Motorola ME7052 User Manual

Welcome

Important Safety Instructions

Model ME7050 Series

DIGITAL CORDLESS PHONE

Model ME7052 Series

DIGITAL CORDLESS PHONE

WITH SPEAKERPHONE

Model ME7060 Series

DIGITAL CORDLESS PHONE

WITH DIGITAL ANSWERING MACHINE

Congratulations on your purchase of a Motorola product! Your MotorolaTelephone at a glance:

For product-related questions, please refer to the Warranty section.

Please retain your original dated sales receipt for your records. For warranty service of your Motorola Product, you will need to provide a copy of your dated sales receipt to condﬁlm warranty status.

Complies with the essential protective requirements and objectives of the EC's R&TTE Directive 1999/5/EC; EC Low Voltage Directive 72/23/EEC; EC EMC Directi ve 89/336/EEC

Copyright © 2007 Motorola, Inc. All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation)without written permission from Motorola, Inc.

Motorola reserves the right to revise this publication and to make changes to content from time to time without obligation on the part of Motorola to provide notiﬁcation of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including but not limited to, the implied warranties of merchantability andﬁtness fora particular purpose. Motorola may make improvements or changes to the product(s) described in this manual at any time.

MOTOROLA, the Stylized M Logo, and PhoneWrap are registered in the U.S. Patent and Trademark Ofﬁce. All other product or service names are the property of their respective owners.

Important Safety Instructions

Follow these safety precautions when using your cordless phone to reduce the risk of ﬁre, electric shock and injury to persons or property:

Reduce risk of ﬁre and shock by:

Keep all slits and openings of the phone unblocked. Do not set the phone on a hot surface or over a radiator. Ensure that proper ventilation is provided at the installation site. Do not use while wet or while standing in water.

2. Do not use this product near water (for example, near a bath tub, kitchen sink, or

3. swimming pool). Do not allow anything to rest on the power cord. Place the power cord so that it

4. will not be walked on. Never insert objects of any kind into the product slits as that may result in ﬁre or

5. shock. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners

6. or aerosol cleaners. Use a damp cloth for cleaning. Do not disassemble this product. If service or repair work is required, contact the

7. Warranty Service phone number found in the back of this user's guide. Do not overload wall outlets and extension cords.

9. Avoid using during an electrical storm. Do not use this cordless phone to report a gas leak, especially if you are in the

10. vicinity of the gas leak.

Unplug this cordless phone immediately from an outlet if:

The power cord or plug is damaged or frayed. Liquid has been spilled into the product. If the product becomes submerged in water, Do not retrieve the base until after you have unplugged the power and phone cords from the wall. Then retrieve

the unit by the unplugged cords. The product has been dropped or the cabinet has been damaged. The product exhibits a distinct change in performance.

It may result in serious injury.

User's Guide

Digital 1.8 GHz

1 2

Installation Guidelines

Read and understand all instructions and keep them safe for future reference.

1. Follow all warnings and instructions marked on the product.

2. Do not install this product near a bath tub, sink or shower.

Do not place this product on an unstable surface. This product may fall, causing serious damage to the product.

Adjust only those controls that are covered by the operating instructions. Improper adjustment ofother controls may result in damage and will often require extensive work to restore the product back to normal operation. Clean this product with a soft, damp cloth. Do not use chemicals or cleaning agents

6. to clean this phone.

Use only the power supply that came with this unit. Using other power supplies may damage the unit.

y, you should have at least one phone

Because cordless phones operate on electricit in your home that isn't cordless, in case the power in your home goes out. To avoid interference to nearby appliances, do not place the base of the cordless

9. phone on or near aTV, microwave oven, or VCR.

10.

It is impossible to make emergency calls when the keypad lock is enabled.

Technical Amendments

These Operating Instructions are issued for information purposes.Their content is not the subject of a contract. All indicated data are merely nominal values.The described equipment and

country.

This device is dedicated to be used in the analog public switched telecomunication network (PSTN).

Installation

Package Contents

Base Station

Mobile Handset

Mains Adaptor

Telephone Line Cord

Rechargeable Batteries type micro AAA

Charger Unit

User's Guide

Please check the contents of the package carefully. If s om ething is m is s ing or has become damaged in transit, you should NOT use the telephone. In such a case you should return to the dealer with your sales receipt or contact the Motorola's distributor directly. (For details, please refer to theW arranty section.)

