MOTU 9335, 9330 User manual
24Ai
24Ao
User Guide
Title Page
™
™
1280 Massachusetts Avenue
Cambridge, MA 02138
Business voice: (617) 576-2760
Business fax: (617) 576-3609
Web site: www.motu.com
Tech support: www.motu.com/support
SAFETY PRECAUTIONS AND ELECTRICAL REQUIREMENTS FOR THE 24Ai, 24Ao and MOTU AVB SWITCH (“PRODUCT”)
CAUTION! READ THIS SAFETY GUIDE BEFORE YOU BEGIN INSTALLATION OR OPERATION. FAILURE TO COMPLY WITH SAFETY INSTRUCTIONS
COULD RESULT IN BODILY INJURY OR EQUIPMENT DAMAGE.
HAZARDOUS VOLAGES: CONTACT MAY CAUSE ELECTRIC SHOCK OR BURN. TURN OFF UNIT BEFORE SERVICING.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUGS WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THE MOTU PRODUCT COULD CAUSE AN ELECTRICAL SHOCK.
The MOTU product is equipped with a three-conductor cord and grounding type plug which has a grounding prong, approved by Underwriters' Laboratories and the Canadian Standards Association.
This plug requires a mating three-conductor grounded type outlet as shown in Figure A below. If the outlet you are planning to use for the MOTU product is of the two prong type, DO NOT REMOVE
OR ALTER THE GROUNDING PRONG IN ANY MANNER. Use an adapter as shown below and always connect the grounding lug to a known ground. It is recommended that you have a qualified
electrician replace the TWO prong outlet with a properly grounded THREE prong outlet. An adapter as illustrated below in Figure B is available for connecting plugs to two-prong receptacles.
Figure A Figure B
Grounding lug
Screw
3-prong plug
Grounding prong
Properly grounded 3-prong outlet
3-prong plug
Mak e sur e th is i s con nec ted to
a known ground.
Adapter
Two-prong receptacle
WARNING: THE GREEN GROUNDING LUG EXTENDING FROM THE ADAPTER MUST BE CONNECTED TO A PERMANENT GROUND SUCH AS TO A
PROPERLY GROUNDED OUTLET BOX. NOT ALL OUTLET BOXES ARE PROPERLY GROUNDED.
If you are not sure that your outlet box is properly grounded, have it checked by a qualified electrician. NOTE: The adapter illustrated is for use only if you already have a properly grounded two-prong
receptacle. Adapter is not allowed in Canada by the Canadian Electrical Code. Use only three wire extension cords which have three-prong grounding type plugs and three-prong receptacles which
will accept the MOTU product plug.
IMPORTANT SAFEGUARDS
1. Read these instructions. All the safety and operating instructions should be read before operating the product.
2. Keep these instructions. These safety instructions and the product owner’s manual should be retained for future reference.
3. Heed all warnings. All warnings on the product and in the owner’s manual should be adhered to.
4. Follow all Instructions. All operating and use instructions should be followed.
5. Do not use the product near water.
6. Cleaning - Unplug the product from the computer and clean only with a dry cloth. Do not use liquid or aerosol cleaners.
7. Ventilation - Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Heat - Do not install the product near any heat sources such as radiators, heat registers, stoves, or another apparatus (including an amplifier) that produces heat.
9. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electrical shock.
10. Grounding - Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult and electrician for replacement of the obsolete outlet.
11. Power cord - Protect the product power cord from being walked on or pinched by items placed upon or against them. Pay particular attention to cords and plugs, convenience receptacles, and the point where they exit from the unit.
12. Power switch - Install the product so that the power switch can be accessed and operated at all times.
13. Disconnect - The main plug is considered to be the disconnect device for the product and shall remain readily operable.
14. Accessories - Only use attachments/accessories specified by the manufacturer.
15. Placement - Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the product. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
16. Surge protection - Unplug the product during lightning storms or when unused for long periods of time.
17. Servicing - Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as when a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped.
18. Power Sources - Refer to the manufacturer’s operating instructions for power requirements. Be advised that different operating voltages may require the use of a different line cord and/or attachment plug.
19. Installation - Do not install the product in an unventilated rack, or directly above heat-producing equipment such as power amplifiers. Observe the maximum ambient operating temperature listed below.
20. Power amplifiers- Never attach audio power amplifier outputs directly to any of the unit’s connectors.
21. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
22. Safety Check - Upon completion of any service or repairs to this MOTU product, ask the service technician to perform safety checks to determine that the product is in safe operating conditions.
ENVIRONMENT, HEAT AND VENTILATION
Operating Temperature: 10°C to 40°C (50°F to 104°). The product should be situated away from heat sources or other equipment that produces heat. When installing the product in a rack or any other location, be sure there is adequate
space around the product to ensure proper ventilation. Improper ventilation will cause overheating and can damage the unit.
TO REDUCE THE RISK OF ELECTRICAL SHOCK OR FIRE
Do not handle the power cord with wet hands. Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.
Do not expose this apparatus to rain or moisture. Do not place objects containing liquids on it.
AC INPUT
100 - 240VAC ~ • 50 / 60Hz • 0.5A max
Contents
Part 1: Getting Started
7
Quick Start Guide
24Ai Front Panel
9
10
24Ai Rear Panel
24Ao Front Panel
11
24Ao Rear Panel
12
13
MOTU AVB Switch
MOTU AVB Control Web App
15
25
About Your MOTU AVB Audio Interface
Packing List and System Requirements
29
31
Software Installation
Hardware Installation
33
Part 2: Using your MOTU interface
Presets
45
51
The Front Panel LCD
Working with Host Audio Software
53
Mixer Effects
61
Networking
67
Part 3: Appendices
Troubleshooting
75
77
Audio Specifications
Mixer Schematics
79
83
D-sub Connector Specifications
Updating Firmware
85
OSC Support
87
89
Index
III
About the Mark of the Unicorn License Agreement and
Limited Warranty on Software
TO PERSONS WHO PURCHASE OR USE THIS PRODUCT: carefully read all the
terms and conditions of the “click-wrap” license agreement presented to you when
you install the software. Using the software or this documentation indicates your
acceptance of the terms and conditions of that license agreement.
Mark of the Unicorn, Inc. (“MOTU”) owns both this program and its documentation.
Both the program and the documentation are protected under applicable copyright,
trademark, and trade-secret laws. Your right to use the program and the
documentation are limited to the terms and conditions described in the license
agreement.
Reminder of the terms of your license
This summary is not your license agreement, just a reminder of its terms. The actual
license can be read and printed by running the installation program for the software.
