit

Time

Program the receiver-format entry in Location 112 for

Telephone 1 and Location 144 for Telephone 2, if used.

Receiver See R1000 Installation Instructions WI604

Remote Status LED on NTO Lug (Location 082)

When a "2" is programmed in Location 082, a remote

Status LED connected to the NTO Lug will go on when the lug is low, giving the same indication as the keypad STATUS LED. In this application, do not use the NTC Lug as an output. Connect the LED cathode to the lug through a 560Ω resistor, and the anode to +12V AUX. POWER (Terminal 5).

Remove Auto-Bypass (Locations 192, 193)

All zones are normally Auto-Bypass Zones and will be bypassed if in trouble when arming. (Note that the exit/ entry door must be closed before arming, otherwise the Exit/Entry Zone will be auto-bypassed). A momentary beep will sound at the keypad to warn that the system has been armed with a zone in trouble. Hint: Remove AutoBypass from Follower Zones containing a keypad and PIR to permit arming while motion is sensed. The zone will be secure by the time exit delay has expired.

Note: If auto-bypass is removed from a zone in trouble that is not programmed for Priority arming (Locations 190, 191), that zone will cause an alarm on arming. If selecting Priority Zone with Bypass, do not select Remove Auto Bypass.

For UL installations, non-24-Hour Zones with auto-

bypass (Remove Auto-Bypass not programmed) must be programmed for Priority Zone with Bypass. If an attempt is made to arm with these zones in trouble, the sounder will come on, a "P" will be displayed, and the panel will not arm (enter a valid arm/disarm code to silence the sounder and clear the display). To arm, hold down Reset Key [9] for about 2 seconds, then enter the arm/disarm code.

Report on Alarm (Locations 166-169)

Violation of a zone selected to report on alarm will cause the communicator to transmit the code selected for that zone to the central station. Enter Alarm Codes (Locations 000-029) for each zone to report on alarm, even if identical codes are used for different zones.

Reset Fire (Location 181)

If detection devices in use require removal of DC voltage to reset, program a "2" in Location 181 and wire the device power leads to Terminals 11(+) and 12(–) for twowire devices, or Terminals 11(+) and 13(–) for four-wire devices (see Wiring Diagram). Holding down Reset Key [9] until the sounder beeps will momentarily remove power from Terminal 11.

Reset Shock Sensors on Arming (Location 305)

Select for detection devices that require a brief power interruption to reset; wire the device power leads to Terminals 11 and 6. Arming the system will momentarily remove power from the Fire Power terminal to reset the device.

Reset Test Timer on Report See Test Timer

Restore Report Restore, Control-Panel (Locations 170-173) Restore, Zone (Locations 184,185)

If programming Zone Restore, Control-Panel Restore must be programmed as well. When selecting a Restore Report, (a) Subscriber Alarm/Restore Identification Numbers must be programmed for Telephone 1 (Locations 100-

107) and Telephone 2 (Locations 132-139), if used; and (b) Restore Codes (Locations 040-069) must be entered for each zone selected to report a restore.

The communicator can transmit a report to the central station when a zone or the control panel is restored. To select the time of reporting, refer to Table 5.

Select User(s) Closing See Closing Report

Program: for Control-Panel Restore to be sent: and for Zone Restore to be sent:

Instant Auto-Reset (Locations 200,

Auto-Reset After Alarm Timeout

(Locations 200, 201; "2"

201)

in Location

180)

(See Note 2) Zone Repaired with Panel

No Auto-Reset When panel is disarmed (regardless of zone condi-

When (a) zone is repaired; or (b) control panel is

When (a) resets (alarm times out & zone repaired);

Note: (1) 24-Hour Zone restores are sent as shown under Zone Restore. (2) It is recommended that Zone-Restore Zones or 24-Hour Zones be programmed with Auto Reset or Priority Zone to prevent accidental auto-bypassing of a latched zone.

MA1008e / 1008eM Installation Instructions

disarmed

or (b) when panel is disarmed.

tion)

Table 6. Restore Reports

When zone is repaired, whether panel is armed or disarmed

When zone resets (alarm times out & zone is repaired) whether panel is

Armed

When panel is disarmed When panel is armed & disarmed

armed or disarmed.

