Multiplex MENTOR User guide
Operating Instructions for Power Set ”MENTOR”
! These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dis pose
of the product.
1. INTRODUCTION
Obtain the maximum performance, with the Power Set
“MENTOR” # 33 2641, from your trainer and even use it
for glider-towing. Suitable for trainers with a maximum allup weight of about 2200 g.
2. CONTENTS / REPLACEMENT PARTS
• 1 Himax C 3528-1000 motor # 33 3028
• 1 MULTIcont BL-54 speed co ntroller # 7 2277
• 1 11” x 5.5” propeller # 73 3179
• 1 propeller driver and nut for ELAPOR spinner
Motor shaft-Ø 5mm, Prop-shaft 6 mm # 33 2326
• Various small items for installation in the model
Options for use in Magister:
• GRP motor mount for Magister # 33 2671
• ELAPOR-spinner Ø 62 mm # 22 4207
3. TYP. OPERATIONAL DATA OF POWER SET
“MENTOR”
3S LiPo / 11” x 5,5” prop Current drain: approx. 36.0 A
Recommended flight battery:
MULTIPLEX Li-BATT BX 3/3200 # 15 7136
MULTIPLEX Li-BATT BX 3/4800 # 15 7150
Do not use the supplied Himax C 3528-1000 motor with
more than 3S LiPo or 9 NiXX cells when using the the
standard propeller.
4. SAFETY NOTES
The power set “MENTOR” is designed exclusively for use
in modelling applications. Incorrect use can result in
serious personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller
• Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
Operating Instructions for Power Set “MENTOR” # 82 6008 (08-02-21/DAMA) Errors and omissions excepted! © MULTIPLEX
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 1/2
5. ASSEMBLING OF THE POWER SET
“MENTOR“
Split taper
collet
Spinner holder
ELAPORSpinner nut
ELAPOR-Spinner
Propeller
driver
1. Screw the motor to the motor mount Æ ensure that the
motor is free to rotate. When deploying the motor
cables, check that they must not make contact with the
spinning motor. Secure the motor leads with velcro tape
or similar.
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propell er and the spinner holder on the propeller
driver, and secure them with the nut for the ELAPORspinner (supplied).
4. Clip the ELAPOR-spinner onto the spinner holder.
6. INITIATION OF THE POWER SET
“MENTOR”
1. Connect the three wires attached to the speed
controller to the three wires attached to the motor; the
order of connection is unimportant.
2. Locate the UNI connector attached to the speed
controller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the “OFF” position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
6. Switch the speed controller’s motor brake OFF; refer to
the controller’s instructions for details of the procedu re.
Operating Instructions for Power Set ”MENTOR”
7. NOTE REGARDING THE USE OF THE BEC
SYSTEM OF THE MULTICONT BL-54 SPEED
CONTROLLER
! In the model MENTOR, the BEC system of the
MULTIcont BL-54 speed controller is operated close
to its power limit. It is therefore absolutely essential
to observe the notes regarding the BEC system in the
operating instructions supplied with the MULTIcont
BL 54 (see Section 7. BEC = Battery Eliminator
Circuit); in case of doubt we recommend that you use
a separate receiver battery.
, AS SUPPLIED IN THE SET
8. HIMAX MOTOR - SPECIFICATION
Type: C 3528-1000
# 33 3028
RPM / V: 1000
Cell count, NiXX / LiPo: 6 - 9 / 2S - 3S
Efficient operating current: 15 A - 48 A
Max. current for 15 sec.: 68 A
Shaft Ø:
Diameter: 35 mm
Length: 54 mm
Weight: 197 g
Max. output: 450 W
Max. case temperature:
Mounting:
You will find comprehensive operating instructions for the
Himax C 3528-1000 at www.multiplex-rc.de Æ
DOWNLOADS Æ INSTRUCTIONS.
5.0 mm
65° C
∅ 25 mm / 4 x M3
10. CE APPROVAL
This product satisfies all the relevant statutory
harmonised EU directives.
You are therefore the owner of a product whose design
fulfils the protective aims of the European Community
relating to the safe operation of equipment.
You are entitled to obtain a copy of the conformity
declaration for this product by contacting MULTIPLEX
using the information at the foot of the page.
11. DISPOSAL INFORMATION
Electrical equipment marked with the cancelled
waste bin symbol must not be discarded in the
standard household waste; instead it must be
taken to a suitable specialist disposal system.
In the countries of the EU (European Union), electrical
equipment must not be discarded via the normal domestic
refuse system (WEEE – Waste of Electrical and
Electronic Equipment, directive 2002/96/EG). You can
take unwanted equipment to your nearest local authority
waste collection point or recycling centre, where the items
will be disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an
important contribution to the protection of the
environment.
9. GUARANTEE
MULTIPLEX products are covered by the statutory
guarantee regulations. If you wish to make a claim under
guarantee, please contact the model shop where you
purchased the product in the first instance.
The guarantee does not cover damage and malfunctions
caused by:
• Improper handling, incorrect connections, reversed
polarity
• Use of accessories other than genuine MULTIPLEX
items
• Modifications or repairs not carried out by MULTIPLEX
or an authorised MULTIPLEX Service Centre
• Accidental or deliberate damage
• Defects due to normal wear and tear
• Use outside the technical specifications
Operating Instructions for Power Set “MENTOR” # 82 6008 (08-02-21/DAMA) Errors and omissions excepted! © MULTIPLEX
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 2/2
Loading...