Multiquip PS706020, PS706036, PS706030, PS706026, PS706016 User Manual

PARTS MANUAL

STAY-LEVEL HANDLEBAR SERIES

MODELS

PS706016 PS706020 PS706026 PS706030 PS706036

PAVEMENT SAW

(DEUTZ BF3L2011 DIESEL ENGINE)

Revision #8 (07/26/10)

To find the latest revision of this

publication, visit our website at:

www.multiquip.com

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

P/N 37558

PROPOSITION 65 WARNING

Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are:

Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfrom chemically treatedlumber.

Your risk from these exposures varies, dependingonhowoftenyoudothistype of work. To reduce your exposure to these chemicals: work in aALWAYS well ventilated area, and work with

approved safety equipment, such as

dust masks that are specially designed to filter out microscopic particles.

PAGE 2 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

SILICOSIS/RESPIRATORY WARNINGS

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, California and some other authorities have listed respirable crystalline silica as a substance known to cause cancer. When cutting such materials, always follow the respiratory precautions mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, or other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow the recommendations of the manufacturers or suppliers, OSHA/NIOSH, and occupational and trade associations. Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the materials being used.

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 3

PS7060 SERIES SAWS

Proposition 65 Warning .................................................. 2

Silicosis/Respiratory Warnings ...................................... 3

Table of Contents ........................................................... 4

Parts Ordering Procedures ............................................ 5

Explanation of Code in Remarks Column ...................... 6

Suggested Spare Parts ................................................. 7

Nameplates and Decals ............................................. 8-9

Control Panel Decals .............................................. 10-11

Electrical Control Assembly ................................... 12-13

Console Mounts Assembly ..................................... 14-15

Rear Console Access Panel Assembly .................. 16-17

Light Connector/Dash Access Assembly ............... 18-19

Belt and Engine Guards Assembly ......................... 20-21

Depth Indicator/Stop Switch Assy. (Old Style) ....... 22-23

Depth Indicator/Stop Switch Assy. (New Style) ...... 24-25

F-N-R Assembly ..................................................... 26-27

Fuel Assembly ....................................................... 28-29

Battery Assembly ................................................... 30-31

Stay-Level Handlebars Assembly .......................... 32-33

Handlebar Boot Assembly ...................................... 34-35

Water System Assembly ........................................ 36-37

Engine Assembly ................................................... 38-39

Throttle Control Assembly ...................................... 40-41

Engine Mounts Assembly ...................................... 42-43

Air Cleaner Assembly ............................................. 44-45

Muffler Assembly ................................................... 46-47

Lift Bail Assembly .................................................. 48-49

Platform Guards/Rear Pointer Assembly ................ 50-51

Wheel Drive Assembly ........................................... 52-53

Front Axle Assembly .............................................. 54-55

Hydraulic System Assembly .................................. 56-57

Engine Pivot Cylinder Assembly ............................ 58-59

Hydraulic Hoses Assembly .................................... 60-61

Hydraulic Fttings and Clamps Assembly ................ 62-63

Front Pointer Assembly .......................................... 64-65

Belt Drive Assembly ............................................... 66-69

Drive Pulley Assembly ........................................... 70-71

Bladeshaft Assembly ............................................. 72-73

16", 20", 26" Bladeguard Assembly ...................... 74-75

30", 36" Bladeguard Assembly .............................. 76-77

Optional Weight Kit Assembly ................................ 78-79

TABLE OF CONTENTS

NOTICE

Specification and part number are subject to change without notice.

Terms and Conditions of Sale — Parts........................ 80

PAGE 4 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

PARTS ORDERING PROCEDURES

Ordering parts has never been easier!

Choose from three easy options:

January 1

Effective:

, 2006

Best Deal!

Order via Internet

Order parts on-line using Multiquip’s SmartEquip website!

N View Parts Diagrams N Order Parts N Print Speciﬁcation Information

Goto www.multiquip.com and click on

Order Par ts

Order via Fax

All customers are welcome to order parts via Fax. Domestic (US) Customers dial: 1-800-6-PARTS-7 (800-672-7877)

Non-Dealer Customers: Contact your local Multiquip Dealer for parts or call 800-427-1244 for help in locating a dealer near you.

