NAIS HP2-AC48V, HP2-AC6V, HP2-DC110V, HP2-DC12V, HP2-DC48V Datasheet

411

HP-RELAYS

10 AMP POWER RELAY

VDE

2c, 3c

mm inch

25

.984

36

1.417

44.5

1.752

FEATURES

• Interchangeable with existing models

• Long life and high reliability

• High contact capacity up to 10 A 250 V AC

• Available with plug-in/solder and quick-connect terminals

SPECIFICATIONS (at 20 ° C 68 ° F)

Contacts

Remarks

* Specifications will vary with foreign standards certification ratings.
*

1

Measurement at same location as "initial breakdown voltage" section

*

2

Detection current; 10 mA

*

3

Excluding contact bounce time

*

4

Half-wave pulse of sine wave: 11ms; detection time: 10 µ s

*

5

Half-wave pulse of sine wave: 6ms

*

6

Detection time: 10 µ s

*

7

Refer to 5. Conditions for operation, transport and storage mentioned in
AMBIENT ENVIRONMENT (Page 61).

Characteristics (at 60 Hz, 20 ° C 68 ° F)

Arrangement 2 Form C 3 Form C 4 Form C
Initial contact resistance, max.

(By voltage drop 6 V DC 1 A)

15 m Ω

Contact material Silver

Silver

alloy

Rating

Nominal switching
capacity

10 A 250 V AC (resistive)

2 Form C 3 Form C 4 Form C
Maximum operating speed 20 cpm
Initial insulation resistance*

1

more than 100 M Ω at 500 V DC

Breakdown
voltage*

2

Between open
contacts

1,000

Vrms

2,000
Vrms

1,000
Vrms

Between contact sets

1,500

Vrms

2,000
Vrms

1,500
Vrms

Between contact and
coil

1,500

Vrms

2,000
Vrms

1,500
Vrms

Operate time*

3

(at nominal voltage)

Approx.

15 ms

Approx. 25 ms

Release time (without diode)*

3

(at nominal voltage)

Approx.

15 ms

Approx. 25 ms

Temperature rise Max. 65 ° C
Shock resistance

Functional*

4

98 m/s

2

{10 G}

Destructive*

5

980 m/s

2

{100 G}

Vibration resistance

Functional*

6

58.8 m/s

2

{6 G}, 10 to 55 Hz

at 1 mm double amplitude

Destructive

117.6 m/s

2

{12 G}, 10 to 55 Hz

at 2 mm double amplitude

Conditions for opera­tion, transport and
storage*

7

(Not freezing and
condensing at low
temperature)

Ambient
temp.

–50 ° C to +40 ° C

–58 ° F to +104 ° F

Humidity 5 to 85% R.H.

Unit weight

Approx.

60g

2.12 oz

Approx.

100g

3.53 oz

Approx.

125g

4.41 oz

LIFE DATA

Contact rating and expected life For AC load type

Note: When the electromagnet or exciting coil (Solenoid, etc.) is the load, the value of motor or lamp load is applicable.

Voltage 125 V AC 250 V AC

Expected life

(min. operations)

Electrical

life

Load Resistive (cos ϕ

]

1) Inductive (cos ϕ

]

0.4) Resistive (cos ϕ

]

1) Inductive (cos ϕ

]

0.4)

Current

— — 10 A 7.5 A 2 × 10

5

10 A 7.5 A 7.5 A 5 A 5 × 10

5

5 A3 A3 A2 A1

×

10

6

1A 0.7 A 0.6 A 0.4 A 2 × 10

6

Mechanical life 1 × 10

7

HP

412

Contact rating and expected life For DC load type

Voltage 24 V DC 125 V DC

Expected life

(min. operations)

Electrical

life

Load Resistive (cos ϕ

]

1) Inductive (cos ϕ

]

0.4) Resistive (cos ϕ

]

1) Inductive (cos ϕ

]

0.4)

Current

—7 A— —2

×

10

5

7.5 A 5 A 0.5 A 0.4 A 5 × 10

5

5 A 3 A 0.3 A 0.2 A 1 × 10

6

1A 0.6 A 0.1 A 0.06 A 2 × 10

6

Mechanical life 1 × 10

7

Life curve

Notes:

1. F or DC inductive loads, use an arc suppress­ing circuit.

2. When used under a DC load operating at
high repetition rate with considerable arcing,
corrosion of the contacts and/or the contact
blades is likely to occur. When using the relay
under conditions of high temperature, humidity
or high repetition rate, it is suggested that the
relay cover be removed to facilitate extended
operation.

