Motorola Netopia 6150285-00-02 User Manual
United States.
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful inter ference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful inter ference to radio communications. However, there is no guarantee that inter ference
will not occur in a particular installation. If this equipment does cause harmful inter ference to radio or
television reception, which can be determined by turning the equipment of f and on, the user is
encouraged to try to correct the inter ference by one or more of the following measures:
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to which the receiver is
■
connected.
■
Consult the dealer or an experienced radio TV technician for help.
This equipment has been tested and found to comply with the limits for a Class B digital
Safety and Certifications
Important Safety Instructions
POWER SUPPLY INSTALLATION
Connect the power supply cord to the power jack on the Motorola Netopia® Modem. Plug the power supply into an appropriate electrical outlet.
Service requirements.
Company or an authorized agent. Under FCC rules, no customer is authorized to repair this equipment.
This restriction applies regardless of whether the equipment is in or our of warranty. It is the responsibility
of users requiring service to repor t the need for ser vice to our Company or to one of our authorized
agents. Service can be obtained at Motorola, Inc., 1101 Marina Village Pkwy, Alameda, CA 94501.
Telephone: (510) 217-7660.
Important
shielded cables and connectors between system components. Changes or modifications to this product
not authorized by the manufacturer could void your authority to operate the equipment.
This product was tested for FCC compliance under conditions that included the use of
.
In the event of equipment malfunction, all repairs should be performed by our
Canada
This Class B digital apparatus meets all requirements of the Canadian Inter ference -Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel
brouilleur du Canada.
Declaration for Canadian users
NOTICE: The Canadian Industry Canada label identifies certified equipment. This
certification means that the equipment meets cer tain telecommunications
network protective, operation, and safety requirements. The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. In
some cases, the company’s inside wiring associated with a single line individual
service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to the certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made by
the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution
Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the
maximum number of terminals allowed to be connected to a telephone inter face. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed 5.
Part Number: 6150285-00-02
☛
CAUTION:
Depending on the power supply provided with the product, either the direct plug-in power
supply blades, power supply cord plug or the appliance coupler serves as the mains
power disconnect. It is important that the direct plug-in power supply, socket-outlet or
appliance coupler be located so it is readily accessible.
CAUTION (North America Only) : For use only with a CSA Certified or UL Listed Limited
Power Source or Class 2 power supply, rated 12Vdc.
TELECOMMUNICATION INSTALLATION
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
•
Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
•
remote risk of electrical shock from lightning.
•
Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
Description
Communications interfaces:
connections or an RJ-45 jack for cable/DSL modem connections and 1 or 4–port 10/100Base-T Ethernet
switch for your LAN connections. Some models have a USB port that can be used to connect to your PC;
in some cases, the USB port also serves as the power source. Some models contain an 802.11b/g
wireless LAN transmitter.
Power requirements
■
12 VDC input
Environment
Operating temperature:
Storage temperature:
Relative storage humidity:
0° to +70° C
The Motorola Netopia® Gateways have an RJ-11 jack for DSL line
0° to +40° C
20 to 80% noncondensing
attached, they may not ring properly.
could void the user’s authority to operate the equipment.
Changes or modifications to this unit not expressly approved by the par ty responsible for compliance
include increasing the physical distance between this product and other electrical devices.
interference, in which case the user may be required to take adequate measures. Adequate measures
This is a Class B product. In a domestic environment this product may cause radio
Warnings:
Manufacturer’s Declaration of Conformance
use of a surge arrestor or similar protection device.
nationwide problem. Therefore it is advised that this equipment be connected to AC power through the
customer terminal equipment connected to AC power sources. This has been identified as a major
Telephone companies report that electrical surges, typically lightning transients, are ver y destr uctive to
Electrical Safety Advisory
and any body part of the user to be in compliance with FCC RF exposure guidelines.
NOTE:
Installation of the wireless models must maintain at least 20 cm between the wireless router
RF Exposure Statement:
installer.
have questions about what will disable alarm equipment, consult your telephone company or qualified
installation of this Motorola Netopia® 2200 Series router does not disable your alarm equipment. If you
j) If your home has specially wired alarm equipment connected to the telephone line, ensure the
public service commission or corporation commission for information.
i) Connection to party line service is subject to state tariffs. Contact the state public utility commission,
the troubleshooting section of the Product User Manual before calling Motorola Technical Support.
h) This equipment not intended to be repaired by the end user. In case of any problems, please refer to
disconnect the equipment until the problem is resolved.
If the equipment is causing harm to the telephone network, the telephone company may request that you
www.Motorola.com.
510-217-7660
Motorola Technical Support
warranty information, please contact:
g) If trouble is experienced with this equipment, the Motorola Netopia® 2200 Series router, for repair or
notice in order for you to make necessary modifications to maintain uninterrupted service.
could affect the operation of the equipment. If this happens the telephone company will provide advance
f) The telephone company may make changes in its facilities, equipment, operations or procedures that
necessary.
possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is
required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as
the telephone company will notify you in advance that temporary discontinuance of service may be
e) If this equipment, the Motorola Netopia® 2200 Series router, causes harm to the telephone network,
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a
company. For products approved after July 23, 2002, the REN for this product is part of the product
devices that may be connected to a line, as determined by the total RENs, contact the local telephone
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call.
d) The REN is used to determine the number of devices that may be connected to a telephone line.
compatible modular jack that is also compliant. See installation instructions for details.
telephone cord and modular plug is provided with this product. It is designed to be connected to a
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
c) A plug and jack used to connect this equipment to the premises wiring and telephone network must
b) List all applicable certification jack Universal Service Order Codes (“USOC”) for the equipment: RJ11.
format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
the bottom of this equipment is a label that contains, among other information, a product identifier in the
a) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On
FCC Statements
HTTP (Web server)
Ping, event logging, routing table displays, statistics counters, web-based management,
PPPoA, PPPoE, DHCP, static IP address
Software preloaded on internal flash memor y; field upgrades done via download to
the REN's of all devices on any one line should not exceed five (5.0). If too many devices are
determine how many devices can be connected to your telephone line. In most areas, the sum of
Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to
d. The FCC Registration Number. [XXXUSA-XXXXX-XX-E]
c. The USOC jack required. [RJ11C]
b. The ringer equivalence number. [0.XB]
a. The telephone number to which this unit is connected.
inform them of:
4. If the telephone company requests information on what equipment is connected to their lines,
adequate notice of the changes. You will be advised of your right to file a complaint with the FCC.
changes affect the compatibility or use of this device, the telephone company is required to give
3. The telephone company may make changes in its technical operations and procedures; if such
made. If this is not done, the telephone company may temporarily disconnect service.
should be disconnected until the source of the problem can be determined and until repair has been
2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device
This equipment should not be used on party lines or coin phones.
be directly connected to the telephone network. Standardized jacks are used for these connections.
1. The Federal Communications Commission (FCC) has established Rules which permit this device to
FCC Requirements
47 CFR Part 68 Information
■
Canada – CS-03
United States – 47 CFR Part 68
■
Telecom:
■
Canada – ICES-003
■
United States – FCC Part 15 Class B
EMC:
■
Canada – CSA: CAN/CSA-C22.2 No. 60950-00
■
United States – UL 60950, Third Edition
Safety Approvals:
North America
Agency approvals
traceroute, nslookup, and diagnostic commands.
Diagnostics:
Management/configuration methods:
PAP, CHAP, UI password security, IPsec
TCP/IP Internet Protocol Suite, RIP
Security:
WAN support:
Routing:
internal flash memor y via TFTP or web upload.
Software media:
Software and protocols
Loading...