Note: Retain the packaging of your appliance to prevent it from being damaged should you ever need to return it.

Single Pack

Twi n Pa ck

Setting up the Base Station and Charger Unit

Place the base station and charger unit in an easily accessible location. Make sure

the location, also make sure that all cables can be routed so as to prevent people tripping over them. Furthermore, avoid placing the base station and charger unit in the immediate vicinity of other electronic appliances such as microwaves, PCs or HiFi's, for example.We recommend a clearance distance of 1metre is kept between the phone and other equipment.

Do not expose the base station and charger unit to direct sunlight. Do not allow the base station and charger unit to become wet. They should not be set up in rooms which are subject to condensation or corrosive steam or a high concentration of dust (e.g. cellars, garages or conservatories). The room temperature must be between 0

Triple Pack

Quad Pack

C and 350C.

Connecting the Base Station and Mains Adaptor

Route the cable

Insert the plugs in the corresponding socket of the base station. beneath the telephone towards the back.

adaptor in the wall socket. The base station is now ready for use.

The base station does not have a power switch. Make sure that there is a mains socket nearby and that the mains adaptor is easily accessible. Check that the voltage indicated on the mains adaptor corresponds to that of your mains supply.

Open the battery compartment, by pushing downwards on the cover.

Insert the 2 x AAA (600mAh/1.2V) Ni-MH re-chargeable batteries supplied, observing the correct polarity.

CAUTION: Please do not use Alkaline or non-rechareable batteries. It may cause permanent damage to the unit and void the warranty. Non rechargeable batteries can explode and cause injuries and heavy damage on your environment.

Note: For fully discharged batteries, the handset will power on after a 15-minute precharge.

Plug in the telephone plug.Insert the mains

MOTOROLA and the Stylized M Logo are registered in the US Patent and

Trademark Ofﬁce. All other product or service names are the property of

Features

Congratulations on your purchase of this high quality, cordless telephone set. The set offers the following features:

Standards

Caller ID on Call Waiting (dependent on network)

Backlight display

* user must subscribe to the network's caller id service. + more then one handset required.

Programmable call barring

Operation with 2 standard AAA re-chargeable batteries

Handsfree (for Model ME7052)

Digital Answering Machine with 12 minutes recording time , 59 messages capacity (for Model ME7060)

7 8 9 10

Controls and Indication

On Handset and Base

handset volume

Cancel/Delete

Handsfree/Speaker key(for Model ME7052)

On Answering Machine (for Model ME7060)

Menu key-press to open the answering machine menu.

Volume down(-)-Press to decrease loudspeaker volume. Volume up(+)-Increase loudspeaker volume.

Page(Find Handset)keyPress to locate a missing handset/page all handsets registered to the base.

Rec./

Record/Memo key

Memo

Use to record your outgoing message or memo.

Message indicator ﬂashes with the number of new messages.

Delete key-Use to delete messages /memos.

Display icons

Indicates the battey charge status/level. No bars when battery is empty. Indicates that the outside line is engaged. Indicates an external call is in progress. Indicates an internal call is in progress. Indicates if you have unanswered calls. (Details available in the caller list).

Adjust the

Flash (Recall)key, Access a Call Waiting Line/Hold and transfer calls when connected to PABX for use with network services.

Key Lock

LED : Battery charging indicator

LED : Flashes with incoming calls

Paging key (call handset)

Replay/previous key During message playback, press to replay the current message or press twice to play the previous message.

Stop-Stops message playback. Ends recording.

Next key-During message playback,press to skip forward to the next message.

Play

Charging indicator Illuminates when the handset is charging in the base station.

Call indicator Flashes when you have incoming calls. Flashes when there has been a Voice mail received.

Indicates that the keypad lock is on. Microphone is muted. Ringer is switched off. Indicates the handset is registered on the base. Flashes if there is no link to the base. Scroll(UP) or (DOWN) to see further details of the entry.

Menu Structure

Navigate in the menu structure as follows: Press the Menu key

Then use the arrow keys to navigate through the menu or select the required menu item directly using the digit keys.

Example: Enter MENU > 3 > to access '1-RINGER' > '2-HS NAME', then enter the HS Name.

