Musical Fidelity A-3.2 Integrated Owners manual
MONITOR
A3.2
DUAL MONO INTEGRATED AMPLIFIER
MUSICAL FIDELITY A3.2 DUAL MONO INTEGRATED AMPLIFIER
PHONO TUNER AUX 2
CD AUX 1 TAPE
I.R.R.
POWER
INSTRUCTIONS FOR USE
Thank you for purchasing the Musical Fidelity A3.2 Integrated amplifier.
Used properly and carefully, it should give you many years of outstanding
musical reproduction.
Æsthetically, the A3.2 Integrated amplifier is a perfect match for the
A3.2 CD player and the A3.2 Tuner.
Together, they form one of the finest hi-fi systems available.
Dust regularly with a soft duster or soft brush, but be careful when using
cleaning or polishing agents - they may harm the surface finish.
If you have any questions about your audio system,
please consult your dealer who is there to help and advise.
Issue 1: March 2002
A3.2 Integrated Amplifier Instructions for use Page 1 of 9
SAFETY
INFORMATION
IMPORTANT! (U.K. only)
This unit is supplied in the U.K. with a mains lead fitted with a moulded 13 amp plug.
If, for any reason, you need to cut off this plug, please remove the fuse holder and dispose of
the plug safely, out of reach of children. It must not be plugged into a mains outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance
with the following code:
Green and yellow..............Earth
Blue...............................Neutral
Brown................................Live
WARNING - This appliance must be earthed
As the colours of the wires of the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug
which is marked with the letter E or coloured green or green-and-yellow, or by the earth
symbol:
The wire which is coloured brown must be connected to the terminal which is marked with the
letter L or coloured red.
The wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black.
If connecting to a BS1363 plug, a 13 amp fuse must be used.
WARNING:
The A3.2 is a powerful amplifier and must necessarily supply high voltages
through the loudspeaker terminals. Therefore, to avoid any possibility of an
electric shock DO NOT TOUCHTHE SPEAKER TERMINALS when the unit is
being used. To comply with BSEN60065 safety regulations, the 4mm “banana”
plug holes have been fitted with plastic blanking pieces. Removal of these will
invalidate any electrical safety approval of this product.
WARNING:
Any modifications to this product not expressly approved by Musical Fidelity who
is the party responsible for standards compliance could void the user’s authority to
operate this equipment.
Issue 1: March 2002
A3.2 Integrated Amplifier Instructions for use Page 2 of 9
GENERAL ADVICE
INSTALLATION PRECAUTIONS and USER INFORMATION
Your new A3.2 Integrated amplifier is designed and built to provide trouble-free performance,
but as with all electronic devices it is necessary to observe a few precautions:
Heed all warnings shown on the back of the product.
Only connect the A3.2 Integrated amplifier to a mains outlet having the same voltage as
marked at the back of the unit.
Always ensure that when disconnecting and reconnecting your audio equipment the mains
supply is switched off.
Position the mains lead and signal interconnects where they are not likely to be walked on or
trapped by items placed on them.
Do not use near water, or place water-filled containers on the amplifier, for example, flower
vases or potted plants. If water does spill inside, immediately pull out the mains plug from
the wall socket and inform your dealer, who should then check the unit before further use.
Entry of liquid into the amplifier is dangerous, and may cause electric shock or fire hazard.
Do not place the unit near heat sources such as radiators, direct sunlight or other equipment.
The case of this amplifier can run at high temperatures - operate the unit in a well ventilated
area, and do not touch the cabinet sides or top after periods of use at high output power.
Do not remove covers or try to gain access to the inside. There are no internal user adjust ments. Refer all service work to an authorised Musical Fidelity agent.
NOTE: Unauthorised opening of the equipment will invalidate any warranty claims.
There are fuses inside the A3.2 amplifier. In the unlikely event that one blows, refer the unit to
your audio dealer. Do NOT try to replace the fuse yourself as this will invalidate the warranty.
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing
agents - they may harm the surface finish.
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected
or damaged by lightning. For protection of your audio system during electrical storms, remove
the mains plugs and disconnect any aerial lead.
If after-sales service is required, to help your dealer identify the A3.2 Integrated amplifier
please quote the serial number located on the rear panel of the unit.
RADIO FREQUENCY INTERFERENCE (R.F.I)
This product has been tested to ensure that its operation is not adversely affected by normal
background levels of R.F.I., and that it does not itself generate excessive amounts of interference. However, if a problem persists, please contact your Musical Fidelity agent.
Issue 1: March 2002
A3.2 Integrated Amplifier Instructions for use Page 3 of 9
Loading...