MTD 13AX604G402, 13AU604H402 Owner’s Manual

YaRD'MaN)[(

OPERATOR'S MANUAL

AutoDrive TM Lawn Tractor

Models

4,_ (13AX604G402)

-_e (13AU604H402)

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized

service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.

MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722

PRINTED IN U.S.A. FORM NO. 770-10236

(1/99)

SECTION 1: TABLE OF CONTENTS

PAGE

FINDING YOUR MODEL NUMBER ....................................................... 2

CALLING CUSTOMER SUPPORT ........................................................ 2

IMPORTANT SAFE OPERATION PRACTICES .............................................. 3

SAFETY LABLES FOUND ON YOUR UNIT ................................................. 5

SLOPE GAUGE ...................................................................... 6

ATTACHMENTS & ACCESSORIES ....................................................... 7

TRACTOR SET-UP .................................................................... 7

CONTROLS ......................................................................... 8

OPERATION ........................................................................ 11

ADJUSTMENTS ..................................................................... 14

MAINTENANCE ..................................................................... 17

LUBRICATION ...................................................................... 23

TROUBLESHOOTING GUIDE .......................................................... 24

PARTS LIST ........................................................................ 26

WARRANY INFORMATION ..................................................... Back Cover

SECTION 2: FINDING YOUR MODEL NUMBER

This Operator's Manual is an important part of your new rider. It will help you assemble, prepare and maintain

your rider. Please read and understand what it says. Before you start to prepare your tractor for its first use, please locate the model plate and copy the information

from it in this Operator's Manual. The information on the model plate is very important if you need help from your dealer or the MTD customer support department.

• Every tractor has a model plate. You can locate it by liftingthe seat and looking at the seat bracket.

• An example of what the model plate will look like is shown below.

This iswhere your model number will be.

This is where your serial number will be.

Copy the moder number here:

OHIO 44136

Copy the serial number here: _

SECTION 3: CALLING CUSTOMER SUPPORT

• LOCATE YOUR MODEL NUMBER AND SERIAL NUMBER -- Record this information in the space provided. To find your unit's specific model number and serial number, see SECTION 2: FINDING YOUR MODEL NUMBER.

• If you are having difficulty assembling this product or if you have any questions regarding the controls,

operation or maintenance of this unit, please call the Customer Support Department.

• Customer Support can be reached by dialing: 1- (330) 220-4MTD

(4683)

1- (800)-800-7310

• Please have your model number and serial number ready when you call.

• Although both numbers are important, you will be asked to enter only your serial number before your call can be processed.

SECTION 4: IMPORTANT SAFE OPERATION PRACTICES

WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF

NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF

YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE YOUR LAWN MOWER. FAILURE TO COMPLY WITH

THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL,

HEED ITS WARNING.

WARNING: The Engine Exhaust from this product contains chemicals known to

the State of California to cause cancer, birth defects or other reproductive harm.

DANGER: Your lawn mower was built to be operated according to the rules for safe operation in

this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This lawn mower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

1. GENERAL OPERATION

• Read, understand, and follow all instructions in the operator's manual and on the machine before starting. Keep this manual in a safe place for future and regular reference and for ordering replacement

parts.

• Only allow responsible individuals familiar with the instructions to operate the machine. Know controls

and how to stop the machine quickly.

• Do not put hands or feet under cutting deck or near rotating parts.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade. A small object may have been overlooked

and could be accidentally thrown by the mower in

any direction and cause injury to you or a bystander. To help avoid a thrown objects injury, keep children, bystanders and helpers at least 75 feet from the mower while it is in operation. Always wear safety glasses or safety goggles during operation or while performing an adjustment or repair, to protect eyes from foreign objects. Stop the blade(s) when crossing gravel drives, walks or roads.

• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area.

• Never carry passengers.

• Disengage blade(s) before shifting into reverse and

backing up. Always look down and behind before

and while backing.

• Be aware of the mower and attachment discharge

direction and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the chute guard in place.

• Slow down before turning. Operate the machine smoothly. Avoid erratic operation and excessive

speed.

