Motorola MTX1550, MTX4550 User Manual

Download

Page 1

Page 2

Page 3

CONTENTS

COMPUTER SOFTWARE

COPYRIGHTS . . . . . . . . . . . . . . . . . . . . . . 4

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Radio Overview . . . . . . . . . . . . . . . . . . . . 6

Parts of the Radio . . . . . . . . . . . . . . . . . . . 6

MTX1550 and MTX4550 Models . . . . . 6

On/Off/Volume Knob. . . . . . . . . . . . . . . 7

Mode Selector Knob . . . . . . . . . . . . . . . 7

Push-to-Talk (PTT) Button . . . . . . . . . . 7

LED Indicator . . . . . . . . . . . . . . . . . . . . 7

Microphone . . . . . . . . . . . . . . . . . . . . . . 7

Programmable Buttons . . . . . . . . . . . . . 7

Keypad Keys (For Model II Radios

Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Menu Keys (For Model II Radios

Only) . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Selecting a Feature. . . . . . . . . . . . . . . 10

Menu Display . . . . . . . . . . . . . . . . . . . 11

LCD Screen and Icons . . . . . . . . . . . . 11

Alert Tone Indications . . . . . . . . . . . . . 12

Getting Started . . . . . . . . . . . . . . . . . . . . 14

Battery Information. . . . . . . . . . . . . . . . . . 14

Battery Care and Tips . . . . . . . . . . . . . 14

Recycling or Disposal of Batteries . . . .15

Charging the Battery . . . . . . . . . . . . . . 15

Accessory Information . . . . . . . . . . . . . . . .16

Attaching the Battery . . . . . . . . . . . . . .16

Removing the Battery. . . . . . . . . . . . . .16

Attaching the Antenna . . . . . . . . . . . . .17

Removing the Antenna. . . . . . . . . . . . .17

Attaching the Belt Clip . . . . . . . . . . . . .18

Removing the Belt Clip. . . . . . . . . . . . . 18

Radio Operation . . . . . . . . . . . . . . . . . . . . 19

Turning the Radio On or Off . . . . . . . . .19

Adjusting the Radio’s Volume . . . . . . .19

Radio Self Test. . . . . . . . . . . . . . . . . . .19

Basic Radio Calls . . . . . . . . . . . . . . . . . .20

Selecting a Zone and Mode. . . . . . . . . . . .20

Selecting a Zone (For Model II

Radios Only). . . . . . . . . . . . . . . . . . . . . 20

Selecting a Mode . . . . . . . . . . . . . . . . .20

Receiving a Call. . . . . . . . . . . . . . . . . . . . .21

Making a Call. . . . . . . . . . . . . . . . . . . . . . .21

Conventional Modes. . . . . . . . . . . . . . .21

Trunked Modes . . . . . . . . . . . . . . . . . . 21

Low-Battery Alert . . . . . . . . . . . . . . . . . 22

Coded Squelch Operation . . . . . . . . . .22

CONTENTS

20L01-A_PR_UG_MTX4500.book Page 1 Friday, April 13, 2007 2:47 PM

Page 4

CONTENTS

Variable RF Power Level (Selected

Models Only) . . . . . . . . . . . . . . . . . . . . 22

Failsoft Operation (Trunked Systems

Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Muting the Keypad Tones (For Keypad

Radios Only). . . . . . . . . . . . . . . . . . . . . . . 23

Trunked Features . . . . . . . . . . . . . . . . . . 24

Viewing Your Radio’s ID Number . . . . . . . 24

Enhanced Private Call Operation . . . . . . . 24

Answering a Private Call . . . . . . . . . . . 24

Making a Private Call. . . . . . . . . . . . . . 25

Leaving a Call Alert Page . . . . . . . . . . 28

Call Alert Operation . . . . . . . . . . . . . . . . . 29

Answering a Call Alert Page with a

Group Call . . . . . . . . . . . . . . . . . . . . . . 29

Making a Call Alert . . . . . . . . . . . . . . . 29

Automatic Multiple Site Selection

(AMSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Viewing the Current Site . . . . . . . . . . . 32

Forcing a Site Change. . . . . . . . . . . . . 32

Locking and Unlocking a Site . . . . . . . 32

Conventional Features. . . . . . . . . . . . . . 33

Repeat/Direct . . . . . . . . . . . . . . . . . . . . . . 33

Smart PTT . . . . . . . . . . . . . . . . . . . . . . . . 34

Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Scan Operation . . . . . . . . . . . . . . . . . . . . 35

Turning Scan On or Off with the Keypad (For Keypad Radios Only) . . . 35

Deleting Nuisance Modes . . . . . . . . . . 36

Viewing a Scan List (For Keypad

Radios Only) . . . . . . . . . . . . . . . . . . . . 36

Programming a Scan List (For

Keypad Radios Only) . . . . . . . . . . . . . 37

Scan Modes . . . . . . . . . . . . . . . . . . . . 38

Programming the Radio . . . . . . . . . . . . 39

Programming the Telephone List

Numbers . . . . . . . . . . . . . . . . . . . . . . . 39

Programming the Call List. . . . . . . . . . 40

Telephone Operation . . . . . . . . . . . . . . . 42

Answering a Telephone Call . . . . . . . . 42

Making a Telephone Call (For

Model II Radios Only) . . . . . . . . . . . . . 42

Special Features. . . . . . . . . . . . . . . . . . . 46

Emergency Operation . . . . . . . . . . . . . . . 46

Sending an Emergency Alarm . . . . . . 46

Sending a Silent Emergency Alarm . . 47

20L01-A_PR_UG_MTX4500.book Page 2 Friday, April 13, 2007 2:47 PM

Page 5

CONTENTS

Canceling an Emergency Alarm . . . . . 47

Sending an Emergency Call . . . . . . . . 47

Ending an Emergency Call . . . . . . . . . 48

Emergency with Voice to Follow . . . . . 48

Dynamic Regrouping. . . . . . . . . . . . . . . . . 48

Mode Selection . . . . . . . . . . . . . . . . . . 48

Select Enable and Disable. . . . . . . . . . 49

SmartZone Operation . . . . . . . . . . . . . . . 50

Benefits of SmartZone . . . . . . . . . . . . . . . 50

Site Switching in SmartZone . . . . . . . . 51

Viewing the Current Site . . . . . . . . . . . 52

Forcing a Site Change . . . . . . . . . . . . . 52

Locking and Unlocking a Site. . . . . . . . 52

Preferred Site Selection . . . . . . . . . . . . 53

Busy Override . . . . . . . . . . . . . . . . . . . 53

Site Trunking . . . . . . . . . . . . . . . . . . . . 54

Stat-Alert Features . . . . . . . . . . . . . . . . . 55

Viewing Your Radio’s ID Number . . . . . . . 55

Stat-Alert Voice Selective Call

Operation . . . . . . . . . . . . . . . . . . . . . . . . . 55

Receiving a Voice Selective Call . . . . . 56

Making a Voice Selective Call . . . . . . . 56

Stat-Alert Call Alert Operation. . . . . . . . . . 58

Receiving a Call Alert Page . . . . . . . . . 58

Making a Call Alert. . . . . . . . . . . . . . . . 59

PTT-ID . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Radio Check. . . . . . . . . . . . . . . . . . . . . . . 60

Emergency Operation. . . . . . . . . . . . . . . . 60

Accessories . . . . . . . . . . . . . . . . . . . . . . 61

Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Antennas . . . . . . . . . . . . . . . . . . . . . . . . . 61

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Carry Cases . . . . . . . . . . . . . . . . . . . . . . . 61

Chargers. . . . . . . . . . . . . . . . . . . . . . . . . . 61

Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Headsets . . . . . . . . . . . . . . . . . . . . . . . . . 62

Remote Speaker Microphones. . . . . . . . . 62

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 63

Limited Warranty . . . . . . . . . . . . . . . . . . 63

20L01-A_PR_UG_MTX4500.book Page 3 Friday, April 13, 2007 2:47 PM

Page 6

COMPUTER SOFTWARE

COPYRIGHTS

COMPUTER SOFTWARE COPYRIGHTS

The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.

Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverseengineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product.

20L01-A_PR_UG_MTX4500.book Page 4 Friday, April 13, 2007 2:47 PM

Page 7

SAFETY

This user guide covers the operation of the MTX1550 and MTX4550 Portable Radios.

This radio is restricted to occupational use only to satisfy ICNIRP RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet (Motorola Publication part number 6881095C98_) to ensure compliance with RF energy exposure limits.

Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet 6881095C98_ enclosed with your radio.

Caution

20L01-A_PR_UG_MTX4500.book Page 5 Friday, April 13, 2007 2:47 PM

Page 8

RADIO OVERVIEW

PARTS OF THE RADIO

MTX1550 and MTX4550 Models

(Programmable)/

Side Button 1 (A)

(Programmable)

Side Button 3 (C)

(Programmable)

Top Button (D)

Keypad

Menu Keys

Mode Selector Knob

Button

Push-to-Talk (PTT)

On/Off/Volume Knob

LED Indicator

(Programmable)

Side Button 2 (B)

LCD Screen

Microphone

Select Button

Side

Connector

Cover

Side

Connector

Cover

20L01-A_PR_UG_MTX4500.book Page 6 Friday, April 13, 2007 2:47 PM

Page 9

RADIO OVERVIEW

On/Off/Volume Knob

Turns the radio on or off, and adjusts the radio’s volume.

Mode Selector Knob

Selects the required operation mode.

Push-to-Talk (PTT) Button

Press and hold down this button to talk; release to listen.

LED Indicator

Indicates status of radio operating conditions (see table below):

Microphone

When sending a message, hold the microphone 1 to 2 inches (2.5 to 5 cm) away from your mouth, and speak clearly into the microphone.

Programmable Buttons

Several of your radio buttons can be programmed (by using the Customer Programming Software — CPS) to activate the radio features.

Programmable buttons are:

• Top button

• Three side buttons

Check with your dealer or Motorola representative for a complete list of the functions your radio’s programmable buttons support.

With PTT Switch Pressed (Radio Transmitting)

Steady red

Radio is transmitting (PTT button pressed)

LED unlit Radio is not transmitting

Blinking red

Low battery (conventional mode only; programmable by authorized Motorola dealer).

Momentary green

Radio has powered-up successfully

With PTT Released (Radio Receiving)

Blinking red

Mode busy (conventional mode only)

Blinking green

Receipt of a telephone call, Private Conversation call, or Call Alert page

20L01-A_PR_UG_MTX4500.book Page 7 Friday, April 13, 2007 2:47 PM

Page 10

RADIO OVERVIEW

The table below shows the functions available by:

• short press - quickly pressing and releasing the

programmable buttons, or

• long press - pressing and holding the

programmable buttons for a period of time

before releasing, or

• hold down- pressing and holding down the

programmable buttons while checking status or making adjustments.

Button Short Press Long Press Hold Down

Monitor/Permanent Monitor

—

Continually monitors the selected channel.

Monitors the selected channel for any activity.

Volume Set — —

Sounds a tone for adjusting the radio’s volume level.

Scan

Toggles between the start/stop of the Scan operation.

— —

Nuisance Delete

Temporarily deletes an unwanted non-priority active scan member.

— —

Search Makes a system search. Light Turns on/off your radio’s backlight. — — Emergency Enters Emergency mode. Leaves Emergency mode. — Call Enters or exits a Private call. Page Enters or exits a Call Alert.

Call Response

Respond to or exit from a Private Call or Call Alert.

— —

Phone Enters or leaves Phone mode. — —

20L01-A_PR_UG_MTX4500.book Page 8 Friday, April 13, 2007 2:47 PM

Page 11

RADIO OVERVIEW

Keypad Keys (For Model II Radios Only)

These keys are used when dialing a phone number, making a radio call or entering information for programming the radio’s lists.

The following table shows the character cycle for each key, when entering information for programming the radio’s lists.

Note: The sequence in the table above is valid

when entering information on a blank display. However, when editing existing information, the above sequence may differ. For instance, if the last character entered is a “R”, pressing 7 to enter the next character, would start the character cycle at “S” and NOT at “P”.

• When editing existing information, pressing 1 would ALWAYS start the character cycle at the “blank space” and NOT at “1”.

Key

Number of Times the Key is Pressed

1 2 3 4 5 6

0 0

1 1

Blank space

2 A B C 2

3 D E F 3

4 G H I 4

123 456 789 *0#

5 J K L 5

6 M N O 6

7 P Q R S 7

8 T U V 8

9 W X Y Z 9

# # - + . / \

20L01-A_PR_UG_MTX4500.book Page 9 Friday, April 13, 2007 2:47 PM

Page 12

RADIO OVERVIEW

Menu Keys (For Model II Radios Only)

Selecting a Feature

A unique feature of your radio is its use of the display to give you quick access to many of the radio’s features without having to have a dedicated key for each feature.

The names of the features (CALL, MUTE, etc.) are shown on the display, three at a time. Selection of features is controlled by the three keys directly below the feature names: the left key controls the left feature, the middle key controls the middle feature, and the right key controls the right feature.

Softkeys (l;l)

When already in Menu Mode, these keys are used to make Menu selections.

Left and Right Arrow Keys (,/)

The left and right arrow keys are used to scroll the display forward or backward through the radio’s features and lists. There is no end point to the list, so if you continue to scroll in one direction, the display will “wrap around” back to the beginning of the list. If you hold either key down, the display scrolls at a faster rate until the key is released.

The left arrow key is also used for editing when you are entering information manually from the keypad.

Pressing the left arrow key, when editing numeric information (such as telephone numbers), will backspace, and erase the display, one character at a time. If you have erased all the digits, an additional press of the left arrow key returns the display to the preprogrammed list.

Pressing the left arrow key, when editing alphabetic information (such as member’s names), moves the cursor one step to the left.

HOME Key ( )

The HOME key always returns you to the home (default) display. In most cases, this is the current mode. In addition, if you are using a feature that requires it, pressing the HOME key also causes information to be saved in memory before going to the home display.

l;l ,/

Softkey 1

Softkey 3

Left Home

Right

Softkey 2

20L01-A_PR_UG_MTX4500.book Page 10 Friday, April 13, 2007 2:47 PM

Page 13

RADIO OVERVIEW

Some radio features automatically go to the home display when they are completed, without having to press the HOME key, thus reducing the number of key presses required.

Menu Display

The menu items can be displayed in normal video or in reversed video (programmable through the CPS). All the menu items in the examples in this manual are shown in reversed video.

The order in which the menu items are displayed is programmable. Thus, the order of the menu items on your radio may differ from those shown here in this manual. In such a situation, press the relevant softkey to make your menu selections. All descriptions of functions and displays after the selection are valid.

LCD Screen and Icons

The screen displays mode selected, channel, menu, and radio status information. The top two screen rows

show radio status indicator symbols, explained in the following table.

Symbol Name and Description

XPAND™ Indicator

Indicates that your radio has the companding feature activated.

Power Level Indicator

R lights up when your radio is configured to transmit in Low Power. S lights up when your radio is configured to transmit in High Power.

Carrier Squelch Indicator

Indicates when the active conventional mode is being monitored in the carrier squelch mode; ON = BEING MONITORED/

OFF = NOT BEING MONITORED.

Call Received

Blinks when a call or page is received.

Scan Indicator

Indicates when the radio is scanning; ON = SCANNING / OFF = NOT SCANNING.

Priority Scan

The presence of a dot along with the scan annunciator indicates the receiving of a priority mode; BLINKING DOT = PRIORITY 1 SOLID DOT = PRIORITY 2.

20L01-A_PR_UG_MTX4500.book Page 11 Friday, April 13, 2007 2:47 PM

Page 14

RADIO OVERVIEW

Alert Tone Indications

Your radio generates a number of audible tones to indicate radio operating conditions:

• Low Battery – A low-battery condition is indicated by a high-pitched, cricket-like “chirpchirp” when the PTT switch is released following a transmission.

• Successful Power-Up – A short, medium-pitched tone when the radio is first turned on indicates that the radio has passed its power-up self test and is ready for use.

• Unsuccessful Power-Up – A short, low-pitched tone when the radio is first turned on indicates that the radio has failed its power-up self test and is not ready for use. Contact your service representative for service.

• Transmit on Receive-Only Mode – If you press the PTT switch while tuned to a “receive-only” mode, you will hear a continuous, low-pitched alert tone, indicating that no transmission is possible on this mode. This tone will continue until the PTT switch is released.

• Transmit Inhibit on Busy Mode – If you press the PTT switch while the mode is busy, you will hear a continuous, low-pitched alert tone, indicating that no transmission is possible on this mode. This tone will continue until the PTT switch is released.

• Transmit Inhibit on Flat Battery – If you press the PTT while the battery is flat, you will hear a continuous, low pitched alert tone, indicating that transmission is impossible.

• Invalid Mode – A continuous, low-pitched tone is heard when an invalid or unprogrammed operation is attempted on the radio.

Direct

Indicates whether you are talking directly to another radio (talkaround), or through a repeater; ON = DIRECT OFF = REPEATER.

Programming/Viewing Mode

Indicates when the radio is in the programming or viewing mode; ON = IN VIEWING MODE BLINKING = IN PROGRAMMING MODE.

Signal Quality Indicator

Shows the radio signal quality. Five bars indicates the best signal (Smart Zone Only).

Battery Level Indicator

Shows the remaining charge in your battery, based on how many bars are displayed.

Blinking, indicates flat battery.

Symbol Name and Description

20L01-A_PR_UG_MTX4500.book Page 12 Friday, April 13, 2007 2:47 PM

Page 15

RADIO OVERVIEW

• Valid (Good) Key Press – A short, mediumpitched tone when a keypad key is pressed indicates that the key press was accepted.

• Invalid (Bad) Key Press – A short, low-pitched tone when a keypad key is pressed indicates that the key press was rejected.

