Motorola I465, Mike i465 User Manual

Download

TELUS

i465 Mike Phone

User’s Guide

DECLARATION OF CONFORMITY

Per FCC CFR 47 Part 2 Section 2.1077(a)

Responsible Party Name: Motorola, Inc. Address: 8000 West Sunrise Boulevard

Plantation, FL 33322 USA

Phone Number: 1 (800) 453-0920 Hereby declares that the product: Product Name: i465 Model Number: H98XAH6JR7AN FCC-ID: IHDT56KB1 Conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)

FCC Notice to Users

The following statement applies to all products that have received FCC approval. Applicable products bear the FCC logo, and/or an FCC ID in the format FCC-ID: IHDT56KB1 on the product label.

Motorola has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. See 47 CFR Sec. 15.21.

Class B Digital Device

As a personal computer peripheral, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Sec. 15.19(3).

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Notice to Users

Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device. See RSS-GEN 7.1.5.

Motorola, Inc. Consumer Advocacy Office 600 North US Highway 45 Libertyville, IL 60048

www.hellomoto.com

Note:

Do not ship your phone to the above address. If you need to return your phone for repairs, replacement, or warranty service, please contact the Motorola Customer Support Center at:

1-800-453-0920 (United States) 1-877-483-2840 (TTY/TDD United States for hearing impaired)

Certain mobile phone features are dependent on the capabilities and settings of your service provider’s network. Additionally, certain features may not be activated by your service provider, and/or the provider's network settings may limit the feature’s functionality. Always contact your service provider about feature availability and functionality. All features, functionality, and other product specifications, as well as the information contained in this user's guide are based upon the latest available information and are believed to be accurate at the time of printing. Motorola reserves the right to change or modify any information or specifications without notice or obligation.

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. Java and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.

HELLOMOTO

Introducing your new Motorola wireless phone. Here’s a quick anatomy lesson.

Left Soft Key

Perform function

in lower left

display.

Right Soft Key

Perform function in lower right display.

End/Power Key

End calls, exit menu system, turns phone on/off.

Talk Key

Make &

answer calls.

OK Key

In menus & lists, press to select highlighted option.

4-Way Navigation

Key

Speaker On/Off Key

Volume Keys

PTT Button

Audio Jack

Micro USB Connector

Connects charger

and accessories.

Camera Key

Web Key

Messaging Key

Menu Key

From home screen,

open main menu.

check it out

Voicemail LED

Text Message LED

Bluetooth LED

Press and hold the

Power Key for a

few seconds, or until

the screen lights up,

to turn on your phone.

Customizable r key

that can be used

to open the

Settings screen.

Press the Navigation key

up, down, left or right

to highlight a menu feature.

Press the r key to select.

turn it on & off

To turn on your phone, press and hold . for a few seconds or until the display turns on. If prompted, enter your four-digit unlock code.

To turn off your phone, press and hold

for

two seconds.

Note:

If you press the . for more than four

seconds, the handset will power “On” in

Transmitters Off

mode. See “transmitters” on

page 42.

contents

check it out . . . . . . . . . . . 2

turn it on & off . . . . . . . 2

menu map. . . . . . . . . . . . 6

use and care . . . . . . . . . . 8

essentials . . . . . . . . . . . . 9

about this guide . . . . . . 9

SIM card . . . . . . . . . . . 10

battery . . . . . . . . . . . . 10

enable security . . . . . . 14

make a phone call. . . . 14

answer a phone call . . 14

advanced calling . . . . . 15

make a private call . . . 15 answer a private call . . 16 store a phone number

or private ID . . . . . . . . 17

contacts . . . . . . . . . . . 17

call a stored phone number or private ID . 18 your phone number

and private ID . . . . . . . 18

messaging . . . . . . . . . 18

message groups. . . . . 19

mms features . . . . . . . 21

inbox. . . . . . . . . . . . . . 25

outbox . . . . . . . . . . . . 30

sent items . . . . . . . . . 30

customize messaging. 31 using your handset

as a modem . . . . . . . . 36

basics. . . . . . . . . . . . . . . 37

display . . . . . . . . . . . . 37

main menu . . . . . . . . . 38

text entry . . . . . . . . . . 38

volume . . . . . . . . . . . . 41

navigation key. . . . . . . 41

handsfree speaker . . . 41

transmitters . . . . . . . . 42

use GPS with map

software . . . . . . . . . . . 42

features for the

hearing impaired. . . . . 42

TTY . . . . . . . . . . . . . . . 44

security features. . . . . 44

main attractions . . . . . . 45

media center . . . . . . . 45

video player . . . . . . . . 46

camera . . . . . . . . . . . . 46

PTX features . . . . . . . . 49

one touch PTT . . . . . . 56

PT manager . . . . . . . . 57

Bluetooth® . . . . . . . . . 57

contents

call features . . . . . . . . . . 61

turn off a call alert . . . . 61

recent calls . . . . . . . . . 61

redial . . . . . . . . . . . . . . 62

caller ID . . . . . . . . . . . . 62

call forward . . . . . . . . . 62

voice names . . . . . . . . 63

emergency calls . . . . . 64

international calls. . . . . 64

speed dial . . . . . . . . . . 65

voicemail . . . . . . . . . . . 65

net alerts . . . . . . . . . . . 66

Mike’s Talk Around TM . 67

switching to Mike’s

Talk Around . . . . . . . . . 68

exiting Mike’s Talk

Around. . . . . . . . . . . . . 68

channels and codes . . . 68 private Mike’s Talk

Around calls. . . . . . . . . 71

making emergency calls while in Mike’s Talk AroundTM mode . . 73

setup options. . . . . . . . 73

customize. . . . . . . . . . . . 75

ring tones . . . . . . . . . . 75

backlight . . . . . . . . . . . 76

LED indicators . . . . . . . 76

wallpaper . . . . . . . . . . . 77

datebook . . . . . . . . . . . 77

hide or show location

information . . . . . . . . . 79

Legal and Safety . . . . . . 81

Safety and General

Information . . . . . . . . . 81

Operational

Precautions . . . . . . . . . 82

RF Energy Interference/

Compatibility . . . . . . . . 82

Bluetooth. . . . . . . . . . . 83

Caring for the Environment by

Recycling . . . . . . . . . . . 84

Driving Precautions . . . 84 Operational Warnings . 84 Service and Repairs. . . 86 Export Law

Assurances . . . . . . . . . 87

Battery Use and

Safety . . . . . . . . . . . . . 87

Battery Charging . . . . . 88

Specific Absorption

Rate . . . . . . . . . . . . . . . 88

AGPS and Emergency

Calls. . . . . . . . . . . . . . . 89

Motorola Limited Warranty for the United States

and Canada . . . . . . . . . 90

Hearing Aid Compatibility With

Mobile Phones . . . . . . 94

contents

Information From the World Health

Organization . . . . . . . . 95

Product Registration . . 95 Wireless: The New

Recyclable . . . . . . . . . 95

California Perchlorate

Label. . . . . . . . . . . . . . 95

Patent and Trademark

Information . . . . . . . . . 96

Software Copyright

Notice . . . . . . . . . . . . . 96

Privacy and Data

Security . . . . . . . . . . . 96

Smart Practices While

Driving . . . . . . . . . . . . 97

index . . . . . . . . . . . . . . . 99

menu map

Browser

Java Apps

• Java System

Messages

• [Create Message]

•Voice Mail

• Net Alert

• Inbox

•Drafts

• Outbox

• Fax Mail

• Sent Items

Shop

Contacts

• [New Contact]

Call Alert

Ring Tones

• Vibrate All: On/Off

• Ringer

• Vibrate

• Silent

Settings

• (see next page)

Bluetooth

• Hands Free

• Link to Devices

• Device History

• Setup

• Find Me

Recent Calls

Profiles

My Info

•My Name

• Line 1

• Line 2

• Private ID

• Group ID

• Carrier IP

• IP1 Address

• IP2 Address

Datebook

Vo iceRecord

• [New VoiceRec]

Call Forward

GPS

• Position

•Privacy

• Interface

Shortcuts

•[New Entry]

• 1)Shortcuts

• 2)Cntcs[New Con...]

• 3)Recent Calls

• 4)Contacts

• 5)Datebook

• 6)Messages

• 7)VoiceRecord

•8)Browser

• 9)Call Forward

Memo

PT Manager

• Send Message

• Send Picture

• Send Event

• Send My Info

• Send Contact

• Configure

Call Timers

• Last Call

• Phone Reset

• Phone Lifetime

•Prvt/Grp Reset

• Prvt/Grp Life

• Kbytes Reset

Talk Around

• Go To Talk Around

• Setup

•Help

Camera

Media Center

This is the standard Main Menu layout. Your phone’s menu may be a little different.

main menu

Display/Info

• Wallpaper

•Text Size

• Theme

• Home Icons

• Backlight

•Clock

• Menu View

• Large Dialing

• Language

Phone Calls

• Set Line

•Any Key Ans

• Auto Redial

• Call Waiting

•Auto Ans

• Minute Beep

• Call Duration

• TTY

•Hearing Aid

• Notifications

• DTMF Dialing

• Prepend

2-Way Radio

• Tkgrp Silent

•Tkgrp Area

• One Touch PTT

• Alert Type

•PTT Quick Notes

•On/Off PTT

• Store Rcvd Info

• PTT Backlight

Personalize

• Menu Options

•Up Key

•Down Key

•Left Key

•Right Key

• Center Key

• Left Sftkey

•Right Sftkey

•Power Up

Vo lu me

•Line 1

•Line 2

• Messages

• Earpiece

•Speaker

•Keypad

• Java Earpiece

• Java Spkr

•Data

Security

• Phone Lock

• Keypad Lock

• SIM PIN

• GPS PIN

• Change Passwds

Advanced

• Alert Timeout

• Headset/Spkr

• Connectivity

• Reset Defaults

• Return to Home

• Transmitters

• Phone Only

• Baud Rate

settings menu

use and care

Use and Care

To care for your Motorola phone, please keep it away from:

liquids of any kind dust and dirt

Don’t expose your phone to water, rain, extreme humidity, sweat, or other moisture. If it does get wet, don’t try to accelerate drying with the use of an oven or dryer, as this may damage the phone.

Don’t expose your phone to dust, dirt, sand, food, or other inappropriate materials.

extreme heat or cold cleaning solutions

Avoid temperatures below 0°C/32°F or above 45°C/113°F

To clean your phone, use only a dry soft cloth. Don’t use alcohol or other cleaning solutions.

microwaves the ground

Don’t try to dry your phone in a microwave oven.

Don’t drop your phone.

essentials

Caution:

Before using the phone for the first time, read the Important Safety and Legal information included in the gray-edged pages at the back of this guide.

about this guide

This guide shows how to locate a menu feature as follows:

Find it: / > u >

Phone Calls

This means that, from the home screen:

Press the menu key / and then press the

Settings

menu option u.

Press the navigation keys ; to scroll to

Phone Calls

, and press the center key r to

select it.

symbols

This means a feature is network or

subscription dependent and may not be available in all areas, or might not be offered by your service provider. Contact customer service for more information.

This means a feature requires an

optional accessory.

essentials

SIM card

insert the SIM card

Warning:

To avoid loss or damage, do not remove your SIM card from your phone unless absolutely necessary.

battery

Battery Use & Battery Safety

• Motorola recommends you always use Motorola-branded batteries and chargers.

The warranty does not cover damage caused by non-Motorola batteries and/or chargers.

Caution:

Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard. Improper battery use, or use of a damaged battery, may result in a fire, explosion, or other hazard.

•

Battery usage by children should be supervised.

•Important

: Motorola mobile devices are designed to work best with qualified batteries. If you see a message on your display such as

Invalid

essentials

Battery

Unable to Charge

, take the

following steps:

•

Remove the battery and inspect it to confirm it bears a Motorola “Original Equipment” hologram;

•

If there is no hologram, the battery is not a qualified battery;

•

If there is a hologram, replace the battery and retry charging it;

•

If the message remains, contact a Motorola Authorized Service Center.

