Motorola MPMC101 User Manual
MPMC101
PMC SCSI-2 Adapter
User’s Manual
PMC101A/UM1
Notice
While reasonable efforts have been made to assure the accuracy of this document,
Motorola, Inc. assumes no liability resulting from any omissions in this document,
or from the use of the information obtained therein. Motorola reserves the right to
revise this document and to make changes from time to time in the content hereof
without obligation of Motorola to notify any person of such revision or changes.
No part of this material may be reproduced or copied in any tangible medium, or
stored in a retrieval system, or transmitted in any form, or by any means, radio,
electronic, mechanical, photocopying, recording or facsimile, or otherwise,
without the prior written permission of Motorola, Inc.
It is possible that this publication may contain reference to, or information about
Motorola products (machines and programs), programming, or services that are
not announced in your country. Such references or information must not be
construed to mean that Motorola intends to announce such Motorola products,
programming, or services in your country.
Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S.
Government, the following notice shall apply unless otherwise agreed to in
writing by Motorola, Inc.
Use, duplication, or disclosure by the Government is subject to restrictions as set
forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer
Software clause at DFARS 252.227-7013.
Motorola, Inc.
Computer Group
2900 South Diablo Way
Tempe, Arizona 85282
Preface
The information in this manual is adapted from the
UserÕs Guide
This manual describes the PCI and PMC SCSI-2 adapters, the installation of the
adapters into a motherboard, and the installation of the PCI software drivers.
Please note that only the MPMC101 Single-ended PMC SCSI-2 Adapter is
currently supported by Motorola.
The terminology and structure of this manual are directed to system
administrators, or those with equivalent technical experience.
The manual is organized as follows:
Chapter 1,
adapters, product features, and system requirements. Brief overviews for the PCI
bus and the SCSI-2 architectures are provided at the end of the chapter.
Chapter 2,
installing the PCI Adapter in a PCI bus-based user stations and servers. Installation
of the PMC Adapter into motherboards that support a PMC mezzanine
architecture is discussed in the latter sections of the chapter.
Chapter 3,
operating system, and step-by-step instructions for installing the PCI SCSI-2
Driver for the
, Interphase part number UG05520-000.
Introduction
Hardware Installation, provides step-by-step instructions for
Software Driver Installation
Windows NT
, provides general information about the PCI SCSI-2
, provides a guide for conÞguring the AIX
operating systems.
4520/5520 PCI SCSI-2 Adapter
Chapter 4,
with the installation or with the operation of the adapters.
Appendix A,
for the adapters.
Glossary
activity and functions.
Troubleshooting, provides tips and suggestions when having problems
SpeciÞcations
, A collection of common acronyms and terms used in describing SCSI
, provides operating criteria and environmental limits
Related Documentation
The
NCR 53C8XX ProgrammerÕs Reference Guide
in this document. You may purchase this document by contacting your local
Motorola sales ofÞce.
¨
Motorola
and the Motorola symbol are registered trademarks of Motorola, Inc.
Interphase¨ is a registered trademark of Interphase Corporation, Inc.
All other products mentioned in this document are trademarks or registered
trademarks of their respective holders.
© Copyright Motorola, Inc. 1995
All Rights Reserved
Printed in the United States of America
November 1995
(part number J109311) is referenced
Acronyms and Terminology
The following acronyms and terminology are often used in this manual instead of
the complete title or name:
AEN Asynchronous Event Notification
CCB Command Control Block
CCS Command Control Set
CDB Command Descriptor Block
CPU Central Processing Unit
DMA Direct Memory Access
ISA Industry Standard Architecture
LU Logical Unit
LUN Logical Unit Number
MIC Media Interface Connector
PCI Peripheral Component Interface
SCB SCSI Control Block
SCSI Small Computer System Interconnect
For extended deÞnitions of the above and other common computer and SCSI
terms, please refer to the
Glossary
at the end of this UserÕs Guide.
Conventions
The following conventions are used in this manual. Computer-generated text is
shown in typewriter font. Examples of computer-generated text are: program
output (such as the screen display during the software installation procedure),
commands, directory names, Þle names, variables, prompts, and sections of
program code.
Computer-generated text example
Commands to be entered by the user are printed in
example:
cd /usr/tmp
Pressing the return key (
assumed, when not explicitly shown. For example:
/bin/su
is the same as:
/bin/su ↵ Return
Input required by the user, when mixed with program output, is printed in
courier
standard UNIX conventions.
When a user command, system prompt, or a system response is too long to Þt on
a single line in this userÕs guide it will be shown as
with a backslash at the beginning of the continued lined or with a backslash at the
end of the previous line.
type. References to UNIX programs and manual page entries follow the
Do you want the new kernel moved into
\ vmunix?[y]
↵
Return
) at the end of the command line entry is
bold courier
type. For
bold
Safety Summary
Safety Depends On You
The following general safety precautions must be observed during all phases of operation, service, and
repair of this equipment. Failure to comply with these precautions or with speciÞc warnings elsewhere in
this manual violates safety standards of design, manufacture, and intended use of the equipment.
