MULTIQUIP SideWinder HS62A Parts Manual

Download

OPERATION & PARTS MANUAL

SideWinder

MODEL HS62A

CUT-OFF SAW

Revision #0 (03/20/06)

To find the latest revision of this

publication, visit our website at:

www.multiquip.com

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are:

Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.

Your risk from these exposures varies, dependingonhowoftenyoudothistype of work. To reduce your exposure to

these chemicals: work in aALWAYS

well ventilated area, and work with

approved safety equipment, such as

dust masks that are specially designed to filter out microscopic particles.

NOTE PAGE

HS62A CUT-OFF SAW — TABLE OF CONTENTS

MULTIQUIP — HS62A CUT-OFF SAW

Proposition 65 Warning ............................................. 2

Table Of Contents ..................................................... 4

Parts Ordering Procedures ....................................... 5

Safety Message Alert Symbols .............................. 6-7

Rules For Safe Operation .................................... 8-11

Specifications (Saw/Engine) ................................... 12

Decal Placement ..................................................... 13

Controls & Components ..................................... 14-15

Blade Installation Instructions ................................. 16

Water Kit Installation Instructions ............................ 17

Blades ..................................................................... 18

Initial Start-Up/Operation ................................... 19-20

Maintenance ...................................................... 21-25

Troubleshooting (Blade) .......................................... 26

Troubleshooting (Engine) ................................... 27-28

Filter Kits ................................................................. 29

Explanation of Codes in Remarks Column ............. 30

Suggested Spare Parts ........................................... 31

Carburetor Mounting Assembly ......................... 56-57

Carburetor Assembly ......................................... 58-59

Crankshaft and Piston Assembly .......................60-61

Water Kit Assembly ............................................ 62-63

Tools ................................................................... 64-65

Recommended Diamond Blades ............................ 66

Terms and Conditions of Sale — Parts ................... 67

COMPONENT DRAWINGS

Muffler Assembly ............................................... 32-33

Recoil Start Assembly ........................................ 34-35

Crankcase Assembly ......................................... 36-37

V-belt Cover (Clutch Side) Assembly ................. 38-39

V-Belt Cover (Pulley) Blade Guard Assembly .... 40-41

Fuel Tank Assembly ........................................... 42-43

Lifting Handle and Roller Assembly ................... 44-45

Throttle Linkage Assembly ................................ 46-47

Flywheel Cover Assembly .................................. 48-49

Flywheel Assembly ............................................ 50-51

Ignition Assembly ............................................... 52-53

Air Filter Assembly ............................................. 54-55

NOTE

Specifications and part numbers are subject to change without notice.

PAGE 4 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

Effective: June 1st, 2005

Ordering parts has never been easier!

PARTS ORDERING PROCEDURES

Choose from three easy options:

Best Deal!

Order via Internet (Dealers Only):

Order parts on-line using Multiquip’s SmartEquip website!

■

View Parts Diagrams

■

Order Parts

■

Print Specification Information

Goto www.multiquip.com and click on

Order Parts

to log in and save!

Order via Fax (Dealers Only):

All customers are welcome to order parts via Fax.

Domestic (US) Customers dial:

1-800-6-PARTS-7 (800-672-7877)

Order via Phone:

Non-Dealer Customers:

Contact your local Multiquip Dealer for parts or call 800-427-1244 for help in locating a dealer near you.

If you have an MQ Account, to obtain a Username and Password, E-mail us at:

parts@multiquip.com.

To obtain an MQ Account, contact your District Sales Manager for more information.

Use the

internet

Standard orders

on complete part numbers.*

Fax

your order in and qualify for a 3% Discount

Standard orders

complete part numbers.*

Domestic (US) Dealers Call:

1-800-427-1244

and qualify for a 5% Discount

for all orders which include

International Customers

their local Multiquip Representatives for Parts Ordering information.

Note: Discounts Are Subject To Change

should contact

❒❒

❒

❒❒

❒

❒❒

❒

❒❒

❒

❒❒ ❒❒

❒

❒❒

❒

❒❒

www.multiquip.com

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 5

When ordering parts, please supply:

❒❒

Dealer Account Number

Dealer Name and Address

Shipping Address (if different than billing address)

Return Fax Number Applicable Model Number

Quantity, Part Number and Description of Each Part

NOTE

Unless otherwise indicated by customer, all orders are treated as within 24 hours. We will make every effort to ship if received prior to 2PM PST.

WE ACCEPT ALL MAJOR CREDIT CARDS!

❒

❒❒

Stock Orders

Specify Preferred Method of Shipment:

✓

Fed Ex/UPS

Priority One

■

Ground

■ Next Day Second/Third Day

■

Air Shipments

must be noted on fax or web order form.

✓ DHL ✓

Tr u ck

Standard Orders

the same day the order is received,

and will ship

HS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS

FOR YOUR SAFETY AND THE SAFETY OF OTHERS! HAZARD SYMBOLS

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Owner's Manual has been

NOTE

to the maintenance section of this manual for data relative to its safe operation.

Before using this SAW, ensure that the operating individual has read and understands all instructions in this manual.

developed to provide complete instructions for the safe and efficient operation of the MULTIQUIP MODEL HS62A maintenance information, please refer

CUT-OFF SAW

. For engine

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words:

DANGER, WARNING, or CAUTION.

Lethal Exhaust Gases

Engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and

odorless, and can cause death if inhaled. NEVER operate this equipment in a confined

area or enclosed structure that does not provide ample free flow air.

Explosive Fuel

Gasoline is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids. DO NOT fill the fuel tank while the engine is running or hot. DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system. Store fuel in

approved containers, in well-ventilated areas and away from sparks and flames. NEVER use fuel as a cleaning agent.

DANGER

You WILL be

KILLED

NOT follow directions.

WARNING

You CAN be

KILLED

NOT follow directions.

CAUTION

You CAN be

INJURED

SERIOUSLY

injured if you DO

if you DO NOT follow directions.

Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.

Rotating Parts

NEVER operate equipment with covers, or

guards removed. Keep and

clothing

prevent injury.

fingers, hands, hair

away from all moving parts to

PAGE 6 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS

Accidental Starting

ALWAYS place the engine ON/OFF

switch in the OFF position, when the saw is not in use.

Over Speed Conditions

NEVER tamper with the factory settings of the

engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable.

Guards and Covers In Place

NEVER operate the saw without blade guards

and covers in place. Adhere to safety guidelines ANSI, OSHA, or other applicable local regulations.

Respiratory Hazard

ALWAYS wear approved respiratory protection.

Sight and Hearing hazard

ALWAYS wear approved eye and hearing

protection.

Equipment Damage Messages

Other important messages are provided throughout this manual to help prevent damage to your concrete saw, other property, or the surrounding environment.

Rotating Blade

NOTE

Rotating blade can cut and crush. Keep hands and feet clear.

This

concrete/asphalt saw

, other property, or the surrounding environment could be damaged if you do not follow instructions.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 7

HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION

■

WARNING - Read This Manual

Failure to follow instructions in this manual may lead to

Serious Injury

or even

Death

. This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only.

The following safety guidelines should always be used when operating the Multiquip HS62A Cut-off Saw.

SAFETY

■

DO NOT operate or service this equipment before reading this entire manual.

■

This equipment should not be operated by persons under 18 years of age.

■

NEVER operate the saw without proper protective clothing, shatterproof glasses, steel-toed boots and other protective devices required by the job.

NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool before servicing the saw.

■

High Temperatures – Allow the engine to cool before adding fuel or performing service and maintenance functions. Contact with

■

The engine of this saw requires an adequate free flow of cooling air. NEVER operate the saw in any enclosed or narrow area where free flow of the air is restricted. If the air flow is

hot!

components can cause serious burns.

restricted it will cause serious damage to the saw's engine and may cause injury to people. Remember the saw's engine gives off

DEADLY

gas.

carbon monoxide

■

NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.

■

NEVER operate the saw under the influence or drugs or alcohol.

■

NEVER use accessories or attachments, which are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

■

Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.

■

Whenever necessary, replace nameplate, operation and safety decals when they become difficult read.

■

ALWAYS check the saw for loosened hardware such as nuts and bolts before starting.

■

ALWAYS refuel in a well-ventilated area, away from sparks and open flames.

ALWAYS use extreme caution when working with flammable liquids. When refueling, STOP the engine and allow it to cool.

NEVER

Fire or explosion could result from

vapors

engine.

NEVER operate the saw in an explosive atmosphere where fumes are present or near combustible materials. An explosion or fire could result causing severe

smoke

around or near the saw.

fuel

, or if fuel is spilled on a

hot!

bodily harm

or even death.

ALWAYS move the saw at least 10 feet away from the fueling

point before starting the engine and make sure the gas cap on the saw and the fuel can are properly tightened.

PAGE 8 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

■

Topping-off to filler port is dangerous, as it tends to spill fuel.

■

NEVER use fuel as a cleaning agent.

HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION

General Safety

■

ALWAYS read, understand, and follow procedures in Operator's Manual before attempting to operate this equipment.

■

ALWAYS wear proper respiratory (mask), hearing and eye protection equipment when operating the saw.

■

ALWAYS be sure the operator is familiar with proper safety precautions and operating techniques before using the saw.

■

ALWAYS inspect the blade, flanges and shafts for damage before installing the blade.

■

ALWAYS use high-speed, reinforced, abrasive blades - 1/8" (3.17 mm) thick (minimum) or high-speed, diamond blades specifically rated with a maximum operating speed of at least 5,400 RPM on 14" (350 mm) or 6,200 RPM on 12" (300 mm).

■

ALWAYS use high-speed reinforced, abrasive blades or high-speed, diamond blades marked with a 1" (25.4 mm) hole for a 1" (25.4 mm) flange, or a 20 mm hole for a 20 mm flange.

■

ALWAYS use abrasive blades or high-speed diamond blades marked for use with gasoline-powered, hand-held, portable, abrasive cutting-off saws.

■

ALWAYS read all safety materials and instructions that accompany any blade used with this saw.

■

ALWAYS inspect each blade carefully before using it. If there are any signs of damage or unusual wear, DO NOT USE

THE BLADE.

■

ALWAYS verify the blade arbor hole matches the saw's spindle before mounting the blade.

■

ALWAYS hold the saw with both hands when the engine is running. Use a firm grip with thumbs and fingers encircling the handles.

ALWAYS keep all parts of the body away from the cutting-off blades when the engine is running.

ALWAYS keep the handles dry, clean and free of oil or fuel. ALWAYS carry the saw with the engine stopped and the

muffler away from the body. ALWAYS instruct bystanders on where to stand while the

saw is in operation.

ALWAYS clear the work area of unnecessary people. NEVER allow anyone to stand in front of or behind the blade

while the engine is running. ALWAYS make sure the blade is not contacting any objects

before starting the engine. ALWAYS check for buried electrical cables before sawing. If

unsure, contact the local utilities. ALWAYS have all service and maintenance performed by

competent trained service personnel.

ALWAYS clean the saw after each day’s use. ALWAYS have a copy of this manual at the job site. ALWAYS

oil. ALWAYS service air cleaner frequently to prevent carburetor

malfunction. ALWAYS keep clear of

saw is in operation.

ALWAYS maintain this saw in a

all times

ALWAYS keep any inexperienced and unauthorized people

away from the saw at all times. ALWAYS store saw properly when it is not being used.

Equipment should be stored in a clean, dry location out of the reach of children.

stop

the engine before servicing, adding fuel and

rotating

moving parts

safe

operating condition at

while the

■

ALWAYS mount the blade the arbor nut.

■

ALWAYS make sure the blade and flanges are clean and free of dirt and debris before mounting the blade on the saw.

■

ALWAYS use the correct blade for the type of work being done. Check with blade manufacturer if you do not know if blade is correct for desired application.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 9

solidly

and

firmly

. Wrench tighten

NOTE

This saw is designed for certain applications only. DO NOT use or modify this saw for any application other than for which it was designed.

HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION

■

NEVER leave the machine

■

NEVER run the engine without the air filter. Severe engine damage could occur.

■

NEVER wear jewelry or loose fitting clothing that may snag on the controls or moving parts, this can cause a serious injury.

■

NEVER operate this saw without the blade guard, or other protective guards in place.

■

NEVER stand behind or in front of the blade path while the engine is running.

■

NEVER use abrasive blades that are less the 1/8" (3.17 mm) thick.

■

NEVER exceed maximum blade speed shown for each blade size. Excessive speed could result in blade breakage.

■

NEVER use a damaged saw or blades.

■

NEVER try to stop a moving blade with your hand.

■

NEVER use an abrasive blade that has been dropped.

■

NEVER use carbide-tipped or toothed type blades of any kind.

■

NEVER use segmented diamond blades unless they are specifically designed for high-speed, hand-held saws.

■

NEVER place 1 inch (25.4 mm) arbor hole blades on 20 mm flanges.

■

NEVER use the side of a cutting-off blade as a grinder.

■

NEVER cock, jam or wedge the blade in the cut.

■

NEVER operate the saw if the blade does not stop rotating when the throttle trigger is released.

■

NEVER start cutting until you have a clear work area and secure footing.

■

NEVER allow other persons to be near the saw when starting, refueling, or when the saw is operating.

■

NEVER allow bystanders or animals in the work area while using a cutting-off machine.

■

NEVER touch a dry cutting diamond blade immediately after use. These blades require several minutes to cool after each cut.

■

NEVER use damaged or worn blade flanges. Discard any damage or worn saw parts.

unattended

while running.

Diamond Blade Safety

■

Saw Transportation Safety

■

Use appropriate steel centered diamond blades manufactured for use on concrete saws.

WARNING

ALWAYS inspect diamond blades before each use. The

blade should exhibit no cracks, dings, or flaws in the steel centered core and/or rim. Center (arbor) hole must be undamaged and true.

Examine blade flanges for damage, excessive wear and cleanliness before mounting blade. Blade should fit snugly on the shaft and against the inside/outside blade flanges.

Ensure the blade is marked with an operating speed greater than the blade shaft speed of the saw.

Only cut the material that is specified by the diamond blade. Read the specifications of the diamond blade to ensure the proper tool has been matched to the material being cut.

ALWAYS keep blade guards in place. Exposure of the diamond blade must not exceed 180 degrees.

Ensure that the diamond blade does not come into contact with the ground or surface during transportation. DO NOT drop the diamond blade on ground or surface.

The engine governor is designed to permit maximum engine speed in a no-load condition. Speeds that exceed this limit may cause the diamond blade to exceed the maximum safe allowable speed.

Ensure that the blade is mounted correctly for proper operation.

NEVER transport the saw with the blade mounted. ALWAYS use caution when

saw.

ALWAYS tie-down the saw when transporting. ALWAYS use caution and follow the instructions when

loading and unloading the saw.

lifting

and

transporting

this

■

NEVER allow blade exposure from the guard to be more than 180 degrees.

■

NEVER operate this saw without both hands on the handles.

PAGE 10 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — RULES FOR SAFE OPERATION

EMERGENCIES

■

ALWAYS know the location of

the nearest

■

ALWAYS know the location of the

nearest

■

In emergencies nearest phone or Also know the phone numbers of the nearest

ambulance, doctor,

information will be invaluable in the case of an emergency.

fire extinguisher

first aid kit

always

keep a phone on the job site

and

know the location of the

fire department

. This

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 11

HS62A CUT-OFF SAW — SPECIFICATIONS

snoitacificepSwaSffo-tuCA26SH.1elbaT

HxWxL)gnippihS(noisnemiD

thgieW )gk4.01(.sbl9.22

eziSedalB )mm653(.ni41

CmumixaM )mm721(.ni5

htpeDtu

eziSrobrA )mm02(.ni1

mrAgnittuCelbisreveR

epyTenignEdeloocriA,rednilyCelgniS,ekortS-owT

tnemecalpsiD).cc3.36(ni.uc68.3

deepSeldnipSmumixaM001,5MPR

pSenignE000,01MPR

dee

deepSeldI005,2MPR

.ni81x33x05

)mm754x838x0721(

snoitacificepSecruoSrewoPA26SH.2elbaT

)HxWxL(snoisnemiD

yticapaCknaTleuF)sret

oitaRxiMliO/leuF91egaP,31erugiFeeS

dohteMgnitratStratSlioceR

epyT

noitingI

paG)mm53.(.ni410.

rerutcafunaMKGN/noipmahC

sgulPkrapS

roterubraC

epyTA6RPB/Y7JCR

paG)mm5.0(020.

cafunaMorblaW

rerut

ledoM702DH

epyT

.ni57.51x72.8x31.92

)mm004x012x047(

iL56.(.snollaG71.

cinortcelE

rtnoCdeepS

dello

dexiF-imeS/mgarhpaiD

teJ

PAGE 12 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — DECAL PLACEMENT

P/N DCL 230

Machine Operation And Safety Decals

The HS62A CUT-OFF SAW is equipped with a number of operation and safety decals (Figure 1). Should any of these decals become unreadable, replacements can be obtained from your dealer.

P/N DCL 231

P/N DCL 233A

P/N DCL 232

Figure 1. Safety Decals

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 13

P/N DCL 161

HS62A CUT-OFF SAW — CONTROLS & COMPONENTS

Figure 2. HS62A Cut-off Saw Components 1

Figures 2 and 3 shows the location of the basic controls or components for the Multiquip Model HS62A Cut-off Saw. Listed below is a brief explanation of each control or component.

1. Air Filter – Prevents dirt and debris from entering the engine air intake. Check filter periodically and keep cleaned or replace when necessary. NEVER run engine with a dirty air filter.

2. Muffler – Used to reduce noise and emissions. NEVER! touch muffler when engine is running. Allow engine to cool down. This component gets extremely hot!

3. Guard Adjustmet Knob – Allows for the adjustment of the blade guard. Turn this knob clockwise to tighten, counter-clockwise to loosen.

4. Pulley Lock Pin Hole – Insert a phillips head screw driver or similar tool into this hole to prevent the pulley from rotating.

5. V-belt Tensioning Cam – Allows for the adjustment of the V-belt. To tighten V-belt turn clockwise, to slacken turn counterclockwise.

7. Roller Wheel – Allows for easy free movement of the saw when cutting on a flat surface.

8. V-belt Cover (Clutch) – Unscrew these 2 nuts to remove the clutch V-belt cover. NEVER operate the saw with this cover removed. It may be necessary to remove the pulley cover first before this cover can be removed.

9. Decompression Valve – Push inward when starting engine.

10. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture.

11. Rear Handle – When starting engine, place right foot onto rear handle base. For normal operation always place one hand on the rear handle and the other hand on the upper handle. Always use two hands when operating the saw.

6. V-belt Cover (Pulley) – Unscrew these 3 nuts to remove the pulley V-belt cover. NEVER operate the saw with this cover removed.

PAGE 14 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

12. Engine ON/OFF Switch – ON position permits engine starting, OFF position stops engine operation.

HS62A CUT-OFF SAW — CONTROLS & COMPONENTS

21 20 19

Figure 3. HS62A Cut-off Saw Components 2

13. Blade Guard – Covers saw blade.

14. Front Handle – When lifting or carrying of the saw is required, use this handle.

15. Throttle Lock Lever – Using your thumb, press this lever downward and squeeze the trigger lever to lock the throttle in place. Use this option only to aid starting. Squeeze the trigger lever again to unlock the throttle.

16. Throttle Trigger Lock-out – Press this lever downward to allow throttle trigger activation.

17. Throttle Trigger Lever – Squeeze this lever to start the saw blade rotation. Release the trigger lever to stop the saw blade rotation. This lever is to be used in conjunction with either the throttle lock or variable throttle levers.

18. Fuel Filler Cap – Remove this cap to add mixed fuel

19. Recoil Starter (pull rope) – Manual-starting method. Pull

20. Blade Shaft Nut – Loosen to remove the cutting blade

21. Cutting Blade – Use appropriate type blades for desired

22. Spark Plug – Provides spark to the ignition system. Set

(requires a 50:1 mixture) to the fuel tank. This saw uses a 2-stroke engine. Make sure fuel cap is tightened securely. DO NOT over fill. See Figure 13 for correct fuel to oil mixture.

the starter grip until resistance is felt, then pull briskly and smoothly.

from the outer and inner flanges.

cutting application.

spark plug gap to 0.02 inch (0.5 mm). Clean spark plug once a month.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 15

HS62A CUT-OFF SAW — BLADE INSTALLATION INSTRUCTIONS

Figure 4. Tool Kit

Blade Installation Procedure

STEP 1

For proper installation, first remove the

outer

flange Y, and

inner

“dual-arbor” flange Z.

blade shaft nut

The Multiquip (Figure 4) that assists you with day to day operations. need these tools for the assembly of your saw.

Item

common bolt/screw and nut head sizes of your saw.

Item

allen screws.

STEP 3

Chose the proper your cutting blade arbor) and place this selected side to the

blade shaft

Side Winder

is a versatile screwdriver/wrench that accommodates

is the wrench necessary to accommodate various

blade arbor

[

Cut-Off Saw comes with a Tool Kit

side of the

inner flange

(to match

You will

Figure 5. Inner and Outer Flanges (Removal)

STEP 2

A dual sided, “dual-arbor” a 20 mm or 1-inch arbor hole for operator safety and convenience.

The

outer flange

Figure 6. Inner and Outer Flanges (Placement)

PAGE 16 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

inner flange

fits on top of the cutting blade.

Zaccommodates either

Figure 7. Selecting the Proper Blade Arbor

STEP 4

Match the arbor side to the dimension of your blade arbor and “sandwich” between the inner and outer flanges. Tighten the

blade shaft nut

securely to hold the blade in place.

Figure 8. Securing the Cutting Blade

HS62A CUT-OFF SAW — WATER KIT INSTALLATION INSTRUCTIONS

Contents of Water Kit

The contents of the Water Kit cannot be purchased seperately.

See Water Kit Assembly in Parts Section of this manual for

Water Kit part number.

Figure 9. Water Kit Parts

Hose Clamp

Socket Head Cap Screw w/ Washer

Quick Disconnect Fitting

Water Hose

Hex Key Tool K (Included with Tool Kit)

Plastic Ties

Wet

Air Filter Canister

Water Kit Installation Procedure

Connect the



single end of the

Snap fit the

Blade Guard

Front Handle.

Loop the

and fasten the clamp to the

M (Sold Seperately)

Quick Disconnect Fitting

Water Hose

. Orient the

Hose Clamp

Outlets J to the

Water Hose

around the

Roller Bar Support Arm

I to the

Holes

in the

through the

Water Hose

using the Socket Head Cap Screw w/ Washer H, and

Figure 10. Water Kit Assembly Points

Figure 11. Wet Air Filter Canister

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 17

Hex Key Tool

Use the

the hose fittings and water hose to the saw.

When using the Water Kit option for your saw, the Dry

Filter Canister

Canister

Section of this manual).

Plastic Ties

M (See Air Filter Kit Assembly in Parts

as preferred to further secure

MUST be replaced with the Wet

Air Filter

Air

HS62A CUT-OFF SAW — BLADES

PREPARATION / PRE-INSPECTION

1. Read and fully understand this manual, the safety instructions in particular, and the engine manufacturer's manual supplied with the saw.

2. Select the correct blade for each application. If abrasive blades are used, MAKE CERTAIN they are designed for use on a concrete floor saw. They must be reinforced and have a hole for the driving pin. When wet cutting with an abrasive blade, MAKE CERTAIN the blade is intended for wet cutting. Water will destroy a dry cut abrasive blade. Some diamond blades require water cooling and failure to do so will destroy them almost immediately. Other diamond blades can be used with or without water.

3. Handle all blades with care and NEVER use a damaged blade. NEVER use an abrasive blade that has been dropped.

BLADES

Saw blades, or cutting disks, are available in either an abrasive design or as diamond blades. Either blade will work on the HS62A CUT-OFF SAW , however, diamond blades are recommended. Ask your dealer about your specific cutting application.

SAW BLADE INSPECTION

WARNING

Failure to thoroughly inspect the diamond blade (Figure 12) for operational safety could result in damage to the blades or the saw and may cause injury to the user or others in the operating area.

1. Stress Relief Holes (Gullets) - Check the steel core for cracks that may have propagated from the slots and/or gullets. Cracks indicate extreme fatigue failure and if sawing continues, catastrophic failure will occur.

2. Edge of the Steel Core - Check the diameter edge for discoloration (blue oxidation) indicating an overheating condition caused by insufficient cooling water/air. Overheating of blades may lead to loss of core tension and/ or increase the possibility for blade failure. Make sure the steel core's width is uniform about the rim of the blade, and not succumbing to an "under-cutting" condition brought about by highly abrasive material or improper under-cutting core protection

3. Directional Arrow - Ensure that the blade is oriented properly on the blade shaft for sawing. Reference the directional arrow on the blade and place it so the direction of rotation "downcuts" with the turn of the shaft.

4. Diamond Segment or Rim - Ensure there are no cracks, dings, or missing portions of the diamond segment/rim. DO

NOT

of the rim.

cause damage to your saw or injury to the user or others in the operating area.

5. Specifications - Ensure that the blade specifications, size, and diameter properly match up to sawing operations. Utilizing a blade not matched properly to the task may result in poor performance and/or blade damage.

6. Arbor Hole - It is essential that the arbor hole diameter properly matches the blade, and that it is free from distortion. Correct blade flanges (collars) must be used. The inside face of the flanges must be clean and free of debris. An outof-round arbor condition will cause damage to the blade and the saw.

7. MAX RPM - This RPM reference is the maximum safe operating speed for the blade selected. NEVER exceed the max RPM on the diamond blade. Exceeding the maximum RPM is dangerous and may cause poor performance and may damage the blade.

Figure 12. Diamond Blade

use a blade that is missing a segment or a portion

Damaged and /or missing segments/rims may

PAGE 18 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — INITIAL START-UP/OPERATION

INITIAL START-UP

CAUTION

DO NOT attempt to operate the saw until the Safety, General

Information and Inspection sections of this manual have been read and thoroughly understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual.

CAUTION

NEVER operate the saw in a confined area

or enclosed area structure that does not provide ample

ALWAYS wear approved eye and hearing protection before operating the saw.

NEVER place hands or feet inside the belt guard or blade guard while the engine is running. ALWAYS shut the engine down before performing any kind of maintenance service on the saw.

free flow of air

Explosive Fuel

Fuel Check

Figure 13. Fuel to Oil Mixture

For correct fuel to oil mixture, add 2.6 fl. oz (29.6 ml) of 2-stroke motor oil to 1 gallon (3.8

NOTE

liters) of

gasoline

unleaded gasoline add 13 fl. oz (384 ml) of

2-stroke motor oil.

A bottle ( 2.6 fl. oz) of smokeless 2-stroke motor oil

purchased separately

be purchased. When ordering use Multiquip P/N 00325.

Starting

1. Place the engine ON/OFF switch in the ON position

2. Using your thumb, press down on the throttle lock lever,

while squeezing the throttle trigger. This will lock the throttle

half-throttle

in the

3. Pull the choke lever all the way out to the CLOSED position.

premium 92 octane unleaded

. For a

5 gallon

can of

premium

cannot be

. Only a case of 36 individual bottles can

position.

Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. DO NOT attempt to refuel the saw if the engine is

1. Remove the fuel cap located on the side of the saw.

2. Visually inspect to see if fuel level is low. If fuel is low, replenish with fuel oil mixture as shown in Figure 13.

3. When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel.

NOTE

hot! or running

This saw uses a 2-stroke engine which requires a mixture of unleaded gasoline and smoke free 2-stroke motor oil. See Figure 13.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 19

premium

92 octane

4. Pull the

5. Place the saw on level ground. Make sure the saw blade is free to rotate and will not come into contact with any foreign objects.

6. Hold the front handle firmly with the left hand and put your right foot onto the base of the rear handle.

NOTE

decompression button

The CLOSED position of the choke lever enriches the fuel mixture for starting a COLD engine. The OPEN position provides the correct fuel mixture for normal operation after starting, and for restarting a warm engine.

inward.

HS62A CUT-OFF SAW — INITIAL START-UP/OPERATION

7. Grasp the becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting.

8. If the engine has started, slowly return the choke lever to the

"OPEN"

1 through 9.

9. Squeeze the throttle lever trigger to release it from the throttle position.

10. Before the saw is placed into operation, run the engine for several minutes. Check for fuel leaks, and noises that would associate with a loose guards and/or covers.

OPERATION

WARNING

ALWAYS cut with the saw at FULL THROTTLE. Attempting

to cut with the saw at less than full throttle could cause the blade to bind or stop abruptly in the slab resulting in serious injury to the operator or others in the area.

starter grip

position. If the engine has not started repeat steps

and slowly pull it out. The resistance

NOTE

4. When the end of the cut has been reached, raise the blade out of the cut .

half-

5. If cutting is complete, turn the engine off and wait for the blade to stop rotating.

Shut-down

1. Let the engine idle for 3-5 minutes.

2. Place the engine ON/OFF switch to the OFF position

3. Wait for the blade to stop spinning before handling the saw.

4. DO NOT touch the cutting blade it is very cool, severe burn condition exists.

Mark the cutting line clearly and always saw in a STRAIGHT LINE ONLY.

hot!

, allow it to

WARNING

ALWAYS keep clear of

operating this equipment.

2. To begin sawing, lower the rotating blade allowing it to cut to the preset depth.

3. When blade has reached full cutting depth, slowly walk behind the saw at a rate that will allow the engine to operate without losing optimum RPM.

rotating

moving

parts while

CAUTION

DO NOT try to cut faster than the blade will allow. Cutting

too fast will cause the blade to rise up out of the cut. Improper cutting rate can decrease the life of the engine and blades.

PAGE 20 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

V-Belt Changing Procedure

HS62A CUT-OFF SAW — MAINTENANCE

Figure 14. Belt Guard Cover Removal

Figure 15. Re-Installing Cover Guard

Remove the 2 hex nuts gain access to the V-belt on the clutch side. Remove V-belt

cover

Remove the 2 hex nuts

knob

the Cover Guard

to gain access to the V-belt on the spindle side. Remove

and hex screw and washer M to

and hex screw and guard adjustment

Using the provided wrench, loosen the three nuts the tension on the V-belt, then turn the V-belt Tensioning Cam

until the V-belt is completely slacked.

Figure 16. V-Belt Tensioning

Remove the V-belt Install the new V-belt around both pulleys. It is essential that the

drive V-belt is properly positioned around both the clutch and spindle pulleys.

Figure 17. Drive V-Belt

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 21

from the

clutch and spindle pulleys

to reduce

V-Belt Changing Procedure (continued)

HS62A CUT-OFF SAW — MAINTENANCE

Figure 18. Reversing the Cutting Arm

Re-tension the V-belt by turning the The V-belt should remain in tension.

Fully tighten the three nuts tensioning position.

Re-install the

the two cap screws

guard

and

and reinstall the adjustment knob I.

belt tensioning cam

that lock the V-belt into the proper

V-belt Tcovers

. Fully tighten

Figure 19. Re-Installing Cover Guard

PAGE 22 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

Reversing the Cutting Arm Procedure

HS62A CUT-OFF SAW — MAINTENANCE

NOTE

This assembly procedure permits the operator to reorient the and/or object.

Figure 20. Tool Kit

cutting blade

The Multiquip (Figure 16) that assist you with day to day operations. You will need these tools for the maintenance of your saw.

Item

common bolt/screw and nut head sizes of your saw.

Item

screws.

This position displays the cutting position. To reverse the blade position continue with the following steps:

Remove the following items from the to expose the V-belt:

Side Winder

is a versatile screwdriver/wrench that accommodates

is the wrench necessary to accommodate various allen

Cut-Off Saw comes with a Tool Kit

cutting blade on the inside

closer to a wall, column

(center)

Cutting Arm Assembly

Figure 21. Inside Center Cutting Position

Figure 22. Belt Tensioning Cam

■

Loosen the

nuts reverse the

belt tensioning cam

. This will take tension off the V-belt, and permit you to

cutting arm

Guard Adjustment Knob

Two Cap Screws

Cover Guard

and remove the three

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 23

HS62A CUT-OFF SAW — MAINTENANCE

Reversing the Cutting Arm Procedure (continued)

Figure 23. Reversing the Cutting Arm

Reverse the 23, and re-tension the V-belt by turning the

cam

Fully tighten the three nuts tensioning position.

Re-attach the

and reconnect the

cutting arm

. The V-belt should remain in tension.

cover guard

180 degrees as shown in the Figure

that lock the V-belt into the proper

Kwith the 2 cap screws J,

guard adjustment knob

belt tensioning

Figure 24. Re-attaching Cover Guard

PAGE 24 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — MAINTENANCE (AIR/FUEL FILTER)

Air/Fuel Filter Maintenance Procedures

Figure 25. Fuel Filter

Figure 26. Pre-Filter

Check the for dirt/debris build up. It is recommended to change the fuel filter

every

This engine is a 2-stroke gasoline engine

fuel to oil mixture of 50:1(2%). It is recommended to use an unleaded gasoline rated at 92 octane ( use on 2-stroke engines only. See Figure 13.

It is highly recommended to keep a supply of spare on hand. Maintaining the will prolong the life of the

Every 8 hours of operation

water. Let dry thoroughly. When dry, completely coat the filter with only an approved

fuel filter

50 tanks of fuel

and wash the foam

located inside the fuel tank periodically

foam pre -filter

main filter element

pre-cleaner

foam filter oil

premium)

, and regular exchanges

, remove the

pre-air cleaner cover

H in warm fresh soapy

requiring a specific

with an oil for

pre-filters

Every 8 hours of operation

and inspect the

element

soft brush. DO NOT air blast clean this element with compressed gas.

Figure 27. Main Filter Element

Figure 28. Supplementary Filter

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 25

The main filter element should be replaced after

changes

Every 8 hours of operation, inspect the

element

vigorously shaking out and dusting off with a soft brush. DO NOT air blast clean this element with compressed gas.

The

three pre filter changes

Kby vigorously shaking out and dusting off with a

L. Clean the

supplementary filter element

main filter element

, remove the

supplementary filter element

covers

. Clean the

supplementary filter

should be replaced after

Iand

main filter

three pre filter

L by

HS62A CUT-OFF SAW — TROUBLESHOOTING (BLADE)

GNITOOHSELBUORTEDALB.3ELBAT

MOTPMYS MELBORPELBISSOP NOITULOS

gnieblairetamehtrofdrahootedalB

?tuc

foesuacebdehsinimideuqrotenignE

?tleb-Vesool

.gnittucspotsroswolsedalB

thgiartstuctonseodedalB

.eurtro/dna

?gnittuc

?rewopenignetneiciffusnI .gnitteselttorhtkcehC

?tucgnieblairetam

?segnalfdnasredluohs

?noitatorfonoitceridreporpmI

?tfahsedalbehtnognippilssiedalB

?wasdengilasimnodesugniebedalB .ytirgetnitnemngiladnasgniraebtfahsedalbkcehC

ehtrofdrahylevissecxesiedalB

?MPRreporpmitadesugniebedalB

robranodetnuomylreporpmiedalB

elihwedalbotdeilppaecrofevissecxE

TONOD dnawolsaylppA.tucehtniedalbehtecrof

.edalbeht"sserdeR"

.stleB-Vecalperro/dnanethgiT

.noitcerid"gnittuC-nwoD"anistniopworra

.tfahsedalbeht

.000,6yletamixorppa

.gniwasnehwecapydaets

gnittucyrT.edalbtcerrocrofpiuqitluMrorelaeDtlusnoC

ot)kcolbrednic,kcirbacilis,enotsdnas(lairetamtfosyrev

lanoitatordnadetneiroylreporpsiedalbehttahtkcehC

nodellatsniylreporperanipegnalf&edalbehttahtkcehC

gnieblairetamehthtiwedalbehtfonoitacificepskcehC

.noitamrofnirofpiuqitluMrorelaeDtlusnoC.tuc

si)MPFS(deepsetunimrepteefecafrusedalberusnE

.tfahsedalbehtnodexiffaylreporpsiedalberusnE

gnieblairetamehtrofdrahootsedalB

?tuc

robranodetnuomylreporpmiedalB

?segnalfdnasredluohs

gniloochguonegniviecertonedalB

gnilkcarc,gnirolocsidedalB

.ylevissecxegniraewro/dna

?riaroretaw

?dnuorfotuoelohrobrA .tfahsedalbehtnodexiffaylreporpsiedalberusnE

lairetamrofnesohcedalbtcerrocnI

?tucgnieb

elihwedalbotdeilppaecrofevissecxE

?gnittuc

TONOD dnawolsaylppA.tucehtniedalbehtecrof

.edalbeht"sserdeR"

.edalbgnittucyrdatuoba

.gniwasnehwecapydaets

PAGE 26 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

gnittucyrT.edalbtcerrocrofpiuqitluMrorelaeDtlusnoC

ot)kcolbrednic,kcirbacilis,enotsdnas(lairetamtfosyrev

.tfahsedalbehtnodexiffaylreporpsiedalberusnE

tewrofdedivorpsiretawfoemulov&wolfreporperusnE

detalucricsiriagnilooctneiciffuserusnE.sedalbgnittuc

gnieblairetamehthtiwedalbehtfonoitacificepskcehC

.noitamrofnirofpiuqitluMrorelaeDtlusnoC.tuc

HS62A CUT-OFF SAW — TROUBLESHOOTING (ENGINE)

)ENIGNE(GNITOOHSELBUORT.4ELBAT

MOTPMYSESUACELBISSOPNOITULOS

?gnigdirbgulpkrapS

?gulpkrapsnotisopednobraC .gulpkrapsecalperronaelC

ontub,elbaliavasileuf",tratsottluciffiD

."gulpkrapstaKRAPS

dna,elbaliavasileuf",tratsottluciffiD

eserpsiKRAPS

."gulpkrapsehttatn

kraps

,elbaliavasileuf",tratsottluciffiD

."lamronsinoisserpmocdnatneserpsi

?noitalusni

ifedoteudtiucrictrohS

?paggulpkrapsreporpmI.pagreporp

?evitcefedliocnoitingI.liocnoitingiecalpeR

?detrohssihctiwsFFO/NO

?epytleufgnorW

?metsysleufnitsudroretaW.metsysleufhsulF

?ytridrenaelcriA .renaelcriaecalper

gulpkrapstneic

.nrowfiecalper

otteS

.hctiws

?ytridstniop,pagkrapsreporpmI

?gnitiucrictrohsronekorberiwgulpkrapS

.stniopnaelc

.gniriw

fhsulF

ronaelC

ronoitalusni,pagkcehC

.gulpkrapsecalper

,noitalusnigulpkrapskcehC

ecalper,gniriwhctiwskcehC

krapstcerrocteS

dnapag

gulpkrapsevitcefedecalpeR

ecalperdna,metsysleu

.leuffoepyttcerrochtiw

?nepOekohC.ekohCesolC

rtorprokcutsevlavtsuahxe/noitcuS.sevlavtaes-eR

?dedu

?nrowrednilycro/dnagnirnotsiP

kraps,elbaliavasileuf",tratsottluciffiD

."wolsinoisserpmocdnatneserpsi

?ylreporpdenethgit

psro/dnateksagdaeH

?degamad

natleufnielbaliavatonleuF .leuffoepyttcerrochtiwlliF

?deggolcretlifleuF.retlifleufecalpeR

.roterubracehttatneserpleufoN

taerbpacknatleuF .packnatleufecalperronaelC

?enilleufniriA.enilleufdeelB

tongulpkrapsro/dnadaehrednilyC

teksaggulpkra

?)ypmeknat(k

?deggolcelohreh

.no

tsip

.gulpkraps

.steksag

ro/dnasgnirnotsipecalpeR

dnastlobdaehrednilyceuqroT

gulpkrapsro/dnadaehecalpeR

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 27

HS62A CUT-OFF SAW — TROUBLESHOOTING (ENGINE)

)DEUNITNOC,ENIGNE(GNITOOHSELBUORT.4ELBAT

MOTPMYSESUACELBISSOPNOITULOS

?naelctonrenaelcriA .renae

reporpsinoisserpmoc"rewopnikaeW"

.erifsimtonseoddna

reporpsinoisserpmoc"rewopnikaeW"

.serifsimtub

staehrevoenignE

apS

?gulpkrapsevitcefeD .gulpkrapsecalperronaelC

?paggulpkrapsreporpmI.

?metsysleufniretaW

?evitcefedliocnoitingI.liocnoitingiecalpeR

?gulpkrapsytriD .gulpkrapsecalperronaelC

?epytleufgnorW

?reporpmieulavtaehgulpkr

?ytridsnifgnilooC.snifgniloocnaelC

.gulpkraps

lcriaecalperronaelC

.roterubracdliubeR

pagreporpotteS

ecalperdnametsysleufhsulF

.leufepyttcerrochtiw

ecalperdna,metsysleufhsulF

.leuffoepyttcerrochtiw

foepyttcerrochtiwecalpeR

.setautculfdeepslanoitatoR?detci

.noitcnuflamretratslioceR

PAGE 28 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

?trid

rtserwolfleuF

mlioceR

?esoolgnirpslaripS.relaeDtlusnoC

dnatsudhtiwdeggolcmsinahce

.sgolcroskael

.retawdna

rofmetsysleuferitnekcehC

paoshtiwylbmessaliocernaelC

HS62A CUT-OFF SAW — FILTER KITS

For



HS62FK1A

[ Includes 1 ea.] HS52020270R- Foam Filter HS018600125R- Paper Filter HS018600056AR - Inner Filter

Side WinderSide Winder

Side Winder

Side WinderSide Winder

HS62A

HS Series Cut-Off Saws

DR Y FIL TER KITS

HS62FK5A

[ Includes 5 ea.] HS52020270R- Foam Filter HS018600125R - Paper Filter HS018600056AR - Inner Filter

HS62FK10A

[ Includes 10 ea.] HS52020270R- Foam Filter HS018600125R - Paper Filter HS018600056AR - Inner Filter

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 29

WET FILTER

* Replaces

Standard Water Kit (provided)

DRY

Air Filter Canister When Using Water &

HS099900778A

[ Includes 1 ea.]

HS62A CUT-OFF SAW — EXPLANATION OF PARTS SECTION REMARKS

The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions.

The contents and part numbers listed in the parts section are subject to change guarantee the availibility of the parts listed.

Sample Parts List:

NO. PART NO. PART NAME QTY. REMARKS

1 12345 BOLT ....................... 1 .... INCLUDES ITEMS W/

2*12347 WASHER, 3/8 IN. .... 1....

3 12348 HOSE .................... A/R .. MAKE LOCALLY

4 12349 BEARING ................ 1 .... S/N 2345B AND ABOVE

NO. Column

Unique Symbols - All items with same unique symbol

, #, +, %, or >) in the number column belong to the same

(

assembly or kit, which is indicated by a note in the “Remarks” column.

Duplicate Item Numbers - Duplicate numbers indicate multiple part numbers are in effect for the same general item, such as different size saw blade guards in use or a part that has been updated on newer versions of the same machine.

NOTE

without notice

WASHER, 1/4 IN. ...........

When ordering a part that has more than one item number listed, check the remarks column for help in determining the proper part to order.

. Multiquip does not

NOT SOLD SEPARATELY MQ-45T ONLY

QTY. Column

Numbers Used - Item quantity can be indicated by a number,

a blank entry, or A/R. A/R (As Required) is generally used for hoses or other parts

that are sold in bulk and cut to length. A blank entry generally indicates that the item is not sold

separately. Other entries will be clarified in the “Remarks” Column.

REMARKS Column

Some of the most common notes found in the “Remarks”

Column are listed below. Other additional notes needed to describe the item can also be shown.

Assembly/Kit

symbol will be included when this item is purchased. Indicated by:

“INCLUDES ITEMS W/(unique symbol)”

Serial Number Break

range where a particular part is used. Indicated by:

“S/N XXXXX AND BELOW” “S/N XXXX AND ABOVE” “S/N XXXX TO S/N XXX”

Specific Model Number Use

only with the specific model number or model number variant listed. It can also be used to show a part is NOT used on a specific model or model number variant.

Indicated by:

“XXXXX ONLY” “NOT USED ON XXXX”

- All items on the parts list with the same unique

- Used to list an effective serial number

- Indicates that the part is used

PART NO. Column

Numbers Used - Part numbers can be indicated by a number,

a blank entry, or TBD. TBD (To Be Determined) is generally used to show a part that

has not been assigned a formal part number at time of publication.

A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarified in the “Remarks” Column.

PAGE 30 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

“Make/Obtain Locally”

purchased at any hardware shop or made out of available items. Examples include battery cables, shims, and certain washers and nuts.

“Not Sold Separately”

purchased as a separate item and is either part of an assembly/kit that can be purchased, or is not available for sale through Multiquip.

- Indicates that the part can be

- Indicates that an item cannot be

HS62A CUT-OFF SAW — SUGGESTED SPARE PARTS

SUGGESTED SPARE PARTS

HS62A SIDEWINDER CUT-OFF SAW

1 to 3 Units

Qty. P/N Description

1 ............ HS52022011A ....... STARTER ASSEMBLY

3 ............ HS098000079R .... ROPE, STARTER

1 ............ HS50140060 ......... HANDLE, ROPE

1 ............ HS098000060A ..... SPRING & CASE, STARTER

6 ............ HS3055118 ........... SPARK PLUG

1 ............ HS50012023AR .... CLUTCH ASSEMBLY

1 ............ HS52022005 ......... FUEL CAP, W/O-RING

3 ............ HS50010218 ......... FILTER, FUEL

1 ............ HS52010092 ......... THROTTLE TRIGGER LEVER

1 ............ HS52010077 ......... THROTTLE LOCK LEVER

1 ............ HS52020037 ......... CHOKE LEVER

1 ............ HS52010022A ....... COVER, BELT GUARD

3 ............ HS3918013 ........... WASHER, BELT COVER

3 ............ HS3914010 ........... NUT, BELT COVER

3 ............ HS52020020 ......... V-BELT

2 ............ HS018600235 ....... FLANGE, ARBOR

2 ............ HS018600236A ..... FLANGE, ARBOR

2 ............ HS52010177 ......... SCREW AND WASHER, ARBOR

2 ............ HS52010062A ....... KNOB, ADJ. GUIDE

2 ............ HS3833080 ........... WASHER, ADJ. GUIDE

2 ............ HS52010045 ......... SPACER, ADJ. GUIDE

2 ............ HS52010013 ......... LOCK, GUIDE BLADE GUARD

1 ............ HS52012024B ....... FLANGE, PRE-FILTER CAP

1 ............ HS52010014B ....... SUPPORT FILTER

2 ............ HS3802002A ......... SCREW, FILTER SUPPORT

1 ............ HS330000010 ....... O-RING, FLANGE PRE-FILTER

1 ............ HS018600090A ..... GASKET, AIR FILTER LOWER

18 .......... HS018600125R .... AIR FILTER

6 ............ HS018600056AR .. FILTER, AIR INNER

18 .......... HS52020270R ...... PRE-FILTER, FOAM

3 ............ HS4191240 ........... TOOL KIT

3 ............ HS099900778A ..... WET, AIR FILTER

3 ............ HS52010082 ......... BREATHER ASSEMBLY

1 ............ 00325 .................... CASE, OIL 2-STROKE NON-SMOKE - 36 BOTTLES

NOTE

The contents of this parts catalog are subject to change without notice.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 31

MUFFLER ASSY.

HS62A CUT-OFF SAW — MUFFLER ASSY.

PAGE 32 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — MUFFLER ASSY.

MUFFLER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

9 HS52010441 MUFFLER ASSEMBLY ............................. 1 ......... INCLUDES ITEMS W/

10 11 HS50010058A GASKET, MUFFLER 1

HS3801052 SCREW 3 HS3033074 WASHER 5 HS50010145 COVER, MUFFLER 1 HS3801045 SCREW 2 HS005100913B SCREW 2 HS3833073 WASHER 2 HS50010198 DEFLECTOR, MUFFLER 1 HS50010197 SCREEN 1

HS097000092A SCREW 2

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 33

RECOIL START ASSY.

HS62A CUT-OFF SAW — RECOIL START ASSY.

PAGE 34 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — RECOIL START ASSY.

RECOIL START ASSY.

NO. PART NO. PART NAME QTY. REMARKS

14 15 16 17 18 19 20 21 22 23 HS097000092A SCREW 4

24 HS52022011A STARTER ASSEMBLY .............................. 1 ......... INCLUDES ITEMS W/

25 26 27

HS50140060 HANDLE, STARTER ROPE 1

HS098000079R ROPE, STARTER 1

HS098000060A SPRING AND CASE, STARTER 1

HS3960017 SCREW 4

HS3960116 SCREW 1

HS50140055 COVER 1

HS3918006 WASHER 1

HS52010439B PULLEY, STARTER 1

HS3908036 SCREW 1

HS52010410 CAP 1

HS50140056 CAP 1

HS52010404 SPACER 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 35

CRANKCASE ASSY.

HS62A CUT-OFF SAW — CRANKCASE ASSY.

PAGE 36 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — CRANKCASE ASSY.

CRANKCASE ASSY.

NO. PART NO. PART NAME QTY. REMARKS

3 HS52010312 PLATE 1 11 HS52020014 GROMMET 1 12 HS52020040 CAP 1 16 HS50010047AR GASKET, CRANKCASE 1

18 HS52020273 CRANKCASE W/ BEARING ASSY ........................ 1 ......... INCLUDES ITEMS W/

19 20 HS52020013 CAP 1 21 HS50010029 GROMMET 1 22 HS3833073 WASHER 7 23 HS006100303 SCREW 2 24 HS097000080BR BAR STUD, CRANKCASE 2 26 HS3801015 SCREW 4 28 HS005100987 SCREW 1 30 HS097000057 GROMMET 1 31 HS52020037 CHOKE LEVER 1 37

HS3034012 BEARING, CRANKCASE 2

HS3023008 PIN 2

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 37

HS62A CUT-OFF SAW — V-BELT COVER (CLUTCH SIDE) ASSY.

V-BELT COVER (CLUTCH SIDE) ASSY

PAGE 38 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — V-BELT COVER (CLUTCH SIDE) ASSY.

V-BELT COVER (CLUTCH SIDE) ASSY.

NO. PART NO. PART NAME QTY. REMARKS

25 HS52020240 V-BELT COVER, (CLUTCH SIDE) 1 31 HS50010148R NUT 2 34 HS3833073 WASHER 3 40 HS3806021A SCREW 2 41 HS3801066 SCREW 1 42 HS52020019 GUARD, BELT INNER 1 43 HS3916008R WASHER 2 44 HS006000300 BUSHING 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 39

HS62A CUT-OFF SAW — V-BELT COVER (PULLEY) /BLADE GUARD ASSY.

V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY.

BLADE FLANGE

INNER (LIP)

BLADE FLANGE

OUTER (FLAT)

CLUTCH

PULLEY

PAGE 40 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — V-BELT COVER (PULLEY) /BLADE GUARD ASSY.

V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 HS52010026 BLADE COVER 14-INCH 1 2 HS52010177 SCREW AND WASHER 1 4 HS52010045 SPACER 1 5 HS018600235 FLANGE, ARBOR (OUTER) 1 6 HS52010044 SPACER 2 7 HS018600019 SHAFT 1 8 HS3806022 SCREW 3 9 HS005000343 WASHER 1 10 HS018600236A FLANGE, ARBOR (INNER) 1 11 HS018100029 O-RING, BLADE GUARD SUPPORT 1 12 HS3035019 BEARING 2 13 HS093000020 SPACER 1 14 HS094000251 NUT 5 15 HS52010039 SPACER 1 16 HS01860004A PULLEY, BELT 1 17 HS3918013 WASHER 1 18 HS3806065 SCREW 1 19 HS52010305 PLATE 17 20 HS3806021 SCREW 5 21 HS52010212 ARM 1 22 HS52010043 FLANGE 1 23 HS52010013 LOCK, GUIDE BLADE GUARD 1 24 HS52010396 GUIDE, BLADE GUARD 1 26 HS52010062 KNOB, ADJUSTMENT GUIDE 1 27 HS3802005A SCREW 2 28 HS52010025A SUPPORT BLADE GUARD 1 29 HS3801016 SCREW 2 30 HS3914010 NUT 3 32 HS52020020 V-BELT 1 33 HS52010022A COVER, V-BELT (PULLEY SIDE) 1 34 HS3833073 WASHER 6 35 HS3806037A SCREW 1 36 HS52010211 GUARD 1 37 HS52010046 BUSHING 1 38 HS52010401 SCREW 1 39 HS52010036 BELT ADJUSTER 1 45 HS3833080 WASHER 1 46 HS3906019 SCREW 1 47 HS52010428 PLASTIC PIN 2

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 41

FUEL TANK ASSY.

HS62A CUT-OFF SAW — FUEL TANK ASSY.

PAGE 42 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — FUEL TANK ASSY.

FUEL TANK ASSY.

NO. PART NO. PART NAME QTY. REMARKS

4 HS52010082 BREATHER 1 5 HS093000448 TUBE 1 6 HS018500066 FITTING 1 8 HS018500096 VALVE BODY 1 9 HS50010093 CLIP 1 15

16 HS52022005 CAP, FUEL ............................................................. 1 ......... INCLUDES ITEM W/

19 HS50010061R SHOCK ABSORBER 1 28 HS50010218 FILTER, FUEL 1 29 HS50010093 TUBE 1 30 HS50140023 GROMMET 1

HS099900090 0-RING 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 43

HS62A CUT-OFF SAW — LIFTING HANDLE AND ROLLER ASSY.

LIFTING HANDLE AND ROLLER ASSY.

PAGE 44 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — LIFTING HANDLE AND ROLLER ASSY.

LIFTING HANDLE AND ROLLER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 HS52020023 HANDLE 1 2 HS018100317 SCREW 4 3 HS3072015 WASHER 2 7 HS3801020 SCREW 2 17 HS52020026 GUARD, FUEL TANK 1 18 HS3960087 SCREW 1 20 HS52010214 MAIN ROLLER SUPPORT UPPER 1 21 HS3960045 SPACER, ROLLER SUPPORT LOWER 2 22 HS018100171A ROLLER 1 23 HS52010098 SUPPORT, ROLLER LOWER 1 25 HS38003035 SCREW 2 26 HS52010066R SHOCK ABSORBER 4 27 HS52020077A FUEL TANK ASSY. 1 29 HS3833076 WASHER 4 30 HS3806035 SCREW 2

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 45

THROTTLE ASSY.

HS62A CUT-OFF SAW — THROTTLE LINKAGE ASSY.

PAGE 46 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — THROTTLE LINKAGE ASSY.

THROTTLE ASSY

NO. PART NO. PART NAME QTY. REMARKS

10 HS52010092 THROTTLE TRIGGER LEVER ............................... 1 ......... INCLUDES ITEM W/ #

11 HS52010077 THROTTLE LOCK LEVER 1 12 HS097000028 SPRING 1 13 HS097000024 COVER, HANDLE/TANK 1 14 HS3960040 SCREW 3

38% CAP, THROTTLE LINKAGE ................................... 1 ......... NOT SOLD SEPARATELY

39 HS52022048A THROTTLE LINKAGE ............................................ 1 ......... INCLUDES ITEM W/ %

40# PLATE .................................................................... 1 ......... NOT SOLD SEPARATELY

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 47

FLYWHEEL COVER ASSY.

HS62A CUT-OFF SAW — FLYWHEEL COVER ASSY.

PAGE 48 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — FLYWHEEL COVER ASSY.

FLYWHEEL COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

3 HS005000361 WASHER, FLAT 1 4 HS3833080 WASHER, LOCK 1 5 HS004000142 NUT 1 6 HS500110019A FLANGE, STARTER 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 49

FLYWHEEL ASSY.

HS62A CUT-OFF SAW — FLYWHEEL ASSY.

PAGE 50 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — FLYWHEEL ASSY.

FLYWHEEL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 HS52020247R FLYWHEEL ................................................ 1 ......... INCLUDES ITEM W/

HS52012027 PAWL SET 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 51

IGNITION COIL ASSY.

HS62A CUT-OFF SAW — IGNITION COIL ASSY.

PAGE 52 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — IGNITION COIL ASSY.

IGNITION COIL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

9 HS052010362 CABLE WIRE 1 10 HS3916004 WASHER 2 11 HS006000315 WASHER 2 12 HS094000227 SCREW 2

13 HS52020148R COIL, IGNITION ASSY. ............................. 1 ......... INCLUDES ITEMS W/

15 HS52010132 CONNECTING LINK 1 16 HS094500497 SWITCH, ON-OFF 1 17 HS097000121A CABLE WIRE, ON-OFF SWITCH 1 18 HS099900397 NUT 1 19 HS004000438 PLATE, ON-OFF SWITCH 1

HS094600169 SPRING SPARK PLUG 1 HS094600097A CAP, SPARK PLUG 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 53

AIR FILTER ASSY.

HS62A CUT-OFF SAW — AIR FILTER ASSY.

PAGE 54 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — AIR FILTER ASSY.

AIR FILTER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 HS52012024B FLANGE, PRE- FILTER, CAP 1 2 HS330000010 O- RING, FLANGE PRE- FILTER 2 3 HS018600125R FILTER, AIR (STANDARD) 1

3A HS099900778A FILTER, AIR (WET CUTTING) .................. 1 ......... OPTIONAL

4 HS018600056AR FILTER, AIR INNER 1 5 HS3802002A SCREW, FILTER SUPPORT 3 6 HS3049007 O-RING 1 7 HS52010014B SUPPORT, FILTER 1 8 HS52020270R PRE- FILTER, FOAM 1 9 HS093000468A SCREW 1 10 HS018600090A GASKET, AIR FILTER LOWER 1 11 HS52020021 GASKET, AIR FILTER BASE 1 12 HS52010016 COVER, AIR FILTER LOWER 1 13 HS072700182 SCREW, AIR CLEANER MTG. 3 14 HS3833073 WASHER, AIR CLEANER MTG. 3 20 HS52022006 COVER, AIR FILTER, UPPER 1 21 HS52010060 GASKET, AIR FILTER COVER 1 22 HS52010041 KNOB, AIR FILTER COVER 1 23 HS52020018 COVER, AIR FILTER, LONG 1 24 HS093000468A SCREW, AIR FILTER COVER 2

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 55

HS62A CUT-OFF SAW — CARBURETOR MOUNTING ASSY.

CARBURETOR MOUNTINGASSY.

PAGE 56 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — CARBURETOR MOUNTING ASSY.

CARBURETOR MOUNTING ASSY.

NO. PART NO. PART NAME QTY. REMARKS

6 HS3833073 WASHER 2 11 HS52020060 SPRING 1 12 HS094000215A TUBE 1 13 HS61052009B SCREW 1 14 HS097000059A SPRING, MANIFOLD 1 15 HS52020008B MANIFOLD, OUTER 1 16 HS50010028 FLANGE 1 17 HS3960057 SCREW 1 18 HS52020271 CARBURETOR ASSEMBLY 1 19 HS018100354 FUEL LINE, CARBURETOR 1 20 HS52020177 SCREW 1 21 HS097000092A SCREW 1 22 HS52020039 SUPPORT, CARBURETOR 1 23 HS50020026 MANIFOLD, INNER 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 57

CARBURETOR ASSY.

HS62A CUT-OFF SAW — CARBURETOR ASSY.

PAGE 58 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — CARBURETOR ASSY.

CARBURETOR ASSY.

NO. PART NO. PART NAME QTY. REMARKS

10 11 12 13 14 15 16 17 18 19 20 21 22 HS50010122A KIT, GASKET CARBURETOR 1 23 HS50010123A KIT, REPAIR CARBURETOR 1 24 25 26 27 28 29

30 HS52020271 CARBURETOR ASSY., HDA225 ............... 1 ......... INCLUDES ITEMS W/

HS50010095 THROTTLE SHAFT 1 HS50010096 STARTER SHAFT 1 HS00300201 SPINDLE 1 HS52020080 COVER, TOP 1 HS52020081 COVER, BOTTOM 1 HS50010099 SHUTTER 1 HS50010100 SHUTTER 1 HS2318839 CLAMP 1 HS2318634 CAP 2 HS380000338 SCREW 1

HS094600148 SPRING 2

HS50010106 SPRING 1

HS50010109 SCREW 1

HS074000240 ADJUST SCREW 1

HS003300209 SCREW 1

HS2318837 SCREW "L" CARBURETOR 1

HS2318838 SCREW "H" CARBURETOR 1

HS035000162 SCREW 4

HS003300202 SCREW 1

HS095000146 SPRING 1

HS094600143 BALL 1

HS2318632 SUPPORT 1

HS50010105 SPRING 1

HS015400153 WASHER 2

HS380000272 SEAL RING 2

HS003300036 FITTING 1

HS2318867 CLAMP 2

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 59

HS62A CUT-OFF SAW — CRANKSHAFT / PISTON ASSY.

CRANKSHAFT AND PISTON ASSY.

PAGE 60 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — CRANKSHAFT AND PISTON ASSY.

CRANKSHAFT AND PISTON ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 HS3055118 SPARK PLUG 1 2 HS005100906A SCREW 4 3 HS3833076 WASHER 4 4 HS50010215 DECOMPRESSOR 1

# HS50020004 PISTON RINGS 1

# HS50010031 PISTON PIN 1

# HS007201198 RING, PISTON PIN 2

9 HS50092028 CYLINDER ASSEMBLY W /PISTON .............. 1 .......... INCLUDES ITEMS W /

10 HS50010046B GASKET, CYLINDER 1 13 HS3037014 BEARING, UPPER CRANKSHAFT 1 14 HS50090001R CRANKSHAFT 1 15 HS094500028R KEY, CRANKSHAFT 1 17 HS094500004 SEAL RING 1 25 HS007201313 SEAL RING, CRANKSHAFT 1

27 HS50012023AR CLUTCH ASSEMBLY ..................................... 1 .......... INCLUDES ITEMS W /

29+ HS004900137B SPRING, CLUTCH 1 32 HS097000097 WASHER 1 33$ HS52010030 BEARING 1 34 HS52010035 SPACER, CLUTCH DRUM 1 35 HS52010034 BUSHING, CLUTCH DRUM 1

36 HS52010029R CLUTCH DRUM ............................................ 1 .......... INCLUDES ITEMS W /$

HS50092013 PISTON ASSEMBLY W /RINGS ..................... 1 .......... INCLUDES ITEMS W /#

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 61

WATER KIT ASSY.

HS62A CUT-OFF SAW — WATER KIT ASSY.

PAGE 62 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — WATER KIT ASSY.

WATER KIT ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 3 4 5 6 7

HS52012062 WATER KIT ASSY. ....................................................... 1 .......... INCLUDES ITEMS W /

HS52010121 FITTING, QUICK DISCONNECT 1

* * * * *

HS52010207 VALVE, SHUT-OFF 1

NOTE

PLASTIC TIE WRAPS .................................................. 8 .......... NOT SOLD SEPARATELY

HOSE CLAMP ............................................................. 1.......... NOT SOLD SEPARATELY

SCREW, SOCKET HEAD CAP W/ WASHER ...............1 .......... NOT SOLD SEPARATELY

HOSE, WATER ............................................................ 1 .......... NOT SOLD SEPARATELY

Items 3-6 are included with the Water Kit Assembly and cannot be purchased separately.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 63

TOOLS

HS62A CUT-OFF SAW — TOOLS

PAGE 64 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

HS62A CUT-OFF SAW — TOOLS

TOOLS

NO. PART NO. PART NAME QTY. REMARKS

2 00325 SMOKELESS 2-STROKE OIL....... 1 ............. CAN ONLY BE PURCHASED AS A CASE (QTY 36)

HS4191240 TOOL KIT 1

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 65

HS62A CUT-OFF SAW — RECOMMENDED DIAMOND BLADES

Recommended Diamond Blades

Blade

Type

GES

GPS

GPSA

SBL

SBLA

PDHS1

PDHS1A

PDHS2

PDHS2A

SW2

SW2G

Asphalt

for Your Saw

Green

Concrete

Light

Weight

Block

Side Winder

Concrete

Block

Cured

Concrete

Standard

Red Brick

Concrete

(Brick)

Pavers

GES

GPS

GPSA

SBL

SBLA

PDHS1

PDHS1A

PDHS2

PDHS2A

SW2

SW2G

SW2

Soft

Stone

Medium

Stone

Hard

Stone

PDHS3

PDHS3A

SDW

SWG

HSC

HSG

PVL

KBL

BBL

GET

GPT

TBL

PDHS3

PDHS3A

SDW

SWG

HSC

HSG

PVL

KBL

BBL

GET

GPT

TBL

PAGE 66 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

Effective: February 22, 2006

TERMS AND CONDITIONS OF SALE — PARTS

PAYMENT TERMS

Terms of payment for parts are net 30 days.

FREIGHT POLICY

All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier.

MINIMUM ORDER

The minimum charge for orders from Multiquip is $15.00 net. Customers will be asked for instructions regarding handling of orders not meeting this requirement.

RETURNED GOODS POLICY

Return shipments will be accepted and credit will be allowed, subject to the following provisions:

1. A Returned Material Authorization must be approved by Multiquip prior to shipment.

2. To obtain a Retur n Material Authorization, a list must be provided to Multiquip Parts Sales that defines item numbers, quantities, and descriptions of the items to be returned.

a. The parts numbers and descriptions

must match the current parts price list.

b. The list must be typed or computer

generated.

c. The list must state the reason(s) for

the return.

d. The list must reference the sales

order(s) or invoice(s) under which the items were originally purchased.

e. The list must include the name and

phone number of the person requesting the RMA.

3. A copy of the Return Material Authorization must accompany the return shipment.

4. Freight is at the sender’s expense. All parts must be returned freight prepaid to Multiquip’s designated receiving point.

5. Parts must be in new and resalable con-

6. The following items are not returnable:

7. The sender will be notified of any material

8. Such material will be held for five working

9. Credit on returned parts will be issued at

10. In cases where an item is accepted, for

11. Credit issued will be applied to future

PRICING AND REBATES

Prices are subject to change without prior notice. Price changes are effective on a specific date and all orders received on or after that date will be billed at the revised price. Rebates for price declines and added charges for price increases will not be made for stock on hand at the time of any price change.

Multiquip reserves the right to quote and sell dition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked.

a. Obsolete parts. (If an item is in the

price book and shows as being replaced by another item, it is obsolete.)

b. Any parts with a limited shelf life

(such as gaskets, seals, “O” rings, and other rubber parts) that were purchased more than six months prior to the return date.

c. Any line item with an extended dealer

net price of less than $5.00.

d. Special order items.

e. Electrical components. f. Paint, chemicals, and lubricants.

g. Decals and paper products.

h. Items purchased in kits.

received that is not acceptable.

days from notification, pending instructions. If a reply is not received within five days, the material will be returned to the sender at his expense.

dealer net price at time of the original purchase, less a 15% restocking charge.

which the original purchase document can not be determined, the price will be based on the list price that was effective twelve months prior to the RMA date.

purchases only.

direct to Government agencies, and to Original

Equipment Manufacturer accounts who use

our products as integral parts of their own

products.

SPECIAL EXPEDITING SERVICE

A $35.00 surcharge will be added to the invoice

for special handling including bus shipments,

insured parcel post or in cases where Multiquip

must personally deliver the parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITY

Multiquip shall not be liable hereunder for

damages in excess of the purchase price of the

item with respect to which damages are

claimed, and in no event shall Multiquip be

liable for loss of profit or good will or for any

other special, consequential or incidental dam-

ages.

LIMITATION OF WARRANTIES

No warranties, express or implied, are made

in connection with the sale of parts or trade

accessories nor as to any engine not manufac-

tured by Multiquip. Such warranties made in

connection with the sale of new, complete units

are made exclusively by a statement of war-

ranty packaged with such units, and Multiquip

neither assumes nor authorizes any person to

assume for it any other obligation or liability

whatever in connection with the sale of its

products. Apart from such written statement of

warranty, there are no warranties, express,

implied or statutory, which extend beyond the

description of the products on the face hereof.

HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (10/20/06) — PAGE 67

OPERATION & PARTS MANUAL

HERE'S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER

UNITED STATES

Multiquip Corporate Office MQ Parts Department

18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877 Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284 Contact: mq@multiquip.com

Mayco Parts Warranty Department

800-306-2926 Fax: 800-672-7877 800-421-1244, Ext. 279 Fax: 310-537-1173 310-537-3700 Fax: 310-637-3284 310-537-3700, Ext. 279

Service Department Technical Assistance

800-421-1244 Fax: 310-537-4259 800-478-1244 Fax: 310-631-5032 310-537-3700

MEXICO UNITED KINGDOM

MQ Cipsa Multiquip (UK) Limited Head Office

Carr. Fed. Mexico-Puebla KM 126.5 Tel: (52) 222-225-9900 Hanover Mill, Fitzroy Street, Tel: 0161 339 2223 Momoxpan, Cholula, Puebla 72760 Mexico Fax: (52) 222-285-0420 Ashton-under-Lyne, Fax: 0161 339 3226 Contact: pmastretta@cipsa.com.mx Lancashire OL7 0TL

CANADA BRAZIL

Multiquip Multiquip

4110 Industriel Boul. Tel: (450) 625-2244 Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055 Laval, Quebec, Canada H7L 6V3 Fax: (450) 625-8664 Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055

Contact: jmartin@multiquip.com Contact: cnavarro@multiquip.com.br, srentes@multiquip.com.br

ON-HAND

WHEN CALLING

Contact: sales@multiquip.co.uk

Multiquip Inc. and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.

Your Local Dealer is:

HS62A Cut-Off Saw.

MULTIQUIP SideWinder HS62A Parts Manual

Specifications and Main Features

Frequently Asked Questions

User Manual