•

New batteries or batteries stored for a long time may take more time to charge.

•Charging precautions:

When charging your battery, keep it near room temperature. Never expose batteries to temperatures below 0°C (32°F) or above 45°C (113°F) when charging.

Always take your mobile device with you when you leave your vehicle.

•

When storing your battery, keep it in a cool, dry place.

•

It is normal over time for battery life to decrease, and for the battery to exhibit shorter runtime between charges or require more frequent or longer charging times.

•Avoid damage to battery and mobile device.

Do not disassemble, open, crush, bend, deform, puncture, shred, or submerge the battery or mobile device. Avoid dropping the battery or mobile device, especially on a hard surface. If your battery or mobile device has been subjected to such damage,

take it to a Motorola

Authorized Service Center

before

using.

Do not

attempt to dry it with an

essentials

appliance or heat source, such as a hair dryer or microwave oven.

• Use care when handling a charged battery:

Particularly when placing it inside a pocket, purse, or other container with metal objects. Contact with metal objects (e.g., jewelry, keys, beaded chains) could complete an electrical circuit (short circuit), causing the battery to become very hot, which could cause damage or

injury.

Promptly dispose of used batteries in accordance with local regulations. Contact your local recycling center for proper battery disposal.

Warning:

Never dispose of batteries in a fire

because they may explode.

battery installation

Pull out the connector cover. Slide the battery door downwards until it is released from the phone.

essentials

battery charging

New batteries are not fully charged.

charge using the charger

Pull out the connector cover, and insert the charger into the micro USB connector on your phone as shown.

charge from your computer

You can partially charge your phone’s battery by connecting a Motorola-approved USB cable from your phone’s micro-USB port to a high power USB connector on a

Remove the battery door.

Push the battery down until it snaps in place.

Replace the battery door and slide it up while pressing gently until you hear a click.

essentials

computer (not a low-power one, such as the USB connector on your keyboard or bus-powered USB hub). Typically, USB high-power connectors are located directly on your computer.

enable security

You must enable security the first time you power on you phone or within 10 days of first activation of your phone.

Press K under Ok.

You are prompted to enable security. Press

under

Yes

. A series of screens followed by the default home page displays.

Press . to return to the home screen.

make a phone call

Enter a phone number and press , or use a voice command. See “place a call using a voice name” on page 63.

To hang up press

answer a phone call

If you want to answer the call on speaker phone, press the speaker key

)

If you want to answer the call using the handset, press

. To hang up press ..

If you are using a Bluetooth headset, press the answer key on your headset. To hang up press the key again.

essentials

advanced calling make a private call

With Private calls service, you use your phone as a long-range, digital 2-way radio using one-to-one Private calls or one-to-many group calls.

Your Private ID is the number at which you receive one-to-one Private calls.

Talkgroup numbers are numbers through which you receive one-to-many group calls.

to make a Private call

Enter the Private ID you want to call.

Press and hold the PTT button. Begin talking after your phone emits a chirping sound.

Release the PTT button to listen.

To end the call press

Note:

A Private call ends automatically if there

is no activity on the call for a few seconds.

feature call waiting

To accept the second call and put the active call on hold press

under

Yes

To accept the second call and end the active call press

3-way call

Make or receive a phone call and press

3 Way

. Enter the second phone number, press

and K under

Join

You cannot make and other calls during a three-way call, even if one party hangs up.

any key answer

To answer phone calls by pressing any key on the keypad press

> u >

Phone Calls

Any Key Ans

> On.

essentials

send call alerts

Sending a call alert discretely lets the recipient know that you want to talk to him or her on a Private call.

When you send a call alert, the recipient’s handset displays your name and emits a series of beeps or vibrations.

to send a call alert

Enter the Private ID you want to call as you would when making a Private call.

Press K under

Alert

When the message

Ready To Alert

appears on the display, press the PTT button until the message

Alert Successful

appears.

answer a private call

When your phone emits a chirping sound or vibrates to indicate you are receiving a

Private call, wait for the caller to finish speaking.

Press and hold the PTT button and begin talking after your phone emits a chirping sound.

Release the PTT button to listen.

To end the call press ..

answer a call alert

When you receive a call alert, you must:

You cannot receive phone calls or Private calls until you do.

option

Answer:

Begin a Private call with the sender

using the PTT button.

Queue:

Store the call alert to the call alert

queue.

Clear:

Dismiss and delete the call alert.

essentials

to answer a call alert

Press the PTT button to start a Private call with the sender.

Queue the call alert by pressing K under

Queue

Clear the call alert by pressing K under

Clear

store a phone number or private ID

You can store a phone number or private ID in

Contacts

Find it: / > L >

[New Contact]

Enter a name for the new entry. Each entry’s name can contain 20 characters.

Select a specific

Ring Tone

Select a type for the entry (

Mobile, Private

Work1, Work2, Home, Email, Fax, Pager, Talkgroup, IP

Other

)

. To store a private ID choose

Private

Enter the number for the entry and press

under

Save

when done

contacts

feature edit/delete

contact entry

Press K under

Contcs

Select a contact and press

Edit

. Change the

desired content and press

. Press K under

Save

essentials

call a stored phone number or private ID

Find it: / > L.

Scroll to the

Contacts

entry.

If the Contacts entry contains more than one number, scroll left or right until the type of the number you want to call is displayed (

Mobile, Private, Work1, Work2, Home

etc.).

If you chose a phone number, press , to call the entry, or if you chose a Private ID

or Talkgroup ID, press and hold the PTT button to call the number.

your phone number and private ID

Find it: / >

My Info

messaging

Your phone has the ability to use both MOSMS and Multimedia Messaging Service (MMS) messaging. The type of messaging your phone uses will be determined by your service provider. If your service provider offers messaging through MOSMS, your phone sends and receive messages using MOSMS.

If your service provider offers MMS, your phone sends and receives messages using MMS. Additionally, MMS allows you to send

set ringer ID

Press K under

Contacts.

Select a contact and press

Edit

. Select

Ringer

and choose your desired ring tone. Press

under

Done

feature

essentials

and receive messages that may include text, pictures, videos, and audio files.

message groups

A Message Group allows you to send text or Multimedia Messaging Service (MMS) messages to Groups of up to 20 contacts.

Find it: / > L > [New Msg Group]

Select

[Add Member]

and select a contact.

When you are finished adding members to the group, press

under

Done

Type in a name for the Message Group in the

Name

field.

Note:

If you do not provide a name for the

Message Group, the default name will be

Msg Group

followed by the number of group members. For example, a Message Group with three members would be named

Msg Group (3)

Press K under

Save

viewing members of a message group

1 Press / > L, select the Message

Group and press r.

adding a member to a message group

Select the Message Group in Contacts and press

/ > Edit.

Select

[Add Member]

and press r. Select

the contact you want to add and press

under

Done

Press K under

Save

to save your changes.

essentials

removing a member from a message group

Select the Message Group in Contacts and press

/ > Edit.

Highlight the member you wish to remove and press

/ > Remove Member

deleting a message group

Press

/ > L

and select the Message

Group.

Press

/ > Delete Msg Group

. When

prompted, press

under

Yes

to delete,

under No to cancel.

create and send messages

From the home screen press K under

Mesgs

[Create Message]

Enter the phone number of the person you want to send the message to and press

or press K under

. Select

Contacts

Recent Calls

to find the number you

want and press

under

Done

Select

Mesg

: and enter the text of the

message or to use a quick note press

under

QNotes

and scroll to the quick note

you want.

If you want to send the message, press

under

Send

or to delete the message

without sending it, press

under

Cancel

quick notes

When you are filling in the

Message

and

Subject

fields, you can add ready-made words or short phrases called Quick Notes. After you add these words or phrases, you can edit them as you would any other text.

essentials

While you are creating a message, scroll to or select

Message

Subject

Press K under

QNotes

Select the quick note you want to insert into the message.

Press K under

Send

mms features

Note:

The following features are available only

when using MMS.

more message options

To view more message fields in a message you are creating, select

....More....

The following options become available:

insert a picture, video, and audio recording

You can insert one or more pictures, videos, and audio files from the media center into the body of the message. You can include text in the body of your message in addition to these items.

option

Subject

: Create or edit the subject line.

Attach

: Attach a picture, audio file or voice

record.

: Send a copy of this message to

someone else.

Auto Replies

: Allows you to create a list of possible short answers for the recipient to choose when replying to your message.

Priority

: Set priority

Normal

High

Valid Until:

Set a date after which attempts to

deliver the message end, or press

under

No Date

option

essentials

insert items

While you are filling in the

Mesg

field, press

, select

Insert

and choose from

Add Picture

Insert Audio, Insert Video, Capture Video, Capture Picture

Record Voice

A list of available pictures, videos, or audio files appears. You can only insert one item at a time.

Select the picture, video, or audio recording you want to insert.

remove an inserted item

To remove an item from the message you are creating, highlight it and press

under

Delete

attach a picture, video, or audio recording

You can attach one or more pictures, audio or voice recordings from your phone into the

body of the message. You can include text in the body of your message in addition to these items.

While you are filling in the

Attach

field,

press

[New]

> and select from

Browse Pictures,

Capture Picture

Browse Audio, Record Voice, Browse

Video

, or

Record Video

A list of available pictures, audio files, or voice recordings appears.

Select the picture, audio or voice record you want to attach.

If you want to attach more items, select

[New]

When finished, press K under

Done

Note:

You can only attach audio files and pictures if they are not forward locked and if their DRM settings do not prevent you from sending.

essentials

Forward locked items are usually copyright protected, and you cannot share them with anyone, such as in Private calls or by uploading them from your phone.

take a new picture

While you are creating a message, scroll to any message field and press

select

Attach

[New]

Select

Capture Picture

. This accesses the

camera.

Take the picture. For instructions on how to take the picture see

“camera” on

page 46.

When you have captured the picture you want, press

under

Save

To discard the picture, press K under

Discard

. You can then take another picture.

When finished, press K under

Done

The picture is attached to the message and saved to the default storage location.

record a video

You can record a video to send with a message:

Select

Attach > [New] > Record Video

Record and adjust video.

To view the video without saving it, press

under

Review

To save the video, press e or press r.

To discard the video without saving it, press

under

Discard

The video is attached to the message and saved to the media center in the default storage location.

essentials

create a new voice record

You can create a new voice record to send with a message:

Press / or select

Attach

[New]

Select

Record Voice

Say the message you want to record into the microphone.

When you are finished recording, press

When finished, press K under

Done

The voice record is attached to the message and saved to the media center and the list of voice records.

remove an attachment

To remove an attachment in a message you are creating:

Select

Attach

Scroll to the attachment you want to remove.

Press / >

Unattach

use drafts

When you save a message as a draft, it is saved in the drafts folder.

Find it:

Press / > E >

Drafts

Select the draft you want to edit.

To edit the fields you want to change, follow step

2 through step 4 in “create

and send messages” above.

delete a draft

When you send a draft, it is removed from the Drafts folder.

To delete a message in the Drafts folder without sending it, scroll to the message

essentials

you want to delete and press K under

Delete

Press K under

Yes to confirm.

inbox

Find it:

Press / > E >

Inbox

receive a message

To view the message press K under

Read

To dismiss the message notification press

under

Exit

While reading a text and numeric message that contains a phone number, you can press

to call that number.

threaded inbox

The threaded Inbox allows you to organize your messages by subject or sender.

From the Inbox, highlight a message.

Press / >

Threading

, and select from

None

Subject

, or

Sender

Note:

Threading by subject is dependant

upon your service provider.

read from the message center

From the home screen press K under

Mesgs

Inbox

Select the message you want to read.