(Dealers Only)

to log in and save!

(Dealers Only)

Order via Phone:

If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip.

com.

To obtain an MQ Account, contact you District Sales Manager for more information.

Use the internet and qualify for a 5% Discount on Standard orders for all orders which include complete part numbers.*

Note: Discounts Are Subject To Change

Domestic (US) Dealers Call:

1-800-427-1244

Fax your order in and qualify for a 2% Discount on Standard orders for all orders which include complete part numbers.*

Note: Discounts Are Subject To Change

International Customers should contact their local Multiquip Representatives for Parts Ordering information.

R Dealer Account Number R Dealer Name and Address R Shipping Address (if different than billing address) R Return Fax Number R Applicable Model Number R Quantity, Part Number and Description of Each Part

www.multiquip.com

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 5

When ordering parts, please supply:

R Specify Preferred Method of Shipment: UPS/Fed Ex DHL

N Priority One Truck  N Ground N Next Day N Second/Third Day

NOTICE

All orders are treated as Standard Orders and will

ship the same day if received prior to 3PM PST.

WE ACCEPT ALL MAJOR CREDIT CARDS!

EXPLANATION OF CODE IN REMARKS COLUMN

The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions.

NOTICE

The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed.

SAMPLE PARTS LIST

NO. PART NO. PART NAME QTY. REMARKS

1 12345 BOLT ......................1 .....INCLUDES ITEMS W/%

2% WASHER, 1/4 IN. ...........NOT SOLD SEPARATELY

2% 12347 WASHER, 3/8 IN. ...1 .....MQ-45T ONLY

3 12348 HOSE ..................A/R ...MAKE LOCALLY

4 12349 BEARING ..............1 .....S/N 2345B AND ABOVE

NO. Column

Unique Symbols — All items with same unique

symbol

QTY. Column

Numbers Used — Item quantity can be indicated by a

number, a blank entry, or A/R.

A/R (As Required) is generally used for hoses or other parts that are sold in bulk and cut to length.

A blank entry generally indicates that the item is not sold separately. Other entries will be clariﬁed in the “Remarks” Column.

REMARKS Column

Some of the most common notes found in the “Remarks” Column are listed below. Other additional notes needed to describe the item can also be shown.

Assembly/Kit — All items on the parts list with the same unique symbol will be included when this item is purchased.

Indicated by:

“INCLUDES ITEMS W/(unique symbol)”

(@, #, +, %, or >) in the number column belong to the same assembly or kit, which is indicated by a note in the “Remarks” column.

Duplicate Item Numbers — Duplicate numbers indicate multiple part numbers, which are in effect for the same general item, such as different size saw blade guards in use or a part that has been updated on newer versions of the same machine.

NOTICE

When ordering a part that has more than one item number listed, check the remarks column for help in determining the proper part to order.

PART NO. Column

Numbers Used — Part numbers can be indicated by a

number, a blank entry, or TBD.

TBD (To Be Determined) is generally used to show a part that has not been assigned a formal part number at the time of publication.

A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clariﬁed in the “Remarks” Column.

Serial Number Break — Used to list an effective serial number range where a particular part is used.

Indicated by:

“S/N XXXXX AND BELOW” “S/N XXXX AND ABOVE” “S/N XXXX TO S/N XXX”

Speciﬁc Model Number Use — Indicates that the part is used only with the speciﬁc model number or model number variant listed. It can also be used to show a part is NOT used on a speciﬁc model or model number variant.

Indicated by:

“XXXXX ONLY” “NOT USED ON XXXX”

“Make/Obtain Locally” — Indicates that the part can be purchased at any hardware shop or made out of available items. Examples include battery cables, shims, and certain washers and nuts.

“Not Sold Separately” — Indicates that an item cannot be purchased as a separate item and is either part of an assembly/kit that can be purchased, or is not available for sale through Multiquip.

