OPERATION AND PARTS MANUAL
Diamond Back
SP2 "STREET-PRO"
SLAB SAW
13HP & 20HP
HONDA GASOLINE ENGINES
SP213H20, SP2S13H20, SP2S20H20
MODEL #
SERIAL #
© COPYRIGHT 2003, MULTIQUIP INC.
Revision #7 (09/08/06)
MULTIQUIP INC
18910 WILMINGTON AVE. 800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244 800-478-1244
FAX: 310-537-3927 FAX: 310-631-5032
E-mail:mq@multiquip.com • www:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
..
. PARTS DEPARTMENT:
..
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
P/N 35101
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX: 310-537-4259
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310-537-1173
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 3
MQ SP2 SLAB SAW — TABLE OF CONTENTS
MQ SP2 STREET PRO SAWS
Proposition 65 Warning ................................................... 2
Here's How To Get Help .................................................. 3
Table Of Contents ........................................................... 4
Parts Ordering Procedures ............................................. 5
Specifications ................................................................. 6
Dimensions ..................................................................... 7
Safety Message Alert Symbols .................................. 8-9
Rules for Safe Operation ......................................... 10-12
Decals .......................................................................... 13
Major Components ....................................................... 14
13 HP Engine Components .......................................... 15
20 HP Engine Components .......................................... 16
General Information ................................................. 17-18
Inspection ................................................................ 19-20
Inspection Blade ........................................................... 21
Inspection Blade Placement ......................................... 22
Inspection-Guards, Covers, and V-Belts ....................... 23
Inspection-V-Belts and Water Tank ............................... 24
Manual Start-up Procedure ...................................... 25-26
Electric Start-up Procedure .......................................... 27
Shutdown Procedures .................................................. 28
Operation ................................................................. 29-32
Maintenance ............................................................ 33-37
13HP Engine Wiring Diagram........................................ 38
20HP Engine Wiring Diagram........................................ 39
Troubleshooting (Engine) ......................................... 40-41
Troubleshooting (Blade) ................................................ 42
Explanation Of Codes In Remarks Column .................. 42
Suggested Spare Parts ................................................ 43
COMPONENT DRAWINGS
Nameplate and Decals ............................................ 44-45
Under Carriage Assembly ........................................ 46-47
Blade Shaft Assembly ............................................. 48-49
Lifting Bale Assembly ............................................. 50-51
Console (Push) Assembly ....................................... 52-53
Console (Self-propelled) Assembly .......................... 54-55
13 HP Engine Mount Assembly .............................. 56-57
20 HP Engine Mount Assembly .............................. 58-59
13 HP Engine Assembly ......................................... 60-61
20 HP Engine Assembly ......................................... 62-63
Pointers And Covers ................................................ 64-65
Water System Assembly ......................................... 66-67
Blade Guard Assembly ............................................ 68-69
Manual Raise and Lower Assy. (20 inch) ................. 70-71
SELF-PROPELLED MODELS ONLSELF-PROPELLED MODELS ONL
SELF-PROPELLED MODELS ONL
SELF-PROPELLED MODELS ONLSELF-PROPELLED MODELS ONL
Battery Assembly .................................................... 72-73
Transmission Engage Lever Assembly.................... 74-75
Hydrostatic Transmission Assembly ........................ 76-77
Hydrostatic Drive Assembly .................................... 78-79
YY
Y
YY
HONDA GX390K1QWT2
GASOLINE ENGINE
Air Cleaner Assembly .............................................. 80-81
Camshaft Assembly ................................................ 82-83
Carburetor Assembly ............................................... 84-85
Control Assembly .................................................... 86-87
Crankcase Cover Assembly .................................... 88-89
Crankshaft Assembly .............................................. 90-91
Cylinder Barrel Assembly ........................................ 92-93
Cylinder Head Assembly ......................................... 94-95
Fan Cover Assembly ............................................... 96-97
Flywheel Assembly ................................................. 98-99
Fuel Tank Assembly ............................................. 100-101
Ignition Coil Assembly ..........................................102-103
Muffler Assembly .................................................104-105
Piston Assembly .................................................. 106-107
Recoil Starter Assembly ...................................... 108-109
Labels ................................................................... 110-111
HONDA GX620TXF2
GASOLINE ENGINE
Air Cleaner Assembly ........................................... 112-113
Camshaft Assembly ............................................. 114-115
Control Assembly .................................................116-117
Control Box........................................................... 118-119
Crankcase Cover Assembly .................................120-121
Crankshaft Assembly ........................................... 122-123
Cylinder Barrel Assembly .....................................124-125
Cylinder Head Assembly ......................................126-127
Fan Cover Assembly ............................................ 128-129
Flywheel Assembly .............................................. 130-131
Ignition Coil Assembly ..........................................132-133
Muffler Assembly .................................................134-135
Piston Assembly .................................................. 136-137
Fuel Tank Assembly ............................................. 138-139
Fuel Pump ............................................................140-141
Carburetor Assembly ............................................ 142-143
Starter Motor Assembly .......................................144-145
Gasket Kit Assembly ........................................... 146-147
Labels ................................................................... 148-149
Terms and Conditions of Sale — Parts...................... 150
PAGE 4 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
Effective: June 1st, 2005
Ordering parts has never been easier!
PARTS ORDERING PROCEDURES
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
■
View Parts Diagrams
■
Order Parts
■
Print Specification Information
Goto www.multiquip.com and click on
Order Par ts
to log in and save!
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Order via Phone:
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
parts@multiquip.com.
To obtain an MQ Account, contact your
District Sales Manager for more information.
internet
Use the
on
Standard orders
complete part numbers.*
Fax
your order in and qualify for a 3% Discount
on
Standard orders
complete part numbers.*
Domestic (US) Dealers Call:
1-800-427-1244
and qualify for a 5% Discount
for all orders which include
for all orders which include
International Customers
their local Multiquip Representatives for
Parts Ordering information.
Note: Discounts Are Subject To Change
Note: Discounts Are Subject To Change
should contact
❒❒
❒
❒❒
❒❒
❒
❒❒
❒❒
❒
❒❒
❒❒
❒
❒❒
❒❒
❒
❒❒
❒❒
❒
❒❒
www.multiquip.com
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 5
When ordering parts, please supply:
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
NOTE
Unless otherwise indicated by customer, all orders are treated as
within 24 hours. We will make every effort to ship
if received prior to 2PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
❒❒
❒
❒❒
Stock Orders
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
■
Priority One
■
Ground
■ Next Day
■
Second/Third Day
Air Shipments
must be noted on fax or web order form.
✓ DHL
✓
Tr u ck
Standard Orders
the same day the order is received,
and will ship
MQ SP2 SLAB SAW — SPECIFICATIONS
SNOITACIFICEPSWAS.1ELBAT
)hsuP(2PS )delleporP-fleS(2PS
waS
)mm(.niyticapaCedalB
)mm(.nihtpeDgnittuC
)mm(.nisleehWtnorF
)mm(.nisleehWraeR
)gk(.sblthgieW
enignE
02H312PS 02H31S2PS 02H02S2PS
)mm805(.ni02
)mm191(.ni5.7
)gk721(.sbl082 )gk721(.sbl082 )gk8.181(.sbl004
PH31adnoH
2TWQ1K093XG
enignEenilosaG
)mm05xmm521(ediW.ni2x.aiD.ni5
)mm05xmm521(ediW.ni2x.aiD.ni8
PH02adnoH
2FXT026XG
enignEenilosaG
SNOITACIFICEPSENIGNE.2ELBAT
ledoMenignE
epyTenignE
ekortSxeroB
ziroH
2TWQ1K093XGadnoH2FXT026XGadnoH
VHOrednilyCelgniSekortS-4delooc-riA
enignEtfahSlatno
)mm46xmm88(.ni5.2x.ni5.3 )mm66x77(ni6.2x
0.3
°09VHOekortS-4delooc-riA
tfahSlatnoziroH;niwT-V
tnemecalpsiD
tuptuOrewoPmumixaM
euqroTmumixaM
deepSeldI
MPRdaoLoNmumixaM
leuFcificepS
noitpmusnoC
yticapaCknaTleuF
acknarC
yticapaCliOes
metsySgnitratS
paGgulPkrapS
renaelCriA
thgieWyrD
)HxWxL(snoisnemiD
).cc983(.ni.uc7.32).cc416(.ni.uc4.73
mpr006,3/PH31mpr006,3/PH02
)pmr005,2(sbl-tf5.91
)mpr005,2(m-gk7.2
mpr051±004,1mpr051±004,1
mpr001±006,3mpr001±006,3
).rh/sretil18.02(.rh/.lag1).
)sretil5.6(snollag27.1)sretil23.8(snollag02.2
)sretil1.1(stnip23.2)sretil05.1(stnip81.3
tratSlioceRtratScirtcelE
7.0-07.0(.ni130.-820. ).mm87.0-07.0(.ni130.-820.
epyTenolcyCtnemelElauD
)gk13(.sbl4.86)
).mm8
.ni4.71x7.71x0.51
)mm344x054x083(
)pmr005,2(sbl-tf5.23
)mpr005,2(m-fgk05.4
rh/sretil/28.5(.rh/.slag45.1
gk24(sbl6.29
.ni8.71x81x3.51
)mm254x754x883(
PAGE 6 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — DIMENSIONS
Figure 1. SP2 Dimensions
SNOISNEMID.3ELBAT
ECNEREFER
RETTEL
A
B
C
D
E
F htdiWxaM ).mm226(.ni5.42
G esaBleehWraeR ).mm604(.ni61
htdiWraBeldnaHxaM ).mm016(.ni42
NOITPIRCSED
)desiarretnioPtnorF&derewolyllufsraBeldnaH(thgieHxaM ).mm419(.ni63
)desiarylluf(thgieHraBeldnaHxaM ).mm6101(.ni04
)desiaryllufretnioPtnorF&sraBeldnaH(htgneLxaM ).mm2901(.ni34
)derewolretnioPtnorF&desiaryllufsraBeldnaH(htgneLxaM ).mm7271(.ni86
SNOISNEMID
)MM(.NI
H esaBleehWtnorF ).mm653(.ni41
)mm8111x267x4911(.ni44x03x74:)HxWxL(noisnemiDdetarC
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 7
MQ SP2 SLAB SAW — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
This Owner's Manual has been
developed to provide complete
NOTE
engine manufacturers instructions for data relative to its safe
operations.
Before using any of the MQ Series Slab Saws, ensure that
the operating individual has read and understands all
instructions in this manual.
instructions for the safe and
efficient operation of the
MQ SP2 Series Slab Saws.
Depending on the power plant you
have selected, please refer to the
HAZARD SYMBOLS
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
Explosive Fuel
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
DANGERDANGER
DANGER
DANGERDANGER
You WILL be
if you DO NOT follow these directions.
WARNINGWARNING
WARNING
WARNINGWARNING
You CAN be KILLED or
you DO NOT follow these directions.
CAUTICAUTI
CAUTION
CAUTICAUTI
You CAN be
these directions.
Potential hazards associated with MQ SP2 Series Slab Saw
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
KILLED
INJURED
if you DO NOT follow
or
SERIOUSLY INJURED
SERIOUSLY INJURED
if
Burn Hazards
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.
Rotating Parts
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts to
prevent injury.
PAGE 8 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
ALWAYS place the ON/OFF switch in the OFF
position, remove key and/or disconnect the
spark plug lead before servicing the engine
or equipment. Ground the lead to prevent
sparks that could ignite a fire.
Over Speed Conditions
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
Guards and Covers In Place
NEVER operate the saw without blade guards
and covers in place. Adhere to safety guidelines
ANSI American National Standards Institute,
OSHA or other applicable local regulations.
Respiratory Hazard
ALWAYS wear approved respiratory
protection.
Sight and Hearing hazard
ALWAYS wear approved eye and hearing
protection.
Equipment Damage Messages
Other important messages are provided throughout this manual
to help prevent damage to your slab saw, other property, or the
surrounding environment.
NOTE
This slab saw, other property, or the
surrounding environment could be
damaged if you DO NOT follow
instructions.
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 9
MQ SP2 SLAB SAW — RULES FOR SAFE OPERATION
RULES FOR SAFE OPERATION
CAUTICAUTI
CAUTION
CAUTICAUTI
Failure to follow instructions in this manual may lead to
serious injury or even death! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used when
operating the MQ SP2 Slab Saw.
SAFETY
zz
z
DO NOT operate or service this
zz
equipment before reading this entire
manual.
zz
z
This equipment should not be operated by persons under
zz
18 years of age.
zz
z
NEVER operate the saw without proper
zz
protective clothing, shatterproof glasses, steeltoed boots and other protective devices
required by the job.
zz
z
NEVER touch the hot exhaust
zz
manifold, muffler or cylinder. Allow
these parts to cool before
servicing the saw.
zz
z
High Temperatures – Allow the engine to cool before
zz
adding fuel or performing service and maintenance
functions. Contact with
burns.
zz
The engine of this saw requires an adequate free flow of
z
zz
cooling air. NEVER operate the saw in any enclosed or
hot!
components can cause serious
narrow area where free flow
of the air is restricted. If the
air flow is restricted it will
cause serious damage to the
saw's engine and may cause
injury to people. Remember
the saw's engine gives off
DEADLY
gas.
carbon monoxide
zz
z
NEVER operate this equipment when not
zz
feeling well due to fatigue, illness or taking
medicine.
zz
z
NEVER operate the saw under the
zz
influence or drugs or alcohol.
zz
z
NEVER use accessories or attachments, which are not
zz
recommended by or Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
zz
z
Manufacturer does not assume responsibility for any
zz
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
zz
z
Whenever necessary, replace nameplate, operation and
zz
safety decals when they become difficult read.
zz
z
ALWAYS check the saw for loosened hardware such as
zz
nuts and bolts before starting.
zz
z
ALWAYS refuel in a well-ventilated area, away from sparks
zz
and open flames.
zz
z
ALWAYS use extreme caution when
zz
working with flammable liquids.