• Never leave a running machine unattended. Always turn off blade(s), place transmission in neutral, set park brake, stop engine and remove key before dismounting.

• Turn off blade(s) when not mowing.

• Stop engine and wait until blade(s) comes to a complete stop before (a) removing grass catcher or unclogging chute, or (b) making any repairs,

adjusting or removing any grass or debris.

• Mow only in daylight or good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or unloading the machine into a trailer or truck. This unit should not

be driven up or down a ramp onto a trailer or truck under power, because the unit could tip over, causing serious personal injury. The unit must be pushed manually on a ramp to load or unload

properly.

• Never make a cutting height adjustment while engine is running if operator must dismount to do

so.

• Wear sturdy, rough-soled work shoes and close-

fitting slacks and shirts. Do not wear loose fitting clothes or jewelry. They can be caught in moving parts. Never operate a unit in bare feet, sandals, or

sneakers.

• Check overhead clearance carefully before driving under power lines, wires, bridges or low hanging tree branches, before entering or leaving buildings, or in any other situation where the operator may be struck or pulled from the unit, which could result in serious injury.

• Disengage all attachment clutches, thoroughly depress the brake pedal, and shift into neutral before attempting to start engine.

• Your mower is designed to cut normal residential grass of a height no more than 10". Do not attempt to mow through unusually tall, dry grass (e.g., pasture) or piles of dry leaves. Debris may build up on the mower deck or contact the engine exhaust

presenting a potential fire hazard.

2. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-

over accidents which can result in severe injury or death.

All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of

this manual to measure slopes before operating this unit on

a sloped or hilly area. If the slope is greater than 15° as shown on the slope gauge, do not operate this unit on that area or serious injury could result.

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, limbs, etc.

• Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide

obstacles.

• Use slow speed. Always keep machine in gear when going down slopes to take advantage of

engine braking action.

• Follow the manufacturer's recommendations for wheel weights or counterweights to improve

stability.

• Use extra care with grass catchers or other

attachments. These can change the stability of the machine.

• Keep all movement on the slopes slow and

gradual. Do not make sudden changes in speed or direction. Rapid engagement or braking could

cause the front of the machine to lift and rapidly flip over backwards which could cause serious injury.

• Avoid starting or stopping on a slope. If tires lose traction, disengage the blade(s) and proceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless necessary; then, turn slowly and gradually downhill, if possible.

• Do not mow near drop-offs, ditches or embankments. The mower could suddenly turn

over if a wheel is over the edge of a cliff or ditch, or

if an edge caves in.

• Do not mow on wet grass. Reduced traction could

cause sliding.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not use grass catcher on steep slopes.

3. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that chil- dren will remain where you last saw them.

• Keep children out of the mowing area and in watchful care of an adult other than the operator.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Never carry children, even with the blades off. They

may fall off and be seriously injured or interfere with

the safe machine operation.

• Never allow children under 14 years old to operate the machine. Children 14 years and over should

only operate machine under close parental supervision and proper instruction.

• Remove key when machine is unattended to prevent unauthorized operation.

• Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure

your vision of a child or other hazard.

4. SERVICE

• Use extreme care in handling gasoline and other fuels. They are extremely flammable and the

vapors are explosive.

• Use only an approved container.

• Never remove fuel cap or add fuel with the engine running. Allow engine to cool at least two minutes before refueling.

• Replace fuel cap securely and wipe off any spilled fuel before starting the engine as it may cause a fire or explosion.

• Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• Never refuel the machine indoors because fuel vaporswillaccumulate inthe area.

• Never store the fuel container or machine inside where there is an open flame or spark, such as a

gas hot water heater, space heater or furnace.

• Never run a machine inside a closed area,

• To reduce fire hazard, keep the machine free of

grass, leaves or other debris build-up. Clean up oil or fuel spillage. Allow machine to cool at least 5 minutes before storing.

• Before cleaning, repairing or inspecting, make certain the blade and all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the spark plug to prevent accidental starting.

• Check the blade and engine mounting bolts at

frequent intervals for proper tightness. Also, visually inspect blade for damage (e.g., excessive

wear, bent, cracked). Replace with blade which meets original equipment specifications.

• Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.

• Never tamper with safety devices. Check their

proper operation regularly. Use all guards as instructed in this manual.

• After striking a foreign object, stop the engine,

remove the wire from the spark plug and thoroughly inspect the mower for any damage. Repair the damage before restarting and operating the mower.

• Grass catcher components are subject to wear, damage and deterioration, which could expose

moving parts or allow objects to be thrown. For your safety protection, frequently check components and replace with manufacturer's recommended parts when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution

when servicing blade(s).

• Check brake operation frequently. Adjust and

service as required.

• Muffler, engine and belt guards become hot during operation and can cause a burn. Allow to cool down before touching.

Do not change the engine governor settings or

overspeed the engine. Excessive engine speeds

are dangerous.

Observe proper disposal laws and regulations.

Improper disposal of fluids and materials can harm

the environment and the ecology.

Prior to disposal, determine the proper method to dispose of waste from your local Environmental

Protection Agency. Recycling centers are established to properly dispose of materials in an environmentally safe fashion.

Use proper containers when draining fluids. Do not

use food or beverage containers that may mislead

someone into drinking from them. Properly dispose

of the containers immediately following the draining of fluids.

DO NOT pour oil or other fluids into the ground, clown a drain or into a stream, pond, lake or other body of water. Observe Environmental Protection Agency regulations when disposing of oil, fuel, coolant, brake fluid, filters, batteries, tires and other

harmful waste.

,_ WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons

who read, understand and follow the warnings and instructions in this manual and on the machine.

ASSEMBLE CHUTE DEFLECTOR

TO THIS UNIT

BEFORE OPERATING MACHINE.

DANGER

Figure 1 Safety Labels found on your unit

,-..,,= THIS PAGE AS A GUIDE TO DETERMINE SLOPE_, ..HERE YOU MAY NOT OPERATE SAFELY.

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

15°

_k WARNING

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain

your footing and you could slip, resulting in serious injury. Operate RIDING mowers up and down slopes, never across the face of slopes.

SECTION 5: ATTACHMENTS & ACCESSORIES

MODEL NUMBER

OEM-190-601 OEM-190-602

OEM-190-112

OEM-190-118 OEM-190-603 OEM-190-604

OEM-190-822

OEM-190-823

FastAttach: Twin Ba_r-Grass Collector (-For-42--inch_Decks Only i

FastAttach '°Twin Bagger Grass Collector (For 46-inch Decks Only)

Mulch Kit (For 42-inch Decks Only)

Mulch Kit (For 46-inch Decks Only) FastAttach'- Front Bumper Kit

TracPac" Storage Container (mounts on rear of tractor)

FastAt_ach'=46-inch Front Dozer Blade 42-inch Two-stage Snow Thrower

DESCRIPTION

SECTION 6: TRACTOR SET-UP

ATTACHING THE BATTERY CABLES GAS AND OIL FILL-UP

NOTE: The positive battery terminal is marked

Pos. (+). The negative battery terminal is marked

Neg. (-).

• The positive cable (heavy red wire) is secured to the positive battery terminal (+) with a hex bolt and hex nut at the factory. Make certain

that the rubber boot covers the terminal to help protect it from corrosion.

• Remove the hex bolt and wing nut from the

negative cable. Attach the negative cable (heavy black wire) to the negative battery

terminal (-) with the bolt and wing nut.

• Place the hold-down strap in position over the

battery to secure it in place. See Figure 2.

Positive Boot

Terminal _ : _

Service the engine with gasoline and oil as

instructed in the separate engine manual packed

with your tractor. Read instructions carefully,

IMPORTANT: Your tractor is shipped with oil;

however, you MUST check the oil level before oper- ating. Be careful not to overfill. Overfilling with oil

may cause the engine to smoke. This will result in

poor engine performance and could cause perma-

nent engine damage.

The gasoline tank is located under the hood and has a capacity of approximately two gallons. Do not

overfill.

WARNING: Gasoline produces noxious

fumes. Never fill fuel tank indoors. Always fill the fuel tank in a well ventilated area to

avoid inhalation of gasoline fumes.

Rubber i_

P f

Negative Hold-down !