That license agreement is a contract, and clicking “Accept” binds you and MOTU to
all its terms and conditions. In the event anything contained in this summary is
incomplete or in conflict with the actual click-wrap license agreement, the terms of the
click-wrap agreement prevail.
YOU MAY: (a) use the enclosed program on a single computer; (b) physically transfer
the program from one computer to another provided that the program is used on only
one computer at a time and that you remove any copies of the program from the
computer from which the program is being transferred; (c) make copies of the
program solely for backup purposes. You must reproduce and include the copyright
notice on a label on any backup copy.
YOU MAY NOT: (a) distribute copies of the program or the documentation to others;
(b) rent, lease or grant sublicenses or other rights to the program; (c) provide use of
the program in a computer service business, network, time-sharing, multiple CPU or
multiple user arrangement without the prior written consent of MOTU; (d) translate,
adapt, reverse engineer, decompile, disassemble, or otherwise alter the program or
related documentation without the prior written consent of MOTU.
MOTU warrants to the original licensee that the disk(s) on which the program is
recorded be free from defects in materials and workmanship under normal use for a
period of ninety (90) days from the date of purchase as evidenced by a copy of your
receipt. If failure of the disk has resulted from accident, abuse or misapplication of the
product, then MOTU shall have no responsibility to replace the disk(s) under this
Limited Warranty.
THIS LIMITED WARRANTY AND RIGHT OF REPLACEMENT IS IN LIEU OF,
AND YOU HEREBY WAIVE, ANY AND ALL OTHER WARRANTIES, BOTH
EXPRESS AND IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
LIABILITY OF MOTU PURSUANT TO THIS LIMITED WARRANTY SHALL BE
LIMITED TO THE REPLACEMENT OF THE DEFECTIVE DISK(S), AND IN NO
EVENT SHALL MOTU OR ITS SUPPLIERS, LICENSORS, OR AFFILIATES BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LOSS OF USE, LOSS OF PROFITS, LOSS OF DATA OR
DATA BEING RENDERED INACCURATE, OR LOSSES SUSTAINED BY THIRD
PARTIES EVEN IF MOTU HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW
THE LIMITATION OR EXCLUSION OF LIABILITY FOR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Update Policy
In order to be eligible to obtain updates of the program, you must complete and return
the attached Mark of the Unicorn Purchaser Registration Card to MOTU.
Copyright Notice
Copyright © 2014 by Mark of the Unicorn, Inc. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any human or computer language, in any form or by any means
whatsoever, without express written permission of Mark of the Unicorn, Inc., 1280
Massachusetts Avenue, Cambridge, MA, 02138, U.S.A.
Limited Warranty on Hardware
Mark of the Unicorn, Inc. and S&S Research (“MOTU/S&S”) warrant this equipment
against defects in materials and workmanship for a period of TWO (2) YEARS from
the date of original retail purchase. This warranty applies only to hardware products;
MOTU software is licensed and warranted pursuant to separate written statements.
If you discover a defect, first write or call Mark of the Unicorn at (617) 576-2760 to
obtain a Return Merchandise Authorization Number. No service will be performed on
any product returned without prior authorization. MOTU will, at its option, repair or
replace the product at no charge to you, provided you return it during the warranty
period, with transportation charges prepaid, to Mark of the Unicorn, Inc., 1280
Massachusetts Avenue, MA 02138. You must use the product’s original packing
material for in shipment, and insure the shipment for the value of the product. Please
include your name, address, telephone number, a description of the problem, and
the original, dated bill of sale with the returned unit and print the Return Merchandise
Authorization Number on the outside of the box below the shipping address.
This warranty does not apply if the equipment has been damaged by accident,
abuse, misuse, or misapplication; has been modified without the written permission
of MOTU, or if the product serial number has been removed or defaced.
ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO TWO (2) YEARS FROM THE DATE OF THE
ORIGINAL RETAIL PURCHASE OF THIS PRODUCT.
THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE
AND IN LIEU OF ALL OTHERS, ORAL OR WRITTEN, EXPRESS OR IMPLIED.
No MOTU/S&S dealer, agent, or employee is authorized to make any modification,
extension, or addition to this warranty.
MOTU/S&S ARE NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF
WARRANTY, OR UNDER ANY LEGAL THEORY, INCLUDING LOST PROFITS,
DOWNTIME, GOODWILL, DAMAGE OR REPLACEMENT OF EQUIPMENT
AND PROPERTY AND COST OF RECOVERING REPROGRAMMING, OR
REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH
MOTU/S&S PRODUCTS.
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may have other
rights which vary from state to state.
MOTU, Digital Performer, AudioDesk, Mark of the Unicorn and the unicorn silhouette
logo are trademarks of Mark of the Unicorn, Inc.
Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation in the U.S.
and/or other countries.
This equipment has been type tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio
or television equipment reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by any combination of the following measures:
• Relocate or reorient the receiving antenna
• Increase the separation between the equipment and the receiver
• Plug the equipment into an outlet on a circuit different from that to which the receiver is connected
If necessary, you can consult a dealer or experienced radio/television technician for additional
assistance.
PLEASE NOTE: only equipment certified to comply with Class B (computer input/output devices,
terminals, printers, etc.) should be attached to this equipment, and it must have shielded interface
cables in order to comply with the Class B FCC limits on RF emissions.
WARNING: changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Part 1
Getting Started
Quick Start Guide
CHAPTER
Thank you for purchasing a MOTU AVB interface!
Follow these easy steps to get started quickly.
1
Download and run the
MOTU AVB Installer
:
http://www.motu.com/avb
2
(Optional) For quick access to your MOTU
interface from your iPad or iPhone, download the
MOTU AVB Discovery app from the Apple App
Store.
Your iPhone and iPad must be on the same
☛
WiFi network as your computer.
3
Connect the interface to your computer with a
USB cable (included).
4
Switch on your MOTU interface.
5
Open the
MOTU AVB Control
web app by doing
one of the following:
■
From your computer, choose your MOTU
interface from the MOTU AVB Discovery app
menu, as shown below.
MOTU AVB Discovery app menu
For advanced network options, and device
■
discovery from any modern browser, see chapter 9,
“Networking” (page 67).
6
Choose a preset from the Quick Setup.
Preset Application
Audio interface Operate as a standard audio interface.
Stand-alone mixer Operate as a stand-alone mixer, where all
Interface + mixer A combination of the above two presets.
Live recording with
monitor mixing
Stage I/O Route audio inputs from one AVB interface
inputs are mixed to the main outs and monitor outs.
Record a live concert or recording session,
with a full monitor mix.
to another, through Ethernet cabling.
■
From your iPad or iPhone, launch the MOTU
AVB Discovery app, and tap your interface.