• Emergency Alarm Entry – A short, mediumpitched tone when the emergency button is pressed indicates that the radio has entered the emergency mode.

• Emergency Alarm/Call Exit – A continuous, medium-pitched tone when the radio is in the emergency mode indicates that the radio has exited the emergency mode.

• Failsoft (Trunked Systems Only) – A faint “beeping” tone every ten seconds indicates that the radio is operating in the failsoft mode.

• Time-Out Timer Warning – Your radio’s time-out timer limits the length of your transmission time. When you are pressing the PTT switch (transmitting), a short, low-pitched warning tone will sound four seconds before the allotted time expires.

• Time-Out Timer Timed-Out – If you hold down the PTT switch longer than the time-out timer’s allotted time, a continuous, low-pitched tone sounds, indicating that your transmission has been cut off. This tone will continue until the PTT switch is released.

• Phone Busy – A “bah-bah-bah-bah” tone when telephone interconnect is accessed indicates that all available modes are busy and the radio is in queue for the next available phone line.

• Call Alert™ (Page) Received – A group of four medium-pitched tones every five seconds indicates that your radio has received a Call Alert page.

• Call Alert™ (Page) Sent – A single mediumpitched tone (central acknowledge), followed by a group of four medium-pitched tones indicates that a Call Alert page sent by your radio has been received by the target radio.

• Private Conversation™ Call Received – A group of two medium-pitched tones indicates that your radio has received a Private Conversation call. This sequence is repeated every five seconds for approximately 20 seconds for enhanced Private Conversation.

• Trunked System Busy (Trunked Systems Only) – A “bah-bah-bah-bah” tone when a trunked system is accessed indicates that all available channels are busy and the radio is in queue for the next available channel.

• Call Back (Trunked Systems Only) – A group of three medium-pitched tones (di-di-dit) indicates that a talkgroup is now available for your previously requested transmission.

20L01-A_PR_UG_MTX4500.book Page 13 Friday, April 13, 2007 2:47 PM

Page 16

GETTING STARTED

BATTERY INFORMATION

Battery Care and Tips

This product is powered by a lithium-ion rechargeable battery.

The following battery tips will help you obtain the highest performance and longest cycle life from your Motorola rechargeable battery.

• Charge your new battery overnight (14 – 16 hours) before using it to obtain maximum battery capacity and performance.

• Charging in non-Motorola equipment may lead to battery damage and void the battery warranty.

• When charging a battery that is attached to the radio, turn the radio off to ensure a full charge.

• The battery should be at about 25°C (room temperature) whenever possible. Charging a cold battery (below 10°C) may result in leakage of electrolyte and ultimately, in failure of the battery.

• Charging a hot battery (above 35°C) results in reduced discharge capacity, affecting the performance of the radio. Motorola rapid-rate battery chargers contain a temperature-sensing circuit to ensure that the battery is charged within these temperature limits.

• New batteries can be stored up to two years without significant cycle loss. Store new/unused batteries in a cool dry area.

• Batteries which have been in storage should be charged overnight.

• Do not return fully charged batteries to the charger for an “extra boost”. This action significantly reduces cycle life.

• Do not leave your radio and battery in the charger when not charging. Continuous charging shortens battery life. (Do not use your charger as a radio stand.)

• For optimum battery life and operation use only Motorola brand chargers. They were designed to operate as an integrated energy system.

20L01-A_PR_UG_MTX4500.book Page 14 Friday, April 13, 2007 2:47 PM

Page 17

GETTING STARTED

Recycling or Disposal of Batteries

Motorola endorses and encourages the recycling of all re-chargeable batteries. Contact your local Motorola dealer for further information.

Charging the Battery

If a battery is new, or its charge level is very low, indicated by battery level indicator showing one or no segments, you need to charge the battery before you can use it in your radio.

Note:

• Batteries are shipped uncharged from the factory. New batteries could prematurely indicate full charge, charge a new battery for 14 – 16 hours before initial use.

• Battery charging must occur ONLY in nonhazardous areas.

1. Place the radio with the battery attached, or the

battery alone, in the charger.

2. The charger’s LED indicates the charging

progress.

Battery chargers will charge only the Motorola authorized batteries listed below; other batteries will not charge.

NiCd

Charger LED Status

Red Battery is charging

Green Battery is fully charged

Blinking Red* Battery is unchargeable

Blinking Yellow Charger is getting ready to charge

Blinking Green Battery is 90% charged

Battery is damaged. Please contact your dealer.

Part No. Description

NNTN5510 Li-Ion Battery 1480mAH (FM_C)

20L01-A_PR_UG_MTX4500.book Page 15 Friday, April 13, 2007 2:47 PM

Page 18

GETTING STARTED

ACCESSORY INFORMATION

Attaching the Battery

Removing the Battery

1 Fit the extensions at the bottom of the

battery into the bottom slots of the radio.

2 Press the top part of the battery towards the

radio until you hear a click.



1 Turn off the radio (see page 19).

2 Slide both battery latches downward.

3 Pull the top part of the battery away from the

radio.

Battery Latches

20L01-A_PR_UG_MTX4500.book Page 16 Friday, April 13, 2007 2:47 PM

Page 19

GETTING STARTED

Attaching the Antenna Removing the Antenna

1 Align the threaded end of the antenna with the

radio’s antenna connector.

2 Turn the antenna clockwise to fasten it.

1 Turn the antenna counterclockwise until you can

remove it.

20L01-A_PR_UG_MTX4500.book Page 17 Friday, April 13, 2007 2:47 PM

Page 20

GETTING STARTED

Attaching the Belt Clip Removing the Belt Clip

1 Align the grooves of the belt clip with those

of the battery.

2 Press the belt clip downward until you hear

a click.

1 Use a key to press the belt clip tab away

from the battery.

2 Slide the belt clip upward to remove it.



Belt Clip Tab

20L01-A_PR_UG_MTX4500.book Page 18 Friday, April 13, 2007 2:47 PM

Page 21

GETTING STARTED

RADIO OPERATION Turning the Radio On or Off

Adjusting the Radio’s Volume

Radio Self Test

Turn the radio on by rotating the volume control clockwise. The radio goes through a power-up self check and, if it passes the check, the display momentarily shows SELF TEST. A good-power-up, high-pitched tone sounds to indicate that the radio has passed the self check.

If the radio fails the self check, the display shows ERROR XX/XX (where XX/XX is an alphanumeric error code), accompanied by a bad-power-up, low-pitched tone. Turn the radio off, check the battery, and turn the radio back on. If the radio still does not pass the self check, a problem exists in the radio. Contact your nearest Motorola Service Shop.

Note: The power-up self check verifies that the

radio’s microprocessor-based systems are working, but it does not check all of the rf components, nor does it check the operation of all customer-specific features. Motorola recommends that the functionality of the radio be periodically checked by an authorized Motorola service shop.

To turn the radio on, turn the On-Off/Volume Control knob clockwise.

To turn the radio off, turn the On-Off/Volume Control knob counterclockwise until you hear a click.

Turn the On-Off/Volume Control knob to adjust the volume level.

Listen until you hear a transmission, then adjust the volume control for a comfortable listening level.

Or, if a button is programmed for “volume set,” press this button and adjust the volume to a comfortable listening level.

ON OFF

20L01-A_PR_UG_MTX4500.book Page 19 Friday, April 13, 2007 2:47 PM

Page 22

BASIC RADIO CALLS

This section outlines the basic functions of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

SELECTING A ZONE AND MODE

A mode is a channel or talkgroup and all the features that are programmed to it. A zone is a grouping of modes that is selected using the menu keys. Before you use your radio to receive or send messages, you should first select the desired zone and mode.

Selecting a Zone (For Model II Radios Only)

Selecting a Mode

1 Press / until

ZONE is displayed.

2 Press l (the

softkey below ZONE). The current zone name blinks on the display.

For example

PLANT POLICE

ZONE

MUTE

CALL

PLANT POLICE

3 Press / until the

desired zone name is displayed.

—or—

Enter the number of the desired zone.

For example

4 Press .

5 The displayed zone is

the new selected zone.

1 Turn the mode selector knob to the desired

mode.

2 The display shows

the selected mode’s name.

For example

3 If the selected mode

is unprogrammed, an invalid-mode tone is heard until a valid programmed mode is selected.

CITY POLICE

PLANT MODE 1

UNPROGRAMMED

20L01-A_PR_UG_MTX4500.book Page 20 Friday, April 13, 2007 2:47 PM

Page 23

BASIC RADIO CALLS

RECEIVING A CALL

MAKING A CALL Conventional Modes

Note: Do not interrupt another user. If the present

mode is programmed to receive PL, ensure that the mode is not in use by pressing the monitor button to listen for activity.

• If the mode-busy feature is enabled, a

blinking red LED on receive (PTT released) indicates that the mode is currently busy.

• If a mode is programmed for receive only,

any attempt to transmit on that mode will cause an invalid-mode tone to sound until the PTT switch is released.

Trunked Modes

Note: If you hear a busy signal (a low-frequency

“bah-bah-bah-bah”), release the PTT switch and wait for a call-back tone (sounds like “didi-dit”). When you hear the call-back tone, you have three seconds to press the PTT switch. This allows you to make another call without getting a busy signal.

1 Turn the radio on and select the desired

zone and mode (see Selecting a Zone and Mode on

page 20).

2 Your radio is now set to receive calls on the

selected mode.

1 Turn the radio on and select the desired

conventional zone and mode (see Selecting a Zone and Mode on page 20).

2 Press and hold the PTT switch on the side of

the radio and speak slowly and clearly into the microphone area. The red LED lights continuously when the radio is transmitting.

3 When you have finished talking, release the

PTT to listen.

1 Turn the radio on and select the desired

trunked zone and mode (see Selecting a Zone and Mode on

page 20).

2 Press and hold the PTT switch on the side of

the radio and speak slowly and clearly into the microphone area. The red LED lights when the radio is transmitting. When you have finished talking, release the PTT to listen.

20L01-A_PR_UG_MTX4500.book Page 21 Friday, April 13, 2007 2:47 PM

Page 24

BASIC RADIO CALLS

• If a continuous talk-prohibit tone is heard

when the PTT switch is pressed, transmission is not possible. The radio may be out of range.

Low-Battery Alert

Your radio emits an alert tone when a low-battery condition is detected.

Coded Squelch Operation

Tone Private-Line® (PL), Digital Private-Line™ (DPL), and carrier squelch operation are all available in your radio, on a per-mode basis. When in carrier squelch operation, all traffic on the mode is heard. When in PL or DPL operation, your radio responds to only those messages intended for you. When this feature is mode-slaved, PL, DPL, or carrier squelch is programmed to each mode.

Whenever the radio is operating in carrier squelch, the display shows

Variable RF Power Level (Selected Models Only)

Radios can have more than one power level. High power can be programmed on modes where high power is permitted, and low power can be programmed on all other modes. The high-/low-power feature can be selected via the menu keys.

FAILSOFT OPERATION (TRUNKED SYSTEMS ONLY)

The “failsoft” system ensures continual radio communications capability during a trunked system failure. Your radio automatically goes into failsoft operation if the central trunking controller fails for any reason. While in failsoft operation, your radio transmits and receives on a predetermined frequency on a conventional mode. When the trunked system returns to normal operation, the radio automatically leaves the failsoft operation and returns to trunked operation.

During failsoft operation,

1 You will hear a faint

“beeping” sound every ten seconds.

Alternates between

and

2 Your radio becomes unsquelched.

FAILSOFT

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 22 Friday, April 13, 2007 2:47 PM

Page 25

BASIC RADIO CALLS

MUTING THE KEYPAD TONES (FOR KEYPAD RADIOS ONLY)

The radio’s keypad tones, normally heard each time a keypad key is pressed, can be turned off (muted) or on (unmuted) at your discretion. To use the keypad mute feature

Note: Pressing or the PTT switch exits this

menu without changing the mute selection.

1 Press / until

MUTE is displayed.

2 Press ; (the

softkey below MUTE).

You will see the current mute state momentarily.

Then

ZONE

MUTE

CALL

TONES ON

TONES OFF

OFF

3 Press the softkey

below the desired mute state (on or off). The radio returns to the home display.

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 23 Friday, April 13, 2007 2:47 PM

Page 26

TRUNKED FEATURES

This section outlines the trunked features of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

VIEWING YOUR RADIO’S ID NUMBER

To View Your Radio’s ID Number

Note: If your radio has been so programmed, you

can press the call button for quick access to viewing your radio’s ID number. This takes you directly to Step

ENHANCED PRIVATE CALL OPERATION

The Enhanced Private Conversation feature not only allows you to have a conversation that is heard only by the two parties involved, but also enables you to determine whether the radio that you are calling is in service. The radio being called can also view the calling radio's ID number before answering.

You can then choose whether or not to leave your radio’s ID number (via a Call Alert page) with the radio you are calling so that you may be called back. Enhanced Private Conversation operation is similar to telephone operation.

Answering a Private Call

1 Press / until CALL is

displayed.

2 Press l (the softkey below CALL).

3 The display shows the

last ID number transmitted or received.

4 Press ,.

The display shows your radio’s ID number.

6 Press to return

the radio to the home display.

PLANT POLICE

ZONE

MUTE CALL

ID: 722588

MY ID:741317

PLANT POLICE

1 Upon receiving a Private

Conversation call, two alert tones sounds (repeating every five seconds for 20 seconds).

Alternates between

and

CALL RECEIVED

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 24 Friday, April 13, 2007 2:47 PM

Page 27

TRUNKED FEATURES

Note: If you press the PTT switch before you press

the call response button, the response is transmitted to everyone in the talkgroup (a dispatch mode operation).

• After answering a Private Call, the

caller’s ID number is stored in your radio as the “last ID number received”.

• If your radio is configured for Private Call

II, upon receiving a Private Conversation call, two alert tones sound, followed by the received voice.

Making a Private Call

There are four phases in making a private call, namely

• initiating a private call,

• entering the desired radio ID number,

• sending the radio ID number, and

• having the conversation and hanging-up.

2 The green LED and call received status

annunciator, F

, will blink indicating that a call

is being received. You have 20 seconds to answer the call before the radio automatically returns to the home display.

3 Press the call response button or the call

button.

4 The display shows the

incoming caller’s ID number, and the call received annunciator turns off.

5 After viewing the caller’s ID number, you can

decide to either talk privately (go to next step), or not answer the call by pressing the call response or call button to return to the home display.

6 If you decide to answer the call, press the PTT

switch.

7 The caller’s ID number

remains displayed for the duration of the call.

ID: 722588

8 When finished with conversation, press

or the call response button to hang up.

9 The radio returns to the

home display.

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 25 Friday, April 13, 2007 2:47 PM

Page 28

TRUNKED FEATURES

Initiating a Private Call

Entering the Desired Radio ID Number

If the last ID number called is the desired number, go directly to Step 5.

To Enter a New Number

Note: Exactly six digits must be entered for the

radio ID number. If fewer than six digits are entered, you hear a bad-keypress tone and the display shows “INVALID ENTRY” when

attempting to send the radio ID number. You will also hear a bad-keypress tone if you try to enter a seventh digit.

• Once you have started entering numbers,

the , key functions as a backspace key. Pressing it causes the last digit entered to be erased, and the cursor moves to the left. When the last digit is erased, an additional press of this key causes the last ID number transmitted or received to be displayed; pressing / shows the first member of the list.

To Enter a Number from the Call List

1 Press / until CALL is

displayed.

2 Press l (the softkey below CALL).

3 The display shows the

last ID number transmitted or received.

4a Enter the new six-digit ID number using the

keypad.

4b On the display, the old ID number disappears

and the new digits appear as they are being entered.

4c The cursor blinks indicating the location of the

next number to be entered.

ZONE

MUTE

CALL

ID: 722588

4a Press either , or /.

4b / takes you forward to the first or next

member of the list; , takes you backwards to the last or previous member of the list.

When at a member of the list, the display alternates between showing the member’s name and ID number.

Alternates between

and

CK TANG

ID: 784116

20L01-A_PR_UG_MTX4500.book Page 26 Friday, April 13, 2007 2:47 PM

Page 29

TRUNKED FEATURES

To Enter a Number from a Location in the Call List

Note: The last member of the list is also the “last ID

transmitted or received” at position “00” on the list.

• If you enter a location number that does

not exist (for example, “15”), the display shows “INVALID ENTRY”, and the radio sounds an invalid-keypress tone and returns to Step 4b of this procedure.

Sending the Radio ID Number

Note: If the radio you are calling is not in service,

you will not hear the ringing and the display will show “NO ACK”. Go to Step

10 to hang

up.

• If your radio is configured for Private Call II,

you will not hear the telephone type ringing. Instead you are able to proceed to talk to the Called party.

4a Press either , or / to enter the call

list.

4b Enter the first digit of the location number. If

there are fewer than 10 members in the list, go directly to Step 4e.

4c If there are 10 or more members in the list,

the display shows “ID LOC#X_” (where X is the first digit). The cursor blinks to show the location of the second digit.

4d Enter the second digit of the location number.

4e The radio goes to that

position in the list. The display alternates between showing the member’s name and ID number.

Alternates between

and

CK TANG

ID: 784116

5 Press the PTT switch to transmit the ID

number.

6 If the radio you are calling is on the air, you will

hear a telephone-type ringing for 20 seconds, or until the called radio answers the call.

7 If the party you are

calling does not answer the call within twenty seconds, the telephone ringing stops and an alert tone sounds.

At this point you can either send a Call Alert™ page, or go to Step 10 to hang up.

8 If the party you are calling answers the call,

you will hear his/her voice.

NO ANSWER

20L01-A_PR_UG_MTX4500.book Page 27 Friday, April 13, 2007 2:47 PM

Page 30

TRUNKED FEATURES

Having the Conversation and Hanging-up

Note: Once engaged in a private conversation, if

the radio is left idle for more than one minute, a momentary warning alert sounds every six seconds to remind you that dispatch calls are not being heard. After two minutes, a permanent invalid mode tone sounds.