Disarmed

again

L NAPCO Security Systems

Page 25



Select User(s) Opening See Opening Report

Selective Bypass (Locations 194,195)

Removal of one particular zone from the system. Any or all Zones 1-7 programmed for Selective Bypass may be removed from the system, but each must be removed separately.

Selectively bypass a zone by pressing Bypass Key [B] followed by the zone number. The next time the panel is disarmed, all bypassed zones will automatically revert to non-bypassed zones.

When one or more zones is bypassed, the yellow BYPASS LED on the keypad will light. The zones bypassed may be confirmed by holding down Key [2] (Display By- pass) until the function beep sounds; with the key depressed, the bypassed zones will be displayed.

Sensor Watch™ See P/R Zone; Time Selection

Service Code See User 5 Service Code

Single-Digit Format See Data Format

Smoke Detectors (Terminals 11 & 12)

Connect smoke detectors as shown on the Wring Diagram. Note that Terminals 11 and 12 may be used for the Fire Zone only. Up to 10 compatible two-wire smoke detectors may be "daisy-chained" together. Subtract smokedetector alarm current from auxiliary standby current. See COMPATIBLE UL-LISTED DEVICES.

Note: If they are of the self-resetting type, power 4-wire smokes from the Constant Auxiliary Voltage Output at Terminal 5 instead of Terminal 11.

Sounder Output on Lug E4 (Location 180)

When an "8" is programmed in Location 180, Lug E4 will go low whenever the keypad sounder is activated. This feature disables Lug E4 for use as an Arm Lug (see Arm Lug).

Split Reporting (Location 179)

Split Reporting causes all reports except Openings, Closings, and Test Timer to be sent to Telephone No. 1, while Openings, Closings, and Test Timer report to Telephone No. 2. (Split Reporting overrides Backup Reporting or Double Reporting if either combination is programmed). Enter Subscriber ID's (Locations 132-143) and other information (Locations 144-163) required for Telephone 2. Note that Subscriber ID Numbers for Telephones 1 and 2 must be entered, even if they are the same.

Status Report See Closing Report

Subscriber Identification Numbers (Locations 100-111; 132-143)

Different Subscriber Identification Numbers (account numbers) may be used by the central station to distinguish Alarm and Restore Reports (Locations 100-107) from Opening and Closing Reports (Locations 108-111). Similarly, different numbers may be used to distinguish Alarm/ Restore Reports for Group-1 Zones (Zones 1-7) from Group Zones (Fire to Low Battery). Both groups must be programmed, even if both use the same number. See Report on Alarm; Restore Report; Opening Report; Closing Report.

Furthermore, if a second telephone is used, different Subscriber Identification Numbers may be required for Alarm/Restore Reports (Locations 132-139) and Opening/ Closing Reports (Locations 140-143). As above; both

groups must be programmed, even if both use the same number. See Double Reporting; Backup Reporting.

Note:

1. If the central station cannot accept two-digit or extended event codes, the Alarm and Restore Codes may be the same as the Opening and Closing Codes; or, the Alarm/Restore Codes may be the same for Groups 1 and 2 if the respective Subscriber Identification Numbers are different.

2. Starting at the left-most location, enter at least 3 digits for each Subscriber Identification Number, even if the first two are zeros. A fourth digit is available for those receivers capable of recognizing 4-digit subscriber codes.

Sum Check See Data Format

Swinger Shutdown (Locations 084-085)

When programmed, Zones 1 through 7 with Auto-Reset will only reset twice (3 alarms) until rearmed in order to prevent "swingers" (intermittents) from causing repeated false alarms. (Do not program for UL installations). See Auto- Reset.

Telephone Numbers (Locations 117-131; 149-163)

To report to a central station, Telephone Number 1 (Locations 117-131) must be programmed. Telephone Number 2 (Locations 149-163) is programmed if Backup Reporting, Split Reporting or Double Reporting is selected.