■
You should now see the
MOTU AVB Control
web
app in your browser, as shown on page 16. If not,
visit Appendix A, “Troubleshooting” (page 75).
Studio Input
Expander
Studio Output
Expander
Optical Converter Multi-channel analog-to-digital or digital-
Routes the expansion unit’s physical inputs
to the main system using AVB network
streams.
Routes the main systems’s AVB network
streams to physical outputs on the expansion unit.
to-analog converter.
7
8
321 4
ARROW buttons to scroll through menu options. Push
again to descend into the submenus, if applicable. To
choose the current setting, push SELECT a third time.
Push BACK to return to the previous menu level, and do
so repeatedly to exit the menu altogether.
5. Push SEL (select) to enter the LCD menu. Push the
56
including its IP address.
6. Push ID to display network settings for the device,
24Ai Front Panel
rate and clock mode (source) for the unit.
3. The CLOCK section displays the current operating sample
4. POWER SWITCH: AVB and USB are “plug-and-play” proto-
inputs.
1. ANALOG INPUT METERS for the twenty-four analog
2. ADAT OPTICAL input and output metering. At 1x sample
cols. That means you can turn the 24Ai off and back on
without restarting your computer.
rates (44.1 or 48 kHz), there are twenty-four channels of
input and output. At 2x (88.2 or 96 kHz), there are twelve
channels.
24Ai Rear Panel
9
threading (not metric threading).
7. Use a standard (AES-59) Panasonic/Tascam DB-25 cable.
8. Make sure the retaining screws have standard 4-40
9. These are the pin-outs for the D-sub connector.
4
Another 24Ai or any other MOTU AVB-equipped device,
such as the 1248, 8M, 16A or 24Ao audio interfaces. ■A standard Ethernet hub or WiFi router (for internet
connection and communication with the MOTU AVB
Control web app software).■A standard AVB Ethernet switch for high-speed, low-
latency, high-capacity audio connectivity to an AVB
802.1 network connectivity to other network devices.
Examples include:
6. The AVB Ethernet port provides industry standard IEEE
■
audio network.
5
balanced analog input. You can use either a standard
8-channel Panasonic/Tascam format DB-25 cable or the
two 4-channel Phoenix connectors. DO NOT connect
both the D-sub and Phoenix connectors for a bank at the
same time. You can, however, use different connectors
across banks, if needed (for example, D-sub for channels
1-8 and Phoenix for channels 9-16). The pin-outs for the
Phoenix connectors are indicated on the label of the
connector; for the D-sub pinouts, see Appendix D, “D-sub
Connector Specifications” page (83).
using a standard USB cable. You can connect it to a
6
7
8
4. These three 8-channel banks provide 24 channels of
USB 2.0 or 3.0 port on the computer.
5. Connect the 24Ai to the computer with this USB 2.0 port
1 2 3
tional power supply.
tions, such as digital transfers with devices that cannot
slave to the clock supplied by their digital I/O connection
with the 24Ai.
channels of 24-bit ADAT optical digital I/O at 1x sample
rates (44.1 or 48 kHz) and 12 channels at 2x sample rates
(88.2 or 96 kHz). They are disabled at higher sample
rates. The IN and OUT ports on the right provide channels
1-8 (or 1-4), the left-hand ports provide channels 9-16
(or 5-8), and the third bank below provides channels
1. The 24Ai is equipped with an auto-switching interna-
2. BNC word clock jacks. Use them for a variety of applica-
3. These three ADAT optical “lightpipe” jacks provide 24
17-24 (or 9-12).
24Ao Front Panel
321 4
ARROW buttons to scroll through menu options. Push
again to descend into the submenus, if applicable. To
choose the current setting, push SELECT a third time.
Push BACK to return to the previous menu level, and do
so repeatedly to exit the menu altogether.
5. Push SEL (select) to enter the LCD menu. Push the
56
rate and clock mode (source) for the unit.
cols. That means you can turn the 24Ao off and back on
3. The CLOCK section displays the current operating sample
4. POWER SWITCH: AVB and USB are “plug-and-play” proto-
including its IP address.
6. Push ID to display network settings for the device,
without restarting your computer.
outputs.
1. ANALOG OUTPUT METERS for the twenty-four analog
2. ADAT OPTICAL input and output metering. At 1x sample
rates (44.1 or 48 kHz), there are twenty-four channels of
input and output. At 2x (88.2 or 96 kHz), there are twelve
channels.
24Ao Rear Panel
9
threading (not metric threading).
7. Use a standard (AES-59) Panasonic/Tascam DB-25 cable.
8. Make sure the retaining screws have standard 4-40
9. These are the pin-outs for the D-sub connector.
4
Another 24Ao or any other MOTU AVB-equipped device,
such as the 1248, 8M, 16A or 24Ai audio interfaces. ■A standard Ethernet hub or WiFi router (for internet
connection and communication with the MOTU AVB
Control web app software).■A standard AVB Ethernet switch for high-speed, low-
latency, high-capacity audio connectivity to an AVB
802.1 network connectivity to other network devices.
Examples include:
6. The AVB Ethernet port provides industry standard IEEE
■
audio network.
5
balanced analog output. You can use either a standard
8-channel Panasonic/Tascam format DB-25 cable or the
two 4-channel Phoenix connectors. DO NOT connect both
the D-sub and Phoenix connectors for a bank at the same
time. You can, however, use different connectors across
banks, if needed (for example, D-sub for channels 1-8
and Phoenix for channels 9-16). The pin-outs for the
Phoenix connectors are indicated on the label of the
connector; for the D-sub pinouts, see Appendix D, “D-sub
Connector Specifications” page (83).
using a standard USB cable. You can connect it to a
6
7
8
4. These three 8-channel banks provide 24 channels of
USB 2.0 or 3.0 port on the computer.
5. Connect the 24Ao to the computer with this USB 2.0 port
1 2 3
tional power supply.
tions, such as digital transfers with devices that cannot
slave to the clock supplied by their digital I/O connection
with the 24Ao.
channels of 24-bit ADAT optical digital I/O at 1x sample
rates (44.1 or 48 kHz) and 12 channels at 2x sample rates
(88.2 or 96 kHz). They are disabled at higher sample
rates. The IN and OUT ports on the right provide channels
1-8 (or 1-4), the left-hand ports provide channels 9-16
(or 5-8), and the third bank below provides channels
1. The 24Ao is equipped with an auto-switching interna-
2. BNC word clock jacks. Use them for a variety of applica-
3. These three ADAT optical “lightpipe” jacks provide 24
17-24 (or 9-12).