Leaving a Call Alert Page

9 Press the PTT switch to have a Private

Conversation with the called person.

10 When finished with your conversation, or if the

radio you called does not answer or is not in service, press

to hang up.

11 The radio returns to the

home display.

PLANT POLICE

1 If the party you want to have a Private Call

does not answer the call within twenty seconds, you can choose to leave a Call Alert™ page. This leaves your radio’s ID number with the called radio so you can be called back later.

2 Press the PTT switch to send the Call Alert

page. You will hear five beeps, indicating that the system has received your ID number and the radio you are calling is on the air.

3 Press .

4 The radio returns to the

home display.

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 28 Friday, April 13, 2007 2:47 PM

Page 31

TRUNKED FEATURES

CALL ALERT OPERATION Answering a Call Alert Page with a Group

Call

Note: When you receive a Call Alert page, you can

enter Private Call mode and call the paging radio using the latest ID received.

Making a Call Alert

There are three phases in making a call alert, namely

• initiating a call alert,

• entering the radio ID number that you wish to page, and

• sending the call alert.

Initiating a Call Alert

Note: The same list is shared by both Call Alert and

Private Conversation features.

• If your radio has been so programmed, you

can press the page button for quick access to the Call Alert feature. This takes you directly to Step 3.

1 Upon receiving a Call Alert page, four alert

tones sound (repeats every 5 seconds).

2 The green LED lights and the Call Received

annunciator, F, blinks indicating a call is received.

3 Press the PTT switch to answer the page.

4 The display shows the

current talkgroup. The audible alert, LED and call received annunciator turns off.

5 The ID number of the radio that paged you is

stored as “the last ID number received.”

6 Have your conversation in the normal manner;

all members of your talkgroup will hear your response. Press the PTT switch to talk; release the switch to listen.

FIRE DEPT

1 Press / until PAGE is

displayed.

2 Press l (the softkey below PAGE).

3 The display shows the

last ID number transmitted or received.

PAGE

PHON

VIEW

ID: 722588

20L01-A_PR_UG_MTX4500.book Page 29 Friday, April 13, 2007 2:47 PM

Page 32

TRUNKED FEATURES

Entering the Radio ID Number that you wish to Page

If the last ID number called or received is the desired number, go directly to Step 5.

To Enter a New Number

Note: Exactly six digits must be entered for the

radio ID number. If fewer than six digits are entered, you will hear a bad-keypress tone when attempting to send the radio ID number. You will also hear a bad-keypress tone if you try to enter a seventh digit.

• Once you have started entering numbers,

received to be displayed; pressing / shows the first member of the list.

To Enter a Number from the Call List

To Enter a Number from a Location in the Call List

4a Enter the new six-digit ID number using the

keypad.

4b On the display, the old ID number disappears

and the new digits appear as they are being entered.

4c The cursor blinks indicating the location of the

next number to be entered.

4a Press either , or /.

4b / takes you forward to the first or next

member of the list; , takes you backwards to the last or previous member of the list.

When at a member of the list, the display alternates between showing the member’s name and ID number.

Alternates between

and

4a Press either , or / to enter the call

list.

4b Enter the first digit of the location number. If

there are fewer than 10 members in the list, go directly to Step 4e.

4c If there are 10 or more members in the list,

the display shows “ID LOC#X_” (where X is the first digit). The cursor blinks to show the location of the second digit.

CK TANG

ID: 784116

20L01-A_PR_UG_MTX4500.book Page 30 Friday, April 13, 2007 2:47 PM

Page 33

TRUNKED FEATURES

Note: The last member of the list is also the “last ID

transmitted or received” at position “00” on the list.

• If you enter a location number that does

not exist (for example, “15”), the display shows “INVALID ENTRY”, and the radio sounds an invalid-keypress tone and returns to Step 4b of this procedure.

Sending the Call Alert

If the Page is Unsuccessful

If the Page is Successful

4d Enter the second digit of the location number.

4e The radio goes to that

position in the list. The display alternates between showing the member’s name and ID number.

Alternates between

and

5 Press the PTT switch to transmit the ID

number.

CK TANG

ID: 784116

6a If you hear one beep, the ID number has

been received by the system, but the radio you are paging is not on the air; your radio remains in the Call Alert mode.

If after six seconds the called radio fails to acknowledge the alert, a low-pitched alert tone sounds and the display changes to “NO

ACKNOWLEDGE”.

6b Press the PTT switch to send the ID number

again, or press to hang up and return to the home display.

6a If you hear five beeps, the ID number has

been received by the system, and the radio you are paging is on the air and has received your page.

6b The radio automatically

returns to the home display

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 31 Friday, April 13, 2007 2:47 PM

Page 34

TRUNKED FEATURES

AUTOMATIC MULTIPLE SITE SELECTION (AMSS)

The automatic multiple site selection (AMSS) feature extends communications beyond the reach of a single trunked site. In a system where wide-area coverage is required, multiple trunking sites are used.

AMSS automatically switches the radio to a different site when the current-site signal becomes too weak. Typically, this happens when the radio is moved out of the range of one site and into the range of another. Under normal conditions, this switching is invisible to the user.

Viewing the Current Site

Forcing a Site Change

Locking and Unlocking a Site

1 Press the search button.

2 If the radio is locked on a

site, the display shows the current site.

3 If the radio is scanning

for a new site, the display shows “SCANNING” until it locks on a new site.

Then it shows the number of the new site.

SITE 4

SCANNING SITE

SITE 7

1 Press and hold down the search button to

force the change to a new site.

2 You will hear a tone

while the radio scans for a new site.

3 The radio automatically

returns to the home display.

1 Press / until SITE is

displayed.

2 Press l (the softkey below SITE).

3 The current lock state is

momentarily displayed.

4 The display changes to

5 Press the key below the desired lock state.

6 The radio automatically

returns to the home display.

SCANNING SITE

PLANT POLICE

SITE

PAGE

CALL

SITE LOCKED

SITE UNLOCKED

LOCK

UNLK

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 32 Friday, April 13, 2007 2:47 PM

Page 35

CONVENTIONAL

FEATURES

CONVENTIONAL FEATURES

This section outlines the conventional features of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

REPEAT/DIRECT

The repeat/direct feature allows you to bypass the repeater and talk directly to another portable radio. This is known as DIRECT operation. The transmit frequency is the same as the receive frequency.

• In REPEAT operation, you talk through the repeater, which increases the radio's operating range. The transmit frequency is not the same as the receive frequency.

• If the repeat/direct feature is programmed to a mode, that mode operates on either direct or repeat operation.

• If the repeat/direct feature is programmed to the keypad, you can change the repeat/direct setting by doing the following.

PLANT POLICE

1 Press / until DIR is

displayed.

2 Press l (the softkey below DIR).

3 The current talkaround

state appears on the display for a few seconds.

4 Then, the display

prompts for the new state.

5 Press l below the desired talkaround

state: repeat (RPTR) or direct (DIR).

6 The radio returns to the

home display.

DIR

PWR

PROG

REPEATER MODE

DIRECT MODE

DIR

RPTR

PLANT POLICE

Page 36

CONVENTIONAL

FEATURES

SMART PTT

Smart PTT is a per-mode feature that gives the system manager better control of radio operators. When smart PTT is enabled in your radio, you cannot transmit on an active mode. Three radio-wide variations of smart PTT are available.

• Transmit Inhibit on Busy Mode — You are

prevented from transmitting if any activity is detected on the mode.

• Transmit Inhibit on Busy Mode with Wrong Squelch Code — You are prevented from transmitting on an active mode with a squelch code other than your own. If the PL code is the same as yours, you are allowed to transmit.

• Quick-Key Override — This feature can work in

conjunction with either of the two above variations. This feature allows you to override the transmit-inhibit state by quick-keying (two PTT presses within a programmable period – the default is one second – of each other) the radio.

Note: If you try to transmit (press the PTT) on a

smart PTT mode that is busy, a continuous alert tone is generated until the PTT is released; the transmission is inhibited.

• The red LED blinks when the radio is

receiving indicating that the mode is busy.

20L01-A_PR_UG_MTX4500.book Page 34 Friday, April 13, 2007 2:47 PM

Page 37

SCAN

This section outlines the scan functions of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

SCAN OPERATION

The scan feature allows you to monitor activity on different conventional or trunked modes by scanning a scan list of modes. This list can be programmed with the Customer Programming Software (CPS) or user programmable.

Three types of scan operation are available depending on radio model.

Your radio may support both priority and non-priority scanning. With priority scanning enabled, a scan list can have one mode assigned as the first priority mode, and a second as the second priority mode.

Automatic scanning (autoscan) can be programmed through the CPS. If autoscan is enabled for a mode, your radio begins scanning, using the mode’s scan list, whenever you select that mode. The radio continues autoscanning until you select a mode that does not have autoscan enabled.

Turning Scan On or Off with the Keypad (For Keypad Radios Only)

Trunking Priority Monitor

Comprises modes that are all from the same trunked system.

Conventional Comprises conventional-only modes.

Talkgroup Scan

Comprises conventional modes and trunked modes from more than one trunking system. Priority operation is NOT available in this type of list.

PLANT POLICE

1 Press / until

SCAN is displayed.

2 Press ; (the

softkey below SCAN).

You will see the current scan state momentarily.

Then

PHON

SCAN

CALL

SCAN ON

SCAN OFF

OFF

20L01-A_PR_UG_MTX4500.book Page 35 Friday, April 13, 2007 2:47 PM

Page 38

SCAN

Note: The scan status annunciator, G, is

displayed when the scan operation is active. It is removed from the display when the scan operation is terminated.

Deleting Nuisance Modes

When the radio scans to a mode you do not wish to monitor (nuisance mode), you can temporarily delete that mode from the scan list.

Note: Priority modes cannot be deleted.

Viewing a Scan List (For Keypad Radios Only)

The view scan list feature allows you to view the members of the scan list associated with the currently selected mode.

To view a scan list

3 Press the softkey

below the desired scan state (on or off). The radio returns to the home display.

1 When your radio is locked on the mode to be

deleted, press the nuisance-mode delete button (programmed via the CPS).

2 A valid-keypress chirp is heard, indicating

that the mode has been deleted.

3 The radio continues scanning the remaining

modes in the list.

4 To resume scanning the deleted mode, you

must leave and reenter scan operation.

PLANT POLICE

1 Press / until

VIEW is displayed.

2 Press l (the

softkey below VIEW).

3 Press ; (the

softkey below SCAN). The display shows the first member of the scan list.

For example

4 Every subsequent press of / scrolls

through subsequent members of the scan list.

5 To leave the scan list feature, press the

HOME key, or the PTT switch, or turn the mode selector knob.

6 The radio returns to

the home display.

PAGE

STS

VIEW

PHON

SCAN

CALL

FIRE DEPT

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 36 Friday, April 13, 2007 2:47 PM

Page 39

SCAN

Note: The programming-mode annunciator, K, is

displayed while list view mode is active.

• The scan status annunciator, G, appears,

indicating that a scan list is being viewed.

• The dot of the priority scan annunciator,

H, blinks if the current displayed member of the scan list is a priority 1 mode, and is solid the current displayed member of the scan list is a priority 2 mode.

Programming a Scan List (For Keypad Radios Only)

The program scan list feature allows you to program the members of the scan list associated with the currently selected mode.

To program a scan list

Note: The programming-mode annunciator, K,

blinks while program mode is active.

• The scan status annunciator, G, appears,

indicating that a scan list is being viewed.

• The dot of the priority scan annunciator,

H, blinks if the current displayed member of the scan list is a priority 1 mode, and is solid the current displayed member of the scan list is a priority 2 mode.

1 Press / until

PROG is displayed.

2 Press l (the

softkey below PROG).

3 Press l (the

softkey below SCAN). The display shows the current mode selected.

For example

PROG

SCAN

PHON

CALL

FIRE DEPT

4 Use the mode selector knob to select the

required talkgroup zone.

5 Press , or / to select the required

zone. If the scan status annunciator G is displayed, the mode is part of the scan list.

6 Press the select key to change the scan

mode (See Scan Modes on page 38).

7 After making all the changes, select the

required operating mode.

8 Press the HOME key, or the PTT switch, or

turn the mode selector knob to commit all the changes made.

20L01-A_PR_UG_MTX4500.book Page 37 Friday, April 13, 2007 2:47 PM

Page 40

SCAN

Scan Modes

Note: There can only be ONE Priority 1 member

and ONE Priority 2 member in a scan list. Thus, if there is already a Priority 1 member in the scan list, changing another member’s mode to Priority 1, would automatically cause the previous member’s mode to be changed to a Scan Member.

This same behavior is also seen when programming the Priority 2 member.

Initial Scan Mode of Member

Number of Times the Select Key is Pressed

1 2 3 4

Priority 2* Priority 1*

Non-Scan Member

Scan Member Priority 2*

Priority 1*

Non-Scan Member

Scan Member Priority 2* Priority 1*

Non-Scan Member

Scan Member Priority 2* Priority 1*

Non-Scan Member

Scan Member Priority 2* Priority 1*

Non-Scan Member

Scan Member

* Priority options are only available if enabled.

When programming the scan list, each member can be given one of several scan modes. The following table lists the scan mode cycle activated by subsequent presses of the select key.

20L01-A_PR_UG_MTX4500.book Page 38 Friday, April 13, 2007 2:47 PM

Page 41

PROGRAMMING THE

RADIO

PROGRAMMING THE RADIO

This section outlines the programming functions of your radio, and is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

Programming the Telephone List Numbers

This feature lets you use the radio’s keypad to change the telephone numbers assigned to any of the telephone list members. Each phone number can only have up to 16 digits.

To change the telephone list

1 Press / until PROG

is displayed.

2 Press l (the softkey

below PROG).

3 Press ; (the softkey

below PHON). The display shows the first programmable member of the telephone list.

PLANT POLICE

PROG

SCAN

PHON

CALL

FIRE DEPT

4 Press / or ,,

—or—

Use the keypad to enter the desired member’s position number (1 to 19) to view the other members of the telephone list.

5 When you stop on a

member of the list, the display alternates between showing the member’s name and telephone number.

Alternates between

and

6 Press the select key to enter edit mode.

7 A short press enables

the editing of the telephone number. The display shows the current member’s telephone number.

8 A long press enables the

editing of the member’s name. The display shows the current member’s name.

POLICE DEPT

5556213

POLICE DEPT

Page 42

PROGRAMMING THE

RADIO

Note: The programming-mode annunciator, K,

blinks while program mode is active.

• In the edit mode, the , key functions as

a backspace key. Pressing it erases the previous digit, and the cursor moves to the

left. When the last digit on the display has been erased, additional presses of this key or the / key will cause you to leave the edit mode without making any changes.

• When the maximum of 16 digits in an entry

for the telephone list is reached, the cursor disappears. If you try to add any more digits, you will hear an invalid (bad) keypress alert tone.

Programming the Call List

This feature lets you use the radio’s keypad to change the radio ID numbers assigned to the call list used by the trunked Private Conversation™ and Call Alert™ features. Similarly, in Conventional Mode, you may change the Call List used by StatAlert Selective Call and Call Alert.

To change the call list radio ID numbers

9 Use any of the alphanumeric keys to make the

changes. The blinking cursor indicates the position of the next number to be added. If you require a pause in the phone dialing sequence (to allow for a delay), you can do so by first pressing the “*” key, followed by pressing the “#” key. The display will show a “P” for pause.

10 When you have finished changing the

telephone number, press the select key again. The change is saved in the radio’s memory.

11 You are returned to Step

5. The display will again alternate between the member’s name and telephone number. You can now change additional numbers.

Alternates between

and

12 When you have finished making changes,

press to exit program mode.

13 The radio returns to the

home display.

POLICE DEPT

5556445

PLANT POLICE

1 Press / until PROG is

displayed.

2 Press l (the softkey

below PROG).

3 Press l (the softkey

below CALL). The display shows the first programmable member of the call list.

DIR

SCAN

PROG

SCAN

PHON

CALL

SK TAN

Page 43

PROGRAMMING THE

RADIO

Note: The programming-mode annunciator, K,

blinks while program mode is active.

• In the edit mode, the , key functions as

a backspace key. Pressing it erases the previous digit, and the cursor moves to the left. When the last digit on the display has been erased, additional presses of this key or the / key will cause you to leave the edit mode without making any changes.

• When the maximum number of digits for

the radio ID is reached, the cursor disappears. If you try to add any more digits, you will hear an invalid (bad) keypress alert tone.

4 Press / or ,,

—or—

Use the keypad to enter the desired member’s position number (1 to 19) to view the other members of the call list.

5 When you stop on a

member of the list, the display alternates between showing the member’s name and radio ID number.

Alternates between

and

6 Press the select key to enter edit mode.

7 A short press enables the

editing of the radio ID. The display shows the current member’s radio ID number.

8 A long press enables the

editing of the member’s name. The display shows the current member’s name.

9 Use any of the alphanumeric keys to make the

changes. The blinking cursor indicates the position of the next number to be added.

CT CHAN

ID: 753951

CT CHAN

10 When you have finished changing the number,

press the select key again. The change is saved in the radio’s memory.

11 You are returned to Step

5. The display will again alternate between the member’s name and radio ID number. You can now change additional numbers.

Alternates between

and

12 When you have finished making changes,

press to exit program mode.

13 The radio returns to the

home display.

CT CHAN

ID: 753853

PLANT POLICE

Page 44

TELEPHONE

OPERATION

TELEPHONE OPERATION

This section outlines the telephone operations of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display. The telephone feature allows you to use your radio

similar to a standard telephone. When you are dialing from the keypad, your radio

may be programmed with either buffered dial (you enter all digits and press the PTT before the digits are sent out) or live dial (each digit is sent out as it is pressed).

