Mountain Off Road JRB801 User Manual

MOUNTAIN OFF ROAD ENTERPRISES, Inc.

P O BOX 690, DELTA, CO 81416

970-625-0500 970-625-3747 Fax

E-mail: info@mountainoffroad.com

www.mountainoffroad.com

INSTALLATION INSTRUCTIONS FOR: JRB801

PLEASE READ AND UNDERSTAND TERMS / POLICIES BEFORE PROCEEDING

HARDWARE KIT: 4 – 7/16-14 x 4.5” bolts 10 – 7/16 Flat Washers 4 – 7/16 Lock Washers 3 – 7/16-14x1-1/4” bolts 3 – 7/16-14 crimp lock nuts

FIT and TOLERANCES: All parts i n M.O.R.E.™ products are the results of countless hours of research, testing, fitting and refining. Jeeps have a large tolerances from vehicle to vehicle. In addition to the factory tolerances, most people install other then factory equipment (aftermarket add-ons). M.O.R.E.™ has done the best job we can to insure that our parts fit with some of the possibilities. However, you may find it necessary to grind, elongate, bend, or force the parts you buy to fi t on your rig. Be sure that you want to install them before you modify them. Please use common sense when installing these parts and let us know how we can improve them.

DAMAGE CLAIMS: All orders are carefully packed, however, mishandling by the carrier can result in damage. The carrier has the responsibili ty for the shipment from the time it leaves our warehouse until it is delivered to you. All claims for lost or damaged goods should be reported to the carrier, not to M.O.R.E.™ LLC.

RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. Aft er you receive a Return Goods Authorization (RGA) number, merchandise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original invoice or a copy with the RGA nu mber written on must accompany al l returns. A 20% restocking fee will be charged on all parts returned for credit or refund unless merchandise is proven to be defective or was shipped wr ong by M.O.R.E.™ LLC. No merchandise will be issued credit or refund if it has been installed, modified, used in any way or is in unsalable condition.

WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper use will void this warranty. Because all parts we sell are intended for use in heavy-duty applications it i s not possible to warrantee or guarantee the performance of any items. M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite variety of conditions due to the manner in which they are used, serviced and/or installed. Purchasers and users of such products rely upon their own judgment as to the suitable use selection, service and installation of such products.

PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous condition which could cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All parts sold by M.O.R.E.™ LLC. are for racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for personal injury or property damage arising from the failure of any parts manufactured or sold by M.O.R.E.™ LLC.

Specifications are subject to change without notice.

Jeep®, AMC®, CJ®, YJ®, TJ®, JK® Wrangler®, are registered trademarks of DaimlerChrysler. M.O.R.E.™ is not affiliated with DaimlerChrysler.

PAGE 1 of 3

TERMS / POLICIES:

M.O.R.E.™ recommends pre-fitting this BUMPER into your Jeep® BEFORE you paint it. Make sure that you Have no fit issues with any Aftermarket accessories and that you are happy with all aspects of it. If you are, then paint it and re-install it. Once you modify it in any way, it is NON-RETURNABLE !!!

1– Remove Factory rear bumper & if equipped remove tow hitch and or tow hook. Save the 4 factory bolts that attached the bumper to the frame on the sides of the frame (see figure 1B) .

2– The JRB800 bumper will attach to the back crossmember with 4 bolts (see figures 1A & 1B) and to the 4 bolts removed earlier from the sides of the frame.

3– Install JRB800 rear bumper and install the 4 factory bolts back into the side

frame holes do not tighten at this time ( See Figure 2) . Install the 7/16x4.5”

bolts ,flat and lock washers through the backing plate and then through the rear crossmember of the Jeep (see figure 3). NOTE: It may be necessary to enlarge the

outside of the holes on the rear crossmemeber (see figure 4).Tighten the 4 7/16”

bolts in the center and then the 4 bolts on the sides of the frame.

Figure 1A Figure 1B

4– 7/16”x 4.5” bolts coming in from the back 2– Factory bolts per side of frame.

PAGE 2 of 3

+ 1 hidden pages