To reply to the message, press K under

delete unread messages

Scroll to the message you want to delete.

Press K under

Delete

and K under

Yes

confirm.

essentials

forward a message

Press / >

Forward

Create and send your message. Embedded objects and attachments are included when you forward a message.

lock and unlock messages

Locked messages cannot be deleted until you unlock them.

View the message you want to lock or unlock.

Press / >

Lock Message

Unlock Message

call a number in a message

If a message you receive contains a phone number, Private ID, or Talkgroup ID in the

From

field, the

field, the Cc field, the

Subject

field, or the body of the message, you can call or send a call alert to that number.

send a call alert

View the message.

Highlight the Private ID or Talkgroup ID you want to alert.

Press / >

Alert

Push the PTT button.

make a group call

View the message.

Press /.

Highlight the Talkgroup ID you want to call.

Select

Talkgroup

Push the PTT button.

essentials

store message information to contacts

If a message you receive contains a phone number, Private ID, Talkgroup ID, or an email address in the

From

field, the To field, the Cc

field, the

Subject

field, or the body of the

message, you can store this information to

Contacts

View the message.

Highlight the number or email address you want to save.

Press / >

Save Number

Save Email

To store the number or email address as a new entry, select

[New Contact]

To store the number or email address to an existing entry, select the entry.

With the Contacts type field highlighted, press

;

left or right to display the

Contacts type you want to assign the number or email address.

Press K under

Save

reply to a message

To reply to a message:

View the message you want to reply to.

To reply to the sender only, press K under

or press K under

Reply All

reply to all recipients.

A list of short phrases appears. Select any of these phrases to add it to your messages or select

[Create Reply]

Edit any message fields you want to change.

Press K under

Send

essentials

use auto replies

If the message you are replying to was sent with auto replies, it contains a numbered list of possible replies for you to send. Press the number of the reply you want to send. The reply is sent immediately without further action.

go to a website

If a message contains one or more website URLs, you can go to that website.

View the message.

Highlight the website URL you want to go to.

Press

/ > Go To Website.

Note:

The entire URL must appear in the

message to allow you to open the website.

embedded objects and attachments

If a message contains pictures, videos, or audio files in the body of the message, highlight each picture, video, or audio recording to view or play it.

If a message contains a picture, video, or audio recording as an attachment, open the attachment to view the picture or play the video or audio recording.

open attachments

View the message.

Highlight the attachment you want to open. Attachments appear at the end of a message.

Press r.

Attachments of an unknown type cannot be opened, but can be deleted.

essentials

save an embedded picture, video, or audio recording

To save a picture, video, or audio recording that is part of the body of a message you receive:

View the message.

Highlight the picture, video, or audio recording you want to save.

Press /.

Select

Save Picture, Save Video

, or

Save Audio

The item will save in the default storage location.

delete an embedded picture, video, or audio recording

To delete a picture, video, or audio recording that is part of the body of a message you receive:

View the message.

Highlight the picture, video, or audio recording you want to delete and press /.

Select

Delete Picture, Delete Video

, or

Delete Audio

save attachments

View the message.

Highlight the attachment you want to save.

Press / >

Save Attachment

Selected items save to the default storage location.

delete attachments

View the message.

Highlight the attachment you want to delete.

essentials

Press / >

Delete Attachment

Press K under

Yes

to confirm.

outbox

The Outbox holds all unsent messages.

Find it:

Press / > E >

Outbox

resending failed messages from the outbox

Scroll to the message you want to resend or press the number of the message you want to resend.

Press K under

Resend

cancel an unsent message

Highlight the message you want to cancel.

Press /.

Press K under

Cancel

sent items

The Sent Items box holds sent messages.

forward items from sent items

Scroll to the message you want to forward.

Press / >

Forward

Make edits if you wish, select the recipient and press

under

Send

check delivery status

If a message was successfully sent and you set the message to confirm delivery, you can check the delivery status:

Scroll to the message you want to view.

Press / >

Delivery Status

essentials

delete sent messages

Scroll to the message you want to delete.

Press K under

Delete

Press K under

Yes

to confirm.

delete all unlocked sent messages

Press / >

Delete All

Press K under

Yes to confirm.

customize messaging

Find it: / > E > / >

Setup

This option is available from many context-sensitive menus.

The following options become available:

option

Signature:

Allows you to create a signature that is automatically inserted at the end of your messages. Signatures can be edited before sending the message.

Quick Notes:

Lets you create new Quick Notes

and edit or delete Quick Notes you created.

Cleanup:

Controls how long messages remain

in the

Inbox

and

Sent Items

before being

deleted.

Delivery Rpt:

Allows you to be automatically

notified when your message is delivered.

Memory Size:

Shows a report on used and free

memory in your phone.

MMS Setup:

opens a submenu to set MMS

options.

Text Msg Setup:

opens a submenu to set text

messaging options.

essentials

manage memory

Your text Inbox and Sent Items hold 200 messages each. The Outbox, and Drafts folder hold up to 30 messages each. If they are full, you cannot receive messages, send messages, or save drafts until you delete some items.

To view the amount of memory available in your text inbox:

Find it:

Press / > E > / >

Setup >

Memory Size

mms setup

Find it: / > E > / >

Setup

MMS Setup

This option is available from many context-sensitive menus when you are using MMS.

The following options become available:

text message setup

Find it: / > E > / >

Setup

Text Msg setup

option

Friendly Name:

Allows you to create a friendly

name. Your friendly name is displayed in the

From

field on other iDEN handsets when

your message is received.

Downloads:

Controls whether your phone downloads new messages. Set this option to

Automatic

if you want your phone to download new messages automatically. Select

Manual

if you want your phone to prompt you before downloading new messages.

Replies:

Lets you create or edit and delete

reply phrases you created.

essentials

This option is available from many context-sensitive menus when you are using MOSMS.

The following options become available:

new quick notes and reply phrases

create quick notes or replies

From the Setup menu, select

Quick Notes

, or

select

MMS Setup

Replies

Select

[New Quicknote]

, or

[New Reply]

Enter text from the keypad and press r.

edit quick notes or replies

You can edit only Quick Note phrases you have created.

From the Setup menu, select

Quick Notes

, or

select

MMS Setup

Replies

Select the quick note or reply you want to edit.

Edit the text and press r.

delete quick notes or replies you have created

From the Setup menu, select

Quick Notes

, or

select

MMS Setup

Replies

Scroll to the quick note you want to delete.

Press K under

Delete

Press K under

Yes

to confirm.

option

Srvc Cntr No:

Allows you to enter a service

center number.

Expire After:

Allows you to set the number of

days before a message expires.

essentials

delete all quick notes or replies you have created

From the Setup menu, select

Quick Notes

, or

select

MMS Setup

Replies

Press / >

Delete All

Press K under

Yes

to confirm.

cleanup options

The cleanup option controls how long messages remain in the Inbox and Sent Items before they are deleted. You set the cleanup option for the Inbox and Sent Items separately.

The clean up option deletes only read, unlocked messages and sent messages.

Find it: / > E > / >

Setup

Cleanup.

Select

Inbox

Sent Items

Choose a clean up option from the following list:

option

Off:

Messages are never automatically

deleted.

5 Messages:

If you have more than 5 messages, messages are deleted in the order they were received, starting with the oldest, until 5 are left.

10 Messages:

If you have more than 10 messages, messages are deleted in the order they were received, starting with the oldest, until 10 are left.

1 Day:

Messages are deleted if they are older

than 1 day.

3 Days:

Messages are deleted if they are

older than 3 days.

With these options, messages are deleted when you exit the message center after setting the option.

essentials

Press K under

Yes

to automatically

delete messages now or press

under

to delete messages later.

delete all messages

To delete all read, unlocked messages from the Inbox, all messages in the Drafts folder, or all successfully sent messages in the Outbox:

Find it: / > E.

Select

Inbox, Drafts, Sent Items

, or

Outbox

Press / >

Delete All

Press K under

Yes

to confirm.

delete a thread

To delete a thread from the Inbox:

From the Inbox, select a thread.

Press / >

Delete Thread

Press K under

Yes

to confirm.

message notifications

When you receive a message, your phone notifies you with text on the display, a notification tone or vibration.

You can access the message or dismiss the notification.

If you dismiss the notification, the message is not deleted. It can be accessed through the message center.

If you are not on a phone call when you receive a message, your phone sounds a notification tone every 30 seconds until you access the message or dismiss the alert.

F-In F-Out:

Messages are deleted as

necessary on an FirstIn FirstOut basis.

Custom:

Lets you create a clean-up option of

up to 199 days for the inbox.

option

essentials

If you are on a call when you receive a message, your phone may sound a notification tone during the call or after you end the call, depending on how you set your notification options.

set notification options

To control whether your phone sounds message notification tones while you are on a phone call:

Find it: / > u >

Phone Calls > Notifications

Select from the following options:

To set notification options during a call press

Call Setup

Notifications

using your handset as a modem

Your phone can be connected to a computer via USB for use as a modem. For more specific information on how to setup your phone for use with your computer please visit

www.motorola.com/support

and look under the FAQ

section.

option

Receive All

: Tones sound during calls for all

types of messages.

Msg Mail Only

: Tones sound during calls for mail messages; tones for all other types of messages are held until you end calls.

Delay All

: Tones for all types of messages are

held until you end calls.

Note:

Delay All

is the default setting.

option

basics

See page 1 for a basic phone diagram.

display

The home screen shows when you turn on the phone. To dial a number from the home screen, press number keys and

Note:

Your home screen may look different.

10:05pm 10/23

Ready

Time

Right Soft Key Label

Left Soft

Key Label

Date

Soft key labels show the current soft key functions. For soft key locations, see page 1.

status indicators

Status indicators are shown at the top of the home screen:

1Signal Strength Indicator:

Vertical bars show the strength of the network connection. You can’t make or receive calls when

shows.

10:05pm 10/23

1. 2. 3. 4.

5. 6. 7.

Ready

Time

Right Soft Key Label

Left Soft

Key Label

Date

basics

2Active Phone Line: $ indicates phone

line 1 is ready to make calls;

(

indicates

phone line 2 is ready to make calls.

3Speaker On/Off:

Sounds associated with Private calls and group calls can be set to come through the earpiece rather than through the speaker.

4 Ringer Vibe/Off:

Your phone is set to not ring.

5 Message Indicator:

Shows when

you receive a text message.

6 Packet Data:

Your handset is ready to transfer packet data or is transferring packet data when it shows a blinking arrow.

7 Battery Charge Indicator:

A fuller battery indicates a greater charge. Recharge the battery when your phone shows

Low Battery

main menu

All your phone’s features can be accessed through the main menu. You can set the main menu to appear as

List View

Icon View

Find it: / > u >

Display/Info

Menu View

text entry

Some features let you enter text.

Your phone provides convenient ways to enter words, letters, punctuation, and numbers whenever you are prompted to enter text (for example, when adding a Contacts entry or when using Text Messaging).

change the character input mode

When you see a screen where you can enter text, press

to change the

character input mode.

basics

Select one of the following options:

word method

The Word text input method predicts the word you are typing by comparing the letters entered with dictionaries of words, and provides the most commonly-used word as you type. You may use up to two dictionaries, one for a primary language and another for a secondary language.

enter a word using “word” method character input

Select the

Word

character input method.

Press the corresponding keys to enter a word (for example, to enter the word

Bill

press

F G H H

). (If you make a

mistake, press

to erase a single

character. Press and hold

to delete an

entire entry.)

To accept a word and insert a space, press

entry method

Alpha

Press a key several times for different characters.

Word

Enter words using a predictive text entering system that lets you enter a word with fewer keypresses.

Text Settings

Selects the desired entry languages and Word Prediction features.

Insert

Selects a item to be inserted, such a picture, an audio/video clip or a voice recording.

Note:

available only when composing a message using MMS.

basics

To accept a word completion (such as

Billion

when you entered

Bill

), press the

navigation key to the right. To enter

Bill

press the navigation key to the left.

If next word prediction is turned on, when you hit space, you will be presented with a predicted word option. For example, if you enter

, you will be presented with a

predicted word option such as

. Press the navigation key right to accept the predicted word.

If two or more word combinations result from the sequence of letters entered, a down arrow will be displayed. Press and hold the navigation key down to display a list of possible word choices.

When word completion is turned on, if you get a word you don’t want, you can press the navigation key up or down to see more word choices.

alpha method

To enter characters by tapping the keypad:

Select the

Alpha

method.

Press the corresponding keys to enter a word. For example, to enter the word

Bill

press

F G H H

. If you make a

mistake, press

to erase a single

character. Press and hold

to erase an

entire word.

To enter a symbol character, press B or A and the key for the symbol you wish to enter.

By default, the first letter of an entry is capitalized.

basics

volume

Press the volume keys up or down to:

•

turn off an incoming call alert

•

change the earpiece volume during calls

•

change the ringer volume from the home screen

Tip:

You can quickly set your ringer to

Vibrate All

by holding the down volume

key in the home screen.

navigation key

Press the navigation key up, down, left, or right to scroll to items in the display. When you highlight the desired item, press

to select

it.

handsfree speaker

You can use your phone’s handsfree speaker to make calls without holding the phone to your ear.

During a call, press

under

Spkr

to turn the

handsfree speaker On.

The handsfree speaker stays on until you press

under

Spkr

again.

basics

transmitters

Consult airline staff about the use of the Transmitters Off feature during flight. Turn off your phone whenever instructed to do so by airline staff.

Transmitters Off turns off your phone’s calling and Bluetooth features in situations where wireless phone use is prohibited, but you can use the phone’s other non-calling features when Transmitters is turned Off.

Find it: / > u >

Advanced

Transmitters

Off

use GPS with map software

Your phone can be connected to a PC, laptop, or PDA via USB for use as a GPS receiver. For more specific information on how to setup your phone for use with your computer please

visit

www.motorola.com/support

and look under the

FAQ sect io n.

features for the hearing impaired

using your phone with a hearing aid

For best results use the following optimization procedures and handset setting. They generally apply as well for users with cochlear implants:

optimize your handset position and orientation

While in a phone call slide your phone up and down, then left and right until best microphone coupling is obtained. You also may need to adjust your hearing aid (HA) volume setting

Approximate telecoil location is just above the battery.

Approximate telecoil location is within 6-13 mm of this location.

Off - Shut off M - Microphone T - Telecoil

basics

If your HA has a telecoil, activate its switch, then also rotate the handset as illustrated to align the telecoils.

Note:

Some automatically switched hearing

aids may need an auxiliary switching magnet.

If you are unsure whether your HA is telecoil equ

ipped or needs an auxiliary magnet, please refer to your HA user guide or contact a hearing aid professional or supplier.

choose your hearing aid setting

Find it: / > u >

Phone Calls

Hearing Aid

Set this option to Microphone

. Microphone

coupling is now optimized.

Set this option to Telecoil

. Handset meets US federal requirements for telecoil coupling sound or set this option to

Off

(factory default). This is the setting for non HA users.

basics

TTY security features

Shortcut:

To l ock t h e

keypad press

> *.

Note:

You can make emergency calls on a

locked phone (see page 64).

feature turn On TTY

feature

Press / > u >

Phone Calls

TTY

Use TTY

> On.

choose TTY mode

Press / > u >

Phone Calls

TTY

Type

Select from

TTY, VCO

HCO

change the TTY baud rate

Press / > u >

Phone Calls

TTY

Baud

Select

45.45

50.00

change TTY mode during a call

While in the TTY call, press

In Call Setup

TTY

Type

Select from

TTY, VCO

HCO

feature phone lock

To lock the phone press

Security

Phone Lock

Lock Now

Auto Lock

keypad lock

To lock the keypad press

> u > Security

Keypad Lock

Lock Now

Auto Lock

enable SIM PIN

Press / >

Security

SIM PIN

> On.

change SIM PIN

Press / >

Security

Change Passwords

SIM PIN

main attractions

media center

The media center lets you access pictures, audio recordings, and videos stored in your phone’s memory.

The following audio recordings can be accessed through the media center:

•

Voice records

•

Musical ring tones in the list of ring tones

•

Audio recordings saved from MMS messages received

•

Audio recordings downloaded to your phone

Items in the media center can be sent in MMS messages and with Bluetooth. See “mms features” on page 21 and “Bluetooth®” on page 57.

Pictures in the media center can be sent in Private calls using Send via PTT. See “PTX features” on page 49.

Audio files supported by the Media Center include:

Format Sampling Rates/Bit Rates

.au 8 KHz/8 kbps

.midi

8 KHz

.mp3 8 KHz/8 kbps

.wav 8 KHz/64 kbps

.amr 12kbps

main attractions

Image files supported by the Media Center include:

Video files supported by the Media Center include:

video player

From the Media Center, scroll left or right to Media: Video.

Select the video you wish to view, and it will begin to play.

To stop the video, press the navigation key down. To play the video again, press r.

camera

You can save pictures taken with the integrated camera in your phone’s memory, and can access them through the Media Center.

Pictures you take can be sent via Private Calls, Bluetooth, or MMS message. You can also set them as your phone’s wallpaper.

Format Max. Image Size (i n pixels)

.png

128 x 160

.gif

128 x 160

.jpg

640 x 480

.wbmp

128 x 160

Format Frame Rate and

Max. Image Size (in pixels)

AVI

15fps 128 x 96

H.263

15fps 128 x 96

MPEG

15fps 128 x 96

main attractions

access the camera

To access the camera, press e.

To take pictures aim the camera lens and press

under

Capture

or press r.

To save the picture, press

To discard the picture without saving it, press

under

Discard

From the camera viewfinder, you can press

to enter

Menu Options

The following options become available:

option

Media Center

: Opens the Media Center

application.

Record Video

: To record a video

Zoom

: To set the camera’s zoom to 1x, 2x, or

4x.

Lighting

: Turn on the spotlight On before taking a picture in low light conditions. You can set it up to be

Normal

Low Light

Self Timer

: Delay capturing the picture for a selected number of seconds. The values are:

Off

(default),

10 seconds, 15 seconds

, and

seconds

To turn off the timer before the picture is captured, press

under

Cancel

Picture Quality

: Adjust the picture quality to

Normal

Fine

Picture Size

: Set up the picture size to

(640x480)

L (320x240), M (160x120), S (128x96)

, or

WP (128x160)

. You can also set picture size from the viewfinder by pressing left and right.

Memory Usage

: Shows the total amount of

Used,

Free

, and total

Capacity

of the phone’s

memory.

option

main attractions

access the media center

You can access the media center from the camera at any time by pressing

Media

Center

, except when you are using the

Camera

Setup

menu or viewing the memory screen.

The media center contains all your pictures, music files, and videos located on your phone’s memory. Press

and * or A and

to filter your results.

customize the camera

Find it: e > / >

Camera Setup

The following options become available:

Camera Setup

: To access the camera set up

screen.

option

Ask for Name

: If this option is On, you are prompted to enter a name for each picture before saving. Otherwise, pictures are automatically saved with the date and a number as their names.

Shutter Sound: Sets the default sound the

camera makes when it takes a picture.

Default Size: Sets the default value for the

Picture

Size

option.

Default Quality

: Sets the default value for the

quality of the picture.

main attractions

PTX features

With Push To View features, your phone can send and receive the following items through Private calls with other phones that have this capability:

•

Short text messages

•

Pictures

•

Datebook events

•

My Info

•

Contact information

•

Location information

You can choose to send messages, pictures, events,

My Info, Contacts

Location

information to the Private ID you are engaged in a Private call with, Private IDs on the

Recent Calls

list, and

Private IDs stored in

Contacts

When you make or receive a Private call, your phone automatically determines whether the phone you are engaged in a Private call with is able to receive each of these items. Your phone saves this information for as long as the Private ID is on your

Recent Calls

list or is

saved in your

Contacts

. Your phone updates the saved information each time you make or receive a call to or from that Private ID.

Note:

You cannot send PTT feature items

during Talkgroup calls.

send messages

The Push to Send Messages feature lets you send short text messages through Private calls.

When you send a message, it appears on the display of the phone you are engaged in the Private call with.

1. Additional charges may apply.

main attractions

begin a message and choose a recipient

You can begin a message during a Private call, from the

Contacts

list, the

Recent Calls

list, or from

the

PT Manager

begin a message during a Private call

While in a Private call, press / >

Use PTT Feature

Send Message

Note:

The first time you send a message,

Messaging Fees May Apply Continue?

appears and you

are prompted to respond. Press

under

Yes

to acknowledge the message.

begin a message from the Contacts or the Recent Calls list

From the

Contacts

or the

Recent Calls

list, select the entry containing the Private ID you want to send the message to.

Press / >

Use PTT Feature

Send Message

begin a message from the PT Manager

The

PT Manager

lets you select the Private ID

you want to send the message to from

Contacts

or the

Recent Calls

list.

Find it: / > N >

Send Contact > Browse.

Then select

Contacts

Recent Calls

to see a list of

entries from the

Contacts

or the

Recent Calls

list

that can receive messages.

create messages

After you have begun a message and chosen a recipient, a screen appears that lets you create the text of the message you want to send. Your message may be up to 400 characters long.

You can choose from a list of ready-made words or short phrases called Quick Notes. You can use a Quick Note as it is or edit it before you send it. Editing a Quick Note

main attractions

changes the Quick Note for this message only and will not change the Quick Note on the list.

send a completed message

After you have completed your message, press the PTT button to send it.

receive messages

When you receive a message, a message notification appears on the display.

To view the message: Press

under

Read

To dismiss the message press

under

Dismiss

reply to a message

View the message.

Press K under

Create the message and press the PTT button to send it.

send pictures

You can send pictures stored in the

Media

Center

through Private calls. The picture you send appears on the Private call recipient’s display.

If the recipient accepts the picture, their phone saves the picture. The picture then appears in that phone’s recent call list.

The first time you send a stored picture after turning the phone on,

Picture Fees May Apply

Continue?

appears and you are prompted to

respond.

Note:

You cannot make or receive Private

calls while transmitting or receiving a picture.

send a picture during a call

While in a Private call, press K under

Picture

or press / >

Use PTT Feature

Send Picture.

main attractions

A list of pictures that can be included in a Private call appears.

Select the picture you want to send.

Press the PTT button to send the picture.

Wait while the picture is transmitted. The Private call is temporarily interrupted while a picture is transmitted.

When prompted, press the PTT button to resume the Private call.

start a call by sending a picture

from the media center

Find it: / >

Media Center

Scroll left or right to

Media: Pictures

Select the picture you want to send.

Press

/ > Send Via...

Send Via PTT

Select

A Contact

A Recent Call

A list of contacts that have Private IDs and are able to receive pictures appears.

Select the name of the person you want to send the picture to.

Press the PTT button to send the picture.

When prompted, press the PTT button to resume the Private call.

from the PT Manager:

Find it: / > N >

Send Picture

Select

A Contact

A Recent Call

A list of contacts that have Private IDs and are able to receive pictures appears.

Select the name of the person you want to send the picture to.

Select

Browse Picture

Capture Picture

Press the PTT button to send the picture.

main attractions

Once picture has been sent, when prompted press the PTT button to resume the call.

receive a picture

When someone sends you a picture, your phone emits a tone or vibrates and a message appears asking if you want to accept the picture.

Pictures you receive are saved to your phone’s memory. They are accessible through the media center.

