Mountain Off Road JRB600 User Manual

MOUNTAIN OFF ROAD ENTERPRISES, LLC

P O BOX 690, DELTA, CO 81416

(877)JEEP-A2Z or (877)533-7229

970-625-0500 970-625-3747 Fax

E-mail: info@mountainoffroad.com

www.mountainoffroad.com

INSTALLATION INSTRUCTIONS FOR: JRB600

PLEASE READ AND UNDERSTAND TERMS / POLICIES BEFORE PROCEEDING

Fits 84-01 JEEP XJ

License Plate Bracket SOLD SEPERATELY !

HARDWARE KIT:

1 – DS Mounting Bracket

1 – PS Mounting Bracket 1 – Lower Frame Crossmember Bracket 1 – Double Bear Claw Latch 4 - Allen head bolts 1 – Latch Mud Guard 1- Latch Release Lever 1– Latch Release Button 2- 1/4”x .75 bolts 2- 1/4” top loc nuts 1- 1/4” lock washer 1- Ramp Pad 1– Rubber Bumper 2– 1/4”x .375” Socket Head Cap Screw 2– 5/16”x.75 Flat Head Bolt 16– 1/2”x1.5” Bolts 16– 1/2” Flat Washer 16– 1/2” Lock Washer 3– 3/8”x1” Bolt, Nuts, Washers 1– stainless steel logo and screws 3– Wheel studs Bearings, Seal, Nut, Washer, Cotter Pin, Dust Cap

FIT and TOLERANCES: All parts i n M.O.R.E.™ products are the results of countless hours of research, testing, fitting and refining. Jeeps have a large tolerances from vehicle to vehicle. In addition to the factory tolerances, most people install other then factory equipment (aftermarket add-ons). M.O.R.E.™ has done the best job we can to insure that our parts fit with some of the possibilities. However, you may find it necessary to grind, elongate, bend, or force the parts you buy to fi t on your rig. Be sure that you want to install them before you modify them. Please use common sense when installing these parts and let us know how we can improve them.

DAMAGE CLAIMS: All orders are carefully packed, however, mishandling by the carrier can result in damage. The carrier has the responsibili ty for the shipment from the ti me it leaves our warehouse until it is delivered to you. All claims for lost or damaged goods should be reported to the carrier, not to M.O.R.E.™ LLC.

RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. After you receive a Return Goods Authorization (RGA) number, merchandise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original invoice or a copy with the RGA number written on must accompany all returns. A 20% restocking fee will be charged on all parts returned for credit or refund unless merchandise is proven to be defective or was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit or refund if it has been installed, modified, used in any way or is in unsalable condition.

WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper use will void this warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or guarantee the performance of any items. M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite variety of conditions due to the manner in which they are used, serviced and/or installed. Purchasers and users of such products rely upon their own judgment as to the suitable use selection, service and installation of such products.

PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous condition which could cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All parts sold by M.O.R.E.™ LLC. are for racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for personal injury or property damage arising from the failure of any parts manufactured or sold by M.O.R.E.™ LLC.

Specifications are subject to change without notice.

Jeep®, AMC®, CJ®, YJ®, TJ®, LJ® ,JK® ,XJ® ,Wrangler®, are registered trademarks of DaimlerChrysler. M.O.R.E.™ is not affiliated with DaimlerChrysler.

TERMS / POLICIES:

PAGE 1 of 6

M.O.R.E.™ recommends pre-fitting this BUMPER into your Jeep® BEFORE you paint it. Make sure that you Have no fit issues with any Aftermarket accessories and that you are happy with all aspects of it. If you are, then paint it and re-install it. Once you modify it in any way, it is NON-RETURNABLE !!!

1– Remove Factory rear bumper & if equipped remove tow hitch and or tow hook. Save the 8 factory bolts that attached the bumper to the rear of the unibody.

2– Attach latch release lever to bear claw latch using supplied 1/4”x .75 bolt and top loc nut . Attach spring through hole in latch release lever and latch body (see

figure 1A). Attach latch release button to latch release lever using a 1/4” x .75 bolt

and lock washer (see figure 1B).

3– Insert latch assembly into rear of bumper and attach using 4 supplied Allen head bolts (see figures 2 and 2A).

4– Insert DS and PS mounting brackets into unibody frame rails and attach loosely with factory bolts (see figures 3 and 3A) For 97 or newer jeeps you will have to notch the unibody (see figure3B).

5– Raise Frame crossmember bracket into place and attach through framerail into

DS and PS brackets using 1/2” x 1.5” bolts, flat washers, and lock washers ( see

figure 4). Do not crossthread bolts. Once all bolts are started, you may tighten all bolts .

6– Raise bumper and slide over mounting brackets. Start 1/2” x 1.5” bolts with flat and lock washers through bumper into PS mounting bracket (see figure 5).

7– Position latch mud cover and start 1/2” x 1.5” bolts with flat and lock washers through bumper into DS mounting bracket (see figure 6).

8- Start 1/2” x 1.5” bolts with flat and lock washers trough the bottom of the bumper into the frame crossmember bracket. Do not crossthread!!! (see figure 7)

PAGE 2 of 6

+ 4 hidden pages