Mountain Off Road WCK200 User Manual

MOUNTAIN OFF-ROAD ENTERPRISES LLC.
P O BOX 690 DELTA COLORADO 81416

970-625-0500 970-625-3747 Fax

www.mountainoffroad.com

e-mail: [e-mail]

Jeep® TJ WRANGLER SPORT CAGE #WCK200

—– INSTALLATION INSTRUCTIONS —–

Read all instructions and Terms-Policies before installing this Sport Cage. If you are installing additional

overhead bars, read those instructions before installing this Sport Cage.

TERMS-POLICIES:

THIS SPORT CAGE IS A DECORATIVE ACCESSORY DESIGNED FOR APPEARANCE PURPOSES ONLY. DO

NOT RELY ON IT AS PROTECTION FROM VEHICLE ROLL OVER.

FIT and TOLERANCES: All parts that M.O.R.E.™ sells are the results of countless hours of research, testing, fitting and refining. Jeep® vehicles have a
wide tolerances from vehicle to vehicle. In addition to the factory tolerances, some people install aftermarket equipment that may not be compatible with this
M.O.R.E.™ accessory. M.O.R.E.™ has done the best job we can to insure that our parts fit with all of the possibilities. However, you may find it necessary to
grind, elongate, bend, or force the parts in this kit, to fit on your rig. Please use common sense when installing these parts, and understand that if you modify them in
any way, shape or form, they are not returnable!
RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. You must call for a Return Goods Authorization (RGA) number. Merchandise
must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original invoice or a copy with the RGA number writ­ten on must accompany all returns. A 20% restocking fee will be charged on all parts returned for credit or refund unless merchandise is proven to be defective or
was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit or refund if it has been installed, modified, used in any way or is in unsalable condi tion.
WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper use will void
this warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or guarantee the performance of any items.
M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite variety of conditions due to the manner in which they
are used, serviced and/or installed. Purchasers and users of such products rely upon their own judgment as to the suitable use selection, service and installation of
such products.
PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous condition which
could cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All parts sold by M.O.R.E.™ LLC., are
for off road use only and never to be used on a public road or highway. Mountain Off Road Enterprises LLC. will not accept r esponsibility for personal injury or prop­erty damage arising from the failure of any parts manufactured or sold by M.O.R.E.™ LLC.
Jeep® , AMC® , CJ® , YJ® , TJ®, Wrangler® , are registered trademarks of DaimlerChrysler . Mountain Off Road Enterprises, LLC. is in no way affiliated with
DaimlerChrysler.
M.0.R.E™, BombProof™, S.R.S.™, SlipLoc™, DoubleJointed™, RockProof™, are trademarks used by Mountain Off Road Enterprises, LLC. The M.O.R.E.™
logo and these instructions are copyright©, 2000-2008.

Specifications are subject to change without notice.

This Sport Cage Part # WCK200 fits 1997-2000 Jeep® TJ Wrangler vehicles. It will fit with hard top, or soft top, full
hard doors or half hard doors. It uses two curved bars to attach to the factory roll bar in place of the stock horizontal
bars that attach to the windshield frame. The cross bar connects the left & right side bars together just behind the
windshield frame. The stock latches for the top will clear the Sport Cage cross bar. The sun visors can be retained
in the stock location. All necessary hardware is provided. We recommend pre-fitting this Sport Cage before you paint
it. This Sport Cage has been designed to be as easy to install as possible. The following tools are required for instal-

lation: 3/8” drill bit & power drill, #40 Torx, #50 Torx (tamper proof-now included with this kit), ratchet, 9/16” socket &
wrench, 13/16” socket, round (rat-tail) file.

CONTENTS:

1-LEFT SIDE BAR
1-RIGHT SIDE BAR
1-CROSS BAR
1-DRIVERS SIDE “L” BRACKET (Sport Cage to W/S frame)
1-PASSENGER SIDE “L” BRACKET (Sport Cage to W/S frame)
2-BOLTS-3/8”X2-1/4” (Through bolts-cross bar to L&R side bars)
2-CRIMP-LOC NUTS-3/8”
2-WASHERS-FLAT 3/8”
2-BOLTS-9/16”X1-1/2”
2-WASHERS-SPLIT-LOCK
2-WASHERS-FLAT 9/16”X2”
1-#50 TORX® BIT (tamperproof)
1-INSTRUCTION SHEET

Specs:
Tubing: 1-3/4” O.D. x .120w
H.R.E.W. Steel.
Floor Plates: 7 Gauge H.R.
Steel, P&O.
Hardware: Grade 5

——— STEP BY STEP INSTRUCTIONS TO INSTALL THE TJ SPORT CAGE: ————

This Sport Cage can be installed with the top (hard or soft) on the Jeep®. However, M.O.R.E.™ recom-
mends removing the top for installation. All of the pictures in these instructions are with the top removed.

1. UN-zip padding from factory roll bar

2. Remove the factory horizontal bars that connect the roll bar to the windshield (W/S) frame. The simplest

way is to remove the stub from the roll bar (two #40 Torx head bolts per bar), then remove the two #40 Torx
head bolts from the W/S frame. See Figure 1.

3. Remove the factory stubs from the horizontal bars with the #50 Torx® bit (tamperproof) included with this
kit. Keep in mind that there is a left and right stub. See Figure 2.

4. If your Jeep® is equipped with carpet, pull it away from the sides of the body tub to expose the drain holes
in the floor. Do this on the drivers (left) and passenger (right) side. Remove the rubber plugs.

5. Enlarge the TOP of the drain hole to 1-1/4” (no need to enlarge the bottom part of the hole!). This can be
done with a round (rat-tail) file or a small grinding bit on a hi-speed grinder. It is very close to this size and not
much material needs to be removed. See Figure 3.

6. If you wish to retain the padding that was on the factory horizontal bars, cut about 4 inches from the front of
each piece and slide it over the Sport Cage side bars. Install the factory stubs into the L & R Sport Cage
bars. Using the factory #50 tamperproof Torx® head bolts, install the head on the inside, threads pointing
outward. Do not tighten yet, leave them snug only. See Figure 4.

7. Install the left Sport Cage bar in the drivers side of the Jeep®. There is a pre-welded stub on the bottom of
the floor plate that has threads in it. This stub inserts into the factory drain hole in the floor. Install the split­lock washer on the 9/16”X1-1/2” bolt, then install the large flat washer on the same bolt. See Figure 5. Start
the bolt into the threaded stub in the bottom of the floor plate. See Figure 6. Do not tighten at this time. In­stall the factory stub to the Jeep® roll bar with the factory # 40 Torx head bolts. See Figure 7. Do not tighten
at this time.

8. Install the cross bar on the pre-welded stub on the left side bar, (Use your rat-tail file to remove any burrs
from the inside of the crossbar). See Figure 8.

9. Install the right Sport Cage bar in the passenger side of the Jeep®. As you install it, insert the cross bar
over the pre-welded stub. See Figure 9. Follow the same procedure as in step 7.

10. Install the drivers side “L” bracket, and passenger side “L” bracket on the W/S frame using the factory #40
Torx head bolts. Snug tighten only.

11. Soft top installations: Install both door surrounds to the Sport Cage, W/S frame, and body tub. See Fig-
ure 10.

12. Close the doors against the surrounds. Make sure that they seal tight. You may have to push the Sport

Cage bars outward to help the doors seal against the surrounds. The pilot holes in the cross bar should be in
the center of the slot of the W/S brackets. If not, loosen the W/S bracket and move it until it lines up, and/or
rotate the cross bar. See Figure 11. With a 3/8” bit in a power drill, enlarge the pilot hole in the cross bar to
3/8”. Drill from the top downward first. Now drill the pre-welded stub to 3/8” (continue to push the side bars
against the door surrounds!). See Figure 12. Insert the 3/8”X2-1/4” bolt into the hole that you just drilled, to
hold all parts in place while you drill the bottom pilot hole and stub. See Figure 13. If you have a hard top,
and never plan on installing a factory style soft top, simply pull the two side bars together (crimping the cross
bar between them) and drill as described above.

13. Remove the bolt, and install it from the bottom with the threads pointing up, through the W/S bracket.

Install one flat washer and the 3/8” crimp-loc nut. Do not tighten at this time. See Figure 14.