Multiquip MVC88VGH-VGHW User Manual
OPERATION AND PARTS MANUAL
SERIES
MODEL MVC-88VGH/VGHW
ONE-WAY PLATE COMPACTOR
(HONDA GASOLINE ENGINE)
Revision #2 (08/06/10)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
MVC-88VGH/VGHW PLATE COMPACTOR — PROPOSITION 65 WARNING
l
PAGE 2 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
NOTES
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 3
MVC-88VGH/VGHW PLATE COMPACTOR — TABLE OF CONTENTS
Multiquip —MVC88VGH/VGHW
Plate Compactor
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Information ................................................ 6-10
Specifications (Compactor/Engine) ........................ 11
General Information ................................................ 12
Components (Plate Compactor) ............................. 13
Components (Engine) ............................................. 14
Inspection ........................................................... 15-16
Initial Start-Up .................................................... 17-18
Operation ................................................................ 18
Maintenance ...................................................... 19-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine) ................................... 23-24
Troubleshooting (Plate Compactor) ........................ 24
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Honda GX160U1QMX2 Engine
Cylinder Head Assembly ....................................38-39
Cylinder Barrel (Recoil) Assembly ..................... 40-41
Crankcase Cover Assembly ............................... 42-43
Crankshaft Assembly .........................................44-45
Piston/Rings Assembly.......................................46-47
Camshaft Assembly ...........................................48-49
Recoil Starter .....................................................50-51
Fan Cover Assembly .......................................... 52-53
Carburetor Assembly ......................................... 54-55
Air Cleaner Assembly ......................................... 56-57
Muffler Assembly ...............................................58-59
Fuel Tank Assembly ........................................... 60-61
Cooling Fan & Flywheel Assembly ..................... 62-63
Ignition Coil Assembly ........................................ 64-65
Control Assembly ............................................... 66-67
Terms and Conditions Of Sale — Parts .................. 68
Component Drawings
Nameplate and Decals....................................... 28-29
Body Assembly .................................................. 30-31
Vibrator Assembly .............................................. 32-33
Sprinkler Assembly (Option) .............................. 34-35
Transport Wheel Assembly (Option) .................. 36-37
l
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
January 1
Effective:
st
, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
N View Parts Diagrams
N Order Parts
N Print Specification Information
Goto www.multiquip.com and click on
Order Par ts
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
to log in and save!
Order via Phone:
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
R Dealer Account Number
R Dealer Name and Address
R Shipping Address (if different than billing address)
R Return Fax Number
R Applicable Model Number
R Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
R Specify Preferred Method of Shipment:
UPS/Fed Ex DHL
N Priority One Tr uck
N Ground
N Next Day
N Second/Third Day
www.multiquip.com
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 5
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others. The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
l
PAGE 6 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
NEVER operate this equipment under the influence of
drugs or alcohol.
ALWAYS check the equipment for loosened threads or
bolts before starting.
DO NOT use the equipment for any purpose other than
its intended purposes or applications.
NOTICE
This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
ALWAYS know the location of the nearest
fire extinguisher.
ALWAYS know the location of the nearest
first aid kit.
ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance, doctor and fire department.
This information will be invaluable in the case of an
emergency.
ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 7
MVC-88VGH/VGHW PLATE COMPACTOR —
r
SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
NEVER operate the equipment in an explosive
atmosphere or near combustible materials. An
explosion or fire could result causing severe
bodily harm or even death.
WARNING
NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death. Disconnection of any of these
devices will void all warranties.
CAUTION
NEVER lubricate components or attempt service on a
running machine.
NOTICE
ALWAYS keep the machine in proper running condition.
Fix damage to machine and replace any broken parts
immediately.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
ENGINE SAFETY
DANGER
The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
cause death if inhaled.
The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
l
WARNING
DO NOT place hands or fingers inside engine
compartment when engine is running.
NEVER operate the engine with heat shields or
guards removed.
Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
CAUTION
NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to cool
before servicing equipment.
NOTICE
NEVER run engine without an air filter or with a dirty air
filter. Severe engine damage may occur. Service air filte
frequently to prevent engine malfunction.
NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
PAGE 8 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
FUEL SAFETY
DANGER
DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
FUEL
FUEL
DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
ALWAYS use extreme caution when working with
flammable liquids.
DO NOT fill the fuel tank while the engine is running
or hot.
DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
DO NOT drop the battery. There is a possibility that the
battery will explode.
DO NOT expose the battery to open flames,
sparks, cigarettes, etc. The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
WARNING
ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
Use well-insulated gloves when picking up
the battery.
ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
ALWAYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gases.
If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
NEVER use fuel as a cleaning agent.
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 9
CAUTION
ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
ALWAYS shutdown engine before transporting.
NEVER lift the equipment while the engine is running.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
Use adequate lifting cable (wire or rope) of sufficient
strength.
Use one point suspension hook and lift straight
upwards.
DO NOT lift machine to unnecessary heights.
ALWAYS tie down equipment during transport by
securing the equipment with rope.
ENVIRONMENTAL SAFETY
NOTICE
Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
l
PAGE 10 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — SPECIFICATIONS
)rotcapmoC(snoitacificepS.1ELBAT
sledoMWHGV88-CVM/HGV88-CVM
ecroFlagufirtneC)gk9.465,1(.sbl054,3
VforebmuNnim/snoitarbiv008,5
snoitarbi
deepSgnilevarT)nim/sretem71(nim/.tf65
)WxL(eziSetalP
)
HGV(thgieWgnitarepO
)WHGV(thgieWgnitarepO
yticapaCknaTleuF)sretil6.3(.tq
yticapaCknaTretaW
ylnOledoMWHGV
noitcapmoCfOaerA.xaM.rh/.tf.qs0085
ledoM2XMQ1U061XGADNOH
epyT
.ni7.02x7.91
mm525.x005.
).gk0.98(.sbl691
).gk5.89(.sbl712
8.3
)sretil0.31(.tq7.31
)enignE(snoitacificepS.2elbaT
elgniS,ekorts4delooc-riA
latnoziroH,VHO,rednilyC
enignEenilosaGtfahS
ekort
SXeroB
tnemecalpsiD)ni-uc9.9(cc361
tuptuOxaM.M.P.R0063/.P.H5.5
enignE
yticapaCknaTleuF
leuF
yticapaCliOebuL)stq36.0(sretil06.
tnoCdeepS
thgieWteNyrD
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 11
dohteMlor
dohteMgnitratStratSlioceR
.ni8.1x.ni7.2
)mm54xmm86(
llag.S.U59.0.xorppA
sno
)sretil6.3(
elibomotuAdedaelnU
enilosaG
thgiew-ylFlagufirtneC
epyT
).gK51(sbl33
MVC-88VGH/VGHW PLATE COMPACTOR — GENERAL INFORMATION
Definition of Plate Compactor
The Mikasa MVC-88VGH/VGHW is a walk behind, plate
compactor designed for the compaction of sand, mixed soils
and asphalt. This plate compactor is a powerful compacting tool
capable of applying a tremendous force in consecutive high
frequency vibrations to a soil surface. Its applications include
compacting for road, embankments and reservoirs as well as
backfilling for gas pipelines, water pipelines and cable installation
work.
Vibratory Plates
The vibratory plates of the MVC-88GH/GHW produce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
The resulting vibrations cause forward motion. The engine and
handle are vibration isolated from the vibrating plate.
Frequency/Speed
The compactor's vibrating plate has a frequency range between
5800 vpm (vibrations per minute). The travel speed of the
compactor is approximately 17 meters/minute (56 ft./minute).
Engine
The Mikasa MVC-88VGH/VGHW Plate Compactor is equipped
with a Honda GX160U1QMX2 air cooled, 4-cycle gasoline
engine. The engine drives an eccentric weight at a high speed
to develop a compaction force. In addition this engine is equipped
with an
Oil Alert
before the engine falls below safe engine oil operating limits.
Always be sure to check the engine oil level prior to starting
the engine.
Controls
Before starting the MVC-88VGH/VGHW Plate Compactor identify
and understand the function of the controls and components.
system that will automatically stop the engine
l
PAGE 12 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — COMPONENTS (COMPACTOR)
Figure 1. Plate Compactor Controls
Figure 1 shows the location of the basic controls and components
of the MVC-88VGH/VGHW Plate Compactor. The function of
each control is described below:
1. Water Tank Cap (VGHW Only) – Remove this cap to add
water to the water tank.