MOTU AVB Switch
MOTU AVB interfaces (1248, 8M, 16A, 24Ai, 24Ao)
Another MOTU AVB Switch (to extend the network)
A 3rd-party AVB switch
An Ethernet device, Wi-Fi router or Ethernet network
A third-party AVB device
device, Wi-Fi router or Ethernet network. DO NOT connect AVB devices to this port; it does
not support AVB.
supply that conforms to the indicated specifications.
■
■
■
■
1. Use these 1 gigabit AVB NETWORK ports to connect any of the following:
■
2. This standard Ethernet port can be used to connect a standard 10/100/1Gb Ethernet
connected to a port , the 1 Gb LED illuminates.
3. Connect the included 15V DC power supply here. Alternately, you can use any power
4. The front panel LEDs indicate signal activity for each port. When a 1 gigabit device is
NOTE: When making network connections, use shielded CAT-5e or CAT-6 cables (a higher
grade cable). For local connections, patch cables can be used, but will reduce the maximum
total cable run length.
No configuration is necessary. The switch configures itself and manages all device
discovery, configuration, and system resource allocation.
The switch establishes and maintains extremely accurate timing and synchronization
among all connected devices.
The switch negotiates audio routing throughout the network and guarantees that audio
integrity is maintained, regardless of external (non AVB) network traffic.
■
The MOTU AVB Switch provides deep functionality that goes beyond
a standard Ethernet switch.
■
The switch consolidates audio, synchronization, and control together.
■
■
For more information, see chapter 9, “Networking” (page 67).
21 3
4
14
MOTU AVB Control Web App
CHAPTER
OVERVIEW
MOTU AVB Control is a web app that gives you
comp lete cont rol over your MOTU aud io inter face.
If you have several MOTU AVB interfaces
networked together, such as the 24Ai and 24Ao,
you can control them all. If you are working with a
large-scale network of many MOTU AVB
interfaces, you can access and control any device
on the network.
IT’S NOT ON YOUR HARD DRIVE
The MOTU AVB Control web app is served from
the audio interface hardware itself, therefore it is
not an application on your computer’s hard drive.
Instead, access it by using the MOTU AVB
Discovery Application, or through your web
browser by t yping your MOTU device’s IP Address
into the address bar.
USE YOUR FAVORITE WEB BROWSER
The MOTU AVB Control web app runs in any
modern web browser on any device connected to
your MOTU interface, either directly or wirelessly
through a WiFi network. You can use any device
you w ish: a desktop computer, laptop, iPad, tablet,
iPhone or smar t phone. If it can r un a web browser,
it can run the web app. You can use any browser
you prefer: Chrome, Firefox, Safari, IE 11 etc. The
latest versions are strongly recommended.
CONTROL FROM MULTIPLE DEVICES
You can run the web app on multiple host devices
simultaneously.
RUN THE INSTALLER, GET THE APP
Visit www.motu.com/avb to get the latest MOTU
AVB installer and run it on your computer to install
MOTU AVB Discovery app and drivers. Visit the
the
Apple App Store to download the discovery app
onto your iPad or iPhone.
MAKE HARDWARE AND NETWORK CONNECTIONS
Connect your MOTU interface to your computer
or laptop with a USB cable. Make sure your iPad,
iPhone, tablet or smartphone is connected to the
same WiFi network as your computer or device.
You can use any network connection scenario
explained in “Setup for web app control” on
page 38.
LAUNCHING THE WEB APP
To launch the web app, do any of the following:
■
From your computer, choose your MOTU
interface from the MOTU AVB Discovery app
menu, as shown below. If you have multiple
interfaces, choose the one you want.
■
From your iPad or iPhone, launch the MOTU
AVB Discovery app.
■
From any web browser on any host (computer,
tablet, etc.), type in the IP address or .localname of
your MOTU AVB interface. See below for how to
obtain the IP address.
You should now see the MOTU AVB Control web
app in your browser, as shown on page 16. If not
visit Appendix A, “Troubleshooting” page (75).
Obtaining your MOTU device’s IP address
On the front panel of the interface, push the ID
knob or button once. The LCD now displays the
unit’s I P add ress , which sh ould lo ok some thing like
“IP Address: 192.168.1.209”.
this:
15
DEVICE TAB
6
7
8
5
4
9
10
11
12
3
2
13
1
14
15
16
17
1. If you have two or more MOTU AVB
interfaces, the Device list lets you
choose the one you are currently
controlling with the web app.
2. The Aux Mixing tab lets you view
each Aux bus in the mixer, one at a
time.
3. The Mixing tab gives you access to
the mixing and DSP in the interface.
4. The Routing tab displays a grid
matrix, where you can make direct
connections between inputs and
outputs, your computer, the mixer,
and network audio streams, if
networked interfaces are connected.
5. The Device tab has settings for the
hardware itself, such as mic input
phantom power and preamp gain.
16
6. Expands and collapses the sidebar.
7. Lets you create, save, recall and
manage presets for your MOTU AVB
interface. These presets capture and
recall the complete state of the
device (all settings in all tabs).
8. Choose the desired sample rate.
9. The Quick Setup button prompts
factory presets used to configure
your interface for a specific application. See chapter 5, “Presets”
(page 45).
10. Click to rename the interface. To
restore the default name, delete the
current name.
11. Click this device ID button to identify
the unit you are currently viewing
and controlling with the web app
software. The front panel LCD on the
hardware itself will flash the name
of the device, and its name will also
flash in the Device list (1).
12. If an update is available for your
device, and the computer you are
viewing it from is connected to the
internet, you’ll be notified here. Click
More Info to learn what’s new and
start the update process.
13. Choose the clock source from the
Clock Mode menu. Your MOTU device
will resolve its digital clock to this
master source. See “Synchronization” on page 40.
14. Indicates that the current device (1)
is successfully resolved to its chosen
Clock Mode source (13). If it cannot
MOTU AVB CONTROL WEB APP
lock for some reason, this icon
flashes red. Check your chosen clock
so urc e, ca bl es, e tc.
15. If you have multiple MOTU AVB
interfaces, one of them may serve as
a master clock source for the
network. Click this button to choose
the current interface (1) as the
master clock source.
16. These are the Output Settings for
the 24Ao, which provide 32 bit trim
in the DACs from zero to -24 dB.
17. These are the Input Settings for the
24Ai, which provide digitally
controlled analog trim from -96 to
+22 dB.
DEVICE TAB (CONTINUED)
19
20
18
24
23
21
22
Scroll down to view these additional
Device tab settings.
18. In the Input/Output Banks sec tions,
you can disable any banks that you
are not using. Doing so hides them
from the routing matrix and mixer to
simplify operation. Doing so also
helps conserve DSP resources.