Telephone Number 1 will be preceded by at least one

Dial-Tone Detection entry ("E" in Location 116) or Pre-Dial Delay entry ("D" in Location 114) to ensure that the commu-

nicator detects a dial tone or waits a reasonable time to access a telephone line before dialing. (See Dial Tone Detec- tion; Pre-Dial Delay.) Furthermore, private telephone systems may require a separate Dial Tone Detection or PreDial Delay digit, followed by an Access Number (Location

115) to obtain an outside line. (See Access Number for Outside Line).

It should be noted here that Telephone Number 1 need not actually start in Location 117 nor end in Location 131, as extra locations have been provided to allow for additional prefix digits, if required. What is important is that Telephone Number 1, with its associated Pre-Dial Delay, Access Num- ber, and Dial-Tone Detection, be wholly contained within Locations 114-131, and that they be in their proper sequence. It may, in fact, be advantageous to leave one or two blank locations before entering the telephone number to allow for the unexpected (an additional Pre-Dial Delay, for example). The above applies to Telephone Number 2 (Locations 149-163) and the Callback Telephone Number (Locations 270-285; PROM Page-1 Locations 014-029) as well.

Note: An "F" in any location will be ignored by the communicator when dialing.

Test Timer (Locations 024, 025;169) Reset Test Timer on Report (Location 181)

When a "1 " is programmed into Location 169, a daily test report will be transmitted to the central station from the time the panel is powered up. The respective Alarm Code is programmed into Locations 024, 025.

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 26



By entering an "8" in Location 181, the timer will be pro-

grammed to send a daily test only if there has been no other report. (Note that this, or the above, is required in UL installations). Thus, if one normally reports an opening every weekday morning, for example, this feature may be utilized to maintain reporting continuity on weekends.

Test-Timer Offset (Locations 250, 251)

If Test Timer is programmed, the test timer will report immediately upon power-up, and every 24 hours thereafter. To delay the timer reporting time up to 24 hours from power-up time, program Locations 250 and 251 in hours (see Time Selection). (If these locations are left blank, the test timer will report immediately upon power-up).

Timeout (Locations 224-231)

Specifies the length of time that an alarm, alert, or delay will remain active. Abort-Delay time and Burglary timeout must be programmed, or the feature will not activate. See Time Selection.

Note: In installations governed by California Fire Marshal regulations, do not program a timeout for fire alarms.

Time Selection Also see Programming Sheet

The times shown in Table 8 are programmable. The Time Selector Chart on the Programming Sheet shows example times only, in seconds or minutes. In reality, any time up to those shown in Table 8 may be programmed. Note that each time is programmed in two locations. The first location has a time factor of 1, the second a time factor of 16.

Time (t) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Entry * 1 2 3 4 5 6 7 8 9 0 B C D E

*Blank. Note: if both programming locations are left blank, re-

1st box 2nd box

tx1 tx16

fer to Table 8 Notes for feature timeout.

Table 7. Program entries for unit times.

To select a time up to 15 seconds, 15 minutes, or 15 quarter-seconds (3.75 seconds), program the respective entry into the first box only; do not program the second box. To select a time greater than 15 seconds, 15 minutes, or 15 quarter-seconds, program both boxes as follows:

1. For the feature selected, choose an appropriate time in units shown (all seconds, minutes, or quarterseconds -- not minutes and seconds, etc.).

2. Divide the time chosen by 16. Enter the quotient in the 2nd Box and the remainder in the 1st Box.

3. Check entries by adding the contents of the 1st Box to 16 times the contents of the 2nd Box. (Remember that a "zero" entry represents "10").

Example 1. Program Entry Delay 1 for 1½ minutes.

1. Entry Delay 1 (Locations 220, 221) is in units of sec- onds, thus delay time is 90 seconds.

2. Divide by 16: 90/16 = 5 (quotient) + 10 (remainder). Enter the quotient in the 2nd Box and the remainder in the 1st Box:

220 221

remainder

(0 for "10")

0 5

quotient

3. Check entries (remember, a "0" entry = "10"): 10 + 16 (5) = 90.

Example 2. Program the sounder to sound a "Chime"

for 4 seconds.

1. Chime time duration (Locations 230, 231) is in units of

quarter-seconds, thus chime duration is 16 quarterseconds.