PAGE 6 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

SUGGESTED SPARE PARTS

SS7060 SANDERS SAW

1 TO 3 UNITS WITH DEUTZ TURBO DIESEL ENGINE

Qty. P/N Description

1 ....... 37094 .................. SWITCH, TOGGLE F-N-R

1 ....... 37203 .................. SWITCH, ROLLER PLUNGER

2 ....... 406000 ................ SWITCH, ROCKER

2 ....... 37132 .................. FRONT WHEEL ASSEMBLY

2 ....... 37095 .................. REAR WHEEL

1 ....... 29509 .................. CAP, FUEL TANK

2 ....... 560017 ................ GRIPS, HANDLEBAR

1 ....... H9406 .................. BULB, GE H9406

1 ....... 15503 .................. KNOB, COMFORT

1 ....... 37311 .................. BALL VALVE, WATER SYSTEM

2 ....... 570005 ................ CLAMP, MUFFLER

2 ....... 37048 .................. SPRING, WHEEL DRIVE

2 ....... 582012 ................ BUSHING, QD

2 ....... 915316 ................ SCREW, 5/8 - 11 X 3 LH GR8

2 ....... 915315 ................ SCREW, 5/8 - 11 X 3 GR8

1 ....... 574003 ................ ROPE, POINTER

1 ....... 37212 .................. THROTTLE ASSEMBLY

2 ....... 200019 ................ MUDFLAP, BLADEGUARD

FOR SAWS WITH 16", 20", AND 26" BLADEGUARDS

2 ....... 37168 .................. FLANGE, INNER 5.0"

2 ....... 37169 .................. FLANGE ASSEMBLY, OUTER 5.0"

2 ....... 926790 ................ PIN, DOWEL

2 ....... 362000 ................ HOSE, WATER #6LP (16" BLADEGUARD)

2 ....... 362005 ................ HOSE, WATER #6LP (20" BLADEGUARD)

2 ....... 362006 ................ HOSE, WATER #6LP (26" BLADEGUARD)

ENGINE PARTS FOR DEUTZ TURBO DIESEL ENGINE

2 ....... 1174416 .............. OIL FILTER, DEUTZ BF3L2012

2 ....... 304010 ................ FUEL FILTER, DEUTZ BF3L2011

2 ....... P772579 .............. PRIMARY AIR FILTER ELEMENT

2 ....... P775300 .............. SAFETY AIR FILTER, DEUTZ BF3L2014

2 ....... 21004-003 ........... FAN BELT, AX-35

2 ....... 520007 ................ DRIVE BELT, 5G 3VX-530

1 ....... 406017 ................ IGNITION SWITCH, W/KEY

2 ....... 406017-1 ............. KEY, IGNITION

2 ....... 306006 ................ FILTER, TRANSMISSION

FOR SAWS WITH 30" AND 36" BLADEGUARDS

2 ....... 37177 .................. FLANGE, INNER 6.0"

2 ....... 37176 .................. FLANGE ASSEMBLY, OUTER 6.0"

2 ....... 926790 ................ PIN, DOWEL

2 ....... 362007 ................ HOSE, WATER #6LP (30" BLADEGUARD)

2 ....... 362008 ................ HOSE, WATER #6LP (36" BLADEGUARD)

NOTICE

Part numbers on this Suggested Spare Parts List may supercede/replace the P/N's shown in the text pages of this manual.