AVB is IEEE’s Audio Video Bridging
19.
Ethernet standard for highbandwidth, low-latency audio
streaming over Ethernet. If your
24Ai or 24Ao is connected to a 2nd
MOTU AVB interface through its
network port, or to an AVB switch for
MOTU AVB CONTROL WEB APP
access to an extended AVB network,
you can stream audio channels to
other destinations on the network.
AVB streams are handled in banks of
eight channels, so if you enable 8
out of 8 streams, that’s 64 channels.
See chapter 9, “Net working”
(page 67).
20. If you have AVB network input
streams enabled, connect them to
the output streams of other devices
on the network here.
21. In the Computer Setup section, you
can specify how many audio
channels you would like to be able to
stream to and from your computer,
up to 24 channels each way, simultaneously. Map them as desired in
the Routing tab (page 18).
22. Use these buttons to manually check
for and install updates for your
MOTU AVB device. For complete
details, see Appendix E, “Updating
Firmware” page (85). Updating from
a file can be done offline from your
computer, using an update you’ve
obtained through MOTU’s web site
or tech support department. The
Check For Updates button requires
that the computer (or device) you
are using to view your MOTU AVB
interface is connected to the internet through a local network or WiFi.
Updating from the internet is easy
and convenient.
23. Use these buttons to reboot (restart)
the device, or restore its factory
presets.
24. The digital mixer in your MOTU AVB
interface supports up to 48
channels. If you don’t need that
many inputs, you can lower the
number here to simplify mixer and
routing operation and conserve DSP
bandwidth for effects processing.
17
ROUTING TAB
3
2
1
20
19
18
17
16
The Routing Tab lets you route inputs to
outputs. Outputs are listed by row on the
left; inputs are listed in columns across
the top. Simply click in the grid to make
a single connection. Click and drag to
make multiple connections in one
gesture. To route a single input to multiple outputs, make multiple connections
vertically in the same column below the
input. To mix multiple inputs to the
same output, you’ll need to use the
mixer (page 19) and the
the routing tab (16).
1. In its collapsed form, (shown here),
the sidebar displays icons for each
tab.
2. Click this icon to view the Routing
tab, shown on this page.
3. Click here to show or hide the
sidebar.
4. Create, save, recall and manage
routing presets.
5. Outputs are listed in rows on the left.
18
Mix In bank in
54 7
6
6. When you make a connection, the
source (input) signal is listed by
name here in the Source column,
just to the right of the output it is
being routed to.
7. Inputs are listed in columns across
the top of the grid, starting with the
physical inputs on the hardware
itself. In this example, each
8-channel ADAT optical bank is
collapsed. In the grid below, in the
first column, you can see that Bank A
input is routed to the computer.
From Computer input bank lets
8. The
you route audio channels from your
host audio software to any output,
including AVB network streams or
the mixer. In this example, all 24
computer output channels are
routed to the 24Ao analog outs. Use
the Device tab to choose how many
computer channels are available.
9. AVB streams are 8-channel banks
that let you route audio to or from
other devices on the AVB network (if
any are connected) to local
hardware inputs and outputs. Use
8 9
10
11
12
13
14
15
the Device tab (page 17) to configure how many AVB streams you wish
to work with. If you aren’t working
with network audio, you can set the
number of streams to zero (0).
10. These input streams are busses that
originate from the mixer, which
supplies the main mix bus, monitor
mix bus, seven stereo aux busses,
three stereo group busses, a reverb
return bus and postFX channel sends
(for sending processed inputs to the
computer or elsewhere). You can
route these mixer busses to any
outputs you wish (5), including
physical outputs, host software on
your computer, other devices on the
AVB network, or even back in to the
mixer (beware of feedback loops!)
11. Use these triangles to expand or
collapse groups of inputs. For
example, it might be convenient to
collapse banks that you are not
using at the moment.
12. Click a channel label to rename it.
13. Audio activit y indicators.
MOTU AVB CONTROL WEB APP
14. Click the grid to make a connection.
Click a connection to remove it. Click
and drag to make or break multiple
connections in one gesture.
15. In this example, all 24 channels from
the computer are routed to the 24
analog outputs on the 24Ao. In
addition, all 24 computer channels
are simultaneously being routed to
the three ADAT banks, for 24
channels of digital output.
Mix In group lets you route audio
16. The
to the 48-channel mixer.
17. These AVB output streams let you
route any audio to other devices on
the AVB network.
To Computer output bank routes
18. The
any input to host audio software
running on your computer. Use the
Device tab to choose how many
computer channels are available.
19. Use these triangles to expand or
collapse groups of outputs.
20. These are the physical outputs on
the interface itself.
MIXING TAB
4 5
6
7
93 13 14
8 10 11 12
15
16
2
1
30
29
28
27
26
25
The Mixing tab gives you full access to
the 48-channel mixer in your MOTU AVB
interface, which provides a main mix
bus, monitor bus, three group busses,
seven aux busses, and a dedicated
reverb bus. Use the Device tab to configure how many inputs you wish to work
with (up to 48). Use the Routing tab
(page 18) to route channels to the mixer
inputs. Channels can come from any
source, such as the physical inputs on
the interface, channels coming from the
computer, or channels coming from the
AVB net work .
1. Shows and hides the Mixer Setup
sidebar (3), which lets you show and
hide channels, channel strip
settings, effects, and the Legend (6).
2. The Mixing tab selects the mixer.
3. Use the Mixer Setup sidebar to show
and hide elements in the mixer.
4. Shows and hides all elements in the
section with one click.
5. Create, save, recall and manage
mixer presets.
SC
6. This column is the Legend. It
provides labels and controls for
channel strip sections. The menu at
the top lets you create, name, save
and manage entire mixer presets.
7. Mixer input channels.
8. This input channel has its Gate and
Compressor enabled. Disabled
effects are grayed out.
9. This is Group bus 1-2. You can send
inputs to this group with their Group
send fader (24). Groups are sent to
the Main Mix with its Main send
fader (24) or aux busses (19).
10. Group buses, the main mix bus, and
the reverb return bus are equipped
with the Leveler, a vintage compressor modeled after the Teletronix
LA-2A leveling amplifier.
11. The reverb channel strip provides
controls for the reverb processor. Use
the reverb send on individual inputs
or groups to route them to the
reverb bus, which can then be mixed
in with the main mix or aux busses.
Disable the reverb processor to use it
as an extra group.
12. The Monitor Bus can mirror the
output of any other bus, or it can act
as a separate Solo bus. See page 24.
13. The Main Mix bus is the master fader
for the entire mixer. You can add EQ
and Leveler compression.