2. Divide by 16: 16/16 = 1 (quotient) + 0 (remainder). Enter the quotient in the 2nd Box and the remainder (blank entry for "0") in the 1st Box.

230 231

remainder (blank for "0")

quotient

3. Check entries (blank entry = "0"): 0 + 16(1) = 16.

Sensor-Watch Time (see

Abort Delay (see Note 1) 232, 233 sec. 4 min., 15 sec.

Exit Delay (See Note 2) 218, 219 sec. 4 min., 15 sec.

Entry Delay 1 (See Note 2) 220, 221 sec. 4 min., 15 sec.

Entry Delay 2 (See Note 2) 222, 223 sec. 4 min., 15 sec.

Burglary Timeout (See Notes

Time Locations Units Max. Time

Note 1)

1 & 3)

Fire-Zone Timeout 228, 229 min. Untimed (See

Chime Duration 230, 231 1/4

Timer Offset 250, 251 hr. 23 hr. (See Note

Table 8 (Programmable times and timeouts.

094, 095 hr. 255 hr.

(255 sec.)

224, 225 min. 4 hr., 15 min. (255

sec.

min.)

Note 4)

Untimed (See

Note 4)

Notes:

1. If both locations are left blank, this feature will not activate (timeout = 0).

2. If both locations are left blank, Exit Delay = 60 sec.; Entry Delay = 30 sec.

3. In UL installations, timeout must be at least 4 minutes for Residential; at least 15 minutes for Mercantile.

4. If both locations are left blank, this feature will remain active until system is disarmed. (Chime may be reset using Key [9]; however if a time is programmed, Chime cannot be reset and must time out). If both locations are programmed "F", maximum time = 4 hours, 15 minutes (255 minutes); or 63.75 seconds (255 quarter-seconds) for Chime Duration.

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 27

5. If left blank and Test Timer is selected, will report immediately on power-up.

6. In installations governed by California Fire Marshal regulations, do not program a timeout for fire alarms.

TouchTone® Dialing (Location 178) TouchTone

with Rotary Backup (Location 178)

Select TouchTone Dialing only when the subscriber has TouchTone service. TouchTone dialing is faster than rotary dialing, but not always as reliable.

For the communicator to use TouchTone on all dial attempts, add a "1" to Location 178. To use TouchTone on the first attempt with subsequent rotary dial attempts, add a "2" to Location 178. TouchTone Dialing will override TouchTone

with Rotary Backup if both are selected. Note that if Backup Reporting is also selected, the communicator will use rotary

dial to reach Telephone 2.

Trouble

An abnormal zone condition (a break in a normally closed loop; a short on a normally-open loop; or either on an end-ofline-resistor supervised loop) while disarmed.

Trouble on a Burglary Zone will be indicated by a sounder beep upon arming (does not apply to selective- or groupbypassed zones). If auto-bypass has been removed from a Burglary Zone, that zone will go into alarm on arming. Note that if the zone is Exit/Entry, it will go into alarm after exit-delay and entry-delay times have elapsed.

Trouble (open circuit) on a Day Zone (normally closed) will be indicated by a flashing green STATUS LED and a beeping sounder; the digital readout will display the troubled zone(s). Keypad indications are reset by Key [9].

A Fire-Zone trouble is indicated by the red FIRE/ TROUBLE LED and by the sounder. An open circuit or short to ground on Fire Power (Terminal 11) or Aux. Power (Terminal 5) will cause a flashing LED and a pulsing sounder after a 10-second delay. (A short across the EOL resistor will cause an alarm condition: steady LED and pulsing sounder). Reset Key [9] will silence the sounder; the LED will go out within 30 seconds if the cause of the trouble has been removed. Note: Fire trouble restores are sent only after all zones are restored.