Answering a Telephone Call

Note: The call received status annunciator, F,

blinks when you receive a call, but is not displayed when you answer the call.

Making a Telephone Call (For Model II Radios Only)

There are three phases in making a phone call, namely

• accessing the telephone system,

• sending the telephone number,

• having the conversation and hanging-up.

Accessing the Telephone System

1 When a telephone call is

being received, you will hear telephone-type ringing.

Alternates between

and

2 Press the

preprogrammed phone button or call response button to answer the call.

PLANT POLICE

PHONE CALL

3 Carry on with your conversation in the normal

manner. Press the PTT switch to talk; release the PTT to listen.

4 When you have finished your conversation,

press or the phone button to hang up.

5 The radio returns to the

home display.

1 Press / until PHON

is displayed.

2 Press l (the softkey below PHON).

3 Your radio attempts to access the telephone

system.

PLANT POLICE

MSG

SCAN

PHON

20L01-A_PR_UG_MTX4500.book Page 42 Friday, April 13, 2007 2:47 PM

Page 45

TELEPHONE

OPERATION

Sending the Telephone Number

Sending the Telephone Number Using the Keypad

Sending the Telephone Number Using a Number on the Telephone List

4 If you connect successfully, you will hear a dial

tone.

5 The display shows the

last number dialed.

6a The number can now be entered from the

keypad, using any of the numeric (0 – 9) keys, and the “*” and “#” keys. The cursor blinks to indicate the location of the next digit to be entered. A pause can be entered in the telephone number by first pressing the “*” key, then the “#” key (Buffered dial only – the pause is shown on the display as a “P”).

6b If your radio is programmed for “live dial,”

each digit is sent out as its key is pressed.

—or—

If your radio is programmed for “buffered dial,” each digit is temporarily stored as you enter them. After entering the number, press the PTT switch to send out the number.

6c The telephone number will be sent out; you

will hear tones as they are sent. If you hear a busy signal, go to Step 8 for hang-up procedure.

5551135

6a Press , or /, to enter the telephone

list. / takes you forward to the next member of the list; , takes you backwards to the previous member of the list.

6b Stop at the member you wish to call.

6c The display alternates

between showing the member’s name and telephone number.

Alternates between

and

6d Press the PTT button.

6e The telephone number

will be sent out; you will hear tones as they are sent.

6f If you hear a busy signal, go to Step 8 for

hang-up procedure.

POLICE DEPT

5556445

POLICE DEPT

20L01-A_PR_UG_MTX4500.book Page 43 Friday, April 13, 2007 2:47 PM

Page 46

TELEPHONE

OPERATION

Sending the Telephone Number Using a Location in the Telephone List

Having the Conversation and Hanging Up

Note: You can press the pre-programmed phone

button for quick access to the telephone call feature. This takes you directly to Step

• The “PLEASE WAIT” message is a timed

message. If you cannot access the telephone system (no dial tone heard),

press key or the phone button to hang up, and start again at Step 1 of this

procedure.

• If you are out of range of the trunked

system or the phone interconnect is out of service, “NO PHONE” is displayed and a continuous low-pitched tone sounds.

• If the trunked phone interconnect is in use, a busy tone sounds and “PHONE BUSY” is displayed.

6a Press , or /, to enter the telephone

list.

6b Enter the location (any preprogrammed

location from 1 through 19) of the number you wish to call.

6c The radio goes to the selected location.

6d The display alternates

between showing the member’s name and telephone number.

Alternates between

and

6e Press the PTT button.

6f The telephone number

will be sent out; you will hear tones as they are sent.

6g If you hear a busy signal, go to Step 8 for

hang-up procedure.

POLICE DEPT

5556445

POLICE DEPT

7 If call is answered, communicate in the normal

manner. Press the PTT switch to talk; release the PTT to listen.

8 When finished with your conversation, or if the

number you called is busy or does not answer, press

or the phone button to send the

hang-up code.

9 The radio returns to the

home display.

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 44 Friday, April 13, 2007 2:47 PM

Page 47

TELEPHONE

OPERATION

• When the maximum number of digits have

been entered (buffered dial only), the cursor disappears.

• In the edit mode, the , key functions as

a backspace key. Pressing this key erases the last digit entered, and moves the cursor to the left. When the last digit on the display is erased, additional presses of this key causes the last member of the preprogrammed telephone list to be displayed; pressing the / key displays the first member of the list.

• After reaching the number you are calling,

you may need to dial an extension number before you can reach your party. Here, enter the extension number from the keypad or (if so programmed) use the arrow keys to find the extension number in the telephone list. If you have live dial, the number is sent as the keys are pressed. If you have buffered dial, press the PTT switch again to send out the extension number.

• Motorola trunked systems and many

conventional telephone patches generate a high-pitched go-ahead tone when the radio's PTT switch is released. This is heard by the land-line party and is an indicator to begin talking.

• The conventional telephone feature allows

you to use your conventional radio similar to a standard telephone. To make a call through the telephone system, your radio must send access and hangup codes to the system. Unless otherwise indicated, the conventional telephone sections in this manual assume that the access and hangup codes have been programmed into the radio by the RSS. These codes are then automatically transmitted.

20L01-A_PR_UG_MTX4500.book Page 45 Friday, April 13, 2007 2:47 PM

Page 48

SPECIAL FEATURES

This section outlines some of the special features that can be configured for your radio. However, not all models come equipped with these features.

All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

EMERGENCY OPERATION

Pressing the top emergency button (for radios with emergency operation) sends out an emergency signal, which takes precedence over any other signalling activity in progress. This emergency signal can take two forms: emergency alarm and emergency call. Your radio can have either or both signal types enabled.

•The emergency alarm feature alerts the

dispatcher, who is using a special terminal, to an emergency condition and identifies the unit sending the emergency signal.

•The emergency call (radios with trunked

emergency operation only) is a type of dispatch operation which gives your radio priority access. Emergency call is programmable for either tactical or non-tactical operation. Tactical

emergency operation places the call to the currently selected mode; non-tactical operation places the call to a predetermined emergency mode.

“Emergency” signals a critical situation. It should

NEVER be used for any other reason.

Sending an Emergency Alarm

PLANT POLICE

Press and hold the emergency button (the length of button press is programmable by the CPS).

Alternates between

and

2 A short, medium-pitched emergency tone

sounds, indicating entry into emergency operation.

3 When the trunked emergency alarm is

acknowledged by the central controller, the radio sounds five beeps and the alarm ends.

4 The radio returns to normal operation or, if

enabled in your radio (trunked emergency call systems only), enters into emergency call operation.

5 While in emergency call operation,

subsequent presses of the emergency button reinitiates the emergency sequence.

EMERGENCY

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 46 Friday, April 13, 2007 2:47 PM

Page 49

SPECIAL FEATURES

Sending a Silent Emergency Alarm

Canceling an Emergency Alarm

The alarm can also be canceled (without sounding the emergency-exit tone) by:

• pressing the PTT switch (see following note),

• turning the radio off, or

• receiving an acknowledge from the dispatcher.

Note: Pressing the PTT switch while the radio is in

emergency alarm operation places the radio in emergency call operation if emergency call is enabled.

Sending an Emergency Call

Note: The mode you use during an emergency is

controlled by whether your radio is programmed for tactical or non-tactical operation. If tactical, you will talk to the mode you selected before entering emergency call; if non-tactical, you will talk to a preprogrammed emergency mode.

1 In radios with the silent emergency alarm

option enabled, pressing the emergency button sends an emergency signal to the dispatcher.

2 During the emergency alarm procedure: the

LED will not light, tones will not sound, and the display will not change.

3 The audio is muted (turned off), and remains

so until you exit the emergency state.

1 Press the emergency button for more than 11/2

seconds (programmable by the CPS).

2 A medium-pitched emergency-exit tone

sounds until the button is released and the radio returns to normal operation.

1 Press the emergency

button.

Alternates between

and

2 A short, medium-pitched emergency tone

sounds.

3 Press the PTT switch requesting a priority

mode assignment in the trunked system.

4 While the radio is in emergency call operation,

it operates in the usual dispatch manner.

EMERGENCY

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 47 Friday, April 13, 2007 2:47 PM

Page 50

SPECIAL FEATURES

• If you change modes while in emergency

call operation, the emergency call is moved and continued on the new mode.

Ending an Emergency Call

It is important that you exit the emergency call mode when you have finished your emergency call.

Emergency with Voice to Follow

This feature (aka Hot Microphone) places your radio in a transmit mode for a preprogrammed period of time (programmable by CPS) after the emergency alarm is activated. During this time period, voice transmissions can be made without pressing the PTT.

After this transmit time has expired, the unit reverts back to receive mode. Normal operation resumes, and the user is required to press PTT for any further transmissions on that emergency channel.

DYNAMIC REGROUPING

The dynamic regrouping feature allows the dispatcher to temporarily reassign selected radios, operating in the same or different trunked modes, to a single special mode so that they can communicate with each other. This feature, enabled in each radio via the CPS, is typically used during special operations. When your radio has been dynamically regrouped, you will hear a distinct “gurgle” tone.

Mode Selection

You will not notice whether your radio has this feature enabled until a dynamic regrouping is sent by the dispatcher. If you turn your radio's mode selector knob to the dynamic regrouping position without being dynamically regrouped, an invalid-mode tone is heard.

You can select the dynamic regrouping position using the menu on the display (Model II radios only) or using the mode selector knob. To do this with the mode selector knob

1 Press the emergency button for more than 11/2

seconds (programmable by the CPS).

2 You will hear a medium-pitched emergency-

exit tone until the emergency button is released, and the radio returns to normal operation.

1 When your radio is dynamically regrouped,

you will hear a “gurgle” tone.

2 Your radio is automatically switched to the

dynamic regrouping mode. The display shows the name assigned to the dynamic regrouping mode.

20L01-A_PR_UG_MTX4500.book Page 48 Friday, April 13, 2007 2:47 PM

Page 51

SPECIAL FEATURES

Note: Until you select the correct mode position,

you will hear a gurgle tone each time you press the PTT switch, reminding you that you are transmitting on the dynamic regrouping mode, not the mode indicated by the position of the mode selector knob.

Select Enable and Disable

The dispatcher may classify regrouped radios into either of two categories: select enabled, and select disabled.

Scan, Phone, and Private Conversation cannot be selected while the radio is select disabled.

3 Turn the mode selector knob to the dynamic

regrouping position to transmit on the dynamic regrouping mode.

4 Talk and listen as usual.

5 When the dynamic regrouping is canceled by

the dispatcher: a. If the mode selector knob is in the dynamic regrouping position, an invalid-mode tone is heard until a normal mode is selected. b. If the mode selector knob is in any other mode position, the radio transmits in the selected mode.

Select Enabled

These radios are free to make mode changes to any available mode, including the dynamic regrouping mode.

Select Disabled

These radios cannot change modes, since the dispatcher has specifically chosen to force the radio to remain in the dynamic mode.

20L01-A_PR_UG_MTX4500.book Page 49 Friday, April 13, 2007 2:47 PM

Page 52

SMARTZONE

OPERATION

SMARTZONE OPERATION

This section outlines the SmartZone

operations of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

BENEFITS OF SMARTZONE

Radios that operate in a SmartZone system enjoy the benefits that SmartZone brings over AMSS operation. Like AMSS, SmartZone is a wide-area coverage system that allows multiple sites to be operational in the system. SmartZone brings several enhancements over AMSS operation, as in the following.

1. Dynamic Site Assignment Allows the zone controller to dynamically assign

channels at sites where required, as opposed to bringing up channels at all of the sites as AMSS systems do.

2. Variable Density Sites SmartZone allows sites to have varying numbers

of channel resources to accommodate low-density areas as well as high-density areas.

PLANT POLICE

3. Automatic Site Registration/De-registration SmartZone radios automatically send in their unit

IDs and current mode selections upon power up, power down, site switches, mode changes, and when they exit emergency operation. This allows the zone controller to know where the radio is at all times, and what mode the radio has selected.

4. Critical Site Assignment One or more sites can be designated as critical

sites. This instructs the zone controller to ensure that every site designated as a critical site must have available channel resources, before a channel is given to a radio wishing to be identified as a critical site user. Otherwise, a busy is sent to the unit.

5. Busy Override This feature allows a SmartZone radio to send a

busy override request if a busy is issued. The zone controller sends a grant even though not all of the sites may have available channel resources.

20L01-A_PR_UG_MTX4500.book Page 50 Friday, April 13, 2007 2:47 PM

Page 53

SMARTZONE

OPERATION

Site Switching in SmartZone

Site Switching in SmartZone mainly uses signal strength to determine whether or not to switch sites. Other factors used are the radio's preferred site selection, and whether the radio is site locked or not. Because the radio knows the site ID, active control mode, and the signal strengths of its adjacent sites, the radio is capable of quickly switching sites.

6. Enhanced Automatic Site Switching SmartZone radios use RSSI (received signal

strength indication) to determine if the radio should switch to another site. This is transparent to the user. In addition, the zone controller continuously transmits adjacent site information to the radios, so that the radio, at any time, is able to quickly switch to the next site that has the highest RSSI rating. This is an enhancement over AMSS systems.

7. Preferred Site SmartZone radios can program certain sites to be

always preferred, most preferred, or least preferred. This gives the user the flexibility to keep a radio on a particular site, regardless of the presence of a stronger signal from an adjacent site. This also forces the radio to always look for its preferred site and use it whenever possible.

8. Site Trunking If the zone controller loses communication with

any site, that site reverts to what is known as “site trunking.” While in this condition, radios are still able to operate in the trunking mode, but trunking operations are limited to the site only.

9. Enhanced Failsoft Operation If a site experiences a complete failure, it reverts

to failsoft operation like today's SMARTNET system. A SmartZone radio, however, can be programmed to automatically migrate to the lowest failsoft frequency programmed in its list of 32 control modes. The radio periodically scans the control mode to check for the presence of a valid control mode (in case the radio roamed into a site which is trunking).

20L01-A_PR_UG_MTX4500.book Page 51 Friday, April 13, 2007 2:47 PM

Page 54

SMARTZONE

OPERATION

Viewing the Current Site Forcing a Site Change

Locking and Unlocking a Site

As in an AMSS radio, you can force the radio to stay locked onto a site, regardless of whether the signal level of an adjacent site is higher or not. Of course, locking a radio onto a particular site defeats the automatic site switching mechanisms of the radio. However, you can still force the radio to scan to another site while site locked. The radio automatically becomes site locked to the next site it finds. Refer to Locking and Unlocking a Site on

page 32 to change

the radio’s locked state.

1 Press the search button.

a If the radio is presently locked on a site, the

display shows either the name of the current site or the site number.

b If the radio is scanning

for a new site, the display shows

until it locks onto a new site. This is a timed display which disappears after a few seconds.

c If the radio has not

received a site ID, the radio displays

until either the display times out or the radio receives the site ID.

SCANNING SITE

SITE XX

1 Press and hold down the search button to

force the change to a new site.

2 You will hear a tone and

the display shows

while the radio scans for a new site.

3 When a new site is found, the new site's name

is momentarily displayed if it is known,

otherwise

SCANNING SITE

SITE XX

20L01-A_PR_UG_MTX4500.book Page 52 Friday, April 13, 2007 2:47 PM

Page 55

SMARTZONE

OPERATION

Preferred Site Selection

SmartZone radios can have up to eight sites that are individually set as either always preferred, most preferred, or least preferred. The default value is no preference. This feature is programmed via the CPS.

Busy Override

With the introduction of dynamic site assignment, critical site, and critical user concepts in SmartZone, the busy processing rules were changed to allow users to communicate with some of the trunked mode members instead of waiting for all trunked mode members in all sites to be available. A busy override request can be made to request for the grant, even though one or more non-critical states are busy. Busy override is not a radio codeplug option but is enabled or disabled via the SmartZone manager.

Always-Preferred Site

A SmartZone radio always attempts to stay on this site whenever possible unless the receive signal strength indication (RSSI) level falls below the unacceptable level. The radio periodically checks the RSSI levels of its preferred site(s) to ensure that it always operates on the best preferred site (more than one preferred site can be enabled).

Most-Preferred Site

A site marked in this fashion is one level of preference below always preferred. The radio attempts to remain on this site unless an always- preferred site is determined to have either the same or a higher RSSI level. The radio always determines the best most-preferred site and switches to it whenever possible.

Non-Preferred Site

A radio operating in this site switches sites if an always preferred or most-preferred adjacent site with the same or higher RSSI level is discovered. The radio always determines the best non- preferred site and switch to it whenever possible.

Least-Preferred Site

A radio operating in this site switches sites if any of the above site rankings for any adjacent sites are discovered and their RSSI levels are at least at the acceptable range. The unit always determines the best least-preferred site and switch to it whenever possible.

20L01-A_PR_UG_MTX4500.book Page 53 Friday, April 13, 2007 2:47 PM

Page 56

SMARTZONE

OPERATION

After you have requested a mode by pressing the PTT, and have received a busy indication

Site Trunking

Site trunking occurs when a site is no longer able to participate in wide-area calls controlled by the zone controller. Radios operating in site trunking can only communicate with other radios at that site. All trunking features are still available. The radio will always be looking for a wide-area trunking site to lock onto if it roams into range of one.

1 Release the PTT and press it again. A busy

indication will be received if it is still busy.

2 Keep the PTT switch pressed for the amount

of time specified in the codeplug for busy override delay time (typically about three seconds, but can range from two to six seconds).

3 After the timer times out, if the PTT is still

pressed, the busy override request is sent.

4 A programmable busy override chirp

acknowledgement is heard.

5 If a grant is received, you should note that not

all of the members of the mode are engaged in the call. You will not be able to determine this. More sites may join the call, however, if members become available at these sites and the original call is still active.