_minel Bolt

Figure 2

NOTE: If battery is put into service after date

shown on top of battery, charge for minimum of one

hour at 6-10 amps. Refer to the MAINTENANCE

section of this manual for more detailed instructions

regarding proper battery charging procedure.

WARNING: Never smoke while fueling

your tractor or fill the fuel tank while engine is running or while engine is hot.

WARNING: Do not fill closer than 1/2 inch from the top of the fuel tank to prevent

spills and to allow for fuel expansion. If gasoline is accidently spilled, move tractor

away from area of spill. Avoid creating any source of ignition until gasoline vapors

have disappeared.

INSTALLING THE MULCH KIT

On units equipped with a 42-inch deck, the mulch kit is installed at the factory. To remove it, unfasten the

wing knob found on the top of the cutting deck and carefully pull the mulch plug out from the discharge

area of the deck. On units equipped with a 46-inch deck, the mulch kit

is packaged separately within the crate.

SECTION 7: CONTROLS

NOTE: Steering Wheel not shown for clarity.

Figure 3

A Ignition Switch H Brake Pedal

B Throttle Control Lever I Parking Brake Button

C PTO (Power Take-Off) Knob J Shift Lever D Indicator Monitor/Hour Meter K Seat Adjustment Lever

E Lift Lever L Cup Holder F Choke Control (if so equipped) M Cruise Control Button G AutoDrive- Pedal

NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator's position.

IGNITION SWITCH

To start the engine, insert key into the ignition switch

and turn clockwise to the START position. Release key to the ON position once engine has fired. See

Figure 4. Refer to STARTING THE ENGINE in the

OPERATION section of this manual for detailed

starting instructions. The ignition switch is also used to operate the headlights. Refer to OPERATING THE HEADLIGHTS in the OPERATION section of

this manual for detailed instructions

tractor when the tractor is not in use to

WARNING: Remove the key from the

prevent accidental starting.

Off

-- On/Lights

IMPORTANT: When using PTO operated

equipment such as the cutting deck or other attachments, always operate the tractor with the

throttle lever in the FAST (rabbit) position.

CHOKE CONTROL

On some units, moving the throttle lever all the way forward activates the engine's

choke control. On atl other units, the choke control can be

found on the left side of the

dash panel and is activated by pulling the knob outward. Activating the choke control closes the choke plate on the carburetor and aids in starting the engine. Refer to STARTING THE

ENGINE in the OPERATION section of this manual for detailed starting instructions.

t " - On

---- -- Start

Figure 4

THROTTLE CONTROL LEVER

The throttle lever is located on the right side of the tractor's dash panel. This lever controls the speed of the engine, and on some units the choke control

also. When set in a given position, the throttle will

maintain a uniform engine speed. See Figure 5.

Throttle Symbol

Choke

Position _

Fast

Position

Slow

Position

Throttle Symbol

Fast

Position

Slow

Position

INDICATOR MONITOR / HOUR METER

Your tractor is equipped with four indicator lights and an hour meter located on the left side of the dash

panel. See Figure 6.

BatterY

Hour

Meter

1/10

,-.

PTO

Figure 6

If a light illuminates when attempting to start the unit, proceed as follows: BRAKE-- Depress the brake pedal. PTO -- Move PTO switch into the disengaged

(OFF) position.

OIL-- Check the crankcase oil level, and add

oil as required. The BATTERY indicator light will illuminate any time the ignition key is the On position and the engine is

not running. If it illuminate's while the engine is running, it indicates that the battery is in need of a

charge. Refer to the MAINTENANCE section of this

manual for the proper battery charging procedure.

Oil

Brake

Figure 5

The hour meter operates whenever the ignition key

is in the On or On/Lights position and records the actual hours of tractor operation.

LIFT LEVER

BRAKE PEDAL

The lift lever is used to change the operating position

(height) of the cutting deck. To operate, move the lever to the left, then place in the notch best suited

for your application.

ELECTRIC PTO

(POWER TAKE-OFF) KNOB / _

To engage the power to the cutting deck or other attachments, pull outward on the PTO knob. Push the

PTO knob inward to disengage the power to the attachments.