Motorola, Inc. assumes no liability for the customer's failure to comply with these requirements.
The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You,
as the user of the product, should follow these warnings and all other safety precautions necessary for the
safe operation of the equipment in your operating environment.
Ground the Instrument.
To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground.
The equipment is supplied with a three-conductor ac power cable. The power cable must either be plugged
into an approved three-contact electrical outlet or used with a three-contact to two-contact adapter, with
the grounding wire (green) Þrmly connected to an electrical ground (safety ground) at the power outlet.
The power jack and mating plug of the power cable meet International Electrotechnical Commission (IEC)
safety standards.
Do Not Operate in an Explosive Atmosphere.
Do not operate the equipment in the presence of ßammable gases or fumes. Operation of any electrical
equipment in such an environment constitutes a deÞnite safety hazard.
Keep Away From Live Circuits.
Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or
other qualiÞed maintenance personnel may remove equipment covers for internal subassembly or
component replacement or any internal adjustment. Do not replace components with power cable
connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To
avoid injuries, always disconnect power and discharge circuits before touching them.
Do Not Service or Adjust Alone.
Do not attempt internal service or adjustment unless another person capable of rendering Þrst aid and
resuscitation is present.
Use Caution When Exposing or Handling the CRT.
Breakage of the Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion).
To prevent CRT implosion, avoid rough handling or jarring of the equipment. Handling of the CRT should
be done only by qualiÞed maintenance personnel using approved safety mask and gloves.
Do Not Substitute Parts or Modify Equipment.
Because of the danger of introducing additional hazards, do not install substitute parts or perform any
unauthorized modiÞcation of the equipment. Contact your local Motorola representative for service and
repair to ensure that safety features are maintained.
Dangerous Procedure Warnings.
Warnings, such as the example below, precede potentially dangerous procedures throughout this manual.
Instructions contained in the warnings must be followed. You should also employ all other safety
precautions which you deem necessary for the operation of the equipment in your operating environment.
Dangerous voltages, capable of causing death, are
!
WARNING
present in this equipment. Use extreme caution when
handling, testing, and adjusting.
!
WARNING
This equipment generates, uses, and can radiate electromagnetic energy. It may cause or be susceptible to
electro-magnetic interference (EMI) if not installed and
used in a cabinet with adequate EMI protection.
Adapter Overview 1-1
Product Features 1-2
Supported Software Drivers 1-3
System Requirements 1-3
PCI Overview 1-4
Introduction to SCSI-2 1-5
Overview 2-1
Tools Required 2-1
Unpacking the Adapter 2-2
Installing the PCI SCSI-2 Adapter 2-3
Installing the PMC SCSI-2 Adapter 2-9
Connecting to the SCSI Bus 2-13
AIX Operating Systems 3-1
Windows NT Operating Systems 3-2
Installing the Windows NT Driver 3-2
Overview 4-1
Start-up 4-1
Boot-up 4-2
Applications 4-3
PCI and PMC Adapter 4-3
Hardware A-1
Environment A-2
Connectors and Cables A-2
SCSI ÒPÓ Cable Contact Assignments A-3
Contents
PCI SCSI-2 Adapter 1-1
Single Initiator, Single Target Systems 1-5
Target with Multiple Peripherals 1-6
Multiple Device ConÞguration 1-7
Desktop PCI Slot ConÞguration 2-4
Expansion Backplate Removal 2-4
Single-ended PCI Adapter 2-5
Differential PCI Adapter 2-6
Inserting the PCI Adapter Card 2-7
Adapter Card Installed to Chassis 2-8
Differential PMC SCSI-2 Adapter 2-9
Single-ended PMC SCSI-2 Adapter 2-9
Installing the PMC Adapter 2-10
SCSI Connector Port 2-14
Windows NT Setup 3-2
Windows NT Setup Options Menu 3-3
SCSI Adapter Setup 3-3
Setup Message 3-4
Select SCSI Adapter Option 3-4
Select SCSI Adapter Option 3-5
Installed Adapter Listing 3-5
Installed Adapter Listing 3-6
Restart Message 3-6
List of Figures
PCI SCSI-2 Adapter Jumper Settings 2-6
PMC SCSI-2 Adapter Jumper Settings 2-12
Connector and Cable Requirements 2-13
Start-up Problems 4-1
Bootup Problems 4-2
Application Problems 4-3
PCI and PMC Adapter Problem 4-3
List of Tables
xi
xii
Adapter Overview
1Introduction
1
Note
The PCI Adapter is a single slot, fast and wide SCSI-2 (Small
Computer System Interface - 2) that provides high throughput
connectivity for open systems applications. The PMC Adapter
provides the same level of performance for workstations with
embedded PMC (PCI Mezzanine Card) slots.
Though this manual covers the PMC and PCI
single-ended and differential SCSI-2 adapters, only the
MPMC101 Single-ended PMC SCSI-2 Adapter is
currently supported by Motorola.
