890FXA-GD70 series
MS-7640 (v1.x) Mainboard
G52-76401X1
Preface
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNA - TIONAL.
We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
MSI® is registered trademark of Micro-Star Int’l Co.,Ltd.
NVIDIA® is registered trademark of NVIDIA Corporation.
ATI® is registered trademark of ATI Technologies, Inc.
AMD® is registered trademarks of AMD Corporation.
Intel® is registered trademarks of Intel Corporation.
Windows® is registered trademarks of Microsoft Corporation.
AMI® is registered trademark of American Megatrends Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
Sound Blaster® is registered trademark of Creative Technology Ltd.
Realtek® is registered trademark of Realtek Semiconductor Corporation.
JMicron® is registered trademark of JMicron Technology Corporation.
Netware® is a registered trademark of Novell, Inc.
Revision |
History |
|
Revision |
Revision History |
Date |
V1.0 |
First release |
March 2010 |
Technical Support
If a problem arises with your system and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance.
◙Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates, and other information: http://www.msi.com/index.php?func=service
◙Contact our technical staff at: http://ocss.msi.com
ii
MS-7640
Safety Instructions
Always read the safety instructions carefully.
Keep this User’s Manual for future reference.
Keep this equipment away from humidity.
Lay this equipment on a reliable flat surface before setting it up.
The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet.
Place the power cord such a way that people can not step on it. Do not place anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or module.
All cautions and warnings on the equipment should be noted.
Never pour any liquid into the opening that could damage or cause electrical shock.
If any of the following situations arises, get the equipment checked by service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well or you can not get it work according to User’s Manual.
The equipment has dropped and damaged.
The equipment has obvious sign of breakage.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60oC (140oF), IT MAY DAMAGE THE EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
:
使用者會被要求採取某些適當的對策。
For better environmental protection, waste batteries should be collected separately for recycling special disposal.
iii
Preface
FCC -B Radio Frequency
Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7640
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)this device may not cause harmful interference, and
2)this device must accept any interference received, including interference that may cause undesired operation.
iv
MS-7640
WEEE (Waste Electrical
and Electronic
Equipment)
Statement
ENGLISH
To protect the global environment and as an environmentalist, MSI must re-
mind you that...
Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of “electrical and electronic equipment” cannot be discarded
as municipal waste anymore and manufacturers of covered electronic equip-
ment will be obligated to take back such products at the end of their useful life. MSI will comply with the product take back requirements at the end of life of MSI-branded products that are sold into the EU. You can return these products to local collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gemäß der Richtlinie 2002/96/EG über Elektround Elektronik-Altgeräte dürfen Elektro- und Elektronik-Altgeräte nicht mehr als kommunale Abfälle entsorgt werden. MSI hat europaweit verschiedene Sammelund Recyclingunternehmen beauftragt, die in die Europäische Union in Verkehr gebrachten Produkte, am Ende seines Lebenszyklus zurückzunehmen. Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgerätesammelstelle in Ihrer Nähe.
FRANÇAIS
En tant qu’écologiste et afin de protéger l’environnement, MSI tient à rappeler ceci...
Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer certains produits en fin de vie. MSI prendra en compte cette exigence relative au retour des produits en fin de vie au sein de la communauté européenne. Par conséquent vous pouvez retourner localement ces matériels dans les points de collecte.
РУССКИЙ
Компания MSI предпринимает активные действия по защите окружающей среды, поэтому напоминаем вам, что....
В соответствии с директивой Европейского Союза (ЕС) по предотвращению загрязнения окружающей среды использованным электрическим и электронным оборудованием (директива WEEE 2002/96/EC), вступающей в силу 13
августа 2005 года, изделия, относящиеся к электрическому и электронному оборудованию, не могут рассматриваться как бытовой мусор, поэтому производители вышеперечисленного электронного оборудования обязаны принимать его для переработки по окончании срока службы. MSI обязуется соблюдать требования по приему продукции, проданной под маркой MSI на территории EC, в переработку по окончании срока службы. Вы можете вернуть эти изделия в специализированные пункты приема.