When refueling, STOP the engine and
allow it to cool.
zz
z
NEVER
zz
machine. Fire or explosion could result
from
a
zz
z
NEVER operate the saw in an explosive atmosphere
zz
where fumes are present or near combustible materials.
An explosion or fire could result causing severe
smoke
fuel vapors
hot!
engine.
around or near the
, or if fuel is spilled on
bodily
harm or even death.
zz
z
Topping-off to filler port is dangerous, as it tends to spill
zz
fuel.
zz
z
NEVER use fuel as a cleaning agent.
zz
PAGE 10 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — RULES FOR SAFE OPERATION
General Safety
zz
z
ALWAYS read, understand, and follow procedures in
zz
Operator's Manual before attempting to operate equipment.
zz
z
ALWAYS be sure the operator is familiar with proper safety
zz
precautions and operating techniques before using the saw.
zz
NEVER leave the machine
z
zz
zz
z
Block the unit when leaving or when using on a slope.
zz
zz
z
ALWAYS check to make sure that the operating area is
zz
clear before starting the engine.
zz
z
Maintain this equipment in a safe operating condition at all
zz
times.
zz
z
ALWAYS stop the engine before servicing, adding fuel and
zz
oil.
zz
z
NEVER run the engine without the air filter. Severe engine
zz
damage could occur.
zz
z
ALWAYS service air cleaner frequently to prevent carburetor
zz
malfunction.
zz
z
AVOID wearing jewelry or loose fitting clothing that may
zz
snag on the controls or moving parts, this can cause a serious
injury.
zz
z
ALWAYS keep clear of
zz
the saw is in operation.
zz
z
ALWAYS store equipment properly when it is not being
zz
used. Equipment should be stored in a clean, dry location
out of the reach of children.
zz
z
NEVER use accessories or attachments which are not
zz
recommended by the manufacturer for this equipment.
Damage to the equipment and/or injury to user may result.
zz
z
Keep all inexperienced and unauthorized people away from
zz
the equipment at all times.
unattended
rotating
or
while running.
moving parts
while
Diamond Blade Safety
zz
z
zz
zz
z
zz
zz
z
zz
zz
z
zz
zz
z
zz
zz
z
zz
zz
z
zz
zz
z
zz
Use appropriate steel centered diamond blades
manufactured for use on slab saws.
Examine blade flanges for damage, excessive wear and
cleanliness before mounting blade. Blade should fit snugly
on the shaft and against the inside/outside blade flanges.
Ensure the blade is marked with an operating speed greater
than the blade shaft speed of the saw.
WARNINGWARNING
WARNING
WARNINGWARNING
ALWAYS inspect diamond blades
before each use. The blade should
exhibit no cracks, dings, or flaws in the
steel centered core and/or rim. Center
(arbor) hole must be undamaged and
true.
Only cut the material that is specified by the diamond blade.
Read the specifications of the diamond blade to ensure the
proper tool has been matched to the material being cut.
ALWAYS keep blade guards in place. Exposure of the
diamond blade must not exceed 180 degrees.
Ensure that the diamond blade does not come into contact
with the ground or surface during transportation. DO NOT
drop the diamond blade on ground or surface.
The engine governor is designed to permit maximum engine
speed in a no-load condition. Speeds that exceed this limit
may cause the diamond blade to exceed the maximum safe
allowable speed.
Ensure that the blade is mounted for proper operating
direction.
WARNINGWARNING
WARNING
WARNINGWARNING
ALWAYS check to make sure that the
operating area is clear before starting the
engine.
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 11
MQ SP2 SLAB SAW — RULES FOR SAFE OPERATION
Maintenance Safety
zz
NEVER lubricate components or attempt service on a
z
zz
running machine.
zz
z
ALWAYS allow the machine a proper amount of time to
zz
cool before servicing.
zz
z
Keep the machinery in proper running condition.
zz
zz
Fix damage to the machine immediately and ALWAYS
z
zz
replace broken parts.
zz
z
Dispose of hazardous waste properly. Examples of
zz
potentially hazardous waste are used motor oil, fuel and
fuel filters.
zz
z
DO NOT use food or plastic containers to dispose of
zz
hazardous waste.
Saw Transportation Safety
zz
z
Use appropriate lifting equipment to ensure the safe
zz
movement of the saw.
zz
z
DO NOT use the handle bars and/or front pointer as lifting
zz
points.
zz
z
When transporting of the saw is required, place saw directly
zz
inside towing vehicle truck-bed and tie-down securely.
NEVER tow saw directly behind towing vehicle.
Emergencies
zz
z
ALWAYS know the location of
zz
the nearest
zz
z
ALWAYS know the location of the
zz
nearest
zz
z
In emergencies ALWAYS
zz
phone or
phone numbers of the nearest
fire department
the case of an emergency.
fire extinguisher
first aid kit
.
keep a phone on the job site
. This information will be invaluable in
.
know the location of the nearest
ambulance, doctor
. Also know the
and
zz
z
DO NOT use the saw on slopes or on extremely un-level
zz
surfaces. An engine tipped to extreme angles may cause
oil to gravitate into the cylinder head making the engine
start difficult.
zz
z
NEVER transport the saw with the blade mounted.
zz
PAGE 12 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — DECALS
Machine Safety Decals
The SP2 series slab saws are equipped with a number of safety decals (Figure 2). These decals are provided for operator safety and
maintenance information. The illustration below shows these decals as they appear on the slab saws. Should any of these decals become
unreadable, replacements can be obtained from you dealer. See the "Nameplate and Decals" section for decal placement.
Figure 2. MQ SP2 Slab Saw Decals
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 13
MQ SP2 SLAB SAW — MAJOR COMPONENTS
Figure 3. SP2 Saw Major Components
Figure 3 displays the location of the various operational control
features of the MQ SP2 slab saw. Features are dependent on the
specific model saw selected. The function of each console component
or indicator is explained below:
1. Handle Bars – Used to steer and push the SP2 slab saw
during cutting operations. The handle can be folded down
for transportation.
2. Forward/Reverse Speed Lever – Controls forward and
reverse speeds for self-propelled operation. Provides
positive neutral for engine start. ALWAYS place
transmission engage/disengage lever in the engage
position before setting speed lever (self-propelled models
only).
3. Raise/Lower Crank Handle – Physically orients saw
(raises or lowers) depending on cranking direction (CW or
CCW). Turning the handle
turning the saw counter-clockwise
clockwise
lowers the saw,
raises the saw.
4. Transmission Engage/Disengage Lever – Forward
locking position engages transmission. Rear Locking
position disengages transmission from rear axle and
permits "free wheeling" (self-propelled models only).
5. Water Tank – A 5-gallon capacity water tank provides water
for the saw blade during wet cutting applications.
6. Water ON/OFF Valve – ON position
permits water to flow from source through saw water hose.
OFF position
7. Hydraulic Drive Transmission - Controls the saw's
forward and reverse movement by using the
reverse speed lever
8. Saw Blade Guard –
operations & allows water hoses to be connected to the
cover for wet cutting.
9. Belt Cover – Covers the drive shaft belt, engine pulley
and the hydraulic transmission belt (on self-propelled
models only).
10. Drive-Shaft Pulley Guard – Covers the drive shaft pulley.
11. Rear Wheels – Allows the saw to be rolled across ground.
On self-propelled models, the rear wheels are turned by
the spline gears attached to the hydraulic transmission
system.
12. Pointer Arm – Front pointer wheel assists in straight
tracking. Lifts up for storage and pivots down for use.
13. Lifting Bale Kit – Allows for easy lifting and transporting
the MQ SP2 slab saw.
closes
valve and halts the flow of water.
(Self-propelled units only).
Covers the saw blade during cutting
opens
valve and
forward/
PAGE 14 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — 13HP HONDA ENGINE COMPONENTS
Figure 4. Engine Controls and
INITIAL SERVICING
The engine (Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
Components (Honda GX390K1QWT2)
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
WARNINGWARNING
WARNING
WARNINGWARNING
Adding fuel to the tank should be
accomplished only when the engine is
stopped and has had an opportunity to cool
down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel
residue has been completely wiped up, and the area
surrounding the engine is dry.
2. Throttle Lever – Used to adjust engine RPM speed (lever
SLOW
advanced forward
FAST
).
3. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
4. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
5. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
6. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
, lever back toward operator
7. Spark Plug – Provides spark to the ignition system. Set
8. Muffler – Used to reduce noise and emissions. Engine
Engine components can generate extreme
heat. To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operating. NEVER operate
the engine with the muffler removed.
9. Fuel Tank – Holds unleaded gasoline. For additional
Operating the engine without an air
NOTE
spark plug gap (HONDA) to 0.6 - 0.7 mm (0.028 - 0.031
inch). Clean spark plug once a week.
components can generate extreme heat. To prevent burns,
DO NOT touch these areas while the engine is running or
immediately after operating. NEVER operate the engine with
the muffler removed.
WARNINGWARNING
WARNING
WARNINGWARNING
information refer to engine owner's manual.
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
D
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 15
MQ SP2 SLAB SAW — 20HP HONDA ENGINE COMPONENTS
Figure 5. Engine Controls and
Components (Honda GX620TXF2)
INITIAL SERVICING
The engine (Figure 5) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer's engine
manual for instructions & details of operation and servicing.
1. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
2. Fuel Tank - Holds unleaded gasoline. For additional
information refer to engine owner's manual.
3. Throttle Lever – Controlled by accelerator pedal,
increases or decreases engine RPM.
4. Choke Knob – Used in the starting of a cold engine or in
cold weather conditions. The choke enriches the fuel
mixture.
5. Oil Sensor Switch – This switch monitors the oil level in
the engine crankcase. In the event of low oil, the engine will
be shut down.
6. Oil Filter – Spin-on type, filters oil for contaminants.
7. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.71 - 0.78 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
8. Fuel Filter – Filters fuel for contaminants.
9. Oil Filler Cap – Remove cap to refill or replace oil with
recommended type as listed in Table 3. Make sure cap is
tightened securely. DO NOT over fill.
10. Air Filter – Prevents dirt and other debris from entering the
fuel system. Unsnap air filter cover to gain access to filter
element.
11. Muffler –Used to reduce noise and emissions.
touch the muffler while it is hot! Serious burns can result.
NEVER
Engine components can generate extreme
heat. To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operating. NEVER operate
the engine with the muffler removed.
12. Oil Dip Stick – Remove to check amount and condition of
oil in crankcase.
13. Starter – Starts engine when ignition key is rotated to the
ON position.
14. Oil Drain Plug – Remove to drain crankcase oil.
operate the engine with the muffler removed.
WARNINGWARNING
WARNING
WARNINGWARNING
D
NEVER
PAGE 16 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — GENERAL INFORMATION
Familiarization
The SP2 series
of concrete or asphalt utilizing diamond blades. They have been
engineered for general, industrial and high production flat cutting
applications. The reinforced steel box frame design adds strength
necessary to reduce vibrations while cutting. Minimizing
vibrations enhances the performance of the blade and extends
the life of the saw.
Heavy-duty front and rear axles, sturdy oversized wheels and
industrial undercarriage assembly ensures accurate tracking and
years of reliable use.
Additionally, the general weight-to-strength ration design of the
frame and chassis assembly provides optimum weight
distribution to keep the blade running true in the cut. A rugged
blade shaft bearing assembly ensures minimal flutter and shaft
harmonics providing the most advantageous condition for a
diamond blade at operating speeds.
Power Plants
The SP2 series slab saws are generally classified in the industry
as LOW to MEDIUM horsepower saws. This classification is
particularly useful when selecting the proper diamond blade for
an application.
There are two gasoline engines used with the SP2 series saws:
13 HP Honda GX390K1QWT2
A
cylinder, OVH rated at 3600 RPM and a
GX620TXF2
RPM. Blade rotation is v-belt driven. This is accomplished by
connecting to the output shaft of the engine to an upper drive
pulley. The lower drive pulley (Blade) is then connected to the
upper drive pulley (Engine) by three V-belts. As the engine shaft
rotates, so does the blade.
Refer to the engines Owner's Manual for the specific instructions
regarding engine operation and maintenance practices.
Console
slab saws
are designed for
air-cooled, 4-stroke single
wet
or
dry
cutting
20HP Honda
air-cooled, 4-stroke OVH 90° V-twin rated at 3600
Water System
All saws provide a water direction system to provide cooling
water to the diamond blade. This system consists of: a standard
"garden hose" valve that connects to the water source (via hose)
to the saw, an
The 20-inch blade guard is designed with two 6-inch vinyl water
tubes to direct water to the diamond blade.
Under Carriage System
A jig welded heavy steel gauge under carriage assembly
supports the saw in tracking, pivoting and stabilization. A rear
axle supports two solid rubber cast hub wheels with roller
bearings, grease fittings and locking collars. A front axle supports
two solid rubber cast hub wheels with roller bearings, grease
fittings and locking collars. The assembly pivots about two rocker
blocks with bushings.
Blade Drive System
A rugged blade shaft assembly has been specifically designed
to support the optimum distribution of torque from the engine
shaft to the blade shaft, and to ensure minimal vibratory conditions
on the tips of the shaft.
Balanced engine & blade shaft pulleys are connected to their
respective shafts, 3 V-belts (13HP, 4 V-belts for 20HP models)
connect to the engine pulley to the blade shaft pulley. The blade
shaft is supported by two self-aligning pillow block bearings that
are uniquely positioned on the most outboard portion of the
reinforced frame.
The combination of pulley and blade shaft bearing positioning
ensures minimal vibration & flutter to the ends of the blade shaft.
Water System
The MQ SP2 slab saw comes standard with a 20-inch hinged
two piece, heavy steel gauge blade guard. The blade guard
provides access for vinyl water tubes that supply optimum volume
and dispersal of water for cooling and/or dust suppression.
ON/OFF
console water valve'
An ergonomically designed control console allows the operator
to easily understand and/or operate the adjustable handlebars,
Raise/Lower Crank Handle
disengage lever
self-propelled models, the console also provides forward/reverse
controls.
Manual Raise/Lower System
The SP2 slab saw uses an ACME thread, manual raise/lower
assembly easily raises and lowers the blade and can lock into
position to ensure a constant depth when cutting. See Table 6 for
blade selection with respect to depth of cut.
(Self-propelled models only). Additionally, for
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 17
, and
transmission engage/
NOTE
All MQ series SP2 slab saws are
designed, engineered and
manufactured with strict
adherence to American National
Standards Institute, Inc. (ANSI)
guidelines B7.1 and B7.5
MQ SP2 SLAB SAW — INSPECTION
Before Starting
1. Read safety instructions at the beginning of manual.
2. Clean the saw, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with dry
compressed air.
5. Check fastening nuts and bolts for tightness.
Engine Oil Check
1. To check the engine oil level, place the saw on secure level
ground with the engine stopped, and the diamond blade
removed.
2. Remove the
(Figure 6) and wipe it clean.
filler cap/dipstick
from the engine oil filler hole
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figures 6 and 7), fill to the edge of the
oil filler hole with the recommended oil type (Table 4).
Maximum oil capacity for the Honda GX390 engine is 2.32
pints (1.1 liters) and for the Honda GX620 engine it is 3.18
pints (1.50 liters).
NOTE
Reference manufacturer engine
manual for specific servicing
instructions.
HONDA 13 HP engine shown.
Honda GX390 engine shown
Honda GX620 engine shown
Figure 6. Engine Oil Dipstick (Removal)
Figure 7. Engine Oil Dipstick (Oil Level)
epyTliO.4elbaT
nosaeS erutarepmeT epyTliO
remmuS rehgiHroC°52 03-W01EAS
llaF/gnirpS C°01~C°52 02/03-W01EAS
retniW rewoLroC°0 01-W01EAS
Explosive Fuel
Gasoline Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration.
DO NOT top-off fuel. Wipe up any spilled fuel.
PAGE 18 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — INSPECTION
Hydrostatic Transmission (Self-Propelled models only) -
An EATON® Model 7 hydrostatic transmission (Figure 8)
provides the power for the saw's propulsion system. The
transmission drives a sprocket that directly connects the spline
drive to the rear wheels. The no load forward/reverse speeds
are approximately 80 ft/min.
Figure 8. Hydrostatic Transmission
The transmission is factory filled with approved hydraulic fluid
that has a viscosity equivalent to SAE 20W-20. Should additional
servicing be required, the following hydraulic fluids are
recommended:
z
General Motors Dextron B
z
Ford MM2C-33F
z
Ford M2C-41A
z
International harvester Hy-Tran Fluids
Battery (Self-Propelled models only) - The 12-volt DC battery
(Figure 10) is shipped dry, and will require a proper electrolyte
level for operation.
When servicing of the battery is required perform the following:
z
A face shield and rubber gloves should be worn while
handling and servicing battery's electrolyte.
z
Disconnect battery terminal clamps, and remove the battery
from the saw when servicing is required.
z
DO NOT overfill the battery.
Electrolyte is an acid and must be handled
with caution. Servicing instructions from the
electrolyte manufacturer must ALWAYS be
followed to ensure safety. Serious injury can
result from careless handling and
noncompliance to safety handling instructions.
Figure 10. Battery
WARNINGWARNING
WARNING
WARNINGWARNING
Overfilling the battery may cause the
electrolyte to overflow resulting in corrosion
to nearby components. Immediately wash
off any spilled electrolyte (battery acid).
D
Figure 9. Transmission Reservoir
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT over fill the fluid reservoir (Figure 10). Note the
level marks on the reservoir.
existing oil conditions (A) cold or (B)
operating the saw.
hydraulic fluid may cause the seals to
mechanical damage.
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 19
It is essential to reference the
hot prior to
Overfilling the transmission with
rupture
D
causing
Additionally, when connecting the positive
(+) cable to the battery's positive (+)
terminal post, DO NOT allow contact of the wrench or any
metallic part to come in contact with the battery's negative
(-) terminal post. This may result in an electrical short circuit
or an explosion.
NOTE
Use only
battery. Tap water can
operating life of the battery.
distilled
water in the
reduce
the
MQ SP2 SLAB SAW — INSPECTION -BLADE
4. Directional Arrow – Check to ensure that the blade is
WARNINGWARNING
WARNING
WARNINGWARNING
Failure to thoroughly inspect the diamond blade (Figure 11)
for operational safety could result in damage to the blade,
the saw, and may cause injury to the user or others in the
operating area.
D
oriented properly on the blade shaft for sawing. Reference
the directional arrow in the blade and place it so the direction
of rotation “downcuts” with the turn of the shaft.
5. Diamond Segment or Rim – Ensure there are no cracks,
dings, or missing portions of the diamond segment/rim.
DO NOT
portion of
rims may cause damage to your saw, and injury to the user
or others in the operating area.
6. Specifications – Ensure that the blade specifications, size,
and diameter properly match up to the sawing operation.
Wet blades must have water to act as a coolant. Utilizing a
diamond blade not matched properly to the task may result
in poor performance and/or blade damage.
7. Arbor Hole – It is essential that the arbor hole diameter
properly matches the blade, and that it is free from
distortions. Correct blade flanges (collars) must be used.
The inside face of the flanges must be clean & free of debris.
An out of round arbor condition will cause damage to the
blade and the saw.
use a blade that is missing a segment or a
the rim
. Damaged and/or missing segments/
8. MAX RPM – This RPM reference is the maximum safe
Figure 11. Diamond Blade
1. Drive Pin Hole – A commonly located hole on the diamond
blade core that prevents operational blade slippage
between the inner & outer blade flanges (collars). Inspect
the diameter of the hole to ensure there is no distortion,
and that a snug fit develops between the hole and drive
pin.
2. Stress Relief Holes (Gullets) –
cracks that may have propagated from the slots and/or
gullets. Cracks indicate extreme fatigue failure and if sawing
continues, catastrophic failure will occur.
3. Edge Of The Steel Core – Check the diameter edge for
discoloration (blue oxidation) indicating an overheating
condition caused by insufficient cooling water/air.
Overheating of blades may lead to loss of core tension
and/or increase the possibility for blade failure. Check to
make sure the steel core’s width is uniform about the rim of
the blade, and not succumbing to an “under cutting”
condition brought about by highly abrasive material or
improper under cutting core protection.
Check the steel core for
operating speed for the blade selected. NEVER exceed
the max RPM on the diamond blade. Exceeding the MAX
RPM is dangerous, and may cause poor performance and
may damage the blade.
PAGE 20 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — INSPECTION - BLADE PLACEMENT
3. Blade Nut – Remove the blade nut (4). For reassembly,
NOTE
■
Set the engine ON/OFF switch to the
OFF position.
■
Raise the saw to a high position by
cranking the Raise/Lower handle in a
counterclockwise direction.
■
Use the Blade Nut Wrench & Blade Shaft Locking Wrench
stored on the front section of the console to install the diamond
blade.
■
Reference Figure 12 (Diamond Blade Placement) when
removing or installing the diamond blade.
1. Blade Guard – Raise the front half of the blade guard to
expose the blade shaft nut & outer flange.
The following steps should be
accomplished before placing the
diamond blade on the
blade shaft.
4. Outside Blade Flange (Collar) – Ensure that the flange
5. Blade Pin Hole – Align this hole with the drive pin hole on
6. Diamond Blade – Ensure that the proper blade has been
7. Inner Flange Collar – This flange is fixed upon the blade
DO NOT over tighten the blade nut against the outer flange.
Tighten blade nut approximately 45-50 ft-lbs/62-69 N/m.
face is clean and free of debris and is placed flush against
the diamond blade (7). Check that the drive pin goes through
the blade pin hole (6) and seats properly into the inner
flange (8).
the inner flange collar.
selected for the job. Pay close attention to the directional
arrow on the blade,
counter-clockwise for left-side
of the blade must match the 1" arbor of the blade shaft.
shaft, and is manufactured with a drive pin hole. The inside
surface of the flange must be free of debris and permit a
tight closure on the surface of the blade.
clockwise for right-side
cutting. The arbor hole
cutting,
2. Blade Nut Wrench – Remove the blade nut wrench (3) from
the tool holder and unscrew the blade shaft nut (right-side).
This nut
clockwise
loosens clockwise
.
and
tightens counter-
Figure 12. Diamond Blade Placement
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 21
MQ SP2 SLAB SAW — INSPECTION -GUARDS, COVERS & BELTS
Guards and Covers Check
WARNINGWARNING
WARNING
WARNINGWARNING
NEVER operate the saw without blade
guards and covers (Figures 13, 14 and 15)
in place. DO NOT operate with the front of
the blade guard raised. The blade exposure
cannot exceed 180 degrees during operations. Adhere to
the safety guidelines of the American National standards
Institute (ANSI) B7.1 and B7.5.
Figure 13. Blade Guard
CHECK the following on the
■
Check to ensure the capacity of the blade guard matches the
diameter of your diamond blade.
blade guard
D
:
V-Belts and Covers
NEVER attempt to check the V-belt with the
engine running because severe injury can
occur. Keep fingers, hands, hair and clothing
away from all moving parts.
V-belts Alignment and Tensioning
This slab saw is equipped with 3 premium V-belts (3 for 13HP
models, 4 V-belts for 20HP models) that have been aligned and
tensioned by factory personnel. All V-belts MUST be installed for
proper operation of the saw. Failure to run the saw with less than
the required number of belts may damage the saw or equipment.
Use the following procedure to check the alignment of
V-belts:
CAUTICAUTI
CAUTION
CAUTICAUTI
1. Remove the bolts that secure the V-belt
2.
D
cover (Figure 15) to the saw frame.
Check uniform parallelism (Figure 16) of
V-belts and pulley (sheaves). Use a straight
edge or machinists's square against both
pulleys and adjust both pulleys until
equally aligned.
■
Check that the guard seats firmly upon the bayonet fitting of
the saw frame.
■
Check that the spring tensioned front cover of the guard is
firmly seated with the rear section of the guard, and there are
no gaps.
■
Check the fit of the water hoses in the sides of the blade
guard. NEVER lift the blade guard while cutting.
■
Check that the flood water tubes are clear and open. Test the
water supply for pressure and flow (to both sides of the blade)
before sawing operations.
CHECK the following on the
■
Check that the flange cover seats firmly upon the bayonet
fitting of the saw frame prior to operation.
■
This flange cover is to be in place when cutting from either the
right or left side of the saw.
blade flange cover
:
Figure 15. V-Belt Cover
Figure 14. Blade Flange Cover
PAGE 22 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
Figure 16. V-Belt Parallelism
MQ SP2 SLAB SAW — INSPECTION - BELTS & WATER TANK
3. Check V-belt tension (Figure 17) by using a tensionmeter
(6.0 - 9.0 lbs.) against the inside belt at a mid point between
the two pulleys, or by deflecting the center belt at a mid point
3/8” (10 mm) - 1/2” (13 mm).
Figure 17. V-Belt Tension
4.
DO NOT over or under tension the V-belts. Severe damage
can occur to the saw and engine crank shaft if the belts are
over tensioned. A decrease of power to the blade and poor
performance will result if the belts are under tensioned (loose
on pulleys).
Water Tank
The SP2 Slab Saw is equipped with a removable 5-gallon onboard water tank fitted in the top of the console which can be
connected to the brass hose fitting on the rear of the operators
console (Figure 18).
Before using the water tank, ensure it is filled to capacity and
connected to the hose fitting to provide lubrication during cutting.
An external water source can also be connected to the SP2 for
extended wet cutting operations.
5. If the V-belts becomes worn or loose, replace them by using
the following V-belt part numbers listed in Table 5.
eziSenignEepyTwaSeziSedalB
PH31
enignE
PH02
enignE
hsuP
hcni02)3(25061
leporP-fleS300-30732300-27152
leporP-fleShcnI02)4(79851200-33882100-08232
Figure 18. On-board Water Tank Hose Connection
syelluPdnastleB-V.5elbaT
N/PtleB-V
).ytQ(
enignE
N/PyelluP
100-56632300-27152
tfahSedalB
N/PyelluP
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 23
MQ SP2 SLAB SAW — MANUAL START-UP (13HP HONDA ENGINE)
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT attempt to operate the saw until the Safety, General
Information and Inspection sections have been read and
understood. Depending on engine manufacturer, operating
steps may vary. See engine operating manual.
The following start-up procedure makes reference to a HONDA
13 HP Engine (Manual Start)
WARNINGWARNING
WARNING
WARNINGWARNING
When the engine is running the cutting blade
is ALWAYS
above the surface when maneuvering the
saw. Damage to the blade and/or saw may
occur if the blade strikes the pavement.
1. Ensure the diamond blade has been mounted correctly and
that it is raised above the surface you are about to saw.
spinning
. Raise the blade high
D
NOTE
5. If operating the SP2 in
step and proceed to step 6. Place the
(Figure 21) in the OPEN position. Skip to step 7.
The CLOSED position of the choke
lever enriches the fuel mixture for
starting a COLD engine. The OPEN
position provides the correct fuel
mixture for normal operation after
starting, and for restarting a warm
engine.
cold weather conditions
, skip this
Choke Lever
2. For wet cutting operations, ensure the water tank is filled to
capacity (5 gallons). Connect the water tank hose to the water
system brass fitting on the rear of the console (Figure 18) and
test for adequate water flow to the diamond blade before
operation.
3. Place the
4. Place the
position.
fuel valve lever
Engine ON/
Figure 19. Fuel Valve Lever
(Figure 19) to the ON position.
OFF
switch
(Figure 20) in the ON
6. If operating the SP2 in
Choke Lever
Figure 21. Choke Lever (Open Position)
cold weather conditions
(Figure 22) in the CLOSED position.
Figure 22. Choke Lever (Closed Position)
, place the
CAUTICAUTI
CAUTION
CAUTICAUTI
The engine governor speed has been set at the factory.
Changing the governor speed could damage the blade and/
Figure 20. Engine ON/Off Switch
PAGE 24 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
or the saw.
MQ SP2 SLAB SAW — MANUAL START-UP (13HP HONDA ENGINE)
7. Place the
and SLOW for starting.
engine governor speed is factory set to ensure optimum
blade operating speeds.
8. Grasp the starter grip (Figure 24) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly
and smoothly for starting.
z
throttle lever
Figure 23. Throttle Lever
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT pull the starter rope all the way to the end.
(Figure 23) halfway between FAST
All sawing is done at full throttle. The
9. If the engine has started, slowly return the choke lever
(Figure 22) to the CLOSED position. If the engine has not
started repeat steps 1 through 8.
Before the saw is placed into operation, run the engine for
10.
several minutes. Check for fuel leaks, and noises that would
associate with a loose guard and/or covers.
11. All sawing is done at full throttle. Your engine governor has
been set at the factory to ensure an optimum speed setting.
z
DO NOT release the starter rope after pulling. Allow it
to rewind as soon as possible.
Figure 24. Starter Grip
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 25
MQ SP2 SLAB SAW — ELECTRIC START-UP (20HP HONDA ENGINE)
The CLOSED position of the choke
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT attempt to operate the saw until the Safety, General
Information and Inspection sections have been read and
understood. Depending on engine manufacturer, operating
steps may vary. See engine operating manual.
NOTE
lever enriches the fuel mixture for
starting a COLD engine. The OPEN
position provides the correct fuel
mixture for normal operation after
starting, and for restarting a warm
engine.
The following start-up procedure makes reference to a HONDA
20 HP Engine (Electric Start)
1. Ensure the diamond blade has been mounted correctly and
that it is raised above the surface you are about to saw.
2. For wet cutting operations, ensure the water tank is filled to
capacity (5 gallons). Connect the water tank hose to the water
system brass fitting on the rear of the console (Figure 18) and
test for adequate water flow to the diamond blade before
operation.
3. If operating the SP2 slab saw in
skip this step and proceed to step 4. Place the
(Figure 25) in the
OPEN
cold weather conditions
Choke Lever
position. Skip to step 5.
The engine governor speed has been set at the factory.
Changing the governor speed could damage the blade and/
or the saw.
5. Place the
and SLOW for starting.
,
6. Place the
position.
CAUTICAUTI
CAUTION
CAUTICAUTI
throttle lever
Figure 27. Throttle Lever (Fast Position)
Engine ON/OFF switch
(Figure 27) halfway between FAST
(Figure 28) in the ON
Figure 25. Choke Lever (Open Position)
4. If operating the SP2 in
Choke Lever
Figure 26. Choke Lever (Closed Position)
(Figure 22) in the CLOSED position.
PAGE 26 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
cold weather conditions
, place the
Figure 28. Ignition Switch (Start Position)
7. If the engine has started, slowly return the choke lever
(Figure 26) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
8. Before the saw is placed into operation, place the
in the FAST position and run the engine for several
lever
minutes. Check for fuel leaks, and noises that would associate with a loose guard and/or covers.
9. All cutting is done at FULL THROTTLE. Your engine governor has been set at the factory to ensure an optimum speed
setting.
throttle
MQ SP2 SLAB SAW — SHUT-DOWN PROCEDURES
Stopping the Engine (13 HP Honda Engine)
WARNINGWARNING
WARNING
WARNINGWARNING
NEVER stop the engine while the blade is in the cut, except for
extreme emergencies. A sudden stoppage of the engine at high
speed while in a cut could damage the blade and/or saw, and
may cause injury to the user or other in the operating area.
1. Place the
lever
(Self propelled models only).
Figure 29. Speed Lever
(Neutral Position)
2. Place the
position, and listen for the engine speed to decrease.
forward/reverse speed
in the NEUTRAL position
engine throttle lever
(Figure 30) in the SLOW
Stopping the Engine (20 HP Honda Engine)
1. Place the
2. Place the
3. Turn the
forward/reverse speed lever
position (Self propelled models only).
engine throttle lever
position, and listen for the engine speed to decrease.
Figure 33. Throttle Lever (Slow Position)
engine ON/OFF switch
position.
(Figure 33) in the SLOW
in the NEUTRAL
(Figure 34) to the OFF
Figure 30. Throttle Lever
2. Turn the console
OFF position.
Figure 31. Engine ON/Off Switch (Off Position)
Place the fuel valve lever (Figure 32) to the OFF position.
3.
Figure 32. Fuel Valve Lever (Off Position)
engine ON/OFF switch
(Figure 31) to the
Figure 34. Ignition Switch (OFF Position)
Emergency Stop Procedure
1. Turn the console
OFF position.
engine ON/OFF switch
(Figure 34) to the
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 27
MQ SP2 SLAB SAW — OPERATION
Adjusting the Blade Height
CAUTICAUTI
CAUTION
CAUTICAUTI
NEVER stop the engine while cutting at high speeds, except for
extreme emergencies. This can damage your SP2 Saw.
The SP2 saw uses a manual
on the console with clockwise rotation providing lowering action,
and counter-clockwise rotation providing raising and lowering
action (Figure 37).
raise/lower crank handle
located
Adjusting the Handle Bars
The SP2 has adjustable height handle bars. Before operating
the saw, adjust the handle bar height to a comfortable working
position:
1. Loosen the height adjustment bolts (Figure 35) on the handle
bars until the handle bars can freely pivot.
Figure 35. Handle Bar Adjustment Bolts
2. Move the handle bars (Figure 36) up or down to operators
desired preference.
To adjust the blade height:
1. Pull upward on the raise/lower crank handle knob.
2. Rotate the crank handle clockwise to
Rotate the crank handle counter-clockwise to
blade
blade has been fully raised or lowered.
NOTE
lower the blade
(Figure 37). The handle will stop rotating when the
Figure 37. Blade Height Adjustment
When moving the saw around
between cutting, fully raise the
blade to avoid striking the ground
with the blade.
.
raise the
Determining the Cut Depth
When preparing to cut, your blade size determines the depth
of the cut. See Table 6 to determine the proper blade size for
Figure 36. Handle Bar Height Adjustment
3. Tighten the height adjustment bolts to secure the handle bars
in place.
CAUTICAUTI
CAUTION
CAUTICAUTI
To avoid losing control of the SP2 slab saw, be sure to fully
tighten the adjustment bolts before operating the saw to prevent
the bolts from loosening during cutting.
PAGE 28 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
your required cutting depth.
edalBdnomaiD
).nI(retemaiD
"21 "8/5-3
"41 "8/5-4
"61 "8/5-5
"81 "8/5-6
"02 "8/5-7
NOITCELESEDALB.6ELBAT
tuCfohtpeD
MQ SP2 SLAB SAW — OPERATION
Traveling During Cutting (Push)
Push models of the SP2 saw must be manually moved by the
operator during cutting operations. Ensure that the handlebars
are secured in place on the console and push against them with
a controlled amount of force to prevent losing control of the
machine.
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT force the blade into the cut any faster than its
designed tendency is effective cut and remove material. This
can damage your blade and/or your machine.
Traveling During Cutting (Self-Propelled)
Self-propelled models of the SP2 saw have a hydrostatic transmission which mechanically propels the saw during cutting
operations. To prepare the machine for self-propelled cutting:
1. Place the
travel lever
in the NEUTRAL position.
3. Move the
increase forward travel speed during cutting (Figure 40).
Placing the travel lever fully forward will move the saw at
maximum speed.
Figure 40. Transmission Engage/Disengage Lever
4. When reverse movement is required, move the
towards the REVERSE position (Figure 41). Placing the
travel lever fully in reverse will move the saw backwards at its
maximum reverse speed.
travel lever
towards the FORWARD position to
(Forward Position)
travel lever
Figure 38. Transmission Engage/Disengage Lever
(Neutral Position)
2. Lift the
located on the console (Figure 39). Leaving the lever down
disengages the transmission to allow for manual pushing
during cutting or moving the machine around the job site.
Figure 39. Transmission Engage/Disengage Lever
transmission
(Engage Position)
engage/disengage lever,
Figure 41. Transmission Engage/Disengage Lever
(Reverse Position)
Saw Alignment
1.
The SP2 saw employs a front pointer (Figure 42) that has
been precisely aligned with the diamond blade at the factory.
Referencing the figure below, accurate tracking is accomplished by referencing the front pointer tip over the cut line.
Precise saw direction is accomplished by slight operator
pressure against the handle bars.
Figure 42. Saw Pointer
To reorient a pointer position, loosen the screw that secures
2.
the pointer bar to the shaft, adjust as necessary, and retighten
the screw.
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 29
Cutting
WARNINGWARNING
WARNING
WARNINGWARNING
The operator MUST wear
the appropriate protective
equipment and clothing while engaged in sawing. Failure
to do so can result in SERIOUS INJURY.
MQ SP2 SLAB SAW — OPERATION
DANGERDANGER
DANGER
DANGERDANGER
DO NOT operate this machine without
the Blade Guard or V-belt Guards in
place. While the blade is spinning, DO
NOT place hands, feet, or other body
parts near the blade to avoid
SERIOUS INJURY or DEATH.
When cutting, determine the required cutting depth and use an
appropriately sized blade. Deep sawing is wasteful to the life of
the blade.
The preferred method of sawing is to
2” (51 mm). Step Cutting provides the optimum opportunity for the
blade to cut fast and last longest.
Wet Cutting Operation
1. Connect hose from water source (on-board water tank or
external water source) to the hose fitting connection
(Figure 3) of the saw. The source pressure should be
approximately 30-40 psi.
2. Ensure the vinyl water tubes are properly inserted into the
blade guard holes and are clear of any obstructions.
3. Turn water source on (Figure 43).
Step Cut
in increments of
5. Align the saw along the cut line utilizing the front pointer.
ALWAYS saw in a straight line only. SERIOUS DAMAGE to
the blade or saw may occur if the saw is twisted or forced to
cut radius shapes.
6. Slowly lower the diamond blade onto the cut line by cranking
Raise/Lower handle
the
the handle can no longer be turned, the blade will be at its full
rated depth.
If the water supply to your blade is interrupted, STOP cutting
immediately
and/or saw.
If the engine stalls for ANY reason during cutting, raise the
blade out of the cut before restarting.
7. For self-propelled models, follow steps 1-4 of the Traveling
During Cutting (Self-Propelled) section.
For push models, use the Traveling During Cutting (Push)
instructions.
Figure 44. Water System ON/OFF Valve
CAUTICAUTI
CAUTION
CAUTICAUTI
CLOCKWISE (Figure 37). When
WARNINGWARNING
WARNING
WARNINGWARNING
to prevent damage to your blade
Figure 43. On-board Water Tank ON/OFF Valve
4. Open the
by moving the lever to the ON position (Figure 44) and ensure
the water is flowing equally to both sides of the diamond
blade.
water system valve
PAGE 30 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
on the left side of the console
8. The rotation of the blade creates a tendency for the saw to
slightly pull in a particular direction. To ensure a straight line
of sawing, apply pressure against the appropriate side of
the handle bar as you slowly advance the saw forward.
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT force the blade into the cut any faster than its design
will allow. This can damage your blade and/or your machine.
Dry Cutting Operation
When dry cutting, follow steps 5-8 of the Wet Cutting Operation
section.
MQ SP2 SLAB SAW — OPERATION
Finishing A Cut
1. Raise the blade out of the cut by cranking the
handle
blade high enough out of the cut to clear the surface and allow
the saw to be maneuvered.
2. Move the engine throttle lever to the idle (SLOW) position
(Figure 30, 33).
3. Set the engine ON/OFF switch to the OFF position (Figure
31, 34).
4. Place the water valve (Figure 44) in the OFF position (as
required).
Engine components can generate
EXTREME heat.
COUNTER-CLOCKWISE (Figure 37). Raise the
WARNINGWARNING
WARNING
WARNINGWARNING
Raise/Lower
Diamond Blades
Diamond blade sawing consists of cutting WET (using water to
cool the blade) or DRY (using the circulating air to cool the blade).
Selecting the diamond blade TYPE and GRADE defines how
the blade will perform both in cutting speed and blade life.
Selection of the proper diamond blade consists of:
z
Determining WET or DRY cutting
z
Material to be Cut
z
Type of Saw Being Used
z
Horsepower of Saw
z
Hardness Characteristics of the Material
z
Performance Expectations
Factors for sawing economy:
z
Type of Blade
z
Depth of Cut
z
Sawing Speed
z
Characteristics of the Material Being Cut
z
Wet or Dry Sawing
Blade Speed
A diamond blade’s performance is directly connected to specific
peripheral (rim) speeds.
The following shaft rotational speeds have been factory set to
ensure optimum blade performance.
z
SP2 20” Capacity - 2,800 RPM.
WARNINGWARNING
WARNING
WARNINGWARNING
Operating saw blades at rotational speeds
greater than those specified by the manufacture can cause blade damage, and may
injure the user or others in the operating
area.
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 31
MQ SP2 SLAB SAW — MAINTENANCE
Maintenance
WARNINGWARNING
WARNING
WARNINGWARNING
General maintenance practices are crucial to the
performance and longevity of your saw. The extreme
environments of sawing operations require routine
cleaning, lubrication, belt tensioning, and inspection for
wear and damage
The following procedures devoted to maintenance can prevent serious saw damage
or malfunctioning. Before servicing or inspection, ALWAYS park the saw on a level
surface with the blade removed, and the
Console Engine ON/OFF switch & Engine
ON/OFF switch in “OFF” position.
Some maintenance operations may require the engine to be run. Ensure that
the maintenance area is well ventilated.
Exhaust contains poisonous carbon monoxide gas that can cause of unconsciousness and may result in DEATH.
General Cleanliness
Engine air filter:
Engine tank & strainer:
Fuel line:
Spark plug:
Bearing Lubrication Care
There are four grease points for the SP2 saw. [Use only Premium
Lithium 12 based Grease, conforming to NLG1 Grade #2
consistency.]
Rear Wheels (1):
Blade Shaft Bearings (2):
Raise/Lower Adjust Tube (1):
Clean air filter 2 to 3 times daily when DRY cutting. See
Engine Owner’s Manual for detailed information.
Clean every year/or 300 hours.
Replace every two years/or as necessary.
Clean/adjust every 6 months/or 100 hours. Replace every
year/ or 300 hours.
Grease daily, see Undercarriage Assy., item 10
Grease daily, see Blade Shaft Assy., item 15
Grease daily, see Raise/Lower Assy., item 2
Clean the machine daily. Remove all dust and slurry build up. If
the saw is steam cleaned, ensure that lubrication is accomplished
AFTER steam cleaning operations.
General Engine Care
Engine check:
Check daily for any oil and/or fuel leakage, thread nut & bolt
tightness, and overall cleanliness.
Engine oil:
Check daily. Inspect with blade removed and saw frame
level on a level surface. Keep the oil clean, and at the proper
servicing level (Figure 8). DO NOT OVERFILL! SAE 10W30 of SG is recommended for general use.
Engine oil change:
Change engine oil the first month or 20 hours of operation.
Then every 3 months/or 50 HOURS of operation. See Engine
Owner’s Manual for detailed information.
ALWAYS dispose of used oil in a
responsible manner. Ensure that
NOTE
the disposition of all hazardous
waste is handled properly. Call
your Recycling Center for
information about recycling engine
oil.
NOTE
When cutting DRY, lubricate blade
shaft bearings 2 to 3 times daily.
The grease can provide an added
protective seal for the bearings.
PAGE 32 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — MAINTENANCE
General Transmission Care (Self-Propelled Models only)
All SP2 model saws utilize spline gear wheel design coupled
with an EATON Model 7 Hydrostatic Transmission that provides
forward/reverse propulsion. The simple design of the system
keeps maintenance to a minimum.
Transmission Reservoir Cup:
Check every 8 hours of operation. When the transmission
cold
is
Figure 45).
DO NOT use multiple viscosity oils! DO NOT OVERFILL.
(A), check oil level against the level indicator (see
CAUTIONCAUTION
CAUTION
CAUTIONCAUTION
Spline Gear Wheels:
Check every 25 hours and clean as necessary. If the spline
wheels DO NOT engage the
pressure, slippage of the rear wheels may occur.
To adjust the
1. Place the
DISENGAGE position (Figure 46) .
Figure 46. Transmission Engage/Disengage Lever
rear wheels
Spline Gear Assembly
transmission engage/disengage lever
(Disengage Position)
with sufficient
:
in the
3. Loosen the linkage adjustment nut and slightly lengthen the
linkage rod (see Transmission Engage Lever Assy., items 11
Figure 45. Transmission Reservoir
Servicing:
The transmission reservoir is factory filled. Should servicing
be required, use SAE20W-20, API classification (SE,CC,CD)
or better, General Motors Dexron B, Ford M2C-33F, M2C41A or International Harvester Hy-Tran fluids. For extreme
hot weather
of SAE30W-30 or SAE40W-40.
Drive Chain:
Check every 50 hours. Periodically wipe the chain clean and
re-lubricate with penetrating chain oil.
The drive chain may stretch requiring tension adjustments.
To adjust the drive chain tension:
1. Loosen the (3) transmission attachment screws (Hydrostatic.
Transmission Assy., item 2)
2. Pivot the transmission in the
mount
Transmission Assy., item 7).
, drain oil and refill with an oil having a viscosity
“U” slots
until the proper tension is achieved (Hydrostatic
of the
transmission
and 13).
4. Move the
ENGAGE position to observe the proper spline-to-rear wheel
contact.
5. Retighten the adjustment nut.
transmission engage/disengage lever
to the
NOTE
Excessive tension on the drive chain
will reduce chain life.
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 33
MQ SP2 SLAB SAW — MAINTENANCE
Drive V-Belt Check
The V-Belts of the SP2 slab saw have been factory set utilizing
precision standards. Operating the saw with less than the
specified number of V-belts (See Table 5), or belts that are
slipping
performance of the saw, and may cause damage to the blade.
Drive V-Belt(s) Replacement & Tension Adjustments
Reference Pointers and Covers Assembly, Blade Shaft Assembly,
and Engine Mount Assembly for this operation.
1. Remove the
2. Loosen the (4) 1-1/2” HHC screws (Engine Mount Assy.,
3. Loosen and back-off the
4. Pivot the Engine Base Plate to provide slack in the Drive V-
5. Remove/Replace the required V-belts (See Table 5).
6. Rotate the engine back into place and tighten the Engine
7. Adjust for the correct V-belt tension (See Figure 47).
or are over-tensioned will significantly diminish the
Belt Guard
15), then loosen the tension of the V-Belts
item 5).
(Pointers and Covers Assy., item
Engine Mount Carriage Bolt
(Engine Mount Assy., item 1) from the frame to permit the
Engine Base Plate
belts.
Mount Carriage Bolt.
(Engine Mount Assy., item 9) to pivot.
Adjust V-Belt Alignment/Replacement Pulleys
The V-belts and their respective pulleys have been professionally
aligned at the factory. If there is a requirement to remove/replace
or adjust the pulleys, proceed with the following instructions.
1. Select the proper sized pulley both in outside diameter and
arbor size. Use approved parts to ensure the compo-
nent compatibility.
2. A change in Pulley diameters may require specifically sized
V-Belts. Contact Multiquip Service Department to en-
sure V-Belt compatibility.
3. Complete Drive V-Belt(s) Replacement steps (1 through 4)
3. Remove the V-Belts from around the Pulley(s).
4. Remove the set screws that secure the pulleys to the respective shafts (PTO shaft) for engine pulley or the (blade shaft)
for the blade shaft pulley.
5. Remove/replace the pulley by sliding it off the shaft.
6. Reorient the new pulley on the shaft, and ensure precise
pulley alignment by utilizing an accurate straight edge (see
Figures 48 and 49).
7. Replace/tighten set screws treated with a drop of
Threadlocker 266.
8. Orient the proper replacement V-Belt(s) around the blade
shaft pulley and engine pulley.
LOCTITE
Figure 47. V-Belt Adjustment/Tension
8. Retighten the (4) 1-1/2” HHC screws.
9. Replace all guards and covers.
WARNINGWARNING
WARNING
WARNINGWARNING
NEVER attempt to check the
V-belt with the engine running.
Severe injury can occur if your
hand gets caught between the
V-belt and the clutch. Always use
safety gloves.
CLUTCH
PULLEY
9. Reference steps 6-9 of the Drive V-Belt(s) Replacement
steps.
Figure 48. Pulley Alignment
VIBRATOR
PULLEY
Figure 49. V-Belt Alignment
PAGE 34 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — MAINTENANCE
Blade Shaft Bearing Replacement
The SP2 slab saw is supported by “tapped base lock collar (w/
set screw)" self-aligning
and 52). These heavy duty bearings support the 1-1/4 blade
shaft, and have grease (zerk) points conveniently located for
service.
1. It is recommended to replace both left & right bearings at the
same time.
2. Follow steps 1 thru 4 of Drive V-Belt(s) Replacement &
Tension Adjustments.
3. Remove Drive V-belts.
Blade Shaft Bearings
(Figures 51
Reference Figure 50 & Figure 51 for steps 4-9
4. Remove
Outside/Inside Blade Flanges
5. Loosen
(Figure 51, item 5) off the Blade Shaft. Loosen Bearing set
screw, remove
Blade Shaft Bearing
6. Loosen
Bolt
(Figure 50, item 6) off the blade shaft.
7. Replace
Shaft Assembly.
8. Re-tension Drive V-belts as shown in the Drive V-Belt(s)
Replacement & Tension Adjustments section.
10. Replace all guards and covers.
Blade Hex Nuts
set screws
Bearing Bolt
set screws
(Figure 50, item 4) and slide the
Blade Shaft Bearings
(Figures 50 & 51, item 1) and
(Figures 50, item 2 & 3)
(Figure 51, item 4) and slide
(Figure 51, item 6) and slide the
(Figure 51, item 8) off the blade shaft.
(Figure 50, item 5), remove
Blade Shaft Bearing
and reassemble the Blade
Pulley
Bearing
Figure 50. Blade Side Bearing (Right Side)
Figure 51. Pulley Side Bearing (Left Side)
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 35
MQ SP2 SLAB SAW — MAINTENANCE
Battery Maintenance
Mishandling of the battery shortens the service life of the battery
and adds to maintenance cost. When handling the battery do the
following:
z
Be careful not to let the battery electrolyte come in contact
with your body or clothing.
z
Always wear
the battery contains sulfuric acid which burns skin and eats
through clothing.
z
Always check the battery terminals periodically to
ensure that they are in good condition.
z
Use wire brush or sand paper to clean the battery
terminals.
z
Always check battery for cracks or any other damage.
If white pattern appears inside the battery or paste
has accumulated at the bottom, replace the battery.
z
If the pump will not be in operation for a long period
of time, store in cool dry place and check the battery
charge level every month to maintain the performance
of the battery.
eye protection
and
rubber gloves
, since
z
Check the battery regularly and make sure that each
electrolyte level is to the bottom of the vent well
(Figure 43). If necessary add only distilled water in a
well-ventilated area.
Figure 43. Battery Electrolyte Levels
WARNINGWARNING
WARNING
WARNINGWARNING
Wear
safety glasses
clothes, and rubber gloves when working with
battery.
or
face mask
, protective
PAGE 36 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — 13HP ENGINE WIRING DIAGRAM (RECOIL START)
Figure 52. 13HP Honda Engine Wiring Diagram
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 37
MQ SP2 SLAB SAW — 20HP ENG. WIRING DIAGRAM (ELECTRIC START)
Figure 52. 20HP Honda Engine Wiring Diagram
PAGE 38 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown,
please take a remedial action following the diagnosis based on the Engine Troubleshooting (Table 7) information shown below and
on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult our company's business
office or service plant.
GNITOOHSELBUORTENIGNE.7ELBAT
NOTPMYSESUACELBISSOPNOITULOS
?gnigdirbgulpkrapS
."gulpkrapstaKRAPS
uciffiD
ontub,elbaliavasileuf",tratsottluciffiD
?noitalusni
?detrohs
?evitcefedliocnoitingI.liocnoitingiecalpeR
dna,elbaliavasileuf",tratsottluciffiD
."gulpkrapsehttatneserpsiKRAPS
kraps,elbaliavasileuf",tratsottl
"lamronsinoisserpmocdnatneserpsi
psreporpmI
?gnitiucric
?epytleufgnorW
?gulpkrapsnotisopednobraC .gulpkrapsecalperronaelC
ifedoteudtiucrictrohS
?paggulpkrapsreporpmI.pagreporp
?metsysleufnitsudroretaW.metsysleufhsulF
gulpkrapstneic
sihctiwsFFO/NOenigneroelosnoC
?yrtridstniop,pagkra
trohsronrownoitalusniresnednoC
?gnitiucrictrohsronekorberiwgulpkrapS
otteS
.hctiws
.stniopnaelc
.gniriw
ronoitalusni,pagkcehC
.gulpkrapsecalper
,noitalusnigulpkrapskcehC
.nrowfiecalper
ecalper,gniriwhctiwskcehC
dnapagkrapstcerrocteS
.resnednocecalpeR
gulpkrapsevitcefedecalpeR
ecalperdna,metsysleufhsulF
.leuffoepyttcerrochtiw
?ytridrenaelcriA .renaelcriaecalperronaelC
?dedurtorprokcutsevlavtsuahxe/noitcuS.sevlavtaes-eR
?nro
wrednilycro/dnagnirnotsiP
",tratsottluciffiD
.roterubractatneserpleufoN
kraps,elbaliavasileuf
"wolsinoisserpmocdnatneserpsi
it
?ylreporpdenethg
?degamad
nseodkcocleuF
?deggolcretlifleuF.retlifleufecalp
?enilleufniriA.enilleufdeelB
tongulpkrapsro/dnadaehrednilyC
teksaggulpkrapsro/dnateksagdaeH
?knatleufnielbaliavatonleuF .leuffoepyttcerrochtiwlliF
?ylreporpnepoto
?deggolcelohrehtaerbpacknatleuF .packnatleufecalperronaelC
.notsip
.gulpkraps
.
steksag
eR
rodnasgnirnotsipecalpeR
dnastlobdaehrednilyceuqroT
gulpkrapsdnadaehecalpeR
leufnesoolottnacirbulylppA
.yrassecenfiecalper,revelkcoc
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 39
MQ SP2 SLAB SAW — TROUBLESHOOTING (ENGINE)
)DEUNITNOC(GNITOOHSELBUORTENIGNE.7ELBAT
NOTPMYSESUACELBISSOPNOITULOS
?naelctonrenaelcriA renael
sinoisserpmoc"rewopnikaeW"
.erifsimtonseoddnareporp
feD .gulpkrapsecalperronaelC
niretaW
sinoisserpmoc"rewopnikaeW"
.serifsimtubreporp
.staehrevoenignE
eepslanoitatoR
.setautculfd
?gulpkrapsytriD .gulpkrapsecalperronaelC
fedliocnoitingI.liocnoitingiecalpeR
?ytridsnifgnilooC.snifgniloocnaelC
?roterubracnilevelreporpmI
?gulpkrapSevitce
?gulpkrapSevitcefeD
?metsysleuf
?evitce
?reporpmieulavtaehgulpkrapS
?leuffoepyttcerroC leuffoepyttcerrochtiwecalpeR
?yltcerrocdetsujdaronrevoG.ronrevogtsujdA
?evitcefedgnirpsronrevoG.gnirpsronrevogecalpeR
.rotaerubrac
.gulpkraps
criaecalperronaelC
dliub-er,tnemtsujdataolfkcehC
ecalperdna,metsysleufhsulF
.leuffoepyttcerrochtiw
foepyttcerrochtiwecalpeR
etcirtserwolfleuF
?d
ahcemlioceR
.noitcnuflamretratslioceR
?trid
?esoolgnirpslairpS.gnirpslairpsecalpeR
dnatsudhtiwdeggolcmsin
.sgolcroskael
.retawdna
PAGE 40 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
rofmetsysleuferitnekcehC
paoshtiwylbmessaliocernaelC
MQ SP2 SLAB SAW — TROUBLESHOOTING (BLADE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown,
please take a remedial action following the diagnosis based on the Blade Troubleshooting (Table 8) information shown below and
on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult our company's business
office or service plant.
GNITOOHSELBUORTEDALB.8ELBAT
NOTPMYSESUACELBISSOPNOITULOS
gnieblairetamehtrofdrahootedalB
.tuc
foesuacebdehsinimideugroTenignE
.stleB-Vesool
llits,gnittucspotSroswolsedalB
.edalbnosniamer
ro/dnathgiartstuctonseodedalB
.eurt
.gnittuc
.rewopenignEtneciffusnI .rewopserohenignEkcehC.gnitteselttorhTkcehC
.tucgnieblairetam
.segnalfdnasredluohs
.noitatorfonoitceridreporpmI
.tfahsedalbehtnognippilssiedalB
.wasdengilasimnodesugniebedalB
ehtrofdrahylevissecxesiedalB
.MPRreporpmitadesugniebedalB
robranodetnuomylreporpmiedalB
elihwedalbotdeilppaecrofevissecxE
.ytirgetni
.noitamrofni
.tfahs
uqitluMrorelaeDtlusnoC
.edalbeht"sserdeR"ot)kcolbrednic
.stleB-Vecalperro/dnanethgiT
..gniwasotecapydaets/wols
yrT.edalbtcerrocrofpi
,kcirbacilis,enotsdnas(lairetamtfosyrevgnittuc
lanoitatordna,detneirosiedalbehttahtkcehC
.noitcerid"gnittuC-nwoD"anistniopworra
ylreporpsinipegnalf&edalbehttahtkcehC
.)01erugiFees(tfahsedalbehtnodellatsni
tnemngiladnasgniraebtfahsedalbkcehC
ehthtiwedalbehtfosnoitacificepskcehC
rofpiuqitluMrorelaeDtlusnoC.tucgnieblairetam
deepsetunimrepteefecafrusedalberusnE
.)92egaPees(000,6yletamixorppasi)MPFS(
edalbehtnodexiffaylreporpsiedalberusnE
aylppA.tucehtniedalbehtecroftonoD
gnieblairetamehtrofdrahootedalB
.tuc
robranodetnuomylreporpmiedalB
.segnalfdnasredluohs
gniloochguonegniviecertonedalB
rolocsidedalB
.ylevissecxegniraew
ro/dnagnilkcarc,gni
.riaroretaw
dnuorfotuoelohrobA
lairetamrofnesohcedalbtcerrocnI
.tucgnieb
elihwedalbotdeilppaecrofevissecxE
.gnittuc
eDtlusnoC
.edalbeht"sserdeR"ot)kcolbrednic
.sirbedfo
.edalbgnittucyrdatuobadetalucricsi
.tfahs
rorelaeDtlusnoC.tucgnieblairetam
.noitamrofnirofpiuqitlum
.gniwasotecapydaets/wols
yrT.edalbtcerrocrofpiuqitluMrorela
,kcirbacilis,enotsdnas(lairetamtfosyrevgnittuc
edalbehtnodexiffaylreporpsiedalberusnE
eerf&naelcerasegnalfedalbehterusnE.tfahs
dedivorpsiretawfoemulov&wolfreporperusnE
riagnilooctneciffuserusnE.sedalbgnittuctewrof
edalbehtnodexiffaylreporpsiedalberusnE
ehthtiwedalbehtfosnoitacificepskcehC
aylppA.tucehtniedalbehtecroftonoD
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 41
MQ SP2 SLAB SAW — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial number
range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model number
or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column,
>
, belong to the same assembly or kit.
NOTE
The contents of this parts catalog
are subject to change without
notice.
*
, #, +, %, or
NOTE
If more than one of the same
reference number is listed, the last
one listed indicates newest (or
latest) part available.
PAGE 42 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — SUGGESTED SPARE PARTS
SP2 SLAB SAW
(13HP PUSH)
1 to 3 Units
Qty. ..... P/N ..................... Description
3 .......... 16052 ................. V-BELTS, DRIVE
1 .......... 29013-001 .......... WRENCH, BOX END 1-1/2 IN.
1 .......... 60087 ................. ROPE, FRONT POINTER 1/4 IN.
2 .......... 15081 ................. GRIPS, HANDLE BAR 1 IN.
1 .......... 06922-003 .......... BLADE SHAFT NUT, RIGHT SIDE
1 .......... 07038-016 .......... BLADE SHAFT NUT, LEFT SIDE
1 .......... 26928-002 .......... OUTER BLADE FLANGE
3 .......... 17210ZE3505 .... ELEMENT, AIR CLEANER
3 .......... 9807956846 ....... SPARK PLUG
1 .......... 17620ZH7023 .... CAP, FUEL TANK
1 .......... 28462ZV7003 .... ROPE, RECOIL STARTER
SP2 SLAB SAW
(20HP SELF-PROPELLED)
Qty. ..... P/N .................... Description
3 .......... 16052 ................V-BELTS, DRIVE
1 .......... 07055-051 ......... V-BELTS, TRANSMISSION
1 .......... 29013-001 ......... WRENCH, BOX END 1-1/2 IN.
1 .......... 60087 ................ROPE, FRONT POINTER 1/4 IN.
2 .......... 15081 ................GRIPS, HANDLE BAR 1 IN.
1 .......... 06922-003 ......... BLADE SHAFT NUT, RIGHT SIDE
1 .......... 07038-016 ......... BLADE SHAFT NUT, LEFT SIDE
1 .......... 26928-002 ......... OUTER BLADE FLANGE
3 .......... 17210ZE3505 ... ELEMENT, AIR CLEANER
3 .......... 9807956846 ...... SPARK PLUG
1 .......... 17620ZH7023 ...CAP, FUEL TANK
1 .......... 28462ZV7003 ... ROPE, RECOIL STARTER
1 to 3 Units
Qty. ..... P/N ........................ Description
3 .......... 15897 .................... V-BELTS, DRIVE
1 .......... 07055-051 ............. V-BELTS, TRANSMISSION
1 .......... 29013-001 ............. WRENCH, BOX END 1-1/2 IN.
1 .......... 60087 .................... ROPE, FRONT POINTER 1/4 IN.
2 .......... 15081 .................... GRIPS, HANDLE BAR 1 IN.
1 .......... 06922-003 ............. BLADE SHAFT NUT, RIGHT
1 .......... 07038-016 ............. BLADE SHAFT NUT, LEFT
1 .......... 26928-002 ............. OUTER BLADE FLANGE
3 .......... 17210759013 ........ ELEMENT, AIR CLEANER
3 .......... 1540090H305PE ... OIL FILTER
3 .......... 9807956846 .......... SPARK PLUG
1 .......... 15229 .................... CAP, FUEL TANK
1 .......... 28462ZV7003 ....... ROPE, RECOIL STARTER
SP2 SLAB SAW
(13HP SELF-PROPELLED)
1 to 3 Units
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 43
NAME PLATE AND DECALS.
MQ SP2 SLAB SAW — NAME PLATE AND DECALS
PAGE 44 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO PART NO PART NAME QTY. REMARKS
1 25782 DECAL, MQ DIAMONDBACK 4
2 23596-001 DECAL, RECOMMENDED MAINTENANCE 1
3 25784 DECAL, SP2 2
4 NAMEPLATE ................................................................... 1 ......... CONTACT MQ PARTS DEPT.
5 28853-001 DECAL, FORWARD/REVERSE LEVER 1
6 20525 DECAL, PROP. 65 1
7 22122-001 DECAL, SERIOUS INJURY WARNING 1
8 25491 DECAL, CW ROTATION 1
9 35137 DECAL, READ 1
10 25260-001 DECAL, KEEP FEET CLEAR WARNING 1
11 25249-001 DECAL, KEEP HANDS CLEAR WARNING 1
12 13118 DECAL, POWDER COATED 1
13 23330-001 DECAL, BELT GUARD CAUTION 2
A 11246 DECAL, BELT DRIVE 1
B 11246 DECAL, CHECK OIL LEVEL 1
C 11246 DECAL, HOT 1
D 11246 DECAL, LUBRICATION 2
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 45
UNDER CARRIAGE ASSY.
MQ SP2 SLAB SAW — UNDER CARRIAGE ASSY.
PAGE 46 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — UNDER CARRIAGE ASSY.
UNDERCARRIAGE ASSY.
NO PART NO PART NAME QTY. REMARKS
1 28777-352 FRAME ASSY. 16”/18”/20” 1
2 28781-002 AXLE, REAR & FRONT 1
3 28782-351 FRAME, UNDERCARRIAGEE ASSY. 1
4 28086-001 WHEEL, 8 X 2 .75 ROLLER BEARING REAR 2
5 28085-001 WHEEL, 5 X 2 .75 ROLLER BEARING FRONT 2
6 8151 WASHER, FLAT SAE 3/4 8
7 10065-090 BEARING PLAIN 2
8 25181-001 COLLAR, SET 0.75 X 1.50 X .50, SPLIT 4
9 8081 PIN, CLEVIS 1/2 X 2-3/4 1
10 0447 WASHER, FLAT SAE 1/2 4
11 3216 PIN, COTTER 1/8D X 1 1
12 0685 SCREW, SHS 5/16-18 X 5/16 2
13 2621 ZERK, GREASE STR. 1/4-28 1
14 1162 A CAP, ZERK FITTING 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 47
BLADE SHAFT ASSY.
MQ SP2 SLAB SAW — BLADE SHAFT ASSY.
PAGE 48 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — BLADE SHAFT ASSY.
BLADE SHAFT ASSY.
NO PART NO PART NAME QTY. REMARKS
1 28807-002 SPINDLE, BLADE 1
2 28081-001 BEARING, PILLOW BLOCK 1.25ID AS206-20 2
3 28811-002 FLANGE, BLADE INSIDE 4.0OD X 1.0ID 1
4 26928-002 FLANGE, BLADE OUTSIDE 1.0ID X5.0OD X 56 1
26928-004 FLANGE, BLADE OUTSIDE 1.0ID X4.0OD X 56 1
5 0125 KEY, WOODRUFF #15 1
6 6059 B KEY, 1/4”SQ. X 2”, 1018 STOCK 1
7 06922-003 NUT, HEX JAM LH 1-14 PLATED 1
8 06502-012 SCREW, HHC 7/16-14 X 1-1/2 4
9 2955 WASHER, LOCK 7/16 ZINC 4
10 0448 WASHER, FLAT SAE 7/16 4
11 25172-003 PULLEY, BLADE SHAFT, 3F3V33X112 .................... 1 ......... 13 HP PUSH & 20 IN.
............................................................................................... SELF-PROP. MODELS
11 23280-001 PULLEY, BLADE SHAFT, 43V4.12 ........................... 1 ......... 20 IN. SELF-PROP. MODELS
12 1528 SCREW, SHS 2
13 28841-001 BUSHING, SPLIT TYPE 1
14 0424 SCREW, 1/4-20 X 1-1/4 3
15 2621 ZERK FITTING 2
16 1162 A CAP,GREASE ZERK, #2 RED 2
17 16052 V-BELT, 3V x 335 ...................................................... 3 ......... 13 HP PUSH &
............................................................................................... SELF-PROP. MODELS
17 15897 V-BELT, 3V x 355 4
18 23250-002 SPACER, SPINDLE 1
19 07038-016 NUT, HEX JAM 1”-14 PLATED 1
20 15046 PIN, DOWEL 3/8 x 1-1/4 LG 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 49
LIFTING BALE ASSY.
MQ SP2 SLAB SAW — LIFTING BALE ASSY.
PAGE 50 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — LIFTING BALE ASSY.
LIFTING BALE ASSY.
NO PART NO PART NAME QTY. REMARKS
1 28890-351 13HP, LIFT BALE ASSY. 1
1 28890-352 20HP, LIFT BAIL ASSY. 1
2 28893-001 BRACE, 13HP BAIL 1
2 28893-002 BRACE, 20HP BAIL 1
3 0205 SCREW, HHC 3/8-16 X 1.0 2
4 10133 NUT, NYLOC 3/8-16 2
5 10136 WASHER, FLAT SAE 3/8 4
6 5283 NUT, NYLOC 5/16-18 2
7 0300 B WASHER, FLAT SAE 5/16 4
8 0202 SCREW, HHC 5/16-18 X 1 ZINC 2
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 51
MQ SP2 SLAB SAW — CONSOLE ASSY. (PUSH MODELS)
CONSOLE ASSY. (PUSH MODELS)
PAGE 52 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — CONSOLE ASSY. (PUSH MODELS)
CONSOLE ASSY. PUSH
NO PART NO PART NAME QTY. REMARKS
1 28796-351 HANDLE ASSY. 1
2 15081 GRIP, 1”ID, H/W #40001610055 2
3 4196 SCREW, HHC 3/8-16 X .75 4
4 0166 A WASHER, LOCK 3/8 MED. 4
5 10136 WASHER, FLAT SAE 3/8 4
6 28791-751 HOUSING ASSY. - RED 1
7 28805-701 COVER, CONSOLE SIDE - RED 1
8 29013-001 WRENCH, BOX END 1 1/2 1
9 1579 SCREW, HHC 1/4-20 X 1/2 4
10 0181 B WASHER, LOCK 1/4 MED. 8
11 0948 WASHER, FLAT SAE 1/4 4
12 0205 SCREW, HHC 3/8-16 X 1.0 8
13 0166 A WASHER, LOCK 3/8 MED. 8
14 4001 WASHER, FLAT USS 3/8 PLD 8
15 35127 SWITCH, ENGINE ON/OFF ...................................... 1 ......... SAFETY ITEM
16 35200 WIRE, ENGINE ON/OFF SWITCH ........................... 1 ......... SAFETY ITEM
17 19266 BLIND NUT, 1/4-20 4
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 53
MQ SP2 SLAB SAW — CONSOLE ASSY. (SELF-PROPELLED MODELS)
CONSOLE ASSY. (SELF- PROPELLED MODELS)
PAGE 54 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — CONSOLE ASSY. (SELF-PROPELLED MODELS)
CONSOLE ASSY. (SELF- PROPELLED MODELS)
NO PART NO PART NAME QTY. REMARKS
1 28796-351 HANDLE ASSY. 1
2 15081 GRIP, 1” ID 2
3 4196 SCREW, HHC 3/8-16 X .75 4
4 0166 A WASHER, LOCK 3/8 MED. 4
5 10136 WASHER, FLAT SAE 3/8 4
6 28091-401 SHIFT CONTROL ASSY. 1
8 28834-001 COVER, REAR 1
9 0131 A SCREW, HHC 1/4-20 X 3/4 2
10 1002 4 NUT, NYLOC 1/4-20 2
11 4001 WASHER, FLAT USS 3/8 PLD 8
12 1579 SCREW, HHC 1/4-20 X 1/2 8
13 0181 B WASHER, LOCK 1/4 MED. 8
14 28791-751 HOUSING ASSY. - RED 1
15 28805-701 COVER, CONSOLE SIDE, - RED 1
16 29013-001 WRENCH, BOX END 1 1/2 1
17 0948 WASHER, FLAT SAE 1/4 4
18 0205 SCREW, HHC 3/8-16 X 1.0 8
19 0166 A WASHER, LOCK 3/8 MED. 8
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 55
MQ SP2 SLAB SAW — 13HP HONDA ENGINE MOUNT ASSY.
13HP HONDA ENGINE MOUNT ASSY.
PAGE 56 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — 13HP HONDA ENGINE MOUNT ASSY.
13HP HONDA ENGINE MOUNT ASSY.
NO PART NO PART NAME QTY. REMARKS
1 15868-032 SCREW, SQHS 1/2-13 X 4, CUP PLAIN 1
2 0447 WASHER, FLAT SAE 1/2 9
3 968011 NUT, HEX FINISH 1/2-13 1
4 10176 NUT, NYLOC 1/2-13 4
5 3214 SCREW, HHC 1/2-13 X 1 1/4 4
6 9154 SCREW, HHC 3/8-16 X 1 3/4 4
7 10136 WASHER, FLAT SAE 3/8 8
8 10133 NUT, NYLOC 3/8-16 4
9 28804-351 ENGINE BASE ASSY. 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 57
MQ SP2 SLAB SAW — 20HP HONDA ENGINE MOUNT ASSY.
20HP HONDA ENGINE MOUNT ASSY.
PAGE 58 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — 20HP HONDA ENGINE MOUNT ASSY.
20HP HONDA ENGINE MOUNT ASSY.
NO PART NO PART NAME QTY. REMARKS
1 15868-032 SCREW, SQHS 1/2-13 X 4, CUP PLAIN 1
2 0447 WASHER, FLAT SAE 1/2 9
3 968011 NUT, HEX FINISH 1/2-13 1
4 10176 NUT, NYLOC 1/2-13 4
5 3214 SCREW, HHC 1/2-13 X 1 1/4 4
6 4370 SCREW, HHC 3/8-16 X 2 1/4 4
7 10136 WASHER, FLAT SAE 3/8 8
8 10133 NUT, NYLOC 3/8-16 4
9 28804-351 ENGINE BASE ASSY. 1
10 27044-001 SPACER 2
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 59
13HP HONDA ENGINE ASSY.
MQ SP2 SLAB SAW — 13HP HONDA ENGINE ASSY.
PAGE 60 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — 13HP HONDA ENGINE ASSY.
13HP HONDA ENGINE ASSY.
NO PART NO PART NAME QTY. REMARKS
1 15103 ENGINE, HONDA 13HP, GX390K1QWT2 1
2 23665-001 PULLEY, ENGINE 13 HP, 3F3V26X1 ............................ 1 .......... 13HP PUSH MODELS
2 23703-003 PULLEY, ENGINE 13 HP, 4F3V26X1 1 13HP SELF-PROP MODELS
3 6059 B KEY 1/4" SQ. X 2, 1018 STOCK 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 61
20HP HONDA ENGINE ASSY.
MQ SP2 SLAB SAW — 20HP HONDA ENGINE ASSY.
PAGE 62 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — 20HP HONDA ENGINE ASSY.
20HP HONDA ENGINE ASSY.
NO PART NO PART NAME QTY. REMARKS
1 15104 ENGINE, HONDA 20HP GX620TXF2 1
2 28833-002 PULLEY, ENGINE C3 20H20, 4F3V412 1
3 28099-001 MOUNT, IDLER SPRING 1
4 923203 SCREW, SHC 1/4-20 X 3/4 2
5 6059 B KEY 1/4" SQ. X 2, 1018 STOCK 1
6 28088-002 PULLEY, TRANSMISSION 2
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 63
MQ SP2 SLAB SAW — POINTERS AND COVERS ASSY.
POINTERS AND COVERS ASSY.
PAGE 64 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — POINTERS AND COVERS ASSY.
POINTER AND COVERS ASSY.
NO PART NO PART NAME QTY. REMARKS
1 28646-351 BLADE GUIDE WELDMENT 1
2 28649-001 SPANNER BUSHING CSI 1
3 28648-001 WHEEL, 3.00 X 1.25 .50 ID POLY CSI 1
4 28647-001 POINTER 1
5 1456 NUT, HEX FINISH 3/8-16 2
6 10133 NUT, NYLOC 3/8-16 2
7 15114 SLEEVE, SASH 2
8 60087 ROPE, 1/4” NYLON, BRAIDED, WHITE 7
9 0655 SCREW, HHC 5/16-18 X 3/4 7
10 0161 C WASHER, LOCK 5/16 MED. 7
11 0300 B WASHER, FLAT SAE 5/16 7
12 10136 WASHER, FLAT SAE 3/8 3
13 0166 A WASHER, LOCK 3/8 MED. 3
14 0205 SCREW, HHC 3/8-16 X 1.0 3
15 28799-751 BELT GUARD, - RED 1
16 28835-001 GUARD, PULLEY 1
19 29745-754 SPINDLE GUARD ASSY. - RED 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 65
WATER SYSTEM ASSY.
MQ SP2 SLAB SAW — WATER SYSTEM ASSY.
PAGE 66 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — WATER SYSTEM ASSY.
WATER SYSTEM FROM CONSOLE SP
NO PART NO PART NAME QTY. REMARKS
1 12694-008 HOSE CLAMP, SPRING TYPE 7/8 O.D HOSE 4
2 23255-004 HOSE, WATER 1/2 X 37 1
3 23566-001 FITTING, PLASTIC 90 1/2MP X 1/2BARB 1
4 23259-001 VALVE, BALL 1/2 MPT BRASS NIBCO T585-70 1
5 23254-001 FITTING, NIPPLE 1/2MP X 2 GALV. 1
6 16378-009 U-BOLT W/NUTS 1
7 15544 FITTING, BRASS 1/2FP-3/4F GRDN., STR 1
8 24778-001 FITTING, BRASS 1/2 BARB X 3/4 GRDN 1
9 1662 TIE, CABLE TY-RAP BLACK 2
10 28861-501 TRIM KIT, WATER TANK RUBBER 1
11 28089-001 TANK, 5 GAL. WATER ............................................... 1 ......... INCLUDES ITEM W/
12 27040-001 HOSE, 19 IN. VINYL WATER TANK 1
13 28861-001 CORD, TANK RETAINER 1
14 28860-001 KNOB 1
15 06499-004 HHCS 1/4-20 x 1/2 1
16
28089-002 VALVE, WATER TANK (SPIGOT ONLY) 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 67
BLADE GUARD ASSY.
MQ SP2 SLAB SAW — BLADE GUARD ASSY.
PAGE 68 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — BLADE GUARD ASSY.
BLADE GUARD ASSY.
NO PART NO PART NAME QTY. REMARKS
1 29406-754 BLADE GUARD W/A - RED 1
2 28729-002 GUARD, SPLASH BLADE 1
3 60021 HOSE, 3/8ID X 5/8OD BRAIDED PVC “PAC” 1.670
4 0131 A SCREW, HHC 1/4-20 X 3/4 2
5 10024 NUT, NYLOC 1/4-20 2
6 24642-001 Y-CONNECTOR 3/8 1
7 12694-006 HOSE CLAMP, SPRING TYPE 3/4 O.D. HOSE 2
8 24778-001 FITTING, BRASS 1/2BARB X 3/4F GRDN 1
9 18626-001 SPRING TENSION, GUARD BLADE 2
10 22129-001 PIPE STRAP 3/8 2
11 21168 SCREW, HHC 3/8-16 X 4.75 1
12 0424 SCREW, HHC 1/4-20 X 1 1/4 4
13 0949 NUT, HEX FINISH 1/4-20 PLATED 4
14 0181 B WASHER, LOCK 1/4 MED. 4
15 0948 WASHER, FLAT SAE 1/4 6
16 0205 SCREW, HHC 3/8-16 X 1.0 1
17 0166 A WASHER, LOCK 3/8 MED. 2
18 10136 WASHER, FLAT SAE 3/8 2
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 69
MQ SP2 SLAB SAW — MANUAL RAISE AND LOWER ASSY. (20 IN. )
MANUAL RAISE AND LOWER ASSY. (20 IN.)
PAGE 70 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — MANUAL RAISE AND LOWER ASSY. (20 IN. )
JACK SCREW ASSY. 20” BLADE
NO PART NO PART NAME QTY. REMARKS
1 28793-352 JACKPOST ASSY. 1
2 2621 ZERK, GREASE STR. 1/4-28 1
3 28806-001 JACKSCREW 1
4 28083-001 BEARING, FLANGE 1
5 28809-001 SPACER, JACKSCREW 1
6 4568 PIN, ROLL 3/16 X 1 1
7 28877-751 SCREW COVER ASSY., RED 1
8 1579 SCREW, HHC 1/4-20 X 1/2 3
9 0948 WASHER, FLAT SAE 1/4 7
10 0181 B WASHER, LOCK 1/4 MED. 3
11 0730 SCREW, HHC 1/4-20 X 1 2
12 1162 A CAP,GREASE ZERK, #2 1
13 10024 NUT, NYLOC 1/4-20 2
14 1121 SCREW, HHC 3/8-16 X 2 3/4 1
15 1876 NUT, HEX JAM 3/8-16 CLASS 2B 1
16 4403 KNOB, SHIFT 1
17 28808-002 ARM-CRANK 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 71
BATTERY ASSY.
MQ SP2 SLAB SAW — BATTERY ASSY.
PAGE 72 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — BATTERY ASSY.
BATTERY ASSY.
NO PART NO PART NAME QTY. REMARKS
1 4671 BATTERY, WET GR.U1, GT-X GOLD LA 1
2 28096-001 BRACKET BATTERY 1
3 28095-401 BATTERY HOLD DOWN KIT 425-405 1
4 28093-001 CABLE, BATTERY POS 6GA X 42” RING TONGUE 1
5 28094-001 STRAP, GROUND 1
6 0131 A SCREW, HHC 1/4-20 X 3/4 2
7 0948 WASHER, FLAT SAE 1/4 2
8 0949 NUT, HEX FINISH 1/4-20 PLATED 2
9 0655 SCREW, HHC 5/16-18 X 3/4 3
10 0161 D NUT, HEX FINISH 5/16-18 3
11 0161 C WASHER, LOCK 5/16 MED. 3
12 0300 B WASHER, FLAT SAE 5/16 6
13 0181 B WASHER, LOCK 1/4 MED. 2
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 73
MQ SP2 SLAB SAW — TRANSMISSION ENGAGE LEVER ASSY.
TRANSMISSION ENGAGE LEVER ASSY.
PAGE 74 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — TRANSMISSION ENGAGE LEVER ASSY.
HYD. TRANSMISSION ENGAGE LEVER ASSY.
NO PART NO PART NAME QTY. REMARKS
1 28825-351 LEVER ASSY. TRANS. ENGAGE 1
2 3360 GRIP, 1/4 X 1 BLACK 1
3 28822-351 MOUNT ASSY., LEVER RED 1
4 0655 SCREW, HHC 5/16-18 X 3/4 4
5 10136 WASHER, FLAT SAE 3/8 6
6 6014 B PIN, COTTER 3/32D X 1.0 1
7 08326-005 PIN, CLEVIS 5/16 X 1 O’ALL LENGHT PLATED 2
8 07028-031 PIN, COTTER 3/32D X 1/2 2
9 5283 NUT, NYLOC 5/16-18 8
10 08326-019 PIN, CLEVIS 3/8 X 2” USEABLE LENGHT 1
11 2199 NUT, HEX JAM 3/8-24 2
12 08327-012 YOKE END, 3/8-24 X 2.50 2
13 28830-001 ROD, TRANS. ENGINE 1
14 28819-351 TRANS. BRACKET ASSY. 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 75
MQ SP2 SLAB SAW — HYDROSTATIC TRANSMISSION ASSY.
HYDROSTATIC TRANSMISSION
PAGE 76 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SLAB SAW — HYDROSTATIC TRANSMISSION ASSY.
HYDROSTATIC TRANSMISSION ASSY.
NO PART NO PART NAME QTY. REMARKS
1 20559-001 SPRING, EXT. 3.38FL X 71OD X .105 1
2 1493 SCREW, HHC 3/8-18 X 3.25 4
3 28836-001 LINK, RETURN SPRING 1
4 10133 NUT, NYLOC 3/8-16 7
5 10136 WASHER, FLAT SAE 3/8 8
6 1023 SCREW, HHC 3/8-16 X 1 1/4 GR 5 2
7 15354 TRANSMISSION, HYD EATON 1
8 1578 KEY, WOODRUFF #3 2
9 0166 A WASHER, LOCK 3/8 MED. 4
10 1456 NUT, HEX FINISH 3/8-16 4
11 28828-351 SHIFT ARM ASSY. 1
12 28829-001 PIN, PIVOT 2
13 10450 SCREW, SHS 10-32 X 1/4 1
14 103530-000 CAP, TRANSMISSION 1
h
h
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 77
HYDROSTATIC DRIVE ASSY.
MQ SP2 SAW — HYDROSTATIC DRIVE ASSY.
PAGE 78 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
MQ SP2 SAW — HYDROSTATIC DRIVE ASSY.
HYDROSTATIC DRIVE ASSY.
NO PART NO PART NAME QTY. REMARKS
1 23227-001 SPROCKET, TRANSMISSION 12 TOOTH MACH 1
2 25039 SCREW, SHS 10-24 X 1/4 2
3 23231-503 CHAIN, ROLLER .375 PITCH X 21.75 1
4 10504-035 LINK, CHAIN 1
5 5283 NUT, NYLOC 5/16-18 8
6 28084-001 SPROCKET, 3548 X 3/4 1
7 0126 KEY, WOODRUFF #9 3
8 28832-001 JACKSHAFT 1
9 23284-001 BEARING, FLANGE .34SQ x 3/4ID 2
10 0300 B WASHER, FLAT SAE 5/16 4
11 2623 SCREW, HHC 5/16-18 X 1-1/4 4
12 28831-001 GEAR, DRIVE 2
13 1578 KEY, WOODRUFF #3 1
14 28087-001 PULLEY, MA60 X 17MM 1
15 25682-001 IDLER PULLEY 1
16 9154 SCREW, HHC 3/8-16 X 1 3/4 1
17 10136 WASHER, FLAT SAE 3/8 1
18 10133 NUT, NYLOC 3/8-16 4
19 23303-001 IDLER ARM 1
20 23230-001 SPRING EXT. IDLE 1
21 1284 SCREW, HHC 3/8-16 X 1 1/2 1
22 18574-004 WASHER, BELLEVILLE 3/8 1
23 28864-001 WASHER, FIBRE 1
25 07055-050 V-BELT, TRANSMISISON 4L500 .............................. 1 .......... 13HP SELF-PROP. MODELS
25 07055-051 V-BELT, TRANSMISSION 4L510 .............................. 1 .......... 20HP SELF-PROP. MODELS
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 79
AIR CLEANER ASSY.
HONDA GX390K1QWT2 ENGINE — AIR CLEANER ASSY.
PAGE 80 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 16271ZE2000 GASKET, ELBOW 1
2 17210ZE3505 ELEMENT, AIR CLEANER ........................ 1 ......... INCLUDES ITEMS W/
3
4# 17219HA2405 SEAL, AIR CLEANER COVER 1
5 17230ZE3841 COVER, AIR CLEANER (CYCLONE) 1
6
7# 17238ZE2310 COLLAR, AIR CLEANER 2
8# 17239ZE3840 COLLAR B, AIR CLEANER 1
9 17410ZE3840 ELBOW, AIR CLEANER ............................. 1......... INCLUDES ITEMS W/#
10 17470ZE3841 CASE, PRE AIR CLEANER 1
11 17475ZE3841 CAP, PRE AIR CLEANER 1
12 17476ZE3841 GUIDE, PRE AIR CLEANER 1
13 90142MB0000 SCREW, PAN 5X16.5 5
14 90325044000 WINGNUT, TOOL BOX SETTING 2
15 90009ZE2003 BOLT- WASHER 6X22 1
16 0405006000 NUT, FLANGE 6MM 2
17218ZE3505 FILTER, OUTER 1
*
17232891000 GROMMET, AIR CLEANER 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 81
CAMSHAFT ASSY.
HONDA GX390K1QWT2 ENGINE — CAMSHAFT ASSY.
PAGE 82 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 14100ZF6W01 CAMSHAFT ASSEMBLY .......................... 1 ......... INCLUDES ITEM W/
2 14410ZE3013 ROD, PUSH 2
3 14431ZE2010 ARM, VALVE ROCKER 2
4 14441ZE2000 LIFTER, VALVE 2
5 14451ZE1013 PIVOT, ROCKER ARM 2
6
7 14711ZE3000 VALVE, INTAKE 1
8 14721ZE3000 VALVE, EXHAUST 1
9 14751ZE2003 SPRING, VALVE 2
10 14771ZE2000 RETAINER, INTAKE VALVE SPRING 1
11 14773ZE2000 RETAINER, EXHAUST VALVE SPRING 1
12 14775ZE2010 SEAT, VALVE SPRING 1
13 14781ZE2000 ROTATOR, VALVE 1
14 14791ZE2010 PLATE, PUSH ROD GUIDE 1
15 90012ZE0010 BOLT, PIVOT 8MM 2
16 90206ZE1000 NUT, PIVOT ADJ. 2
17 12209ZE8003 SEAL, VALVE STEM 1
14568ZE1000 SPRING, WEIGHT RETURN 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 83
CARBURETOR ASSY.
HONDA GX390K1QWT2 ENGINE — CARBURETOR ASSY.
PAGE 84 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1
#+ 16010ZE2812 GASKET SET 1
*
2
*
3
*
4
*
5
*
6
+ 16024ZE1811 SCREW SET, DRAIN ...........................1 ............. INCLUDES ITEM W/#
*
7
*
8
*
9 16100ZF6V21 CARBURETOR ASSY. (BE85C B) ....... 1 ............. INCLUDES ITEMS W/
10
*
11
*
12
*
13 16211ZF6000 INSULATOR, CARBURETOR 1
14 16220ZA0702 SPACER, CARBURETOR 1
15 16221ZF6800 GASKET, CARBURETOR 1
16 16223ZE3W00 GASKET, INSULATOR 1
20 16610ZE1000 LEVER, CHOKE (STD) ........................ 1 ............. INCLUDES ITEM W/$
22
*
23
*
24
*
25
*
26
*
28
*
31$ 9430520122 PIN, SPRING (2X12) 1
33
*
33 99101ZH80980 JET, MAIN (#98) (OPTIONAL) 1
33
*
34
*
35
*
16011ZA0931 VALVE SET, FLOAT 1
16013ZA0931 FLOAT SET 1
16015ZE8005 CHAMBER SET, FLOAT ...................... 1 ............. INCLUDES ITEMS W/+
16016ZH7W01 SCREW SET 1
16028ZE0005 SCREW SET B .................................... 1 ............. INCLUDES ITEM W/#
16044ZE3W20 CHOKE SET 1
16124ZE0005 SCREW, THROTTLE STOP 1
16166ZF6W10 NOZZLE, MAIN 1
16173001004 GASKET, FUEL STRAINER CUP 1
16953ZE1812 LEVER, VALVE 1
16954ZE1812 PLATE, LEVER SETTING 1
16956ZE1811 SPRING, VALVE LEVER 1
16957ZE1812 GASKET, VALVE 1
16967ZE0811 CUP, FUEL STRAINER 1
93500030060H SCREW, PAN (3X6) 2
99101ZH80950 JET, MAIN (#95) (OPTIONAL) 1
99101ZH81000 JET, MAIN (#100) 1
99204ZA00450 JET SET, PILOT (#45) .........................1 ............. INCLUDES ITEM W/#
16172ZE3W10 COLLAR, SET 1
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 85
CONTROL ASSY.
HONDA GX390K1QWT2 ENGINE — CONTROL ASSY.
PAGE 86 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO. PART NO. PART NAME QTY. REMARKS
2 16551ZE3000 ARM, GOVERNOR 1
3 16555ZE3000 ROD, GOVERNOR 1
4 16561ZE3000 SPRING, GOVERNOR 1
5 16562ZE3000 SPRING, THROTTLE RETURN 1
6 16570ZE3W20 CONTROL ASSY. (REMOTE) .................... 1 ......... INCLUDES ITEMS W/
10
11
12
13
14
15
17
18
21 90013883000 BOLT, FLANGE (6X12) (CT200) 2
22 90015ZE5010 BOLT, GOVERNOR ARM 1
24
27
28
29 9405006000 NUT, FLANGE (6MM) 1
16571ZE3W00 LEVER, CONTROL 1
*
16574ZE1000 SPRING, LEVER 1
*
16575ZE2W00 WASHER, CONTROL LEVER 1
*
16576891000 HOLDER, CABLE 1
*
16578ZE1000 SPACER, CONTROL LEVER 1
*
16581ZE3W00 BASE, CONTROL 1
*
16584883300 SPRING, CONTROL ADJUSTING 1
*
16592883310 SPRING, CABLE RETURN 1
*
90114SA0000 NUT, SELF-LOCK (6MM) 1
*
93500050320A SCREW, PAN (5X32) 1
*
93500050160A SCREW, PAN (5X16) 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 87
CRANKCASE COVER ASSY.
HONDA GX390K1QWT2 ENGINE — CRANKCASE ASSY.
PAGE 88 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CRANKCASE ASSY.
CRANKCASE COVER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
2 11300ZE3602 COVER ASSY., CRANKCASE (Q-TYPE) .........1 ................ INCLUDES ITEMS W/
3 11381ZE3801 GASKET, CASE COVER 1
4 15600ZG4003 CAP ASSY., OIL FILLER ................................. 1 ................ INCLUDES ITEM W/#
5 15600735003 CAP ASSY., OIL FILLER .................................1 ................ INCLUDES ITEM W/#
8# 15625ZE1003 GASKET, OIL FILLER CAP 2
9 16510ZE3000 GOVERNOR ASSY. ..........................................1 ................ INCLUDES ITEMS W/+
10
+ 16511ZE8000 WEIGHT, GOVERNOR 3
*
11
+ 16512ZE3000 HOLDER, GOVERNOR WEIGHT 1
*
12
+ 16513ZE2000 PIN, GOVERNOR WEIGHT 3
*
13
*
13
*
15
*
16 90701HC4000 PIN, DOWEL (8X12) 2
17
*
18
*
19 957010804000 BOLT, FLANGE (8X40) 7
20
*
21
*
16531ZE2000 SLIDER, GOVERNOR 1
16531Z0A000 SLIDER, GOVERNOR 1
90602ZE1000 CLIP, GOVERNOR HOLDER 1
91201ZE3004 OIL SEAL (35X52X8) 1
9410106800 WASHER, PLAIN (6MM) 1
961006202000 BEARING, RADIAL BALL (6202) 1
961006207000 BEARING, RADIAL BALL (6207) 1
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 89
CRANKSHAFT ASSY.
HONDA GX390K1QWT2 ENGINE — CRANKSHAFT ASSY.
PAGE 90 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO. PART NO. PART NAME QTY. REMARKS
2 13310ZF6W10 CRANKSHAFT (Q-TYPE).......................... 1 ......... INCLUDES ITEM W/
8 13351ZE3010 WEIGHT, BALANCER 1
11 90745ZE2600 KEY(6.3X6.3X43) 1
12
91001ZF6003 BEARING, RADIAL BALL (6207S) 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 91
HONDA GX390K1QWT2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 92 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 12000ZF6W13 CYLINDER ASSY. (ALERT) ....................... 1 ......... INCLUDES ITEMS W/
2 15510ZE2043 SWITCH ASSY., OIL LEVEL 1
4 16541ZE3010 SHAFT, GOVERNOR ARM 1
9 90131896650 BOLT, DRAIN PLUG 2
10 90446KE1000 WASHER (8.2X17X0.8) 1
12
13
14 91353671003 O-RING (13.5X1.5) (ARAI) 1
17 9405010000 NUT, FLANGE (10MM) 1
18 9410912000 WASHER, DRAIN PLUG (12MM) 2
19 9425110000 PIN, LOCK (10MM) 1
20 957010601200 BOLT, FLANGE (6X12) 2
21
22 34150ZH7003 ALERT UNIT, OIL 1
23 90013883000 BOLT, FLANGE (6X12) (CT200) 1
91201ZE3004 OIL SEAL (35X52X8) 1
*
91201ZE9003 OIL SEAL (8X14X5) 1
*
961006202000 BEARING, RADIAL BALL (6202) 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 93
CYLINDER HEAD ASSY.
HONDA GX390K1QWT2 ENGINE — CYLINDER HEAD ASSY.
PAGE 94 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 12200ZF6W01 CYLINDER HEAD ............................................. 1 ................ INCLUDES ITEMS W/
2
3
4
5 12251ZF6W00 GASKET, CYLINDER HEAD 1
6 12310ZE3791 COVER, HEAD 1
7 12315ZE3840 TUBE, BREATHER 1
8 12391ZE2020 GASKET, CYLINDER HEAD COVER 1
10 17316611000 CLIP, BREATHER TUBE 2
11 90014ZE2000 BOLT, HEAD COVER 1
12 90042ZE8000 BOLT, STUD (8X131.5) 2
13 92900080320E BOLT 2, STUD (8X32) 2
14 90441ZE2010 WASHER, HEAD COVER 1
16 9430112200 PIN A, DOWEL (12X20) 2
17 957011008000 BOLT, FLANGE (10X80) 4
18 9807955846 SPARK PLUG (BPR5ES) (NGK) (OPT.) 1
18 9807956846 SPARK PLUG (BPR6ES) (NGK) 1
12204ZE2306 GUIDE, VALVE (OS) (OPTIONAL) 1
*
12205ZE2305 GUIDE, EX. VALVE (OS) (OPTIONAL) 1
*
12216ZE2300 CLIP, VALVE GUIDE 1
*
*
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 95
FAN COVER ASSY.
HONDA GX390K1QWT2 ENGINE — FAN COVER ASSY.
PAGE 96 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
4 16731ZE2003 CLIP, TUBE 1
7 19610ZE3010ZB COVER, FAN *NH1* (BLACK) 1
10 19631ZE3W00 SHROUD 1
13 36100ZH7003 SWITCH ASSY., ENGINE STOP 1
15 90013883000 BOLT, FLANGE (6X12) (CT200) 6
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 97
FLYWHEEL ASSY.
HONDA GX390K1QWT2 ENGINE — FLYWHEEL ASSY.
PAGE 98 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
HONDA GX390K1QWT2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 19511ZE3000 FAN, COOLING 1
3 28450ZE3W11 PULLEY, STARTER (SCREEN GRID) 1
7 31100ZE3701 FLYWHEEL 1
10 90201ZE3V00 NUT, SPECIAL (16MM) (1) 1
11 90741ZE2000 KEY, SPECIAL WOODRUFF (25X18) 1
MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06) — PAGE 99
FUEL TANK ASSY.
HONDA GX390K1QWT2 ENGINE — FUEL TANK ASSY.
PAGE 100 — MQ SP2 SLAB SAW — PARTS & OPERATION MANUAL — REV. #7 (09/08/06)
Loading...