Motorola SBG941 User Manual

Software License, Warranty, Safety, and Regulatory Information

SURFboard

®

SBG941 Series Wireless Cable Modem Gateway

SAFETY AND REGULATORY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS — when using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all of the instructions listed here and/or in the user manual before you operate this device. Give

particular attention to all safety precautions. Retain the instructions for future reference.

• This device must be installed and used in strict accordance with manufacturer’s instructions, as described

in the user documentation that is included with the device.

• Comply with all warning and caution statements in the instructions. Observe all warning and caution

symbols that are affixed to this device.

• To prevent fire or shock hazard, do not expose this device to rain or moisture. The device must not be

exposed to dripping or splashing. Do not place objects filled with liquids, such as vases, on the device.

• This device was qualified under test conditions that included the use of the supplied cables between

system components. To ensure regulatory and safety compliance, use only the provided power and
interface cables and install them properly.

• Different types of cord sets may be used for connections to the main supply circuit. Use only a main line

cord that complies with all applicable device safety requirements of the country of use.

• Installation of this device must be in accordance with national wiring codes and conform to local

regulations.

• Operate this device only from the type of power source indicated on the device’s marking label. If you are

not sure of the type of power supplied to your home, consult your dealer or local power company.

• Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded

AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs
are dangerous. They may result in a shock or fire hazard.

• Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or

against them. Pay particular attention to cords where they are attached to plugs and convenience
receptacles, and examine the point where they exit from the device.

• Place this device in a location that is close enough to an electrical outlet to accommodate the length of

the power cord.

• Place the device to allow for easy access when disconnecting the power cord of the device from the AC

wall outlet.

• Do not connect the plug into an extension cord, receptacle, or other outlet unless the plug can be fully

inserted with no part of the blades exposed.

• Place this device on a stable surface.

• It is recommended that the customer install an AC surge protector in the AC outlet to which this device is

connected. This is to avoid damaging the device by local lightning strikes and other electrical surges.

• Postpone installation until there is no risk of thunderstorm or lightning activity in the area.

• Do not cover the device or block the airflow to the device with any other objects. Keep the device away

from excessive heat and humidity and keep the device free from vibration and dust.

• Wipe the device with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray

cleaners directly on the device or use forced air to remove dust.

• Do not use this product near water: for example, near a bathtub, washbowl, kitchen sink or laundry tub, in

a wet basement, or near a swimming pool.

1

Software License, Warranty, Safety, and Regulatory Information

SURFboard

®

SBG941 Series Wireless Cable Modem Gateway

• Upon completion of any service or repairs to this device, ask the service technician to perform safety

checks to determine that the device is in safe operating condition.

• Do not open the device. Do not perform any servicing other than that contained in the installation and

troubleshooting instructions. Refer all servicing to qualified service personnel.

• This device should not be used in an environment that exceeds 40º C.

SAVE THESE INSTRUCTIONS

Note to CATV System Installer — This reminder is provided to call the CATV system installer’s attention to
Section 820.93 of the National Electric Code, which provides guidelines for proper grounding and, in
particular, specifies that the Coaxial cable shield shall be connected to the grounding system of the building,
as close to the point of cable entry as practical.

FCC STATEMENTS

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the device off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.

FCC CAUTION: Any changes or modifications not expressly approved by Motorola for compliance could void the user’s authority to
operate the equipment.

FCC RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with the FCC RF
exposure compliance requirements, the separation distance between the antenna and any person’s body (including hands, wrists, feet
and ankles) must be at least 20 cm (8 inches).

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the
factory to match the intended destinations. The firmware setting is not accessible by the end user.

INDUSTRY CANADA (IC) STATEMENT

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IC RADIATION EXPOSURE STATEMENT

IMPORTANT NO TE: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

2