2. Fuel Tank Cap – Remove this cap to add fuel.
3. Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
4. Handle Bar – When operating the compactor use this
handle bar to manuever the compactor.
5. Gasoline Engine – This plate compactor uses a HONDA
GX160U1QMX2 engine. Refer to the HONDA owner's
manual for engine information and related topics.
6. Belt Cover – Remove this cover to gain acess to the V-belts.
NEVER run the compactor without the V-belt cover. If the Vbelt cover is not installed, the possibility exists that your
hand may get caught between the V-belt and clutch, causing
serious injury and bodily harm.
7. Vibrating Plate – A flat, open plate made of durable cast
iron construction used in the compacting of soil.
8. Vibration Case – Encloses the eccentric, gears and
counter weights.
9. Water Tube (Sprinkler) – Supplies water to the soil via a
splash plate.
10. Water Shut-Off Valve – Turn this valve downward to let
water flow from the water tank to the water tube.
11. Water Tank (VGHW only) – Holds 13.7 quarts of water
(removable, no tools required).
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 13
MVC-88VGH/VGHW PLATE COMPACTOR — COMPONENTS ( ENGINE)
Figure 2. Engine Controls & Components
ENGINE COMPONENTS
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
DANGERDANGER
DANGER
DANGERDANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity
to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward -
FAST
).
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
SLOW
Explosive
Fuel Hazard
l
, lever back toward operator -
5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
NOTE
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9. Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
WARNINGWARNING
WARNING
WARNINGWARNING
Operating the engine without an air
filter, with a damaged air filter, or a filter
in need of replacement will allow dirt
to enter the engine, causing rapid
engine wear.
Burn Hazard
PAGE 14 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — INSPECTION
Before Starting
1. Read safety instructions at the
beginning of manual.
2. Clean the compactor, removing
dirt and dust, particularly the
engine cooling air inlet, carburetor
and air cleaner.
3. Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with dry
compressed air.
5. Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
Engine Oil Check
1. To check the engine oil level, place the pump on secure
level ground with the engine stopped.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 3) and wipe clean.
NOTE
Adding fuel to the fuel tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until the
fuel residue has been completely wiped up, and the area
surrounding the engine is dry. DO NOT attempt to refuel the
compactor if the engine is
The Oil Alert System will automatically
stop the engine before the engine falls
below safe limits. Always be sure to
check the engine oil level prior to
starting the engine.
epyTliO.3elbaT
nosaeS erutarepmeT epyTliO
remmuS rehgiHroC°52 03-W01EAS
llaF/gnirpS C°01~C°52 02/03-W01EAS
retniW rewoLroC°0 01-W01EAS
DANGERDANGER
DANGER
DANGERDANGER
Explosive
Fuel Hazard
hot! or running
.
Fuel Check
Figure 3. Engine Oil Dipstick (Removal)
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 4), fill to the edge of the oil filler
hole with the recommended oil type (Table 3). Maximum oil
capacity is 0.63 quarts (0.60 liters)
Figure 4. Engine Oil Dipstick (Oil Level)
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 15
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel
immediately!
MVC-88VGH/VGHW— INSPECTION
V-Belt Check
CAUTICAUTI
CAUTION
CAUTICAUTI
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur of your hand (Figure 5) gets caught
between the V-belt and the clutch. Always use safety gloves.
CLUTCH
PULLEY
VIBRATOR
PULLEY
Figure 5. V-Belt Hazard
2. The V-belt tension is proper if the V-belt bends 10 to 15 mm
3. A loose V-belt will decrease the power transmission output,
4. If the V-belt becomes worn or loose, replace it.
(Figure 7) when depressed with finger at midway between
the clutch and vibration pulley shafts.
Figure 7. V-Belt Tension
causing reduced compaction and premature wear of the
belt.
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 6.
l
Vibrator Oil Check
1. Place the MVC-88VGH/VGHW plate compactor horizontally
on a flat surface. Make sure the compactor is level when
checking the oil in the vibrator assembly.
2. Check vibrator oil level by removing the plug (vibrator oil gauge)
as shown in Figure 8. The oil level should be up to the oil plug.
The vibrator holds 140 cc (approximately 4 ounces).
IMPORTANT, if oil is required, replace using only SAE10W-30
motor oil.
Figure 8. Vibrator Oil Plug
Figure 6. V-Belt Cover Removal
PAGE 16 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— INITIAL START-UP
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT attempt to run the compactor until
the Safety and Initial Start-upsectionshave
been read and understood.
1. Place the
2. Place the
position.
fuel valve lever
Figure 9. Fuel Valve Lever
Engine ON/OFF switch
(Figure 9) in the "ON" position.
D
(Figure 10) in the "ON"
NOTE
4. Place the
and
throttle lever
slow
.
The CLOSED position of the
choke lever enriches the fuel
mixture for starting a COLD
engine. The OPEN position
provides the correct fuel
mixture for normal operation
after starting, and for restarting
a warm engine.
(Figure 12) halfway between
fast
Figure 10. Engine ON/Off Switch
3. Place the
Choke Lever
(Figure 11) in the "OPEN" position.
Nnnn
Figure 12. Throttle Lever
5. Grasp the starter grip (Figure 13) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding the compression point. Rewind the rope a little from
that point and pull out sharply.
CAUTICAUTI
CAUTION
CAUTICAUTI
DO NOT pull the starter rope all the way to the end
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
D
Figure 11. Choke Lever
Figure 13. Starter Grip
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 17
MVC-88VGH/VGHW— INITIAL START-UP/OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the
started repeat steps 1 through 5.
7. Before the compactor is put into operation run the engine for
3-5 minutes.
8. Check for abnormal engine noises or fuel leaks.
Operation
CAUTICAUTI
CAUTION
CAUTICAUTI
Make sure to follow all safety rules referenced in the safety
section of this manual before operating compactor. Keep work
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
1. Once the engine has started, move the engine throttle lever
quickly to the
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the centrifugal clutch.
CLOSED
fast
position.
position. If the engine has not
Stopping the Engine
NEVER stop the engine suddenly while working at high
speeds.
1. Place the
listen for the engine speed to decrease.
2. Place the
" position.
3. Place the
CAUTICAUTI
CAUTION
CAUTICAUTI
throttle lever
Engine ON/OFF switch
fuel valve lever
(Figure 12) in
(Figure 9) in the "OFF" position.
D
slow
position, and
(Figure 10) in the "
OFF
ALWAYS
NOTE
5. Firmly gasp the compactor's handle bar with both hands , the
compactor will begin moving forward.
6. Slowly walk behind the compactor and be on the lookout for
any large objects or foreign matter that might cause damage
to the compactor or bodily injury.
7. Compactor traveling speed may drop on soils which contain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil. To
rectify this problem do the following:
■
Check the bottom plate to see if clay or equivalent material
has been lodge in the plate mechanism. If so, wash with
water and remove.
■
Remember the compactor does not work as efficiently on
clay or soils that have a high moisture content level.
quickly without hesitation,
because increasing the engine
speed slowly causes the clutch
to slip.
move the throttle lever
l
■
If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
PAGE 18 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— MAINTENANCE
CAUTICAUTI
CAUTION
CAUTICAUTI
Inspection and other services should
always
be carried out
on hard and level ground with the engine shutdown.
Inspection and Maintenance Service Tables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 4 through 6.
TSRIF
)3(NOITPIRCSEDNOITAREPOEROFEB
KCEHCX
liOenignE
EGNAHCX
RO
CAUTICAUTI
CAUTION
CAUTICAUTI
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
CAUTICAUTI
CAUTION
CAUTICAUTI
Fuel piping and connections should be replaced every 2
years.
eludehcSecnanetniaMenignE.4elbaT
YREVE
HTNOM
.SRH01
SHTNOM3
RO
.SRH52
YREVE
SHTNOM6
RO
.SRH05
YREVE
RAEY
RO
.SRH0
01
YREVE
SRAEY2
RO
.SRH002
KCEHCX
renaelCriA
EGNAHC)1(X
stloB&stuNllA
gulPkrapS
sniFgnilooCKCEHCX
retserrAkrapSNAELC X
knaTleuFNAELC X
retliFleuFKCEHC X
deepSeldITSUJ
ecnaraelCevlaVTSUJDA-KCEHC )2(X
senilleuFKCEHC )2()yrassecenfiecalper(sraey2yrevE
neuqerferomecivreS)1( YTSUD .saera
fInethgit-eR
yrasseceN
NAELC-KCEHCX
ECALPER X
DA-KCEHC )2(X
vresebdluohssmetiesehT)2(
X
nidesunehwylt
yllacinahcemeradnaslootreporpehtevahuoysselnu,relaedecivresruoyybdeci
.serudecorpecivresroflaunaMpohSADNOHehtotrefeR.tneiciforp
amreporpenimretedotnoitarepofosruohgol,esulaicremmocroF)3(
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 19
.slavretniecnanetni
MVC-88VGH/VGHW — MAINTENANCE
metI noitarepOfosruoH skrameR
)kcehcgnitratS(
tsolrodenesooL
swercs
trapynafoegamaD
trapmetsys
kcehcliorotarbiV sruoh001yrevE .91egapeeS
liorotarbiV
tnemecalper
kcehc)hctulc(tleb-V ruoh002yrevE .91egapeeS
)yad
)yad
)yad
gnillortnocfonoitcnuF
)yad
Daily Service
■
Check for leakage of fuel or oil.
■
Check engine oil.
yreve(sruoh8yrevE
yreve(sruoh8yrevE
yreve(sruoh8yrevE
yreve(sruoh8yrevE
sruoh002yrevE .91egapeeS
NOITCEPSNIENIHCAM.5ELBAT
ENGINE OIL
1. Drain the engine oil when the oil is
warm
as shown in
Figure 14.
2. Remove the dipstick and then unscrew the oil plug and
allow the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten securely.
■
Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening.
.6ELBAT
mm6 mm8 mm01 mm21 mm41 mm61 mm81 mm02
lairetaM
T4 07 051 003 005 057 001,1 004,1 000,2
T8-6 001 052 005 008 003,1 000,2 007,2 008,3
T11 051 004 008 002,1 000,2 009,2 002,4 006,5
* )mm01(007~056)mm8(053~003)mm6(001
l
)munimulafositrap-retnuocesacnI(*
.wercsdna
Figure 14. Engine Oil (Draining)
ENGINE AIR CLEANER
retemaiD)mc/gk.ni(EUQROTGNINETHGIT
1. Remove the air cleaner cover and foam filter element as
shown in Figure 15.
2. Tap the paper filter element (Figure 15) several times on a
hard surface to remove dirt, or blow compressed air [not
2
exceeding 30 psi (207 kPa, 2.1 kgf/cm
element from the air cleaner case side.
)] through the filter
NEVER
brush off dirt.
Brushing will force dirt into the fibers. Replace the paper filter
element if it is excessively dirty.
)dednahthgirllaeraenihcamsihthtiwesunisdaerhT(
,tlobhcaenodekramsilairetamfoytilauqdnalairetaM
3. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engine oil and completely squeeze out the excess oil from the
element before installing.
PAGE 20 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— MAINTENANCE
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check the V-belt tension. Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
CAUTICAUTI
CAUTION
CAUTICAUTI
Whenever the compactor's vibration becomes weak or lost
during normal operation regardless of operation hours, check
the V-belt and clutch immediately.
■
Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway of V-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that the V-belt will come off.
Figure 15. Air Cleaner
CHANGING VIBRATOR OIL
1. When changing the vibrator oil, remove the drain plug
located at the bottom- right of the vibrator (Figure 5), and
simply tip the compactor to drain the oil. Note that the oil will
drain more easily while it is hot. Remember to use only
10W-30 motor oil when replacing vibrator oil.
CAUTICAUTI
CAUTION
CAUTICAUTI
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand (Figure 6) gets caught
between the V-belt and the clutch. Always use safety gloves.
■
Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
■
Checking Clutch
Check the clutch simultaneously with V-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 21
Loading...