When a site goes into site trunking, the radio receives this indication and displays.

The display alternates between the current trunked mode and the site trunking display for as long as the radio remains in site trunking.

The radio is not considered in site trunking if: a. The zone controller determines that the site

should no longer be in site trunking and the

radio receives this indication, or b. the radio is out of range, or c. the radio enters failsoft operation.

SITE TRUNKING

20L01-A_PR_UG_MTX4500.book Page 54 Friday, April 13, 2007 2:47 PM

Page 57

STAT-ALERT

FEATURES

STAT-ALERT FEATURES

This section outlines the Stat-Alert features of your radio. Stat-Alert is an option which you can enable for your radio. Please see your dealers for more information.

All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below

is used to indicate the radio’s home display.

VIEWING YOUR RADIO’S ID NUMBER

To View Your Radio’s ID Number

Note: If your radio has been so programmed, you

can press the call button for quick access to viewing your radio’s ID number. This takes you directly to Step

STAT-ALERT VOICE SELECTIVE CALL OPERATION

This feature provides a convenient way for a dispatcher to voice page an individual or group. Voice selective call decode also eliminates the need for you to listen to traffic that is of no concern to you. This is a per-radio feature, enabled on a per-mode basis, and available as individual call or group call.

Voice Selective Call is another method of unmuting a radio other than PL codes. Radios with Voice

1 Press / until CALL is

displayed.

2 Press l (the softkey below CALL).

3 The display shows the

last ID number transmitted or received.

4 Press ,.

5 The display shows the

last Group ID number transmitted or received.

PLANT POLICE

ZONE

MUTE CALL

ID: 1048

GROUP: 105

6 Press ,.

The display shows your radio’s ID number.

8 Press ,.

9 The display shows your

radio’s Group ID number.

10 Press to return

the radio to the home display.

MY ID:1048

MY GRP:001

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 55 Friday, April 13, 2007 2:47 PM

Page 58

STAT-ALERT

FEATURES

Selective Call may be programmed to unmute one of two ways:

1. (OR muting option) upon receiving proper PL

code or a Selective Call, or

2. (AND muting option) upon receiving both

proper PL code and Selective Call

Receiving a Voice Selective Call

Note: After answering a Voice Selective Call, the

caller’s ID number is stored in your radio as the “last ID number received”.

• Two automatic-reset features are available

for voice selective-call. These features reset the radio to voice selective call when the automatic reset timer expires.

1. Automatic Reset Without Carrier Override

The automatic-reset timer starts after the last voice message is completed, or after the radio is de-keyed (you released the PTT switch).

2. Automatic Reset With Carrier Override

When a carrier is detected, the automatic reset timer stops; when the carrier is lost, the automatic-reset timer starts over.

• Voice selective call automatic reset is

cancelled when the monitor button is pressed, or when the mode is changed. The automatic-reset timer is started over if it was running when either a voice selective call was again decoded or a successful transmission was completed.

Making a Voice Selective Call

There are four phases in making a Voice Selective call, namely

• initiating a Voice Selective call,

• entering the desired radio ID number,

• sending the radio ID number, and

• having the conversation.

1 When a call is received, the green LED blinks,

and a one-time, two-beep alert tone is emitted; on the display, the call-received status annunciator (F) blinks. A voice message will follow.

2 The display shows the

incoming caller’s ID number momentarily.

3 Return the radio back to voice selective call

operation by pressing the monitor button, or if so programmed, the radio can automatically reset to voice selective call.

4 The radio returns to the

home display.

ID: 2350

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 56 Friday, April 13, 2007 2:47 PM

Page 59

STAT-ALERT

FEATURES

Initiating a Voice Selective Call

Entering the Desired Radio ID Number

If the last ID number called is the desired number, go directly to Step 5.

To Enter a New Number

Note: Once you have started entering numbers,

the , key functions as a backspace key. Pressing it causes the last digit entered to be erased, and the cursor moves to the left.

When the last digit is erased, an additional press of this key causes the last ID number transmitted or received to be displayed; pressing / shows the first member of the list.

• If automatic Selective Call is enabled, your

radio remains in Selective Call until you

exit the mode. If automatic Selective Call is

disabled in your radio, the radio

immediately exits Selective Call when you

release the PTT.

• In both Selective Call and Call Alert, a * will

match any number in the ID position. For

example, paging ID 000* will page all IDs

from 0000-0009. Paging **** will page all

radios on the system.

To Enter a Number from the Call List

1 Press / until CALL is

displayed.

2 Press l (the softkey below CALL).

3 The display shows the

last ID number transmitted or received.

4a Enter the new four-digit ID number using the

keypad.

4b On the display, the old ID number disappears

and the new digits appear as they are being entered.

4c The cursor blinks indicating the location of the

next number to be entered.

ZONE

MUTE

CALL

ID: 2350

4a Press either , or /.

4b / takes you forward to the first or next

member of the list; , takes you backwards to the last or previous member of the list.

When at a member of the list, the display alternates between showing the member’s name and ID number.

Alternates between

and

CK TANG

ID: 2350

20L01-A_PR_UG_MTX4500.book Page 57 Friday, April 13, 2007 2:47 PM

Page 60

STAT-ALERT

FEATURES

To Enter a Number from a Location in the Call List

Note: The last member of the list is also the “last ID

transmitted or received” at position “00” on the list.

• If you enter a location number that does

not exist (for example, “15”), the display shows “INVALID ENTRY,” and the radio sounds an invalid-keypress tone and returns to Step 4b of this procedure.

Sending the Radio ID Number

STAT-ALERT CALL ALERT OPERATION

Stat-Alert Call Alert is a per-radio feature that provides a convenient way for the dispatcher to page you through your radio. This is especially useful in noisy environments, or when you need to be away from your radio equipment.

Receiving a Call Alert Page

4a Press either , or / to enter the call

list.

4b Enter the first digit of the location number. If

there are fewer than 10 members in the list, go directly to Step 4e.

4c If there are 10 or more members in the list,

the display shows “ID LOC#X_” (where X is the first digit). The cursor blinks to show the location of the second digit.

4d Enter the second digit of the location number.

4e The radio goes to that

position in the list. The display alternates between showing the member’s name and ID number.

Alternates between

and

CK TANG

ID: 2350

5 Press the PTT switch to transmit the ID

number. If enabled, an alert tone sounds during the transmission of the radio ID number. After the alert tone, you may talk.

1 Upon receiving a Call Alert page, four alert

tones sounds (repeats every 5 seconds).

2 The green LED lights and the Call Received

annunciator, F, blinks indicating a call is received.

3 The display shows the Caller ID, and then

alternates between the home display, and “PAGE RECEIVED”.

4 Press the PTT switch to answer the page. You

may have to make a voice selective call, if the radio that paged you is on selective call mode.

20L01-A_PR_UG_MTX4500.book Page 58 Friday, April 13, 2007 2:47 PM

Page 61

STAT-ALERT

FEATURES

Note: The blinking green LED, alert tone, and

blinking annunciator will continue until the Call Alert is acknowledged (press PTT, or press and release the monitor button).

Making a Call Alert

There are three phases in making a call alert, namely

• initiating a call alert,

• entering the radio ID number that you wish to page, and

• sending the call alert.

Initiating a Call Alert

Note: The same list is shared by both Call Alert and

Select Call features.

• If your radio has been so programmed, you

can press the page button for quick access to the Call Alert feature. This takes you directly to Step 3.

Entering the Radio ID Number that you wish to Page

The procedure for entering the Radio ID Number is exactly the same as the process outlined in the

Select Call section. Please refer to Entering the Desired Radio ID Number on

page 57.

5 The display shows the

current mode. The audible alert, LED and call received annunciator turns off.

6 The ID number of the radio that paged you is

stored as “the last ID number received.”

FIRE DEPT

1 Press / until PAGE is

displayed.

2 Press l (the softkey below PAGE).

3 The display shows the

last ID number transmitted or received.

PAGE

PHON

VIEW

ID: 2350

20L01-A_PR_UG_MTX4500.book Page 59 Friday, April 13, 2007 2:47 PM

Page 62

STAT-ALERT

FEATURES

Sending the Call Alert

If the Page is Unsuccessful

If the Page is Successful

PTT-ID

Stat-Alert PTT-ID is a per-mode feature describing an identification code transmission that is tied to the PTT switch. The ID code is automatically sent every time a voice transmission occurs (that is, the PTT switch is pressed). When PTT-ID comes before the voice transmission, you will hear a tone until the ID transmission is completed; this helps you avoid talking while the ID code is being transmitted. This tone can be disabled on a per-radio basis. Also, the ID code transmission can be programmed to follow the voice transmission.

RADIO CHECK

This feature allows the dispatcher to determine if a radio unit is on the air without disturbing the radio operator. This is a useful tool for the radio dispatcher to use for routine maintenance checks, or if there is reason to doubt the availability of a radio unit. When the dispatcher "checks" for the radio, the radio receives the command and automatically acknowledges it. The transmit (red) LED lights when the radio sends the acknowledgement.

EMERGENCY OPERATION

Please refer to Emergency Operation on page 46.

4 Press the PTT switch to transmit the ID

number.

5a If the called radio fails to acknowledge the

alert, a low-pitched alert tone sounds and the display changes to “NO ACKNOWLEDGE”.

5b Press the PTT switch to send the ID number

again, or press to hang up and return to the home display.

5a If you hear five beeps, the radio you are

paging is on the air and has received your page.

5b The radio automatically

returns to the home display

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 60 Friday, April 13, 2007 2:47 PM

Page 63

ACCESSORIES

Motorola offers a number of accessories to enhance the productivity of your two-way radio. Many of the available accessories are listed below. Your authorized Motorola dealer will also have a complete list of accessories.

ADAPTERS

ANTENNAS

BATTERIES

BELT

CARRY CASES

CHARGERS

COVERS

GMLN1108_ Adapter 12-Pin Hirose

NAD6502_R VHF Antenna NAE6483_R UHF Antenna PMAD4012_ VHF Antenna, Stubby, 136 – 155 MHz PMAD4013_ VHF Antenna, Stubby, 155 – 161 MHz PMAD4014_ VHF Antenna, Whip, 136 – 155 MHz PMAD4015_ VHF Antenna, Whip, 136 – 155 MHz

PMAD4023_

VHF Antenna, 14 cm, Whip,

150 – 161 MHz PMAD4025_ VHF Antenna, Stubby, 150 – 161 MHz PMAE4003_ UHF Antenna, 9 cm, 430 – 470 MHz

NNTN5510_R Li-Ion Battery 1480mAH (FM_C)

HLN9714_ Spring Belt Clip, 2.5 inch

GMLN1110_ Hard Leather Carry Case Keypad GMLN1112_ Soft Leather Carry Case Keypad

HTN3000_ 120V Single-Unit Rapid Charger HTN3003_ 120V Multi-Unit Rapid Charger

GMLN4226_ Dust Cover Kit

20L01-A_PR_UG_MTX4500.book Page 61 Friday, April 13, 2007 2:47 PM

Page 64

ACCESSORIES

HEADSETS

REMOTE SPEAKER MICROPHONES

GMLN1117_ Multi-PTT Lightweight Headset COMF

GMMN1111_

Noise-Canceling Remote Speaker Microphone

20L01-A_PR_UG_MTX4500.book Page 62 Friday, April 13, 2007 2:47 PM

Page 65

WARRANTY

LIMITED WARRANTY

MOTOROLA COMMUNICATION

PRODUCTS

I. WHAT THIS WARRANTY COVERS AND

FOR HOW LONG:

MOTOROLA INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

MTX1550 and MTX4550 Portable Units Two (2) Years

Product Accessories One (1) Year

Motorola, at its option, will at no charge either

repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this

warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.

MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.

20L01-A_PR_UG_MTX4500.book Page 63 Friday, April 13, 2007 2:47 PM

Page 66

WARRANTY

II. GENERAL PROVISIONS:

This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.

III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY.

This warranty gives specific legal rights, and there

may be other rights which may vary from state to state.

IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by Motorola through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call Motorola at 1-800-9272744 US/Canada.

20L01-A_PR_UG_MTX4500.book Page 64 Friday, April 13, 2007 2:47 PM

Page 67

WARRANTY

V. WHAT THIS WARRANTY DOES NOT

COVER:

A) Defects or damage resulting from use of the

Product in other than its normal and customary manner.

B) Defects or damage from misuse, accident,

water, or neglect.

C) Defects or damage from improper testing,

operation, maintenance, installation, alteration, modification, or adjustment.

D) Breakage or damage to antennas unless

caused directly by defects in material workmanship.

E) A Product subjected to unauthorized

Product modifications, disassemblies or repairs (including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim.

F) Product which has had the serial number

removed or made illegible.

G) Rechargeable batteries if:

1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering.

2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.

H) Freight costs to the repair depot. I) A Product which, due to illegal or

unauthorized alteration of the software/ firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.

J) Scratches or other cosmetic damage to

Product surfaces that does not affect the operation of the Product.

K) Normal and customary wear and tear.

VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

20L01-A_PR_UG_MTX4500.book Page 65 Friday, April 13, 2007 2:47 PM

Page 68

WARRANTY

A) that MOTOROLA will be notified promptly in

writing by such purchaser of any notice of such claim;

B) that MOTOROLA will have sole control of the

defense of such suit and all negotiations for its settlement or compromise; and

C) should the Product or parts become, or in

MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.

MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing

states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof.

Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.

VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of Illinois, USA.

20L01-A_PR_UG_MTX4500.book Page 66 Friday, April 13, 2007 2:47 PM

Page 69

Selecting a Trunked or Conventional Zone

1. / until ZONE is displayed.

2. l (the softkey below ZONE). The current zone name blinks on the display.

3. / until the desired zone name is displayed. —or— Enter the number of the desired zone.

4. Press . The displayed zone is the new selected zone.

Selecting a Mode (Trunked Talkgroup or Conventional Channel)

1. Turn the Mode Selector knob to the desired mode.

2. The display shows the selected mode’s name.

3. If the selected mode is unprogrammed, the display shows UNPROGRAMMED and

an invalid-mode tone is heard until a valid programmed mode is selected.

Sending a Trunked Call

1. Select the desired trunked zone and talkgroup (see above).

2. Press and hold the PTT button on the side of the radio and speak slowly and

clearly into the microphone area. The red LED lights when the radio is transmitting. When you have finished talking, release the PTT button to listen.

Sending a Conventional Call

1. Select the desired conventional zone and channel (see above).

2. Press and hold the PTT button on the side of the radio and speak slowly and

clearly into the microphone area. The red LED lights when the radio is transmitting. When you have finished talking, release the PTT button to listen.

Receiving a Trunked or Conventional Call

1. Use the Mode Selector knob to select the desired trunked talkgroup or

conventional channel. Make sure the PTT button is released.

2. Listen for voice activity. The LED indicator blinks green when your radio is

receiving.

3. When a call is received, press and hold the PTT button on the side of the radio

and speak slowly and clearly into the microphone area. The red LED lights when the radio is transmitting. When you have finished talking, release the

PTT button to listen.

MTX1550 and MTX4550 Quick Reference Card

Record the functions for your radio’s programmable buttons in the table provided below. For further information, see page 8 in this User Guide.