14. You can adjust Aux bus output levels
here, or in the Aux Mixing tab shown
on page 20.
15. Click a name to change it, except for
the Main Mix, Monitor, and Reverb
busses, which cannot be changed.
16. Stereo toggle to switch channels
pairs between mono or stereo. Use
the other menus to manage channel
strip presets and to choose audio
sources and destinations for mixer
inputs and bus outputs.
17. Gate processing for inputs.
18. The Dynamics sec tion provides a
conventional compressor for inputs
and the Leveler for output busses.
17
18
19
20
21
22
23
24
19. Reverb and aux sends.
20. Solo and mute. On the Monitor bus,
button clears all solos.
the
21. Channel faders.
22. Choose the source for the Monitor
bus from this menu. It can mirror
any output bus or the Solo Bus.
Follow Solo is enabled, the
23. When
Monitor bus temporarily switches to
the solo bus when any channel is
soloed.
24. Group sends.
25. ‘S’ lets you solo the group. ‘PRE’
toggles the sends between pre- and
post-fader routing, i.e. before or
after the channel fader.
26. Show and hide output busses here.
27. Show/hide all busses with one click.
28. S ame as (24) above.
29. Show and hide inputs here.
30. Show/hide all inputs with one click.
MOTU AVB CONTROL WEB APP
19
AUX MIXING TAB
2
1
16
4
53
6
8
7
9
10
15
14
13
The Aux Mixing tab provides quick
access to your MOTU AVB interface’s mix
busses (aux busses, groups and reverb
bus), viewed one at a time. Choose a bus
in the Aux Mix Target section and then
use the faders to directly mix the send
levels from all mixer inputs, groups, and
the reverb bus.
1. Shows and hides the Mixer Setup
sidebar (3), which lets you show and
hide channels.
2. The Aux Mixing tab (shown on this
page) gives you access to the Aux
busses and groups in the mixer.
Aux Mix Target sidebar to
3. Use the
control which aux bus or group you
are currently viewing. You can also
show/hide inputs and group sends.
4. Click the aux bus or group you wish
to view in the window. In this
example, Aux bus 1-2 is being
displayed.
5. These are mixer inputs (aux sends
from each mixer channel). To include
an input in the aux bus mix, simply
bring up its fader.
6. These are group bus faders.
7. This is the mixer’s reverb bus fader.
8. This is the master fader for the
current aux bus being viewed (4).
9. Indicates if the input or group is
stereo or mono. Each channel’s
mono/stereo status cannot be
toggled (unlike MIXING page).
10. Solo and mute for the aux bus
master fader.
Prefader is enabled, all send
11. When
levels to the aux bus are independent of the main fader for each
channel. In other words, changing
an individual channel’s main fader in
the Mixing tab won’t affect its send
level to the aux bus.
11
12
12. Click the View Personal Mix button
to open a new web page that
displays only that specific Aux Mix or
Group.
13. Show and hide mix groups and the
reverb bus here.
14. Use the Groups button here to show
or hide all groups with one click.
15. Show and hide mixer inputs
(channel sends) here.
16. Show and hide all mixer inputs with
one click here.
20
MOTU AVB CONTROL WEB APP
MIXER INPUT CHANNEL STRIPS
1
2 3 4 5
26
6
7
25
3
8
9
10
4
11
12
13
24
23
14
15
16
17
18
19
20
22
21
To access a mixer input channel strip, go
to the Mixing tab (page 19), reveal the
side bar (item #3 on page 19), and then
show the input channel you want in the
Mixer Inputs section (29).
To show and hide sections of the channel
strip, such as EQ or the compressor, use
Contro ls section of the side bar (item
the
#3 in the mixer tab on page 19).
1. Click the input channel name to
change it. Delete the current name to
restore the default name.
2. Provides hardware settings for
inputs, if any, on other MOTU AVB
interfaces. In the case of the 24Ai and
24Ao, this is grayed out because there
are no hardware settings for inputs.
3. Choose the source for the input
channel. You can also make this
setting directly on the Routing grid
(page 18).
4. Create, name, save and recall channel
strip presets.
5. Toggles the input between mono and
a stereo pair.
∞
∞
6. High Pass Filter with cutoff frequency.
7. Each effect in the channel strip (High
Pass Filter, Gate, EQ, etc.) has an on/
off button (on the left) and a preset
menu on the right, for managing
presets that apply only to that
processing module. For example, you
can create your own EQ presets for the
EQ modules.
8. The Gate processor provides standard
attack, threshold and release
controls.
9. The Gate indicator turns red when the
gate is engaged.
10. The EQ section provides four bands of
parametric EQ, each with standard
Gain, Frequency, and Bandwidth
settings.
11. The High and Low EQ bands provide a
Shelf filter button for standard high
and low shelf filtering.
12. The Compressor provides standard
controls for Threshold, Ratio, Attack,
Release and Gain. Normally, the
compressor operates in Peak mode,
where signal peaks determine the
input level. Engage the RMS button to
uses RMS values (a computational
method for determining overall
loudness) to measure the input level.
13. Input level and gain reduction meters
for the compressor.
14. Aux and reverb sends.
15. Solo/Mute. Mute affects all sends as
well as the main channel. Pre-fader
sends are not affected by Mute.
16. Move the fader to adjust level.
Double-click to return to zero (unity
.
gain) or -
17. Click the dB scale numbers to make
the fader jump exactly to that level.
Click and drag horizontally to jump
consecutive faders to the same level.
18. Click to type in an exact dB level.
19. Channel pan. For mono inputs,
double-click to center.
20. Main Mix Slider is used to feed signal
to the Main Mix. Slider is set to 0 dB
by default, so all channel strips are
pre-routed to the Main Mix bus. If a
channel is being sent to a Group
(which will eventually be fed to the
Main Mix), drag the slider to is not sent to Main Mix directly.
21. Group sends.
22. ‘S’ lets you solo the group. ‘PRE’
toggles the sends between pre- and
post-fader routing, i.e. before or after
the channel fader.
23. Clears all solos.
24. ‘S’ lets you solo the Aux bus. ‘PRE’
toggles the sends between pre- and
post-fader routing, i.e. before or after
the channel fader. The dots let you
toggle the Aux bus between mono
and stereo.
25. This side bar, with the section labels
in it, can be shown or hidden using
Legend switch in the Contro ls
the
section of the side bar (item #3 in the
mixer tab on page 19).
26. Shows how much DSP power is being
used by the mixer hardware. To free
up DSP bandwidth, try reducing the
number of mixer ins, disabling
channel effects, reverb, etc. See “DSP
Usage” on page 66 for more info.
so it
MOTU AVB CONTROL WEB APP
21
MAIN MIX AND MONITOR CHANNEL STRIPS
1
2
3 4 5 6
3 4
14
13
12
11
7
To access the Main Mix and Monitor
channel strips, go to the mixer tab
(page 19) and scroll the display to the
right, beyond the inputs and groups.
To show and hide sections of the channel
strip, such as EQ or the Leveler, use the
Contro ls section of the side bar (item #3 in
SC
the mixer tab on page 19).
8
9
10
1. By default, the Monitor bus serves as
a solo bus. However, it can be set to
mirror the main mix bus, or any other
aux bus, group, or the reverb bus, in
addition to monitoring solo. Make
this choice in the source menu (12).
Use the Routing grid (page 18) to
specify the output for the Monitor
bus.
2. The Main Mix bus is the primary
stereo mix.
3. Provides hardware settings for any
assigned outputs that have them. For
example, if the Main Mix bus is
assigned to analog outputs on the
24Ao, you’ll see trim settings for the
outputs. This item is grayed out if
there are no hardware settings for
output.
4. Use this output assignment widget to
choose the destination — or multiple destinations — for the bus. You
can also make this setting directly on
the Routing grid (page 18).
5. Use the preset menus to create save,
recall, and otherwise manage
channel strip presets for the Monitor
bus and Main Mix bus.
6. Indicates that the bus is stereo.
7. The four-band parametric EQ for the
8. The Leveler provides specialized gain
9. Mutes for the Main Mix bus and
10. Master faders for the Main Mix bus
11. When
12. Choose the source for the Monitor bus
13. The
14. This mid-band EQ is currently
5
Main Mix bus operates the same as
described for input channels (items
10 and 11 on page 21), including
High and Low Shelf filter options.
reduction modeled after the legendary Teletronix LA-2A Leveling Amplifier. For complete details, see
“Leveler” on page 64.
Monitor bus.
and Monitor bus. Use the same
techniques described for input
channel faders (items 16, 17 and 18
on page 21).
Follow Solo is enabled, the
Monitor bus switches to the solo bus
when any channel is soloed. NOTE: if
an aux bus is soloed, then the Monitor
bus carries only the soloed aux bus
(any current channel solos are
excluded).
from this menu. It can mirror the
main mix, any aux bus, group, the
reverb bus, or it can serve only as a
Solo bus.
button clears all solos.
disabled (and therefore grayed out).
22
MOTU AVB CONTROL WEB APP
AUX BUS CHANNEL STRIPS
1
10
9
8
2
3
Aux busses can be used to create sub-mixes.
An aux bus can be assigned to any output in
4
5
6
7
the Routing grid (page 18).
To access an Aux bus channel strip, go to the
mixer tab (page 19), reveal the side bar (item
#3 on page 19), and then show the aux busses
you want in the
To show and hide the four-band EQ section of
the channel strip, use the
the side bar (item #3 in the mixer tab on
page 19).
1. A stereo aux bus.
2. A mono aux bus.
3. Click this dot to toggle an aux bus between
4. The four-band parametric EQ module for
5. Aux bus solo and mute.
6. Aux bus master fader.
7. Click to type specific value manually.
8. Click the dB scale numbers to make the
9. A disabled EQ band.
10. Use these menus (hardware settings,
Mixer Outputs section (26).
Contro ls section of
mono and stereo.
Aux busses operates the same as described
for input channels (items 10 and 11 on
page 21), including High and Low Shelf
filter options.
fader jump exactly to that level. Click and
drag horizontally to jump consecutive
faders to the same level.
output assignment, and presets) in a
similar fashion as described for the Main
Out bus (items 3-5 on page 22).
MOTU AVB CONTROL WEB APP
23
GROUP AND REVERB CHANNEL STRIPS
1
2
9
8
7
6
3
Group busses can be used to create a mix subgroup, which is a set of inputs you wish to
control together as a group. Groups differ from
aux busses in that they have aux sends, a reverb
send, as well as a main mix send. In addition,
group busses are equipped with the Leveler.
The Reverb bus is a special group bus that
4
5
provides a reverb processor. If you disable the
reverb, the reverb bus functions as a (four th)
regular group bus.
To access the Group and Reverb bus channel
strips, go to the mixer tab (page 19), reveal the
side bar (item #3 on page 19), and then show
the desired Group busses or Reverb bus in the
Mixer Outputs section (26).
To show and hide the four-band EQ section of
the channel strip, use the
side bar (item #3 in the mixer tab on page 19).
1. A Group bus channel strip. Click the name to
rename it. Delete the current name to return
to its default.
2. The Reverb bus. If you disable the Reverb
processor, it can be used as a fourth Group
bus. The Reverb channel strip is twice as
wide as other mixer channel strips to
accommodate the Reverb processor
controls.
3. Group busses and the Reverb bus are always
stereo.
4. The four-band parametric EQ module for
Group busses and the Reverb bus operates
the same as described for input channels
(items 10 and 11 on page 21), including
High and Low Shelf filter options.
5. The Reverb processor. For complete information, see “Reverb” on page 65.
6. Main Mix sends.
7. Master faders for the Group and Reverb
busses.
8. Mute and Solo.
9. Use these menus (hardware settings, output
assignment, and presets) in a similar
fashion as described for the Main Out bus
(items 3-5 on page 22).
Contro ls section of the
24
MOTU AVB CONTROL WEB APP
CHAPTER
1
About Your MOTU AVB Audio Interface
The 24Ai and 24Ao are hybrid USB2/AVB audio
interfaces with 48-channel digital mixers and AVB
Ethernet networking capability. They can operate
as audio interfaces for a computer, as stand-alone
digital mixers, as gateways to an expanded studio
system, as components of an extended AVB audio
network, or as capable hybrid devices performing
all of these roles simultaneously.
Together, they are designed to be a central
component of a modern, high performance
recording studio or live mixing platform. The
following sections provide a brief overview of their
main features and characteristics.
State-of-the-art A/D and D/A conversion
The analog section of each interface employs stateof-the-art 24-bit DACs or ADCs, which deliver
analog recording and playback with remarkably
high dynamic range at sample rates from 44.1 to
192 kHz.
Complementary I/O configurations
Each interface delivers an exceptional amount of
analog and digital audio. In addition, the interfaces
are designed to complement each other, and
MOTU’s other AVB-equipped audio interfaces, to
deliver a wide range of I/O options; you can mix
and match several interfaces and operate them as a
unified I/O and mixing system. The following
sections provide a bird’s-eye glance of the I/O
configurations offered by each interface in the
MOTU AVB family.