Jumpers
JA1, JA2, JA3
Face
Plate
68-pin SCSI
Connector
PCI
Connector
Figure 1-1. PCI SCSI-2 Adapter
1-1
1
Introduction
Combined with a 32-bit/33-MHz PCI (Peripheral Component
Interconnect) interface into local CPU memory, the adapters
provide a total wide and fast pathway for data, which is especially
important for servers, image processing, high-speed networks, and
other high performance peripherals. They are designed to operate
within the framework of todayÕs open systems architectures by
providing physical and data-link services as defined by the ANSI
X3.131 specifications for SCSI-2.
Product Features
The PCI and PMC Adapters are available with the following
capabilities:
Compliant with PCI Local Bus, version 2.1
❏
32-bit, zero wait state PCI DMA master
❏
Up to 132 Mbps burst DMA rate
❏
1-2
20 Mbps Fast and Wide SCSI-2
❏
Differential or Single-ended SCSI-2 interfaces
❏
Support for up to 30 devices from a single slot
❏
64K EPROM for Network Boot or BIOS Firmware
❏
The PCI and PMC Adapters are plug-and-play devices with
systems that are compliant with the PCI Local Bus Revision 2.1
specification. Systems that are not compliant may require manual
configuration via a PCI Device Configuration menu in the BIOS.
Refer to your host systemÕs documentation for PCI Device
Configuration
Supported Software Drivers
The software drivers for the PCI and PMC Adapters are contained
in the Windows NT 3.51 and the AIX 4.1 operating systems,
respectively.
Supported Software Drivers
1
The PMC Adapter and the PCI Adapter use the same
software drivers. Whether the adapter is installed to a
PCI slot (PCI Adapter) or to a PMC mezzanine slot
(PMC Adapter), the selection of a driver is based upon
the operating system in use by the host computer; not
by the configuration of the system hardware.
!
Caution
Note
The PCI and PMC Adapters are sensitive to static
electricity. Do not touch any components or metal parts
without using a grounding strap. To prevent damage
from electrostatic discharge, handle the adapter only
while wearing a grounding strap.
System Requirements
Minimum system requirements to operate the PCI and PMC
Adapters are as follows:
Hardware:
❏
Ð Power PC systems operating under Windows NT 3.51 or
later
Ð Power PC systems operating under AIX 4.1 or later
Bus Architecture:
❏
Ð The I/O interface must comply to PCI Local Bus
specification Revision 2.0 or greater
16MB total system memory.
❏
1-3
1
Introduction
PCI Overview
Peripheral Component Interconnect (PCI) was developed by IntelÕs
Architecture Lab, along with leading computer vendors, to
overcome the bottlenecks associated with traditional 16-bit
expansion slots, operating at 8 MHz, or essentially 5 megabytes per
second. The result was a local bus system capable of transferring 32
bits of data at 33 MHz for a maximum data transfer rate of 132
megabytes per second. The PCI Local Bus takes peripherals off the
I/O bus and connects them together with the CPU and the memory
subsystem. This provides a wider, faster pathway for data, which is
especially important for servers, graphic-intensive software,
high-speed networks, and other high performance peripherals.
Features of the PCI Local Bus architecture include:
Processor-independent bridge, between the CPU and
❏
high-speed peripherals, that serves as a traffic controller
between busses.
32-bit memory addressing for CPU, Direct Memory Access
❏
(DMA) devices and bus masters.
1-4
32-bit data transfers at 33 MHz for CPU, DMA and bus
❏
master devices.
132 Mbps maximum data transfer rate.
❏
Data is written and read from the peripherals in linear busts
❏
at every clock cycle.
Buffers located between the peripherals and the CPU that
❏
allows multiple, high-speed peripherals to be attached to the
same PCI local bus.
Automatic translation of bus cycles between PCI and the
❏
traditional I/O slots for EISA, ISA, and MicroChannel busses.
❏
Automatic configuration of system and expansion boards.
Introduction to SCSI-2
SCSI (Small Computer System Interface) is an I/O bus protocol that
provides high performance, peer-to-peer data communications for
up to 16 devices, including one or more host computers. The main
advantage for using SCSI-2 is that all the initialization information
is stored within the SCSI-2 device. The hostÕs operating system can
obtain all the pertinent information about the device without
referencing external setup files or software drivers.
Introduction to SCSI-2
1
Host Computer
Computer
Host
Adapter
SCSI BUS
Controller
Figure 1-2. Single Initiator, Single Target Systems
Disk Drive
SCSI
Peripheral
1-5
1
Introduction
In a SCSI-2 system, a computer with a host-adapter serves as the
primary initiator for all actions on the SCSI bus. All other devices
connected to the bus are SCSI targets. Figure 1-2 above illustrates a
simple configuration where a host computer is connected to a
single target, a disk drive with an embedded SCSI controller. The
controller can be a stand-alone device with multiple peripherals as
shown in Figure 1-3.
SCSI Controller
Host Computer
Computer
Host
Adapter
SCSI BUS
SCSI
Controller
Printers
Peripheral
Peripheral
Peripheral
Peripheral
1-6
Figure 1-3. Target with Multiple Peripherals
Loading...