Two-Digit Format See Data Format

Untimed Output (NTO Lug E15; Locations 096-099) Audio Verification on NTO Lug (Location 305) Failure to Communicate on NTO Lug (Location 078) Keypad Aux. Alarm on NTO Lug (Location 079)

Lug E15 is an untamed output, programmable for any zone (Group 1 or Group 2). When tripped, the NTO Lug will go low. This output may be used for strobes (do not exceed 300mA), or to trip an LW-900 Long-Range Wireless Interface. A relay (400Ω minimum) may be connected between E15 and Terminal 5 (+ AUX. POWER) if a diode is inserted in series (cathode to E15; anode to relay coil).

Select Audio Verification on NTO Lug for the MAV-15 Two-Way Voice or other listen-in device. The NTO lug will go low when a programmed zone is tripped but will return high when the central-station communication is complete.

If Failure to Communicate on NTO Lug is programmed ("2" in Location 078), Lug E15 will go low after 9 unsuccessful transmissions, and remain low until either a transmission or a Telco Test is successful.

Page 27



If Keypad Aux. Alarm on NTO Lug is programmed, Lug E15 will go low when the keypad Auxiliary Panic is tripped, and will remain low until the panel is disarmed.

Also see Abort Delay; Remote Status LED on NTO Lug.

User Program Code (Locations 238-243)

Allows an authority to access the User Program Mode to program any User Code (see GETTING UP AND RUNNING - Programming User Codes. The default User Program Code is 1,2,3,4,5,6, however this code must be changed to preserve system security. Enter the 3-to 6-digit User Program Code starting in Location 238.

Note: The Dealer Program Code must not start with the same numbers as the User Program Code.

User 5 Arm Only (Location 078) User 5 Report as User 1 (Location 078) Users 6, 7 & 8 Report as Users 2, 3 & 4 (Location 079) User 5 Service Code (Location 079)

To restrict User Code 5 as an "arm-only" code (for singledigit easy arming), program a "4" in Location 078 (Do not pro- gram User 5 Service Code). Note that if a single-digit armonly code is programmed, the hold-down function for that digit is disabled.

The Service Code is controlled by User 1. Whenever User 1's code is entered, the Service Code is deactivated. To activate, merely arm using the Service Code. (The Service Code can always be used to arm). To enable User Code 5 as a Service Code, program a "1" in Location 079. For the Ser- vice Code to report, it must report as User 1 ("8" in Location

078). For Users 6, 7 and 8 to report, they must report as Users 2, 3 and 4 ("4" in Location 079).

Watch On with Group Bypass (Location 081)

The Watch Mode activates all Day Zones simultaneously. When a "1" is entered in Location 081, the Watch Mode will be enabled when Group Bypass is selected (by pressing Key [B] twice). Note that (a) Group Bypass need not be programmed for any zone for this feature to operate; (b) if a zone is programmed as a Day Zone, it may not be programmed for

Group Bypass; and (c) Chime On with Group Bypass should not be programmed.

Zone Restore See Restore Report

Normally, Control-Panel Restore is programmed for a zone to send a restore report to the central station when either the zone is repaired or the panel is disarmed. If the restore report is to be sent only when the zone is repaired, Zone Re-

store should be selected (also program Control Panel Restore). It is recommended that Auto Reset and Priority Zone

or Priority Zone with Bypass also be selected for proper operation. See Restore Report.

24-Hour Protection (Locations 198, 199)

A zone that provides protection at all times, whether or not the system is armed. Neither the green STATUS nor the red ARMED/ALARM LED will indicate the condition of a zone programmed for 24-Hour Protection, however an alarm will be logged into Alarm History (see Alarm History).

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 28



INDEX

24-HOUR PROTECTION ............. ...................................... 27

ABORT DELAY ............................................................... 17

AC FAILURE ................................................................... 10

ACCESS NUMBER FOR OUTSIDE LINE .............................. 17

ACCESSORIES ............................ ................. ................. ... 4

AC-FAILURE REPORTING ................................................ 17

ACTIVATE FIRE & AUX. PANICS .......................................... 7

ALARM CODES .............................................................. 17

ALARM HISTORY ...................... ...................................... 17

ALARM OUTPUTS .............. ......................................... 3, 17

ALARM RESET ................................................................. 9

AMBUSH CODE .............................................................. 17

AMBUSH ZONE ................................................................ 9

ANTI-JAM TIME .............................................................. 18

ARM LUG ....................................................................... 18

ARMING & DISARMING THE SYSTEM .................................. 9

AUDIBLE TEST ON ARMING ............................................. 18

CHIME ZONE ................................................................. 18

CLOSING REPORT ......................................................... 19

COMMUNICATOR FEATURES ...................................... 4, 14

COMMUNICATOR-CONFIDENCE TEST .......................... 9, 21

COMPATIBLE UL-LISTED DEVICES ..................................... 4

CONTROL-PANEL MOUNTING ............... ............................. 6

CONTROL-PANEL RESTORE ............................................ 19

DATA FORMAT ............................................................... 19

DAY ZONE ......................... ........................... ................. 20

DEALER KEYPAD PROGRAMMING ................................... 11

DEALER PROGRAM CODE ............................................... 20

DEALER PROGRAM MODE .............................................. 11

DEFAULT PROGRAM ........................................................ 8

DIAL-TONE DETECTION .................................................. 20

DIRECT KEYPAD PANIC TO AMBUSH ............... ................. 20

DISABLE BELL TEST ............................ ........................... 20

DISABLE CALLBACK-METHOD DOWNLOAD ....................... 20

AUDIO VERIFICATION ON NTO LUG ................................. . 18

AUTO-BYPASS ZONE ...................................................... 18

AUTO-DOWNLOAD ID NUMBER ........................................ 18

AUTO-RESET ... .............................................................. 18

AUXILIARY PANIC ............................................................. 9

BACKUP REPORTING ..................................................... 18

BATTERY ...................................................................... 18

BATTERY LUG ............................................................... 18

BATTERY TERMINAL VOLTAGE ........................................ 10

BATTERY TEST ....... ......................................................... 9

BELL / BATTERY TEST ...................................................... 9

BURG LUG ..................................................................... 18

BURGLARY OUTPUT .......... ..................................... ........ 18

BURGLARY OUTPUT ON AMBUSH .............................. 17, 18

CALLBACK SELECT ........................................................ 18

CALLBACK TELEPHONE NUMBER 1 ................................. . 18

CALLBACK TELEPHONE NUMBER 2 ................................. . 18

DISABLE DAY-ZONE REPORT .................................... 20, 23

DISABLE DISPLAY BYPASS ............................................. 20

DISABLE FAULT FIND ..................................................... 20

DISABLE FUNCTION-6 DOWNLOAD .................................. 20

DISABLE LOW-BATTERY DISPLAY .......................... .... 20, 22