NOTE: The PTO knob must be in the disengaged

(OFF) position when starting the engine, when shifting into reverse and if the operator leaves the

seat.

AUTODRIVE'-PEDAL

The brake pedal is located on the right front side of

the tractor above the AutoDrive.- pedal along the running board. The brake pedal can be used for

sudden stops or setting the parking brake.

NOTE: The brake pedal must be fully depressed to

activate the safety interlock switch when starting the

tractor.

PARKING BRAKE BUTTON

To set the parking brake, fully depress the brake pedal and push the parking

brake button in. Hold the button in

while taking your foot off the brake

pedal. Both the parking button and the brake pedal will then stay depressed. To release the parking brake, depress the brake pedal slightly. The parking brake button will then return to its original position.

NOTE: The parking brake must be set if the

operator leaves the seat with the engine running or the engine will automatically shut off.

The AutoDrive'- pedal is located below the brake

pedal on the right front side of the tractor along the running board. Depress the AutoDrive'- pedal with your right foot when the tractor shift lever is in either

forward or reverse to cause the tractor to move. Ground speed is also controlled with the AutoDrive-

pedal. The further down the pedal is depressed, the faster the tractor will travel. The pedal will return to

its original position when it's not depressed.

IMPORTANT: Always set the parking brake

when leaving the tractor unattended.

IMPORTANT: Always set the parking brake

when leaving the tractor unattended.

SHIFT LEVER

The shift lever is located on the left side of the

fender and has three positions, FORWARD,

NEUTRAL and REVERSE.

The brake pedal must be depressed and the tractor

must not be in motion when the moving shift

lever.

IMPORTANT: Never

force the shift lever. Doing

so may result in serious damage to the tractor's

transmission.

Shift

Knob

CRUISE CONTROLBUTTON

The cruise control button is located on the tractor dash panel to the left of the

ignition switch. Push the cruise control button while traveling forward at a desired speed. While holding the

button in, release pressure from the AutoDrive r-pedal. This will engage the

SEAT ADJUSTMENT LEVER

To adjust the seat forward or backward, slide the seat adjustment lever to the left and reposition the seat to the desired position. Once a comfortable position is found, release the seat adjustment lever to lock the seat in place. Refer to the

ADJUSTMENTS section of this manual for more

detailed instructions.

cruise control and allow the tractor to

remain at that speed without applying pressure to the AutoDrive r- pedal. Depress the brake pedal or the AutoDrive.- pedal to deactivate cruise

control. Refer to the OPERATION section of this

CUP HOLDER

The tractor's cup holder is located on the fender to the left of the seat, just to the rear of the shift lever.

AlL

manual for detailed instructions regarding the cruise ,_J_, control feature.

SECTION 8: OPERATION

SAFETY INTERLOCK SWITCHES

WARNING: Never operate the tractor

under the influence of alcoholic beverages or drugs of any kind. Doing so can result in serious personal injury or death.

This tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ever malfunction, do not operate the tractor. Contact an authorized MTD

Service Dealer in your area. The safety interlock

system prevents the engine from cranking or starting unless the brake pedal is fully depressed, and the

PTO switch is in the disengaged (OFF) position.

• The safety interlock system will automatically shut off the engine if the operator leaves the

seat before engaging the brake lock.

• The safety interlock system will automatically

shut off the engine if the operator leaves the seat with the PTO switch in the engaged (ON) position, regardless of whether the brake lock is engaged. The PTO switch must be in the disengaged (OFF) position to restart the engine.

• The safety interlock system will automatically shut off the PTO if the PTO switch is moved

into the engaged (ON) position with the shift

lever in the REVERSE position.

WARNING: Do NOT attempt to bypass

or disconnect the tractor's safety interlock.

Doing so could result in serious personal injury or death.

IMPORTANT: Tampering with or attempting to

bypass the tractors Safety Interlock Switches in any way WILL void your warranty.

WARNING

• GO UPAND DOWN SLOPES, NOT ACROSS.

• AVOID SUDDEN TURNS,

• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIR

• IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK DOWNHILL SLOWLY.

• DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.

• NEVER CARRY CHILDREN,

• LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.

• KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN PLACE AND WORKING

• REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADE(S).

• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.

• BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE PLAC- ING HANDS OR FEET NEAR BLADE(S).

• BEFORE LEAVING OPERATOR'S POSITION, DISENGAGE BLADE(S), PLACE THE SHIFT LEVER IN NEUTRAL, ENGAGE

BRAKE LOCK, SHUT ENGINE OFF AND REMOVE KEY.

AVOID SERIOUS INJURY OR DEATH

READ OPERATOR'S MANUAL

SETTING THE CUTTING HEIGHT

STOPPING THE ENGINE

Select the height position of the cutting deck by placing the deck lift lever in any of the six different cutting height notches on the right side of the fender. Then adjust the deck wheels so that they are at least

1/4 inch to 1/2 inch above the ground when the

tractor is on a smooth, flat surface such as a driveway.

dl_ WARNING: Keep hands and feet away

from the discharge chute opening of the cutting deck.

NOTE: The deck wheels are an anti-scalp feature

of the deck and are not designed to support the

weight of the cutting deck.

Refer to the ADJUSTMENTS section of this manual for more detailed instructions regarding various deck

adjustments.

STARTING THE ENGINE

NOTE: Refer to the TRACTOR SET-UP section of

this manual for Gasoline and Oil fill-up instructions.

• Insert the tractor key into the ignition switch.

• Place the PTO switch in the disengaged

(OFF) position.

• Depress the brake pedal and set the parking brake.

• Place the shift lever in the NEUTRAL position.

• Move the throttle control lever into the FAST (or CHOKE, if so equipped) position.

• Pull out the choke control knob, if so equipped (a warm engine may not require choking).

• Turn the ignition key clockwise to the START position. After the engine starts, release the

key. It will return to the ON position.

IMPORTANT: Do NOT hold the key in the START

position for longer than ten seconds at a time. Doing so may cause damage to your engine's starter.

• Place the PTO switch in the disengaged (OFF) position

• Move the throttle control into the SLOW (turtle) position and allow the engine to "idle

down" for ten seconds. Failure to do so may result in an engine afterfire.

• Turn the ignition key counterclockwise to the OFF position.

• Remove the key from the ignition switch to

prevent accidental starting.

IMPORTANT: If you think you've struck a foreign

object, stop the engine immediately. Remove the wire(s) from the spark plug(s), thoroughly inspect the unit for any damage, and repair the damage before restarting and operating the tractor.

DRIVING THE TRACTOR

,_ WARNING: Avoid sudden starts,

IMPORTANT: Do NOT use the shift lever to

change the direction of travel when the tractor is in motion. Always use the brake pedal to bring the tractor to a complete stop before shifting.

excessive speed and sudden stops.

tractor without first placing the PTO switch

WARNING: Do not leave the seat of the

in the disengaged (OFF) position, depressing the brake pedal and engaging the parking brake. If leaving the tractor

unattended, also turn the ignition key off

and remove the key.

• Depress the brake pedal to release the parking brake and let the pedal up. Move the

throttle lever into the FAST (rabbit) position.

• To move forward, place the shift lever in the FORWARD position, then slowly depress the

AuteDrive'- pedal until the desired speed is achieved.

NOTE: If starting problems are encountered, refer to the TROUBLESHOOTING section of this manual.

After the engine starts, slowly release the brake

pedal. As the engine warms up, gradually push the choke control knob inward (or move the throttle

control lever out of the CHOKE position into the FAST position) to open up the choke plate on the engine's carburetor.

NOTE: Do NOT leave the choke control out while

operating the tractor. Doing so will result in a "rich" fuel mixture and cause the engine to run poorly.

• To move in reverse, place the shift lever in the REVERSE position, check that the area behind is clear then slowly depress the AutoDrive- pedal.

SE'I-rlNG THE CRUISE CONTROL

NOTE: The cruise control feature should only be

utilized in the forward direction.

• Place the shift lever in the FORWARD position, then slowly depress the AutoDrive TM

pedal until the desired speed is achieved.

• Lightly depress the cruise control button.

+ 28 hidden pages