1-CALL LOG

2-PHONE BOOK

3-HANDSET

4-BASE

5-LANGUAGE

1-NEW ENTRY 2-LIST ENTRY 3-EDIT ENTRY 4-DELETE 5-DELETE ALL

1-RINGER

2-HS NAME 3-PREFIX MEM 4-KEY TONE 5-AUTO ANS 6-CALL TIMER 7-DEFAULT 8-REGISTER

1-BARRING

2-EMERGENCY

3-RINGER (-----) MELODY 1-- MELODY 10 (for Model ME7050/ME7052) 4-FLASH TIME

5-DIAL MODE

6-CHANGE PIN 7-DEFAULT 8-DEREGISTER

ENGLISH,DEUTSCH,ITALIANO,FRANCAIS,ESPANOL, PORTUGUES,NEDERLANDS,POLSKI,SVENSKA,TURKCE

ENTER PIN

100/250/600

TONE PULSE

ENTER PIN ENTER PIN

ENTER PIN

CONFIRM?

1-VOLUME 2-EXT RINGER 3-INT RINGER

ON / OFF ON / OFF ON / OFF CONFIRM? SEARCHING

ENTER NAMEENTER NO

HANDSET 1-4

12-

NEW PIN CONFIRM?

HANDSET 1-4

[-----] MELODY 1-10 MELODY 1-10

DISABLE EXTERNAL NUMBER

REPEAT

CONFIRM?

NORMAL RING VIP RING 1-10

ENTER NO

Using the Telephone

Switching the Handset On/Off

When the handset is placed on the base station or charging unit, it switches on automatically and starts to charge up. Allow the batteries to be charged for 14 hours

On/Off switch.

Backlight

backlight

Selecting the Language

Ten different languages are available for selection for each handset. Proceed as follows to select a language:

Press the key repeatedly until menu item LANGUAGE appears.

1. Press the

Press or as often as necessary to select the required language.

Press the

Making Internal Calls

If more than one handset is registered on the base station, internal calls can be made free of charge.

Press the key.

Press the number of the required handset (1..4) and wait for the called party to answer.

Press the key to end the call.

Note: If an external call is received during an internal call, a beep will be heard.

Making External Calls

There are two ways to dial a number, namely direct dialling or on-hook dialling.

Directt dialling

Press the key and wait for the dialling tone.

Dial the telephone number and complete the call.

Press the key to end the call.

On-hook dialling

Dial the telephone number.

Delete any incorrect entries by pressing the key.

Press the key.The number entered is dialled and a connection established.

Press the key to end the call.

(For Model ME7052)

Taking Calls

When an external call is received, all the handsets registered and the base station ring.

1. Take the handset from the base station; a connection is automatically established

2. Press the key to end the call.

(when the AUTO ANS function is active). Otherwise, press the key.

Press the key. Press the key to end the call.

/charger cradle

Preﬁx Dialling

1.2.Press the 0 key for two seconds. Then dial the rest of the digits and press the key to establish a connection.

Note: The preﬁx number (e.g. an access code) must have been programmed before hand. Refer to "Handset Settings".

Dialling from the Phone Book

Press the key; the ﬁrst entry in the phone book appears.

1. Press the or key to select the required entry from the phone book.

2. Alternatively, enter the ﬁrst letter of the name required. Press the key. The number is dialled.

Paging Handsets

If you cannot locate a handset you can use the key on the base to help find it.

1. Press the key on the base.

All handsets registered to the base will ring and the display on each handset will show Paging.

2. To stop the paging ring,press the key on the base again,or press any key on the

handset. Note: All paged handsets will stop ringing if any key on the handset or page key on the base is pressed.

11 12 13 14

Call Log Operations

IMPORTANT: To use the CALL LOG function, you must subscribe to your network operator’s Caller Line Identiﬁcation (CLI) service.

If you have subscribed to the Network Caller Display service, the calls list will record details of any call that arrives. To view the calls list:

Press the key as often as necessary until the CALL LOG menu appears.

1. Press the key. Alternatively, press and hold the key.

2. Press the or keys to browse through the CALL LOG memory.

3. Press the key to return the call.

4. Press and hold the key two seconds to delete one or all the entries.

5. Press the key to enter the caller's details in the phone book.

Press the key

Enter the name.

8. Press the key.

10.

Press the or key to select the normal ring or VIP ring 1-10.

You must subscribe to the network Caller Display service to use the VIP ring feature.

If a VIP ring is assigned for that entry, a digit “ ” will be shown in front of the name during the incoming call or browsing.

11.Press the key to save the entry. Note: 1. The CALL LOG symbol and display indicator only disappear after browsing

through all the entries. 2. It is only possible to enter caller's details in the phone book

who are not already entered.

Voice mail service

Voice mail is an automatic answering service offered by your service provider / telephone company.If you subscribe to this service,your service provider/telephone company’s voice mail system will answer calls for you when you are unavailable to answer the phone or when your line is busy.Messages are recorded by your service provider /telephone company,not your telephone.Please consult your service provider/telephone company for details of this service.

VOL-

VOL+

Muting the Microphone

Press the key to switch the microphone on

1. or off during a call.

Redial Function

Press the key as offen as necessary to view the last 5 Redialled numbers and Press the key to dial the Chosen number.

Access a CallWaiting Line / Holding and transferring calls (PABX)

When on an external call, press key to access a CallWaiting Line when you hear the call waiting prompt signal. Press key again to toggle between the two calls.

When on an external call (PABX line)

1. Press key to put the call on hold.

2. Dial the number of the extension.

3. Press key again if you would like to take back the call, or to transfer Note:you may have to subscribe to a call waiting service. contact your telephone

provider for more information.

the call.

Teleconference and Intercom Call Transfer

Intercom Call Transfer

It is possible to put an external call on hold and call another handset registered to the base or to forward calls.

1. Press key to hold the external call and initiate an internal call.

2. Input the desired handset number (e.g. 2).

3. The target handset will ring. After the internal connection is made, press key to transfer the external call.

4. If key is pressed before another handset is answered, the call transfer procedure will be cancelled and the external call connection is regained.

5. If key is pressed before another handset is answered, both the external and internal call will be disconnected.

Teleconference

After having received an external call, it is possible to include a second handset in the conversation (three-way conference).

Press the key and enter the number of the corresponding handset (e.g. 2) which should be included in the call.

The external caller is put on hold. As soon as handset 2 takes the call, press key to transfer the call to handset 2. Or

The external caller is put on hold. as soon as handset 2 takes the call, press and hold key to activate the teleconference.

By pressing the key, any of the handsets can be disconnected from the teleconference and the other handset continues with the external call.

Entering a Dialling Pause (P)

If the MOTOROLA telephone is connected to a PBX system, it may be necessary to insert a dialling pause. To do this, press the key after entering the

relevant digit, e.g. 0, for an outside line (0P....). A 'P' appears in the display indicating

a pause. The pause can also be entered when programming numbers in the phone book.

Phone Book

caller, the handset displays the name of the caller (when stored in the phone book).

1. If a VIP ring is assigned for that entry, a digit “ ” will be shown in front of the name during the incoming call or browsing.

When the function is supported by the telephone provider service and the

The display will show 1 - NEW ENTRY

Press the or key to select the normal ring or VIP ring 1-10.

Alternatively, enter the ﬁrst letter of the name required.

repeatedly

Alternatively, enter the ﬁrst letter of the name required.

Edit the number.

Edit the name.

Delete Entries

Press the key as often as necessary until the PHONE BOOK menu appears.

Press the or key to select DELETE / DELETE ALL.

Press the or key to select the phone book entry. Alternatively, enter the

ﬁrst letter of the name required.

Press the key to conﬁrm the input.

Note: The delete process can be stopped at any time prior to conﬁrmation of it by pressing the key several times. if all the entries should be deleted, select DELETE ALL instead of DELETE at Pt. 2.

repeatedly

Vol.+

Vol.-

Use the key to delete existing characters.

Kitchen

person

/charger cradle.

Note: Even with the call timer off, the total call duration is shown at the end of the call.

Note: you only need to do this to replace a faulty handset

Page

DISABLE or EXTERNAL .

Barring Numbers

11. Use the (up) or (down) key to select NUMBER.

12. Press the INT/OK key.

13. Enter barring number (max 5 digits).

14. Press the INT/OK key. Note: All numbers which start with the barring number will be barred, e.g. if 07 is stored as the barring number then all numbers starting with 07 will be barred.

Two emergency number 112 and 999 are already stored for you.

Flash

ﬂash

Note: The default time for Flash in SINGAPORE is 600ms.

20 21 22

FLASH

600ms

Note: You only need to do this to replace a faulty handset.

Answering Machine Operation

(for Model ME7060)

General

1. In the idle (standby) mode, press to program each of the following options: Turn Answering Machine On / Off Set the Day and Time Record your outgoing Announcement Set your Remote Access code Set 'Announce Only' On / Off Turn audible Message Alert On / Off Set Base ringer On / Off Set number of Rings to answer

Repeatedly press the key to step through the answer machine options.

The current setting of each is announced.

Once the desired option is reached and the current setting of each is announced,

2. press or to change the setting.

Note: It is not possible to change the A1 or A2 setting at this time

Press to conﬁrm your setting.

3. At any time, press to exit setup mode.

Switch Answering Machine ON/OFF (preset to ON)

When you ﬁrst switch on your phone, the answering machine is in the mode.

Press . Until you hear 'answer on' or 'answer off' and the dispaly shows 'An',

press or to switch

Clock Setting

Follow the steps above to program the current and then the :

First, program the Day. As you program, the display shows 'd' and a number, 1 to 7, representing the day of the week 1 represents Monday; 2 represents Tuesday, and so on. Press when done.

Next, program the Hour. Be careful that you program pm if the current time is in the afternoon or evening, or an am if the current time is after midnight or in the morning. Press when done.

Next, program the Minute. You'll be programming the 'tens' column ﬁrst. Your choices are 0 through 5 , as the minutes range from 00 to 59. Press . Now, you are programming the 'ones' column, where your choices are 0 through 9 . Press to conﬁrm.

Note: If the mains power to the base is lost, your answer machine will display "St." (Set time) to remind you adjust the clock when it is switch on.

between the On/Off setting.

, then the

Outgoing Announcement

You can record 2 different outgoing announcements: A1 inviting your caller to leave a message (Announce Only OFF), and A2 asking your caller to call back later (Announce Only ON).

Outgoing Announcement A1 is played when Announce Only mode is OFF. Callers can leave a message in this mode. Your answering machine is preset with Announce Only set to OFF, allowing callers to leave a message.

Outgoing Announcement A2 is played when Announce Only mode is ON. Callers cannot leave a message in this mode.

If you do not record your own announcements, your answering system will play a pre-programmed message to your callers:

A1: "Please leave your message after the beep." A2: "I am sorry that I am not available. Please call back later."

How to Record Your Announcement

Recording Announcement A1 (Announce Only set to OFF)

Press until you hear 'Announcement One '

1. Press . You will hear 'Now Recording' followed by a beep. Speak

2. toward the Base Unit. You have up to 60 seconds for your announcement. Your announcement must be at least 3 seconds in length. Press when ﬁnished. Your recording will be played automatically. If you're

3. not satisﬁed, record your announcement again.

Recording Announcement A2 (Announce Only set to ON)

Follow the same steps as recording Announcement A1. However, this time you will hear 'Announcement Two ' since you have set Announce Only to ON.

To Review/Delete You Announcement A1/A2

1. Press until you hear ' Announcement One' (Announce Only set to

OFF) or'Announcement Two' (Announce Only set to ON).

2. Press Play, you will hear the announcement of A1 or A2 (you can only review

the latest recorded announcement).

3. During playing the announcement of A1 or A2, press DEL to delete the current

announcement and the answering machine will use the default announcement.

Note: The default announcement cannot be deleted.

Set remote access code

Your Remote Access code allows you to retrieve messages, and record memos and announcements when you're away from your Answering Machine. The remote access code helps prevent unauthorised people from ringing up your answering machine and listening to your messages. The code can be any 4-digit

from to . The pre-set code is 0000 .

number,

1. Press until you hear "Remote access code is 0000 " and the display shows Ac.

2. Press or to set the ﬁrst digit between 0-9. Press to conﬁrm.

3. Repeat Step 2 until all 4 digits have been set. The machine announces the new code.

Remote Operation

1. Call your answering machine from any touch-tone phone.

2. When you hear your outgoing announcement, enter your 4-digit Remote Access code.

3. You can now perform the following functions:

IF YOU WANT TO PRESS Play messages in a mailbox

Repeat / Play Previous Message Stop playback or recording Play Next Message Delete current message Record a Memo Record Announcement

Turn System On /Off Play Help Menu

Set 'Announce Only' On / Off (preset to OFF)

Press MENU untill you hear “Announce Only is ON” or “Announce Only is OFF”and the diaplay shows “Ao” . Press or to swith between the ON/OFF setting.

If you want callers to leave messages, Announce Only must be set to OFF. If you do not want callers to leave messages, set Announce Only to ON . Follow the steps in the beginning of the Setup section.

Turn Audible Message Alert On / Off

Press MENU untill you hear “Message Alert is ON” or “OFF” and the display show “AL”. Press or to swith between the ON/OFF setting. With Message Alert seconds,alerting you to new

beginning of the

9999

0000

1 4 / Press 4 Twice 5 6 7 8, then 5 to Stop

press 7 to delete the

9, then 5 to Stop

announcement and return to the prerecorded announcement

0 *

programmed ON ,the Base unit will beep approximately every 10

Setup section to program this feature.

, unplayed messages and memos. Follow the steps in the

Turn Base Ringer On / Off (preset to ON)

Press MENU untill you hear “Base Ringer is ON ” or “ OFF” and the display shows “Br”. Press or to swith between the ON/OFF setting. Your Base Ringer is independent of the Handset ringer.To program this feature, follow the steps in the beginning of the Answering Machine section.

Set Number of Rings to Answer

Press MENU untill you hear “Number of ring selected is Two ” or “Number of ring selected is Toll Saver ” and the display shows “Nr” . Press or to swith between the Number/Toll Saver” setting. Your Answering System can answer after 2-6 rings or you can choose the Toll Saver option. The Toll saver option instructs the Answering System to answer after 4 rings only if there are new, unplayed messages; otherwise, it will answer after 6 rings. The beneﬁt to you is if you are making a long distance call to retrieve messages,if the Answering System does not answer after 4 rings, you can hang up. There are no new messages, and you will save the expense of a long distance call.To set the number of rings to answer,follow the steps in the beginning of the Setup section.

Recording a Memo

You can record a memo, either at the Base Unit or from a remote location. To record a Memo at the Base:

Press and hold .

You will hear ' Now Recording ', followed by a beep.

2. Speak towards the Base Unit. Press when ﬁnished. Your memo is stored

3. like a message from an outside caller.

To record a memo from a remote location, follow instructions in theRemote Operation section.

Note: If memory is full while recording, the answering machine will announce

"memory is full" and a beep is heard, at the same time the 7-segments LED will display "Fu" and the message count alternatively.

Listening to Your Messages

When you have new messages, the message counter will ﬂash, showing the number of unplayed messages.

The unit will ﬂash with the number of new messages. also the play key LED will ﬂash. For old messages this can only be seen by the play key led being on steady. The display will show 00 with either no messages at all or old messages, so cannot be used as an indicator.

Recorded messages and memos are retained until you delete them. If its capacity is full, the system will answer after 10 rings, and hear “Memory is full”.

the caller will

Message Playback

1. Press the Play key. The prompt will tell you how many new and old messages are stored in that Mailbox. If there are one or more new messages, only the new messages will be played. After new message playback is completed, you can press the Play key again to hear all old messages.

Note: If you short press the Play key, the order of playback is oldest messages ﬁrst, newest last. If you long press the Play key, the order of playback is newest messages ﬁrst, oldest last.

Before each message is played, the day and time it was recorded is announced.

2. Press to replay the current message from the beginning. Press twice to play the previously recorded message.

3. Press to skip to the next message.

4. Press STOP at any time to end playback.

Deleting Messages

To delete the message or memo currently playing, press

To delete all old messages stored :

In the idle mode, press and hold

2. All old messages will be deleted.

NOTE: New,unplayed messages cannot be deleted until you play them. Once you have deleted the message/s, it cannot be recovered.

. You will hear"All old Messages are Deleted"

Important information

There is a total of 12 minutes of record time. This includes messages, memos, and announcements.

The maximum number of messages that can be stored is 59 .

A message, memo, or announcement can be a maximum of 60 seconds.

If a call comes in while you are listening to messages, playback automatically stops.

23 24 25 26

Alcom Electronics Pte Ltd.

For details, please contact :

Alcom Electronics Pte Ltd 37 Kallang Pudding Road, #05-08, BLK-B Tong Lee Building, SINGAPORE 349315, PH : (65) - 68412668 F AX : (65) - 68412628 E-MAIL : support@alcom.com.sg www.alcomonline.com

27 28 29 30