Mountain Off Road WTB100 User Manual

MOUNTAIN OFF ROAD ENTERPRISES LLC.

P O BOX 690 DELTA COLORADO 81416

970-625-0500

E-mail: info@mountainoffroad.com

www.mountainoffroad.com

Instructions for WTB100 - DoubleJointed™ “Front” Trac Bar

Please read Terms / Policies on page 2 before you begin installation.

CONTENTS:

1– Trac Bar 23” long 1– Heim Joint 3/4” L.H. thread with jam nut 1– Heim Joint 3/4” R.H. thread with jam nut 2– .125” Shoulder Spacers zinc plated (axle end) 1– 1/2” x 3” Grade 8 Bolt (axle end) 2– .3125 Shoulder Spacers zinc plated (Frame End) 1– 1/2” x 4-1/2” Grade 8 Bolt (Frame End) 2– Crimp-Loc nuts 1– 1.85” long x 1” diameter spacer tube (zinc plated)

Please note. There has been some confusion about where this trac bar mounts. It is for the ing this on a XJ Cherokee, TJ Wrangler or on the rear of a YJ.

1. Remove O.E. FRONT trac bar from vehicle, including mounting hardware and “U” bracket from

the drivers side of the frame. Also, remove and discard any aftermarket riser bracket (that had been installed with aftermarket suspension lift kit) from the axle end.

2. With a 1/2” bit in a power drill, enlarge the hole on the front axle to 1/2”. (It is metric size from

the factory).

3. Install the 1.85” long x 1” diameter spacer tube into the frame bracket where the stock trac bar

originally mounted. This spacer tube will keep the bracket from collapsing.

4. Install the Heim Joints into the trac bar. Remember, there are left and right threads, don’t

cross thread them!!! It doesn’t matter if the right threads go on the axle end or the frame end. Sandwich Heim Joints between both shoulder spacers. The thick (.3125”) spacers go on the frame end. Mount the trac bar to the axle with the 1/2” x 3” bolt. Mount the bar 1/2” x 4-1/2” bolt. Tighten both 1/2” bolts to 85 LB. FT. torque. Adjust the length of the bar by turning the bar with a 7/8” wrench using the flats machined into ether end of the bar. Note: there must be at lease 3/4” of the Heim Joint threads in the bar for proper strength!!! Tighten the jam nuts for the Heim

Joints with a 1-1/8” wrench by hand. Do not over tighten these jam nuts. Note: If you get a slight amount of interference between the frame bracket and the Trac Bar, grind clearance on the frame bracket until the Heim Joint and jam nut clears it.

PAGE 1 of 2

front axle only

on Jeep® YJ Wrangler vehicles. Do not even think about install-

BEHIND

the O.E. bracket with the

TERMS-POLICIES:

DAMAGE CLAIMS: All orders are carefully packed, however, mishandling by the carrier can result in dam-

age. The carrier has the responsibility for the shipment from the time it leaves our warehouse until it is delivered to you. All claims for lost or damaged goods should be reported to the carrier, not to M.O.R.E.™ LLC.

RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. After you receive a Return Goods Authorization (RGA) number, merchandise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original invoice or a copy with the RGA number written on must accompany all returns. A 20% restocking fee will be charged on all parts returned for credit or refund unless merchandise is proven to be defective or was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit or refund if it has been installed, modified, used in any way or is in unsalable condition.

WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper use will void this warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or guarantee the performance of any items. M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite variety of conditions due to the manner in which they are used, serviced and/or installed. Purchasers and users of such products rely upon their own judgment as to the suitable use selection, service and installation of such products.

PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E LLC. may create a dangerous condition which could cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All parts sold by M.O.R.E.™ Inc. are for racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for personal injury or property damage arising from the failure of any parts manufactured or sold by M.O.R.E.™ LLC.

Specifications are subject to change without notice.

Jeep®,TJ®, XJ®, YJ®, Cherokee®, Wrangler®, are registered trademarks of the DaimlerChrysler.

1999-2008.

PAGE 2 of 2