(Programmable)/

Side Button 1 (A)

(Programmable)

Side Button 2 (B)

(Programmable)

Top Button (D)

Mode Selector Knob

Keypad

Menu Keys

Microphone

(Programmable)

Side Button 3 (C)

Push-to-Talk

(PTT) Button

On/Off/Volume Knob

LED Indicator

Select Button

LCD Screen

Button Function Short Press Long Press Hold Down Page

20L01-A_PR_UG_MTX4500.book Page 67 Friday, April 13, 2007 2:47 PM

Page 70

20L01-A_PR_UG_MTX4500.book Page 67 Friday, April 13, 2007 2:47 PM

Page 71

TABLE DES

MATIÈRES

DROITS DE REPRODUCTION DE LOGICIEL

D'ORDINATEUR . . . . . . . . . . . . . . . . . . . . . .4

Sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Présentation de la radio . . . . . . . . . . . . . . .6

Pièces de la radio. . . . . . . . . . . . . . . . . . . . . .6

Modèles MTX1550 et MTX4550 . . . . . . . .6

Bouton Marche/Arrêt/Volume . . . . . . . . . .7

Bouton de sélection du mode . . . . . . . . . .7

Bouton de conversation (PTT) . . . . . . . . .7

Voyant DEL. . . . . . . . . . . . . . . . . . . . . . . .7

Microphone . . . . . . . . . . . . . . . . . . . . . . . .7

Boutons programmables. . . . . . . . . . . . . .7

Touches du clavier (pour les radios

de modèle ll seulement) . . . . . . . . . . . . . .9

Touches de menu (pour les radios

de modèle ll seulement) . . . . . . . . . . . . .10

Sélectionner une fonction . . . . . . . . . . . .10

Affichage du menu . . . . . . . . . . . . . . . . .11

Écrans et icônes LCD . . . . . . . . . . . . . . .11

Indications de tonalité d'alerte. . . . . . . . .12

Initiation . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Informations sur la pile . . . . . . . . . . . . . . . . 14

Soins et conseils pour la pile . . . . . . . . . 14

Recyclage ou élimination des piles . . . . 15

Recharge de la pile . . . . . . . . . . . . . . . . 15

Informations sur les accessoires . . . . . . . . . 16

Installation de la pile. . . . . . . . . . . . . . . . 16

Retrait de la pile . . . . . . . . . . . . . . . . . . . 16

Installation de l'antenne . . . . . . . . . . . . . 17

Retrait de l'antenne . . . . . . . . . . . . . . . . 17

Installation de la pince de ceinture. . . . . 18

Enlever la pince de ceinture . . . . . . . . . . 18

Fonctionnement de la radio . . . . . . . . . . . . . 19

Mise sous tension et hors tension

de la radio. . . . . . . . . . . . . . . . . . . . . . . . 19

Réglage du volume de la radio. . . . . . . . 19

Auto-contrôle radio . . . . . . . . . . . . . . . . . 19

Appels radio standard. . . . . . . . . . . . . . . . 20

Sélectionner une zone est un mode . . . . . . 20

Sélectionner une zone (pour les

radios de modèle ll seulement) . . . . . . . 20

Sélectionner un mode . . . . . . . . . . . . . . 20

Recevoir un appel . . . . . . . . . . . . . . . . . . . . 21

TABLE DES MATIÈRES

20L01-A_PR_UG_MTX4500.book Page 1 Tuesday, May 29, 2007 3:01 PM

Page 72

TABLE DES

MATIÈRES

Passer un appel . . . . . . . . . . . . . . . . . . . . . 21

Modes conventionnels. . . . . . . . . . . . . . 21

Modes partagés. . . . . . . . . . . . . . . . . . . 21

Avis de niveau de pile faible . . . . . . . . . 22

Fonctionnement du réglage

silencieux codé . . . . . . . . . . . . . . . . . . . 22

Niveau de puissance radiofréquence variable (certains modèles

sélectionnés uniquement) . . . . . . . . . . . 22

Fonctionnement en dégration progressive

(systéms partagés uniquement) . . . . . . . . . 22

Mettre les tonalités en mode atténué

(pour les radios à clavier uniquement) . . . . 23

Fonctions partagées. . . . . . . . . . . . . . . . . 24

Visualiser le numéro d'identification

de votre radio . . . . . . . . . . . . . . . . . . . . . . . 24

Fonctionnement optimisé pour les appels

privés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Répondre à un appel privé . . . . . . . . . . 25

Passer un appel privé . . . . . . . . . . . . . . 26

Laisser une page Avis d'appel. . . . . . . . 28

Fonctionnement Avis d'appel . . . . . . . . . . . 29

Répondre à une page Avis d'appel

avec un Appel de groupe. . . . . . . . . . . . 29

Passer un Avis d'appel . . . . . . . . . . . . . 29

Sélection automatique de sites multiples

(AMSS). . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Visualisation du site actuel . . . . . . . . . . .32

Forcer un changement de site . . . . . . . .33

Verrouiller et déverrouiller un site . . . . . .33

Fonctions conventionnelles . . . . . . . . . . .34

Rélais/Direct. . . . . . . . . . . . . . . . . . . . . . . . .34

Smart PTT . . . . . . . . . . . . . . . . . . . . . . . . . .35

Balayage . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Fonction de balayage. . . . . . . . . . . . . . . . . .36

Mettre le balayage sur Marche ou sur Arrêt à l'aide du clavier (pour les

radios avec clavier uniquement) . . . . . . .36

Suppression des modes de nuisance. . .37 Consulter une liste de balayage (pour

les radios avec clavier uniquement) . . . .38

Programmer une liste de balayage (pour

les radios avec clavier uniquement) . . . .38

Modes de balayage. . . . . . . . . . . . . . . . .40

Programmer la radio . . . . . . . . . . . . . . . . .41

Programmer les numéros d'une liste

de téléphone . . . . . . . . . . . . . . . . . . . . . .41

Programmer la liste d'appel . . . . . . . . . .42

20L01-A_PR_UG_MTX4500.book Page 2 Tuesday, May 29, 2007 3:01 PM

Page 73

TABLE DES

MATIÈRES

Fonction Téléphone . . . . . . . . . . . . . . . . . 45

Répondre à un appel téléphonique . . . . 45

Passer un appel téléphonique (pour

les radios de modèle ll seulement) . . . . 45

Fonctions spéciales . . . . . . . . . . . . . . . . . 50

Fonction d'urgence . . . . . . . . . . . . . . . . . . . 50

Envoyer une alarme d'urgence . . . . . . . 50

Envoyer une alarme d'urgence

silencieuse . . . . . . . . . . . . . . . . . . . . . . . 51

Annuler une alarme d'urgence. . . . . . . . 51

Envoyer un appel d'urgence . . . . . . . . . 51

Envoyer un appel d'urgence . . . . . . . . . 52

Urgence avec Voice to Follow

(voix à suivre). . . . . . . . . . . . . . . . . . . . . 52

Regroupage dynamique . . . . . . . . . . . . . . . 52

Sélection du mode . . . . . . . . . . . . . . . . . 53

Sélectionnez Activé et Désactivé. . . . . . 54

Fonction SmartZone . . . . . . . . . . . . . . . . . 55

Avantages de SmartZone . . . . . . . . . . . . . . 55

Échange de site dans SmartZone . . . . . 56

Visualisation du site actuel. . . . . . . . . . . 57

Forcer un changement de site . . . . . . . . 57

Verrouiller et déverrouiller un site . . . . . 57

Sélection du site préféré . . . . . . . . . . . . 58

Ignorer le signal « occupé ». . . . . . . . . . 58

Partage de site. . . . . . . . . . . . . . . . . . . . 59

Fonctions Stat-Alert . . . . . . . . . . . . . . . . . 60

Visualiser le numéro d'identification

de votre radio . . . . . . . . . . . . . . . . . . . . . . . 60

Fonction d'appel sélectif par voix

Stat-Alert. . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Réception d'un appel vocal sélectif . . . . 61

Passer un appel vocal sélectif. . . . . . . . 62

Fonction Avis d'appel Stat-Alert . . . . . . . . . 64

Réception d'une page Avis d’appel . . . . 64

Passer un Avis d'appel . . . . . . . . . . . . . 65

PTT-ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Verification de la radio . . . . . . . . . . . . . . . . 66

Fonction d'urgence . . . . . . . . . . . . . . . . . . . 66

Accessoires . . . . . . . . . . . . . . . . . . . . . . . 67

Adaptateurs . . . . . . . . . . . . . . . . . . . . . . . . 67

Antennes . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Piles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Ceinture . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Étuis de transport . . . . . . . . . . . . . . . . . . . . 67

Chargeurs. . . . . . . . . . . . . . . . . . . . . . . . . . 67

Housse de protection . . . . . . . . . . . . . . . . . 67

Casques . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Microphones de haut-parleur à distance . . 67

Garantie. . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Garantie limitée . . . . . . . . . . . . . . . . . . . . . 68

20L01-A_PR_UG_MTX4500.book Page 3 Tuesday, May 29, 2007 3:01 PM

Page 74

DROITS DE REPRODUCTION

DE LOGICIEL D'ORDINATEUR

DROITS DE REPRODUCTION DE LOGICIEL D'ORDINATEUR

Les produits Motorola décrits dans le présent guide peuvent inclure des logiciels Motorola protégés en vertu de la loi sur le droit d'auteur enregistrés dans des mémoires à semiconducteurs ou dans d'autres supports. Les lois du Canada, des États-Unis et d'autres pays protègent, au nom de Motorola, certains droits exclusifs visant les logiciels, y compris mais non de façon limitative, les droits exclusifs de copie et de reproduction sous toute forme des logiciels protégés par la loi sur le droit d'auteur.

Par conséquent, la loi sur le droit d'auteur protégeant tous les logiciels inclus avec les produits décrits dans le présent guide interdit toute copie, reproduction, modification, ingénierie à rebours ou distribution de ces logiciels sans l'autorisation écrite expresse de Motorola. Par surcroît, aucune licence n'est accordée directement, par inférence, estoppel ou autre en vertu des droits d'auteur, des droits de brevets ou d'une demande de brevet pour tout achat d'un produit Motorola, à l'exception d'une licence d'utilisation normale et non exclusive délivrée par l'exécution d'une loi lors de la vente d'un produit.

20L01-A_PR_UG_MTX4500.book Page 4 Tuesday, May 29, 2007 3:01 PM

Page 75

SÉCURITÉ

Ce guide de l'utilisateur couvre le fonctionnement des Radios Portables MTX1550 et MTX4550.

Cette radio ne doit être utilisée qu'à des fins professionnelles afin de respecter les normes d'exposition à l'énergie électromagnétique ICNIRP RF. Avant d'utiliser ce produit, lisez les informations relatives à l'exposition à l'énergie électromagnétique et les instructions concernant le fonctionnement dans le livret Sécurité du produit et consignes relatives à l'exposition à l'énergie électromagnétique (Numéro de publication Motorola 6881095C98_), pour assurer le respect des limites d'exposition à l'énergie électromagnétique.

Avant d'utiliser ce produit, lisez les instructions de fonctionnement pour l'utilisation en toute sécurité figurant dans la brochure Sécurité produit et exposition à la fréquence radioélectrique 6881095C98_ fournie avec votre radio.

Attention

20L01-A_PR_UG_MTX4500.book Page 5 Tuesday, May 29, 2007 3:01 PM

Page 76

PRÉSENTATION DE

LA RADIO

PRÉSENTATION DE LA RADIO

PIÈCES DE LA RADIO

Modèles MTX1550 et MTX4550

(Programmable)/

Bouton latéral 1 (A)

(Programmable)

Bouton latéral 3 (C)

(Programmable)

Bouton Supérieur (D)

Clavier

Touches de menu

Bouton de sélection

(PTT)

Bouton de

Bouton Marche/

Voyant DEL

(Programmable)

Bouton latéral 2 (B)

Écran à affichage

Microphone

Bouton de Sélection

du mode

Arrêt/Volume

conversation

à cristaux liquides

Panneau

du connecteur

latéral

Panneau

du connecteur

latéral

20L01-A_PR_UG_MTX4500.book Page 6 Tuesday, May 29, 2007 3:01 PM

Page 77

PRÉSENTATION DE

LA RADIO

Bouton Marche/Arrêt/Volume

Permet de mettre la radio sous tension ou hors tension et d'en régler le volume.

Bouton de sélection du mode

Sélectionne le mode fonctionnement requis.

Bouton de conversation (PTT)

Appuyez sur le bouton de conversation et maintenez-le enfoncé pour parler; relâchez-le pour écouter.

Voyant DEL

Indique l'état des conditions de fonctionnement de la radio (voir tableau ci-dessous) :

Microphone

Lorsque vous envoyez un message, tenez le microphone à environ 2,5 à 5 cm (1 à 2 po) de votre bouche et parlez clairement dans le microphone.

Boutons programmables

Plusieurs boutons de votre radio peuvent être programmés (en utilisant le logiciel de programmation du client — CPS) pour activer les fonctions de la radio.

Les boutons programmables sont :

• Le bouton supérieur

• Les trois boutons sur le côté

Vérifiez avec votre concessionnaire ou votre représentant de Motorola que vous disposez de la liste complète des fonctions prises en charge par les boutons programmables de votre radio.

Bouton PTT enclenché (Émission Radio)

Rouge permanent

La radio est en cours d'émission (le bouton de conversation est enclenché).

DEL non allumé Aucune émission radio

Rouge clignotant

Niveau de pile faible (mode conventionnel seulement ; programmable par un Concessionnaire Motorola autorisé).

Temporairement vert

La radio a bien été mise sous tension

Bouton PTT relâché

(Radio en mode de Réception)

Rouge clignotant

Mode d'occupation (mode conventionnel seulement)

Vert clignotant

Réception d'un appel téléphonique, appel Conversation privée ou page Avis d'appel

20L01-A_PR_UG_MTX4500.book Page 7 Tuesday, May 29, 2007 3:01 PM

Page 78

PRÉSENTATION DE

LA RADIO

Le tableau ci-dessous indique les fonctions disponibles si vous faites :

• Appui de courte durée - appuyez rapidement

et relâchez les boutons programmables ou

• Appui de longue durée - appuyez sur les

boutons programmables pendant un certain

temps avant de les relâcher ou

• Bouton enclenché - appuyez sur les boutons

programmables et maintenez-les enfoncés lors de la vérification de l'état ou en effectuant des réglages.

Bouton Appui de courte durée

Appui de longue

durée

Enclenché

Contrôleur/ Contrôleur permanent

—

Contrôle continuellement le canal sélectionné.

Contrôle le canal sélectionné pour toute activité.

Réglage du volume

——

Émet une tonalité demandant d'ajuster le volume de votre radio.

Balayage

Alterne entre les opérations démarrer/arrêter le balayage.

——

Supprimer la nuisance

Supprime temporairement un membre actif non prioritaire et non désirable qui effectue un balayage.

——

Recherche Effectue une recherche système.

Éclairage

Permet d'allumer/éteindre la lampe de rétro-éclairage de votre radio.

——

Urgence Entre en mode Urgence. Quitte le mode Urgence. — Appel Entre ou quitte un appel privé. Page Entre ou quitte un Avis d'appel.

Réponse d'appel

Permet de répondre à ou de quitter un Appel privé ou un Avis d'appel.

——

Téléphone Entre ou quitte le mode Téléphone. — —

20L01-A_PR_UG_MTX4500.book Page 8 Tuesday, May 29, 2007 3:01 PM

Page 79

PRÉSENTATION DE

LA RADIO

Touches du clavier (pour les radios de modèle ll seulement)

Ces touches sont utilisées pour composer un numéro de téléphone, effectuer un appel radio ou entrer des informations pour programmer les listes de la radio.

Le tableau suivant indique le cycle de caractère pour chaque touche lorsque vous entrez des informations pour programmer les listes de la radio.

Remarque : La séquence du tableau ci-dessus est

valide lorsque vous entrez des informations sur un affichage blanc. Toutefois, lorsque vous modifiez des informations existantes, cette séquence peut être différente. Par exemple, si le dernier caractère entré est « R », le fait d'appuyer sur 7 pour entrer le caractère suivant fera démarrer le cycle de caractère à « S » et NON PAS à « P ».

• Lorsque vous modifiez des informations

existantes, le fait d'appuyer sur 1 démarre TOUJOURS le cycle de caractère à « espace blanc » et NON à « 1 ».

To u c h es

Nombre de fois où la touche est enfoncée

123456

1 1

Espace

blanc

2 ABC2

3 DEF3

123 456 789 *0#

4 GH I4

5 JKL5

6 MNO6

7 PQRS7

TUV8

9 WX YZ9

# #-+. /\

20L01-A_PR_UG_MTX4500.book Page 9 Tuesday, May 29, 2007 3:01 PM

Page 80

PRÉSENTATION DE

LA RADIO

Touches de menu (pour les radios de modèle ll seulement)

Sélectionner une fonction

Votre radio possède une fonction tout à fait unique qui est l'utilisation de l'affichage pour vous donner un accès rapide à de nombreuses fonctions de la radio sans avoir de touche dédiée pour chaque fonction.

Le nom des fonctions (APPEL, SOURDINE etc.) est indiqué sur l'affichage, avec un jeu de trois fonctions à la fois. La sélection des fonctions est contrôlée directement par les trois touches sous le nom des fonctions : la touche de gauche commande la fonction de gauche, la touche centrale contrôle la fonction au centre et la touche de droite contrôle la fonction de droite.

Touches programmables (l;l)

Lorsque vous êtes déjà en mode Menu, ces touches sont utilisées pour faire des sélections de menu.

Touches fléchées Gauche et Droite (,/)

Les touches fléchées Gauche et Droite sont utilisées pour faire défiler l'affichage parmi les fonctions et les listes de la radio. La liste ne comporte pas de point final, ainsi, si vous continuez de faire défiler dans une direction, l'affichage reviendra automatiquement au début de la liste. Si vous maintenez l'une des touches enfoncées, l'affichage défile à plus grande vitesse jusqu'à ce que vous relâchiez la touche.

La touche fléchée Gauche est également utilisée pour faire des modifications lorsque vous entrez manuellement des informations à partir du clavier.

Le fait d'appuyer sur la touche fléchée Gauche lorsque vous éditez des informations numériques (comme des numéros de téléphone) reculera à la position précédente et effacera l'affichage, un caractère à la fois. Si vous avez effacé tous les chiffres, le fait d'appuyer à nouveau sur la touche fléchée Gauche renverra l'affichage à la liste préprogrammée.

Le fait d'appuyer sur la touche Gauche, lorsque vous éditez des informations comportant des lettres (comme des noms de membres), déplace le curseur d'une position vers la gauche.

Touche HOME (Accueil) ( )

La touche HOME revient toujours à l'affichage initial (par défaut). Dans la plupart des cas, c'est le mode actuellement utilisé. De plus, si vous utilisez une fonction qui le nécessite, le fait d'appuyer sur la touche HOME sauvegarde les informations en mémoire avant de passer à l'affichage initial.

l;l ,/

Touche

programmable 1

Touche

programmable 3

Gauche Position

initiale

(Home)

Droite

Touche

programmable 2

20L01-A_PR_UG_MTX4500.book Page 10 Tuesday, May 29, 2007 3:01 PM

Page 81

PRÉSENTATION DE

LA RADIO

Certaines fonctions de la radio passent automatiquement à l'affichage initial, une fois l'opération terminée, sans avoir à appuyer sur la touche HOME, limitant ainsi le nombre de touches sur lesquelles vous devez appuyer.

Affichage du menu

Les éléments de menu peuvent être affichés en vidéo normale ou en vidéo inversée (au moyen du CPS). Tous les éléments de menus dans les exemples donnés dans ce manuel sont présentés en vidéo inversée.

L'ordre d'affichage des éléments du menu est programmable Ainsi, l'ordre des éléments du menu sur votre radio peut être différent de celui indiqué ici dans ce manuel. De ce fait, appuyez sur touche programmable adéquate pour faire vos sélections de menu. Toutes les descriptions données pour les fonctions et les affichages indiqués après la sélection sont valides.

Écrans et icônes LCD

L'écran affiche le mode sélectionné, le canal, le menu et les informations de la radio. Les deux rangées supérieures de l'écran présentent les symboles des

indicateurs d'état de la radio qui sont expliqués dans le tableau suivant.

Symbole Nom et description

Indicateur XPAND

Indique que la fonction compressionexpansion de votre radio est activée.

Indicateur du niveau de puissance

R s'allume lorsque votre radio est configurée pour émettre en mode d'alimentation faible. S s'allume lorsque votre radio est configurée pour émettre en mode d'alimentation élevée.

Indicateur de réglage silencieux du porteur

Indique lorsque le mode conventionnel actif est contrôlé en mode de réglage silencieux du porteur ; MARCHE = CONTRÔLÉ /

ARRÊT = NON CONTRÔLÉ.

Appel reçu

Clignote lorsqu'un appel ou une page est reçu.

Indicateur de balayage

Indique lorsque la radio effectue un balayage ; ON (Marche) = BALAYAGE / OFF (Arrêt) = NON BALAYAGE.

Balayage prioritaire

Un point à côté de l'avertisseur de balayage indique la réception d'un mode de priorité ; POINT CLIGNOTANT = PRIORITÉ 1 POINT PERMANENT = PRIORITÉ 2.

20L01-A_PR_UG_MTX4500.book Page 11 Tuesday, May 29, 2007 3:01 PM

Page 82

PRÉSENTATION DE

LA RADIO

Indications de tonalité d'alerte

Votre radio génère un nombre de tonalités audibles pour indiquer les conditions de fonctionnement de la radio :

• Niveau de pile faible – Une condition Niveau de pile faible est indiquée par un son aigu, à la manière d'un grillon, lorsque le bouton de conversation PTT est relâché après une transmission.

• Mise sous tension réussie – Une tonalité courte, moyennement aiguë, lorsque la radio est

initialement allumée, indique que la radio a réussi le test d'auto-contrôle et qu'elle peut être utilisée.

• Mise sous tension non réussie – Une tonalité courte, faiblement aiguë, lorsque la radio est initialement allumée, indique que la radio n'a pas réussi le test d'auto-contrôle et qu'elle n'est pas prête à être utilisée. Contactez votre interlocuteur technique pour obtenir de l'aide.

• Transmission sur mode réception uniquement – Si vous appuyez sur le bouton de conversation PTT tout en étant en mode « réception uniquement », vous entendrez une tonalité d'alerte continue, faiblement aiguë, indiquant qu'aucune transmission n'est possible dans ce mode. Cette tonalité continue jusqu'à ce que le bouton de conversation PTT soit relâché.

• Émission invalide en mode d'occupation – Si vous appuyez sur le bouton PTT tout en étant en mode Occupé, vous entendrez une tonalité d'alerte continue, faiblement aiguë, indiquant qu'aucune émission n'est possible dans ce mode. Cette tonalité continue jusqu'à ce que le bouton de conversation PTT soit relâché.

• Émission invalide avec pile déchargée – Si vous appuyez sur le bouton PTT avec une pile déchargée, vous entendrez une tonalité d'alerte continue, faiblement aiguë, indiquant que l'émission est impossible.

• Mode invalide – Une tonalité continue, faiblement aiguë, est émise lorsque vous tentez une opération invalide ou non programmée avec la radio.

• Appui de touche valide (correct) – Une brève tonalité moyennement aiguë lorsqu'une touche

Direct

Indique si vous parlez directement à une autre radio (mode Intercommunication) ou par le biais d'un relais. ON (Marche) = DIRECT OFF (Arrêt) = RELAIS.

Mode programmation / visualisation

Indique lorsque la radio est en mode de programmation ou de visualisation ; ON (Marche) = MODE VISUALISATION CLIGNOTE = MODE PROGRAMMATION.

Indicateur de qualité du signal

Indique la qualité du signal radio. Si voius voyez cinq barres, cela indique le meilleur signal possible (Smart Zone uniquement).

Indicateur du niveau de pile

Indique la charge restante dans votre pile, d'après le nombre de barres affichées.

Clignote, indique pile déchargée.

Symbole Nom et description

20L01-A_PR_UG_MTX4500.book Page 12 Tuesday, May 29, 2007 3:01 PM

Page 83

PRÉSENTATION DE

LA RADIO

du clavier est enfoncée indique que la fonction de cette touche a été acceptée.

• Appui de touche invalide (incorrect) – Une brève tonalité moyennement aiguë lorsqu'une touche du clavier est enfoncée indique que la fonction de cette touche a été rejetée.

• Entrée d'alarme d'urgence – Une tonalité brève moyennement aiguë émise lorsque le bouton d'urgence est enfoncé indique que la radio est passée en mode d'urgence.

• Alarme d'urgence/Quitter l'appel – Une tonalité continue moyennement aiguë émise lorsque la radio est en mode d'urgence indique que la radio n'est plus dans ce mode.

• Mode dégradé (pour les systèmes partagés uniquement) – Une faible tonalité « bip » émise toutes les 10 secondes indique que la radio fonctionne en mode dégradé.

• Avertissement de temporisation – Le temporisateur de votre radio limite la durée de votre transmission. Lorsque vous appuyez sur le bouton de conversation PTT (transmission), une tonalité d'avertissement brève moyennement aigüe est émise quatre secondes avant la fin de la durée autorisée.

• Indicateur de temporisation expiré – Si vous maintenez le bouton de conversation PTT enfoncé plus longtemps que la durée autorisée par le temporisateur, une tonalité continue légèrement aiguë est émise pour indiquer que votre transmission a été coupée. Cette tonalité continue jusqu'à ce que le bouton de conversation PTT soit relâché.

• Téléphone occupé – Une tonalité « bah-bah-bahbah » lors de l'accès à la liaison téléphonique indique que tous les modes disponibles sont occupés et que la radio est en file pour la prochaine ligne de téléphone disponible.

• Call Alert

(Page) reçu – Quatre tonalités groupées moyennement aiguës émises toutes les cinq secondes indiquent que votre radio a reçu une page Avis d'appel.

• Call Alert

(Page) envoyé – Une simple tonalité moyennement aiguë (confirmation centrale), suivie d'un groupe de quatre tonalités moyennement aiguës, indique qu'une page Avis d'appel envoyée par votre radio a bien été reçue par la radio cible.

• Private Conversation

(Appel reçu pour une conversation privée) – Deux tonalités groupées moyennement aiguës indiquent que votre radio a reçu un appel pour conversation privée. Cette séquence est répétée toutes les cinq secondes pendant environ 20 secondes pour une conversation privée évoluée.

• Système partagé occupé (pour les systèmes partagés uniquement) – Une tonalité « bah-bahbah-bah » lors de l'accès au système partagé indique que tous les canaux disponibles sont occupés et que la radio est en file pour le prochain canal disponible.

• Rappel (systèmes partagés uniquement) – Un groupe de trois tonalités moyennement aiguës (di-di-dit) indique qu'un groupe de conversation est à présent disponible pour la transmission que vous avez requise précédemment.

20L01-A_PR_UG_MTX4500.book Page 13 Tuesday, May 29, 2007 3:01 PM

Page 84

INITIATION

INFORMATIONS SUR LA PILE

Soins et conseils pour la pile

Ce produit fonctionne avec une pile au lithium-ion rechargeable.

Les conseils suivants pour la pile vous permettront d'obtenir la meilleure performance et le cycle de vie le plus long possible avec votre pile Motorola rechargeable.

• Chargez votre nouvelle pile la nuit (14 – 16 heures) avant de l'utiliser pour obtenir une capacité et une performance de pile maximum.

• Le fait de charger une pile à l’aide d’un accessoire non approuvé par Motorola peut endommager la pile et annuler sa garantie.

• Lorsque vous chargez une pile reliée à la radio, éteignez l’appareil afin d’assurer une charge complète.

• Dans l'idéal, la pile doit être conservée à la température ambiante (environ 25°C ou 77°F). Charger une pile froide (température inférieure à 10°C ou 50°F) peut entraîner une fuite d’électrolyte et, en fin de compte, la défaillance de la pile.

• Inversement, charger une pile chaude (température supérieure à 35°C ou 95°F) réduit la capacité de décharge, atténuant ainsi le rendement de la radio. Les chargeurs de pile à taux rapide de Motorola sont dotés d’un circuit de détection de température pour assurer que la pile est chargée conformément aux températures spécifiées.

• Les nouvelles piles peuvent être stockées jusqu'à deux ans sans perte de cycle significative. Sockez les nouvelles piles et les piles non utilisées dans une zone fraîche et sèche.

• Les piles qui ont été entreposées doivent être chargées la nuit.

• Ne remettez pas des piles complètement chargées sur le chargeur pour avoir de l'énergie supplémentaire. Cette action diminue considérablement le cycle de vie.

• Ne laissez pas votre radio et la pile dans le chargeur lorsque vous n'effectuez pas de chargement. Le fait de charger une pile en continu diminue sa durée de vie. (N'utilisez pas votre chargeur comme socle pour la radio.)

• Pour une durée de vie de la pile et un fonctionnement optimal, n'utilisez que des chargeurs de la marque Motorola. Ils sont conçus pour fonctionner comme système à énergie totale.

20L01-A_PR_UG_MTX4500.book Page 14 Tuesday, May 29, 2007 3:01 PM

Page 85

INITIATION

Recyclage ou élimination des piles

Motorola approuve et encourage le recyclage de toutes les piles rechargeables. Contactez votre concessionnaire Motorola local pour obtenir plus d'informations.

Recharge de la pile

Si une pile est neuve ou si son niveau de charge est très faible (l'indicateur du niveau de pile montre soit un segment, soit aucun segment), vous devez charger la pile avant de pouvoir l'utiliser dans votre radio.

Remarque :

• Lorsqu'elles arrivent directement de l'usine, les piles ne sont pas chargées. Les nouvelles piles peuvent indiquer prématurément une charge complète. Chargez toute pile neuve pendant 14 – 16 heures avant l'utilisation initiale.

• Le chargement d'une pile doit être effectué

UNIQUEMENT dans une zone non dangereuse.

1. Placez la radio avec la pile connectée ou la pile

seule, dans le chargeur.

2. Le voyant DEL du chargeur indique la

progression de la charge :

Les chargeurs de pile chargent uniquement les piles autorisées par Motorola qui sont répertoriées ci-dessous. D'autres piles sont susceptibles de ne pas se charger.

NiCd

Chargeur DEL État

Rouge Pile en cours de charge

Vert La pile est complètement

rechargée.

Rouge clignotant* La pile ne peut être rechargée.

Clignotement jaune Le chargeur est prêt pour charger

Clignotement vert La pile est rechargée à 90%.

La pile est endommagée. Contactez votre concessionnaire.

Numéros

des

pièces

Description

NNTN5510 Pile Li-Ion 1480mAH (FM_C)

20L01-A_PR_UG_MTX4500.book Page 15 Tuesday, May 29, 2007 3:01 PM

Page 86

INITIATION

INFORMATIONS SUR LES ACCESSOIRES

Installation de la pile

Retrait de la pile

1 Insérez les extrémités de la pile dans

les fentes inférieures de la radio.

2 Appuyez sur la partie supérieure de la pile

vers la radio, jusqu'à ce que vous entendiez un clic.

1 Éteignez la radio (voir page 19).

2 Glissez les deux loquets de la pile vers le bas.

3 Tirez la partie supérieure de la pile dans la

direction opposée à l'appareil.

Loquets

de la pile

20L01-A_PR_UG_MTX4500.book Page 16 Tuesday, May 29, 2007 3:01 PM

Page 87

INITIATION

Installation de l'antenne Retrait de l'antenne

1 Alignez l'extrémité filetée de l'antenne avec

le connecteur d'antenne de la radio.

2 Vissez l'antenne dans le sens horaire pour

la fixer à la radio.

1 Dévissez l'antenne dans le sens antihoraire

pour la retirer.

20L01-A_PR_UG_MTX4500.book Page 17 Tuesday, May 29, 2007 3:01 PM

Page 88

INITIATION

Installation de la pince de ceinture Enlever la pince de ceinture

1 Alignez les encoches de la pince de ceinture

avec celles de la pile.

2 Appuyez vers le bas sur la pince de ceinture

jusqu'à ce que vous entendiez un clic.

1 Utilisez une clé pour détacher l'onglet de la

pince de ceinture.

2 Faites glisser la pince de ceinture vers le

haut pour l'enlever.

Onglet d'agrafe

de ceinture

20L01-A_PR_UG_MTX4500.book Page 18 Tuesday, May 29, 2007 3:01 PM

Page 89

INITIATION

FONCTIONNEMENT DE LA RADIO

Mise sous tension et hors tension de la radio

Réglage du volume de la radio

Auto-contrôle radio

Mettez la radio sous tension en faisant tourner le bouton de commande du volume dans le sens horaire. La radio effectue un auto-contrôle de mise sous tension et, si ce test est réussi, l'affichage indique momentanément AUTO CONTRÔLE. Une tonalité aiguë de mise sous tension est émise pour indiquer que la radio a réussi le test d'auto-contrôle.

Si la radio ne passe pas le test d'auto-contrôle, l'affichage indique ERREUR XX/XX (où XX/XX est un code d'erreur alphanumérique) et vous entendrez une tonalité légèrement aiguë, indiquant une erreur de mise sous tension. Éteignez la radio, vérifiez la pile et remettez la radio sous tension. Si la radio ne passe toujours pas le test d'auto-contrôle, celle-ci a un problème. Contactez votre atelier de service Motorola le plus proche.

Remarque : Le test d'auto-contrôle vérifie que les

systèmes basés sur microprocesseur de la radio fonctionnent mais il ne passe pas en revue tous les composants de fréquence radio et il ne vérifie pas le fonctionnement de toutes les fonctions spécifiques au client. Motorola recommande de faire vérifier régulièrement la fonctionnalité de la radio par un atelier de service Motorola autorisé.

Pour mettre la radio sous tension, tournez le bouton Marche/Arrêt/Volume dans le sens horaire.

Pour mettre la radio hors tension, tournez le bouton Marche/Arrêt/Volume dans le sens anti-horaire jusqu'à ce que vous entendiez un clic.

Faites tourner le bouton Marche/Arrêt/Volume pour régler le niveau du volume.

Écoutez jusqu'à ce que vous entendiez une transmission, puis ajustez le volume pour obtenir un niveau d'écoute confortable.

ON (Marche) OFF (Arrêt)

Ou, si un bouton est programmé pour le « Réglage du volume », appuyez sur celui-ci et ajustez le volume pour obtenir un niveau d'écoute confortable.

20L01-A_PR_UG_MTX4500.book Page 19 Tuesday, May 29, 2007 3:01 PM

Page 90

APPELS RADIO

STANDARD

APPELS RADIO STANDARD

Cette section présente les fonctions de base de votre radio. Toutes les références faites aux indications de l'affichage ne sont valides que pour les radios de modèle II. Dans cette section, l'affichage ci-dessous

est utilisé pour indiquer l'affichage initial de la radio.

SÉLECTIONNER UNE ZONE EST UN MODE

Un mode est un canal ou un groupe de conversation et toutes les fonctions liées qui sont programmées. Une zone est un groupe de modes qui est sélectionné à l'aide des touches de menu. Avant d'utiliser votre radio pour recevoir ou envoyer des messages, sélectionnez tout d'abord la zone et le mode souhaités.

Sélectionner une zone (pour les radios de modèle ll seulement)

Sélectionner un mode

1 Appuyez sur /

jusqu'à ce que ZONE s'affiche.

2 Appuyez sur l

(touche programmable sous ZONE). Le nom de la zone actuelle clignote sur l'affichage.

Par exemple

PLANT POLICE

ZONE

MUTE

CALL

PLANT POLICE

3 Appuyez sur /

jusqu'à ce que le nom de la zone souhaitée s'affiche.

—ou—

Entrez le numéro de la zone souhaitée.

Par exemple

4 Appuyez sur . 5 La zone affichée est

la nouvelle zone sélectionnée.

1 Faites tourner le bouton de sélection du

mode vers le mode souhaité.

2 L'affichage indique

le nom du mode sélectionné.

Par exemple

3 Si le mode

sélectionné n'est pas programmé, une tonalité de mode invalide est émise jusqu'à ce qu'un mode programmé valide soit sélectionné.

CITY POLICE

PLANT MODE 1

UNPROGRAMMED

20L01-A_PR_UG_MTX4500.book Page 20 Tuesday, May 29, 2007 3:01 PM

Page 91

APPELS RADIO

STANDARD

RECEVOIR UN APPEL

PASSER UN APPEL Modes conventionnels

Remarque : N'interrompez pas un autre utilisateur.

Si le mode actuel est programmé pour recevoir PL, vérifiez que le mode n'est pas utilisé en appuyant sur le bouton du moniteur pour écouter toute activité possible.

• Si la fonction mode d'occupation est

activée, un voyant rouge clignotant au moment de la réception (bouton de conversation PTT relâché) indique que le mode est actuellement occupé.

• Si un mode est programmé pour la

réception uniquement et si vous tentez d'émettre sur ce mode, une tonalité mode invalide sera émise jusqu'à ce que le bouton de conversation PTT soit relâché.

Modes partagés

Remarque : Si vous entendez un signal occupé

(un son à basse fréquence « bah-bah-bahbah »), relâchez le bouton de conversation PTT et attendez qu'une tonalité de rappel « di-di-dit ») soit émise. Lorsque vous entendez la tonalité de rappel, vous avez

1 Mettez la radio sous tension et sélectionnez

la zone et le mode souhaités (consultez Sélectionner une zone et un mode à la page 20).

2 Votre radio est à présent réglée pour

recevoir des appels sur le mode sélectionné.

1 Mettez la radio sous tension et sélectionnez

la zone et le mode conventionnels souhaités (consultez Sélectionner une zone et un mode à la page 20).

2 Appuyez sur le bouton de conversation PTT

sur le côté de la radio et maintenez-le enfoncé. Parlez doucement et distinctement avec la bouche près du microphone. Le voyant rouge s'allume de manière continue lorsque la radio est en cours d'émission.

3 Lorsque vous avez fini de parler, relâchez le

bouton de conversation PTT pour écouter.

1 Mettez la radio sous tension et sélectionnez

la zone et le mode partagés souhaités (consultez Sélectionner une zone et un mode à la page 20).

2 Appuyez sur le bouton de conversation PTT

sur le côté de la radio et maintenez-le enfoncé. Parlez doucement et distinctement avec la bouche près du microphone. Le voyant DEL rouge s'allume lorsque la radio est en cours d'émission. Lorsque vous avez fini de parler, relâchez le bouton de conversation PTT pour écouter.

20L01-A_PR_UG_MTX4500.book Page 21 Tuesday, May 29, 2007 3:01 PM

Page 92

APPELS RADIO

STANDARD

trois secondes pour appuyer sur le bouton de conversation PTT. Vous pouvez ainsi passer un autre appel sans obtenir de signal occupé.

• Si la tonalité continue d'un signal

d'interdiction est émise lorsque vous appuyez sur le bouton de conversation PTT, la transmission n'est pas possible. La radio peut être hors de portée.

Avis de niveau de pile faible

Votre radio émet une tonalité d'avis lorsqu'une condition de niveau de batterie faible est détectée.

Fonctionnement du réglage silencieux codé

Tone Private-Line® (PL), Digital Private-Line

(DPL) et le fonctionnement de réglage silencieux du porteur sont disponibles sur votre radio, sur la base d'un mode à la fois. Lorsque vous êtes en fonctionnement de réglage silencieux du porteur, vous pouvez entendre tout le trafic sur le mode. Lorsque vous êtes en fonctionnement PL ou DPL, votre radio répond uniquement aux messages qui vous sont destinés. Lorsque cette fonction est en mode asservi, PL, DPL ou le réglage silencieux du porteur est programmé pour chaque mode.

Lorsque la radio fonctionne en réglage silencieux du porteur, l'affichage indique

Niveau de puissance radiofréquence variable (certains modèles sélectionnés uniquement)

Les radios peuvent avoir plus d'un niveau de puissance. Le niveau de puissance élevée peut être programmé sur les modes ou la puissance élevée est autorisée et le niveau de puissance faible peut être programmé sur tous les autres modes. La fonction Niveau de puissance élevée/faible peutêtre sélectionnée à l'aide des touches du menu.

FONCTIONNEMENT EN DÉGRATION PROGRESSIVE (SYSTÉMS PARTAGÉS UNIQUEMENT)

Le système « Dégradation progressive » assure la possibilité de communication radio en continu en cas de panne d'un système partagé. Votre radio passe automatiquement en fonctionnement Dégradation progressive si le contrôleur central de partage tombe en panne pour une raison ou une autre. Lorsque vous vous trouvez en fonctionnement Dégradation progressive sur la fréquence prédéterminée d'un mode conventionnel. Lorsque le système partagé repasse en fonctionnement normal, la radio quitte automatiquement le fonctionnement en dégradation progressive et revient au fonctionnement partagé.

20L01-A_PR_UG_MTX4500.book Page 22 Tuesday, May 29, 2007 3:01 PM

Page 93

APPELS RADIO

STANDARD

Pendant le fonctionnement en dégradation progressive,

METTRE LES TONALITÉS EN MODE ATTÉNUÉ (POUR LES RADIOS À CLAVIER UNIQUEMENT)

Les tonalités du clavier de la radio que vous entendez à chaque pression de touche peuvent être éteintes (mode discrétion) ou non (mode non discrétion) selon votre choix. Pour utiliser la fonction Discrétion du clavier

Remarque : Le fait d'appuyer sur ou sur le

bouton PTT permet de quitter ce menu sans changer la sélection d'atténuation.

1 Vous entendrez une

faible tonalité toutes les 10 secondes.

Alternance entre

2 Votre radio n'est plus en réglage silencieux.

1 Appuyez sur /

jusqu'à ce que MUTE (Discrétion) s'affiche.

FAILSOFT

PLANT POLICE

ZONE

MUTE

CALL

2 Appuyez sur l

(touche programmable sous MUTE).

Vous verrez momentanément l'état actuel d'atténuation.

Puis

3 Appuyez sur

la touche programmable en dessous de l'état de discrétion souhaité (activé ou désactivé) La radio revient à l'affichage initial.

TONES ON

TONES OFF

OFF

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 23 Tuesday, May 29, 2007 3:01 PM

Page 94

FONCTIONS

PARTAGÉES

FONCTIONS PARTAGÉES

Cette section présente les fonctions partagées de votre radio. Toutes les références faites aux indications de l'affichage ne sont valides que pour les radios de modèle II. Dans cette section, l'affichage ci-dessous

est utilisé pour indiquer l'affichage initial de la radio.

VISUALISER LE NUMÉRO D'IDENTIFICATION DE VOTRE RADIO

Pour visualiser le numéro d'identification de votre radio

Remarque : Si votre radio a été programmée de

cette manière, vous pouvez appuyer sur le bouton d'appel pour obtenir un accès rapide et visualiser le numéro d'identification de votre radio. Ceci vous amène directement à l'étape 3.

FONCTIONNEMENT OPTIMISÉ POUR LES APPELS PRIVÉS

La fonction Fonctionnement optimisé pour les appels privés vous permet non seulement d'avoir une conversation entendue uniquement par les deux parties impliquées, mais elle vous permet également de déterminer si la radio à partir de laquelle vous passez l'appel est en service. La radio appelée peut également visualiser le numéro d'identification de la radio qui passe l'appel et ce, avant de répondre.

Vous pouvez alors choisir de faire apparaître le numéro d'identification de votre radio (au moyen d'une page Avis d'appel) sur la radio que vous appelez pour que la personne puisse retourner votre appel. Le fonctionnement optimisé pour les appels privés est similaire au fonctionnement du téléphone.

1 Appuyez sur /

jusqu'à ce que CALL s'affiche.

2 Appuyez sur l (touche programmable

sous CALL).

3 L'affichage indique

le dernier numéro d'identification émis ou reçu.

4 Appuyez sur ,. 5 L'affichage indique le

numéro d'identification de votre radio.

PLANT POLICE

ZONE

MUTE

CALL

ID: 722588

MY ID:741317

6 Appuyez sur pour

que la radio revienne à l'affichage initial.

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 24 Tuesday, May 29, 2007 3:01 PM

Page 95

FONCTIONS

PARTAGÉES

Répondre à un appel privé

Remarque : Si vous appuyez sur le bouton de

conversation PTT avant d'appuyer sur le bouton de réponse d'appel, la réponse est transmise à quiconque dans le groupe de conversation (fonctionnement en mode de distribution).

• Après avoir répondu à un appel privé, le

numéro d'identification de l'appelant est enregistré dans votre radio comme étant le « dernier numéro d'identification reçu ».

• Si votre radio est configurée pour Private

Call II (Appel privé), à réception d'un appel pour conversation privée, deux tonalités d'avis sont émises et elles sont suivies de la voix reçue.

1 Lorsque vous recevez

un appel pour une conversation privée, deux tonalités d'avis sont émises (elles sont répétées toutes les 5 secondes pendant 20 secondes).

Alternance entre

2 Le voyant vert et l'avertisseur d'état d'appel

reçu, F

, clignoteront pour indiquer qu'un appel

a été reçu. Vous avez 20 secondes pour répondre à l'appel avant que la radio revienne automatiquement à l'affichage initial.

3 Appuyez sur le bouton de réponse d'appel ou

sur le bouton d'appel.

4 L'affichage indique le

numéro d'identification de l'appelant et l'avertisseur d'appel reçu s'éteint.

5 Après avoir visualisé le numéro d'identification

de l'appelant, vous pouvez décider de parler en privé (allez à l'étape suivante) ou de ne pas répondre à l'appel en appuyant sur le bouton de réponse d'appel ou sur le bouton d'appel pour revenir à l'affichage initial.

CALL RECEIVED

PLANT POLICE

ID: 722588

6 Si vous décidez de répondre à l'appel,

appuyez sur le bouton de conversation PTT.

7 Le numéro

d'identification de l'appelant reste affiché pendant la durée de l'appel.

8 Lorsque votre conversation est terminée,

appuyez sur ou sur le bouton de réponse d'appel pour raccrocher.

9 La radio revient à

l'affichage initial.

ID: 722588

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 25 Tuesday, May 29, 2007 3:01 PM

Page 96

FONCTIONS

PARTAGÉES

Passer un appel privé

Passer un appel privé se déroule en quatre phases :

• initier un appel privé,

• entrer le numéro d'identification de la radio souhaitée

• envoyer le numéro d'identification de la radio et

• tenir une conversation, puis raccrocher.

Initier un appel privé

Entrer le numéro d'identification de la radio souhaitée

Si le dernier numéro d'identification appelé est le numéro souhaité, allez directement à l'étape 5.

Pour entrer un nouveau numéro

Remarque : Six chiffres exactement doivent être

entrés pour le numéro d'identification de la radio. Si vous entrez moins de six chiffres, vous entendrez une tonalité d'erreur et l'affichage indiquera « INVALID ENTRY » (entrée invalide) lorsque vous tenterez d'envoyer le numéro d'identification de la radio. Vous entendrez également une tonalité d'erreur si vous essayez d'entrer sept chiffres.

• Une fois que vous avez commencé à

entrer les numéros, la touche , fonctionne comme la touche de retour en arrière d'un espace. Si vous appuyez sur cette touche, le dernier chiffre entré sera effacé et le curseur se déplacera vers la gauche. Une fois le dernier chiffre effacé, si vous appuyez à nouveau sur cette touche, le dernier numéro d'identification émis ou reçu s'affiche ; le fait d'appuyer sur / montre le premier membre de la liste.

1 Appuyez sur /

jusqu'à ce que CALL s'affiche.

2 Appuyez sur l (touche programmable

sous CALL).

3 L'affichage indique

le dernier numéro d'identification émis ou reçu.

4a Entrez le nouveau numéro d'identification à

six chiffres en utilisant le clavier.

ZONE

MUTE

CALL

ID: 722588

4b Sur l'affichage, l'ancien numéro

d'identification disparaît et les nouveaux chiffres apparaissent au fur et à mesure qu'ils sont entrés.

4c Le curseur clignote indiquant l'emplacement

des prochains numéros à entrer.

20L01-A_PR_UG_MTX4500.book Page 26 Tuesday, May 29, 2007 3:01 PM

Page 97

FONCTIONS

PARTAGÉES

Pour entrer un numéro à partir de la liste d'appels

Pour entrer un numéro à partir d'un emplacement de la liste d'appel

Remarque : Le dernier membre de la liste est

également « le dernier numéro d'identification émis ou reçu » à la position « 00 » sur la liste.

• Si vous entrez un numéro d'emplacement

qui n'existe pas (par exemple, « 15 »), l'affichage indique « INVALID ENTRY », la radio émet une tonalité d'appui invalide sur une touche et revient à l'étape 4b de cette procédure.

4a Appuyez sur , ou /.

4b / vous fait avancer au premier membre

ou au membre suivant de la liste; , vous fait revenir au dernier membre ou au membre précédent de la liste.

4c Lorsque vous êtes

positionné sur un membre de la liste, l'affichage montre alternativement le nom du membre et le numéro d'identification.

Alternance entre

4a Appuyez sur , ou sur / pour consulter

la liste d'appel.

4b Entrez le premier chiffre du numéro

d'emplacement. Si moins de 10 membres figurent dans la liste, allez directement à l'étape 4e.

CK TANG

ID: 784116

4c Si la liste comporte 10 membres ou plus,

l'affichage indique « ID LOC#X_ » (où X est le premier chiffre). Le curseur clignote pour indiquer l'emplacement du deuxième chiffre.

4d Entrez le deuxième chiffre du numéro

d'emplacement.

4e La radio passe à cette

position dans la liste. L'affichage montre alternativement le nom du membre et le numéro d'identification.

Alternance entre

CK TANG

ID: 784116

20L01-A_PR_UG_MTX4500.book Page 27 Tuesday, May 29, 2007 3:01 PM

Page 98

FONCTIONS

PARTAGÉES

Envoyer le numéro d'identification de la radio

Remarque : Si la radio que vous appelez n'est pas

en service, vous n'entendrez pas la sonnerie et l'affichage indiquera “NO ACK”. Allez à l'étape 10 pour raccrocher.

• Si votre radio est configurée pour Private

Call II, vous n'entendrez pas la sonnerie de type téléphone. Mais au lieu de cela, vous pourrez procéder à la conversation avec la partie appelée.

Converser puis raccrocher.

Remarque : Une fois que vous avez engagé une

conversation privée, si la radio est laissée en attente pendant plus d'une minute, un avis d'avertissement momentané est émis toutes les six secondes pour vous rappeler que des appels de distribution sont entendus. Après deux minutes, une tonalité de mode invalide permanente est émise.

Laisser une page Avis d'appel

5 Appuyez sur le bouton de conversation PTT

pour émettre le numéro d'identification.

6 Si la radio que vous appelez et dans les airs,

vous entendrez une sonnerie de type téléphone pendant 20 secondes ou jusqu'à ce que la radio appelée réponde à l'appel.

7 Si la partie que vous

appelez ne répond pas à l'appel dans les 20 secondes, la sonnerie du téléphone s'arrête et une tonalité d'avis est émise.

À ce stade, vous pouvez envoyer une page Call Alert

page ou aller à l'étape 10 pour

raccrocher.

8 Si la partie que vous appelez répond à l'appel,

vous entendrez sa voix.

NO ANSWER

9 Appuyez sur le bouton de conversation PTT

pour converser avec la personne appelée.

10 Lorsque votre conversation est terminée ou si

la radio que vous avez appelée ne répond pas ou n'est pas en service, appuyez sur pour raccrocher.

11 La radio revient à

l'affichage initial.

1 Si la partie avec laquelle vous voulez avoir un

appel privé ne répond pas à l'appel dans les 20 secondes, vous pouvez choisir de laisser une page Call AlertMC. Ceci laisse le numéro d'identification de votre radio sur la radio appelée pour que la personne puisse vous rappeler ultérieurement.

PLANT POLICE

20L01-A_PR_UG_MTX4500.book Page 28 Tuesday, May 29, 2007 3:01 PM

Page 99

FONCTIONS

PARTAGÉES

FONCTIONNEMENT AVIS D'APPEL

Répondre à une page Avis d'appel avec un Appel de groupe

Remarque : Lorsque vous recevez une page Avis

d'appel, vous pouvez entrer en mode Appel privé et appeler la radio qui essaie de vous contacter en utilisant le dernier numéro d'identification reçu.

Passer un Avis d'appel

Passer un avis d'appel se déroule en trois phases :

• initier un avis d'appel,

• entrer le numéro d'identification de la radio à contacter et

• envoyer l'avis d'appel.

2 Appuyez sur le bouton de conversation PTT

pour envoyer la page Avis d'appel. Vous entendrez cinq tonalités indiquant que le système a reçu votre numéro d'identification et que la radio que vous appelez est dans les airs.

3 Appuyez sur . 4 La radio revient à

l'affichage initial.

1 À réception d'une page Avis d'appel, quatre

tonalités d'avis sont émises (elles sont répétées toutes les 5 secondes).

2 Le voyant vert s'allume et l'avertisseur Appel

reçu, F, clignote indiquant qu'un appel a été reçu.

3 Appuyez sur le bouton de conversation PTT

pour répondre à la page.

PLANT POLICE

4 L'écran affiche le groupe

de conversation en cours. L'avis audible, le voyant d'avis et l'avertisseur d'appel reçu s'éteignent.

5 Le numéro d'identification de la radio qui a

cherché à vous contacter est enregistré comme étant « le dernier numéro d'identification reçu ».

6 Conversez de manière normale ; tous les

membres du groupe de conversation entendront votre réponse. Appuyez sur le bouton de conversation PTT pour parler ; relâchez-le pour écouter.

FIRE DEPT

20L01-A_PR_UG_MTX4500.book Page 29 Tuesday, May 29, 2007 3:01 PM

Page 100

FONCTIONS

PARTAGÉES

Initier un avis d'appel

Remarque : La même liste est partagée par les

fonctions Avis d'appel et Conversation privée.

• Si votre radio a été programmée de cette

manière, vous pouvez appuyer sur le bouton Page pour obtenir un accès rapide à la fonction Avis d'appel. Ceci vous amène directement à l'étape 3.

Entrer le numéro d'identification de la radio à contacter

Si le dernier numéro d'identification appelé ou reçu est le numéro souhaité, allez directement à l'étape 5.

Pour entrer un nouveau numéro

Remarque : Six chiffres exactement doivent être

entrés pour le numéro d'identification de la radio. Si vous entrez moins de six chiffres, vous entendrez une tonalité d'erreur lorsque vous tenterez d'envoyer le numéro d'identification de la radio. Vous entendrez également une tonalité d'erreur si vous essayez d'entrer sept chiffres.

• Une fois que vous avez commencé à

1 Appuyez sur /

jusqu'à ce que PAGE s'affiche.

2 Appuyez sur l (touche programmable

sous PAG E).

3 L'affichage indique

le dernier numéro d'identification émis ou reçu.

4a Entrez le nouveau numéro d'identification à

six chiffres en utilisant le clavier.

PAGE

PHON

VIEW

ID: 722588

4b Sur l'affichage, l'ancien numéro

d'identification disparaît et les nouveaux chiffres apparaissent au fur et à mesure qu'ils sont entrés.

4c Le curseur clignote indiquant l'emplacement

des prochains numéros à entrer.

20L01-A_PR_UG_MTX4500.book Page 30 Tuesday, May 29, 2007 3:01 PM

Motorola MTX1550, MTX4550 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual