Motorola MC33206D, MC33206P, MC33207D Datasheet
Dual
T
105°C
Quad
Order this document by MC33206/D
The MC33206/7 family of operational amplifiers provide rail–to–rail
operation on both the input and output. The inputs can be driven as high as
200 mV beyond the supply rails without phase reversal on the outputs and
the output can swing within 50 mV of each rail. This rail–to–rail operation
enables the user to make full use of the supply voltage range available. It is
designed to work at very low supply voltages (±0.9 V) yet can operate with a
single supply of up to 12 V and ground. Output current boosting techniques
provide a high output current capability while keeping the drain current of the
amplifier to a minimum.
The MC33206/7 has an enable mode that can be controlled externally.
The typical supply current in the standby mode is <1.0 µA (V
The addition of an enable function makes this amplifier an ideal choice for
power sensitive applications, battery powered equipment (ins trumentation and
monitoring), portable telecommunication, and sample–and–hold applications.
• Standby Mode (I
≤1.0 µA, Typ)
D
• Low Voltage, Single Supply Operation
(1.8 V and Ground to 12 V and Ground)
• Rail–to–Rail Input Common Mode Voltage Range
• Output Voltage Swings within 50 mV of both Rails
• No Phase Reversal on the Output for Over–Driven Input Signals
• High Output Current (I
• Low Supply Current (I
= 80 mA, Typ)
SC
= 0.9 mA, Typ)
D
• 600 Ω Output Drive Capability
• Typical Gain Bandwidth Product = 2.2 MHz
Enable
= Gnd).
LOW VOLTAGE
RAIL–TO–RAIL
OPERATIONAL AMPLIFIERS
SEMICONDUCTOR
TECHNICAL DATA
MC33206
P SUFFIX
PLASTIC PACKAGE
14
Output 1
Inputs 1
Enable 1
16
1
14
1
N.C.
1
2
N.C.
3
4
1
7
V
EE
(Dual, Top View)
MC33207
1
CASE 646
D SUFFIX
PLASTIC PACKAGE
CASE 751A
(SO–14)
N.C.
14
V
13
CC
Output 2
12
11
2
PLASTIC PACKAGE
Inputs 2
105
96
Enable 2
8
N.C.
P SUFFIX
CASE 648
ORDERING INFORMATION
Operational
Amplifier Function
This document contains information on a new product. Specifications and information herein
are subject to change without notice.
MOTOROLA ANALOG IC DEVICE DATA
Device
MC33206D
MC33206P
MC33207D
MC33207P Plastic DIP
Operating
Temperature Range
–
°
= –40 ° to +
A
°
Package
SO–14
Plastic DIP
SO–16
Motorola, Inc. 1996 Rev 0
16
1
Output 1
1
V
CC
Output 2
2
3
4
8
Inputs 1
Inputs 2 2
Enable 2, 3
1
(Quad, Top View)
D SUFFIX
PLASTIC PACKAGE
CASE 751B
(SO–16)
Enable 1, 4
16
Output 4
15
14
4
3
13
125
116
107
9
Inputs 4
V
EE
Inputs 3
Output 3
1
MC33206 MC33207
MAXIMUM RATINGS
Rating Symbol Value Unit
Supply Voltage (VCC to VEE) V
ESD Protection Voltage at any Pin
Human Body Model
Voltage at any Device Pin V
Input Differential Voltage Range V
Common Mode Input Voltage Range (Note 2) V
Output Short Circuit Duration (Note 3) t
Maximum Junction Temperature T
Storage Temperature Range T
Maximum Power Dissipation P
NOTES: 1. The differential input voltage of each amplifier is limited by two internal parallel back–to–back
diodes. For additional differential input voltage range, use current limiting resistors in series
with the input pins.
2.The common–mode input voltage range of each amplifier is limited by diodes connected from
the inputs to both power supply rails. Therefore, the voltage on either input must not exceed
either supply rail by more than 500 mV.
3.Power dissipation must be considered to ensure maximum junction temperature (TJ) is not
exceeded.
4.ESD data available upon request.
V
S
ESD
DP
IDR
CM
s
J
stg
D
13 V
2,000 V
VS ± 0.5 V
(Note 1) V
VCC + 0.5 to
VEE – 0.5
(Note 3) sec
+150 °C
–65 to +150 °C
(Note 3) mW
V
DC ELECTRICAL CHARACTERISTICS (V
= 5.0 V, VEE = 0 V, V
CC
= 5.0 V, TA = 25°C, unless otherwise noted.)
Enable
Characteristic Figure Symbol Min Typ Max Unit
Input Offset Voltage (VCM 0 to 0.5 V, VCM 1.0 to 5.0 V)
MC33206: TA = 25°C
MC33201: TA = –40° to +105°C
MC33207: TA = 25°C
MC33202: TA = –40° to +105°C
Input Offset Voltage Temperature Coefficient (RS = 50 Ω)
– V
IO
–
–
–
–
0.5
1.0
0.5
1.0
8.0
11
10
13
– ∆VIO/∆T – 2.0 – µV/°C
TA = –40° to +105°C
Input Bias Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V)
TA = 25°C
–
TA = –40° to +105°C
Input Offset Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V)
– IIO
TA = 25°C
TA = –40° to +105°C
Common Mode Input Voltage Range – V
Large Signal Voltage Gain (VCC = 5.0 V, VEE = –5.0 V)
– A
RL = 10 kΩ
RL = 600 Ω
Output Voltage Swing (VID = ±0.2 V)
–
RL = 10 kΩ
RL = 10 kΩ
RL = 600 Ω
RL = 600 Ω
IIB
ICR
VOL
V
OH
V
OL
V
OH
V
OL
–
–
–
–
–
V
EE
50
25
4.85
–
4.75
–
80
100
5.0
10
VCC + 0.2
VEE – 0.2
300
250
4.95
0.05
4.85
0.15
200
250
50
100
V
CC
–
–
–
–
0.15
–
0.25
Common Mode Rejection (Vin = 0 to 5.0 V) – CMR 60 90 – dB
Power Supply Rejection Ratio
VCC/VEE = 5.0 V/Gnd to 3.0 V/Gnd
Output Short Circuit Current (Source and Sink) – I
– PSRR
PSR
SC
–
66
25
92
500
–
50 80 – mA
mV
nA
nA
V
kV/V
V
µV/V
dB
2
MOTOROLA ANALOG IC DEVICE DATA
MC33206 MC33207
DC ELECTRICAL CHARACTERISTICS (continued) (V
Characteristic UnitMaxTypMinSymbolFigure
Power Supply Current (VO = 2.5 V, TA = –40° to +105°C,
per Amplifier)
MC33206: V
MC33206: V
MC33207: V
MC33207: V
Enable Input Voltage (per Amplifier)
Enabled – Amplifier “On”
Disabled – Amplifier “Off” (Standby)
Enable Input Current (Note 5) (per Amplifier)
V
V
V
V
NOTE: 5.External control circuitry must provide for an initial turn–off transient of <10 µA.
Enable
Enable
Enable
Enable
= 12 V
= 5.0 V
= 1.8 V
= Gnd
AC ELECTRICAL CHARACTERISTICS (V
Slew Rate (VS = ±2.5 V , VO = –2.0 to +2.0 V,
RL = 2.0 kΩ, AV = 1.0)
Gain Bandwidth Product (f = 100 kHz) – GBW – 2.2 – MHz
Phase Margin (RL = 600 Ω, CL = 0 pF) –
Gain Margin (RL = 600 Ω, CL = 0 pF) – A
Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) – CS – 90 – dB
Power Bandwidth (VO = 4.0 Vpp, RL = 600 Ω, THD ≤ 1%) – BW
Total Harmonic Distortion (RL = 600 Ω, VO = 1.0 Vpp, AV = 1.0)
f = 1.0 kHz
f = 10 kHz
Open Loop Output Impedance
(VO = 0 V, f = 2.0 MHz, AV = 10)
Differential Input Resistance (VCM = 0 V) – R
Differential Input Capacitance (VCM = 0 V) – C
Equivalent Input Noise Voltage (RS = 100 Ω)
f = 10 Hz
f = 1.0 kHz
Equivalent Input Noise Current
f = 10 Hz
f = 1.0 kHz
Time Delay for Device to Turn On – t
Time Delay for Device to Turn Off – t
= 5.0 Vdc
Enable
= Gnd (Standby)
Enable
= 5.0 Vdc
Enable
= Gnd (Standby)
Enable
= 5.0 V, VEE = 0 V, V
CC
Characteristic Figure Symbol Min Typ Max Unit
= 5.0 V, VEE = 0 V, V
CC
– I
– V
– I
Enable
– SR 0.5 1.0 – V/µs
–
– ZO – 100 – Ω
– e
– i
= 5.0 V, TA = 25°C, unless otherwise noted.)
Enable
D
–
–
–
–
Enable
Enable
= 5.0 V, TA = 25°C, unless otherwise noted.)
O
M
M
P
THD
in
in
n
n
on
off
–
–
–
–
–
–
– 65 – Deg
– 12 – dB
– 28 – kHz
–
–
– 200 – kΩ
– 8.0 – pF
–
–
–
–
– 10 – µs
– 2.0 – µs
0.8
0.5
1.5
0.5
VEE + 1.8
VEE + 0.3
2.5
2.2
0.8
0
0.002
0.008
25
20
0.8
0.2
1.125
6.0
2.25
6.0
–
–
–
–
–
–
–
–
–
–
pA/
–
–
mA
µA
mA
µA
V
µA
%
nV/
Hz
Hz
MOTOROLA ANALOG IC DEVICE DATA
3
V
CC
Enable
MC33206 MC33207
Figure 1. Circuit Schematic
(Each Amplifier)
V
CC
Vin –
Vin +
V
CC
V
CC
V
EE
4000
3500
3000
2500
2000
1500
1000
, MAXIMUM POWER DISSIPATION (mW)
500
0
D(max)
P
–60 –30
This device contains 96 active transistors (each amplifier).
Figure 2. Maximum Power Dissipation
versus T emperature
16 Pin DIP
14 Pin DIP
SO–14/SO–1
6
0 30 60 90 120 150
TA, AMBIENT TEMPERATURE (
°
C)
Figure 3. Input Offset Voltage Distribution
40
35
30
25
20
15
10
PERCENT AGE OF AMPLIFIERS (%)
5.0
0
–10 0 4.0 8.0 10–2.0 2.0 6.0–6.0–8.0 –4.0
360 amplifiers tested
from 3 wafer lots
VCC = 5.0 V
VEE = Gnd
TA = 25
DIP Package
VIO, INPUT OFFSET VOLTAGE (mV)
°
C
4
MOTOROLA ANALOG IC DEVICE DATA
Loading...