Preface
ESPAÑOL
MSI como empresa comprometida con la protección del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unión Europea en materia de desechos y/o equipos electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como “eléctricos y equipos electrónicos” no pueden ser depositados en los contenedores habituales de su municipio, los fabricantes de equipos electrónicos, están obligados a hacerse cargo de dichos productos al termino de su período de vida. MSI estará comprometido con los términos de recogida de sus productos vendidos en la Unión Europea al final de su periodo de vida. Usted debe depositar estos productos en el punto limpio establecido por el ayuntamiento de su localidad o entregar a una empresa autorizada para la recogida de estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat….
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van hun levenscyclus. MSI zal overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI dragen en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op lokale inzamelingspunten.
SRPSKI
Da bi zaštitili prirodnu sredinu, i kao preduzeće koje vodi računa o okolini i prirodnoj sredini, MSI mora da vas podesti da…
Po Direktivi Evropske unije (“EU”) o odbačenoj ekektronskoj i električnoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju pod “elektronsku i električnu opremu” ne mogu više biti odbačeni kao običan otpad i proizvođači ove opreme biće prinuđeni da uzmu natrag ove proizvode na kraju njihovog uobičajenog veka trajanja. MSI će poštovati zahtev o preuzimanju ovakvih proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode možete vratiti na lokalnim mestima za prikupljanje.
POLSKI
Aby chronić nasze środowisko naturalne oraz jako firma dbająca o ekologię, MSI przypomina, że...
Zgodnie z Dyrektywą Unii Europejskiej (“UE”) dotyczącą odpadów produktów elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), która wchodzi w życie 13 sierpnia 2005, tzw. “produkty oraz wyposażenie elektryczne i elektroniczne “ nie mogą być traktowane jako śmieci komunalne, tak więc producenci tych produktów będą zobowiązani do odbierania ich w momencie gdy produkt jest wycofywany z użycia. MSI wypełni wymagania UE, przyjmując produkty (sprzedawane na terenie Unii Europejskiej) wycofywane z użycia. Produkty MSI będzie można zwracać w wyznaczonych punktach zbiorczych.
vi
MS-7640
TÜRKÇE
Çevreci özelliğiyle bilinen MSI dünyada çevreyi korumak için hatırlatır:
Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü olacaktır. Avrupa Birliği’ne satılan MSI markalı ürünlerin kullanım süreleri bittiğinde MSI ürünlerin geri alınması isteği ile işbirliği içerisinde olacaktır. Ürünlerinizi yerel toplama noktalarına bırakabilirsiniz.
ČESKY
Záleží nám na ochraně životního prostředí - společnost MSI upozorňuje...
Podle směrnice Evropské unie (“EU”) o likvidaci elektrických a elektronických výrobků 2002/96/EC platné od 13. srpna 2005 je zakázáno likvidovat “elektrické a elektronické výrobky” v běžném komunálním odpadu a výrobci elektronických výrobků, na které se tato směrnice vztahuje, budou povinni odebírat takové výrobky zpět po skončení jejich životnosti. Společnost MSI splní požadavky na odebírání výrobků značky MSI, prodávaných v zemích EU, po skončení jejich životnosti. Tyto výrobky můžete odevzdat v místních sběrnách.
MAGYAR
Annak érdekében, hogy környezetünket megvédjük, illetve környezetvédőként fellépve az MSI emlékezteti Önt, hogy ...
Az Európai Unió („EU”) 2005. augusztus 13-án hatályba lépő, az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint az elektromos és elektronikus berendezések többé nem kezelhetőek lakossági hulladékként, és az ilyen elektronikus berendezések gyártói kötelessé válnak az ilyen termékek visszavételére azok hasznos élettartama végén. Az MSI betartja a termékvisszavétellel kapcsolatos követelményeket az MSI márkanév alatt az EU-n belül értékesített termékek esetében, azok élettartamának végén. Az ilyen termékeket a legközelebbi gyűjtőhelyre viheti.
ITALIANO
Per proteggere l’ambiente, MSI, da sempre amica della natura, ti ricorda che….
In base alla Direttiva dell’Unione Europea (EU) sullo Smaltimento dei Materiali Elettrici ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla categoria dei Materiali Elettrici ed Elettronici non possono più essere eliminati come rifiuti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita. MSI si adeguerà a tale Direttiva ritirando tutti i prodotti marchiati MSI che sono stati venduti all’interno dell’Unione Europea alla fine del loro ciclo di vita. È possibile portare i prodotti nel più vicino punto di raccolta
vii
Preface
Contents
Copyright |
Notice |
ii |
Trademarks |
ii |
|
Revision |
History |
ii |
Technical |
Support |
ii |
Safety Instructions |
iii |
|
FCC-B Radio Frequency Interference Statement |
iv |
|
WEEE (Waste Electrical and Electronic Equipment) Statement |
v |
|
Chapter 1 Getting Started |
1-1 |
Mainboard Specifications 1-2
Mainboard Layout 1-4
Packing Checklist 1-5
Chapter 2 Hardware Setup 2-1
Quick Components Guide 2-2
CPU (Central Processing Unit) 2-3
Memory 2-6
Power Supply 2-8
Back Panel 2-9
Connectors 2-11
Jumpers 2-18
Button 2-19
Slots 2-21
LED Status Indicators 2-25
Chapter 3 BIOS Setup 3-1
Entering Setup 3-2
The Main Menu 3-4
Standard CMOS Features 3-6
Advanced BIOS Features 3-8
Integrated Peripherals 3-10
Power Management Setup 3-12
H/W Monitor 3-14
Green Power 3-15
BIOS Setting Password 3-16
Cell Menu 3-18
M-Flash 3-24
Overclocking Profile 3-27
Load Fail-Safe/ Optimized Defaults 3-28
viii
MS-7640 |
Appendix A Realtek Audio A-1 |
Installing the Realtek HD Audio Driver A-2 |
Software Configuration A-3 |
Hardware Default Setting A-5 |
Appendix B AMD RAID B-1 |
RAID Configuration B-2 |
ix |
Chapter1
Getting Started
Thank you for choosing the 890FXA-GD70 Series (MS7640 v1.X) ATX mainboard. The 890FXA-GD70 Series mainboards are based on AMD® RD890 & SB850 chipsets for optimal system efficiency. Designed to fit the advanced AMD® 64 bits PhenomTM II X6/ X4/ X3/ X2, AthlonTM II
X4/ X3/ X2 and Sempron processor, the 890FXA-GD70 Series deliver a high performance and professional desktop platform solution.
1-1-1
Getting Started
Mainboard Specifications
Processor Support
■AMD® PhenomTM II X6/ X4/ X3/ X2, AthlonTM II X4/ X3/ X2 and Sempron processor in the AM3 package.
(For the latest information about CPU, please visit http://www.msi.com/index. php?func=cpuform2)
HyperTransport
■ HyperTransport™ 3.0, supports up to 5.2 GT/s
Chipset
■North Bridge: AMD® RD890 chipset
■South Bridge: AMD® SB850 chipset
Memory Support
■DDR3 2133 *(OC)/ 1800 *(OC)/ 1600 *(OC)/ 1333/ 1066 SDRAM (total 16 GB Max)
■4 DDR3 DIMMs, supports Dual-Channel mode
*(For more information on compatible components, please visit http://www.msi.com/index.php?func=testreport)
LAN
■ Supports Dual PCIE Gb LAN (10/100/1000) by Realtek® RTL8111DL
IEEE 1394
■Chip integrated by VIA® VT6315N
■2 IEEE 1394 ports
Audio
■HD audio codec integrated by Realtek® ALC889/ ALC892
■Flexible 8-channel audio with jack sensing
IDE
■1 IDE port by JMicron® JMB363
■Supports Ultra DMA 66/100/133, PIO & Bus Master operation mode
SATA
■6 SATA 6Gb/s ports (SATA1~6) by AMD® SB850
■1 E-SATA/ USB Combo port (back panel) and 1 SATA 3Gb/s port (SATA7) by JMicron® JMB363
■Supports hot plug & asynchronous notification
USB 3.0
■ 2 USB 3.0 ports (blue, back panel) by NEC uPD720200F1
RAID
■ SATA1~6 support RAID 0/ 1/ 5/ 10 mode by AMD® SB850
1-2
MS-7640
Connectors
■Back panel
-1 PS/2 keyboard port
-1 PS/2 mouse port
-1 Clear CMOS button
-1 Coaxial S/PDIF-out port
-1 Optical S/PDIF-out port
-5 USB 2.0 ports (black)
-2 USB 3.0 ports (blue)
-1 ESATA/ USB 2.0 Combo port
-2 LAN ports
-6 flexible audio ports
■On-Board
-3 USB 2.0 connectors
-2 IEEE 1394 connectors
-1 Chassis Intrusion connector
-1 S/PDIF-out connector
-1 Front Panel Audio connector
-1 TPM Module connector
-1 Power button
-1 Reset button
-1 OC Dial button
-1 OC Dial knob
-1 Green Power button
-1 Debug LED panel
Slots
■4 PCI Express 2.0 x16 slots, support up to PCIE 2.0 x16 speed
■1 PCI Express 2.0 x16 slot, supports up to PCIE 2.0 x4 speed (PCI_E4)
■1 PCI Express 2.0 x1 slot
■1 PCI slot, supports 3.3V/ 5V PCI bus Interface
Form Factor
■ ATX (24.5cm X 30.5 cm)
Mounting
■ 9 mounting holes
Features on Focus
■USB 3.0
■SATA 6Gb/s
■DrMOS inside
■Half Hi-C Cap design
■Active Phase Switch feature to save power dynamically
■OC Genie Lite
■OC Dial
■Easy Button 2
■USB Safeguard
■M-Flash included
■CrossFireXTM
1-3
Getting Started
Mainboard Layout
Top : mouse |
SYSFAN1 |
Bottom:keyboard |
|
Clear CMOS button |
|
Top: |
JPWR2 |
Buttom: |
|
Coaxial S/PDIF |
|
Optical S/PDIF |
|
USB 2.0 ports |
|
Top: USB 2.0 port
Buttom: E-SATA Combo port
Top: LAN Jack
Bottom: USB 2.0 ports
CPUFAN
AM3 SOCKET
JPWR1
Top: LAN Jack |
|
|
|
AMD |
|
|
|
Bottom: USB 3.0 ports |
|
|
|
|
|||
|
RD890 |
|
|
|
|||
|
|
|
|
|
DIMM1 |
DIMM2 DIMM3 DIMM4 |
|
T:Line-In |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
M:Line-Out |
|
|
|
|
|
|
|
B:Mic |
|
|
|
|
|
|
|
T:RS-Out |
|
|
|
|
|
|
|
M:CS-Out |
|
|
PCI_E1 |
|
|
|
|
B:SS-Out |
|
|
|
|
|
||
USB 3.0 |
|
|
|
|
|
||
Chip |
|
|
|
|
|
|
|
|
|
|
PCI_E2 |
|
|
|
|
LAN |
|
|
PCI_E3 |
|
|
|
|
Chip |
|
|
|
|
|
|
|
LAN |
|
PCI_E4 |
|
|
|
||
Chip |
|
|
|
AMD |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SB850 |
1394 |
|
|
PCI_E5 |
|
|
|
|
|
|
|
|
|
JCI1 |
|
|
Chip |
|
|
|
|
|
|
|
|
SYSFAN4 |
PCI1 |
|
|
I/O |
BATT + |
|
|
PCI_E6 |
|
|||||
|
|
|
|
|
|
|
|
ALC889 |
|
|
|
|
|
Chip |
|
/ ALC892 |
|
|
|
|
|
JCOM1 |
|
|
|
|
|
|
|
|
JTPM1 |
|
|
|
|
JUSB1 |
JUSB2 |
JUSB3 |
OC GEAR |
|
|
|
|
|
|
JBAT1 Green |
|
JAUD1 |
|
JSP1 |
J1394_1 |
J1394_2 |
|
|
Power |
|
|
|
Green Power |
JSMB1
SYSFAN2 |
|
JMB363 |
|
IDE1 |
|
SATA7 |
SATA1_2 |
SYSFAN3 |
SATA3_4 |
|
SATA5_6 |
JFP1 JFP2 |
|
OC DRIVE |
|
RESET |
|
RESET1 |
POWER1 |
890FXA-GD70 Series (MS-7640 v1.X) ATX Mainboard
1-4
MS-7640
Packing Checklist
MSI mainboard |
MSI Driver/Utility DVD |
SATA Cable |
Power Cable |
USB Bracket (Optional) |
Standard Cable for |
|
|
IDE Devices |
CrossFireX Video Link |
Back IO Shield |
User’s Guide |
cable |
|
|
* The pictures are for reference only and may vary from the packing contents of the product you purchased. If you need to purchase accessories and request the part numbers, you could search the product web page and find details on our web address http://www.msi.com/index.php
1-5
Chapter2
Hardware Setup
This chapter provides you with the information about hardware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly.
Use a grounded wrist strap before handling computer components. Static electricity may damage the components.
2-2-1
Hardware Setup
Quick Components Guide
JPWR2, p.2-8 |
CPU, p.2-3 |
CPUFAN, p.2-13 |
|||
SYSFAN1, p.2-13 |
JCI1, p.2-12 |
SYSFAN3, p.2-13 |
DDR3, p.2-6 |
JSMB1, p.2-16
BackPanel, |
SYSFAN2, p.2-13 |
|
p.2-9 |
||
|
||
|
JPWR1, p.2-8 |
PCIE, p.2-21 |
IDE1, p.2-11 |
|
|
SATA, p.2-12 |
PCI, p.2-24 |
|
|
SYSFAN4, p.2-13 |
|
JFP1/ JFP2, p.2-14 |
|
JTPM1, p.2-17 |
|
JAUD1, p.2-13 |
|
|
|
|
|
JSP1, p.2-14 |
|
POWER1, p.2-19 |
J1394_1/2, p.2-16 |
JUSB1~3, p.2-15 |
RESET1, p.2-19 |
|
JCOM1, p.2-15 |
OC DRIVE, p.2-20 |
|
JBAT1, p.2-18 |
OC GEAR, p.2-20 |
|
Green Power, p.2-19 |
2-2
MS-7640
CPU (Central Processing Unit)
When you are installing the CPU, make sure to install the cooler to prevent overheating. If you do not have the CPU cooler, consult your dealer before turning on the computer.
For the latest information about CPU, please visit http://www.msi.com/index. php?func=cpuform2
Important
Overheating
Overheating will seriously damage the CPU and system. Always make sure the cooling fan can work properly to protect the CPU from overheating. Make sure that you apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
Replacing the CPU
While replacing the CPU, always turn off the ATX power supply or unplug the power supply’s power cord from the grounded outlet first to ensure the safety of CPU.
Overclocking
This mainboard is designed to support overclocking. However, please make sure your components are able to tolerate such abnormal setting, while doing overclocking. Any attempt to operate beyond product specifications is not recommended. We do not guarantee the damages or risks caused by inadequate operation or beyond product specifications.
2-3
Hardware Setup
CPU & Cooler Installation
When you are installing the CPU, make sure the CPU has a cooler attached on the top to prevent overheating. Meanwhile, do not forget to apply some thermal paste on CPU before installing the heat sink/cooler fan for better heat dispersion.
Follow the steps below to install the CPU & cooler correctly. Wrong installation will cause the damage of your CPU & mainboard
1.Pull the lever sideways away from the socket. Make sure to raise the lever up to a 90-degree angle.
2.Look for the gold arrow of the CPU. Thegoldarrowshouldpointasshown in the picture. The CPU can only fit in the correct orientation.
3.If the CPU is correctly installed, the pins should be completely embedded into the socket and can not be seen. Please note that any violation of the correct installation procedures may cause permanent damages to your mainboard.
4.Press the CPU down firmly into the socket and close the lever. As the CPU is likely to move while the lever is being closed, always close the lever with your fingers pressing tightly on top of the CPU to make sure the CPU is properly and completely embedded into the socket.
2-4
|
MS-7640 |
|
|
5. Position the cooling set onto the re- |
6. Then press down the other end of the |
tention mechanism. |
clip to fasten the cooling set on the |
Hook one end of the clip to hook |
top of the retention mechanism. |
first. |
Locate the Fix Lever and lift up it. |
7. Fasten down the lever. |
8. AttachtheCPUFancabletotheCPU |
|
fan connector on the mainboard. |
Important
•Mainboard photos shown in this section are for demonstration only. The appearance of your mainboard may vary depending on the model you purchase.
•While disconnecting the Safety Hook from the fixed bolt, it is necessary to keep an eye on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the fixed lever will spring back instantly.
2-5
Hardware Setup
Memory
These DIMM slots are used for installing memory modules. For more information on compatible components, please visit http://www.msi.com/index.php?func=testreport
DDR3
240-pin, 1.5V
72x2=144 pin |
48x2=96 pin |
Dual-Channel
mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive data with two data bus lines simultaneously. Enabling Dual-Channel mode can enhance the system performance. The following illustrations explain the population rules for Dual-Channel mode.
1 DIMM1
DIMM2
DIMM3
DIMM4
2 DIMM1
DIMM2
DIMM3’
DIMM4
Installed
Empty
Important
•DDR3 memory modules are not interchangeable with DDR2 and the DDR3 standard is not backwards compatible. You should always install DDR3 memory modules in the DDR3 DIMM slots.
•In Dual-Channel mode, make sure that you install memory modules of the same type and density in different channel DIMM slots.
•To enable successful system boot-up, always insert the memory modules into the DIMM1 first.
•Due to the chipset resource deployment, the system density will only be detected up to 15+GB (not full 16GB) when each DIMM is installed with a 4GB memory module.
2-6
MS-7640
Installing Memory Modules
1.The memory module has only one notch on the center and will only fit in the right orientation.
2.Insert the memory module vertically into the DIMM slot. Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot. The plastic clip at each side of the DIMM slot will automatically close when the memory module is properly seated.
3.Manually check if the memory module has been locked in place by the DIMM slot clips at the sides.
Notch
Volt
Important
You can barely see the golden finger if the memory module is properly inserted in the DIMM slot.
2-7
Hardware Setup
Power Supply
ATX 24-pin Power Connector: JPWR1
This connector allows you to connect an ATX 24-pin power supply. To connect the ATX 24-pin power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector.
You may use the 20-pin ATX power supply as you like. If you’d like to use the 20-pin ATX power supply, please plug your power supply along with pin 1 & pin 13 (refer to the image at the right hand).
|
|
|
|
|
|
|
|
12 |
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
11 |
|
|
. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
10 |
|
. +3. |
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
+12V |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
9 . |
|
|
3 |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
8 |
. |
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
V |
|
|
|
|
|
|
||
|
|
|
|
|
6 . |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 . |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
1 |
|
|
4 |
. +5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
3 . |
Ground |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
2 |
|
. +5 |
|
|
|
|
|
|
|
|
|
|
|
24 |
|
|
||||
|
|
.GroundV |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
. |
|
|
|
V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
. +3 |
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
+3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
. |
|
|
|
|
|
|
|
|
|
|
|
23. |
|
|||
|
|
|
|
V |
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
3 |
|
|
|
|
|
|
|
|
|
|
|
+5 |
|
. |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GroundV |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
. +5 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+5 |
V |
V |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.Ground |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
. |
- |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
13. |
- |
ON |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
+3 |
12V |
|
# |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
V |
|
|
|
|
|
|
ATX 8-pin Power Connector: JPWR2
This connector is used to provide +12V power.
|
|
|
4 |
|
|
|
|
|
|
. |
|
|
|
|
|
3 |
Ground |
|
|
|
|
|
. |
|
|
|
|
|
2 |
Ground |
|
|
|
|
|
. |
|
|
|
|
|
1 |
Ground |
|
|
|
||
. |
|
|
|
|
|
|
Ground |
|
|
|
|||
|
|
|
|
|
|
8 |
|
|
|
5 |
|
|
. |
|
|
|
|
7 |
+12V |
|
|
|
|
|
|
. |
|
|
|
|
|
6 |
+12V |
|
|
|
|
|
. |
|
|
|
|
|
|
+12V |
||
|
|
|
. |
|
|
|
|
|
|
+12V |
Important
•Make sure that all the connectors are connected to proper ATX power supplies to ensure stable operation of the mainboard.
•Power supply of 400 watts (and above) is highly recommended for system stability.
2-8
USB Port
MS-7640
Back Panel
Mouse |
Coaxial |
|
LAN |
LAN |
|
S/PDIF-Out |
|
|
|
|
|
|
|
|
|
|
|
|
|
USB |
2.0 |
Line-In RS-Out |
|
|
|
Port |
|
|
|
|
Clear |
|
|
|
|
|
CMOS |
|
|
Line-OutCS-Out |
|
|
Button |
|
|
|
|
|
|
|
|
Mic |
SS-Out |
Keyboard |
USB 2.0 Port |
|
USB 2.0 Port |
USB 3.0 Port |
|
|
Optical |
ESATA/ USB 2.0 |
|
|
|
|
S/PDIF-Out |
Combo Port |
|
|
Mouse/Keyboard
The standard PS/2® mouse/keyboard DIN connector is for a PS/2® mouse/keyboard.
Clear CMOS Button
There is a CMOS RAM on board that has a power supply from external battery to keep the system configuration data. With the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, use the button to clear data. Press the button to clear the data.
Important
Make sure that you power off the system before clearing CMOS data.
After pressing this button to clear CMOS data in power off (G3) state, the system will boot automatically.
Coaxial S/PDIF
-Out
This SPDIF (Sony & Philips Digital Interconnect Format) connector is provided for digital audio transmission to external speakers through a coaxial cable.
Optical S/PDIF
-Out
This SPDIF (Sony & Philips Digital Interconnect Format) connector is provided for digital audio transmission to external speakers through an optical fiber cable.
USB 2.0 Port
The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard, mouse, or other USB-compatible devices. Supports data transfer rate up to 480Mbit/s (Hi-Speed).
2-9
Hardware Setup
USB 3.0 Port
USB 3.0 port is backward-compatible with USB 2.0 devices. Supports data transfer rate up to 5 Gbit/s (SuperSpeed).
Important
If you want to use a USB 3.0 device, you must use the USB 3.0 cable to connect to the USB 3.0 port.
ESATA/ USB 2.0 Combo Port
The ESATA/USB 2.0 combo port is for attaching the ESATA external hard drive or USB device.
LAN |
|
|
|
|
The standard RJ-45 LAN jack is for connection to the Yellow |
Green/ Orange |
|||
Local Area Network (LAN). You can connect a net- |
|
|||
work cable to it. |
|
|
|
|
LED |
Color |
LED State |
Condition |
|
Left |
Yellow |
Off |
LAN link is not established. |
|
|
|
On(Steady state) |
LAN link is established. |
|
|
|
On(brighter & pulsing) |
The computer is communicating with another computer on the LAN. |
|
Right |
Green |
Off |
10 Mbits/sec data rate is selected. |
|
|
|
On |
100 Mbits/sec data rate is selected. |
|
|
Orange |
On |
1000 Mbits/sec data rate is selected. |
|
Audio Ports
These audio connectors are used for audio devices. It is easy to differentiate between audio effects according to the color of audio jacks.
■Line-In (Blue) - Line In, is used for external CD player, tape-player or other audio devices.
■Line-Out (Green) - Line Out, is a connector for speakers or headphones.
■Mic (Pink) - Mic, is a connector for microphones.
■RS-Out (Black) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode.
■CS-Out (Orange) - Center/ Subwoofer Out in 5.1/ 7.1 channel mode.
■SS-Out (Gray) - Side-Surround Out 7.1 channel mode.
2-10
MS-7640
Connectors
IDE Connector:
IDE1
This connector supports IDE hard disk drives, optical disk drives and other IDE devices.
* The MB layout in this figure is for reference only.
Important
If you install two IDE devices on the same cable, you must configure the drives separately to master / slave mode by setting jumpers. Refer to IDE device’s documentation supplied by the vendors for jumper setting instructions.
2-11