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 7

NAMEPLATES AND DECALS

PAGE 8 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

NAMEPLATES AND DECALS

NO. PART NO. PART NAME QTY. REMARKS

1 37362 DECAL, STAY LEVEL HANDLE WHITE 2 2 20936 DECAL, MQ MULTIQUIP 5.93 X 7.45 2 3 37365 DECAL, MQ PS7060 2

4 SERIAL TAG ............................................................ 1 .................. CONTACT PARTS DEPT.

5 M600002 DECAL, DIESEL FUEL ONLY 1 6 25482 DECAL, MQ LOGO 3.0 X 3.75 1

7 37161 DECAL, HOT ISO HI-TEMPERATURE .................... 1 .................. SAFETY ITEM

8 13118 DECAL, POWDER COATED 1

9 20525 DECAL, WARNING "PROP 65" 3.25 X 4.25 ............ 1 .................. SAFETY ITEM

10 36092 DECAL, WARNING DIESEL FUEL 3.5 X 1.75 ......... 1 .................. SAFETY ITEM

11 36090 DECAL, WARNING VENTILATION 2 X 4 ................. 1 .................. SAFETY ITEM

12 11912 DECAL, PATENT PENDING 1 13 25282 DECAL, ATTENTION BATTERY DISCONNECTED 1

14 35137 DECAL, WARNING READ MANUAL ........................ 1 .................. SAFETY ITEM

15 36099 DECAL, PROTECTIVE CLOTHING ISO BLUE ........ 1 .................. SAFETY ITEM

16 37540 DECAL, HYDRAULIC RESERVOIR 1

17 21302 DECAL, WARNING KEEP GUARDS IN PLACE ...... 2 .................. SAFETY ITEM

18 22122-001 DECAL, WARNING RX-W ........................................ 2 .................. SAFETY ITEM

19 25249-001 DECAL, WARNING KEEP HANDS CLEAR ............. 2 .................. SAFETY ITEM

20 25250-001 DECAL, WARNING KEEP FEET CLEAR ................ 2 .................. SAFETY ITEM

21 25678 DECAL, BLADE ROTATION CCW ............................ 1 .................. SAFETY ITEM

22 23330-001 DECAL, CAUTION BELT DRIVE 2

23 606004 DECAL, GUARD REMOVAL ..................................... 2 .................. SAFETY ITEM

24 25491 DECAL, BLADE ROTATION CW 1 25 11092 DECAL, CE 1

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 9

INCH

100

125

150

175

200

230

255

280

305

330

355

380

WATERPUMP

OFF

WATER

OFF

BRAKES:

Thissaw is equipped with parking brakes. Brakesare applied automatically when engine isoff and dis-engaged when engine is running.

BEFORE STARTING:

WATER SUPPLY:

BLADES:

STARTING ENGINE:

STOPPING ENGINE:

FWD-

NEUTRAL-

REV CONTROL:

RAISE-

LOWER FUNCTION:

Checkall fluid levels. Secure blade firmly to bladeshaft.Make sure all protective guards arein place and properly mounted. Wear eye, earprotection and protective clothing.

Connectwater supply to water inlet. Move waterON/OFF CONTROL to ON position. AdjustWATER FLOW CONTROL lever to desiredposition. Drain watering system in coldweather to prevent damage due to freezing.

Alwaysfollow blade manufacturer's recommendationsfor blade selection, speedand application. NEVERexceed blade manufacturer's maximumrated RPM. See operator's manual fordetailed blade mounting instructions.

SetCONTROL HANDLE to NEUTRAL position. SetTHROTTLE to IDLE. Turn start switch to ONposition. Wait for glow plug indicator light togo out. Momentarily turn switch to start position;release switch as soon as engine starts.Allow engine to warm up for several minutesbefore increasing engine speed. Use approveddiesel fuel only.

Donot stop engine abruptly when hot! Reduce THROTTLEto IDLE and allow engine to run 1 to2 minutes before turning ignition switch off. Damageto engine may occur if not allowed to cooladequately.

Thepanel mounted handle controls FORWARD,NEUTRAL and REVERSE operation.Neutral position stops or holds saw ina stationary position. Incremental movementin the FORWARD or REVERSE directionwill increase speed proportionate toamount of movement.

RAISE-LOWERfunction is controlled by the switchmounted at the right side of the CONTROLHANDLE. Push toggle switch leverforward to lower saw. Pull toggle switch leverbackward to raise saw.

OPERATINGINSTRUCTIONS

FORWARD

NEUTRAL

REVERSE

WARNING

BLADESHAFTROTATIONDIS-ENGAGEMENT SYSTEM

Enginemust be at idle when engaging or dis-engagingbladeshaft drive.

Tostop bladeshaft rotation: Pushrocker switch labeled BLADESHAFT forward. Enginewill tilt forward, dis-engaging the belt drive.

Tostart bladeshaft rotation: Pushrocker switch labeled BLADESHAFT backward. Enginewill tilt back, engaging belt drive.

ENGINEMUST BE SHUT OFF

whenremoving or installing bladeor bladeguard or performing any type of service tobladeshaft or any other component on machine!

NEVER

attemptto remove or install blade or bladeguard

withengine running by dis-engaging the belt drive!

NEVER

attemptto service any component with the

enginerunning!

NEVER

leavesaw unattended while engine is running!

RAISE/LOWER

SWITCH

FWD-NEUTRAL-REV

CONTROL

NEVEREXCEED BLADE MANUFACTURER'S RECOMMENDED RPM'S

ADJUSTWATER FLOW VALVE FORDESIRED WATER FLOW

WATER

FLOW

CONTROL

TOADJUST CUT DEPTH INDICATOR: LOWERSAW UNTIL BLADE CONTACTS SURFACE,ADJUST DIAL TO ZERO.

DEPTH

INDICATOR

ToControl Depth of Cut with Saw Runningand Blade Mounted:

Step1:

Raisesaw above desired cutting depth.

Step2:

Turndepth control knob counterclockwise untilsaw cannot be lowered by pushing raise/lower switchforward. Step3:

Holdraise/lower switch in the lowering positionand rotate the depth control knob clockwise untildesired cutting depth is achieved. The saw will repeatto the same depth until re-adjusted.

ToRe-adjust for Full Cutting Depth:

Holdraise/lower switch in the lowering position and rotatethe depth control knob clockwise until saw is fullylowered. Rotate depth control knob clockwise additional1 turn.

DEPTH STOP CONTROL

CONTROL PANEL DECALS

ADJUSTWATER FLOW VALVE FORDESIRED WATER FLOW

ENGINE

Airfilter: Replace outer element when the SYSTEMS

airfilter restriction light comes on.STATUS

Replaceinner element every fourth outer element.

Oil: Check oil level daily, do not overfill.

SeeEngine Manual.

Oiltype: OilService: Change oil and filter every 125 hours

ofoperation. Changefuel filter every 250 hours of operation.

FuelFilter:

THROTTLE

TURNKNOB COUNTERCLOCKWISE.

TOINCREASE ENGINE SPEED:

TURNKNOB CLOCKWISE.

TOREDUCE ENGINE SPEED: FORQUICK THROTTLE ACTION: DEPRESS RED BUTTON AND

PUSHOR PULL KNOB.

DEPTH STOP CONTROL

ToControl Depth of Cut with Saw Runningand Blade Mounted:

Step1:

Raisesaw above desired cutting depth.

Step2:

Turndepth control knob counterclockwise untilsaw cannot be lowered by pushing raise/lower switchforward. Step3:

Holdraise/lower switch in the lowering positionand rotate the depth control knob clockwise untildesired cutting depth is achieved. The saw will repeatto the same depth until re-adjusted.

ToRe-adjust for Full Cutting Depth:

Holdraise/lower switch in the lowering position and rotatethe depth control knob clockwise until saw is fullylowered. Rotate depth control knob clockwise additional1 turn.

NEVEREXCEED BLADE MANUFACTURER'S RECOMMENDED RPM'S

HYDRAULICSYSTEM

OilLevel: Check reservoir daily. Fill reservoir to

FULLCOLD.

linemarked

Oiltype:

15W-40premium grade engine oil. Changeoil and filter every 500 hours of

OilService:

operationor annually, whichever occurs first.

Reservoir Reservoir is located inside console. Remove

rearpanel for access.

Location:

LIGHTS

AUXILIARY

OFF

TOADJUST CUT DEPTH INDICATOR: LOWERSAW UNTIL BLADE CONTACTS SURFACE,ADJUST DIAL TO ZERO.

BLADESHAFT DIS-ENGAGE

ENGAGE

MAINTENANCE INSTRUCTIONS

Note: Wheeldrive propulsion system, lift pump, andoil bath bladeshaft share common hydraulicoil reservoir, thus are maintained asa single system.

IGNITION SWITCH

START

ENGINE PRE-HEAT

OFF

BLADESHAFTROTATIONDIS-ENGAGEMENT SYSTEM

Enginemust be at idle when engaging or dis-engagingbladeshaft drive.

Tostop bladeshaft rotation: Pushrocker switch labeled BLADESHAFT forward. Enginewill tilt forward, dis-engaging the belt drive.

Tostart bladeshaft rotation: Pushrocker switch labeled BLADESHAFT backward. Enginewill tilt back, engaging belt drive.

ENGINEMUST BE SHUT OFF bladeor bladeguard or performing any type of service tobladeshaft or any other component on machine!

withengine running by dis-engaging the belt drive!

enginerunning!

attemptto remove or install blade or bladeguard

attemptto service any component with the

leavesaw unattended while engine is running!

whenremoving or installing

Service: Type:

Locations:

ENGINEPRE-HEAT GLOWPLUG

SYSTEMS STATUS

LUBRICATION

Greaseevery 125 hrs. of operation. Usepremium grade waterproof EP(extreme pressure) grease. Frontaxle pivot bearings (2), lift cylinderpins (2), engine tilt cylinder pin(1).

BLADE SPEED

BeltTension:

ToAdjust DriveBelt Tension:

DRIVEBELTS

Bladeshaftdrive belt tension is applied hydraulically when bladeshaftdrive is engaged.

Performfollowing procedure with saw fully lowered.

Loosenjam nut on belt tension limiting bolt. Turn belt tension limiting bolt counterclockwiseto create ½” minimum distance between end of bolt and frame. Startengine and engage belt drive; increase engine speed to full throttle position for 15seconds minimum. Slowengine speed to idle and shut engine off. Turn belt tensionlimiting bolt clockwise until bolt lightly contacts frame. Tighten locknut.

TACHOMETER

NEUTRAL-

RAISE-

OPERATINGINSTRUCTIONS

Checkall fluid levels. Secure blade firmly to bladeshaft.Make sure all protective guards arein place and properly mounted. Wear eye, earprotection and protective clothing.

Connectwater supply to water inlet. Move waterON/OFF CONTROL to ON position. AdjustWATER FLOW CONTROL lever to desiredposition. Drain watering system in coldweather to prevent damage due to freezing.

Donot stop engine abruptly when hot! Reduce THROTTLEto IDLE and allow engine to run 1 to2 minutes before turning ignition switch off. Damageto engine may occur if not allowed to cooladequately.

RAISE-LOWERfunction is controlled by the switchmounted at the right side of the CONTROLHANDLE. Push toggle switch leverforward to lower saw. Pull toggle switch leverbackward to raise saw.

Thissaw is equipped with parking brakes. Brakesare applied automatically when engine isoff and dis-engaged when engine is running.

ENGINEWILL NOT CRANK ORSTART WHEN E-STOP BUTTONIS DEPRESSED

WATERPUMP

PAGE 10 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

CONTROL PANEL DECALS

NO. PART NO. PART NAME QTY. REMARKS

1 37361 DECAL, MAINTENANCE, 7000 SERIES 1 2 37354 DECAL, INSTRUMENT PANEL, 7000 SERIES 1 3 37353 DECAL, OPERATION CONSOLE PANEL 1

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 11

ELECTRICAL CONTROL ASSY.

PAGE 12 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

ELECTRICAL CONTROL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 406000 SWITCH, ROCKER CH# M-58031-01 2

2 406017 IGNITION SWITCH, WITH KEYS ............................ 1................... INCLUDES ITEMS W/

3 37198 EMERGENCY STOP SWITCH ................................ 1 .................. SAFETY ITEM

4 37094 SWITCH, TOGGLE SPDT MOMENTARY ON-ON 1 5 37203 SWITCH, SNAP ACTION ROLLER PLUNGER 1 6 37490 HARNESS, RELAYS AND CIRCUIT BREAKERS 1 7 406021 INDICATOR, ENGINE 1 8 37243 SWITCH, ROLLER ARM 1 9 933240 WASHER, FLAT SAE 1/4 GRD 9 YZ 3 10 405000 CONNECTOR, 4-WAY SOCKET 1 11 37368 TACHOMETER, ELECTRIC 0-3000 RPM 1 12 8381 BOOT, TOGGLE SWITCH 1 13 406020 BLANK, ROCKER SWITCH 2 14 973752 SCREW, BHHC 1/4 - 20 X 5/8 SS 3 15 37325 SCREW, SHC M5 - 0.8 X 30MM 2 16 37324 NUT, NYLOC M5 - 0.8 2 17 28922-058 WASHER, M5 2 18 19 25628 SOLENOID, LIFT PUMP 1

406017-1 KEY, IGNITION 1

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 13

CONSOLE MOUNTS ASSY.

PAGE 14 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

CONSOLE MOUNTS ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 20742 ISOLATOR, RB2 RING/BUSHING 4 2 20743 WASHER, ISO SNUB KROFUND DYN 148099-18 4 3 575001 RUBBER ISOLATOR, TPC# 60166-1 4 4 37231-753 MOUNT, ISOLATOR FRONT 2 5 37233-753 MOUNT, ISOLATOR SIDE 2 6 37227-753 MOUNT, CONSOLE ISOLATOR FRONT 2 7 12832 WASHER, SNUBBING 4 8 06503-026 SCREW, HHC 1/2 - 13 X 3-1/4 4 9 1665 SCREW, HHC 3/8 - 16 X 2 4 10 37116-753 CONSOLE W/A 1 11 933242 WASHER, FLAT SAE 3/9 GRD 9 Y 8 12 0205 SCREW, HHC 3/8-16 X 1 8 13 TBD SCREW 4 14 TBD WASHER 4

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 15

REAR CONSOLE ACCESS PANEL ASSY.

PAGE 16 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

REAR CONSOLE ACCESS PANEL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

5 37219 STRIP, BACKING PLATE SAW CONSOLE 1 6 37220 STRIP, VERTICAL SAW CONSOLE 2 7

9 37253 PANEL ASSEMBLY, REAR SAW ACCESS ............. 1 .................. INCLUDES ITEMS W/

10024 NUT, NYLOC 1/4 X 20 4 10930 WASHER, FENDER 1/4 X 1-1/4 4 12287 SCREW, THP 1/4 - 20 X 3/4 SS 4 29057 DOCUMENT BOX 1

37254-753 PANEL, REAR SAW ACCESS 1 560020 LATCH, REAR SAW ACCESS PANEL 2

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 17

LIGHT CONNECTOR/DASH ACCESS ASSY.

PAGE 18 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

LIGHT CONNECTOR/DASH ACCESS ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 0655 SCREW, HHC 5/16 - 18 X 3/4 8 2

5 13287 NUT, NYLOC 8-32 2

6 25865 HARNESS, LIGHT KIT ............................................ 1 .................. INCLUDES ITEMS W/

7 37234-753 COVER W/A, CONSOLE DASH ACCESS 1 8 923114 SCREW, SHC 8-32 X 1/2 2 9 933241 WASHER, FLAT SAE 5/16 GRD 9YZ 8 10

11+# 0161 C WASHER, LOCK 5/16 MED 2 12+# 0161 D NUT, HEX 5/16 - 18 2 13+# 0300 A SCREW, HHC 5/16 - 18 X 2 1

14+ 2532 LIGHT ASSEMBLY .................................................. 1 .................. INCLUDES ITEMS W/#

15+ 15503 KNOB, COMFORT GRIP STAR 1 16+ 120206 LIGHT BAR 1 17+ 405001 CONNECTOR PLUG, 4-PIN FEMALE 1 18+ 405002 CORD, LIGHT EXTENDABLE 1 19+# H9406 BULB, GE H9406 1

20 M18004 LIGHT KIT, SAW ...................................................... 1 .................. INCLUDES ITEMS W/+

21# 11963 BOLT, CARRIAGE 5/16 - 18 X 1 1

12171 SEAL, WEATHERPACK 16-18 GA,GREEN 2 12176 CONNECTOR, WEATHERPACK 2 PIN MALE 1 12179 TERMINAL, WEATHERPACK MALE 14-16 GA 2

405000 CONNECTOR, 4-WAY SOCKET CHROME 1

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 19

BELT AND ENGINE GUARDS ASSY.

PAGE 20 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

BELT AND ENGINE GUARDS ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 0166 SCREW, HHC 3/8 - 16 X 7/8 5 3 15503 KNOB, COMFORT 1

4 37202-753 GUARD, BELT DRIVE .............................................. 1 .................. SAFETY ITEM

5 37209-753 GUARD, ENGINE ..................................................... 1 .................. SAFETY ITEM

8 584011 WRENCH, 15/16 BLADE CLOSED END 1 9 933242 WASHER, FLAT SAE 3/8 GRD 9 YZ 5

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 21

DEPTH INDICATOR/STOP SWITCH ASSY. (OLD STYLE)

PAGE 22 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

DEPTH INDICATOR/STOP SWITCH ASSY. (OLD STYLE)

NO. PART NO. PART NAME QTY. REMARKS

1 10024 NUT, NYLOC 1/4 - 20 2 2 37155 PULLEY, CABLE .75 OD 1 3 37235 BASE, SAW DEPTH INDICATOR 1 4 37240 PULLEY, CABLE .75 OD 2 5 37241 SHAFT, DEPTH INDICATOR 1 6 37332 RING, 3/16 E-STYLE EXTERNAL 2 7 37401 SCREW, SH SHLDR 1/2-20, 5/16 OD X 1/4 L 1 8 37504 CABLE, NYLON COAT SS .049 1 9 110031 POINTER, CONCRETE SAW DEPTH 1 10 460019 FLANGE, BEARING 0.25 ID X 0.75 OD 1 11 560025 KNOB, SAW DEPTH INDICATOR 1 12 565005 SPRING, EXTENSION 1 13 583059 SHIM, 0.375 OD X 0.25 ID X .020 THK 5 14 584025 STUD, 1/4 - 20 X 1-3/4 NO PLT 1 15 933240 WASHER, FLAT SAE 1/4 GRD 9 YZ 1 16 973752 SCREW, BHSC 1/4 - 20 X 5/8 SS 2 17 37248 MOUNT, SWITCH PIVOT PLATE 1 18 37246 NUT, SWIVEL DEPTH STOP 1 19 37247 KNOB, DEPTH STOP CONTROL 1 20 37249 COLLAR, SHAFT THREADED 3/8 - 16 1 21 37250 WASHER, BELLEVIEW .317 X .625 2 22 19470 WASHER, FLAT 5/16 USS 2 23 933242 WASHER, FLAT SAE 3/8 GRD 9 YZ 1 24 5283 NUT, NYLOC 5/16 - 18 2 25 10133 NUT, NYLOC 3/8 - 16 1 26 37251 WASHER, BELLEVIEW .389 X .750 2 27 37375 STUD, 3/8 - 16 X 4 1 28 4001 WASHER, FLAT USS 3/8 PLD 3

NOTICE

Parts on this page are no longer available. See Depth Indicator/Stop Switch Assy. (New Style).

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 23

DEPTH INDICATOR/STOP SWITCH ASSY. (NEW STYLE)

PAGE 24 — PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10)

DEPTH INDICATOR/STOP SWITCH ASSY. (NEW STYLE)

NO. PART NO. PART NAME QTY. REMARKS

1 37544 SHAFT, DEPTH INDICATOR 1 2 37545 BUSHING, FLANGED 2 3 37547 SHAFT, IDLER PULLEY 2 4 37548 PULLEY, IDLER 2 5 110031 POINTER, CONCRETE SAW DEPTH 1 6 560025 KNOB, SAW DEPTH INDICATOR 1 7 37549 PULLEY, DUAL GROOVE 1 8 37550 BELT, INDICATOR DRIVE 1 9 0948 WASHER, FLAT SAE 1/4 3 10 37332 RING, 3/16 E-STYLE EXTERNAL 6 11 926149 SCREW, SHDLR 1/4D X 5/16L, 10-24 SCKT HD 1 12 37162 SPRING, EXTENSION 1 13 973752 SCREW, BHSC 1/4 - 20 X 5/8 SS 2 14 37551 HOUSING, DEPTH INDICATOR 1 15 37557 BRACKET, CABLE INDICATOR 1 16 2295 SCREW, HHC 1/4 - 20 X 7/8 1 17 10024 NUT, NYLOC 1/4 - 20 2 18 37401 SCREW, SH SHLDR 1/2-20, 5/16 OD X 1/4 L 1 19 37679 RING, SNAP SH 87 2 20 37678 CABLE ASSY., DEPTH INDICATOR 1

NOTICE

Parts on this page replace those listed on Depth Indicator/Stop Switch Assy. (Old Style).

PS7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #8 (07/26/10) — PAGE 25

+ 57 hidden pages