NAPCO GEM-TEMP64 Installation Instruction

R

333 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs, [phone]

For Technical Service, [phone]

Publicly traded on NASDAQ Symbol: NSSC

GEM-TEMP64

Temperature Sensor

For use with the

Installation Instructions

GEM-P1664 Control Panel

© NAPCO 2006

GENERAL DESCRIPTION

The GEM-TEMP64 is an indoor/outdoor remote temperature
sensor designed for use with the Napco GEM-P1664 control
panel and the GEM-RP1CAe2 / GEM-K1CA keypads. The
GEM-TEMP64 consists of the sensor module, which is fully
encapsulated in weather resistant potting, and a snap-on du­rable plastic mounting plate. The GEM-TEMP64 temperature
sensor provides potted electronics, digital accuracy, low
power consumption and durability all in a small, easy to install
package. Current Draw: 10mA.

Rear wire
feed hole

(B)

(A)

Securing Tab

Rear Module Cover

Mounting Plate

Front Module Cover

Fig. 1. GEM-TEMP64 Component Parts

MOUNTING THE GEM-TEMP64

Before mounting the temperature sensor, always plan ahead
and determine the route all wires will follow before drilling into
wall mounting surfaces. Install the GEM-TEMP64 as follows:

Determine mounting location. Using the template (page 3)

and a pencil, lightly mark the location of the two mounting
holes and the wire feed hole. Mounting location should
not exceed 300 feet from the control panel.

Route the Sensor Wires. Three wires are needed to con-

nect the GEM-TEMP64 to the control panel. Use #18
AWG gauge wire or larger at a maximum distance of 300
feet from the control panel. Plan the wire run carefully and
determine how these wires will be accessed from behind
the mounting location.

Drill wire feed hole. The Rear Module Cover (see Fig. 1,

above) contains two wire feed holes: A pre-drilled rear
hole (A) and a side hole (B) that is opened by removing
the tab with pliers or similar tool, of used. Minimum size
for the wire feed holes is 1/8", but can be made larger if
necessary. Note: If using the rear wire feed hole, do not
exceed a diameter that can be concealed by the GEM­TEMP64 module. The diameter of the feed hole should
not exceed 1/2" and should be made as small as possible.
Warning: Use caution when drilling holes--there may be

WI1425 4/06

high voltage wiring in wall.

Install the Mounting Plate using two #4 mounting screws

(supplied). Use hardware such as molly bolts, toggle bolts
or other anchoring devices. Drill the smallest hole needed
for the device. Warning: Use caution when drilling holes-

-there may be high voltage wiring in wall.

Install the Rear Module Cover by sliding the rear cover onto

the mounting plate until it clicks in place. To remove,
press in the securing tab and lift cover from mounting
plate.

Route the module wires from behind the mounting location

through the wire feed hole and through the rear module
cover. Splices can be made and concealed within the
module or made outside the module and pushed back into
wall. Use care not to damage the wiring or the mounting
surface. Seal holes with solicoln to prevent moisture from
entering wall.

Install module. Place the GEM-TEMP64 temperature mod-

ule over the mounting base and snap on to secure.

Connect the module wires to the control panel as detailed

in Table 1, below. Note: Do not apply power until all wir­ing is complete.

Table 1: GEM-TEMP64 Wire Connections

GEM-TEMP64

Wire Colors

Red 12V Auxiliary Power or

Black Ground Auxiliary (–) 6

Green Zone 6 (+) 21

GEM-P1664

Terminal Description

12V Remote Power

Terminal Number

GEM-P1664

5

PROGRAMMING THE GEM-P1664 PANEL

See WI1386 for complete programming information for the
GEM-P1664 control panel.

Three addresses must be enabled (either via Quickloader or via
direct address programming) in order for the temperature to be
displayed instead of the date on line 2 of the GEM-RP1CAe2 (or
GEM-K1CA) keypad. enable the following addresses In PCD­Windows Quickloader software or in direct address programming
via the keypad:

1. Keypad Assignment, Temperature Settings tab, Enable
Temperature Display (Address 1668, press option 1)

2. Keypad Assignment, Keypad Features tab, Enable Key-
pad Time/Date Display (Address 1420, press option 7)

3. Keypad Assignment, Keypad Features tab, Enable Set

Time/Date Message (Address 2051, press option 1)

Note: If these three addresses are set and power (AC and bat-

tery) are subsequently removed, they keypad will indicate that
the time and date are lost and will need to be reset. See next
page for PCD-Windows Quickloader screen image.

1

NAPCO LIMITED WARRANTY

NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be
free from manufacturing defects in materials and workmanship for thirty-six
months following the date of manufacture. NAPCO will, within said period, at its
option, repair or replace any product failing to operate correctly without charge to
the original purchaser or user.

This warranty shall not apply to any equipment, or any part thereof, which
has been repaired by others, improperly installed, improperly used, abused,
altered, damaged, subjected to acts of God, or on which any serial numbers
have been altered, defaced or removed. Seller will not be responsible for any
dismantling or reinstallation charges.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS
NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY,
THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES
ON THE PART OF NAPCO.

Any action for breach of warranty, including but not limited to any implied
warranty of merchantability, must be brought within the six months following the
end of the warranty period.

IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR
DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional who installed and
maintains your security system. In order to exercise the warranty, the product
must be returned by the security professional, shipping costs prepaid and
insured to NAPCO. After repair or replacement, NAPCO assumes the cost of
returning products under warranty. NAPCO shall have no obligation under this
warranty, or otherwise, if the product has been repaired by others, improperly
installed, improperly used, abused, altered, damaged, subjected to accident,
nuisance, flood, fire or acts of God, or on which any serial numbers have been
altered, defaced or removed. NAPCO will not be responsible for any
dismantling, reassembly or reinstallation charges.

This warranty contains the entire warranty. It is the sole warranty and any
prior agreements or representations, whether oral or written, are either merged
herein or are expressly canceled. NAPCO neither assumes, nor authorizes any

other person purporting to act on its behalf to modify, to change, or to assume
for it, any other warranty or liability concerning its products.

In no event shall NAPCO be liable for an amount in excess of NAPCO's
original selling price of the product, for any loss or damage, whether direct,
indirect, incidental, consequential, or otherwise arising out of any failure of the
product. Seller's warranty, as hereinabove set forth, shall not be enlarged,
diminished or affected by and no obligation or liability shall arise or grow out of
Seller's rendering of technical advice or service in connection with Buyer's order
of the goods furnished hereunder.

NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY
TESTED WEEKLY.

Warning: Despite frequent testing, and due to, but not limited to, any or all
of the following: criminal tampering, electrical or communications disruption, it is
possible for the system to fail to perform as expected. NAPCO does not
represent that the product/system may not be compromised or circumvented; or
that the product or system will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise; nor that the product or system will in all
cases provide adequate warning or protection. A properly installed and
maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but
it is not insurance or a guarantee that these events will not occur.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A
CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer
should in turn advise the consumer to take any and all precautions for his or her
safety including, but not limited to, fleeing the premises and calling police or fire
department, in order to mitigate the possibilities of harm and/or damage.

NAPCO is not an insurer of either the property or safety of the user's family
or employees, and limits its liability for any loss or damage including incidental or
consequential damages to NAPCO's original selling price of the product
regardless of the cause of such loss or damage.

Some states do not allow limitations on how long an implied warranty lasts
or do not allow the exclusion or limitation of incidental or consequential
damages, or differentiate in their treatment of limitations of liability for ordinary or
gross negligence, so the above limitations or exclusions may not apply to you.
This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.

2