Multiplex PARKMASTER 3D User guide

Operating Instructions for Power Set „PARKMASTER 3D“

owe

599

02/

) o

cep

! These operating instructions are an integral part of the

product. They contain important information and safety notes, and should be kept in a safe place at all times. Be sure to pass them on to the new owner if you ever dis pose of the product.

5. ASSEMBLING OF THE

POWER SET “PARKMASTER 3D”

1. INTRODUCTION

Perfectly matched components form the basis of this high-performance power set “PARKMASTER 3D” # 33 2638 for 3-D park-fly models such as our PARKMASTER 3D and comparable model aircraft with all-up weights of up to around 600 g.

2. CONTENTS / REPLACEMENT PARTS

• 1 Himax C 2816-0890 motor # 33 3016

• 1 MULTIcont BL-17/II speed controller # 7 2280

• 1 11” x 5.5” propeller # 73 3179

• 1 propeller driver with spinner for moto r shafts ∅ 4 mm,

prop-shaft 6 mm # 33 2314

• various small items for installation in the model

3. TYP. OPERATIONAL DATA OF POWER SET “PARKMASTER 3D”

3S LiPo / 11” x 5,5” prop Current drain: approx.17.0 A

Recommended Battery:

MULTIPLEX Li-BATT BX 3/950 # 15 7116

LTIPLEX

If you use the Himax C 2816-0890 motor and the stan-

dard propeller supplied in the set, do not use more than a

3S LiPo pack or 9 NiXX cells

t x

4. SAFETY NOTES

n i

The power set “PARKMASTER 3D” is designed exclu-

sively for use in modelling applications. Incorrect use can

result in serious personal injury.

• Read the instructions before initiation

Err

• Before every flight, check that the motor and propeller are securely mounted

DAMA

• Remove all movable objects from the area around the

propeller before switching the motor on

• Do not allow clothing or any of your extremities to get close to the spinning propeller

• Never start running the motor in your hand

• Stop the motor immediately if you notice vibration.

D”

Eliminate the cause of the vibration before running it again; you may need to correct the balance of the pro-

TER

peller

• Make sure the power system is adequately cooled; do

not allow anything to obstruct the free circulation of air

t “PARKMA r

1. Screw the motor to the motor mount Æ ensure that the motor is free to rotate. When deploying the motor cables, check that they cannot make contact with the spinning motor. Secure the motor leads with Velcro tape or similar.

2. Fit the propeller driver and clamping ring on the motor shaft.

3. Look at the propeller from the front (the face stating the propeller size), and check whether the hole is bored centrally, i.e. whether it lines up correctly with the moulded-in guide hole on the underside. If this is not the case, adjust the propeller bore so that the front hole lines up with the rear one. CAUTION: don’t adjust or drill out the rear guide hole.

4. Locate the retainer ring supplied in the set, and place it in the rear guide hole. Fit the propeller on the driver, and secure it with the spinner.

6. INITIATION OF THE POWER SET

“PARKMASTER 3D”

1. Connect the three wires attached to the speed control-

ler to the three wires attached to the motor; the order of connection is unimportant.

2. Locate the UNI connector attached to the speed con-

troller, and connect it to your receiver.

3. Switch the transmitter on, and check that the throttle

control is at the “OFF” position.

4. Connect the flight battery to the speed controller.

5. Check the direction of rotation of the motor: it should spin clockwise when viewed from the tail, looking forward. If this is not the case, disconnect the flight battery and swap over any two of the three motor wires.

6. Switch off the motor brake at the speed controller; the

method of doing this is described in the instructions supplied with the controller.

r P f

n ti

tr In tin

MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 1/2

Operating Instructions for Power Set „PARKMASTER 3D“

owe

599

02/

) o

cep

7. HIMAX MOTOR - SPECIFICATION

Type: C 2816-0890

# 33 3016

RPM / V: 0890

Cell count, NiXX / LiPo: 6 - 12 / 2S - 4S

Efficient operating current: 4 A - 13 A

Max. current for 15 sec.: 18 A

Shaft Ø:

4.0 mm

Diameter: 28 mm

Length: 33 mm Weight: 77 g

Max. output: 200 W

Max. case temperature:

Mounting: 16 mm Ø / 4 x M2.5

65° C

You will find comprehensive operating instructions for the Himax C 2816-0890 at www.multiplex-rc.de Æ DOWNLOADS Æ INSTRUCTIONS.

8. GUARANTEE

MULTIPLEX products are covered by the statutory guarantee regulations. If you wish to make a claim under guarantee, please contact the model shop where you purchased the product in the first instance.

The guarantee does not cover damage and malfunctions caused by:

LTIPLEX M

• Improper handling, incorrect connections,

reversed polarity

• Use of accessories other than genuine MULTIPLEX

items

• Modifications or repairs not carried out by MULTIPLEX

or an authorised MULTIPLEX Service Centre

• Accidental or deliberate damage

• Defects due to normal wear and tear

• Use outside the technical specifications

Err

9. CE APPROVAL

This product satisfies all the relevant statutory harmonised EU directives.

You are therefore the owner of a product whose design fulfils the protective aims of the European Community relating to the safe operation of equipment.

You are entitled to obtain a copy of the conformity declaration for this product by contacting MULTIPLEX using the information at the foot of the page.

10. DISPOSAL INFORMATION

Electrical equipment marked with the cancelled waste bin symbol must not be discarded in the standard household waste; instead it must be taken to a suitable specialist disposal system.

In the countries of the EU (European Union), electrical equipment must not be discarded via the normal domestic refuse system (WEEE – Waste of Electrical and Electronic Equipment, directive 2002/96/EG). You can take unwanted equipment to your nearest local authority waste collection point or recycling centre, where the items will be disposed of correctly and at no cost to you.

By returning your unwanted equipment you can make an important contribution to the protection of the environment.

DAMA 4-

D”

TER

t “PARKMA r

r P f

n ti

tr In tin

MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 2/2