10

0

100

200

300

400

500

600

700

800

900

1,000

Load current, A

Operations, ×10

4

125 V AC cosϕ = 1

5

2

5

0

V

A

C

c

o

s

ϕ

=

1

Mechanical life
more than 10,000,000
operations

TYPICAL APPLICATIONS

HP relays enjoy wide use in v arious appli­cations, particularly in automation con­trols and remote controls.
Applications include:
Industrial machinery

Machine tool
Food processing packing machines
Office equipment
Coin operate devices
Home appliances

Transportation
Communication and measuring devices
Amusement devices

ORDERING INFORMATION

Ex. HP 3

Contact arrangement

2: 2 Form C
3: 3 Form C
4: 4 Form C

(Notes) 1. For UL/CSA or VDE recognized types, add suffix UL/CSA or VDE (HP2-TM type VDE application under way)

2. Standard packing Carton: 50 pcs. Case: 200 pcs.

3. UL/CSA approved type is standard.

Nil: Standard plug-in terminal
M: Direct mounting (3 Form C only)
TM: Top mounting (2 Form C only)
L: Lamp wired, standard plug-in terminal

AC 6, 12, 24, 48,
115, 220, 240 V
DC 6, 12, 24, 48,
110 V

Terminal Coil voltage

M AC240V

TYPES AND COIL DATA

1. Standard plug-in terminal type (without lamp wired)

DC TYPES at 20 ° C 68 ° F

Type Part No.

Nominal coil

voltage, V DC

Pick-up

voltage,

V DC (max.)

Drop-out

voltage,

V DC (min.)

Max.

allowable

voltage, V DC

Coil

resistance,

Ω ( ±

10%)

Nominal coil

current, mA

Nominal
operating
power, W

2 Form C

HP2-DC6V 6 4.8 0.9 6.6 25 240 1.5
HP2-DC12V 12 9.6 1.8 13.2 110 109 1.3
HP2-DC24V 24 19.2 3.6 26.4 440 54.5 1.3
HP2-DC48V 48 38.4 7.2 52.8 1,800 26.7 1.3
HP2-DC110V 110 88 16.5 121 7,300 15.0 1.7

3 Form C

HP3-DC6V 6 4.8 0.9 6.6 24 250 1.5
HP3-DC12V 12 9.6 1.8 13.2 100 120 1.4
HP3-DC24V 24 19.2 3.6 26.4 400 60 1.4
HP3-DC48V 48 38.4 7.2 52.8 1,560 31 1.5
HP3-DC110V 110 88 16.5 121 7,450 14.9 1.6

4 Form C

HP4-DC6V 6 4.8 0.9 6.6 22 273 1.6
HP4-DC12V 12 9.6 1.8 13.2 95 127 1.5
HP4-DC24V 24 19.2 3.6 26.4 380 63 1.5
HP4-DC48V 48 38.4 7.2 52.8 1,500 32 1.5
HP4-DC110V 110 88 16.5 121 7,000 15.7 1.7

HP

413

AC TYPE (50/60 Hz) at 60 Hz, 20 ° C 68 ° F

Type Part No.

Nominal coil

voltage, V AC

Pick-up

voltage,

V AC (max.)

Drop-out

voltage,

V AC (min.)

Max.

allowable

voltage, V AC

Inductance, HNominal coil

current, mA

Nominal

operating

power, VA

2 Form C

HP2-AC6V 6 4.8 1.8 6.6 0.049 310 1.9
HP2-AC12V 12 9.6 3.6 13.2 0.190 160 1.9
HP2-AC24V 24 19.2 7.2 26.4 0.776 78 1.9
HP2-AC48V 48 38.4 14.4 52.8 3.106 39 1.9
HP2-AC115V 115 92 34.5 126.5 15.83 18 2.1
HP2-AC220V 220 176 66 242 57.90 9.5 2.1
HP2-AC240V 240 192 72 264 66.26 9.0 2.2

3 Form C

HP3-AC6V 6 4.8 1.8 6.6 0.030 520 3.1
HP3-AC12V 12 9.6 3.6 13.2 0.119 260 3.1
HP3-AC24V 24 19.2 7.2 26.4 0.475 130 3.1
HP3-AC48V 48 38.4 14.4 52.8 1.899 65 3.1
HP3-AC115V 115 92 34.5 126.5 10.36 28.5 3.3
HP3-AC220V 220 176 66 242 39.32 14.2 3.1
HP3-AC240V 240 192 72 264 44.05 13.9 3.3