When you see a message asking if you want to accept the picture, press

Yes

to accept or No

to decline.

clear a picture from the display

If you want to clear a picture from your phone’s display while still on a call, press

Clear Screen

send a datebook event

to send a datebook event during a private call

While in a Private call press / >

Use PTT Feature

Send Event

Note:

If these options do not appear on the menu, the Private ID you are engaged in a private call with is not able to receive Datebook events.

If you want to create a new datebook event, press

under

New and create the

event in your datebook. If you want to chose an existing event do so.

If the event is a recurring event: Select

This Event Only to send only the event

selected. Select

Repeat Events

to send all

occurrences of the event.

Push the PTT button to send the event.

main attractions

send my info

While in a Private Call press / >

Send via PTT > Send My Info

, and push the PTT

button to send.

From the home screen press / >

My Info

> / >

Send via PTT

. Enter a Private ID

or press

under

Browse

to chose a recipient from Contacts, Recent Calls or Memo, and press

. Push the PTT

button to send.

set my info sending option

You can control what portion of the information in

My Info

is sent and whether it is sent automatically in every call or only when you choose to send it.

Find it: / >

PT Manager

Configure

PTT My Info

Info to Send

Select or remove the fields you want to send.

Press K under

Done

The information your phone sends always in

cludes

My Name

, and

Private

. You may also

send

Line 1,

Line 2

, and

Carrier IP

, depending on

your sending options.

automatic sending

To control whether you send your information automatically:

Find it: / >

PT Manager

Configure

PTT My Info

Auto Send

Select On or

Off

When you make a call in which your information is sent automatically, the name you entered in the

My Name

field of

My Info

appears on the display of the

recipient’s phone, even if your name and

main attractions

Private ID are not stored in the recipient’s Contacts.

send contact information

While in a Private Call press / >

Use PTT Feature

Select

Send Contact

and select the contact

information you want to send.

Push the PTT button to send.

From the home screen press / >

PT Manager

Send Contact.

Enter the Private ID number of the person you want to send the Contact information to or press

under

Browse

Select from

Recent Calls, Contacts

, or

Memo

Select the contact information you want to send and push the PTT button.

turn PTT features on and off

You can turn your phone’s ability to send and receive messages, pictures, and Datebook events on and off.

Find it: / > u >

2-Way Radio> On/Off PTT

Check or uncheck Messages, Pictures or Events.

You cannot turn your phone’s ability to send and receive My Info and contact information on and off.

main attractions

one touch PTT

Find it: / > u >

2-Way Radio

One Touch PTT.

One Touch PTT sets your phone to do any of the following each time you press the PTT button from the home screen:

quick PTT

Quick PTT lets you quickly make a call, when accessing any Private IDs on your phone.

option

Off

: Nothing happens when you press the

PTT button from the home screen.

Quick PTT

: Go to Quick PTT. See “quick PTT”

on page 56.

Last Call

: Call the most recent Private ID or

Group on the recent calls list.

Assigned No.

: Call a Private ID you assign. Enter the number using your keypad, or press

under

. Select

Contacts, Recent

Calls

, or

Memo

Note:

If you are entering a Talkgroup

number, enter

before the number.

PT Manager

: Go to PT Manager. See “PT

manager” on page 57.

Send Message

: Go to the first screen to send a

message.

Send Picture

: Go to the first screen to send

pictures. See “send pictures” on page 51.

Send Event

: Go to the first screen to send a

Datebook event.

Send My Info

: Go to the first screen to send My

Info. See “send my info” on page 54.

Send Contact

: Go to the first screen to send a contact. See “send contact information” on page 55.

option

main attractions

To view a list of Contacts with Private IDs in

Contacts

Find it: / >

Quick PTT

To move between

Contacts, Recent Calls

, or

Memo

use the

;

left or right, or press A and * or

and #.

To make a Private call:

Select the entry you want.

Press K under

Done

Push the PTT button.

PT manager

The

PT Manager

lets you quickly access PTT features, and other Private call features, from the main menu.

Find it: / >

PT Manager

Select

Quick PTT, Send Message, Send Picture, Send

Event

Send My Info, Send Contact,

Configure

After choosing what PTT item you are sending, select a contact and press the PTT button to send.

Select Configure

to configure your

PTT Quick

Notes

PTT My Info, One Touch PTT

, or

On/Off PTT

Bluetooth®

Find it: / >

turn Bluetooth on or off

You can turn your phone’s Bluetooth feature on or off. While Bluetooth power is on, your phone can communicate with other devices.

Find it: / > c >

Setup > Power

Select On to power Bluetooth On.

Select

Name

if you wish to assign a name

to your handset.

main attractions

Select

Find Me Time

to determine the amount of time in which your handset can be found by other Bluetooth devices.

You can turn off Bluetooth if you want to prolong battery life or if you enter an area where Bluetooth is prohibited.

make a Bluetooth connection

connect your handset with a Bluetooth headset

Find it: / > c >

Hands Free> [Find Devices]

Follow the instructions on your Bluetooth headset to set it up to be found.

Once your Bluetooth headset is set to be found press

on your handset. Your phone will scan for the Bluetooth headset until it finds it. Press

when you see the name of the Bluetooth headset on your screen.

Your handset requires that you create a bond in order to connect with a Bluetooth headset. Press

under

Yes

when you

are prompted to bond with the headset.

Enter the Bluetooth pass key.

Some Bluetooth devices ship with Bluetooth PINs. Please refer to your Bluetooth device’s user guide to locate this information.

If a device ships without a Bluetooth PIN, then you can enter any PIN for that device. To establish a connection to that device, enter the same PIN for both your phone and the device. For example, if you enter 1234 as the device’s PIN, then enter 1234 as your phone’s PIN.

Press K under Ok.

This handset offers the Bluetooth auto pair feature with auto pair compatible Motorola

main attractions

devices. When bonded via Bluetooth with a certain device, the pin will not be required.

connect your handset with another Bluetooth device

Find it: / > c >

Link To Devices

Select the device you want from the list of found devices on your screen.

Create a bond if you are prompted to do so.

If you have previously connected to a device, the de

vice will be stored on your phone so

you can connect with it easily.

use Bluetooth during a call

You can connect with available Bluetooth devices during a call.

While in a call, press / >

Use Bluetooth

Select the audio device you want to connect to from the list of

Hands Free Devices

If the

Audio Devices

list contains only one device,

your phone will try to connect to it.

send information via Bluetooth

Your handset can transfer Contacts entries, Datebook events, audio files, pictures and videos to another Bluetooth device.

The receiving device must be within 32 feet (10 meters) of your phone in order to connect.

Note:

Files sent or received may be up to 1 MB, depending on your service pr

ovider.

sending information

From within Contacts, datebook, or Media Center, select the Contacts entry, Datebook event, audio file, video, or picture you want to send.

Press / >

Send Via...

Bluetooth

main attractions

Select the device you want to transfer the contact information to, or search for the device by selecting

[Find Devices]

If prompted, bond with the device.

Your phone connects with the devices and transfers the information.

call features

turn off a call alert

You can press the volume keys to turn off a call alert before answering the call.

recent calls

The recent calls list contains information associated with calls you have made and received and call alerts you have received.

When you send or receive Private calls, the recent call list contains the following PTX items with those calls:

•

contact information received

•

My Info received

•

short text messages received

•

pictures sent or received

•

Datebook events received

The recent calls list displays up to 20 of the most recent calls and call alerts.

Press / >

Recent Calls

Scroll through the list.

To view more details of the item press r.

store an item to contacts from recent calls

Phone calls, Private calls, My Info, Contacts or Location entries received from other phones can be stored to the Contacts list from the Recent Calls list.

call features

Find it: / >

Recent Calls

Scroll to or select the item you want to store.

Press K under

Save

to store the information as a new entry in the Contacts list.

Select an existing contact and update the information.

Press K under

Done

to save your changes.

redial

To redial your last outgoing call, press and hold

or push the PTT button if it was a

private call.

caller ID

Caller ID allows people to identify a caller before answering the phone by displaying the number of the incoming call. If you do not want your number displayed when you make a call, just follow these easy steps.

To block your phone number from being displayed for a specific outgoing call:

Press

* 6 7

Enter the number you want to call.

Press

To permanently block your number, call your customer service provider.

call forward

Call forwarding sends calls to the phone numbers you specify. You can forward all calls to one number or forward missed calls to

call features

different numbers depending on the reason you missed the call. You can forward phone lines 1 and 2 independently.

Find it: / >

Call Forward

To forward all calls select

All Calls

and select

to enter the phone number you want all

your calls forwarded to.

You can specify a forwarding number for each type of missed call by selecting

Detailed

and choosing the following options:

If Busy

: When your handset is on a call or

transferring data.

If No Answer

: When you do not answer on

the first 4 rings.

If Unreachable

: When your handset is out of

coverage or powered off.

voice names

You can place calls by speaking commands to your phone if you have previously assigned a voice name to your contacts.

assign voice names to contacts

Press K under

Contcs

and select

[New Contact]

Assign a name, phone number and select

[Options]

Select

Voice Name

and follow the prompt to

record the voice name.

Press K under

Back

and K under

Save

place a call using a voice name

Press the speaker key ) until you are prompted to say the voice name.

The handset will automatically place the call.

call features

emergency calls

Your service provider programs one or more emergency phone numbers that you can call under any circumstances. Emergency calls can be made without a SIM card, when your phone is locked, or when the SIM card is blocked.

Note:

Emergency numbers vary by country. Your phone’s preprogrammed emergency number(s) may not work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues.

Dial 911 or your local emergency number to b

e connected to an emergency response center. If you are on an active call, you must end it before making an emergency call.

When you make an emergency call, your phone’s GPS Enabled feature can help emergency service personnel find you, if you

are in a location where your phone's GPS antenna has established a clear view of the open sky and your local emergency response center has the equipment to process location information. Because of the limitations of this feature, always provide your location, to the best of your knowledge, to the emergency response center when you make an emergency call

Note:

Emergency calls cannot be placed while the keypad is locked, or if your phone is displaying a

No Service

message on the screen.

To unlock the keypad, press

international calls

If your phone service includes international dialing, press and hold

to insert your local international access code (indicated by +). Then, press the keypad keys to dial the country code and phone number.

call features

speed dial

Each phone number stored in Contacts is assigned a Speed Dial number, which you can use to call that number.

From the home screen, use the keypad to enter the Speed Dial number assigned to the phone number you want to call.

Press #.

Press ,.

turbo dial

The first nine entries in your contacts are set for turbo dial. They can be called by pressing and holding the speed dial number (1 through 9).

voicemail

To receive voice mail messages, you must first set up a voice mail account with TELUS.

receiving a message

When you receive a voice mail message,

New

VoiceMail Message

appears on the display.

To call your service provider’s voice mail system and listen to the message:

Press K under

Call

To dismiss the message notification:

•

Press r or

Back

If the caller leaves a message, this icon

appears on the display, reminding you that you have a new message.

call features

advanced voice mail with fax

Mike's Advanced Voice Mail with Fax allows you to receive faxes directly to your handset and store them along with your voice messages until you are ready to print. Follow the voice mail prompts to print the fax to a fax machine. It ensures privacy, convenience and eliminates the need for a separate fax line.

When you subscribe to Mike's Advanced Voice Mail with Fax, you will receive a fax number from your point of feature activation. If you have not received a fax number, please contact the nearest TELUS dealer or call TELUS client care.

Please see

www.telusmobility.com

for more details of TELUS Voice Messaging services.

fax mail Indicator

Your handset is equipped with a Fax Mail indicator to notify you when you have received a fax through Mike's Advanced Voice Mail with Fax.

Shortcut:

From the home screen press -

under

Mesg

Fax Mail

When you receive a new fax, New FaxMail Message appears on the display.

Your handset will alert you audibly until you press

under

Call

or - under

Exit

net alerts

When you receive a

Net Alert

, a notification

appears on the display.

If you dismiss the notification, this icon

appears on the display, reminding you that you have a new message.

Mike’s Talk Around TM

Mike’s Talk Around

Note:

This feature may not be offered by your

service provider.

With Mike’s Talk Around, you can make and receive Two-Way Radio calls without network coverage. If you are travelling outside your service provider's coverage area, receiving a poor signal, or otherwise want to temporarily avoid using your service provider's network, you can switch to Mike’s Talk Around and talk with anyone on your code and channel who is within range.

Note:

Range will vary based on terrain, man-made structures and atmospheric conditions.

Mike’s Talk Around lets you:

•

Use code or private mode operation

•

Use up to 10 channels

•

Communicate with standalone Mike’s Talk Around radios

Note:

You cannot use Mike’s Talk Around

with older Family Radio Services products.

The following features and main menu items are unavailable while in Mike’s Talk Around:

•

On-network phone or Private calls

•

Data transmission

•

Incoming message notification

•

Datebook

•

Call forwarding

•

Call Timers

•

Call alerts

Mike’s Talk Around TM

switching to Mike’s Talk Around

To set your phone to Mike’s Talk Around:

From the home screen press / >

Talk Around and press r.

Select

Go to Talk Around

Switching to Talk Around Please Wait

displays.

After a few seconds, the Talk Around idle screen displays. When

TA Ready

displays,

you can begin using Mike’s Talk Around.

While in Mike’s Talk Around, this icon 4 displays.

exiting Mike’s Talk Around

To switch to network mode:

From the Talk Around idle screen, press

TA Options

and press r.

Select

Exit Talk Around

Switching to Network Please Wait

displays. After a few

seconds, the network idle screen appears.

talk range

While in Mike’s Talk Around mode, phones should be a minimum of 6 feet apart to maximize performance and improve transmission range.

channels and codes

Your phone has 10 channels and 15 codes. Channels are divided into sets of frequencies. Other parties may be talking on the same channel. Codes minimize interference from other parties when you are sharing the same channel.

Mike’s Talk Around TM

Mike’s Talk Around opens to the last code and channel used on your phone. You can view the code and channel your phone is currently set to on the Talk Around idle screen.

For code calls, all parties must be on the same channel and code. For private Mike’s Talk Around calls, the person you are calling must be in Mike’s Talk Around and set to the same channel to receive your call.

Note:

When making a code call, all parties that are on your code and channel can hear your conversation.

setting channels and codes

To set a channel:

From the Talk Around idle screen, press

under

Edit

Scroll to

Channel

Press K under

Edit

Select a channel.

When you are finished, press K under

Back

to return to the Mike’s Talk Around

idle screen.

To set a code:

From the Talk Around idle screen, press

under

Edit

Scroll to

Code

Press K under

Edit

Select a code.

When you are finished, press K under

Back

to return to the Talk Around idle

screen.

making code calls

To make a code call:

From the Talk Around idle screen or the channel and code edit screen, press and

Mike’s Talk Around TM

hold the PTT button.

Transmit

appears on the first line of display. Begin speaking after your phone emits the Mike’s Talk Around tone.

Note:

The Mike’s Talk Around tone consists of

4 rapid beeps.

Release the PTT button to listen.

If you receive an error message:

•

No one is on your channel or code.

•

You are out of range.

receiving code calls

When you receive a code call,

Receive

will appear on the display. After hearing the Mike’s Talk Around tone, you have 6 seconds to reply before the call times out.

To reply to the call, press the PTT button.

Note:

An incoming Mike’s Talk Around call

can be terminated at any time by pressing

receiving all Mike’s Talk Around calls

If you set the code to

Receive All

, your phone can receive Mike’s Talk Around transmissions from any phone that is set to the same channel, regardless of the code (1-15). When you receive transmissions with the code set to

Receive All

, the code that the transmission

was received on will replace

Receive All

on the

display.

Note:

You cannot initiate a code call when the

code is set to

Receive All

To set the code to

Receive All

From the Mike’s Talk Around idle screen, press

under

Edit

Scroll to

Code

Mike’s Talk Around TM

Press K under

Edit

Select

Receive All

When you are finished, press K under

Back

to return to the Mike’s Talk Around

idle screen.

To reply to a call with the code set to

Receive All

•

Press the PTT button.

private Mike’s Talk Around calls

If you want to have a private conversation without other parties listening in, you can make a private Mike’s Talk Around call. The person you are calling must be in Mike’s Talk Around and set to the same channel to receive your call.

private only

To set Mike’s Talk Around to ignore code calls, so that you only make or receive private Mike’s Talk Around calls, set your code to

Pvt Only

To set the code to

Pvt Only

From the Talk Around idle screen, press

under

Edit

Scroll to

Code

Press K under

Edit

Select

Pvt Only

When you are finished, press K under

Back

to return to the Talk Around idle

screen.

Mike’s Talk Around TM

making a private Mike’s Talk Around call

Enter the PTN of the person you want to call on your channel. If the PTN is more than 10-digits, enter the last 10-digits of the PTN, or scroll to a number or name in Contacts or the Recent Calls List.

Press and hold the PTT button. Begin speaking after your phone emits the Mike’s Talk Around tone.

Release the PTT button to listen.

The number or name of the person you are calling will appear in the display.

If you receive an error message:

•

The PTN you entered is invalid.

•

The person that you are trying to reach is in network mode.

•

The person that you are trying to reach is set to a different channel.

•

The person that you are trying to reach is out of range.

receiving a private Mike’s Talk Around call

The number or name of the person who is calling will appear in the display.

To reply, press the PTT button.

ending code calls and private Mike’s Talk Around calls

Code calls and private Mike’s Talk Around calls will end automatically after 6 seconds of inactivity.

The Talk Around idle screen will display.

Mike’s Talk Around TM

Note:

A private or code Mike’s Talk Around call can be interrupted during the 6 second idle time by another code call or private call.

making emergency calls while in Mike’s Talk Around

mode

If you attempt to make an Emergency 911 call while in Talk Around mode, your phone will automatically exit Talk Around mode and attempt to find a network signal.

If you are out of network coverage your phone will not be able to make an emergency 911 cellular call until you go back into the network coverage area.

You must wait until the phone reconnects to the network before attempting to make an emergency 911 cellular call.

setup options

You can set up Mike’s Talk Around options on the TA Options screen. You can access this screen in both network and Talk Around modes.

To access setup options:

Press

/ > Talk Around or TA Options.

Select

Setup

You can set the following Mike’s Talk Around options:

•

Direct Launch

: Launch directly into Mike’s

Talk Around when you select

Talk Around

from the main menu.

•

State Tone

: Have an alert sound notify you that you have used Mike’s Talk Around for a specified interval.

Mike’s Talk Around TM

using direct launch

To set your phone to launch Mike’s Talk Around when you select

Talk Around from the

main menu:

From the Setup screen, scroll to

Direct

Launch

and press r.

Select On.

Note:

Direct Launch

is set to On, the Mike’s Talk Around setup options will be unavailable from the main menu. However, you can still access setup options while in Mike’s Talk Around by pressing

and selecting >

TA Options

Setup

To turn off Direct Launch:

From the Setup screen, scroll to

Direct

Launch

and press r.

Select

Off

TA Options

will now display when you select

Talk Around from the main menu.

using state tone

To set your phone to alert you after you have used Mike’s Talk Around for a specified interval:

From the Setup screen, scroll to

State Tone

and press

Select the interval after which you want the tone to sound.

For example, if you select 1 hour, you will be notified every hour that you are in Mike’s Talk Around.

To turn off State Tone:

From the Setup screen, scroll to

State Tone

and press

Select

Off

customize

ring tones

To set the ring tone your phone makes when you receive phone calls, call alerts, message notifications, pictures sent using Send via PTT or Datebook reminders:

Find it: / >

Ring Tones

Make sure

Vibrate All

is set to

Off

Scroll through the list of ring tones and select the one you want to assign.

Vibrate

sets your phone to vibrate instead

of making a sound.

Silent sets your phone

to neither vibrate nor make a sound.

Select the features you want to assign the ring tone to.

When you are finished, press K under

Done

Note:

This icon , appears on the display if

you set your phone to

Silent

. This icon 5

appears on the display if you set the phone to

Vibrate All

set your phone to vibrate

You can set your phone to vibrate instead of making a sound when you receive all phone calls, Private calls, Talkgroup calls, call alerts, message notifications, pictures sent using Send via PTT, and Datebook reminders.

Find it: / >

Ring Tones

Vibrate All

Set this option to On or

Locked

customize

Setting this option to On lets you turn

Vibrate All

off by pressing the up volume control. Setting this option to

Locked

requires you to press and

hold the up volume control to turn

Vibrate All

off.

The

Locked

option helps prevent you from

accidentally turning

Vibrate All

off.

To s et

Vibrate All

to On or

Locked using the volume

controls:

Press the volume controls to turn down the volume as far as possible to set

Vibrate All

to On. Continue to hold the down volume control to set

Vibrate All

Locked

To set your phone to vibrate instead of making a sound for some features but not others:

Find it: / >

Ring Tones

Make sure

Vibrate All

is set to

Off

Select

Vibrate from the list of ring tones.

Select the features you want to set to make no sound.

When you are finished, press K under

Done

backlight

Set the amount of time that the display and java apps. backlights remain on, or turn off the backlight feature to extend battery life.

Find it: / > u >

Display/Info

Backlight

LED indicators

You can turn off the Bluetooth, messaging, and voicemail indicators.

Find it: / > u >

Display/Info

Backlight

Bluetooth LED, Message LED

, or

VMail LED

Off

customize

wallpaper

Set a previously saved photo or picture as a wallpaper (background) image in your phone’s external display, internal screen or throughout all menu screens.

Find it: / > u >

Display/Info

Wallpaper

Select

Wallpaper

Scroll through the list of pictures and press

to select a picture.

You can set the wallpapers to change automatically after a certain period of time by turning on the

Auto Cycle

feature located in the

Wallpaper menu. You can select from

5 minutes

15 minutes, 1 hour, 8 hours, Daily

, or

Startup

datebook

feature create

datebook events

To create a new Datebook event press

Datebook

[New Event]

see datebook event

To see a calendar event press

Datebook

. Press ; left or right to see the day and

;

up or down to see

the events.

event reminder

When an event reminder occurs press

under

View

Press

under

Back

to close

the reminder.

customize

datebook setup

Find it: / >

Datebook > /

Setup

You can view or change these options:

receive datebook events via PTT

To view the information while still in the Private call press

The 5 most recent events received from a Private ID are stored with that Private ID on the recent calls list.

To store events to the Datebook press

under

Save

while viewing the event

you want to store.

feature

options

Start View:

Sets Datebook to start in day view, week view, or month view when you access Datebook.

Daily Begin:

Sets the beginning of your day. This is the earliest time of day displayed in week view, if you have a 12-hour day view.

Delete After:

Sets the amount of time Datebook waits to delete an event after it occurs.

Time Shift:

Lets you shift the times of all Datebook events. This is useful if you are traveling to a different time zone.

Alert Timeout:

Sets the amount of time a tone continues to sound when you receive a Datebook reminder.

customize

hide or show location information

Your phone is equipped with a Location feature for use in connection with locationbased services that may be available in the future.

Turning Location

will allow the network to detect your position using GPS technology, making some applications and services easier to use. Turning Location off will disable the GPS location function for all purposes except 911, but will not hide your general location based on the cell site serving your call. No application or service may use your location

without your request or permission. GPSenhanced 911 is not available in all areas.

set your privacy options

Find it: / >

GPS > Privacy

Select from the following options:

Clock:

Controls whether the time and date appear on the home screen; sets time and date format; sets year.

options

option

Restricted:

No Java or similar software applications may view the location of your phone. However, location information may still be available to the phone’s owner, fleet manager, or account administrator.

Unrestricted:

All applications may view the location of your phone, without notifying you.

customize

change GPS PIN

When you receive your phone, your GPS PIN is 0000.