DISPLAY ......................................................................... 3

DISPLAY ANY BYPASS ................................... ................. 20

DISPLAY DAY ZONES AFTER RESET ................................ 20

DISPLAY OPEN ZONES ................................................... 20

DON'T WAIT FOR HANDSHAKE ........................................ 20

DOUBLE REPORTING ..................................................... 20

DOWNLOAD WITH ANSWERING MACHINE ......................... 21

DOWNLOADING FROM A COMPUTER ............................... 13

ENABLE COMMUNICATOR-CONFIDENCE TEST .................. 21

ENABLE DOWNLOAD WITH ANSWERING MACHINE ............ 21

ENABLE KEYPAD (POLICE) PANIC .................................... 21

ENABLE KEYPAD AUXILIARY PANIC ................................. 21

CENTRAL STATION REPORTING ........................................ 8

CHANGING OR VOIDING A CODE ....................................... 9

CHIME ON WITH GROUP BYPASS ............................... 18, 22

MA1008e / 1008eM Installation Instructions

ENABLE KEYPAD FIRE PANIC .......................................... 21

ENABLE KEYPAD PANIC ................................................. 23

ENABLE KEYPAD SOUNDER ON ALARM ............................ 21

L NAPCO Security Systems

Page 29



ENABLE KEYPAD TACTILE BEEP ..................................... . 21

EXIT ENTRY FOLLOWER ................................................. 21

EXIT/ENTRY DELAY ........................................................ 21

EXTENDED FORMAT ....................................................... 21

FAILURE TO COMMUNICATE ........................................... 10

FAILURE TO COMMUNICATE ON NTO LUG ........................ 21

FAULT FIND ................................ ............................... 9, 21

FEATURES ...................................................................... 3

FIRE INSTALLATIONS ....................................................... 7

FIRE LUG ...................................................................... 21

FIRE PANIC ..................................................................... 9

FIRE ZONE .................................................................... 21

FORCE ARM REPORT ..................................................... 19

FORCE-ARM REPORT .................. ................................... 22

GENERAL DESCRIPTION .............. ..................................... 3

GROUNDING .................................................................... 6

GROUND-START MODULE ............................................... 22

LISTEN-IN LUG ............................................................... 22

LOCAL DOWNLOADING ..................................... .............. 13

LOOP RESPONSE .......................................................... 22

LOSS OF AC POWER ...................................................... 10

LOW BATTERY ......................................................... 10, 22

LUG E14 ........................................................................ 18

LUG E4 ......................................................................... 18

MERCANTILE BELL ..................................... ...................... 7

MERCANTILE REQUIREMENTS .......................................... 5

MOUNTING ................. ........................... .......................... 6

NEVER ARM .................................................................. 22

NO AC .......................................................................... 22

NO END-OF-LINE RESISTOR ............................................ 22

NO OPENING REPORT AFTER ALARM ON ZONE 6 .............. 22

NTO LUG ..................................... .................... .............. 22

NUMBER OF RINGS ......................... ......................... 18, 22

OPENING (CLOSING) CODES ....................... .................... 22

GROUP BYPASS ............................................................. 22

HOLD-DOWN FUNCTIONS ................................................. 3

INCLUDE MANUAL BYPASS IN FORCE-ARM/STATUS .......... 22

INCLUDE MANUAL BYPASS IN FORCE-ARM/STATUS REPORT

................................................................................ 19

INSTALLATION ................................ ................................. 6

JUMPER OPTIONS ........................... .............................. ... 6

KEY INPUT ON ZONE 7 ......................................... ........... 22

KEYPAD AUX. ALARM ON NTO LUG .................................. 22

KEYPAD AUXILIARY PANIC ................................... ........... 21

KEYPAD FIRE PANIC ....................................................... 21

KEYPAD FUNCTIONS ................................. ....................... 3

KEYPAD JUMPER OPTIONS ..................................... .......... 6

KEYPAD MOUNTING ......................................................... 6

KEYPAD OPERATION ....................................... ................. 9

KEYPAD PANIC .......................................................... 9, 22

KEYPAD PROGRAMMING ................................................ 11

KEYPAD SOUNDER ON ALARM ........................................ 21

KEYPAD TACTILE BEEP .................................................. 21

KEYPAD WIRING .............................................................. 6

LINE-REVERSAL MODULE ............................................... 22

OPENING REPORT ......................................................... 22

OPENING REPORT AFTER ALARM .................................... 22

OPTIONAL PERIPHERALS ................................................. 4

ORDERING INFORMATION ................................................ 4

PANIC ZONE ...................... .................................. .......... 23

PANICS ......................... ...................................... ............ 7

PIR ZONE ....................... ............................................ ... 23

POLICE PANIC ................................................................. 9

POWER UP IN LAST STATE ............................................. 23

POWER-UP DELAY ......................................................... 23

POWER-UP SEQUENCE .................................................... 8

PRE-DIAL DELAY ... .................... .................... ................. 23

PRIORITY ZONE .................... ......................................... 23

PRIORITY ZONE WITH BYPASS ........................................ 23

PROGRAM A USER CODE ................................................. 8

PROGRAM OPENING REPORT AFTER ALARM ................... 23

PROGRAMMING OVERVIEW ........................................ 3, 11

PROGRAMMING RECORD SHEETS ....................... 14, 15, 16

PROGRAMMING SHEETS ................................................ 12

PROGRAMMING STEPS .................................................. 12

PROGRAMMING USER CODES .......................................... 8

PROM PROGRAMMING ................................................... 13

L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 30



PULSING FIRE OUTPUT ................................................... 23

RECEIVER ............................... ...................................... 24

RECEIVER FORMAT ........................................................ 23

REMOTE DOWNLOADING .......... ...................................... 13

REMOTE PANIC ............................................................... 6

REMOTE STATUS LED ON NTO LUG ................................. 24

REMOVE AUTO-BYPASS ................................................. 24

REPORT ON ALARM ....................................................... 24

REPORTING FEATURES ................... ................................. 4

RESET FIRE ................................................................... 24

RESET SHOCK SENSORS ON ARMING ................... ........... 24

RESET TEST TIMER ON REPORT ..................................... 24

RESTORE REPORT ......................................................... 24

SELECT USER(S) CLOSING ............................................. 24

SELECT USER(S) OPENING ............................................. 25

SELECTIVE BYPASS ....................................................... 25

SENSOR WATCH ............ .......................................... 23, 25

TIMES & TIMEOUTS ...................... .................................. 16

TOUCHTONE DIALING .................................................... 27

TRANSFERRING MEMORY FROM PROM ........................... 13

TRANSMITTERS .................... ......................................... 27

TROUBLE ............................. ......................................... 27

TWO-DIGIT EVENT CODE FORMAT ................................... 19

TWO-DIGIT FORMAT ....................................................... 27

UL/CUL LISTINGS ............... .............................................. 4

UNTIMED OUTPUT ......................................................... 27

USER 5 ARM ONLY ............................................... .......... 27

USER CODES .................................................................. 8

USER KEYPAD PROGRAMMING ................... ...................... 8

USER PROGRAM CODE .................................................. 27

USER PROGRAM MODE ......... ......................................... 11

WATCH ON WITH GROUP BYPASS ................................... 27

ZONE FEATURES & KEYPAD CODES ................................ 15

ZONE RESTORE ............................................................ 27

SERVICE CODE ........................ .................... .............. 9, 25

SINGLE-DIGIT FORMAT .......................... ......................... 25

SMOKE DETECTORS .............................................. 4, 5, 25

SOUNDER OUTPUT ON LUG E4 ............... ........................ . 25

SOUNDER SIGNALS .......................................................... 4

SPECIFICATIONS ............................................................. 4

SPLIT REPORTING ......................................................... 25

STATUS REPORT ..................................................... 19, 25

SUBSCRIBER IDENTIFICATION NUMBERS ......................... 25

SUM CHECK .................................................................. 25

SUM-CHECK FORMAT ........ ............................................ . 19

SUMMARY OF UL REQUIREMENTS ............................... ...... 5

SWINGER SHUTDOWN .................................................... 25

SYSTEM FEATURES & TIMEOUTS .................................... 16

SYSTEM TROUBLE INDICATIONS ....................................... 9

TAMPER SWITCHES ......................................................... 6

TELEPHONE NUMBERS ................................................... 25

TEST TIMER .................................................................. 25

TESTING THE SYSTEM ................................................... 10

TEST-TIMER OFFSET ................................. ..................... 26

TIME SELECTION ........................................................... 26

TIMEOUT .......................... ........................... .................. 26

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems

Page 31

6. WIRING DIAGRAM

Page 31



L NAPCO Security Systems

MA1008e / 1008eM Installation Instructions

Page 32



NAPCO LIMITED WARRANTY

NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.

This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.

Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within the six months following the end of the warranty period.

IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges.

This warranty contains the entire warranty. It is the sole warranty and any prior agreements or representations, whether oral or written, are either merged herein or are expressly cancelled. NAPCO neither assumes, nor

authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any other warranty or liability concerning its products.

In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation or liability shall arise or grow out of Seller's rendering of technical advice or service in connection with Buyer's order of the goods furnished hereunder.

NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.

Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical or communications disruption, it is possible for the system to fail to perform as expected. NAPCO does not represent that the product/system may not be compromised or circumvented; or that the product or system will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling police or fire department, in order to mitigate the possibilities of harm and/or damage.

NAPCO is not an insurer of either the property or safety of the user's family or employees, and limits its liability for any loss or damage including incidental or consequential damages to NAPCO's original selling price of the product regardless of the cause of such loss or damage.

Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liability for ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.

MA1008e / 1008eM Installation Instructions

L NAPCO Security Systems