4 Form C

HP4-AC6V 6 4.8 1.8 6.6 0.019 800 4.8
HP4-AC12V 12 9.6 3.6 13.2 0.077 400 4.8
HP4-AC24V 24 19.2 7.2 26.4 0.309 200 4.8
HP4-AC48V 48 38.4 14.4 52.8 1.292 95 4.6
HP4-AC115V 115 92 34.5 126.5 6.953 42 4.8
HP4-AC220V 220 176 66 242 26.57 21 4.6
HP4-AC240V 240 192 72 264 29.75 20.5 4.9

NOTES

1. The range of coil current for AC relays
is ± 15% (60 Hz). For DC relays it is

±

10% at 20 ° C, 68 ° F.

2. The HP relay will operate in a range
from 80% to 110% of the nominal coil
voltage. It is, however, recommended
that the relay be used in the range of
85% to 110% of the nominal coil volt­age, with the temporary voltage varia­tion taken into consideration.

3. When the operating voltage of AC re-

lays drops below 80% of the nominal
coil voltage, the relay will generate a
considerable amount of heat which is
not recommended for maximum effi­ciency.

4. The coil resistance of DC types is the
measured value of the coil at a temper­ature of 20 ° C 68 ° F. If the coil tempera-
ture changes by ± 1 ° C, the measured
value of the coil resistance should be
increased or decreased by 0.4%.

5. For applications from 220 V to 240 V
DC, connect a resistor in series with
the relay coil. See chart for resistor val­ues.

Voltage 2 Form C 3 Form C 4 Form C

220 V DC

7.3 k Ω
(5 W)

7.45 k Ω
(5 W)

7 k Ω

(5 W)

240 V DC

8.7 k Ω
(5 W)

8.8 k Ω
(5 W)

8.3 k Ω
(5 W)

2. Standard plug-in terminal type (with lamp wired)

DC TYPES at 20 ° C 68 ° F

Type Part No.

Nominal coil

voltage,

V DC

Pick-up

voltage,

V DC (max.)

Drop-out

voltage,

V DC (min.)

Max.

allowable

voltage,

V DC

Coil

resistance,

Ω ( ±

10%)

Nominal coil

current,

mA

Nominal

operating

power,

W

2 Form C

LED

HP2-L-DC6V 6 4.8 0.9 6.6 25 240 1.5
HP2-L-DC12V 12 9.6 1.8 13.2 110 109 1.3
HP2-L-DC24V 24 19.2 3.6 26.4 440 54.5 1.3
HP2-L-DC48V 48 38.4 7.2 52.8 1,800 26.7 1.3

Neon lamp HP2-L-DC110V 110 88 16.5 121 7,300 15.0 1.7

3 Form C

LED

HP3-L-DC6V 6 4.8 0.9 6.6 24 250 1.5
HP3-L-DC12V 12 9.6 1.8 13.2 100 120 1.4
HP3-L-DC24V 24 19.2 3.6 26.4 400 60 1.4
HP3-L-DC48V 48 38.4 7.2 52.8 1,560 31 1.5

Neon lamp HP3-L-DC110V 110 88 16.5 121 7,450 14.9 1.6

4 Form C

LED

HP4-L-DC6V 6 4.8 0.9 6.6 22 273 1.6
HP4-L-DC12V 12 9.6 1.8 13.2 95 127 1.5
HP4-L-DC24V 24 19.2 3.6 26.4 380 63 1.5
HP4-L-DC48V 48 38.4 7.2 52.8 1,500 32 1.5

Neon lamp HP4-L-DC110V 110 88 16.5 121 7,000 15.7 1.7

HP

414

AC TYPE (50/60 Hz) at 60 Hz, 20 ° C 68 ° F

3. Top Mounting (TM) and direct mounting (M) type

DC TYPES at 20 ° C 68 ° F

AC TYPE (50/60 Hz) at 60 Hz, 20 ° C 68 ° F

Type Part No.

Nominal coil

voltage,

V AC

Pick-up
voltage,

V AC (max.)

Drop-out

voltage,

V AC (min.)