To change your GPS PIN press

> u >

Security

Change Passwords

GPS PIN

. Enter the current GPS PIN and enter the new four to eight digit GPS PIN. Re-enter the new four- to eight-digit GPS PIN to confirm.

Ask Access:

When an application attempts to view the location of your phone, you will be prompted to give permission. However, location information may still be available to the phone’s owner, fleet manager, or account administrator.

option

Legal and Safety

Safety and General Information

This section contains important information on the safe and efficient operation of your mobile device. Read this information before using your integrated multi-service portable radio.*

Exposure to Radio Frequency (RF) Energy

Your mobile device contains a transmitter and receiver. When it is ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits.

Your mobile device is designed to comply with local regulatory requirements in your country concerning exposure of human beings to RF energy.

Portable Radio Product Operation and EME Exposure

Your Motorola radio product is designed to comply with the following national and international standards and guidelines regarding exposure of human beings to radio frequency electromagnetic energy (EME):

•

United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J.

•

American National Standards Institute (ANSI) / Institute of Electrical and Electronics Engineers (IEEE). C95. 1-1992.

•

Institute of Electrical and Electronics Engineers (IEEE). C95. 1-2005 Edition.

•

International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998.

•

Ministry of Health (Canada). Safety Code 6. Limits of Human Exposure to Radio frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz,

1999.

•

Australian Communications Authority Radio communications (Electromagnetic Radiation - Human Exposure) Standard 2003.

•

ANATEL, Brazil Regulatory Authority, Resolution 303 (July 2, 2002) “Regulation of the limitation of exposure to

* The information provided in this document supersedes the general

safety information in user’s guides published prior to May 1, 2006

Legal and Safety

electrical, magnetic, and electromagnetic fields in the radio frequency range between 9 kHz and 300 GHz.” “Attachment to Resolution 303 from July 2, 2002."

Operational Precautions

For optimal mobile device performance, and to be sure that human exposure to RF energy does not exceed the guidelines set forth in the relevant standards, always follow these instructions and precautions.

Phone Operation

When placing or receiving a phone call, hold your mobile phone as you would a landline telephone.

Speak directly into the

microphone

Two-way radio operation

Your radio product has been designed and tested to comply with national and international standards and guidelines regarding human exposure to RF electromagnetic energy, when operated in the two-way mode (at the face, or at the abdomen when using an audio accessory) at usage factors of up to 50% talk/50% listen.

Transmit no more than the rated duty factor of 50% of the time. To tran

smit (talk), push the PTT button. To receive calls, release the PTT button. Transmitting 50% of the time or less, is important because this radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).

When using your radio product as a traditional two-way

radio,

hold the radio product in a vertical position with the microphone one to two inches (2.5 to 5 cm) away from the lips

If you wear the mobile device on your body, always place the mobile device in a Motorola approved clip, holder, holster, case or body harness. If you do not use a body-worn accessory supplied or approved by Motorola and are not using the mobile device in the intended use positions along side the head in the phone mode or in front of the face in the two-way radio mode, or if you hang your device from a lanyard around your neck, keep the device at least 2.5 centimeters (1 inch) from your body when transmitting.

Approved Accessories

For a list of approved Motorola accessories call 1-800-453-0920, or visit our website at

www.motorola.com/iden.

RF Energy Interference/Compatibility

Nearly every electronic device is subject to RF energy interference from external sources if inadequately shielded, designed or otherwise configured for RF energy compatibility. In some circumstances your mobile device may cause interference with other devices.

Legal and Safety

Follow Instructions to Avoid Interference Problems

Turn OFF your mobile device in any location where posted notices instruct you to do so.

In an aircraft, turn off your mobile device whenever instructed to do so by airline staff. If your mobile device offers an airplane mode or similar feature, consult airline staff about using it in flight.

Implantable Medical Devices

If you have an implantable medical devices, such as a pacemaker or defibrillator, consult your physician before using this mobile device.

Persons with implantable medical devices should observe the following precautions:

•

ALWAYS keep the mobile device more than 20 centimeters (8 inches) from the implantable medical device when the phone is turned ON.

•

DO NOT carry the mobile device in the breast pocket;

•

Use the ear opposite the implantable medical device to minimize the potential for interference.

•

Turn OFF the mobile device immediately if you have any reason to suspect that interference is taking place.

Read and follow the directions from the manufacturer of your implantable medical device. If you have any questions about using

your mobile device with your implantable medical device, consult your health care provider.

Hearing Aids

Some phones may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer or physician to discuss alternatives.

Other Medical Devices and Health Care Facilities

If you use any other personal medical devices, consult your physician or the manufacturer or your device to determine if it is adequately shielded from RF energy. Turn off your radio product when instructed to do so in hospitals or health care facilities that may be using equipment that is sensitive to external RF energy.

Bluetooth

This device supports Bluetooth 1.2 including HSP, HFP, OPP, DUN, PBAP, and BPP. In order for Bluetooth devices to communicate with one another, they must utilize the same Bluetooth profile. To determine the profiles supported by other Motorola devices, visit www.hellomoto.com/bluetooth. For other devices, contact their respective manufacturer.

Certain Bluetooth features including those listed may not be supported by all compatible Bluetooth-enabled devices, and/or the functionality of such features may be limited in certain devices, or by certain wireless carriers. Contact your wireless carrier about feature availability and functionality.

Legal and Safety

Caring for the Environment by Recycling

This symbol on a Motorola product means the product should not be disposed of with household was

te.

Disposal of your Mobile Device and Accessories

Please do not dispose of mobile devices or electrical accessories (such as chargers, headsets, or batteries) with your household waste. These items should be disposed of in accordance with the national collection and recycling schemes operated by your local or regional authority. Alternatively, you may return unwanted mobile devices and electrical accessories to any Motorola Approved Service Center in your region. Details of Motorola approved national recycling schemes, and further information on Motorola recycling activities can be found at:

www.motorola.com/recycling

Disposal of your Mobile Device Packaging and User’s Guide

Product packaging and user’s guides should only be disposed of in accordance with national collection and recycling requirements. Please contact your regional authorities for more details.

Driving Precautions

The use of wireless phones while driving may cause distraction. Discontinue a call if you can’t concentrate on driving.

Additionally, the use of wireless devices and their accessories may be

prohibited or restricted in certain areas. Always obey the laws

and regulations on the use of these products. Responsible driving practices can be found in the “Smart Practices

hile Driving” section (see page 97).

Operational Warnings

Obey all posted signs when using Mobile devices in public areas.

Potentially Explosive Atmospheres

Areas with potentially explosive atmospheres are often but not always posted, and can include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, or areas where the air contains chemicals or particles, such as grain, dust or metal powders.

When you are in such area, turn off your handset, and do not remov

e, install, or charge batteries unless it is a radio product type especially qualified for use in such areas as “Intrinsically Safe” (for example, Factory Mutual, CSA, or UL approved). In such areas, sparks can occur and cause an explosion or fire.

Legal and Safety

Symbol Key

Your battery, charger, or portable radio may contain symbols, defined as follows:

Symbol Definition

Important safety information follows.

Do not dispose of your battery or

phone in a fire.

Your battery or phone may re

quire recycling in accordance with local laws. Contact your local regulatory authorities for more information.

Do not throw your battery or pho

ne in the trash.

Your phone contains an i

nternal lithium ion battery.

Do not let your battery, c

harger, or phone get wet.

Listening at full volume to music or voice through a headset may damage your hearing.

Batteries and Chargers

Caution: Improper treatment or use of batteries may present a danger of fire, explosion, leakage, or other hazard. For more information, see the “Battery Use and Battery Safety” section in this user’s guide.

Keep Your Mobile Device and Its Accessories Away from Small Children

These products are not toys and may be hazardous to small children. For example:

•

A choking hazard may exist for small, detachable parts.

•

Improper use could result in loud sounds, possibly causing hearing injury.

•

Improperly handled batteries could overheat and cause a burn.

Glass Parts

Some parts of your mobile device may be made of glass. This glass could break if the product is dropped on a hard surface or receives

032374o

032376o

032375o

032378o

Li Ion BATT

Symbol Definition

Legal and Safety

a substantial impact. If glass breaks, do not touch or attempt to remove. Stop using your mobile device until the glass is replaced by a qualified service center.

Seizures/Blackouts

Some people may be susceptible to epileptic seizures or blackouts when exposed to flashing lights, such as when playing video games. These may occur even if a person has never had a previous seizure or blackout.

If you have experienced seizures or blackouts, or if you have a fami

ly history of such occurrences, please consult with your physician before playing video games or enabling a flashing-lights feature (if available) on your mobile device.

Discontinue use and consult a physician if any of the following sy

mptoms occur: convulsion, eye or muscle twitching, loss of awareness, involuntary movements, or disorientation. It is always a good idea to hold the screen away from your eyes, leave the lights on in the room, take a 15-minute break every hour, and stop use if you are very tired.

Caution About High Volume Usage

Warning:

Warning: Exposure to loud noise from any source for extended periods of time may affect your hear

ing. The louder the volume sound level, the

less time is required before your hearing could be affected. To protect your hearing:

•

Limit the amount of time you use headsets or headphones at high volume.

•

Avoid turning up the volume to block out noisy surroundings.

•

Turn the volume down if you can’t hear people speaking near you.

If you experience hearing discomfort, including the sensation of pres

sure or fullness in your ears, ringing in your ears, or muffled speech, you should stop listening to the device through your headset or headphones and have your hearing checked.

For more information about hearing, see our Web site at

direct.motorola.com/hellomoto/nss/AcousticSafety.asp

(in English only).

Repetitive Motion

When you repetitively perform actions such as pressing keys or entering finger-written characters, you may experience occasional discomfort in your hands, arms, shoulders, neck, or other parts of your body. If you continue to have discomfort during or after such use, stop use and see a physician.

Service and Repairs

If you have questions or need assistance, we’re here to help. Go to

www.motorola.com/support

, where you can select from a number of customer care options. You can also contact the Motorola Customer Support Center at 1 (800) 453-0920 (United

Legal and Safety

States), 1 (877) 483-2840 (TTY, TDD United States for hearing impaired).

Export Law Assurances

This product is controlled under the export regulations of the United States of America and Canada. The Governments of the United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs and International Trade.

Battery Use and Safety

Important: Handle and store batteries properly to avoid injury or damage.

Most battery issues arise from improper handling of batteries, and particularly from the continued use of damaged batteries.

DON’Ts

• Don’t disassemble, crush, puncture, shred, or otherwise attempt to change the form of your battery.

• Don’t let the phone or battery come in contact with water.

Water can get into the phone’s circuits, leading to corrosion. If the phone and/or battery get wet, have them checked by your carrier or contact Motorola, even if they appear to be working properly.

• Don’t allow the battery to touch metal objects.

If metal objects, such as jewelry, stay in prolonged contact with the battery contact points, the battery could become very hot.

• Don’t place your battery near a heat source.

Excessive heat can damage the phone or the battery. High temperatures can cause the battery to swell, leak, or malfunction. Therefore:

•

not

dry a wet or damp battery with an appliance or

heat source, such as a hair dryer or microwave oven.

•

Avoid leaving your phone in your car in high temperatures.

DOs

• Do avoid dropping the battery or phone.

Dropping these items, especially on a hard surface, can potentially cause damage.

• Do contact your service provider or Motorola if your phone or battery has been damaged from dropping or high temperatures.

Important: Use Motorola Original products for quality assurance and safeguards.

To aid consumers in identifying authentic Motorola batteries from non-original or counterfeit batteries (that may not have adequate safety protection), Motorola provides holograms on its batteries. Consumers should confirm that any battery they purchase has a “Motorola Original” hologram.

Legal and Safety

Motorola recommends you always use Motorola-branded batteries and chargers.