Each interface provides a variety of analog and
digital interconnects, all active simultaneously,
designed to provide everything you need for a wellequipped recording studio.
24Ai
72 simultaneous audio channels
Connection Input Output
Balanced analog on 3x D-sub or 6x Phoenix 24 -
ADAT optical digital (at 44.1 or 48 kHz) 24 24
Total 48 24
24Ao
72 simultaneous audio channels;
Connection Input Output
Balanced analog on 3x D-sub or 6x Phoenix - 24
ADAT optical digital (at 44.1 or 48 kHz) 24 24
Total 24 48
Network I/O
Each interface is also capable of handling
additional 8-channel banks of network audio input
and output for an additional 96 simultaneous
audio channels.
Other MOTU AVB interfaces
The 24Ai and 24Ao are part of a larger family of
audio interfaces, summarized below, with
complementary I/O configurations.
1248
66 simultaneous audio channels
Connection Input Output
Quarter-inch analog on bal/unbal TRS 8 12
Mic inputs with individual preamps on XLR 4 -
Hi-Z guitar inputs 2 -
Headphone output - 2 x stereo
ADAT optical digital (at 44.1 or 48 kHz) 16 16
RCA S/PDIF digital up to 96 kHz with SRC stereo stereo
Total 32 34
25
50 simultaneous audio channels
Connection Input Output
Quarter-inch analog on bal/unbal TRS - 8
Mic/guitar inputs on combo XLR/TRS 8 -
Headphone output - stereo
ADAT optical digital (at 44.1 or 48 kHz) 16 16
Total 24 26
16A
64 simultaneous audio channels
Connection Input Output
Quarter-inch analog on bal/unbal TRS 16 16
ADAT optical digital (at 44.1 or 48 kHz) 16 16
Total 32 32
Universal connectivity
The 24Ai and 24Ao can connect to a computer with
high-speed USB 2.0, which is compatible with USB
3.0). They are USB audio class-compliant, which
means that they are iPad compatible (with a
camera connection kit) and do not require driver
installation for USB connection to a computer.
On-board DSP with mixing and effects
Each interface is equipped with a powerful DSP
engi ne that drives both a n ext ensive routing m atri x
and a 48-input digital mixer with 12 stereo busses
and effects. The mixer offers familiar operation
modeled after large format mixing consoles.
32-bit floating point processing
All of the mixing and effects processing in the DSP
engine is handled with 32-bit floating point
calculations, to maintain and deliver virtually
unlimited headroom and the utmost in sound
quality.
Modeled vintage effects processing
Effects include “classic” reverb, compression
modeled after the legendary Teletronix LA-2A
compressor, and 4-band EQ modeled after British
analog console EQs.
AVB system expansion and audio networking
AV B stands for the IEEE 802.1 Audio Video
Bridging Ethernet standard for high-bandwidth,
low-latency audio streaming over Ethernet. The
AVB Ethernet network port on each MOTU
interface lets you add a second AVB-equipped
MOTU interface using any standard CAT-5e
Ethernet cable. You can network up to five MOTU
interfaces together using a MOTU AVB Switch™
(sold separately), and then run them as a standalone network or as an extended bank of I/Os for
your computer-based production system (or
both). You can even connect multiple computers,
each with full access to all devices on the network
(including the other computers).
With additional standard AVB switches (from
8M
MOTU or other brands) and standard Ethernet
cabling, you can build an extensive AVB audio
network. The entire network operates with nearzero network latency, even over very long cable
runs. MOTU’s AVB implementation allows you to
stream hundreds of audio channels among devices
and computers on the network with guaranteed
Quality of Service (QoS), prioritizing audio
streams over less important traffic.
Matrix routing and multing
Each MOTU interface provides completely flexible
matrix-style audio routing and multing. You can
route any analog or digital input, computer
channel, or network stream to any other output,
computer, or network device. You can also mult any
single input to unlimited multiple output
destinations.
26
ABOUT YOUR MOTU AVB AUDIO INTERFACE
24 channels of network audio I/O for your host computer
The 24Ai and 24Ao let you stream up to 24 audio
channels in and out, simultaneously, through their
USB connection to a host computer. Sources and
destinations can include inputs and outputs on the
device, inputs and outputs on other interfaces on
the network, and even audio software apps
running on other computers connected to other
devices on the network.
Web app control
You can control on-board DSP, mixing, device
settings, clock/sync settings, and network audio
routing from the MOTU AVB Control web app
software running in your favorite browser on a
laptop, tablet or smart phone connected to your
MOTU interface directly, or through your local
WiFi network. Multiple devices can be used simultaneously to access any audio interface settings on
the network.
Stand-alone mixing with wireless control
If you connect your MOTU interface to an Apple
Airport or other WiFi router with a standard
Ethernet cable, you can control its powerful mixing
and DSP effects from your smart phone or tablet,
without a computer — great for live sound mixing
from your iPad, tablet, or other wireless device.
ADAT digital I/O
The 24Ai and 24Ao interfaces each provide three
8-channel banks of optical digital I/O. Connect
outboard digital processors, digital mixers or other
gear: 24 channels at 44.1/48 kHz or 12 channels at
88.2/96 kHz.
sample rates (from 88.2 to 192 kHz). The word
clock OUT port can alternately be used as a THRU
port for word clock daisy-chaining. To configure,
use the LCD menu to navigate to Settings -> Word
Clock Thru Mode.
Comprehensive metering
The large backlit LCD displays all signal activity at
a glance with detailed metering for all analog and
digital I/O. You can access many hardware settings
directly from the front panel.
Precision Digital Trim™
Analog inputs are equipped with digitally
controlled analog trims, adjustable in 1 dB
increments. Analog outputs offer 32 bit trim in the
DAC, also adjustable in 1 dB increments. You can
save your tr im co nfigu rations as a pre set for instant
recall.
Rack mount or desktop operation
Each interface is housed in a sturdy, metal-alloy,
19-inch, rack-mountable unit. The rack mounting
brackets can be removed using a 7/64” hex wrench
for desktop operation.
AudioDesk
AudioDesk is a full-featured, audio workstation
software package included with the 24Ai and 24Ao.
AudioDesk provides multi-channel waveform
editing, automated virtual mixing, graphic editing
of ramp automation, real-time effects plug-ins with
crossfades, support for many third-party audio
plug-ins, sample-accurate editing and placement
of audio, and more.
Word clock
Each MOTU interface supports standard word
clock synchronization at any supported sample
rate. When the interface is operating at 96 kHz, it
can generate word clock output at either 96 or
48 kHz; the 1x equivalence is available as an option
for word clock output when running at high
ABOUT YOUR MOTU AVB AUDIO INTERFACE
27
Loading...