Max.

allowable

voltage,

V AC

Inductance,

H

Nominal coil

current,

mA

Nominal

operating

power,

VA

2 Form C

LED

HP2-L-AC6V 6 4.8 1.8 6.6 0.049 310 1.9
HP2-L-AC12V 12 9.6 3.6 13.2 0.190 160 1.9
HP2-L-AC24V 24 19.2 7.2 26.4 0.776 78 1.9

Neon lamp

HP2-L-AC115V 115 92 34.5 126.5 15.83 18 2.1
HP2-L-AC220V 220 176 66 242 57.90 9.5 2.1
HP2-L-AC240V 240 192 72 264 66.26 9.0 2.2

3 Form C

LED

HP3-L-AC6V 6 4.8 1.8 6.6 0.030 520 3.1
HP3-L-AC12V 12 9.6 3.6 13.2 0.119 260 3.1
HP3-L-AC24V 24 19.2 7.2 26.4 0.475 130 3.1

Neon lamp

HP3-L-AC115V 115 92 34.5 126.5 10.36 28.5 3.3
HP3-L-AC220V 220 176 66 242 39.32 14.2 3.1
HP3-L-AC240V 240 192 72 264 44.05 13.9 3.3

4 Form C

LED

HP4-L-AC6V 6 4.8 1.8 6.6 0.019 800 4.8
HP4-L-AC12V 12 9.6 3.6 13.2 0.077 400 4.8
HP4-L-AC24V 24 19.2 7.2 26.4 0.309 200 4.8

Neon lamp

HP4-L-AC115V 115 92 34.5 126.5 6.953 42 4.8
HP4-L-AC220V 220 176 66 242 26.57 21 4.6
HP4-L-AC240V 240 192 72 264 29.75 20.5 4.9

Type Part No.

Nominal coil

voltage,

V DC

Pick-up
voltage,

V DC (max.)

Drop-out

voltage,

V DC (min.)

Max.

allowable

voltage,

V DC

Coil

resistance,

Ω ( ±

10%)

Nominal coil

current,

mA

Nominal

operating

power,

W

2 Form C

Top Mounting Type (TM)

HP2-TM-DC6V 6 4.8 0.9 6.6 25 240 1.5
HP2-TM-DC12V 12 9.6 1.8 13.2 110 109 1.3
HP2-TM-DC24V 24 19.2 3.6 26.4 440 54.5 1.3
HP2-TM-DC48V 48 38.4 7.2 52.8 1,800 26.7 1.3
HP2-TM-DC110V 110 88 16.5 121 7,300 15.0 1.7

3 Form C

Direct Mounting Type (TM)

HP3-M-DC6V 6 4.8 0.9 6.6 24 250 1.5
HP3-M-DC12V 12 9.6 1.8 13.2 100 120 1.4
HP3-M-DC24V 24 19.2 3.6 26.4 400 60 1.4
HP3-M-DC48V 48 38.4 7.2 52.8 1$B!"(J560 31 1.5
HP3-M-DC110V 110 88 16.5 121 7,450 14.9 1.6

Type Part No.

Nominal coil

voltage,

V AC

Pick-up
voltage,

V AC (max.)

Drop-out

voltage,

V AC (min.)

Max.

allowable

voltage,

V AC

Inductance,

H

Nominal coil

current,

mA

Nominal

operating

power,

VA

2 Form C

Top Mounting Type (TM)

HP2-TM-AC6V 6 4.8 1.8 6.6 0.049 310 1.9
HP2-TM-AC12V 12 9.6 3.6 13.2 0.190 160 1.9
HP2-TM-AC24V 24 19.2 7.2 26.4 0.776 78 1.9
HP2-TM-AC48V 48 38.4 14.4 52.8 3.106 39 1.9
HP2-TM-AC115V 115 92 34.5 126.5 15.83 18 2.1
HP2-TM-AC220V 220 176 66 242 57.90 9.5 2.1
HP2-TM-AC240V 240 192 72 264 66.26 9.0 2.2

3 Form C

Direct Mounting Type (M)

HP3-M-AC6V 6 4.8 1.8 6.6 0.030 520 3.1
HP3-M-AC12V 12 9.6 3.6 13.2 0.119 260 3.1
HP3-M-AC24V 24 19.2 7.2 26.4 0.475 130 3.1
HP3-M-AC48V 48 38.4 14.4 52.8 1.899 65 3.1
HP3-M-AC115V 115 92 34.5 126.5 10.36 28.5 3.3
HP3-M-AC220V 220 176 66 242 39.32 14.2 3.1
HP3-M-AC240V 240 192 72 264 44.05 13.9 3.3