Motorola NETOPIA 2210-02 User Manual
User Manual
The Motorola Netopia® 2210-02
ADSL2+ Gateway
Single-port Ethernet
Safety Information
IMPORTANT SAFETY INSTRUCTIONS – POWER SUPPLY INSTALLATION.
the power jack on the Motorola Modem. Plug the power supply into an appropriate electrical outlet.
CAUTION:
ply cord plug or the appliance coupler serves as the mains power disconnect. It is important that the direct plug-in power supply,
socket-outlet or appliance coupler be located so it is readily accessible.
(Sweden)
ENGLISH
(Norway)
TELECOMMUNICATION INSTALLATION.
should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
• Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock
• Do not use the telephone to report a gas leak in the vicinity of the leak.
PRODUCT VENTILATION.
this product should not exceed 104°F (40°C). It should not be used in locations exposed to outside heat radiation or trapping of its
own heat. The product should have at least one inch of clearance on all sides except the bottom when properly installed and should
not be placed inside tightly enclosed spaces unless proper ventilation is provided.
SAVE THESE INSTRUCTIONS
Motorola Part Number:
Copyright © 2007 by Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation,
transformation or adaptation) without written permission from Motorola, Inc.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s)
described in this manual at any time. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Microsoft, Windows, Windows Me, and Windows NT are either trademarks or registered trademarks of Microsoft Corporation in the U.S and/or other countries. Macintosh is a registered trademark of Apple, Inc. Firefox is a registered trademark of the Mozilla Foundation. All other product or service names are the property of their
respective owners.
Depending on the power supply provided with the product, either the direct plug-in power supply blades, power sup-
Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk
Apparatet må kun tilkoples jordet stikkontakt.
When using your telephone equipment, basic safety precautions
near a swimming pool.
from lightning.
The Motorola Modem is intended for use in a consumer's home. Ambient temperatures around
6180206-00-01
Connect the power supply cord to
2
1
Checklist
Thank you for selecting the Motorola Netopia® 2210-02 ADSL2+ Gateway. This guide will help you set
up and configure your network.
Check your package contents. It should contain the items shown here:
CD and
Motorola Modem User Manual
Wallmount Template
ENGLISH
Power
Supply
If you don’t have everything, contact your supplier immediately.
Gray RJ-11
Phone Cable
Yellow RJ-45
Ethernet Cable
3
2
Connections
Note:
ENGLISH
Macintosh users: skip to Step #2 below.
1. Windows users: Insert the Motorola Netopia CD into your CDROM drive. The
Installation Guide Wizard should start automatically and the Welcome screen
should appear to step through your connection installation(s).
The Motorola Netopia Installation Guide Wizard automates several tasks to get you up and
running easily. Run the Wizard on every Windows-based PC that will connect to your network.
Click the
Next
button.
Follow the on-screen instructions to make all
of your connections.
2. Locate the Modem near a power source, a DSL wall outlet, and in a location
where air can circulate freely around it.
3. Connect the rounded end of the power supply to the power jack on the back panel
of the Modem. Then, plug the power supply into an electrical outlet.
The
Power
LED should light solid green.
4. Connect one end of the gray RJ-11 Phone cable to the port labeled “DSL” on the
Modem. Connect the other end of the Phone cable to your DSL wall outlet.
4
5. Connect one end of the yellow RJ-45 Ethernet cable to the port labeled “Ethernet”
on the modem. Connect the other end of the Ethernet cable to the Ethernet port on
your PC.
Rear View
DSL Port
Ethernet
Port
ENGLISH
5
When all of your connections are made, the status LEDs on the front of your Motorola Modem
will light, according to the following diagram:
Top View
ENGLISH
Power -
Solid Green = Power on
Off = Power off
Flashing Red = Power On/Self Test
Solid Red = PO/ST Failure
Ethernet -
Solid green = Device connected.
Off = No device connected or
modem power is off
6
Internet -
Solid green = Connected to Internet
Off = Bridge mode or
modem power is off
Flashing green = Attempting PPP
connection
Red = Connection failed
DSL -
Solid green = DSL synch
Off = Modem power off
Flashing green = DSL attempting synch
Flashing green/red = DSL fails to synch 3 times
Flashing red = No DSL signal
Loading...