Motorola mobile devices are designed to work with Motorola batteries. If you see a message on your display such as

Invalid Battery

Unable to Charge

, take the following

steps:

•

Remove the battery and inspect it to confirm that it has a “Motorola Original” hologram;

•

If there is no hologram, the battery is not a Motorola battery;

•

If there is a hologram, replace the battery and retry charging it;

•

If the message remains, contact a Motorola authorized service center.

Important:

Motorola’s warranty does not cover damage to the

phone caused by non-Motorola batteries and/or chargers.

Warning:

Use of a non-Motorola battery or charger may present a

risk of fire, explosion, leakage, or other hazard.

Proper and safe battery disposal and recycling:

Proper battery disposal is not only important for safety, it benefits the environment. Consumers may recycle their used batteries in many retail or service provider locations. Additional information on proper disposal and recycling may be found on the Web:

• www.motorola.com/recycling

• www.rbrc.org/call2recycle/

(in English only)

Disposal:

Promptly dispose of used batteries in accordance with local regulations. Contact your local recycling center or national recycling organizations for more information on how to dispose of batteries.

Warning:

Never dispose of batteries in a fire because they may

explode.

Battery Charging

Notes for charging your phone’s battery:

•

When charging your battery, keep it near room temperature. Never expose batteries to temperatures below 0°C (32°F) or above 45°C (113°F) when charging.

•

New batteries are not fully charged.

•

New batteries or batteries stored for a long time may take more time to charge.

•

Motorola batteries and charging systems have circuitry that protects the battery from damage from overcharging.

Specific Absorption Rate

Your model wireless phone meets the governmental requirements for exposure to radio waves.

Your mobile device is a radio transmitter and receiver. It is designed and manufactured to not exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications

Legal and Safety

Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed for the safety of all persons, regardless of age or

health, and to account for any variations in measurements. The exposure standard for mobile devices employs a unit of

measurement known as the Specific Absorption Rate (SAR). The SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 watts per kilogram (W/kg), averaged over one gram of tissue. Tests for SAR are conducted using procedures accepted by the FCC and by Industry Canada with the mobile device transmitting at its highest certified power level in all tested frequencies. Although the SAR is determined at the highest certified power level, the actual SAR level of the mobile device while operating can be below the maximum value. This is because the mobile device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station, the lower the power output.

Before a mobile device is available for sale to the public in the U.S. and Canada, it must be tested and certified to the FCC and Industry Canada that it does not exceed the limit established by each government for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body)

submitted to the FCC and available for review by Industry Canada. The highest SAR value for this mobile device when tested for use at the ear is 1.17 W/kg, and when worn on the body, as described in this guide, is 1.41 W/kg. Body-worn measurements can differ, depending upon available accessories and regulatory requirements. The SAR information includes the Motorola testing protocol, assessment procedure, and measurement uncertainty range for this product.

While there may be differences between the SAR levels of various mobile devices and at various positions, they meet the governmental requirements for safe exposure. Please note that improvements to this product model could cause differences in the SAR value for later products; in all cases, products are designed to be within the guidelines.

Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site:

http://www.phonefacts.net

or the Canadian Wireless Telecommunications Association (CWTA) Web site:

http://www.cwta.ca

AGPS and Emergency Calls

When you make an emergency call, your mobile device can use Assisted Global Positioning System (AGPS) satellite signals to tell the emergency response center your approximate location.

Legal and Safety

The AGPS feature has limitations, so always tell the emergency response center your best knowledge of your location. Remain on the phone for as long as the emergency response center instructs you.

AGPS

might not work

for emergency calls, if your local emergency response center does not process AGPS location information. For details, contact your local authorities.

If your mobile device cannot find strong AGPS satellite signals, the location of the nearest cell tower in contact with your mobile device is automatically provided to the emergency response center.

AGPS Performance Tips

•

Go outside and away from underground locations, covered vehicles, structures with metal or concrete roofs, tall buildings, and foliage. Indoor performance might improve if you move closer to windows, but some window sun shielding films can block satellite signals.

•

Move away from radios, entertainment equipment, and other electronic devices that might interfere with or block AGPS satellite signals.

AGPS uses satellites controlled by the U.S. government and subject to changes implemented in accordance with the Department of Defense AGPS user policy and the Federal Radio Navigation Plan. These changes might affect AGPS performance.

Motorola Limited Warranty for the United States and Canada

What Does this Warranty Cover?

Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES AND SOFTWARE PURCHASED IN THE UNITED STATES OR CANADA

Subject to the exclusions contained below, Motorola, Inc. warrants its Motorola iDEN Digital Mobile and Portable Handsets ("Products"), Motorola-branded or certified accessories sold for use with these Products ("Accessories") and Motorola software contained on CD-Roms or other tangible media and sold for use with these Products ("Software") to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below.

This limited warranty is a consumer's exclusive remedy, and applies as follows to new Products, Accessories and Software purchased by consumers in the United States or Canada, which are accompanied by this written warranty:

Products Covered Length of Coverage

Products as defined above.

One (1) year

from the date of purchase by the first consumer purchaser of the product.

Legal and Safety

What is not covered? (Exclusions)

Normal Wear and Tear

. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage.

Ornamental Decorations

. Ornamental decorations such as emblems, graphics, rhinestones, jewels, gemstones and their settings, and other decorative elements, are excluded from coverage.

Batteries

. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty.

Abuse & Misuse

. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded from coverage.

Use of Non-Motorola Products and Accessories

. Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage.

Unauthorized Service or Modification

. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, including without limitation, software changes, or modification in any way by someone other than Motorola, or its authorized service centers, are excluded from coverage.

Altered Products

. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or

Accessories as defined above.

One (1) year

from the date of purchase by the first consumer purchaser of the product.

Products or Accessories that are Repaired or Replaced.

The balance of the original warranty or for ninety (90) days

from the date returned to the consumer, whichever is longer.

Software

as defined above. Applies only to physical defects in the media that embodies the copy of the software (e.g. CD-ROM, or floppy disk).

Ninety (90) days from the date of purchase.

Products Covered Length of Coverage

Legal and Safety

non-Motorola housings, antennas, or parts, are excluded from coverage.

Communication Services

. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products, Accessories or Software is excluded from coverage.

Software Embodied in Physical Media.

No warranty is made that the software will meet your requirements or will work in combination with any hardware or software applications provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected.

Software NOT Embodied in Physical Media

. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided "as is" and without warranty.

Who is covered?

This warranty extends only to the first

consumer purchaser, and is not transferable.

What will Motorola Do?

Motorola, at its option, will at no charge repair, replace or refund the purchase price of any Products, Accessories or Software that does not conform to this warranty. We may use functionally equivalent reconditioned/refurbished/pre-owned or new Products, Accessories or parts. No data, software or applications added to your Product, Accessory or Software, including but not limited to personal contacts, games and ringer tones, will be reinstalled. To avoid losing such data, software and applications please create a back up prior to requesting service.

How to Obtain Warranty Service or Other Information?

obtain service or information, please call: Motorola iDEN Customer Services 1-800-453-0920 or

954-723-4910 TTY-877-483-2840 Or visit us online at http://www.motorola.com/iden You will receive instructions on how to ship the Products,

Accessories or Software, at your expense, to a Motorola Authorized Repair Center. To obtain service, you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service provider, if applicable; (d) the name and location of the installation facility (if applicable) and, most importantly; (e) your address and telephone number.

What Other Limitations Are There?

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR

Legal and Safety

CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.

Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or from one jurisdiction to another.

Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted Motorola software such as the exclusive rights to reproduce and distribute copies of the Motorola software. Motorola software may only be copied into, used in, and redistributed with, the Products associated with such Motorola software. No other use, including without limitation disassembly of such Motorola software or exercise of the exclusive rights reserved for Motorola, is permitted.

Patent and Software Provisions

MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and Motorola will pay those costs and damages finally awarded

against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

a.That MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;

b.That MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and

c.Should the Product or parts become, or in MOTOROLA'S opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.

MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product or any parts thereof.

Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA

Legal and Safety

software, such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise or rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.

Hearing Aid Compatibility With Mobile Phones

Some Motorola phones are measured for compatibility with hearing aids. If the box for your particular model has “Rated for Hearing Aids” printed on it, the following explanation applies.

When some mobile phones are used near some hearing devices (hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference they generate.

The wireless telephone industry has developed ratings for some of their mobile phones, to assist hearing device users in finding phones that may be compatible with their hearing devices. Not all

phones have been rated. Phones that are rated have the rating on their box or a label on the box.

The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.

M-Ratings:

Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices than phones that are not labeled. M4 is the better/higher of the two ratings.

T-Ra ti ng s:

Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with a hearing device’s telecoil (“T Switch” or “Telephone Switch”) than unrated phones. T4 is the better/higher of the two ratings. (Note that not all hearing devices have telecoils in them.)

Hearing devices may also be measured for immunity to this type of interference. Your hearing device manufacturer or hearing health professional may help you find results for your hearing device. The more immune your hearing aid is, the less likely you are to experience interference noise from mobile phones.

Legal and Safety

Information From the World Health Organization

Present scientific information does not indicate the need for any special precautions for the use of mobile phones. If you are concerned, you may want to limit your own or your children’s RF exposure by limiting the length of calls or by using hands-free devices to keep mobile phones away from your head and body.

Source: WHO Fact Sheet 193 Further information:

http://www.who.int./peh-emf

Product Registration

Online Product Registration:

www.motorola.com/us/productregistration

Product registration is an important step toward enjoying your new Motorola product. Registering permits us to contact you for product or software updates and allows you to subscribe to updates on new products or special promotions. Registration is not required for warranty coverage.

Please retain your original dated sales receipt for your records. For warranty service of your Motorola Personal Communications Product you will need to provide a copy of your dated sales receipt to confirm warranty status.

Thank you for choosing a Motorola product.

Wireless: The New Recyclable

Your wireless phone can be recycled. Recycling your phone reduces the amount of waste disposed in landfills and allows recycled materials to be incorporated into new products.

The Cellular Telecommunications Industry Association (CTIA) and its members encourage consumers to recycle their phones and have taken steps to promote the collection and environmentally sound recycling of end-of-life devices.

As a phone user, you have an important role in ensuring that this device is recycled properly. When it comes time to give this phone up or trade it in for a new one, please remember that the phone, the charger, and many of its accessories can be recycled. It's easy. To learn more about CTIA's Recycling Program for Used Wireless Devices, please visit us at:

http://recycling.motorola.young-america.com/ index.html

California Perchlorate Label

Some mobile phones use an internal, permanent backup battery on the printed circuit board that may contain very small amounts of perchlorate. In such cases, California law requires the following label:

Perchlorate Material - special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate

There is no special handling required by consumers.

Legal and Safety

Patent and Trademark Information

Microsoft and Microsoft Internet Explorer are registered trademarks of Microsoft Corporation.

T9 is a trademark owned by Tegic Communications. T9

Text Input Patent and Trademark Information.

This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541, U.S. Pat. 6,011,554 and other patents pending.

Java and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.

All other product names or services mentioned in this manual are the property of their respective trademark owners.

Software Copyright Notice

Motorola products may include copyrighted Motorola and third party software stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any

manner to the extent allowed by law. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.

Privacy and Data Security

Motorola understands that privacy and data security are important to everyone. Because some features of your mobile device may affect your privacy or data security, please follow these recommendations to enhance protection of your information:

• Monitor access—

Keep your mobile device with you and do not leave it where others may have unmonitored access. Lock your device’s keypad where this feature is available.

• Keep software up to date—

If Motorola or a software/application vendor releases a patch or software fix for your mobile device that updates the device’s security, install it as soon as possible.

• Erase before recycling—

Delete personal information or data from your mobile device prior to disposing of it or turning it in for recycling. For instructions on how to delete all personal information from your device, please contact your local service provider.

Motorola I465, Mike i465 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual